Search Results

Search found 12944 results on 518 pages for 'desktop publishing'.

Page 449/518 | < Previous Page | 445 446 447 448 449 450 451 452 453 454 455 456  | Next Page >

• CD and DVD burning very slow with LG DVD Burner

  - by Om Nom Nom

  I have an HP m7560in Desktop which came with an LG DVD burner. As far back as I can remember, it has been having problems in burning discs. It used to take about one and a half hour to burn 4 GB of data on a blank DVD-R. I am using Nero and ImgBurn and I usually select 8x speed for burning. I used to run XP earlier and now I run Windows 7 on it, but I face the problem on both. I have already checked that DMA mode is selected in the IDE controllers' properties. On XP, uninstalling the IDE controllers and DVD drive from the Device Manager, rebooting and letting it install the drivers again fixed the problem for a while, but after a couple reboots, the problem used to come back. On Windows 7, even doing that is not fixing the problem. In fact, in Windows 7, the burning process doesn't even begin. Imgburn gets stuck on the first stage (of writing Lead-In), and it never progresses until I turn off / reset the computer. I checked the disc info after this happened, and the disc still shows empty and ready to be burned on, so it's obvious that it didn't even touch the disc. I have already had the drive replaced once by HP, but it didn't fix the problem. Do you guys have any suggestions? (Note that Windows Updates doesn't give any newer driver for the controllers, or any other components for that matter).

  Read the article

• Computer speakers receive radio station signal

  - by squircle

  I have a set of Logitech 5.1 speakers where each speaker and the source plug into the subwoofer. I'm using a Griffin Firewave with output from my MacBook Pro, and output from my custom-built desktop with a switch in the middle (built it myself out of an old Belkin A/B parallel switch). Recently, I've noticed that I can hear a local Punjabi radio station being picked up by my speakers, and the volume of this interference increases as I increase the volume of the speakers. I'm fairly sure that this radio station is at the low-end of the FM spectrum, below 90MHz (or it may be at the high end, above 105MHz, my memory isn't infallible). It gets quite annoying as I can't put my audio very loud without the interference. I've tried to put a ferrite core on the input cable just before the 3.5mm jacks plug into the subwoofer. I don't know if putting the same core around all three of the cables (green, black, orange) would negate the effects, but I'm assuming not. There has been no change. Is there any reason why this would be happening? I'm assuming the interference is coming somewhere between the FireWave and the subwoofer, because the noise gets amplified with volume increases. If anybody has any suggestions, I'd be grateful!

  Read the article

• RDP problem with Vista and Windows 7 destination

  - by MadBison

  I use a server a home to host a bunch of concurrently running Hyper-V VM's with different OS's and software for testing. I have Vista on the laptop, all latest SP's and patches. The server is Server 2008 R2, fully patched. The guests are a mix of XP, Vista, Server 2008 and Windows 7. If I connect to the Win XP or Server 2008 guest using RDP, it is always good. Very quick, no speed issues. If I connect to the Vista or Win 7 guests, the response time is so slow it is unusable. Usually 6 or 8 seconds, and at times it is to long to measure! This happens from both the laptop running Vista, and the server running Server 2008 R2. Does anyone know what the issue is with RDP on Vista and Windows 7 destinations? I did read this: http://blog.tmcnet.com/blog/tom-keating/microsoft/remote-desktop-slow-problem-solved.asp and that is not the problem I have applied that change to all PC's.

  Read the article

• Failed to open the Parallels networking module

  - by user49204

  I'm running Parallels Desktop 7 on OSX Lion and encounter the issue in the subject on every time I'm trying to launch Parallels VM. The error message contains a hint to restore to network configuration default which does not help. As been advised by some forums to ran the following script: sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_hypervisor.kext" sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_hid_hook.kext" sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_usb_connect.kext" sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext" sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_vnic.kext" The output of: sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext" is: Diagnostics for /Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext: Warnings: The booter does not recognize symbolic links; confirm these files/directories aren't needed for startup: /Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext/Contents/CodeDirectory /Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext/Contents/CodeRequirements /Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext/Contents/CodeResources /Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext/Contents/CodeSignature Dependency Resolution Failures: No kexts found for these libraries: com.parallels.kext.prl_hypervisor I've noticed that prl_netbridge is not being loaded (when I'm trying to unload it, I'm notified it is not loaded). Am I doing something wrong? What can be the reason for such behaviour?

  Read the article

• Network corruption - corrupt downloads, corrupt streams, etc.

  - by rfrankel

  I've been having some problems with my home LAN. Downloaded executables won't run, my remote desktop sessions keep getting interrupted due to encryption errors, flash video streams show visible corruption (both Hulu and YouTube), and I've had a couple downloads for which the md5 hashes don't match. The problem has even occurred with a couple images embedded in webpages, though that's rare enough (presumably because images are relatively smaller files). I've had this problem across two Windows machines and a Mac, so it's neither machine-specific nor at the app or OS level. Comcast claims it's nothing to do with them, and my Linksys/Cisco RV016 router is out of warranty, so I have no access to official support. When I log into my router, it shows no error packets or dropped packets received. I plugged a laptop directly into the router and was able to download a 5.5 MB file and verify its MD5 hash, which is not proof that the problem is downstream of the router, but makes it seem quite likely, since I failed to download the same file several times from two desktops (one Mac, one Windows). Could this be a wiring problem? If so, is there any way clever/elegant to determine which wiring is faulty with just software? If I can avoid tracing all the wires throughout my entire house it would make my life quite a bit easier.

  Read the article

• Building new computer, turns on, but no post

  - by addybojangles

  Pardon my ignorance here, finally decided to put together a computer and egads. I purchased a new motherboard, power supply, processor, video card and memory. ASUS M4A79XTD EVO AM3 AMD 790X ATX AMD Motherboard OCZ Fatal1ty OCZ550FTY 550W ATX12V v2.2 / EPS12V SLI Ready 80 PLUS Certified Modular Active PFC Power Supply AMD Phenom II X4 965 Black Edition Deneb 3.4GHz 4 x 512KB L2 Cache 6MB L3 Cache Socket AM3 125W Quad-Core Processor XFX HD-577A-ZNFC Radeon HD 5770 (Juniper XT) 1GB 128-bit GDDR5 PCI Express 2.0 x16 HDCP Ready CrossFireX Support Video Card G.SKILL 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Dual Channel Kit Desktop Memory Model F3-12800CL9D-4GBNQ (originally had links for you guys, but I lack the rep, sorry!!) And I've got it all in the tower. I put in power supply, installed processor on motherboard, installed heatsink, put in ram, and I am using an older IDE hard disk. When I start the computer, the monitor tells me "check signal cable." As far as I can tell, the heatsink on the processor is spinning, the power supply is on (obviously), and the green LED on the motherboard is on. I originally only had the bigger output plugged in to the motherboard (what I saw in a YouTube vid as well as the mobo instructions), but after doing some research, it said plug in the other ATX power supply. Which I did. And trying to power the computer results in nothing. No beeps on startup, no post, anyone have any ideas? Your ideas and help is greatly appreciated.

  Read the article

• Digital Asset Management, iPhoto / Aperture server... alternative

  - by Sisyphus

  Afternoon, Clients, 10 : All Apples running either Leopard or Snow Leopard Server : Snow Leopard server, (and I have a old Dell Poweredge 650 at home running Gentoo 2.6, if anybody as a Linux solution). The situation: I work in small design company with 8 people, at present we are looking to consolidate all our image files onto one location, at present we each use our preferred single user DAM solution, be it, Adobe Bridge, iPhoto/Aperture (some don't bother at all) The filetypes commonly used are .psd, .pdf, .eps, .tiff, .jpg and RAW image files. Ideally what is needed: Centralised on one server, but allows us to search via spotlight (not essential, but would be nice) Include searchable metadata information such as date, location, title Open-source or as low cost as possibly Allow simultaneous users to import files So far, I have looked at a few open source DAM, systems, such as Razuna, Gallery (not strictly DAM), ResourceSpace, Notre-DAM, while these are brilliant and open-source, they don't integrate as smoothly with the Desktop as iPhoto and aperture. For iPhoto and aperture, I have tried creating a Shared library on the server (a tad laggy), and also using a drive with no permissions, put a library and letting each client read from it, however if they want to put images onto the library only, it's only supports one user at a time writing to the library... Any ideas what could fulfill our needs? Or is it time to bite the bullet for FinalCut Server? Thanks in advance.

  Read the article

• Play audio over network with Windows 7?

  - by Josh

  I have a unique situation where I'd like to stream audio (ALL audio, not just mp3s, etc) from my laptop to another computer over the network. I live in a studio apartment and my laptop is my main computer but I'd like it's audio to play on my htpc with a nice stereo system. Since it's a studio, both computers are in the same room so I don't want 2 sets of speakers. I want my computer to directly play back through the stereo. I used to do this with pulseaudio but my job now requires that I run Windows full time. I'm aware of Shoutcast and other similar streaming solutions but I don't want any transcoding done. It's a waste of CPU and not to mention my laptop fans, and I don't mind the network bandwidth that uncompressed audio requires. Is there a way to run Shoutcast without encoding? Also, I know that Windows Remote Desktop can play audio over the network pretty easily. Is this part of .Net that I could just code a simple app that streams the audio without RD'ing in? I also don't want to run it over a physical wire. :)

  Read the article

• Can't connect to a Hyper-V VM from anywhere but the host OS

  - by Elbelcho

  I have an unusual situation on hand where I'm able to connect to a Hyper-V guest VM from the HOST, but not from anywhere but the host. The VM is running WIn2k8R2 and has IIS installed and Remote Desktop enabled. If I browse to the IP from the host OS, the IIS7 page displays. I can also RDP into the guest OS from the host as well as ping. From OFF the host, RDP, web and ping all fail. If I completely shut off the guest VM's firewall, ping will then start to respond, but all RDP and port 80 still don't. The physical host machine has 2 nics installed, but only one is plugged in. The one plugged in has a static IP. I have one Hyper-V virtual network and it's set to external. The guest VM has one NIC with a different static IP than the host, but both are on the same subnet. The host machine is joined to the domain, the guest VM is not. Any sugestions? Thanks so much for any help you may be able to provide!

  Read the article

• Not recognizing second monitor after hibernate (Windows 7, Dell D630 laptop)

  - by Brooks Moses

  I have a Dell Latitude D630 laptop which I've recently updated to Windows 7 64-bit. (The Dell site confirms that it's Windows-7-compatible.) Normally it lives in a docking station with a second monitor connected to the DVI port on the docking station, and I use the second monitor in a multi-monitor configuration with the laptop screen. Sometimes I undock the laptop and use it separately. Here's the problem: If I hibernate the laptop while undocked, and then power it back up in the docking station, it does not recognize the second monitor. By which I mean that not only does it not share the desktop onto the second monitor, but if I go into the control panel for display settings and press "Detect", it does not even detect the existence of the second monitor. I can tell it to "use the VGA port anyway" for a second monitor, but the monitor is connected to a DVI port on the docking station, so that doesn't do anything useful. If I entirely reboot the laptop while it's connected to the docking station, it has no problem recognizing the second monitor and using it. But then, if I hibernate, undock, de-hibernate while undocked and rehibernate, and then re-dock and de-hibernate, it's back to not recognizing the second monitor again. I'm reasonably certain that this is not a limitation of the hardware; this worked fine on Windows XP. I'm currently using the Windows 7 driver for my video card. I attempted to use the video driver from the Dell website for this laptop, but Dell only provides Vista 64-bit drivers, not Windows 7 64-bit drivers. Their "Windows 7 compatibility" page suggests that the Vista drivers should work, but when I attempted to install the driver, it gave me a "this operating system not supported" error and refused to install. Any further ideas?

  Read the article

• How does enterprise failover, such as with google.com, actually work?

  - by Alex Regan

  We have a few fedora systems that are configured for web, FTP, and email services. We'd like to mirror these services, so that we can provide near 100% reliability for our users. I'm a fairly experienced Linux administrator, but don't have much experience with redundant systems. What is the best way to do this? How does google and amazon do it? Google.com resolves to multiple IP addresses, but if my local desktop caches one of the IPs that are unreachable, I'm going to get a failed connection message. How do they prevent that from happening? If one of their servers goes down, how is it automatically redirected to another system, without the end-user ever knowing it? I understand there are failover devices, but they're only for failing over the system itself, not a complete network. Let's say we have the worst-case scenario, such as my primary system becomes inaccessible. What are the fundamental components that are used on Linux systems to provide this capability? I'm looking for concepts, or approaches, not answers like "check out openstack". What are the actual pieces that make up the solution? What has to be done to implement this capability? Hopefully my question is clear. I'd like to know what the pieces are that make up a failover system and what approach is taken by successful organizations that implement it. Thanks again, Alex

  Read the article

• What's hogging my CPU?

  - by endolith

  Ubuntu's System Monitor applet shows 100% CPU usage continuously. If I click it, the resources tab shows it at 100% continuously, too. If I go to processes, though, to find out which process is the culprit, there is nothing above 10%. If I run top there is nothing above 10%. I try killing lots of things, but it continues at 100%. How can I find out what's hogging the CPU? This is an unusual situation on a computer I use daily, that normally only hits 100% CPU when I'm doing something that requires it (like loading 32 Firefox tabs) after which it goes back to a normal idle level. It's not a new install or anything. It shouldn't be maxed out. I'm not sure when it started or if I changed something that caused it to happen. Normally I would use top or System Monitor and find the process that had gone out of control, but I can't find anything with those tools this time. It persists after reboots and everything. And the processor is obviously hot, so it's not an erroneous reading. Update: I tried killing any process I saw active again, and killing vino-server finally fixed the problem, even though it never went above 5%. I had enabled Remote Desktop a few days ago (and have obviously now disabled it). How did it manage to use 100% CPU while top only showed it as 5% or so? How do I identify the culprit in the future? Looks like I'm not the only one: Still a problem in both jaunty & karmic. Interestingly, both System Monitor & htop do not show the sum of individual processes being anywhere near 100% cpu.

  Read the article

• Laptop choice for development: MacBook Pro 17 vs Dell Studio XPS 16 vs HP Envy 15

  - by Shalan

  Hey! First things first - let me state that I am not intending to play games on this - I have narrowed down to these 3 purely based on specs and its individual brand reliability in the market. I intend to primarily use: Visual Studio 2008 Pro a lot (develop and deploy on Windows platforms) SQL Server 2005 Oracle 10g Adobe Photoshop CS4 Microsoft Expression Studio Google Sketchup I currently use a desktop PC (Core2Duo 2.66Ghz with 3GB DDRII memory) running Vista Business 32-bit - and I have to admit that, especially for Visual Studio, its quite sluggish to a point where it affects productivity. Furthermore, I intend to only use the notebook on a table - with a cooled surface, like granite :) - so I would appreciate people's input with regard to heat issues. Im aware that the Dell's primary exhaust gets blocked by the lid when open, but some reviews don't seem to place extraordinary emphasis on heat issues resulting from this. My options for the Dell/Alienware: Core i7 720QM 4GB DDRIII memory ATI mobility 3670 (512) 128GB Solid State Drive 16-inch Full HD RGB-LED LCD display (1080p) 3-year next-business-day support My configuration for the Apple MBP: Core2Duo 2.8Ghz (Im assuming the T9600) 4GB DDRIII memory 128GB Solid State Drive standard 1 year support The one advantage I think of with the MBP is that I can have the addition of OSX (though Im unsure what I would use it for, but purely to play around with a much-boasted-about OS) What are your thoughts on this, especially regarding build-quality, heat, performance and battery-life? Much thanks! ~shalan

  Read the article

• Monitor connected with WiDi just shows a black screen

  - by Pops

  I have a Dell XPS 18 and want to use an external monitor with it. The monitor has VGA and DVI-D inputs. The XPS 18 has no video output ports, but it does support Intel WiDi. I have a Netgear P2TV2000 WiDi receiver, but it only has composite and HDMI outputs. I'm connecting the receiver to the monitor with an HDMI cable and an HDMI/DVI-D adapter. So, in short, the video path is: Computer → WiDi → WiDi receiver → HDMI cable → HDMI/DVI-D adapter → Monitor After setting all this up, I can't get anything to display on the monitor. At the moment I power the monitor on, I can see my desktop for a brief fraction of a second, and then everything goes black. All of the relevant drivers have been updated to the latest versions. When I use a different WiDi-enabled computer to connect to the same monitor, everything works fine. When I use the original computer and receiver to connect to a TV, everything works fine. It's only when I connect the original computer to the monitor I want to use that the connection fails. What could be going wrong here, and how can I get the video to work consistently?

  Read the article

• RTL8192SU Linux Issue Installing Driver

  - by s32ialx

  OK I've read tons of fourms of people getting the onboard RTL8192SE working and the RTL8192SU working dif is U = USB they are both N and i have both Toshiba L500D-00T pre-installed Win Vistax64-HP and i have obtained the free Win7x64-HP upgrade the onboard wificard sucks and can't hold a stable connection for more then 20minutes in windows but the usb is amazing. Now problem is i tried both Ubuntu and Mandriva with no resolve the issue is the onboard drive detects and actually SHOWS that it's there but no wireless networks detect so it's saying no SSID's are broadcasting which i know is a lie since I'm running a 2wire bell dsl modem with built in wifi and a Linksys wrt54g w/ DD-WRT firmware and both are broadcasting fine. Why don't i use the USB? In the hardware device manager in mandriva it shows up as unknown but shows that it's realtek and that it's a 8192 chipset. but no option to for a driver install and when i do a make in terminal i get this error and no clue what it means [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# make make: *** /lib/modules/2.6.31.12-desktop-3mnb/build: No such file or directory. Stop. make: *** [all] Error 2 [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# any help appreciated. and just encase I'm running currently Mandriva Spring 2010 Free

  Read the article

• Windows Server 2008 R2 SP1 Drivers Missing Would Not Install?

  - by bleepzter

  I am building my dev machine with WS2008R2SP1. I consider Windows Server as the best development environment for C# since I tend to focus on server-centric (integration) applications. The desktop flavor of Windows (7) doesn't play nicely with things like Commerce Server or BizTalk... so I to like stick to the environment I develop for. Previously I used to develop inside of VM's but I've found that it is super inefficient and tends to take a toll on the laptops. (I've gone through two of them in 6 months). Problem is that I multiple devices that do not want to be recognized by Windows: My machine is Dell Precision M4500: Intel Core i7-Q740, 1TB HDD, 8GB RAM, Dell re-branded Broadcom DW1501 802x11n Half-Mini Card, Dell re-branded Broadcom DW375 Bluetooh Module, Intel 82577LM Gigabit Network connection NVidia Quadro FX1800 Graphics The devices in question are the Dell rebranded broadcom network and bluetooth adapters: Broadcom USH: USB\VID_0A5C&PID_5800&REV_0101&MI_00 USB\VID_0A5C&PID_5800&MI_00 DW375 Bluetooth Module USB\VID_413C&PID_8187&REV_0517 USB\VID_413C&PID_8187 When I ran the broadcom installers I get "Operating System not supported" which I think is a big oversight on Broadcom's part. Why check for system version string? UGHGHGH Moreover if I try to manually force the driver in windows... I get an error: Driver Management concluded the process to install driver FileRepository\btwampsecfl.inf_amd64_neutral_d8fc2b85d035ed47\btwampsecfl.inf for Device Instance ID USB\VID_0A5C&PID_5800&MI_00\7&66DE6C9&0&0000 with the following status: 0xe0000217. '- or - Driver Management concluded the process to install driver FileRepository\btwampfl.inf_amd64_neutral_d4c4acf036c61299\btwampfl.inf for Device Instance ID USB\VID_413C&PID_8187\90004EEEF5A6 with the following status: 0xe0000217. I googled the 0xe0000217 error code and it says Bad service install section in the driver inf file... Any ideas on how to fix this? I also tried the post by BetaIQ on MSDN Forum, unfortunately the links to the driver package included in the post were dead :( PS. On a side note I also do mobile development for Android, iOS, and Windows Phone, and BB. Having the bluetooth is quite useful with mobile devices.

  Read the article

• How to multiseat with HW 3d accel on CentOS 6.3 Final?

  - by user35070

  I would like to setup a multiseat configuration on CentOS 6.3 (two video cards, two keyboards, two mice, two monitors) and have hardware accelerated 3D on both monitors. 3D HW acceleration rules out Xephyr. I saw somewhere that recent versions of GDM (3.3 and newer?) don't support multiseat, so do I have to install KDM to make this work? If I just create a duplicate section with new device identifiers in my xorg.conf file, will this 'just work'? Using different ports on the same video card and separate keyboards, mice, and displays, the result was a desktop which spanned both monitors with both keyboards and mice acting as the same input in the GUI. I will power down and put in the new video card and report on the results soon. Both video cards are nvidia. UPDATE after putting in another NVIDIA video card, default behavior (before changing xorg.conf) is that one screen works normally, and both mice and keyboards are connected to it. Changing xorg.conf and the display manager to KDM and following the directions here https://help.ubuntu.com/community/MultiseatX#Ubuntu_10.04_.28Lucid.29 , I have 2 mirrored screens connected to separate video cards, DRI enabled, and 2 mice both connected to the same pointer. Keyboards don't do anything, however, I probably just need to fix a setting in xorg.conf I would still like to get multiseat functionality, eg. separate screens with separate input devices I have verified that the separate X processes are running (see page above) using 'ps aux | grepX [01]'

  Read the article

• Linksys/Cisco Small Business SRW-Series (ie SRW248G4) - Overcoming the Limitations

  - by Warren P

  We just purchased a Cisco/Linksys SRW 248G4 switch to try it out. We have always had unmanaged switches before, and this is our first "somewhat managed" switch. So far the major limitations are: Only Internet Explorer 6 (manual says IE 5.5!) works for the web interface SSH exists but is not practically useable because the only key length that is supported is no longer even used by most modern SSH installs. (I get the error "RSA modulus too small" in openssh 4.x/5.x) This is with the latest firmware revision, I believe, although Cisco's website does not actually tell you what version you're downloading. All in all, I think, they must be trying to tell me that if I want a good-quality switch, I shouldn't buy these SRWs and should buy a Dell or an HP ProCurve, or save up my pennies, and buy a Catalyst. The question here, then, at long last: Has anyone gotten the web-browser to work via some IE 7 or IE 8 compatibility mode settings or used another browser (Opera? KDE/Safari/WebKit?) and spoofed IE6? Is there any way to get the SSH key length upgraded? I'm guessing a 0% chance of a yes on that last one. I found an XP machine, used telnet (via PuttyTel.exe) and IE6 to set this up, and I doubt we'll have to touch it again. Which is fine with us. But it would be nice if I could administer this thing from either (a) a linux box, or (b) my primary desktop which is windows 7. It looks like XPMode with IE6 on the virtual XP machine may be my only way to administer this type of switch via the web.

  Read the article

• Free or Open Solution for Storing and Charting CSV data

  - by rrrfusco

  I'm presently storing CSV files, combining them, opening them in open office, creating pivot tables and then generating charts from the spreadsheet. I've looked at OOBase, but appending csv files to base is clunky for some reason. SQLite seems like a good database solution, but I've haven't found a good charting program that connects to it with ease. Although open office (or libreoffice) maintains the references and allows you to update the information, this process is far from efficient. There are too many steps and it seems one program should handle all of these tasks. A better program would be more intuitive, allow you to simply add inserts into a database, and include an interface for standard charting settings. EDIT Simplest Automated Analysis and Chart Generation Tool? The above answer references Spotfire and Tableau, each of which has a free 14 and 30 day trial. Each program is nicely streamlined and designed. I'm looking for a program between this quality and LibreOffice. Can you recommend a better open or free desktop solution for windows?

  Read the article

• Unable To Successfully Use Java Anywhere (Windows 7 64bit)

  - by Nathan Smith

  This is a bit of an odd issue: (This is with JRE 7u7 32bit.) New Lenovo W530 laptop, everything is shiny. I tried to use a java applet for the first time recently (in Chrome). I got the Java logo and it started spinning like it was going to load, but didn't get anywhere and the browser locked up. I tried IE. Same deal. Tried Firefox. Same deal. So, I did the usual things: Rebooted, nothing. Un-installed Java, rebooted, re-installed, nothing. Tried it installing a 64bit Java as well. Same thing. I tried JRE6. Same thing. I uninstalled and manually deleted all the registry entries I could find related to it, then re-installed. Same thing. I un-installed and used the JavaRa utility. Same exact thing. I've not been able to use web applets or desktop stuff (minecraft), until yesterday. I did a graphics driver update and I was able to play minecraft for small amounts of time. It crashed regularly and wouldn't start reliably. No change in web applets. I'm at my wits end here. I'm to the point where reformatting is my only option. If anyone has any ideas at all, that would be awesome.

  Read the article

• what's the difference between a Volume and a Partition in Windows 7 diskpart

  - by user170232

  I was trying to follow the Intel guide for setting up iRST (Intel Rapid Start Technology) on my new laptop. The Intel manual says you need to create a *Volume that is as big or bigger than your available memory, set it to a specific id (id=84), then go into the iRST tool and adjust some settings. Looking at the disk manager on the laptop, I see there is already a Partition labeled as "Hibernation Partition" which is a little bigger than the memory in my system. So it looks like iRST was already set up...BUT, it's a Partition, not a Volume. Here's what the manual says to do: (from: http://download.intel.com/support/motherboards/desktop/sb/rapid_start_technology_user_guide.pdf) diskpart list disk select disk x (where x is the disk to use, there's only one disk in this laptop) create partition primary size=X000 (where X000 is the size to create) detail disk (which lists details for the disk. This is where i get hung up) select volume Z (where Z is the *partition you created previously) ** it says the 'detail disk' command will list the volume #, but it doesn't. ** 'detail disk' only lists two "volumes" for Recovery and OS. ** if i do 'list partition', i see the 8 GB *partition labeled as "Hibernation Partition") ** so I can't continue with the following steps: set id=84 override exit The reason I went looking for the manual is because when iRST is enabled in the BIOS, the system won't resume from sleep. When it's disabled, it works fine, but the system goes into (legacy?) Hibernation mode and takes a while to come out of Hibernation. the iRST is supposed to resume from deep sleep very quickly. So, what's the difference between a Volume and a Partition? Should I delete the Hibernation Partition and create a Hibernation Volume? Anyone have any ideas? (if it matters, this is on a Dell XPS 13 with BIOS A08) Thanks! J

  Read the article

• problem booting crusty old windows XP

  - by Carson Myers

  I have an acer aspire laptop running Windows XP home. I believe I have some virus on it, I'm not sure--I mostly just run linux in a VM on it so I wasn't too worried. I'm not sure if that virus caused this problem. The laptop wasn't recognizing my USB hard drive for some reason so I decided to restart it. When it started up, it got past the memory test, past the boot screen, (but it paused right here on a blank screen for awhile) and flashed the desktop once (like it does just before the login screen) and then crashed. I got a quick BSOD and then it restarted. Then it tried to boot again, etc etc infinite loop of failure. Well, before trying safe mode, I disabled automatic restart on system crash so I could read the blue screen. There wasn't anything important on it, it said *** STOP: 0x00000000 (0xC0000000 0x,.... ) beginning physical memory dump physical memory dump complete That's not verbatim (obviously) but it didn't help me. so I booted in safe mode, and it stopped on the driver gagp30kx.sys and then restarted (and infinite loop of failure again). I burned a recovery CD and tried that. It loaded it, and I went into repair mode. I ran chkdsk and then disabled the AGP driver. Same thing on booting in safe mode except it stopped at mup.sys instead. I enabled the AGP driver again, and ran chkdsk again from the CD. It said it found problems but didn't say it fixed them. So I ran it a second time, and it said "performing additional checking or recovery" lots of times (I can't tell how many, they went above the screen top). I tried booting again and no luck. Every time I run chkdsk after trying to boot again it says it found and fixed more errors. I think it might be whatever driver is after the AGP driver, but I don't know what it is or how to find out. Can anyone help me fix this?

  Read the article

• Acer Aspire One getting extremely hot

  - by ascom

  I have an Acer Aspire One D250-1197. I really better type fast before it overheats again... For some reason, I'm having a problem with heat on my netbook only when I run Joli OS (Ubuntu 9.10 LTS?). When I leave it idle, with nothing running (other than the regular Joli OS desktop and a couple of doing-nothing terminals), heat slowly builds up to the point where the netbook is burning hot to the touch. I have never had this problem when running Windows 7 Starter (even though it gives me plenty of other headaches). It seems that the fan is spinning, but not fast enough to keep up with the heat buildup. Is there something wrong with the fan drivers? The computer doesn't seem to recognize that it is overheating. What can I do to solve this problem (other than shut it off or use Windows)? I'm currently on the wrong side of Earth (I mean, on vacation), so I just need a temporary fix, such as a driver I can install. Also, I have to use Linux, because I have to share out the wired connection in hotels wirelessly to the iPhones. EDIT: I'm switching from Joli OS to a more "proper" and up to date distribution (Xubuntu 13.04). I'll see if it still has the heat problem and try @nod's cpufreq idea.

  Read the article

• Can't find disk usage in one directory

  - by Xster

  Similar questions are asked frequently but no suggested answers solved my issue. I have some disk space usage that I can't find as well. In df Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda1 144183992 136857180 2652 100% / udev 2013316 4 2013312 1% /dev tmpfs 808848 876 807972 1% /run none 5120 0 5120 0% /run/lock none 2022116 76 2022040 1% /run/shm overflow 1024 0 1024 0% /tmp I checked the inodes, I checked lsof for +L1 or deleted files, I rebooted, I checked for files hidden behind mounts but none of them were the issue. It grows periodically and I'm running out of things to delete to feed the beast. It's all in the home directory of the only user I have. In du in ~ du -h --max-depth=1 192K ./.nv 2.1M ./.gconf 12K ./Pictures 1.6M ./.launchpadlib 12K ./Public 24K ./.TemporaryItems 8.9M ./.cache 12K ./Network Trash Folder 28K ./.vnc 11M ./.AppleDB 48K ./.subversion 1.9G ./.xbmc 8.0K ./.AppleDesktop 12K ./.dbus 81M ./.mozilla 12K ./Music 160K ./.gnome2 44K ./Downloads 692K ./.zsh 236K ./.AppleDouble 64K ./.pulse 4.0K ./.gvfs 1.4M ./.adobe 44K ./.pki 44K ./.compiz-1 168K ./.config 1.4M ./.thumbnails 12K ./Templates 912K ./.gstreamer-0.10 8.0K ./.emacs.d 92K ./Desktop 1.3M ./.local 12K ./Ubuntu One 12K ./Documents 296K ./.fontconfig 12K ./.qt 12K ./.gnome2_private 20K ./.ssh 20K ./.mission-control 12K ./Videos 12K ./Temporary Items 640K ./.macromedia 124G . I can't find a way to figure out how it got to that 124G in that directory. There are no mount points in home.

  Read the article

• Intel z77 vs h77 for intensive compiling, gaming [closed]

  - by Bilal Akhtar

  I'm in the market for a desktop motherboard (preferably ATX) that functions well with Intel i7-3770 Ivy Bridge processor at 3.4 GHz with LGA1155 socket. That processor is very fast, and it should handle all my tasks. My question is about the type of motherboard chipset I should choose to accompany it. I plan to use my rig for compiling and developing Debian package and other OS components, web development, occasional Android apps, chroots, VMs, FlightGear, other gaming but nothing serious, and heavy multitasking, all on Ubuntu. I do NOT plan to overclock, and I never will, so that's not a cause of concern for me. That said, I'm down to three chipset choices: Intel H77 Intel Z68 Intel Z77 I'm planning to go for H77 since I don't need any of the new features in Z77. I don't plan to use a second GPU and I will never overclock my CPU/GPU. My question is, will H77 based MoBos handle all my tasks well? Intel advertises that chipset as "everyday computing" but other sites say it's base functionality is the same as Z77. Intel rather advertises Z77 for "serious multitaskers, hardcore gamers and overclocking enthusiasts". But the problem with all Z77 motherboards I've seen is, they're way too expensive and their main feature seems to be overclocking, which won't be useful to me. Will I lose any raw CPU/GPU performance or HDD R/w with the H77 when comparing it to a Z77? Will heat, etc be an issue too? From what I've seen, Z77 motherboards have larger heat sinks when compared to H77 ones. Will that be an issue too, if I go with an H77 motherboard with no heat sinks for the chipset? The CPU will have a fan in both cases, of course. tl;dr When it comes to CPU/GPU performance and HDD r/w, is the Intel H77 chipset slower than the Z77? I don't care about overclocking or multiple GPUs, and for the processor, I'm set on Ivy Bridge i7-3770.

  Read the article

< Previous Page | 445 446 447 448 449 450 451 452 453 454 455 456  | Next Page >