Search Results

Search found 28170 results on 1127 pages for '16 bit animation'.

Page 462/1127 | < Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >

  • Windows 7 freezes on boot screen

    - by this is a dead end
    There was some update that required me to restart my computer, so I did. when it restarted, it stays at the Windows boot screen forever, the screen that says "Starting Windows" and has that Windows logo in the middle. I've tried the start up repair program that shows up when I click F8 when the computer starts. And tried system restore but, it says it has restored windows successfully but it still freezes on the boot screen when I reboot it. When I try starting it in safe mode, it gets to the blue Windows background, the one with the logon screen, then says "Failure configuring Windows updates. Reverting Changes. Do not turn off." Then after a while it reboot by itself. Just noticed, the logo animation on the boot screen is still animated. So it's not completely frozen.

    Read the article

  • Can I clone my hard drive to an external and boot from the clone?

    - by willbuntu
    First thing: I am not asking what software I'm supposed to use. I already know the answer: Ghost (proprietary), Clonezilla, and dd (if I'm careful). What I really want to know is if it is possible to (essentially) bit-for-bit clone my entire installation (OS, installed software, activation(s), etc.) to an external USB hard-drive, and then boot off of that (if I need to, I know how to edit BIOS settings and use Plop boot manager), and work with it day-to-day as if there was virtually no difference from using my internal HDD now. Again, I'm not asking how to install Windows to an external (because I know I'd need to do some special workaround), I'm asking if I can clone everything and boot off of it. In case you're wondering why I'm going to this trouble: I'm using a Lenovo Essentials laptop that has an unmodifiable partition table (due to recovery crap), and has all 4 of its partitions spoken for (3 primary, one extended, cannot change the extended). Anyway, my thought is that if I can clone everything and boot off of it when I need to, and just have a Linux distro on the internal HDD, then that could work.

    Read the article

  • Windows 7 & Virtual PC and Internet (gateway) problems on host PC

    - by Mufasa
    I upgraded to Windows 7 on a PC that is a few years old. The CPU was one revision away from having Hyper-V on it. So, I had to install Microsoft Virtual PC 2007 (v6.0.156.0) to run full XP instances instead of the seamless XP virtualization that is advertised so much. That's fine though; the 'older' version is useful since I use it to run different versions of the whole XP/IE stack for testing. (I'm a web developer.) ...And for the one 16-bit application we still use at the office for scheduling. * sigh * The virtual instances work fine, including networking. My issue is that after a reboot or coming out of sleep mode, my host Windows 7 won't connect to the Internet. It will connect to the local network fine. If I disable the "Virtual Machine Network Services" item (I'll call "VMNS" from here on) in the LAN Connection properties box, it starts working. But than the Virtual PC instances lose their network connectivity. If I re-enable VMNS again in the same instance, everything works (Internet on host and in the virtualized instances). But after the next reboot/sleep cycle this starts over. The route table gave me a clue though. When doing a cycle w/ VMNS enabled: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 On-link 10.0.3.51 20 0.0.0.0 0.0.0.0 10.0.10.10 10.0.3.51 276 ... After VMNS is disabled, the first route goes away. I assume that is for VMNS to intercept virtualized instance's network connections and forward them correctly? Just a guess though. More info: I checked my Firewall settings and Services (because I'm sort of a control nazi and turn off a lot) but couldn't find anything that made sense and if turned on changed anything. So it might be something there I'm missing, but I don't know what. My current hacked solution: So, I figured I'd mess with the routes myself to see if that helped, it did. If I run a route delete 0.0.0.0 on the universal (0.0.0.0) gateway routes, and add back in just the 2nd line with route add 0.0.0.0 mask 0.0.0.0 10.0.10.10--the one that points to my actual gateway (10.0.10.10)--then I don't have to mess with the disable/enable cycle of VMNS, and everything works. Running those two commands is faster then bringing up connection options and disabling and re-enabling VMNS, but I still don't want to have use that hack script every boot either. (Oh, and I also tried messing with hard-coding TCP/IP settings in my network adapter, including setting high metrics, etc., but that didn't help either.) Any suggestions on the right way to fix this?

    Read the article

  • How to detect/list rogue computers connected to a WIFI network without access to the Wifi Router interface? [migrated]

    - by JJarava
    This is what I believe to be an interesting challenge :) A relative (that leaves a bit too far to go there in person) is complaining that their WIFI/Internet network performance has gone down abysmally lately. She'd like to know if some of the neighbors are using her wifi network to access the internet but she's not too technically savvy. I know that the best way to prevent issues would be to change the Router password, but it's a bit of a PITA having to re-configure all wifi devices... and if the uninvited guest broke the password once, they can do it again... Her wifi router/internet connection is provided by the telco, and remotely managed so she can log-on to their telco account's page and remotely change the router's Wifi password, but doesn't have access to the router status page/config/etc unless she opts out of the telco's remote support and mainteinance service... So, how could she check if there are guests in the wifi with this restrictions and in the most "point and click way"? In this case I'd probably use nmap to look for other devices in the network, but I'm not sure if that's the easiest way to do it. I'm not a wifi expert, so I don't know if there are any wifi-scanning utils that can tell us who's talking to the router... Lastly, she's a Windows user as I guess that'll influence the choice of tools available Any suggestions more than welcome Regards!

    Read the article

  • named responding recursive on norecurse queries

    - by Keks
    I have a server on which named is running. It is intercepted with another named server which it is not aware of. Querying the first named server results in timeouts. The server tries to resolve the query recursively. During that the firewall redirects the DNS Request from the first named server to the second one (the query from the first one is addressed to a e.g. a root server and has its "Recursion desired" bit set to 0). Despite that the second named responds to this request with a entirely or at least 1 level more resolved response than the first named server expects. So it ends up with a timeout even though it got a correct name server or even the full IP for the queried domain. In the first case the first name server tries to follow the authority domain ignoring the coresponding glue record and ends up in a loop it aborts: queried: google.com -> got from named#2: ns1.google.com -> ignore glue record and query: ns1.google.com -> got authority from named#2: google.com In the second case it ignores the answer section with the correct IP and instead tries to follow the name servers from the authority section, which ends up in the same dead end as case 1. So how can it be that the second named responds with recursive results even though the bit was explicitly set to 0 in the request from the first named?

    Read the article

  • How to distribute multiple executions of an app across many machines

    - by Salec
    I've got a simulation app (64-bit windows) that runs without any user interaction. This app gathers information and pushes it to a remote MS SQL Server. What I'd like to do is execute this simulation as many times as I can on multiple machines after our nightly build has finished and it has passed the test suite. If possible I'd love to have the ability to configure it to stop after x total runs or if the entire batch has taken over y hours. I've tried using Visual Studio's built in test framework since we already have a test lab set up with multiple agents. I created a single unit test that simply runs the simulation then I created an ordered test and added that single test multiple times (from what I gather, this is the only way to execute the same unit test more than once). I found that ordered tests are only run on a single agent and not distributed which is very limiting. We use TeamCity to perform our nightly builds and I suspect it's possible to implement this on top of that, but I'm fairly new to TeamCity. We also have Jenkins and Bamboo available and I'm open to any other software that would get the job done presuming it runs on a 64-bit Windows OS. Any suggestions?

    Read the article

  • VLC Crash when playing MKV files in Windows 7

    - by Phelios
    I'm not sure if the mkv file is corrupted, but when it is opened with VLC player, VLC loads up and displays nothing. Can't even close VLC after that. And also, VLC is running with 50% of the CPU. I have to use End Process to kill it. How do I know if the file is corrupted? How do I solve this? info from mediainfo Format : Matroska File size : 69.4 MiB Duration : 21mn 48s Overall bit rate : 445 Kbps Encoded date : UTC 2009-11-20 18:33:49 Writing application : mkvmerge v2.9.7 ('Tenderness') built on Jul 1 2009 18:43:35 Writing library : libebml v0.7.7 + libmatroska v0.8.1 Video ID : 1 Format : AVC Format/Info : Advanced Video Codec Format profile : [email protected] Format settings, CABAC : Yes Format settings, ReFrames : 2 frames Format settings, GOP : N=1 Codec ID : V_MPEG4/ISO/AVC Duration : 21mn 48s Width : 640 pixels Height : 352 pixels Display aspect ratio : 16:9 Frame rate : 23.976 fps Color space : YUV Chroma subsampling : 4:2:0 Bit depth : 8 bits Scan type : Progressive Audio ID : 2 Format : AAC Format/Info : Advanced Audio Codec Format profile : HE-AAC / LC Codec ID : A_AAC Duration : 21mn 48s Channel(s) : 2 channels Channel positions : Front: L R Sampling rate : 48.0 KHz / 24.0 KHz Compression mode : Lossy

    Read the article

  • USB-to-Serial showing gibberish at 115200 Baud

    - by Mose
    I've got a serious problem which drives me crazy because I tried everything I could think of. First of all, I made a video: http://youtu.be/boghkuq7L_s but please read the following text for more information, not only view the video! When using a USB-to-Serial interface everything works as long as I don't go beyond 57600 Baud. At higher rates I only get giberish like this: év.­b0JNLYÆÿ¿iëd0U²(kßÞb! ú]/xscB!ï¯!BoXûÿ1ïâÖCÿ6ÌAnè*íÌC)º¿BíÞØ.C.@ÆÃwHJÂs "YE:ñ.èFðÌCÊ÷ÞÄ !x H w6@BtbHJ ̪ Ì6ì H¾a¿bH.">îvy®;f<ßBÌ p­L¨fæH­E ­þ¼MBÞI What makes the problem so strange is, I exchanged every component and the problem still presists. I tried differtent OSes (Ubuntu, WinXP, Win7, OSX 10.7) with 32 and 64 Bit. I tried USB-to-Serial interface from FTDI and Prolific. I tried reading the output from my Raspberry PI and from an Asterisk Appliance. I changed the cables and the wiring. Nothing helped. In the video I made a example with a old Notebook with native COM and put the USB-to-Serial to the same connection as "sniffer" (only Rx and GND connected) to make sure the output and everything is ok as one can see on the native port. The voltage is ok. Settings for both are 115200 Baud, 8 Bit with 1 Stop and no flow control. Native is ok. USB is messed up. I used the newest drivers and double checked all connections. I have no idea what is wrong here. As I couldn't find anyone describing problems like this I question my long experiance in computer science and think I'm doing some completly wrong... Please help :-/

    Read the article

  • Apache's htcacheclean doesn't scale: How to tame a huge Apache disk_cache?

    - by flight
    We have an Apache setup with a huge disk_cache (500.000 entries, 50 GB disk space used). The cache grows by 16 GB every day. My problem is that the cache seems to be growing nearly as fast as it's possible to remove files and directories from the cache filesystem! The cache partition is an ext3 filesystem (100GB, "-t news") on an iSCSI storage. The Apache server (which acts as a caching proxy) is a VM. The disk_cache is configured with CacheDirLevels=2 and CacheDirLength=1, and includes variants. A typical file path is "/htcache/B/x/i_iGfmmHhxJRheg8NHcQ.header.vary/A/W/oGX3MAV3q0bWl30YmA_A.header". When I try to call htcacheclean to tame the cache (non-daemon mode, "htcacheclean-t -p/htcache -l15G"), IOwait is going through the roof for several hours. Without any visible action. Only after hours, htcacheclean starts to delete files from the cache partition, which takes a couple more hours. (A similar problem was brought up in the Apache mailing list in 2009, without a solution: http://www.mail-archive.com/[email protected]/msg42683.html) The high IOwait leads to problems with the stability of the web server (the bridge to the Tomcat backend server sometimes stalls). I came up with my own prune script, which removes files and directories from random subdirectories of the cache. Only to find that the deletion rate of the script is just slightly higher than the cache growth rate. The script takes ~10 seconds to read the a subdirectory (e.g. /htcache/B/x) and frees some 5 MB of disk space. In this 10 seconds, the cache has grown by another 2 MB. As with htcacheclean, IOwait goes up to 25% when running the prune script continuously. Any idea? Is this a problem specific to the (rather slow) iSCSI storage? Should I choose a different file system for a huge disk_cache? ext2? ext4? Are there any kernel parameter optimizations for this kind of scenario? (I already tried the deadline scheduler and a smaller read_ahead_kb, without effect).

    Read the article

  • empty file from tomcat https redirect?

    - by amertune
    I am using tomcat 6.0.20, with jdk 1.6.0_18 on 64 bit linux (tomcat downloaded from tomcat.apache.org, not installed from repositories). I have iptables redirects from port 80 - 8080 and 443 - 8443. In server.xml, the connector for port 8080 redirects to 443, and the 8443 connector has proxyPort="443". In conf/web.xml, I have added this bit at the end of the file (but still inside the <web-app</webapp tags). <security-constraint> <web-resource-collection> <web-resource-name>Protected Context</web-resource-name> <url-pattern>/*</url-pattern> </web-resource-collection> <user-data-constraint> <transport-guarantee>CONFIDENTIAL</transport-guarantee> </user-data-constraint> </security-constraint> I also have two contexts, ROOT and mywebapp. If I go to http://myurl.com, then I get redirected to https://myurl.com. If I go to http://myurl.com/mywebapp/, then I get redirected to https://myurl.com/mywebapp/. The problem I'm having is when I go to http://myurl.com/mywebapp (no trailing slash). When I do this I get a prompt to download an empty file that has an empty name. Going to https://myurl.com/mywebapp works. I would think that a user typing myurl.com/mywebapp is far from rare. Is there something I'm missing?

    Read the article

  • Will a SQL Server client alias survive a sysprep?

    - by shufler
    I want to sysprep a Windows Server 2008 R2 SP1 machine that has SQL Server 2008 R2 SP1 installed (for reference, SQL Server 2008 R2 has a new sysprep feature that allows the instance to be sysprepped). On the server is a SQL Server client alias that points to the default SQL Server database engine instance. For reference, the alias is called Alias-SQLServer and has been configured in both 32-bit and 64-bit cliconfig versions (that is, both registry keys exist) The alias points to the local instance as the image will be used to create development VMs and the installation script for the application that is being developed will use the SQL Server client alias in order to generalize the installation scripts. I can't seem to find information about whether the sysprep tool will update the SQL Server client alias's registry keys with the server's new name once it's unsealed. My guess is that it is not; how is sysprep to know that the server name the alias points to will be different for each image? Right? Perhaps if the alias points to localhost instead of the server name this will work?

    Read the article

  • How to disable monitor auto detection in Windows 7?

    - by Jay Yother
    I am currently running Windows 7 Ultimate 64-bit with a dual monitor setup with an NVIDIA 7950 GT graphics card. One monitor is dedicated to this machine and the other monitor is connected to a DVI KVM switch. When I switch to my other computer, Windows 7 disables the monitor. However, when I switch back it does not re-enable the monitor. The only circumstance that automatically re-enables the second monitor is when I switch back after Windows has put the monitors into power save mode. I am continually having to bring up the NVIDIA control panel to have it re-enable the monitor. Under Windows XP I would just disable the NVIDIA service to prevent it from auto-detecting the monitor (which doesn't solve the problem under Win7), and in Vista there was a registry hack that would prevent this. It looks as though that has been removed in Windows 7. I have found similar questions posted on this site, but nothing that matches my problem exactly. The following link is the question that comes the closest, but does not provide a solution to the problem. http://superuser.com/questions/96683/how-to-fix-monitor-detection-on-windows-7 Is there a way in Windows 7 to disable monitor auto-detection? Update: I just added a second graphics card to my Windows 7 64-bit machine. I plugged one monitor into each graphics card. Now, when I use the KVM switch to switch back and forth it will re-enable the second monitor like it should. There are however, a few quirks with this. If I have a program maximized on the second monitor and it has focus, when I switch it will move to monitor 1. If I have a program maximized on the second monitor and it does not have focus, when I switch it will behave like it is minimized and when I bring it back up it will show up maximized on monitor 1. Definitely better than it was, but still looking for a way to disable the auto-detection.

    Read the article

  • Migrating ODBC information through a batch file

    - by DeskSide
    I am a desktop support technician currently working on a large scale migration project across multiple sites. I am looking at a way to transfer ODBC entries from Windows XP to Windows 7. If anyone knows of a program or anything prebuilt that already does this, please redirect me. I've already looked but haven't found anything, so I'm trying to build my own. I know enough basic programming to read the work of others and monkey around with something that already exists, but not much else. I have come across a custom batch file written at one site that (among other things) exports ODBC information from the old computer and stores it on a server (labelled as y: through net use at the beginning of the file), then later transfers it from the server to a new computer. The pre-existing code is for Windows XP to XP migrations. Here are the pertinate bits of code: echo Exporting ODBC Information start /wait regedit.exe /e "y:\%username%\odbc.reg" HKEY_LOCAL_MACHINE\SOFTWARE\ODBC\ODBC.INI (and later on) echo Importing ODBC start /wait regedit /s "y:\%username%\odbc.reg" We are now migrating from Windows XP to 7, and this part of the batch file still seems to work for this particular site, where Oracle 8i and 10g are used. I'm looking to use my cut down version of this code at multiple sites, and I'm wondering if the same lines of code will still work for anything other than Oracle. Also, my research on this issue has shown that there are different locations in 64 bit operating systems for 32/64 bit entries, and I'm wondering what effect that would have on the code. Could I copy the same data to both parts of the registry, in hopes of catching everything? Any assistance would be appreciated. Thank you for your time.

    Read the article

  • VM load and ping problems after replacing server motherboard

    - by Andre
    Recently, we had to replace the motherboard of one of our servers. The procedure was done by IBM as it had guarantee. The server runs ESXi 5.1, with several virtual machines, including our main mail server (Domino) and a file server. After the replacing the motherboard and staring the VMs, ESXi asked us if we had moved it or copied (different motherboard is like a different computer). We clicked the latter. We started each machine and after some basic reconfiguration, all of them were up. However, we have been having problems with the mail server, it has been acting really slow at times (this could be when it syncs with the secondary mail server) and we have been checking with Centreon (a Nagios frontend) that its CPU load has been a bit high at times and ping response too. There was a moment this morning in which I tried connecting via SSH console and it was really slow to show login and basic commands like ifconfig and top. This particular mail server is a CentOS 4.4.7 64-bit. The little configuring we had to do after restarting it was to configure the network connection as it was resolving through DHCP. Our mail software is Lotus Notes server 9. Do you know of any way in which this replacement may be causing these difficulties, and how to fix it? Thanks.

    Read the article

  • Can not get sound over hdmi in kubuntu 9.10

    - by user32509
    I have used a hdmi cable to connect my lcd (which is connected with my speakers) with my nvida 275 gtx grafic card. I can not get the sound output to work. The hardware itself is working probably - I tested it under windows. Currently I am running Kubuntu 9.10 64 with Nvidia 190.53. The sound output worked fine before I installed the hdmi connection. (German output - i can change it, if you tell me how :)) aplay -l **** Liste von PLAYBACK Geräten **** Karte 0: Intel [HDA Intel], Gerät 0: ALC889A Analog [ALC889A Analog] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 Karte 0: Intel [HDA Intel], Gerät 1: ALC889A Digital [ALC889A Digital] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 aplay -L front:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog Front speakers surround40:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=Intel,DEV=0 HDA Intel, ALC889A Digital IEC958 (S/PDIF) Digital Audio Output null Discard all samples (playback) or generate zero samples (capture) pulse Playback/recording through the PulseAudio sound server And i disabled mute in kmix an all channels :) Edit: lspci -v ... 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) Subsystem: Giga-byte Technology Device a022 Flags: bus master, fast devsel, latency 0, IRQ 22 Memory at ea400000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel <?> Capabilities: [130] Root Complex Link <?> Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel ... cat /proc/asound/version Advanced Linux Sound Architecture Driver Version 1.0.20. lsmod | grep snd_hda_intel snd_hda_intel 31880 2 snd_hda_codec 87584 2 snd_hda_codec_realtek,snd_hda_intel snd_pcm 93160 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss snd 77096 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device snd_page_alloc 10928 2 snd_hda_intel,snd_pcm I think I am missing the something-hdmi module? Is there such a thing?

    Read the article

  • quad sli with gtx 690 not working

    - by Moaadh
    I have two cards GTX 690 (dual core). I did the Sli successfully. Nvidia control panel acknowledges the two cards as quad Sli. However, the problem is that Windows 7 64-bit Ultimate is showing me the graph memory size as 4 GB while it is supposed to be 8 GB because of the Sli. Also the benchmark from all software is giving me a very low score compared to some other guy's benchmark on YouTube. It gives me a big headache. Does anyone know why this is happening? If so, how can I get Windows 7 to recognize all 8 GB of memory? Thanks for your help in advance. My computer specifications: (Processor: Intel Core i7-3930k @3.2GHz(12CPUs))--- (Memory: 65536 MB Ram 1866 MHz)-- (OS: Windows 7 Ultimate 64-bit)-- (OCZ 240GB as SSD PCIe drive for booting and storage disk)-- (DirextX version: DirectX 11)-- (VGA Card: 2 X EVGA GTX 690 Dual GPU. Each GPU is 2 GB, so total memory should be 8 GB.)-- (MotherBoard: ASUS Rampage IV Extreme)-- Others with lesser specifications get a 2500 score in heaven benchmark while I get 1501 as if it is one card.

    Read the article

  • Why just splitting an Ethernet cable does not work?

    - by Sin Jeong-hun
    I thought the Ethernet is logically one-line communication bus (for argument's sake, I am excluding hubs). All machines attached in the bus hears the same signals and the machines themselves try to avoid collisions by randomly backing off. http://computer.howstuffworks.com/ethernet6.htm If so, why splitting one Ethernet line from my home router into two and connecting two computers would not work? Why do I have to add a switch to it? *What the Internet said would not work. [4 port home router] ------[one Ethernet cable]-----[simple splitter]======[two computers] *What the Internet said I should do [4 port home router] ------[one Ethernet cable]-----[switch]======[two computers] Is this because of the signal degradation (reduced electric current)? Thank you for all the answers! The reason why I did not just use the two ports of my home router is... The 4-port gigabit router is in my room and I had put a computer in another room (also my room, though). Since wired network is far more reliable and secure, I had bought a long Ethernet cable and and connected the computer to the router. Now I was thinking about adding another computer to that room. I could buy another long Ethernet cable, but then there will be two cables between the rooms. The one line already is a minor annoyance, so I thought if I could share the one line between the two computers in that room. A switch would work, but it requires power and is a little bit pricey. That is why I wondered why it would not work to simply split the physical Ethernet cable. Apparently I do not completely understand how Ethernet and a switch work. I just have some bit of knowledge I heard in my college class.

    Read the article

  • Screen randomly goes blue/black/white

    - by FubsyGamer
    Problem Randomly, while using my computer, the monitor goes dark grey/almost black, or it goes white with faint grey vertical lines, or it goes blue with black vertical lines. It's as if the computer powers off. People tell me I sign out of Skype, Spotify stops playing when it happens, etc. When I look at the tower, it doesn't seem like it's off at all. Nothing changes, fans are spinning, lights are on, etc. If you were only looking at the tower, you'd never know there was a problem The only way I can get it to come back up is to push and hold the power button and turn it off, then back on This never happens while I'm playing video games. I've done 5-6 hour sessions of League of Legends, and it doesn't do anything When I'm just browsing the web, reading email, checking Reddit, etc, it happens all the time. It can happen multiple times in a session, it usually takes only about 5 minutes from the time I start browsing to when the computer crashes This started happening after I moved to a new apartment (this has to be relevant somehow, it was not happening where I lived before) There is nothing in the crash logs or event logs System Specs i5 2500k CPU AMD Radeon 6800 GPU Gigabyte z68a-d3h-b3 motherboard WD VelociRaptor 1 TB HDD Screenshots Device manager About screen Things I have tried I was getting a WMI Error in my event logs, but I fixed it using Microsoft's fix, KB 2545227 I was using Windows 8. I wiped the HDD and downgraded to Windows 7 64 bit I took out the video card and used a can of air to totally clean out the video card, all fans, and the inside of the computer in general. I made sure all of the video card pins were fine, then reconnected it I tried to update my motherboard BIOS, but anything I downloaded from Gigabyte was only for 32 bit machines, not 64. I don't even know how to tell what my motherboard BIOS is at right now I am using a power strip, and anything else connected to it works just fine If I re-seat the monitor cable while this is happening, nothing changes Please, help me. I've been battling this for several weeks now, and it's so frustrating it makes me not even want to use the computer.

    Read the article

  • What would cause my SendMail server not to acknowledge receiving a TCP Sequence?

    - by Mike B
    My TCP/IP Stack knowledge is a little rusty so please bear with me.... I have a CentOS 5.7 server with SendMail and am having seeing intermittent timeout issues sending email (particularly larger email) to other remote domains. It doesn't happen with all attachments or recipient domains. Just some. After some extended troubleshooting, I think I've narrowed it down to TCP Sequences not being acknowledged. Here's a breakdown of the TCP session from a packet capture I collected directly on my MTA (fooMTA): Packet 1 - 11: Standard TCP handshake followed by initial SMTP conversation. No errors. Packet #12 Recipient MTA: TCP sequence 231. Ack 91. Packet #13 FooMTA: TCP sequence 91. Ack 305. Packet #14 FooMTA: TCP sequence 1115. Ack 305. Packet #15 Recipient MTA: TCP sequence 305. Ack 2495. Packet #16 FooMTA: TCP sequence 2495. Ack 305. Packet #17 FooMTA: TCP sequence 5255. Ack 305. Packet #18: Recipient MTA: TCP sequence 305. Ack 5255. Packet #19: FooMTA: TCP sequence 6635. Ack 305. Packet #20: FooMTA: TCP sequence 8015. Ack 305. Packet #21: Recipient MTA: TCP Sequence 305. Ack 8015. Packet #22: FooMTA: TCP Sequence 10775. Ack 305. Packet #23: FooMTA: TCP Sequence 13535. Ack 305. Packet #24: Recipient MTA: TCP sequence 305. Ack 10775 Packet #25: FooMTA: TCP Sequence 14915. Ack 305 It keeps going like this with my server still thinking it hasn’t received sequence 305… in response the remote side eventually retransmits its prior data thinking that it never arrived. Eventually the gap gets so large that no new data is sent and the remote MTA keeps retransmitting old stuff. This contributes to an exponential backoff and eventually the remote side gives up. What’s strange to me is that I see the “missing” TCP sequence (305 in this case) arriving back to my server (via a packet capture collected directly from fooMTA) So I don’t get why my server keeps asking for it. Could this be firewall related? What would be the next step in troubleshooting?

    Read the article

  • linux networking: how to redirect incoming connections from old server to new server?

    - by aliz
    hi I'm in the process of moving my old server to a new server, but i will keep the old server running for database replication and load balancing, etc. each server has a separate internet connection with a static ip, and they are connected through a local Ethernet connection. I've got Ubuntu 8.04 32-bit running on old server and Debian 6.0 64-bit on new one. shorewall firewall is installed on both servers. there are some outdoor devices which are periodically sending data to port 43597 for old server IP address. I can run multiple instances of the network service which is responsible for receiving data from devices on a server but on different ports. here's the question: how can I run the service on new server and have connections coming to old server redirected to it, and new devices can still connect to new server's IP address preferably on the same port and same service? until all devices get updated to send to new server. I've tried a shorewall DNAT rule, but seems like new server's default route should be changed to ethernet connection, which breaks other things. I also found about redir utility, but still haven't tried it. is there any best practice or simple solution for such a scenario, i'm not aware of? thanks in advance.

    Read the article

  • 2 routers at home- how to connect with VNC?

    - by Charles Leviton
    I have two routers at home. First router is upstairs and is connected to the cable modem. 2nd router is downstairs and acts as "signal booster" for the 1st router. Devices connected to the upstairs router have IP addresses of the form 192.168.1.n Devices connected to the upstairs router have IP addresses of the form 192.168.2.n. I blindly followed instructions from a website to do this set up, just glad it works! Upstairs I have a PC running Win 7 64 bit. Its assigned IP is 192.168.1.7. I have a VNC viewer running on this. Downstairs I have a 2nd PC running Vista 32 Home edition bit that is connected to the 2nd router and has IP Address 192.168.2.114. VNC server is running on this. It's listening on 5900. There is no firewall. When I try to connect to this downstairs PC from upstairs it fails with message "Failed to connect to server". I cannot ping to this either. If I try to connect to this downstairs PC using VNC Viewer from another computer that's connected to the same downstairs router then it works like a charm. So what's the work around if the viewer is on a different "network"? I don't have any problems doing remote desktop connection from the downstairs PC to the upstairs PC even if they are connected to different routers. Router information- Upstairs- ASUS RTN13U, downstairs- DD-WRT v24 RC-5 Thanks! P.S. I posted this on the Ultra VNC forum as well but that doesn't seem to have a lot of activity, so taking the liberty to multipost.

    Read the article

  • File corruption (bad checksums) in large files copied to VMware guest

    - by AllanA
    In setting up a development lab, I've got a desktop system running ESXi 4.1.0 (free license) on SATA RAID 0 (already purchased and configured when I started this job; I'm open to hardware input as it pertains to my problem.) Its guests so far include two Win2008 Server R2 64-bit VMs and on Ubuntu 10.04 64-bit VM. I'm installing onto the Windows servers. We've been copying off some fairly large files (over a gigabyte) for an installation, hoping to install more quickly from a (virtual) hard drive than from the network for from BD-ROM. The problem is that they keep coming up with different checksums from the originals. The file sizes are the same, but md5sum reports different numbers (and so does the installer, as it refuses to continue when the checksums don't match.) I've tried copying directly from the BD-ROM (attaching the OS drive to the host system's physical drive). I've tried copying the large files onto a co-worker's Windows machine from his Blu-Ray drive; when I do that, the checksums match. But when I copy from his machine to the VM guest over a network share, the checksums no longer match. Thinking this meant a corrupt destination drive, I deleted it in vSphere and added another freshly created drive. The problem persists. I'm not sure what to try next.

    Read the article

  • Constantly visible notification and access icon for Empathy in Gnome 3

    - by aef
    Since a short while I'm using Ubuntu Oneiric Ocelot (11.10) with gnome-shell (Gnome 3) and I'm trying to get accustomed to the default Empathy Instant Messaging client. One mayor problem for me (coming from Gnome 2 and Psi) is that there is no constantly visible icon which makes it clear (for example by changing its icon or showing an animation) if there are incoming messages which I did not read already and which lets me jump into them with one click. Also I'm missing a way to bring up the contact list or hide it away with a click. I sometimes have real problems even figuring out how to even open the contact list up again. Is there a Gnome 3 extension or some other trick available to display such a notifier in the top bar? I'm talking about something just like the sound and network controls which are already located there. I know that there are notifications in the lower notification area (former system tray), but as it is only visible as I move the mouse in the lower right corner of the screen, its useless for me.

    Read the article

  • Updating ASUS BIOS on Windows 7 64bit

    - by joesavage
    I've recently decided that I want to try and utilize my two graphics cards so that I can have a dual monitor setup. Unfortunately Windows only seems to notice my most recent graphics card installation - and so I've been told that I should look into my BIOS and try to enable two graphics cards. I could not find this setting anywhere in my M2N68-AM Plus v0210 BIOS. After some further research I figured that I should perhaps upgrade my BIOS, so I searched and managed to download the latest version (v1804) as a ROM file. However I am having difficulty figuring out how to install it. I've tried using the Asus EZFlash feature built into my BIOS, but when trying to load up a variety of different ROMs that are for my motherboard/BIOS I get the error: Boot block in file is not valid! I'm not totally sure what I should do to fix this, so I'm looking into other methods of upgrading my BIOS - however I can't really find any solutions that seem to work. Asus Update is for 32-bit only, AFUDOS doesn't appear to work on my Windows 7 64-bit system (I think it's supposed to run in DOS or something - but that just sounds confusing since I know nothing about DOS). Could anybody help me with this?

    Read the article

  • Windows 8 install from USB freezes

    - by Rafael Almeida
    I'm trying to install Windows 8 from an 8GB Kingston Data Traveler. I'm currently using the Windows 7 USB DVD Download Tool to put the iso into the flash drive. It copies the files, but in the end it says it 'had a problem with bootsect' and could not make the flash drive bootable. This seems to be because my current system is Windows 7 32bits, and the bootsect.exe in the ISO is a 64-bit executable. Then I downloaded the 32-bit bootsect.exe and made the drive bootable by running: bootsect /nt60 E: /mbr Then I restarted and managed to boot via the flash drive, but now everything is very slow. It takes about two minutes for the initial black screen with the Windows logo and the spinner go away, then it goes to a purple-ish blank screen that stays on for about five more minutes and then it finally shows a dialog asking for the installation, date/time and keyboard languages. I input then, click "Install Now" and it takes about three more minutes with a "Setup is starting" screen. After that, the PC apparently reboots, the CPU fan speeds up considerably, and there's no video and nothing more happens even after more than ten minutes. What is happening? I already tried using another USB port and even installing from a Samsung G3 Station 2TB external hard disk, but the same thing happens. The file transfer speed to the Kingston drive was about only 3 megabytes per second.

    Read the article

< Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >