Search Results

Search found 22641 results on 906 pages for 'visual studio express 200'.

Page 450/906 | < Previous Page | 446 447 448 449 450 451 452 453 454 455 456 457  | Next Page >

• Linux e1000e (Intel networking driver) problems galore, where do I start?

  - by Evan Carroll

  I'm currently having a major problem with e1000e (not working at all) in Ubuntu Maverick (1.0.2-k4), after resume I'm getting a lot of stuff in dmesg: [ 9085.820197] e1000e 0000:02:00.0: PCI INT A disabled [ 9089.907756] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k4 [ 9089.907762] e1000e: Copyright (c) 1999 - 2009 Intel Corporation. [ 9089.907797] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9089.907827] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9089.907857] e1000e 0000:02:00.0: setting latency timer to 64 [ 9089.908529] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9089.908922] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9089.908954] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9090.024625] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9090.024630] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9090.024712] e1000e 0000:02:00.0: eth0: MAC: 2, PHY: 2, PBA No: 005302-003 [ 9090.109492] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9090.164219] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X and, a bunch of [ 2128.005447] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang: [ 2128.005452] TDH <89> [ 2128.005454] TDT <27> [ 2128.005456] next_to_use <27> [ 2128.005458] next_to_clean <88> [ 2128.005460] buffer_info[next_to_clean]: [ 2128.005463] time_stamp <6e608> [ 2128.005465] next_to_watch <8a> [ 2128.005467] jiffies <6f929> [ 2128.005469] next_to_watch.status <0> [ 2128.005471] MAC Status <80080703> [ 2128.005473] PHY Status <796d> [ 2128.005475] PHY 1000BASE-T Status <4000> [ 2128.005477] PHY Extended Status <3000> [ 2128.005480] PCI Status <10> I decided to compile the latest stable e1000e to 1.2.17, now I'm getting: [ 9895.678050] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.17-NAPI [ 9895.678055] e1000e: Copyright(c) 1999 - 2010 Intel Corporation. [ 9895.678098] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9895.678129] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9895.678162] e1000e 0000:02:00.0: setting latency timer to 64 [ 9895.679136] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.679160] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9895.679192] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9895.791758] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9895.791766] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9895.791850] e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 2, PBA No: 005302-003 [ 9895.892464] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.948175] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.949111] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9895.954694] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: RX/TX [ 9895.954703] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO [ 9895.955157] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9906.832056] eth0: no IPv6 routers present With 1.2.20 I get: [ 9711.525465] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.20-NAPI [ 9711.525472] e1000e: Copyright(c) 1999 - 2010 Intel Corporation. [ 9711.525521] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9711.525554] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9711.525586] e1000e 0000:02:00.0: setting latency timer to 64 [ 9711.526460] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9711.526487] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9711.526523] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9711.639763] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9711.639771] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9711.639854] e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 2, PBA No: 005302-003 [ 9712.060770] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9712.116195] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9712.117098] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9712.122684] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX [ 9712.122693] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO [ 9712.123142] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9722.920014] eth0: no IPv6 routers present But, I'm still getting these [ 9982.992851] PCI Status <10> [ 9984.993602] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang: [ 9984.993606] TDH <5d> [ 9984.993608] TDT <6b> [ 9984.993611] next_to_use <6b> [ 9984.993613] next_to_clean <5b> [ 9984.993615] buffer_info[next_to_clean]: [ 9984.993617] time_stamp <24da80> [ 9984.993619] next_to_watch <5d> [ 9984.993621] jiffies <24f200> [ 9984.993624] next_to_watch.status <0> [ 9984.993626] MAC Status <80080703> [ 9984.993628] PHY Status <796d> [ 9984.993630] PHY 1000BASE-T Status <4000> [ 9984.993632] PHY Extended Status <3000> [ 9984.993635] PCI Status <10> [ 9986.001047] e1000e 0000:02:00.0: eth0: Reset adapter [ 9986.176202] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: RX/TX [ 9986.176211] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO I'm not sure where to start troubleshooting this. Any ideas? Here is the result of ethtool -d eth0 MAC Registers ------------- 0x00000: CTRL (Device control register) 0x18100248 Endian mode (buffers): little Link reset: reset Set link up: 1 Invert Loss-Of-Signal: no Receive flow control: enabled Transmit flow control: enabled VLAN mode: disabled Auto speed detect: disabled Speed select: 1000Mb/s Force speed: no Force duplex: no 0x00008: STATUS (Device status register) 0x80080703 Duplex: full Link up: link config TBI mode: disabled Link speed: 10Mb/s Bus type: PCI Express Port number: 0 0x00100: RCTL (Receive control register) 0x04048002 Receiver: enabled Store bad packets: disabled Unicast promiscuous: disabled Multicast promiscuous: disabled Long packet: disabled Descriptor minimum threshold size: 1/2 Broadcast accept mode: accept VLAN filter: enabled Canonical form indicator: disabled Discard pause frames: filtered Pass MAC control frames: don't pass Receive buffer size: 2048 0x02808: RDLEN (Receive desc length) 0x00001000 0x02810: RDH (Receive desc head) 0x00000001 0x02818: RDT (Receive desc tail) 0x000000F0 0x02820: RDTR (Receive delay timer) 0x00000000 0x00400: TCTL (Transmit ctrl register) 0x3103F0FA Transmitter: enabled Pad short packets: enabled Software XOFF Transmission: disabled Re-transmit on late collision: enabled 0x03808: TDLEN (Transmit desc length) 0x00001000 0x03810: TDH (Transmit desc head) 0x00000000 0x03818: TDT (Transmit desc tail) 0x00000000 0x03820: TIDV (Transmit delay timer) 0x00000008 PHY type: IGP2 and ethtool -c eth0 Coalesce parameters for eth0: Adaptive RX: off TX: off stats-block-usecs: 0 sample-interval: 0 pkt-rate-low: 0 pkt-rate-high: 0 rx-usecs: 3 rx-frames: 0 rx-usecs-irq: 0 rx-frames-irq: 0 tx-usecs: 0 tx-frames: 0 tx-usecs-irq: 0 tx-frames-irq: 0 rx-usecs-low: 0 rx-frame-low: 0 tx-usecs-low: 0 tx-frame-low: 0 rx-usecs-high: 0 rx-frame-high: 0 tx-usecs-high: 0 tx-frame-high: 0 Here is also the lspci -vvv for this controller 02:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller Subsystem: Lenovo ThinkPad X60s Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 45 Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at 2000 [size=32] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0300c Data: 415a Capabilities: [e0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn- Capabilities: [140 v1] Device Serial Number 00-0a-e4-ff-ff-3e-ce-74 Kernel driver in use: e1000e Kernel modules: e1000e I filed a bug on this upstream, still no idea how to get more useful information. Here is a the result of the running that script EEPROM FIX UPDATE $ sudo bash fixeep-82573-dspd.sh eth0 eth0: is a "82573L Gigabit Ethernet Controller" This fixup is applicable to your hardware Your eeprom is up to date, no changes were made Do I still need to do anything? Also here is my EEPROM dump $ sudo ethtool -e eth0 Offset Values ------ ------ 0x0000 00 0a e4 3e ce 74 30 0b b2 ff 51 00 ff ff ff ff 0x0010 53 00 03 02 6b 02 7e 20 aa 17 9a 10 86 80 df 80 0x0020 00 00 00 20 54 7e 00 00 14 00 da 00 04 00 00 27 0x0030 c9 6c 50 31 3e 07 0b 04 8b 29 00 00 00 f0 02 0f 0x0040 08 10 00 00 04 0f ff 7f 01 4d ff ff ff ff ff ff 0x0050 14 00 1d 00 14 00 1d 00 af aa 1e 00 00 00 1d 00 0x0060 00 01 00 40 1f 12 07 40 ff ff ff ff ff ff ff ff 0x0070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff 4a e0 I'd also like to note that I used eth0 every day for years and until recently never had an issue.

  Read the article

• Sometimes this script fails to update the iptables

  - by AlJo

  It does not happen often, but sometimes after running the below script, checking the iptables with service iptables status shows that they weren't updated and the script doesn't output any error. The iptables is structured as look-up tree (long repeated sections snipped): #!/bin/sh iptables -t nat -F iptables -t nat -X iptables -F iptables -X iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -s 93.225.0.0/16 -j ACCEPT iptables -A INPUT -s 15.102.0.0/16 -j ACCEPT iptables -A INPUT -s 47.122.0.0/16 -j ACCEPT iptables -N MY_CHAIN_L1-0 iptables -N MY_CHAIN_L1-1 iptables -N MY_CHAIN_L1-2 iptables -N MY_CHAIN_L1-3 iptables -N MY_CHAIN_L1-4 iptables -N MY_CHAIN_L1-5 iptables -N MY_CHAIN_L1-6 iptables -N MY_CHAIN_L1-7 iptables -N MY_CHAIN_L1-8 iptables -N MY_CHAIN_L1-9 iptables -N MY_CHAIN_L1-10 iptables -N MY_CHAIN_L1-11 iptables -N MY_CHAIN_L1-12 iptables -N MY_CHAIN_L1-13 iptables -N MY_CHAIN_L1-14 iptables -N MY_CHAIN_L1-15 iptables -N MY_CHAIN_L1-16 iptables -N MY_CHAIN_L1-17 iptables -N MY_CHAIN_L1-18 iptables -N MY_CHAIN_L1-19 iptables -N MY_CHAIN_L1-20 iptables -N MY_CHAIN_L1-21 iptables -N MY_CHAIN_L1-22 iptables -N MY_CHAIN_L1-23 iptables -N MY_CHAIN_L1-24 iptables -N MY_CHAIN_L1-25 iptables -N MY_CHAIN_L1-26 iptables -N MY_CHAIN_L1-27 iptables -N MY_CHAIN_L1-28 iptables -N MY_CHAIN_L1-29 iptables -N MY_CHAIN_L1-30 iptables -N MY_CHAIN_L1-31 iptables -N MY_CHAIN_L1-32 iptables -N MY_CHAIN_L1-33 iptables -N MY_CHAIN_L1-34 iptables -N MY_CHAIN_L1-35 iptables -N MY_CHAIN_L1-36 iptables -N MY_CHAIN_L1-37 iptables -A INPUT -m iprange --src-range 1.54.96.0-5.133.179.255 -j MY_CHAIN_L1-0 iptables -A INPUT -m iprange --src-range 5.133.180.0-24.113.159.255 -j MY_CHAIN_L1-1 [snip] iptables -A INPUT -m iprange --src-range 195.13.45.0-198.11.255.255 -j MY_CHAIN_L1-29 iptables -A INPUT -m iprange --src-range 198.12.64.0-199.19.215.255 -j MY_CHAIN_L1-30 iptables -A INPUT -m iprange --src-range 199.21.96.0-200.31.3.255 -j MY_CHAIN_L1-31 iptables -A INPUT -m iprange --src-range 200.31.11.0-202.171.255.255 -j MY_CHAIN_L1-32 iptables -A INPUT -m iprange --src-range 203.130.134.192-206.212.255.255 -j MY_CHAIN_L1-33 iptables -A INPUT -m iprange --src-range 206.214.64.0-211.155.95.255 -j MY_CHAIN_L1-34 iptables -A INPUT -m iprange --src-range 212.19.128.0-216.176.191.255 -j MY_CHAIN_L1-35 iptables -A INPUT -m iprange --src-range 216.189.0.0-218.23.255.255 -j MY_CHAIN_L1-36 iptables -A INPUT -m iprange --src-range 218.30.96.0-223.255.231.255 -j MY_CHAIN_L1-37 iptables -A MY_CHAIN_L1-0 -s 1.54.96.0/20 -j DROP iptables -A MY_CHAIN_L1-0 -s 1.208.0.0/12 -j DROP iptables -A MY_CHAIN_L1-0 -s 1.224.0.0/11 -j DROP [snip] iptables -A MY_CHAIN_L1-0 -s 5.133.178.0/23 -j DROP iptables -A MY_CHAIN_L1-0 -j ACCEPT iptables -A MY_CHAIN_L1-1 -s 5.133.180.0/22 -j DROP iptables -A MY_CHAIN_L1-1 -s 5.135.0.0/16 -j DROP iptables -A MY_CHAIN_L1-1 -s 5.153.232.0/21 -j DROP [snip] iptables -A MY_CHAIN_L1-1 -s 24.113.128.0/19 -j DROP iptables -A MY_CHAIN_L1-1 -j ACCEPT . . . iptables -A MY_CHAIN_L1-29 -s 195.13.45.0/24 -j DROP iptables -A MY_CHAIN_L1-29 -s 195.20.224.0/19 -j DROP iptables -A MY_CHAIN_L1-29 -s 195.31.216.0/26 -j DROP iptables -A MY_CHAIN_L1-29 -s 195.58.245.0/24 -j DROP iptables -A MY_CHAIN_L1-29 -s 195.60.164.0/23 -j DROP iptables -A MY_CHAIN_L1-29 -s 195.60.240.0/22 -j DROP iptables -A MY_CHAIN_L1-29 -s 195.62.10.0/23 -j DROP iptables -A MY_CHAIN_L1-29 -s 195.110.30.0/23 -j DROP iptables -A MY_CHAIN_L1-29 -s 195.154.0.0/16 -j DROP iptables -A MY_CHAIN_L1-29 -s 195.190.13.0/24 -j DROP iptables -A MY_CHAIN_L1-29 -s 195.211.152.0/22 -j DROP iptables -A MY_CHAIN_L1-1 -j ACCEPT [snip more of same to end of script] Can anyone see why this script would silently fail to update the iptables sometimes? Maybe it's not the script? Thanks

  Read the article

• nginx: How can I set proxy_* directives only for matching URIs?

  - by Artem Russakovskii

  I've been at this for hours and I can't figure out a clean solution. Basically, I have an nginx proxy setup, which works really well, but I'd like to handle a few urls more manually. Specifically, there are 2-3 locations for which I'd like to set proxy_ignore_headers to Set-Cookie to force nginx to cache them (nginx doesn't cache responses with Set-Cookie as per http://wiki.nginx.org/HttpProxyModule#proxy_ignore_headers). So for these locations, all I'd like to do is set proxy_ignore_headers Set-Cookie; I've tried everything I could think of outside of setting up and duplicating every config value, but nothing works. I tried: Nesting location directives, hoping the inner location which matches on my files would just set this value and inherit the rest, but that wasn't the case - it seemed to ignore anything set in the outer location, most notably proxy_pass and I end up with a 404). Specifying the proxy_cache_valid directive in an if block that matches on $request_uri, but nginx complains that it's not allowed ("proxy_cache_valid" directive is not allowed here). Specifying a variable equal to "Set-Cookie" in an if block, and then trying to set proxy_cache_valid to that variable later, but nginx isn't allowing variables for this case and throws up. It should be so simple - modifying/appending a single directive for some requests, and yet I haven't been able to make nginx do that. What am I missing here? Is there at least a way to wrap common directives in a reusable block and have multiple location blocks refer to it, after adding their own unique bits? Thank you. Just for reference, the main location / block is included below, together with my failed proxy_ignore_headers directive for a specific URI. location / { # Setup var defaults set $no_cache ""; # If non GET/HEAD, don't cache & mark user as uncacheable for 1 second via cookie if ($request_method !~ ^(GET|HEAD)$) { set $no_cache "1"; } if ($http_user_agent ~* '(iphone|ipod|ipad|aspen|incognito|webmate|android|dream|cupcake|froyo|blackberry|webos|s8000|bada)') { set $mobile_request '1'; set $no_cache "1"; } # feed crawlers, don't want these to get stuck with a cached version, especially if it caches a 302 back to themselves (infinite loop) if ($http_user_agent ~* '(FeedBurner|FeedValidator|MediafedMetrics)') { set $no_cache "1"; } # Drop no cache cookie if need be # (for some reason, add_header fails if included in prior if-block) if ($no_cache = "1") { add_header Set-Cookie "_mcnc=1; Max-Age=17; Path=/"; add_header X-Microcachable "0"; } # Bypass cache if no-cache cookie is set, these are absolutely critical for Wordpress installations that don't use JS comments if ($http_cookie ~* "(_mcnc|comment_author_|wordpress_(?!test_cookie)|wp-postpass_)") { set $no_cache "1"; } if ($request_uri ~* wpsf-(img|js)\.php) { proxy_ignore_headers Set-Cookie; } # Bypass cache if flag is set proxy_no_cache $no_cache; proxy_cache_bypass $no_cache; # under no circumstances should there ever be a retry of a POST request, or any other request for that matter proxy_next_upstream off; proxy_read_timeout 86400s; # Point nginx to the real app/web server proxy_pass http://localhost; # Set cache zone proxy_cache microcache; # Set cache key to include identifying components proxy_cache_key $scheme$host$request_method$request_uri$mobile_request; # Only cache valid HTTP 200 responses for this long proxy_cache_valid 200 15s; #proxy_cache_min_uses 3; # Serve from cache if currently refreshing proxy_cache_use_stale updating timeout; # Send appropriate headers through proxy_set_header Host $host; # no need for this proxy_set_header X-Real-IP $remote_addr; # no need for this proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; # Set files larger than 1M to stream rather than cache proxy_max_temp_file_size 1M; access_log /var/log/nginx/androidpolice-microcache.log custom; }

  Read the article

• 502 Bad Gateway - nginx

  - by ADH2

  I am randomly receiving 502 Bad Gateway error pages - I can reproduce this issue by modifying hosting plans in plesk 11 and in the same time refreshing a page for a minute or two. When I get the 502 error page all I have to do is refresh the browser and the page refreshes properly. i am using centos 6 this it from todays log (/var/log/nginx/error.log): 2012/12/04 10:52:07 [error] 21272#0: *545 recv() failed (104: Connection reset by peer) while reading response header from upstream, client: 82.77.68.111, server: likeit-craiova.ro, request: "GET / HTTP/1.1", upstream: "http://195.254.135.113:7080/", host: "likeit-craiova.ro" this is the nginx config (/etc/nginx/nginx.conf) #user nginx; worker_processes 1; #error_log /var/log/nginx/error.log; #error_log /var/log/nginx/error.log notice; #error_log /var/log/nginx/error.log info; #pid /var/run/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; proxy_buffer_size 128k; proxy_buffers 4 256k; proxy_busy_buffers_size 256k; #log_format main '$remote_addr - $remote_user [$time_local] "$request" ' # '$status $body_bytes_sent "$http_referer" ' # '"$http_user_agent" "$http_x_forwarded_for"'; #access_log /var/log/nginx/access.log main; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; #tcp_nodelay on; #gzip on; #gzip_disable "MSIE [1-6]\.(?!.*SV1)"; server_tokens off; include /etc/nginx/conf.d/*.conf; } fastcgi config file (/etc/nginx/fastcgi.conf): fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param HTTPS $https if_not_empty; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; # PHP only, required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; fastcgi parameters config (/etc/nginx/fastcgi_params): fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param HTTPS $https if_not_empty; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; # PHP only, required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; alsow i'm getting this on a shared hosting server, on one of the domains: Unable to generate the web server configuration file on the host because of the following errors: nginx: [warn] duplicate MIME type "text/html" in /etc/nginx/nginx.conf:45 nginx: [emerg] open() "/var/www/vhosts/partydayandnight.ro/statistics/logs/proxy_access_log" failed (24: Too many open files) nginx: configuration file /etc/nginx/nginx.conf test failed Please resolve the errors in web server configuration templates and generate the file again. why is this appearing and what troubles may it cause? what can i do to get this errors fixed? thank you!

  Read the article

• mono 3.0.2 + xsp + lighttpd delivers empty page

  - by Nefal Warnets

  I needed MVC 4 (and basic .NET 4.5) support so I downloaded mono 3.0.2 and deployed it on an lighttpd 1.4.28 installation, together with xsp-2.10.2 (was the latest I could find). After going through the config tutorials I managed to get the fastcgi server to spawn, but all pages are served empty. even if I go to nonexistant urls or direct .aspx files I get an empty HTTP 200 response. The log file on Debug shows nothing suspicious. Here is the log: [2012-12-12 15:15:38Z] Debug Accepting an incoming connection. [2012-12-12 15:15:38Z] Debug Record received. (Type: BeginRequest, ID: 1, Length: 8) [2012-12-12 15:15:38Z] Debug Record received. (Type: Params, ID: 1, Length: 801) [2012-12-12 15:15:38Z] Debug Record received. (Type: Params, ID: 1, Length: 0) [2012-12-12 15:15:38Z] Debug Read parameter. (SERVER_SOFTWARE = lighttpd/1.4.28) [2012-12-12 15:15:38Z] Debug Read parameter. (SERVER_NAME = xxxx) [2012-12-12 15:15:38Z] Debug Read parameter. (GATEWAY_INTERFACE = CGI/1.1) [2012-12-12 15:15:38Z] Debug Read parameter. (SERVER_PORT = 80) [2012-12-12 15:15:38Z] Debug Read parameter. (SERVER_ADDR = xxxx) [2012-12-12 15:15:38Z] Debug Read parameter. (REMOTE_PORT = xxx) [2012-12-12 15:15:38Z] Debug Read parameter. (REMOTE_ADDR = xxxx) [2012-12-12 15:15:38Z] Debug Read parameter. (SCRIPT_NAME = /ViewPage1.aspx) [2012-12-12 15:15:38Z] Debug Read parameter. (PATH_INFO = ) [2012-12-12 15:15:38Z] Debug Read parameter. (SCRIPT_FILENAME = /data/htdocs/ViewPage1.aspx) [2012-12-12 15:15:38Z] Debug Read parameter. (DOCUMENT_ROOT = /data/htdocs) [2012-12-12 15:15:38Z] Debug Read parameter. (REQUEST_URI = /ViewPage1.aspx) [2012-12-12 15:15:38Z] Debug Read parameter. (QUERY_STRING = ) [2012-12-12 15:15:38Z] Debug Read parameter. (REQUEST_METHOD = GET) [2012-12-12 15:15:38Z] Debug Read parameter. (REDIRECT_STATUS = 200) [2012-12-12 15:15:38Z] Debug Read parameter. (SERVER_PROTOCOL = HTTP/1.1) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_HOST = xxxxx) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_CONNECTION = keep-alive) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_CACHE_CONTROL = max-age=0) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_USER_AGENT = Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.11 (KHTML, like Gecko) Chrome/23.0.1271.95 Safari/537.11) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_ACCEPT = text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_ACCEPT_ENCODING = gzip,deflate,sdch) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_ACCEPT_LANGUAGE = en-US,en;q=0.8) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_ACCEPT_CHARSET = ISO-8859-1,utf-8;q=0.7,*;q=0.3) [2012-12-12 15:15:38Z] Debug Record received. (Type: StandardInput, ID: 1, Length: 0) [2012-12-12 15:15:38Z] Debug Record sent. (Type: EndRequest, ID: 1, Length: 8) lighttpd config: server.modules += ( "mod_fastcgi" ) include "conf.d/mono.conf" $HTTP["host"] !~ "^vdn\." { $HTTP["url"] !~ "\.(jpg|gif|png|js|css|swf|ico|jpeg|mp4|flv|zip|7z|rar|psd|pdf|html|htm)$" { fastcgi.server += ( "" => (( "socket" => mono_shared_dir + "fastcgi-mono-server", "bin-path" => mono_fastcgi_server, "bin-environment" => ( "PATH" => mono_dir + "bin:/bin:/usr/bin:", "LD_LIBRARY_PATH" => mono_dir + "lib:", "MONO_SHARED_DIR" => mono_shared_dir, "MONO_FCGI_LOGLEVELS" => "Debug", "MONO_FCGI_LOGFILE" => mono_shared_dir + "fastcgi.log", "MONO_FCGI_ROOT" => mono_fcgi_root, "MONO_FCGI_APPLICATIONS" => mono_fcgi_applications ), "max-procs" => 1, "check-local" => "disable" )) ) } } the referenced mono.conf index-file.names += ( "index.aspx", "default.aspx" ) var.mono_dir = "/usr/" var.mono_shared_dir = "/tmp/" var.mono_fastcgi_server = mono_dir + "bin/" + "fastcgi-mono-server4" var.mono_fcgi_root = server.document-root var.mono_fcgi_applications = "/:." The document root for this server is /data/htdocs. The asp.net files reside there. lighttpd error logs show nothing. Every help is greatly appreciated!

  Read the article

• sql server doesn’t exist or access denied

  - by kareemsaad

  I had Win7 in my pc and I installed 2vmware .One of them (VM) had Win XP and I installed on It SQL 2000 and visual studio 2008.and other I installed Win XP and I installed on it SQL 2005 and visual studio 2008. and when I run SQL2000 this error appear sql server doesn't exist or access denied Pleas verify sql server is running ........

  Read the article

• second ip address on the same interface but on a different subnet

  - by fptstl

  Is it possible in CentOS 5.7 64bit to have a second IP address on one interface (eg. eth0) - alias interface configuration - in a different subnet? Here is the original config for eth0 more etc/sysconfig/network-scripts/ifcfg-eth0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0 BOOTPROTO=static BROADCAST=192.168.91.255 HWADDR=00:1D:09:FE:DA:04 IPADDR=192.168.91.250 NETMASK=255.255.255.0 NETWORK=192.168.91.0 ONBOOT=yes And here is the config for eth0:0 more etc/sysconfig/network-scripts/ifcfg-eth0:0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0:0 BOOTPROTO=static BROADCAST=10.10.191.255 DNS1=10.10.15.161 DNS2=10.10.18.36 GATEWAY=10.10.191.254 HWADDR=00:1D:09:FE:DA:04 IPADDR=10.10.191.210 NETMASK=255.255.255.0 NETWORK=10.39.191.0 ONPARENT=yes How would the resolv.conf file should change since there are two different gateways? Any other change needed?

  Read the article

• Have I pushed the limits of my current VPS or is there room for optimization?

  - by JRameau

  I am currently on a mediatemple DV server (basic) 512mb dedicated ram, this is a CentOS based VPS with Plesk and Virtuozzo. My experience with it from day 1 has been bad and I only could sooth my server issues with several caching "Band-aids," but my sites are not as small as they were a year ago either so the issues have worsen. I have 3 Drupal installs running on separate (plesk) domains, 1 of those drupal installs is a multisite, that consists of 5-6 sites 2 of those sites are bringing in actual traffic. Those caching "Band-aids" I mentioned are APC, which seemed to help alot initially, and Drupal's Boost, which is considered a poorman's Varnish, it makes all my pages static for anonymous users. Last 30day combined estimate on Google Ananlytics: 90k visitors 260k pageviews. Issue: alot of downtime, I am continually checking if my sites are up, and lately I have been finding it down more than 3 times daily. Restarting Apache will bring it back up, for some time. I have google search every error message and looked up ways to optimize my DV server, and I am beyond stump what is my next move. Is this server bad, have I hit a impossibly low restriction such as the 12mb kernel memory barrier (kmemsize), is it on my end, do I need to optimize some more? *I have provided as much information as I can below, any help or suggestions given will be appreciated Common Error messages I see in the log: [error] (12)Cannot allocate memory: fork: Unable to fork new process [error] make_obcallback: could not import mod_python.apache.\n Traceback (most recent call last): File "/usr/lib/python2.4/site-packages/mod_python/apache.py", line 21, in ? import traceback File "/usr/lib/python2.4/traceback.py", line 3, in ? import linecache ImportError: No module named linecache [error] python_handler: no interpreter callback found. [warn-phpd] mmap cache can't open /var/www/vhosts/***/httpdocs/*** - Too many open files in system (pid ***) [alert] Child 8125 returned a Fatal error... Apache is exiting! [emerg] (43)Identifier removed: couldn't grab the accept mutex [emerg] (22)Invalid argument: couldn't release the accept mutex cat /proc/user_beancounters: Version: 2.5 uid resource held maxheld barrier limit failcnt 41548: kmemsize 4582652 5306699 12288832 13517715 21105036 lockedpages 0 0 600 600 0 privvmpages 38151 42676 229036 249036 0 shmpages 16274 16274 17237 17237 2 dummy 0 0 0 0 0 numproc 43 46 300 300 0 physpages 27260 29528 0 2147483647 0 vmguarpages 0 0 131072 2147483647 0 oomguarpages 27270 29538 131072 2147483647 0 numtcpsock 21 29 300 300 0 numflock 8 8 480 528 0 numpty 1 1 30 30 0 numsiginfo 0 1 1024 1024 0 tcpsndbuf 648440 675272 2867477 4096277 1711499 tcprcvbuf 301620 359716 2867477 4096277 0 othersockbuf 4472 4472 1433738 2662538 0 dgramrcvbuf 0 0 1433738 1433738 0 numothersock 12 12 300 300 0 dcachesize 0 0 2684271 2764800 0 numfile 3447 3496 6300 6300 3872 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 14 14 200 200 0 TOP: (In January the load avg was really high 3-10, I was able to bring it down where it is currently is by giving APC more memory play around with) top - 16:46:07 up 2:13, 1 user, load average: 0.34, 0.20, 0.20 Tasks: 40 total, 2 running, 37 sleeping, 0 stopped, 1 zombie Cpu(s): 0.3% us, 0.1% sy, 0.0% ni, 99.7% id, 0.0% wa, 0.0% hi, 0.0% si Mem: 916144k total, 156668k used, 759476k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached MySQLTuner: (after optimizing every table and repairing any table with overage I got the fragmented count down to 86) [--] Data in MyISAM tables: 285M (Tables: 1105) [!!] Total fragmented tables: 86 [--] Up for: 2h 44m 38s (409K q [41.421 qps], 6K conn, TX: 1B, RX: 174M) [--] Reads / Writes: 79% / 21% [--] Total buffers: 58.0M global + 2.7M per thread (100 max threads) [!!] Query cache prunes per day: 675307 [!!] Temporary tables created on disk: 35% (7K on disk / 20K total)

  Read the article

• Aptana show .htaccess files

  - by pygorex1

  Using the new Aptana Studio 2.0 and loving it. Trying to open and edit .htaccess files in Aptana Studio, but it's not showing up in the PHP Explorer pane, which normally shows all files, but not .htaccess.

  Read the article

• When and why would Windows Explorer lock an external hard disk?

  - by Ngu Soon Hui

  I am quite surprised to see that Windows Explorer is locking my external hard disk. Is there any reason why explorer.exe is holding on to my external hard disk? Before I was trying to detach the external hard disk, I was opening a csproj file using Visual Studio 2008. I made sure that I closed down Visual Studio before trying to detach the external hard disk. There was no other active program except Google Chrome, from what I could see, that was running.

  Read the article

• What do these messages in the Qmail maillog indicate?

  - by Griffo

  There seems to be an endless supply of messages in the Qmail maillog for a single address. Can anyone shed some light on why this might be and whether it is a problem? To me it looks like either spam or some sort of unhandled problem. It strikes me as unusual that the 'from=' field is blank. This is on a VPS using Plesk in case that's important. Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23593]: [email protected] Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23586]: from= Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23586]: [email protected] Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23585]: from= Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23585]: [email protected] Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23584]: from= Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23584]: [email protected] Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23583]: from= Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23583]: [email protected] Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23600]: from= Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23600]: [email protected] Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23599]: from= Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23599]: [email protected] EDIT Here's a sample of one of the emails: Received: (qmail 5603 invoked for bounce); 29 Jun 2011 07:46:31 +0100 Date: 29 Jun 2011 07:46:31 +0100 From: [email protected] To: [email protected] Subject: failure notice Hi. This is the qmail-send program at vps-1001108-595.cp.blacknight.com. I'm afraid I wasn't able to deliver your message to the following addresses. This is a permanent error; I've given up. Sorry it didn't work out. <[email protected]>: 200.147.36.13 does not like recipient. Remote host said: 450 4.7.1 Client host rejected: cannot find your hostname, [78.153.208.195] Giving up on 200.147.36.13. I'm not going to try again; this message has been in the queue too long. --- Below this line is a copy of the message. Return-Path: <[email protected]> Received: (qmail 15585 invoked by uid 48); 22 Jun 2011 07:38:26 +0100 Date: 22 Jun 2011 07:38:26 +0100 Message-ID: <[email protected]> To: [email protected] Subject: Cadastre-se e Concorra ? um Carro! MIME-Version: 1.0 Content-type: text/html; charset=iso-8859-1 From: Cielo Fidelidade <[email protected]> <!DOCTYPE HTML> <html> ... <body text removed> <html> If I understand this correctly, this is saying that an email sent by my server, from address [email protected], could not be delivered. However, [email protected] is not a valid email address on my server, so how can email be sent from this address on my server? I have tested whether my server is acting as an open relay, and it isn't. So how else could this be happening? I am getting thousands of these every day. What can I do to prevent it?

  Read the article

• Ubuntu 10.04: OpenVZ Kernel and pure-ftpd issues on HOST (no guest setup yet)

  - by Seidr

  After compiling and installing the OpenVZ flavour of kernel under Ubuntu 10.04, I am unable to browse to certain directories when connecting to the pure-ftpd server. The clients are dropping into PASSIVE mode, which is fine. This behaviour was happening before the change of kernel, however now when I browse to certain directories the connection just gets dropped. This only happens with a few directories under one login (web in specific), where as with another login it happens as soon as I connect. I've got the nf_conntrack_ftp kernel module installed (required to keep track of passive FTP connections as I understand, and an alias of the ip_conntrack_ftp module), however this has provided no alleviation of my problem. This module was actually required upon initial setup of my OS to get passive FTP working correctly, however when I compiled the OpenVZ kernel a lot of these modules were missing (iptables, conntrack etc). I recompiled the kernel with the missing modules, but to no effect. I've turned verbosity for the pure-ftpd server up, and still no clues have been spotted in either syslog or the transfer log. Neither did an strace provide any clues (that I could discern anyway) - although one strange thing is both in the output to the client and in the strace I notice that it does infact probe the directory and return the number of matches - it just fails after that. One more thing to mention is that if I FTP using the same credentials locally, everything works fine. This suggests that it is in fact an issue with either the conntrack_ftp module not functioning as expected, or a deeper networking issue. The Kernel was compiled and installed following the instructions at https://help.ubuntu.com/community/OpenVZ - bar the changes to the Kernel configuration (such as add iptables as a module). Below is an example of the log sent to the data (under FileZilla). Status: Resolving address of xxxx.co.uk Status: Connecting to 78.46.xxx.xxx:21... Status: Connection established, waiting for welcome message... Response: 220---------- Welcome to Pure-FTPd [privsep] [TLS] ---------- Response: 220-You are user number 4 of 10 allowed. Response: 220-Local time is now 08:52. Server port: 21. Response: 220-This is a private system - No anonymous login Response: 220-IPv6 connections are also welcome on this server. Response: 220 You will be disconnected after 15 minutes of inactivity. Command: USER xxx Response: 331 User xxx OK. Password required Command: PASS ******** Response: 230-User xxx has group access to: client1 sshusers Response: 230 OK. Current restricted directory is / Command: OPTS UTF8 ON Response: 200 OK, UTF-8 enabled Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is your current location Status: Directory listing successful Status: Retrieving directory listing... Command: CWD /web Response: 250 OK. Current directory is /web Command: TYPE I Response: 200 TYPE is now 8-bit binary Command: PORT 10,0,2,30,14,143 Response: 500 I won't open a connection to 10.0.2.30 (only to 188.220.xxx.xxx) Command: PASV Response: 227 Entering Passive Mode (78,46,79,147,234,110) Command: MLSD Response: 150 Accepted data connection Response: 226-ASCII Response: 226-Options: -a -l Response: 226 57 matches total Error: Could not read from transfer socket: ECONNRESET - Connection reset by peer Error: Failed to retrieve directory listing Any suggestions please? I'm willing to try anything!

  Read the article

• Run one virtual machine on a Linux server + standard Linux functions

  - by fistameeny

  Hi, I am looking for a method to setup a Linux server (running Ubuntu Server) that uses Samba for file sharing, as well as hosting a Windows virtual machine (in this case, Windows Small Business Server 2003, which in turn hosts SQL Server Express - Exchange won't be used on this). I would like to have the Linux server serving the files over Samba, and hosting the Virtual Machine. This obviously rules ESXi out as it couldn't do Samba at the same time. What would be the next best solution to give reasonable speed? Vmware Server 2.0, VirtualBox, Xen? There will be 10-15 users accessing the Samba shares and the SQL Express virtual machine. Matt

  Read the article

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• why nginx rewrite post request from /login to //login?

  - by jiangchengwu

  There is a if statement, which will rewrite url when the client is Android. Everything ok. But, something got strange. Nginx will write post request /login to //login, even if the block of if statement is bank. So I got a 404 page. As the jetty server only accept /login request. Server conf: location / { proxy_pass http://localhost:8785/; proxy_set_header Host $http_host; proxy_set_header Remote-Addr $http_remote_addr; proxy_set_header X-Real-IP $remote_addr; if ( $http_user_agent ~ Android ){ # rewrite something, been commented } } Debug info, origin log https://gist.github.com/3799021 ... 2012/09/28 16:29:49 [debug] 26416#0: *1 http script regex: "Android" 2012/09/28 16:29:49 [notice] 26416#0: *1 "Android" matches "Android/1.0", client: 106.187.97.22, server: ireedr.com, request: "POST /login HTTP/1.1", host: "ireedr.com" ... 2012/09/28 16:29:49 [debug] 26416#0: *1 http proxy header: "POST //login HTTP/1.0 Host: ireedr.com X-Real-IP: 106.187.97.22 Connection: close Accept-Encoding: identity, deflate, compress, gzip Accept: */* User-Agent: Android/1.0 " ... 2012/09/28 16:29:49 [debug] 26416#0: *1 HTTP/1.1 404 Not Found Server: nginx/1.2.1 Date: Fri, 28 Sep 2012 08:29:49 GMT Content-Type: text/html;charset=ISO-8859-1 Transfer-Encoding: chunked Connection: keep-alive Cache-Control: must-revalidate,no-cache,no-store Content-Encoding: gzip ... Only when I commented the block in the configration file: location / { proxy_pass http://localhost:8785/; proxy_set_header Host $http_host; proxy_set_header Remote-Addr $http_remote_addr; proxy_set_header X-Real-IP $remote_addr; #if ( $http_user_agent ~ Android ){ # #} } The client can get an 200 response. Debug info, origin log https://gist.github.com/3799023 ... "POST /login HTTP/1.0 Host: ireedr.com X-Real-IP: 106.187.97.22 Connection: close Accept-Encoding: identity, deflate, compress, gzip Accept: */* User-Agent: Android/1.0 " ... 2012/09/28 16:27:19 [debug] 26319#0: *1 HTTP/1.1 200 OK Server: nginx/1.2.1 Date: Fri, 28 Sep 2012 08:27:19 GMT Content-Type: application/json;charset=UTF-8 Content-Length: 17 Connection: keep-alive ... As the log: 2012/09/28 16:29:49 [notice] 26416#0: *1 "Android" matches "Android/1.0", client: 106.187.97.22, server: ireedr.com, request: "POST /login HTTP/1.1", host: "ireedr.com" 2012/09/28 16:29:49 [debug] 26416#0: *1 http script if 2012/09/28 16:29:49 [debug] 26416#0: *1 post rewrite phase: 4 2012/09/28 16:29:49 [debug] 26416#0: *1 generic phase: 5 2012/09/28 16:29:49 [debug] 26416#0: *1 generic phase: 6 2012/09/28 16:29:49 [debug] 26416#0: *1 generic phase: 7 2012/09/28 16:29:49 [debug] 26416#0: *1 access phase: 8 2012/09/28 16:29:49 [debug] 26416#0: *1 access phase: 9 2012/09/28 16:29:49 [debug] 26416#0: *1 access phase: 10 2012/09/28 16:29:49 [debug] 26416#0: *1 post access phase: 11 2012/09/28 16:29:49 [debug] 26416#0: *1 try files phase: 12 2012/09/28 16:29:49 [debug] 26416#0: *1 posix_memalign: 0000000001E798F0:4096 @16 2012/09/28 16:29:49 [debug] 26416#0: *1 http init upstream, client timer: 0 2012/09/28 16:29:49 [debug] 26416#0: *1 epoll add event: fd:13 op:3 ev:80000005 2012/09/28 16:29:49 [debug] 26416#0: *1 http script copy: "Host: " 2012/09/28 16:29:49 [debug] 26416#0: *1 http script var: "ireedr.com" 2012/09/28 16:29:49 [debug] 26416#0: *1 http script copy: " " 2012/09/28 16:29:49 [debug] 26416#0: *1 http script copy: "" 2012/09/28 16:29:49 [debug] 26416#0: *1 http script copy: "" 2012/09/28 16:29:49 [debug] 26416#0: *1 http script copy: "X-Real-IP: " 2012/09/28 16:29:49 [debug] 26416#0: *1 http script var: "106.187.97.22" 2012/09/28 16:29:49 [debug] 26416#0: *1 http script copy: " " 2012/09/28 16:29:49 [debug] 26416#0: *1 http script copy: "Connection: close " 2012/09/28 16:29:49 [debug] 26416#0: *1 http proxy header: "Accept-Encoding: identity, deflate, compress, gzip" 2012/09/28 16:29:49 [debug] 26416#0: *1 http proxy header: "Accept: */*" 2012/09/28 16:29:49 [debug] 26416#0: *1 http proxy header: "User-Agent: Android/1.0" 2012/09/28 16:29:49 [debug] 26416#0: *1 http proxy header: "POST //login HTTP/1.0 Host: ireedr.com X-Real-IP: 106.187.97.22 Connection: close Accept-Encoding: identity, deflate, compress, gzip Accept: */* User-Agent: Android/1.0 " ... Maybe post rewrite phase had rewrite the request. Anybody can help me to solve this problem or know why nginx do that ? Much appreciated.

  Read the article

• Incorrect gzipping of http requests, can't find who's doing it

  - by Ned Batchelder

  We're seeing some very strange mangling of HTTP responses, and we can't figure out what is doing it. We have an app server handling JSON requests. Occasionally, the response is returned gzipped, but with incorrect headers that prevent the browser from interpreting it correctly. The problem is intermittent, and changes behavior over time. Yesterday morning it seemed to fail 50% of the time, and in fact, seemed tied to one of our two load-balanced servers. Later in the afternoon, it was failing only 20 times out of 1000, and didn't correlate with an app server. The two app servers are running Apache 2.2 with mod_wsgi and a Django app stack. They have identical Apache configs and source trees, and even identical packages installed on Red Hat. There's a hardware load balancer in front, I don't know the make or model. Akamai is also part of the food chain, though we removed Akamai and still had the problem. Here's a good request and response: * Connected to example.com (97.7.79.129) port 80 (#0) > POST /claim/ HTTP/1.1 > User-Agent: curl/7.19.7 (x86_64-pc-linux-gnu) libcurl/7.19.7 OpenSSL/0.9.8k zlib/1.2.3.3 libidn/1.15 > Host: example.com > Accept: */* > Referer: http://example.com/apps/ > Accept-Encoding: gzip,deflate > Content-Length: 29 > Content-Type: application/x-www-form-urlencoded > } [data not shown] < HTTP/1.1 200 OK < Server: Apache/2 < Content-Language: en-us < Content-Encoding: identity < Content-Length: 47 < Content-Type: application/x-javascript < Connection: keep-alive < Vary: Accept-Encoding < { [data not shown] * Connection #0 to host example.com left intact * Closing connection #0 {"msg": "", "status": "OK", "printer_name": ""} And here's a bad one: * Connected to example.com (97.7.79.129) port 80 (#0) > POST /claim/ HTTP/1.1 > User-Agent: curl/7.19.7 (x86_64-pc-linux-gnu) libcurl/7.19.7 OpenSSL/0.9.8k zlib/1.2.3.3 libidn/1.15 > Host: example.com > Accept: */* > Referer: http://example.com/apps/ > Accept-Encoding: gzip,deflate > Content-Length: 29 > Content-Type: application/x-www-form-urlencoded > } [data not shown] < HTTP/1.1 200 OK < Server: Apache/2 < Content-Language: en-us < Content-Encoding: identity < Content-Type: application/x-javascript < Content-Encoding: gzip < Content-Length: 59 < Connection: keep-alive < Vary: Accept-Encoding < X-N: S < { [data not shown] * Connection #0 to host example.com left intact * Closing connection #0 ?V?-NW?RPR?QP*.I,)-???A??????????T??Z? ??/ There are two things to notice about the bad response: It has two Content-Encoding headers, and the browsers seem to use the first. So they see an identity encoding header, and gzipped content, so they can't interpret the response. The bad response has an extra "X-N: S" header. Perhaps if I could find out what intermediary adds "X-N: S" headers to responses, I could track down the culprit...

  Read the article

• Trouble with site-to-site OpenVPN & pfSense not passing traffic

  - by JohnCC

  I'm trying to get an OpenVPN tunnel going on pfSense 1.2.3-RELEASE running on embedded routers. I have a local LAN 10.34.43.0/254. The remote LAN is 10.200.1.0/24. The local pfSense is configured as the client, and the remote is configured as the server. My OpenVPN tunnel is using the IP range 10.99.89.0/24 internally. There are also some additional LANs on the remote side routed through the tunnel, but the issue is not with those since my connectivity fails before that point in the chain. The tunnel comes up fine and the logs look healthy. What I find is this:- I can ping and telnet to the remote LAN and the additional remote LANs from the local pfSense box's shell. I cannot ping or telnet to any remote LANs from the local network. I cannot ping or telnet to the local network from the remote LAN or the remote pfSense box's shell. If I tcpdump the tun interfaces on both sides and ping from the local LAN, I see the packets hit the tunnel locally, but they do not appear on the remote side (nor do they appear on the remote LAN interface if I tcpdump that). If I tcpdump the tun interfaces on both sides and ping from the local pfSense shell, I see the packets hit the tunnel locally, and exit the remote side. I can also tcpdump the remote LAN interface and see them pass there too. If I tcpdump the tun interfaces on both sides and ping from the remote pfSense shell, I see the packets hit the remote tun but they do not emerge from the local one. Here is the config file the remote side is using:- #user nobody #group nobody daemon keepalive 10 60 ping-timer-rem persist-tun persist-key dev tun proto udp cipher BF-CBC up /etc/rc.filter_configure down /etc/rc.filter_configure server 10.99.89.0 255.255.255.0 client-config-dir /var/etc/openvpn_csc push "route 10.200.1.0 255.255.255.0" lport <port> route 10.34.43.0 255.255.255.0 ca /var/etc/openvpn_server0.ca cert /var/etc/openvpn_server0.cert key /var/etc/openvpn_server0.key dh /var/etc/openvpn_server0.dh comp-lzo push "route 205.217.5.128 255.255.255.224" push "route 205.217.5.64 255.255.255.224" push "route 165.193.147.128 255.255.255.224" push "route 165.193.147.32 255.255.255.240" push "route 192.168.1.16 255.255.255.240" push "route 192.168.2.16 255.255.255.240" Here is the local config:- writepid /var/run/openvpn_client0.pid #user nobody #group nobody daemon keepalive 10 60 ping-timer-rem persist-tun persist-key dev tun proto udp cipher BF-CBC up /etc/rc.filter_configure down /etc/rc.filter_configure remote <host> <port> client lport 1194 ifconfig 10.99.89.2 10.99.89.1 ca /var/etc/openvpn_client0.ca cert /var/etc/openvpn_client0.cert key /var/etc/openvpn_client0.key comp-lzo You can see the relevant parts of the routing tables extracted from pfSense here http://pastie.org/5365800 The local firewall permits all ICMP from the LAN, and my PC is allowed everything to anywhere. The remote firewall treats its LAN as trusted and permits all traffic on that interface. Can anyone suggest why this is not working, and what I could try next?

  Read the article

• Severe mysqldump performance degradation using Centos Linux, 8GB PAE and MySQL 5.0.77

  - by Duncan Harris

  We use MySQL 5.0.77 on CentOS 5.5 on VMWare: Linux dev.ic.soschildrensvillages.org.uk 2.6.18-194.11.4.el5PAE #1 SMP Tue Sep 21 05:48:23 EDT 2010 i686 i686 i386 GNU/Linux We have recently upgraded from 4GB RAM to 8GB. When we did this the time of our mysqldump overnight backup jumped from under 10 minutes to over 2 hours. It also caused unresponsiveness on our plone based web site due to database load. The dump is using the optimized mysqldump format and is spooled directly through a socket to another server. Any ideas on what we could do to fix gratefully appreciated. Would a MySQL upgrade help? Anything we can do to MySQL config? Anything we can do to Linux config? Or do we have to add another server or go to 64-bit? We ran a previous (non-virtual) server on 6GB PAE and didn't notice a similar issue. This was on same MySQL version, but Centos 4.4. Server config file: [mysqld] port=3307 socket=/tmp/mysql_live.sock wait_timeout=31536000 interactive_timeout=31536000 datadir=/var/mysql/live/data user=mysql max_connections = 200 max_allowed_packet = 64M table_cache = 2048 binlog_cache_size = 128K max_heap_table_size = 32M sort_buffer_size = 2M join_buffer_size = 2M lower_case_table_names = 1 innodb_data_file_path = ibdata1:10M:autoextend innodb_buffer_pool_size=1G innodb_log_file_size=300M innodb_log_buffer_size=8M innodb_flush_log_at_trx_commit=1 innodb_file_per_table [mysqldump] # Do not buffer the whole result set in memory before writing it to # file. Required for dumping very large tables quick max_allowed_packet = 64M [mysqld_safe] # Increase the amount of open files allowed per process. Warning: Make # sure you have set the global system limit high enough! The high value # is required for a large number of opened tables open-files-limit = 8192 Server variables: mysql> show variables; +---------------------------------+------------------------------------------------------------------+ | Variable_name | Value | +---------------------------------+------------------------------------------------------------------+ | auto_increment_increment | 1 | | auto_increment_offset | 1 | | automatic_sp_privileges | ON | | back_log | 50 | | basedir | /usr/local/mysql-5.0.77-linux-i686-glibc23/ | | binlog_cache_size | 131072 | | bulk_insert_buffer_size | 8388608 | | character_set_client | latin1 | | character_set_connection | latin1 | | character_set_database | latin1 | | character_set_filesystem | binary | | character_set_results | latin1 | | character_set_server | latin1 | | character_set_system | utf8 | | character_sets_dir | /usr/local/mysql-5.0.77-linux-i686-glibc23/share/mysql/charsets/ | | collation_connection | latin1_swedish_ci | | collation_database | latin1_swedish_ci | | collation_server | latin1_swedish_ci | | completion_type | 0 | | concurrent_insert | 1 | | connect_timeout | 10 | | datadir | /var/mysql/live/data/ | | date_format | %Y-%m-%d | | datetime_format | %Y-%m-%d %H:%i:%s | | default_week_format | 0 | | delay_key_write | ON | | delayed_insert_limit | 100 | | delayed_insert_timeout | 300 | | delayed_queue_size | 1000 | | div_precision_increment | 4 | | keep_files_on_create | OFF | | engine_condition_pushdown | OFF | | expire_logs_days | 0 | | flush | OFF | | flush_time | 0 | | ft_boolean_syntax | + -><()~*:""&| | | ft_max_word_len | 84 | | ft_min_word_len | 4 | | ft_query_expansion_limit | 20 | | ft_stopword_file | (built-in) | | group_concat_max_len | 1024 | | have_archive | YES | | have_bdb | NO | | have_blackhole_engine | YES | | have_compress | YES | | have_crypt | YES | | have_csv | YES | | have_dynamic_loading | YES | | have_example_engine | NO | | have_federated_engine | YES | | have_geometry | YES | | have_innodb | YES | | have_isam | NO | | have_merge_engine | YES | | have_ndbcluster | DISABLED | | have_openssl | DISABLED | | have_ssl | DISABLED | | have_query_cache | YES | | have_raid | NO | | have_rtree_keys | YES | | have_symlink | YES | | hostname | app.ic.soschildrensvillages.org.uk | | init_connect | | | init_file | | | init_slave | | | innodb_additional_mem_pool_size | 1048576 | | innodb_autoextend_increment | 8 | | innodb_buffer_pool_awe_mem_mb | 0 | | innodb_buffer_pool_size | 1073741824 | | innodb_checksums | ON | | innodb_commit_concurrency | 0 | | innodb_concurrency_tickets | 500 | | innodb_data_file_path | ibdata1:10M:autoextend | | innodb_data_home_dir | | | innodb_adaptive_hash_index | ON | | innodb_doublewrite | ON | | innodb_fast_shutdown | 1 | | innodb_file_io_threads | 4 | | innodb_file_per_table | ON | | innodb_flush_log_at_trx_commit | 1 | | innodb_flush_method | | | innodb_force_recovery | 0 | | innodb_lock_wait_timeout | 50 | | innodb_locks_unsafe_for_binlog | OFF | | innodb_log_arch_dir | | | innodb_log_archive | OFF | | innodb_log_buffer_size | 8388608 | | innodb_log_file_size | 314572800 | | innodb_log_files_in_group | 2 | | innodb_log_group_home_dir | ./ | | innodb_max_dirty_pages_pct | 90 | | innodb_max_purge_lag | 0 | | innodb_mirrored_log_groups | 1 | | innodb_open_files | 300 | | innodb_rollback_on_timeout | OFF | | innodb_support_xa | ON | | innodb_sync_spin_loops | 20 | | innodb_table_locks | ON | | innodb_thread_concurrency | 8 | | innodb_thread_sleep_delay | 10000 | | interactive_timeout | 31536000 | | join_buffer_size | 2097152 | | key_buffer_size | 8384512 | | key_cache_age_threshold | 300 | | key_cache_block_size | 1024 | | key_cache_division_limit | 100 | | language | /usr/local/mysql-5.0.77-linux-i686-glibc23/share/mysql/english/ | | large_files_support | ON | | large_page_size | 0 | | large_pages | OFF | | lc_time_names | en_US | | license | GPL | | local_infile | ON | | locked_in_memory | OFF | | log | OFF | | log_bin | OFF | | log_bin_trust_function_creators | OFF | | log_error | | | log_queries_not_using_indexes | OFF | | log_slave_updates | OFF | | log_slow_queries | OFF | | log_warnings | 1 | | long_query_time | 10 | | low_priority_updates | OFF | | lower_case_file_system | OFF | | lower_case_table_names | 1 | | max_allowed_packet | 67108864 | | max_binlog_cache_size | 4294963200 | | max_binlog_size | 1073741824 | | max_connect_errors | 10 | | max_connections | 200 | | max_delayed_threads | 20 | | max_error_count | 64 | | max_heap_table_size | 33554432 | | max_insert_delayed_threads | 20 | | max_join_size | 18446744073709551615 | | max_length_for_sort_data | 1024 | | max_prepared_stmt_count | 16382 | | max_relay_log_size | 0 | | max_seeks_for_key | 4294967295 | | max_sort_length | 1024 | | max_sp_recursion_depth | 0 | | max_tmp_tables | 32 | | max_user_connections | 0 | | max_write_lock_count | 4294967295 | | multi_range_count | 256 | | myisam_data_pointer_size | 6 | | myisam_max_sort_file_size | 2146435072 | | myisam_recover_options | OFF | | myisam_repair_threads | 1 | | myisam_sort_buffer_size | 8388608 | | myisam_stats_method | nulls_unequal | | ndb_autoincrement_prefetch_sz | 1 | | ndb_force_send | ON | | ndb_use_exact_count | ON | | ndb_use_transactions | ON | | ndb_cache_check_time | 0 | | ndb_connectstring | | | net_buffer_length | 16384 | | net_read_timeout | 30 | | net_retry_count | 10 | | net_write_timeout | 60 | | new | OFF | | old_passwords | OFF | | open_files_limit | 8192 | | optimizer_prune_level | 1 | | optimizer_search_depth | 62 | | pid_file | /var/mysql/live/mysqld.pid | | plugin_dir | | | port | 3307 | | preload_buffer_size | 32768 | | profiling | OFF | | profiling_history_size | 15 | | protocol_version | 10 | | query_alloc_block_size | 8192 | | query_cache_limit | 1048576 | | query_cache_min_res_unit | 4096 | | query_cache_size | 0 | | query_cache_type | ON | | query_cache_wlock_invalidate | OFF | | query_prealloc_size | 8192 | | range_alloc_block_size | 4096 | | read_buffer_size | 131072 | | read_only | OFF | | read_rnd_buffer_size | 262144 | | relay_log | | | relay_log_index | | | relay_log_info_file | relay-log.info | | relay_log_purge | ON | | relay_log_space_limit | 0 | | rpl_recovery_rank | 0 | | secure_auth | OFF | | secure_file_priv | | | server_id | 0 | | skip_external_locking | ON | | skip_networking | OFF | | skip_show_database | OFF | | slave_compressed_protocol | OFF | | slave_load_tmpdir | /tmp/ | | slave_net_timeout | 3600 | | slave_skip_errors | OFF | | slave_transaction_retries | 10 | | slow_launch_time | 2 | | socket | /tmp/mysql_live.sock | | sort_buffer_size | 2097152 | | sql_big_selects | ON | | sql_mode | | | sql_notes | ON | | sql_warnings | OFF | | ssl_ca | | | ssl_capath | | | ssl_cert | | | ssl_cipher | | | ssl_key | | | storage_engine | MyISAM | | sync_binlog | 0 | | sync_frm | ON | | system_time_zone | GMT | | table_cache | 2048 | | table_lock_wait_timeout | 50 | | table_type | MyISAM | | thread_cache_size | 0 | | thread_stack | 196608 | | time_format | %H:%i:%s | | time_zone | SYSTEM | | timed_mutexes | OFF | | tmp_table_size | 33554432 | | tmpdir | /tmp/ | | transaction_alloc_block_size | 8192 | | transaction_prealloc_size | 4096 | | tx_isolation | REPEATABLE-READ | | updatable_views_with_limit | YES | | version | 5.0.77 | | version_comment | MySQL Community Server (GPL) | | version_compile_machine | i686 | | version_compile_os | pc-linux-gnu | | wait_timeout | 31536000 | +---------------------------------+------------------------------------------------------------------+ 237 rows in set (0.00 sec)

  Read the article

• Apache access.log interpretation

  - by Pantelis Sopasakis

  In the log file of apache (access.log) I find log entries like the following: 10.20.30.40 - - [18/Mar/2011:02:12:44 +0200] "GET /index.php HTTP/1.1" 404 505 "-" "Opera/9.80 (Windows NT 6.1; U; en) Presto/2.7.62 Version/11.01" Whose meaning is clear: The client with IP 10.20.30.40 applied a GET HTTP method on /index.php (that is to say http://mysite.org/index.php) receiving a status code 404 using Opera as client/browser. What I don't understand is entries like the following: 174.34.231.19 - - [18/Mar/2011:02:24:56 +0200] "GET http://www.siasatema.com HTTP/1.1" 200 469 "-" "Python-urllib/2.4" So here what I see is that someone (client with IP 174.34.231.19) accessed http://www.siasatema.com and got a 200 HTTP status code(?). It doesn't make sense to me... the only interpretation I can think of is that my apache server acts like proxy! Here are some other requests that don't have my site as destination... 187.35.50.61 - - [18/Mar/2011:01:28:20 +0200] "POST http://72.26.198.222:80/log/normal/ HTTP/1.0" 404 491 "-" "Octoshape-sua/1010120" 87.117.203.177 - - [18/Mar/2011:01:29:59 +0200] "CONNECT 64.12.244.203:80 HTTP/1.0" 405 556 "-" "-" 87.117.203.177 - - [18/Mar/2011:01:29:59 +0200] "open 64.12.244.203 80" 400 506 "-" "-" 87.117.203.177 - - [18/Mar/2011:01:30:04 +0200] "telnet 64.12.244.203 80" 400 506 "-" "-" 87.117.203.177 - - [18/Mar/2011:01:30:09 +0200] "64.12.244.203 80" 400 301 "-" "-" I believe that all these are related to some kind of attack or abuse of the server. Could someone explain to may what is going on and how to cope with this situation? Update 1: I disabled mod_proxy to make sure that I don't have an open proxy: # a2dismod proxy Where from I got the message: Module proxy already disabled I made sure that there is no file proxy.conf under $APACHE/mods-enabled. Finally, I set on my browser (Mozzila) my IP as a proxy and tried to access http://google.com. I was not redirected to google.com but instead my web page appeared. The same happened with trying to access http://a.b (!). So my server does not really work as a proxy since it does not forward the requests... But I think it would be better if somehow I could configure it to return a status code 403. Here is my apache configuration file: <VirtualHost *:80> ServerName mysite.org ServerAdmin webmaster@localhost DocumentRoot /var/www/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> Update 2: Using a block, I restrict the use of other methods than GET and POST... <Limit POST PUT CONNECT HEAD OPTIONS DELETE PATCH PROPFIND PROPPATCH MKCOL COPY MOVE LOCK UNLOCK> Order deny,allow Deny from all </Limit> <LimitExcept GET> Order deny,allow Deny from all </LimitExcept> Now methods other that GET are forbidden (403). My only question now is whether there is some trick to boot those how try to use my server as a proxy out...

  Read the article

• Importing statements into Quickbooks

  - by Raj More

  How do I import the following statements into Quickbooks Pro? Bank of America American Express

  Read the article

• Difference between `curl -I` and `curl -X HEAD`

  - by chmeee

  I was wathcing the funny server type from http://www.reddit.com with curl -I http://www.reddit.com when I guessed that curl -X HEAD http://www.reddit.com would do the same. But, in fact, it doesn't. I'm curious about why. This is what I observe running the two commands: curl -I: works as expected, outputs the header and exists. curl -X HEAD: does not show anything and seems to wait for user input. But, sniffing with tshark I see the second command actually sends the same HTML query and receives the correct answer, but it does not show it and it doesn't close the connection. curl -I 0.000000 333.33.33.33 -> 213.248.111.106 TCP 59675 > http [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=47267342 TSER=0 WS=6 0.045392 213.248.111.106 -> 333.33.33.33 TCP http > 59675 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1460 TSV=2552532839 TSER=47267342 WS=1 0.045441 333.33.33.33 -> 213.248.111.106 TCP 59675 > http [ACK] Seq=1 Ack=1 Win=5888 Len=0 TSV=47267353 TSER=2552532839 0.045623 333.33.33.33 -> 213.248.111.106 HTTP HEAD / HTTP/1.1 0.091665 213.248.111.106 -> 333.33.33.33 TCP http > 59675 [ACK] Seq=1 Ack=155 Win=6432 Len=0 TSV=2552532886 TSER=47267353 0.861782 213.248.111.106 -> 333.33.33.33 HTTP HTTP/1.1 200 OK 0.861830 333.33.33.33 -> 213.248.111.106 TCP 59675 > http [ACK] Seq=155 Ack=321 Win=6912 Len=0 TSV=47267557 TSER=2552533656 0.862127 333.33.33.33 -> 213.248.111.106 TCP 59675 > http [FIN, ACK] Seq=155 Ack=321 Win=6912 Len=0 TSV=47267557 TSER=2552533656 0.910810 213.248.111.106 -> 333.33.33.33 TCP http > 59675 [FIN, ACK] Seq=321 Ack=156 Win=6432 Len=0 TSV=2552533705 TSER=47267557 0.910880 333.33.33.33 -> 213.248.111.106 TCP 59675 > http [ACK] Seq=156 Ack=322 Win=6912 Len=0 TSV=47267570 TSER=2552533705 curl -X HEAD 34.106389 333.33.33.33 -> 213.248.111.90 TCP 51690 > http [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=47275868 TSER=0 WS=6 34.149507 213.248.111.90 -> 333.33.33.33 TCP http > 51690 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1460 TSV=3920268348 TSER=47275868 WS=1 34.149560 333.33.33.33 -> 213.248.111.90 TCP 51690 > http [ACK] Seq=1 Ack=1 Win=5888 Len=0 TSV=47275879 TSER=3920268348 34.149646 333.33.33.33 -> 213.248.111.90 HTTP HEAD / HTTP/1.1 34.191484 213.248.111.90 -> 333.33.33.33 TCP http > 51690 [ACK] Seq=1 Ack=155 Win=6432 Len=0 TSV=3920268390 TSER=47275879 34.192657 213.248.111.90 -> 333.33.33.33 TCP [TCP Dup ACK 15#1] http > 51690 [ACK] Seq=1 Ack=155 Win=6432 Len=0 TSV=3920268390 TSER=47275879 34.823399 213.248.111.90 -> 333.33.33.33 HTTP HTTP/1.1 200 OK 34.823453 333.33.33.33 -> 213.248.111.90 TCP 51690 > http [ACK] Seq=155 Ack=321 Win=6912 Len=0 TSV=47276048 TSER=3920269022 Any idea about why this difference in behaviour?

  Read the article

• Can't connect to local SQL Server

  - by D.M.

  I'm banging my head against the wall here and can't get things figured out. Yesterday I uninstalled SQL Server 2008 Express and installed a full copy of SQL Server 2008 R2. Everything installed fine but I can't connect to the database to save my life. There is a similar question here that never got answered and I'm not sure if this may be specific to 2008 R2 and how I may have installed. Under my old configuration (SQL Express) I connected with "DM\SQLEXPRESS" just fine. So far I've tried: DM\MSSQLSERVER - .\MSSQLSERVER - \MSSQLSERVER - MSSQLSERVER - DM\Dave\MSSQLSERVER and I get the "cannot connect to server" error every time. I have the service installed as well as the SQL Server Browser that I have started. If anyone had any suggestions that would be great.

  Read the article

• Nginx alias or rewrite for Horde Groupware ActiveSync URL does not process the rpc.php file

  - by Benny Li

  I'm trying to setup a Horde groupware with Nginx. The webinterface works but I do not get the ActiveSync specific URL to work. The Horde Wiki explains how to use it with an Apache Webserver here. My problem is, that I setup a rewrite (tried an alias too) to serve the location /horde/Microsoft-Server-ActiveSync via the /horde/rpc.php script. But with my current configuration nginx does the rewrite and returns a 200 status code. But it looks like that the php file is not executed. If I go to /horde/rpc.php directly it opens up the login dialog. So this seems to work correct. Firstly I was googling about the problem but could not find a working solution. So now I would like to ask you. The configuration should allow to access the ActiveSync part via the URL /horde/Microsoft-Server-ActiveSync. The horde webinterface is already accessible via /horde. My configuration looks like this: default-ssl.conf server { listen 443 ssl; ssl on; ssl_certificate /opt/nginx/conf/certs/server.crt; ssl_certificate_key /opt/nginx/conf/certs/server.key; server_name example.com; index index.html index.php; root /var/www; include sites-available/horde.conf; } horde.conf location /horde { rewrite_log on; rewrite ^/horde/Microsoft-Server-ActiveSync(.*)$ /horde/rpc.php$1 last; try_files $uri $uri/ /rampage.php?$args; location ~ \.php$ { try_files $uri =404; include sites-available/horde.fcgi-php.conf; } } horde.fcgi-php.conf include fastcgi_params; fastcgi_split_path_info ^(.+\.php)(/.+)$; fastcgi_param PATH_INFO $fastcgi_path_info; fastcgi_param PATH_TRANSLATED $document_root$fastcgi_path_info; fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_params (default nginx) fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param HTTPS $https if_not_empty; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; # PHP only, required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; The nginx log level is set to debug. The output after the request is: 2014/06/13 10:33:15 [notice] 17332#0: *1 "^/horde/Microsoft-Server-ActiveSync(.*)$" matches "/horde/Microsoft-Server-ActiveSync", client: XX.XX.XX.XX, server: example.com, request: "GET /horde/Microsoft-Server-ActiveSync HTTP/1.1", host: "example.com" 2014/06/13 10:33:15 [notice] 17332#0: *1 rewritten data: "/horde/rpc.php", args: "", client: XX.XX.XX.XX, server: example.com, request: "GET /horde/Microsoft-Server-ActiveSync HTTP/1.1", host: "example.com" All this is happening on a RaspberryPi with Raspbian GNU/Linux 7 (which is mainly a Debian Wheezy). So I guess the rewrite works but the php file is not processed?! Does anyone know where the problem is and how to fix it?

  Read the article

• Intel video driver upgrade now makes my external monitor display red-only with HDMI cable.

  - by Eli

  I have an HP G60 notebook with a Mobile Intel 4 Series Express Chipset video display (Driver version is 8.15.10.2021). OS is Win7 Home Premium. I also have an LG widescreen display that I was connecting to the laptop using an HDMI cable. It was working great, until I applied an Intel 4 Series Express Chipset update from Windows Update. After the update, if I plug the laptop to the monitor using the HDMI cable, it appears I only get the Magenta channel, cause that is all I see. If I connect with the VGA cable, it works fine. So, is it possible it is just the HDMI cable (which IS cheap in this case - fire sale at Blockbuster), and not related to the video driver update at all?

  Read the article

• Windows 7 safe mode pretends it's Windows XP?

  - by Joachim Kerschbaumer

  Just a question in between. A friend of mine brought me a laptop that does not work anymore and wanted me to check whether I can do something. She told me it's Windows 7, and startup screen and login screen look like it. However, as she gets a bluescreen on startup it is only possible to boot in safe mode where the system pretends to be Windows XP SP3. The system also may have 1 GB of RAM but the system itself states that it has 954 MB of RAM which is a value I've never seen before. Is everything corrupt from operating system to hardware, or am I just a newbie that does not know that Windows 7 pretends to be Windows XP SP3 in safe mode? Or is this laptop just the victim of an illegal, crazy copy of Windows XP sold as Windows 7? Maybe some strange Chinese stuff? I also recognized that the startup screen of Outlook Express reads "Outllok Express" (no typo) I´m kind of confused, maybe someone could put light into this ;)

  Read the article

< Previous Page | 446 447 448 449 450 451 452 453 454 455 456 457  | Next Page >