Search Results

Search found 16499 results on 660 pages for 'off rhoden'.

Page 463/660 | < Previous Page | 459 460 461 462 463 464 465 466 467 468 469 470  | Next Page >

• Poor Write Performance in VM inside Proxmox PVE 2.0

  - by sorsenne

  I am running a PVE 2.0 on a decent Hardware (2 SATA HDDs as RAID1, 12GB RAM, i7 CPU) but the I/O Performance is very poor inside the VM (Ubuntu 11.10 Server). The very same VM was copied to another Server running simply Ubuntu Server with KVM and had better I/O Perf. this is how the HDD is shown in the Guest: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) ata1.00: ATA-8: ST3000DM001-9YN166, CC49, max UDMA/133 ata1.00: 5860533168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA ST3000DM001-9YN1 CC49 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 0:0:0:0: [sda] 4096-byte physical blocks sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA I tested with DD: $ dd bs=1M count=128 if=/dev/zero of=test conv=fdatasync 128+0 records in 128+0 records out 134217728 bytes (134 MB) copied, 19.2222 s, 7.0 MB/s on the Host, this same Test will result with 156 MB/s in average. PS: I am using VirtIO and see no error in dmesg.

  Read the article

• Why would Windows use slower network interface despite route metrics?

  - by tim11g

  On my previous notebook, the Dell/Broadcom wireless adapter had an option to automatically disable wireless when a wired network is connected, so I never dealt with multiple active interfaces. My current system has an Intel wireless adapter, and they apparently haven't figured out how to turn it off when there is a wired connection. Unless I explicitly remember to disable wireless when docked, the connection is active. That shouldn't be a problem (in theory), since the route metric will cause traffic to go over the fastest network (as indicated by the lowest metric in the routing table). Apparently not - I'm running a backup and seeing the throughput at 25Mbps or so (which is consistent with 802.11g) when a perfectly good Gigabit Ethernet interface is also connected. IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.254 192.168.1.104 10 0.0.0.0 0.0.0.0 192.168.1.254 192.168.1.109 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 Windows has correctly identified the Ethernet interface (.104) and assigned it the lower (preferred) metric. So the Ethernet interface should be used exclusively, right? Why is the Ethernet connection not being used? What other factors are involved? (This is with Windows 7 if it makes a difference)

  Read the article

• Wireless USB keyboard and mouse can wake system, but then receiver is inactive

  - by BlueMonkMN

  I have a Microsoft brand USB device that acts as a receiver for a wireless Microsoft Keyboard and a wireless Mouse. When it's operating normally, there are LEDs on the device indicating Caps Lock, Num Lock and Function Lock, of which the latter 2 are usually lit. It is plugged into a Dell Isnpiron 531 with Windows 7 32-bit running on an AMD Athlon 64 X2 Dual Core processor 5000+. When the computer goes to sleep (the power indicator on the main box is flashing), I can wake it by moving the mouse. So far all is good. However, something changed in, I think, the past couple weeks (I suspect due to a Microsoft driver update problem). Before the change, after waking the computer, everything would operate normally as far as I could tell, but now after waking the computer, the receiver has no lights on, and the keyboard and mouse are completely unresponsive (which is odd, considering the mouse woke up the computer). There is a button on the receiver that's supposed to reset the wireless connection and flash the lights while it does so, but it has no effect in this state. It's like the receiver doesn't have power (but how would the system know I moved the mouse, unless the power was on until it woke up?). I have checked the BIOS/CMOS settings or whatever you call them, and did not see anything related to USB in the power management section. I have checked Windows 7 device manager and ensured that all the USB Root Hub devices have the setting unchecked for allowing the USB power to be turned off. Like I said, this was working before, and the only thing I can think of that's changed is applying Windows Updates.

  Read the article

• Purge print driver cache on windows 7 with powershell script

  - by Doltknuckle

  [Background] We have been having trouble with our network clients suddenly being unable to print. They get an odd error with a hex code. We determined that something in the driver was messed up and we could resolve the issue by clearing the driver cache and reinstalling the driver. This happens to random computers every so often. We're assuming this is a bug with the latest Dell 2330dn driver since that is the only model that has this problem. [Problem] What we are looking to do is write a Powershell script that would clear the driver cache and redownload the driver. I see a ton of scripts out there to manage queues, servers, and ports, but nothing for local driver cache management. [Current Workaround] Since we have to do this manually, I'll write out the steps so you know what we want this script to replicate. Disable print spooler Restart machine Delete contents of: C:\windows\system32\spool\drivers\w32x86 Enable print spooler and start service. Delete the network printer object and re-add network printer off of server. [Request] I'm good enough with powershell to translate the above workaround into a pair of scripts. I'd like to find a more elegant solution then my current workaround. Any suggestions?

  Read the article

• Why does cpuinfo report that my frequency is slower?

  - by Avery Chan

  My machine is running off of a AMD Sempron(tm) X2 190 Processor. According the marketing copy, it should be running at around 2.5 Ghz. Why is the cpu speed being reported as something lower? Spec description (in Chinese) $ cat /proc/cpuinfo processor : 0 vendor_id : AuthenticAMD cpu family : 16 model : 6 model name : AMD Sempron(tm) X2 190 Processor stepping : 3 microcode : 0x10000c8 cpu MHz : 800.000 cache size : 512 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm 3dnowext 3dnow constant_tsc rep_good nopl nonstop_tsc extd_apicid pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs skinit wdt npt lbrv svm_lock nrip_save bogomips : 5022.89 TLB size : 1024 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm stc 100mhzsteps hwpstate processor : 1 vendor_id : AuthenticAMD cpu family : 16 model : 6 model name : AMD Sempron(tm) X2 190 Processor stepping : 3 microcode : 0x10000c8 cpu MHz : 800.000 cache size : 512 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm 3dnowext 3dnow constant_tsc rep_good nopl nonstop_tsc extd_apicid pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs skinit wdt npt lbrv svm_lock nrip_save bogomips : 5022.82 TLB size : 1024 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm stc 100mhzsteps hwpstate

  Read the article

• Windows Vista: Screen remains darkened for 30-60 seconds *after* UAC prompt

  - by sf2k

  Fixing someone's Vista computer. Process: I click any program or process that opens a User Account Control prompt. Screen goes dim so you may hit Continue to perform a secure user action. I click Continue Screen goes black for 30 seconds to 1 minute while you wait for the screen to return. In another example I click Cancel and screen still then goes black for 30 seconds to a minute. In that timeframe a chime goes off while you wait. (No chime if it was being cancelled.) Then screen comes back to continue with whatever. Something is occurring after the UAC prompt. Considering everything is practically a UAC acceptance this can get pretty annoying pretty quickly. Laptop has external monitor to regular external plug. Works fine. Laptop also has USB IOGEAR additional external video card. This is problematic but when unplugged same above behaviour occurs. I've ruled out monitor interference since same blackout after the UAC prompt appears with external monitors plugged in or when rebooted with no external monitors. Any suggestions on how to address this problem?

  Read the article

• Apache is sending php files to my browser instead of parsing

  - by justen doherty

  I have to set up PHP on an existing web host. I have made a virtual host entry, but for some reason Apache is sending the PHP to the browser instead of parsing.. from googling around it looks like it's a problem with the mimetypes, but I'm not an Apache expert by any means, so if anyone could help it would be appreciated... I have the following in my httpd.conf: AddHandler php5-script php DirectoryIndex index.html index.phtml index.php index.phps AddType application/x-httpd-php .phtml AddType application/x-httpd-php .php AddType application/x-httpd-php-source .phps The PHP module is loaded into Apache: /usr/sbin/apachectl -M Loaded Modules: core_module (static) mpm_prefork_module (static) http_module (static) so_module (static) auth_basic_module (shared) auth_digest_module (shared) authn_file_module (shared) authn_alias_module (shared) authn_anon_module (shared) authn_dbm_module (shared) authn_default_module (shared) authz_host_module (shared) authz_user_module (shared) authz_owner_module (shared) authz_groupfile_module (shared) authz_dbm_module (shared) authz_default_module (shared) ldap_module (shared) authnz_ldap_module (shared) include_module (shared) log_config_module (shared) logio_module (shared) env_module (shared) ext_filter_module (shared) mime_magic_module (shared) expires_module (shared) deflate_module (shared) headers_module (shared) usertrack_module (shared) setenvif_module (shared) mime_module (shared) dav_module (shared) status_module (shared) autoindex_module (shared) info_module (shared) dav_fs_module (shared) vhost_alias_module (shared) negotiation_module (shared) dir_module (shared) actions_module (shared) speling_module (shared) userdir_module (shared) alias_module (shared) rewrite_module (shared) proxy_module (shared) proxy_balancer_module (shared) proxy_ftp_module (shared) proxy_http_module (shared) proxy_connect_module (shared) cache_module (shared) suexec_module (shared) disk_cache_module (shared) file_cache_module (shared) mem_cache_module (shared) cgi_module (shared) version_module (shared) fcgid_module (shared) perl_module (shared) php5_module (shared) proxy_ajp_module (shared) ssl_module (shared) And this is my virtual host entry: <VirtualHost 10.16.140.113:80> ServerName viridor-cms.co.uk ServerAlias www.viridor-cms.co.uk UseCanonicalName Off DocumentRoot /var/www/vhosts/viridor-cms.co.uk/httpdocs CustomLog /var/www/vhosts/viridor-cms.co.uk/cms-access_log common ErrorLog /var/www/vhosts/viridor-cms.co.uk/cms-error_log DirectoryIndex index.php index.html <IfModule sapi_apache2.c> php_admin_flag engine on php_admin_flag safe_mode on </IfModule> <IfModule mod_php5.c> php_admin_flag engine on php_admin_flag safe_mode on </IfModule> AddType application/x-httpd-php .php AddType application/x-httpd-php-source .phps </VirtualHost> Please help, my head is so sore from banging it against the table and the wall!

  Read the article

• Cannot print certain colours on Ubuntu with HP Laser Printer

  - by ILMV

  We have a load of machines running Ubuntu in our office, they are either on 8.04 or 9.10. We have a server which connects a HP JetDirect that connects to a HP 3550 Colour Laser printer using CUPS. The problem we are having is we cannot print red, magenta or yellow at 100%, I've got a picture of the Ubuntu test page to demonstrate my problem: This is obviously a pretty big problem as we are constantly receiving documents with these colours and cannot successfully print them off, we cannot just switch the grayscale, our business depends on being able to print colour (seems trivial but we handle lots of artwork). We're using the recommended driver HP Color LaserJet 3550 footmatic/pxljr (recommended), there is another driver in the list labelled HP Color LaserJet 3550 footmatic/hpijs. These are production printers so need to make sure any setting change won't kick is in the nuts. It would appear HPIJS is for HP Inkjets, makes sense I guess. The problem doesn't occur in Windows. RESOLVED I've managed to solve the problem, I did indeed use the HPIJS driver (apparently for inkjets) but it seems to have worked, we're going to roll with it for now to see how we get on with it.

  Read the article

• Calendar sharing between unrelated Domains

  - by vlannoob

  I have a 'request' from one of the 'big guys' that has me scratching my head a bit. He is one of our Executives that also is a board member of several other organistations, so he floats around between 4 different unrelated companies, each with their own domains, Exchange setup etc. He has domain accounts in each organisation. He has an iPad with multiple Exchange accounts so he can see all his calendars which works Ok for him - Apple calendaring bugs/flaws aside. What he wants is the ability for 'reception staff' at each organisation to 'see' all his calendars as they are booking things for him in their respective organisations calendars without it conflicting with bookings made in his calendars by other organisations......you with me?? So for example: Company A books a meeting into his Comapny A calendar at 9am Monday and Company B books him a meeting in his Company B Calendar at 9:15am Monday on the other side of town and of course Company C has him booked in all day Monday on their Company C calendar. He gets all those on his iPad but he would like either a 'global' calendar all can see and book into or the ability for receptionists at Company's A,B and C to see all the Calendars to avoid these kind of conflicts. I told him to 'go away' straight off the bat, I don't control anything to do with the other companies or know their infrastructure. And quite frankly I don't want any part of it...but he's whining and he's high enough up the food chain that I can't ignore him forever. I'm open to suggestions. Is there any third party software/services that can facilitiate this kind of setup? I really don't want to be creating users in my AD structure to people not ion our organisation so they can get access to his calendar and I am sure there sysadmins feel the same. As usual - any advice is greatly appreciated ;)

  Read the article

• vmware vmdk disk problem

  - by dmtr

  I have a VMware ESXi 4 server and 2 storage servers (mounted via nfs). Between the storage servers (Fedora 14) is a drbd cluster (dual primary) and ocfs2 filesystem; also every server has a local partition with an ext4 filesystem, both are mounted via nfs on the esxi server. When I tried to copy a virtual machine (naturally it was powered off) from the ext4 partition to the ocfs2 partition, the vmdk total file size is different, but the md5sum is the same. On the ext4 partition: # ls -la total 28492228 -rw------- 1 root root 42949672960 Jan 14 14:46 disk-flat.vmdk # md5sum disk-flat.vmdk 0eaebe3138beb32f54ea5de6dfe5a987 On the ocfs2 partition: # ls -la total 13974660 -rw------- 1 root root 42949672960 Jan 14 16:16 disk-flat.vmdk # md5sum disk-flat.vmdk 0eaebe3138beb32f54ea5de6dfe5a987 When I power on the virtual machine from the ocfs2 partition it dosn't work. I have a windows on the virtual machine and it freez?s after the windows logo. From the ext4 partition the virtual machine workes. I tested with linux (created and installed on ext4 partition and then copied to the ocfs2) and the same problem appears. When I create a virtual machine directly from ocfs2 partition, there are no problems. I tried to copy via vSphere client, and I have the same problem. Any suggestions?

  Read the article

• Desktop.ini Issues/Confusion

  - by EpicDavi

  BACKSTORY: I was out of town for a while and I forgot to turn my computer off. When I came back I saw that a desktop.ini file was on my desktop (using Windows 7). I thought that was odd because I knew it was a system file and it usually didn't show up due to the fact that I had disable the feature to show system files. Also it wasn't translucent like the other system files. I went to my control panel and saw that the "Hide protected operating system files" was indeed enabled. This puzzled me so I disabled the setting and another one was on my desktop like it usually is hidden. So now I have to desktop.ini files on my desktop: one hidden and one not hidden. I am doing an antivirus check to see if anything was going on and I will give an update soon. I am pretty sure these files are harmless and could be deleted but I would rather get another person's opinion on the subject. Thanks! UPDATE: I did an anti-virus scan and it seems I have no problems. It is odd because the file seems to maintain system file properties such as not being able to be edited and other things. Also I have tried restarting my computer and it is still not hidden. So the question remains: What should I do with the file and what caused it?

  Read the article

• Apache ProxyPassReverse and https

  - by joshuaball

  Hi, I would like to map all traffic on 80 and 443 from foo.com to an internal server: 192.168.1.101. I have a VirtualHost (Apache 2.2 on Ubuntu) setup as follows (note, I had to break up the hyperlinks below because I am a 'new user'): <VirtualHost *:80> ServerName foo.com ServerAlias *.foo.com ProxyRequests Off ProxyPreserveHost On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / http://192.168.1.101/ ProxyPassReverse / http://192.168.1.101/ </VirtualHost> And that works great for http traffic. However, I can't seem to do the same thing for https. I have tried: Changing VirtualHost *:80 to * - but that doesn't work (I need it http-http and https-https) Creating a new VirtualHost entry for *:443 that redirects to http://192.168.1.101/, but that fails as well (browser timeouts) I did some searching, here and elsewhere, and the closest question I could find was this, but that didn't quite answer it. Also, just out of curiosity, I tried mapping all ports to https (by changing the two ProxyPass lines from http to https (and removing the :80 from VH), and that didn't work either. How would you do that as well? Any thoughts? Thanks in advance.

  Read the article

• Error 53 - The network path was not found.

  - by Jack

  I have a machine in my Active Directory Domain that I can no longer "net view" from other machines in the domain. This is a Windows XP Pro machine. It is hosting a VMWare virtual of my Domain Controller. If I attempt to net view [machine name] I get system error 53, The network path was not found. This is not a DNS issue, the same thing happens with the machine's IP. I don't think it's a firewall issue, I turned the firewall off on this machine. As I mentioned, it has worked in the past, and then stopped for no reason that I can see. I (intentionally) didn't change the software. I CAN get to the VMs hosted on this machine, can connect to their shares, net view them, etc. All other machines can see each other. In fact, the problem machine can see other machines and access their shares just fine. I tried removing the machine from the domain and re-adding it. I tried deleting the shares and recreating them. Not sure how to troubleshoot this any further. Any ideas?

  Read the article

• Asus n61Ja notebook bios update

  - by zKs

  I wanted to update the bios, with an official bios update, from version 207 to 211. I didn't use winflash, I used easyflash in the bios. Everything seemed to be going okay; it deleted the old files, wrote the new ones, verified the new ones. Then it said: shutdown in/after 2 seconds and it shut down. Then nothing happened anymore. Power button completely unresponsive. The battery light was still on, and I'm not sure if I should've just waited... I didn't though, I thought I had to remove the battery, take the power off completely to be able to start it up again. So I'm wondering: what are my options here? My warranty expired and I don't really have the money to send it in and pay hundreds of bucks on repairs. Is there anything I can try? CMOS battery reset? Anything??? Please help me out! I would be very grateful :) ps. What was sort of odd btw, was that easyflash said something like that it was an unsigned bios and if I wanted to flash it anymore, if i wanted to 'force' it or something. It was with 100% certainty the correct update from the Asus.com support site, so I didn't take that 'warning' seriously.

  Read the article

• Windows CE restores default configuration after restart (Motorola MC3190)

  - by jarek

  Good morning, everyone! I have a problem with Motorola MC3190 hand scanner running on Windows CE. I've got few of those to make a new program for some kind of warehouse. There is already installed program which have been used by the customers before, so I delete this one and instead I install my new software which I've just made. It is running very well, but when I take out the battery and leave the device for entire night without power supply, it restores the whole configuration, so the old program is back, the wireless configuration is back and... Yeah. The scanner is restored to the configuration which was running when I received it few weeks ago. What I want to do is to set the whole configuration of the scanner so after a long power-off my program and my configuration will be restored. I truly believe someone knows how to do it. The time is running out, and I believe that the customer will be kind of annoyed when he will change the battery and the program which he bought will be gone. ;-) Regards, Jarek

  Read the article

• ipv6 port 445 does not accept the request from a global type address

  - by blacktea

  I want to scan the port 445 in windows server 2003, but my scanner only have one type ipv6 address which is global not link-local. When I do this,I find that I can't find port 445 open. But I use the command "netstat -an" to assure the port 445 is listening. Finally I find this confusing phenomenon: 1.when I set a link-local ddress in my scanner, then it will work in scanning port 445. 2.when I only set a global address in my scanner, it doed not work. This means if a host with a link-local address use socket to send a syn packet to the port 445 in server 2003, it will receive a ack packet. But if with a global address it will receive a rst packet. Thus, I can't scan the port 445 in server 2003 with a global address. I need to know why? Can anybody help? And I use the netsh-firewall to check the exception and netsh-interface-ipv6 to turn off the firewall on the specific interface. Still can't establish the connection with port 445, do you have any ideal about this ?

  Read the article

• Mirror a Dropbox repository in Sharepoint and restrict access

  - by Dan Robson

  I'm looking for an elegant way to solve the following problem: My development team uses Dropbox for sharing documents amongst our immediate group. We'd like to put some of those documents into a SharePoint repository for the larger group to be able to access, as granting Dropbox access to the group at large is not ideal. However, we'd like to continue to be able to propagate changes to the SharePoint site simply by updating the files in Dropbox on our local client machines, and also vice versa - users granted access on SharePoint that update files in that workspace should be able to save their files and the changes should appear automatically on our client PC's. I've already done the organization of the folders so that in Dropbox, there exists a SharePoint folder that looks something like this: SharePoint ----Team --------Restricted Access Folders ----Organization --------Open Access Folders The Dropbox master account and the SharePoint master account are both set up on my file server. Unfortunately, Dropbox doesn't seem to allow syncing of folders anywhere above the \Dropbox\ part of the file system's hierarchy - or all I would have to do is find where the Sharepoint repository is maintained locally, and I'd be golden. So it seems I have to do some sort of 2-way synchronization between the Dropbox folder on the file server and the SharePoint folder on the file server. I messed around with Microsoft SyncToy, but it seems to be lacking in the area of real-time updating - and as much as I love rsync, I've had nothing but bad luck with it on Windows, and again, it has to be kicked off manually or through Task Scheduler - and I just have a feeling if I go down that route, it's only a matter of time before I get conflicts all over the place in either Dropbox, SharePoint, or both. I really want something that's going to watch both folders, and when one item changes, the other automatically updates in "real-time". It's quite possible I'm going down the entirely wrong route, which is why I'm asking the question. For simplicity's sake, I'll restate the goal: To be able to update Dropbox and have it viewable on the SharePoint site, or to update the SharePoint site and have it viewable in Dropbox. And since I'm a SharePoint noob, I'll also need help hiding the "Team" subfolder from everyone not in a specific group in AD.

  Read the article

• On a failing hard drive, I am able to view data but unable to copy it - why?

  - by Tom

  I have a 2.5" external hard drive that is failing. It's not making the expected 'clicking' noise that most hard drives and I am able to view the data, but I am unable to actually retrieve the data. I attempted to use SpinRite in order to access the data on the drive, but it didn't like the external drive. When I view the drive's property page, the drive shows that it's used space is at 100% and that it has 0 bytes available; however, the progress indicator under the drive icon in Windows Explorer shows that it's roughly 50% full (which is correct). When I attempt to run Windows' "Error Checking" tool and attempt to "scan for an attempt recovery of bad sectors," the tool begins to run then immediately closes with no error message. I am able to browse the contents of the drive using Windows Explorer. When I begin to try copying any given single file, the copy process begins, an indicator starts, and then the copy fails with no real error message. The Disk Management page in Computer Management under Control Panel also shows this drive has being 'Healthy.' I dropped the drive off at a data recovery store and they said that "The data seems to be intact, but an internal failure is preventing any information from being retrieved." They offered to provide me references to a data recovery specialist. I've also attempted to run CHKDSK on the drive (with and without arguments) but it returns the following error: The type of the filesystem is RAW. CHKDSK is not available for RAW drives. Before going the route of more expensive data recovery, I'm wondering if these symptoms sound familiar to anyone? Other questions... I'm willing to continue trying tools such as TestDisk and/or PhotoRec (as the majority of the data that I'd like to salvage are photos) but how long I should expect either tool to run given approximately 400GB of data? I'm also comfortable using Linux so I welcome any suggestions for utilities or tools and strategies with which you've had success.

  Read the article

• Connect bluetooth headphones both to PC and phone at the same time

  - by Sergiy Byelozyorov

  I have recently bought Philips SHB6110. Extract from the 13th page of manual: Therefore you can connect your Bluetooth stereo headset. with a Bluetooth stereo enabled phone to both listen to music and lead calls, or with a Bluetooth phone that does not support Bluetooth stereo (A2DP) to lead calls and at the same time to a Bluetooth audio device (Bluetooth enabled MP3 player, Bluetooth audio adapter etc.) to listen to music. Make sure to pair the phone first with your Bluetooth headset, then turn both the phone and headset off to then pair the Bluetooth audio device. With the SwitchStream feature you can listen to music and monitor your calls at the same time. Even while listening to music, you will hear a ring tone when receiving a call and can switch to the call simply by tapping the button. The manual however doesn't specify how do I connect to both device at the same time. I use Toshiba Satellite Pro P300-1CG laptop with Belkin Mini Bluetooth Adapter and Nokia N95 phone. Operating system is Windows 7 64-bit and I have Skype installed. Both phone and compute can be used for listening to music and talking on the phone (on PC via Skype). Best solution would be if I could connect to PC and phone as the same time and monitor calls both mobile and Skype calls while listening music from Winamp. If that is not possible, then I would like at least to be able to listen music from PC, while monitoring calls from mobile. So, please tell me how do I connect both PC and phone to headphones?

  Read the article

• copSSH and cygwin - Can't use windows style paths

  - by DrFredEdison

  I setup copSSH on one of my windows servers, and within the copSSH bash shell, I can't seem to use windows-style paths to remove and copy files. If I do try, I get the following: $ /bin/cp -r C:/Domains/_temp/collage_push/* C:/Domains/collage/ cygwin warning: MS-DOS style path detected: C:/Domains/_temp/collage_push/ Preferred POSIX equivalent is: /cygdrive/c/Domains/_temp/collage_push/ CYGWIN environment variable option "nodosfilewarning" turns off this warning. Consult the user's guide for more details about POSIX paths: http://cygwin.com/cygwin-ug-net/using.html#using-pathnames I have created a windows environment variable CYGWIN set to nodosfilewarning. It has no effect. I added export CYGWIN=nodosfilewarning to my .bashrc and doing a echo $CYGWIN in my ssh session confirms it is indeed getting set; yet again, it has no effect finally, I noted that when not doing my own export that CYGWIN contains "nontsec binmode" (no quotes), so I tried: export CYGWIN="nodosfilewarning nontsec binmode" in my .bashrc and still no dice. Older versions of CopSSH didn't have this issue. How can I actually override this error? I have a lot of scripts that already use windows-style paths, and I'd rather not change them if possible.

  Read the article

• Safe mode boot with no change on screen but ongoing hard disk activity - why?

  - by omatai

  I have a machine with a dying hard drive - bad sectors are starting to multiply :-( The first sign (24 hours ago) was that it had an unmountable boot volume. At this time, I tried booting to safe mode with command prompt, which worked, after which I rebooted normally and ran a chkdsk. It has since been working as well as I could expect, but slowly getting less reliable. So I scheduled another chkdsk on both partitions (C: - boot, D: - data), having freed up a lot of space on both partitions to give Windows a little more scope for repairs (hopefully?). I then rebooted. On reboot, it protested about the unmountable boot volume again, so I booted to safe mode. I got the same list of drivers loaded as yesterday, and then no change to the screen for the past 2 hours. However, I see a flickering hard drive indicator light - not always on, but seldom ever off. What is happening? Is the chkdsk that runs in safe mode one which produces nothing on the screen and so chkdsk could be doing its thing... or is Windows still trying (but failing) to boot into Safe Mode?

  Read the article

• QuickTime Player sounds much better than iTunes

  - by Gene Goykhman

  I am playing a 320 kpbs encoded music MP3 in iTunes and the sound is substantially worse than the exact same file played back in QuickTime Player (Max OS X 10.8.5). I have maxed out system volume and iTunes playback volume. I have disabled all the audio processing features in iTunes (equalization, sound enhancer, etc.) The audio coming from iTunes still sounds resampled and/or processed, whereas QuickTime Player appears to be playing it "as is". Even when I Get Info on the MP3 file in Finder and play it back directly from the Get Info window it sounds good. It's just iTunes that seems to be mangling the song. I can notice a difference on virtually all my music, so it's not just one particular MP3. I suspect the issue is that iTunes is doing some kind of audio processing but I can't find a way to turn it off. This is the newest iTunes (11.1), but the problem has probably been going on for a while... I just switched to decent earbuds and started noticing the difference. What's the best way to force iTunes to play back the file as-is, or as close as possible to how QuickTime Player/Finder would play it?

  Read the article

• What to do before connecting Ubuntu Server to the internet for the first time?

  - by CodeMonkey

  I just finished installing Ubuntu Server 12.10 on an Asus Eee PC 1000H (to be used as a home server/sandbox) from USB. I installed this software during installation: OpenSSH server LAMP server Samba file server Virtual Machine host I won't use 2, 3 or 4 for a while though. Can/should I turn these off somehow? I have turned home directory encryption on. Security updates are installed automatically. I have chosen a strong password for the single user. I have never plugged in the internet cable so far. Before doing so I'd like to ask: What can/should I do/install to increase security before connecting to the internet? Firewall? Fail2ban? Users/Passwords? Encryption? Enable/Disable functionality? etc. I'm sorry if you get this question a lot. I've searched around quite a while, but it still feels like I might overlook something important.

  Read the article

• Change which server mailbox is associated with in Exchange 2007

  - by tacos_tacos_tacos

  I have restored and mounted an EDB file onto a new Exchange 2007 Server. However, the old server is still online and although all the mailboxes I need are in the newly-mounted database, in Exchange 2007 System Manager it still shows that the mailbox is associated with the old server. If I try to "Move" the database it actually tries to copy the files from the old server to the new server, which is not necessary because they are already there - and produces and error about the mailbox on the destination already existing. How can I simply tell Exchange (AD?) to use the new server to find the mailbox rather than the old? Edit: I did the restore by taking the old server offline (turning off all Exchange services), copying EDB file to the new server, restoring it with eseutil, and mounting it to the new server. I did it this way in part because I didn't know a better way and in part because I couldn't use move-mailbox as the source location had a horrible Internet connection (which is why Exchange is being moved to the new location). I had to copy the EDB from the old server to a hard disk, go somewhere with a better Internet connection, upload the EDB to the new server.

  Read the article

• Cannot Install Bootcamp on Mac Fusion Drive

  - by user3377019

  I have two drive installed in my mid-2013 Macbook pro. It is running osx maverick. I set the two drives (an ssd and a regular HD) up using the fusion drive (following the diy fusion drive guides out there). I went ahead and created a 40gb partition to host my windows install. I removed the SSD, installed windows, then reinstalled the SSD. As soon as the ssd was placed back in the bootcamp partition stopped booting. I get a blinking cursor on a black screen. I checked out the partition info in disk utility and it appears that the windows partition is not marked bootable. Below is some info I managed to gather. I am wondering if there is a way to fix the partition table so my bootcamp will boot. /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *120.0 GB disk0 1: EFI EFI 209.7 MB disk0s1 2: Apple_CoreStorage 119.7 GB disk0s2 3: Apple_Boot Boot OS X 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *500.1 GB disk1 1: EFI EFI 209.7 MB disk1s1 2: Microsoft Basic Data BOOTCAMP 40.0 GB disk1s2 3: Apple_CoreStorage 459.2 GB disk1s3 4: Apple_Boot Boot OS X 650.0 MB disk1s4 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Macintosh HD *573.4 GB disk2 Name : BOOTCAMP Type : Partition Disk Identifier : disk1s2 Mount Point : /Volumes/BOOTCAMP File System : Windows NT File System (NTFS) Connection Bus : SATA Device Tree : IODeviceTree:/PCI0@0/SATA@1F,2/PRT1@1/PMP@0 Writable : No Universal Unique Identifier : 584BAED6-4C46-4F18-93B3-957F6E27003C Capacity : 40 GB (39,998,980,096 Bytes) Free Space : 16.34 GB (16,339,972,096 Bytes) Used : 23.66 GB (23,659,003,904 Bytes) Number of Files : 86,424 Number of Folders : 0 Owners Enabled : No Can Turn Owners Off : No Can Be Formatted : No Bootable : No Supports Journaling : No Journaled : No Disk Number : 1 Partition Number : 2

  Read the article

< Previous Page | 459 460 461 462 463 464 465 466 467 468 469 470  | Next Page >