Search Results

Search found 16021 results on 641 pages for 'mr nothing'.

Page 466/641 | < Previous Page | 462 463 464 465 466 467 468 469 470 471 472 473  | Next Page >

• Packet flooding while configuring a Debian L2TP/IPSec client?

  - by Joseph B.

  I'm currently at my wits end trying to configure an L2TP over IPSec VPN connection on my Debian using openswan and xl2tp box connecting to a server of unknown configuration. I've managed to successfully establish the connection and everything appears to be working well until I attempt to set the VPN connection as my default route, at which point I see a massive flood of packets simultaneously being transmitted (on the tune of ~1.5 GB in about 2min) until the server drops my connection. Prior to this network traffic on all my interfaces is minimal. According to iftop the majority of this traffic appears to be coming out of port 12, although I can't seem to figure out how to finger a specific process. If I instead just route traffic destined for 74.0.0.0/8 through it I'm able to access Google's servers through the VPN without issue. My xl2tp.conf file is: [lac vpn-nl] lns = example.vpn.com name = myusername pppoptfile = /etc/ppp/options.l2tpd.client My options.l2tpd.client file is: ipcp-accept-local ipcp-accept-remote refuse-eap require-mschap-v2 noccp noauth idle 1800 mtu 1410 mru 1410 usepeerdns lock name myusername password mypassword connect-delay 5000 And my routing table looks like: Destination Gateway Genmask Flags Metric Ref Use Iface 10.5.2.1 * 255.255.255.255 UH 0 0 0 ppp0 10.0.50.0 * 255.255.255.0 U 0 0 0 eth0 10.50.0.0 * 255.255.0.0 U 0 0 0 eth0 10.0.0.0 * 255.255.0.0 U 0 0 0 eth0 192.168.0.0 * 255.255.0.0 U 0 0 0 eth0 loopback * 255.0.0.0 U 0 0 0 lo default * 0.0.0.0 U 0 0 0 ppp0 I'm seeing absolutely nothing in auth.log and syslog during this time and can't seem to find any other log files it might be writing to. Any suggestions would be appreciated!

  Read the article

• reaching constant video bitrate by using ffmpeg

  - by sebastian

  We use ffmpeg and a transcoding script for transcoding and want to make some batch files which we can use for transcoding. For example I use a parameter called video_kbit and if I am writing in 30000 it should reach 30 Mbit. Of course if I use 6000 as parameter it should reach 6 MBit as well, so I have one script which reaches every video bitrate I want. As my settings are now, I only reach 18.1 Mbit. Only when I use 15000 as a parameter I am reaching my goal for a constant video bitrate of 15 MBit. If I use 8000 as parameter I get 10.1 MBit as a result. So under 15000, I get a higher bitrate and over 15000, I get a lower bitrate than I want. My presettings are: ffmpeg -threads "4" -i "$2" -f mp4 -c:v libx264 -crf 1 \ -bufsize 30000k -maxrate ${FC_PARAM_video_kbit}k \ -acodec libfaac -ac 2 -ab ${FC_PARAM_audio_kbit}k -ar 44100 \ -pix_fmt yuv420p -vf scale=${FC_PARAM_width}:${FC_PARAM_height} -y "$3" And I am using these parameters: FC_PARAM_video_kbit = 30000 FC_PARAM_audio_kbit = 192 FC_PARAM_width = 1920 FC_PARAM_height = 1080 I have tried using a higher bufsize and using profile:v and level settings, but nothing got me near the constant video bitrate of 30000 Mbit. Do you guys have any ideas or suggestions for a better way to reach my goal?

  Read the article

• iptables rule on INPUT between 2 ethernet cards on the same host

  - by user1495181

  I have 2 eth cards on the same host. Both connected directly with LAN cable. I set eth0 with ip - 192.168.1.2 I set eth1 with ip - 192.168.1.1 I set this rule: iptables -A INPUT -p tcp -j NFQUEUE --queue-num 0 There are no other rules. (I ran iptables -X,-F) I send TCP syn packet ( with c++ program by using raw socket) from 192.168.1.2 to 192.168.1.1 In wireshark i see that the packet received on eth0, but the iptables rule (above) dosnt apply for this packet. when i sent the packet to remote host and apply this rule on the remote host than it work correct. So, i guess that this is due to the fact that both eth cards exists the same host. . I need to create iptables INPUT rule for local eth card (dest and src on the same machine ). I need it for simplify test. Did i guess the problem correct? is there a way to bypass this? Ps - connected them via switch didn't help. the rule wasn't applied. Run on Ubuntu. TCDUMP show the packet: 10:48:42.365002 IP 192.168.1.2.38550 > 192.168.1.1.34298: Flags [S], seq 0, win 5840, length 0 but logging of iptables like this, has nothing: iptables -A INPUT -p tcp -j LOG --log-prefix '*****************' iptables -A OUTPUT -p tcp -j LOG --log-prefix '#################'

  Read the article

• Create custom launchers in GNOME 3

  - by hochl

  I'm using Debian testing, and I have been switched to GNOME 3 by the Debian update yesterday. I'm not very comfortable with the UI. I wanted to customize everything like I had it with GNOME 2, but I simply couldn't find any way to change preferences like I'm used to. I've digged some, but all answers I could find did not help me achieve my goals. So please, if anyone knows the solution to this I'd be thankful: 1) I want several launchers that launch terminals, with different arguments and different coloring/title. I have searched everything and there seems to be no menu, no right-click, nothing which is standard in any UI I know. How can I create several launchers in this bar on the left side that launch the same application, just with different parameters? With GNOME 2 this was a piece of cake. 2) I want to switch between different terminals using ALT-TAB. Right now, I'm always just getting to the same, already-opened terminal. When I open two terminals by simply creating the second one by issuing xterm &, I still get one Terminal entry with ALT-TAB, and I have to navigate with cursor keys or mouse wheel to select one of the two xterminals. Instead, I want to open a new terminal when I click the quick launch terminal icon from the bar on the left side of the screen and navigate through them like on KDE/GNOME 2/Windows/any reasonable UI. Can this be done? 3) Is there a trick to make bluetooth devices work like on GNOME 2? Right now, my BT keyboard won't pair anymore, which, as you can imagine, makes me pretty angry. and, if anything fails: 4) How can I switch back to GNOME 2 again? :-) Honestly, who did design this? What were they smoking? I feel like I'm not allowed to do anything except start one of any application that has an icon and just with the default parameters. That can't be true, right? I feel massively restrained by this stuff :(

  Read the article

• windows xp cannot access admin share

  - by barlop

  I have 3 systems. A,B,Compx all on xp. but comps A and B have an issue with Compx. Compx has network shares I can access. I can do \\compx and get some. But I cannot access the admin share c$ \\compx\c$ gives a login prompt, and I can't get any user/pass to work. I looked at permissions but don't see an issue. Nevertheless, I will describe what I see in the permissions. In the security tab of C, I have Administrators,creator owner,everyone,bob,system,users (6 things there) "creator owner" has nothing ticked, I can't seem to change that. If I tick so they all get ticked, and click apply, 2.5min and it's completed its opration and they all untick. Though this isn't the root of the problem. Since I get the same in the share I can access. In advanced, I see those 6 things, Administrators,creator owner,everyone,bob,system,users (6 things there) all "full control" all are "this folder, subfolders and files".. except creator owner, which is just subfolders and files only I look at the properties for the share I can see. looks the same, except in security..advanced, double clicking any of them the boxes are all ticked but greyed. That's not the problem though since I can access that share. So, I don't know what the problem is.

  Read the article

• SQL - an error occurred during the pre-login handshake

  - by Rivka

  Until yesterday evening, I was able to connect to my server from my local machine. Now, I get the following error: A connection was successfully established with the server, but then an error occurred during the pre-login handshake. (provider: SSL Provider, error: 0 - The wait operation timed out.) (.Net SqlClient Data Provider) Note, I can log on to the actual server with no problem. Yesterday, I installed IIS on my machine and set up a site using my IP address - don't know if this has anything to do. I did come across this article, followed the steps, but didn't seem to help. http://www.escapekeys.com/blog/index.cfm/2011/1/26/Microsoft-SQL-Server-Error-64-A-connection-was-successfully-established-with-the-server I also went through the following article, changed TC/IP settings, restarted, but nothing. http://blog.sqlauthority.com/2009/05/21/sql-server-fix-error-provider-named-pipes-provider-error-40-could-not-open-a-connection-to-sql-server-microsoft-sql-server-error/ Started trying suggestions from comments too but stopped when I realized I might be messing things up more. So, why is this happening / how can I fix?

  Read the article

• Recovering corrupted VB.NET Form file?

  - by Omega

  Good day. This question is directly related to this one I made here: http://stackoverflow.com/questions/4911099/there-is-no-editor-available-for-form1-vb-error There, I was working on my VB.NET 2010 Express application, I saved, then a blackout came and now, apparently, I can't view the designer nor code of my Form file (Form1.vb). On StackOverflow, I was recommended to check for the From1.vb file, and try to open it on Notepad. If nothing appeared, it would mean that my file was corrupted. I open it on Notepad, and I get a blank file. It is 27kb, but it only has blank spaces. So I assume it is corrupted. I was told this place was better for dealing with corrupted files, about techniques to recover them. I use Windows7, VB.NET 2010 Express. I run Windows7 on Parallels Desktop, Mac OS X. However, I do not believe that is the problem, most likely it was that damned blackout... this is the first time that happens to me. VB.NET worked just fine for me all time (about a month and half). Thank you.

  Read the article

• How to Dual-Boot Kali-Linux and Windows 8.1?

  - by Ceyhun

  I have Acer V3-772G 1 TB Harddisk. I shrinked my biggest partition in order to install Kali Linux. When installing Kali, GRUB couldn't detect windows 8 so I kept going on(I installed grub as my masterboot). After installed Kali there was no way to boot Windows 8.1, but booting Kali was OK with GRUB in legacy-BIOS. When I tried to change bios to UEFI it couldn't find any OS (took too much time, nearly 1 hour). So I tried to update GRUB with boot-repair within a Ubuntu Live USB. But after updating GRUB I terrified, in UEFI and Legacy mode grub couldn't find ANY OS (Both Kali and Windows) so I have no option other than using Ubuntu Live. I tried every possible options but nothing has worked for me. I tried rEFInd in UEFI mode it worked only for Kali. I still cannot boot my windows 8.1 . I considered to restore to factory setting with a Windows Rescue USB but kept telling me "No driver found". Please help me to dual boot or remove Kali and restore my Windows 8.1

  Read the article

• Why is my Toshiba Satellite L675D laptop not connecting to my HD TV using an HDMI cord?

  - by Akasha Eyre

  I'm having a problem connecting my Toshiba Satellite L675 laptop to my Samsung HD TV. I've done it before using an HDMI cord but now, for some odd reason, it's not connecting at all. My computer screen before would go completely black for a second & then come back & (with it being attached to the TV with the HDMI cord & it being on the proper channel) it would make a sound, come on & work beautifully. Now, I try hooking it up & it doesn't do anything. No black screen, no sound. The TV screen just says there's no connection & that I need to check out the power source. I'm still checking around, trying to find out if there's a virus in my computer (since my dad & I have the same computer & he can connect his to the TV with no problems), or if I deleted something that had to do with the connection. I've tried turning my computer off & letting it sit for a while, I've tried checking out other websites & have come up with nothing.

  Read the article

• What should I encrypt in Debian during install?

  - by ianfuture

  I have seen various guides and recommendations on web about how best to do this but nothing that clearly explains the best way and why. So I understand there is a need for part of Debian during install to be un-encrypted on its own partition to allow it to boot. Most info I have seen is call this /boot and set the boot flag. Next I believe the best approach is to create another partition out of all the rest of the disk space, encrypt this, then on top of that create a LVM and then within the LVM create my various partitions , name them , select size, and file system type. Can I include /swap in the encrypted LVM part ? Is this approach sound? If so what are the partitions I should use (this is going to be a minimal server install with a view to install as and when what I need for a dev server)? Finally how does the installer know what to put in each partition I define ? I appreciate there are more than one question but any help and suggestions would be appreciated. If further clarification is needed please mention in the comments . EDIT : 16/3/2010 After Richard Holloways reply I thought it relevant to add this info: The reasons why I want to do this are to explore maximising security on any server install and set up, due to interest in the area of Computer Security and Forensics. Also I am trying to peform the task as if it being performed in an enterprise situation. On a technical matter, once set up and configured with minimal packages and ssh this server will not physically be easy to access so I will only be entering via ssh. (Yes I know why encrypt something no one will ever be able to get their hands on? Because I can and I want to is the simple answer, but see above too).

  Read the article

• windows xp cannot access admin share

  - by barlop

  I have 3 systems. A,B,Compx all on xp. but comps A and B have an issue with Compx. Compx has network shares I can access. I can do \\compx and get some. But I cannot access the admin share c$ \\compx\c$ gives a login prompt, and I can't get any user/pass to work. I looked at permissions but don't see an issue. Nevertheless, I will describe what I see in the permissions. In the security tab of C, I have Administrators,creator owner,everyone,bob,system,users (6 things there) "creator owner" has nothing ticked, I can't seem to change that. If I tick so they all get ticked, and click apply, 2.5min and it's completed its opration and they all untick. Though this isn't the root of the problem. Since I get the same in the share I can access. In advanced, I see those 6 things, Administrators,creator owner,everyone,bob,system,users (6 things there) all "full control" all are "this folder, subfolders and files".. except creator owner, which is just subfolders and files only I look at the properties for the share I can see. looks the same, except in security..advanced, double clicking any of them the boxes are all ticked but greyed. That's not the problem though since I can access that share. So, I don't know what the problem is.

  Read the article

• VLC Crash when playing MKV files in Windows 7

  - by Phelios

  I'm not sure if the mkv file is corrupted, but when it is opened with VLC player, VLC loads up and displays nothing. Can't even close VLC after that. And also, VLC is running with 50% of the CPU. I have to use End Process to kill it. How do I know if the file is corrupted? How do I solve this? info from mediainfo Format : Matroska File size : 69.4 MiB Duration : 21mn 48s Overall bit rate : 445 Kbps Encoded date : UTC 2009-11-20 18:33:49 Writing application : mkvmerge v2.9.7 ('Tenderness') built on Jul 1 2009 18:43:35 Writing library : libebml v0.7.7 + libmatroska v0.8.1 Video ID : 1 Format : AVC Format/Info : Advanced Video Codec Format profile : [email protected] Format settings, CABAC : Yes Format settings, ReFrames : 2 frames Format settings, GOP : N=1 Codec ID : V_MPEG4/ISO/AVC Duration : 21mn 48s Width : 640 pixels Height : 352 pixels Display aspect ratio : 16:9 Frame rate : 23.976 fps Color space : YUV Chroma subsampling : 4:2:0 Bit depth : 8 bits Scan type : Progressive Audio ID : 2 Format : AAC Format/Info : Advanced Audio Codec Format profile : HE-AAC / LC Codec ID : A_AAC Duration : 21mn 48s Channel(s) : 2 channels Channel positions : Front: L R Sampling rate : 48.0 KHz / 24.0 KHz Compression mode : Lossy

  Read the article

• Formal separation marker of syslog events?

  - by Server Horror

  I've been looking at RFC5424 to find the formally specified marker that will end a syslog event. Unfortunately I couldn't find it. So If I wanted to implement some small syslog server that reacts on certain messages what is the marker that ends a message (yes commonly an event is a single line, but I just couldn't find it in the specification) Clarification: I call it event because I associate a message with a single line. An event could possibly be some thing like Type: foo Source: webservers whereas a message to me is this: Type: foo Source: webservers http://tools.ietf.org/html/rfc5424#section-6 defines: SYSLOG-MSG = HEADER SP STRUCTURED-DATA [SP MSG] neither STRUCTURED-DATA nor MSG tell me how these fields end. Especially MSG is defined as as MSG-ANY / MSG-UTF8 which expands to virtually anything. There's nothing that says a newline marks the end (or an 8 or an a for that matter). Given the example messages (section 6.5): This is one valid message, or 2 valid messages depending on wether you say that a HEADER element must never occur in any MSG element: literal whitespace <34>1 2003-10-11T22:14:15.003Z mymachine.example.com su - ID47 - <34>1 2003-10-11T22:14:15.003Z mymachine.example.com su - ID47 | is this an end marker? \t stands for a tab <34>1 2003-10-11T22:14:15.003Z mymachine.example.com su - ID47 -\t<34>1 2003-10-11T22:14:15.003Z mymachine.example.com su - ID47 | is this an end marker? \n stands for a newline <34>1 2003-10-11T22:14:15.003Z mymachine.example.com su - ID47 -\n<34>1 2003-10-11T22:14:15.003Z mymachine.example.com su - ID47 | is this an end marker? Either I'm misreading the RFC or there just isn't any mention. The sizes specified in the RFC just say what the minimum length is expected that I can work with...

  Read the article

• No partition on USB Flash Drive?

  - by Skytunnel

  A friend gave me a corrupted USB memory stick to try recovery data from. But I've had some unusual results, so thought I'd share to see if anyone is familiar with this problem... First off I just tried opening from my own PC. Windows prompted to Format the drive, which I of course declined Downloaded TestDisk to anaylsis the drive. And right away I noticed something strange, on the listed drives it comes up as Disk /dev/sdc - 6144 B - USB Flash Drive That's right, the first USB flash drive smaller than a floppy disk!? Moving on anyway... first anaylsis comes up with: Partition sector doesn't have the endmark 0xAA55 TestDisk's Quick Search gave no results, moved on to Deeper Search: No partition found or selected for recovery This left me stumped. I tired a couple of other programs with no success I did manage to get a backup image, but it was just as small as TestDisk indicated, so nothing of use on it After a few hours trying various suggestions from other sources, I gave in and just tried formatting the drive. But returned the message: Windows was unable to complete the format. From googling that, the suggestion was to delete the partition. But there is no partition to delete in this case. most recently I've tried formatting from cmd, and got this result: Format D: /FS:FAT32 The type of the file system is RAW The new file system is FAT32 Verifying 0M 11 bad sectors were encountered during the format. These sectors cannot be guaranteed to have been cleaned The volume is too small for FAT32 Anyone got any suggestions? UPDATE: As per suggestion from @Karen, I tried running a CLEAN from DISKPART, results as follows DiskPart has encountered an error: The request could not be preformed because of an I/O device error.

  Read the article

• How to setup bindings for development IIS 7.5 with lot of sites

  - by Antonio Bakula

  I am a programmer in a small ASP.NET shop with very little expirience in server administration, and I have to setup IIS 7.5 to host lot of sites on newly installed windows server 2008 R2, these sites are test "clones" for sites on "real" web server and they should be accessible only in local network (domain). Developers should add new sites for our new customers. Project managers use this server to check progress and test new sites and new features, QA people have to have access to this site and test before we copy it to the "real" web server. Developers only have access to IIS console, in fact they can use RDP to test server with their developer domain credentials and permissions, also developers are local admins on that machine (tester). On our previous server I used different port numbers for each site. That worked but don't like this solution, I would prefer to use subdomains. But here are the problems: manually adding DNS records is not an option because we do not wont that developers have to administer domain DNS server, and currently this had to be done with domain administrator credentials. Is there a some way to add DNS record automatically ? I tried to add DNS record for subdomains on test server with wildcard (*.tester) and that seems to work for some time but that change coused some bad problems in our domain network and admin forbid me to mess with DNS, he said that I have to add DNS record for every subdomain manually and that I can not use wildcards, and there is nothing that I can do about it, mainly for "politicall" reasons :( obviously our admin is pretty much uncooperative, outsorced from different organization and I can't do anything about that. can I add another DNS server on that machine ? What must be setup on clients machines to "tell" them to use domain DNS server and tester domain server ? So please I need someone to give me some advice, what should I do ? Is different port numbers only option left ? Thanks !

  Read the article

• Possible for linux bridge to intercept traffic?

  - by A G

  I have a linux machine setup as a bridge between a client and a server; brctl addbr0 brctl addif br0 eth1 brctl addif br0 eth2 ifconfig eth1 0.0.0.0 ifconfig eth2 0.0.0.0 ip link set br0 up I also have an application listening on port 8080 of this machine. Is it possible to have traffic destined for port 80 to be passed to my application? I have done some research and it looks like it could be done using ebtables and iptables. Here is the rest of my setup: //set the ebtables to pass this traffic up to ip for processing; DROP on the broute table should do this ebtables -t broute -A BROUTING -p ipv4 --ip-proto tcp --ip-dport 80 -j redirect --redirect-target DROP //set iptables to forward this traffic to my app listening on port 8080 iptables -t mangle -A PREROUTING -p tcp --dport 80 -j TPROXY --on-port 8080 --tproxy-mark 1/1 iptables -t mangle -A PREROUTING -p tcp -j MARK --set-mark 1/1 //once the flows are marked, have them delivered locally via loopback interface ip rule add fwmark 1/1 table 1 ip route add local 0.0.0.0/0 dev lo table 1 //enable ip packet forwarding echo 1 > /proc/sys/net/ipv4/ip_forward However nothing is coming into my application. Am I missing anything? My understanding is that the target DROP on the broute BROUTING chain will push it up to be processed by iptables. Secondly, are there any other alternatives I should investigate? Edit: IPtables gets it at nat PREROUTING, but it looks like it drops after that; the INPUT chain (in either mangle or filter) doesn't see the packet.

  Read the article

• Updating ASUS BIOS on Windows 7 64bit

  - by joesavage

  I've recently decided that I want to try and utilize my two graphics cards so that I can have a dual monitor setup. Unfortunately Windows only seems to notice my most recent graphics card installation - and so I've been told that I should look into my BIOS and try to enable two graphics cards. I could not find this setting anywhere in my M2N68-AM Plus v0210 BIOS. After some further research I figured that I should perhaps upgrade my BIOS, so I searched and managed to download the latest version (v1804) as a ROM file. However I am having difficulty figuring out how to install it. I've tried using the Asus EZFlash feature built into my BIOS, but when trying to load up a variety of different ROMs that are for my motherboard/BIOS I get the error: Boot block in file is not valid! I'm not totally sure what I should do to fix this, so I'm looking into other methods of upgrading my BIOS - however I can't really find any solutions that seem to work. Asus Update is for 32-bit only, AFUDOS doesn't appear to work on my Windows 7 64-bit system (I think it's supposed to run in DOS or something - but that just sounds confusing since I know nothing about DOS). Could anybody help me with this?

  Read the article

• Chrome will not load a web page with an <embed> element

  - by rossmcm

  I have been trying to get a simple sound web page going: Sound.html <script> function PlaySound () { var sounder = document.getElementById ("ToneA") ; sounder.Play () ; } </script> <embed id="ToneA" height="1" width="1" src="https://dl.dropboxusercontent.com/u/311035/ToneA.mp3" autostart="false" enablejavascript="true"//> <button onclick="PlaySound () ;">Play</button> The test web page is here. It plays in IE, but not in Firefox or Chrome. My problem: Chrome reports "Could not load VLC Plugin". It seems to be a known problem that the VLC community don't necessarily feel like fixing at the moment, and is a result of Google choosing not to allow some certain kind of plugin. If I disable the plugin I no longer get the message but nothing happens when I click the button. Looking at the console in a debug window I see Uncaught TypeError: undefined is not a function Sound.html:7 PlaySound Sound.html:7 onclick which suggests Chrome could not find anything else to handle the sound file. How to I tell Chrome to use (e.g.) Windows Media Player? * UPDATE * This is apparently because the VLC plugin is a NPAPI plugin and Chrome no longer supports these. I have uninstalled VLC and this has removed the error on loading the webpage with an embedded sound element, but it still doesn't invoke WMP instead.

  Read the article

• Embedded Windows XP

  - by Kyle

  My company acquired a brake press for bending large structural steel plates. We received it second hand and it came with an embedded copy of windows XP. Now for the part that's driving me nuts: plug and play has been turned off, also accessibility options has been disabled. What does this mean for me? Keyboards will not work! Nothing that plugs into a USB port will work and it does not have a CD ROM drive. I have tried to turn on plug and play using the on screen keyboard but it is not there since accessibility options is turned off. I would just get an updated copy of the the embedded OS but they come from Sweden and are extremely expensive. I assume there has got to be a way to get a USB devices to work. We need to get a wifi adapter on it so I can use team viewer and remotely configure it for our needs. Things to keep in mind: There is no keyboard so everything has to be done with the mouse There is no PS2 port for a keyboard just a mouse. Odd. I am 5 states away from this location and have been working with a tech who is physically installing the machine. System 32 seems to be missing A LOT of files, the tech told me there is only 8 folders in there and no other files (I don't even understand how Windows is running like this). If anyone has ANY ideas I would appreciate it, I am unsure where to go from here.

  Read the article

• Windows Server 2008 is stuck at "configuring updates - stage 3 of 3 - 0% complete"

  - by Chris

  This has happened the last two times I've done updates to this system, and I really have no idea what is going on. It is installing a only a month's worth of updates. It only responds to ping and no services are up, so I can't view the system remotely (I have to hook up a monitor to see this message). In the past I've just restarted the system at this point and it eventually finishes updating. I want to know what I can do to avoid this situation, how to diagnose what is going on, and how to get any kind of remote access during the updates. Edit: I can start the machine in safe mode (where I did nothing but backup some files). I restarted and it no longer tries to do a windows update, just goes to the desktop where everything seems extremely broken. I can click on some things, but not launch most programs. I guess all I can do at this point is do a system restore or something. Edit: Re-installed windows on this system yesterday. That's my usual solution to issues I don't feel like diagnosing, like this one.

  Read the article

• How do I connect remotely to SQL Server from Windows client?

  - by humble_coder

  Hi All, Having a bit of an issue connecting to SQL SERVER remotely from Windows. I've verified that all of my settings are correct via SQL SERVER MANAGEMENT STUDIO EXPRESS and SQL SERVER CONFIGURATION MANAGER. I can connect remotely using ODBC drivers from other OSes (e.g. OS X, Linux, etc). However, when I connect with the same credentials from a remote Windows machine using "SQL SERVER" as the driver I am told that the system cannot connect. I've tried creating an ODBC Data Source and I get the same error: Connection failed: SQLState: '01000' SQL Server Error: 14 [Microsoft][ODBC SQL Server Driver][TCP/IP Sockets]ConnectionOpen(InvalidInstance()). Connection failed: SQLState: '08001' SQL Server Error: 14 [Microsoft][ODBC SQL Server Driver][TCP/IP Sockets]Invalid Connection From the non-windows machines I can use the IP address of the SQL Server just fine. However, on the remote Windows machine, neither IP address nor named instance works. FYI, I can create an ODBC Data Source using the named instance on the machine actually running the SQL Server (but this is, of course, nothing special -- just proof that it isn't completely hosed). One interesting note: If I use SQL STUDIO 2005 from a Windows client machine, I can use the IP address to connect remotely. Still, the whole reason I bring this up is because I need to use a software package I've written to connect to SQL Server remotely from Windows machines as well. Previously the solution was only needed to xfer data from SQL Server into a PostGRES or MySQL database on non-Windows machines (due to DBA preference). However, now they also want to move the data from the legacy software to MySQL even on Windows. Any assistance would be most appreciated. Feel free to provide a full example connection string. Best

  Read the article

• Windows 7 scheduled task returns 0x2

  - by demmith

  I have identical scheduled tasks running in Windows XP Pro and Windows 7. The XP Pro one runs fine, the Windows 7 one always returns 0x2 (which means, "The system cannot find the file specified"; however, executing from the command line is no problem) in the Last Run Result column of the Task Scheduler UI. The scheduled task executes a .bat file daily. The .bat file contains a call to execute a Perl script. As I stated in the previous paragraph, it executes under XP without any trouble but under Windows 7, no dice. The task under Windows 7 is set to "run whether the user is logged on or not." In this case it is me, I am the only user of the system. It is also set to "Run with highest privileges." And it is not hidden. The .bat file executes perfectly well from the command line - it calls the Perl script as expected and the Perl script does its thing. I have searched far and wide looking for an appropriate answer to this issue. So far I have found nothing. What the devil is going on with this Win7 scheduled task? I am ready to pull my hair out.

  Read the article

• Isn't a hidden volume used when encrypting a drive with TrueCrypt detectable?

  - by neurolysis

  I don't purport to be an expert on encryption (or even TrueCrypt specifically), but I have used TrueCrypt for a number of years and have found it to be nothing short of invaluable for securing data. As relatively well known free, open-source software, I would have thought that TrueCrypt would not have fundamental flaws in the way it operates, but unless I'm reading it wrong, it has one in the area of hidden volume encryption. There is some documentation regarding encryption with a hidden volume here. The statement that concerns me is this (emphasis mine): TrueCrypt first attempts to decrypt the standard volume header using the entered password. If it fails, it loads the area of the volume where a hidden volume header can be stored (i.e. bytes 65536–131071, which contain solely random data when there is no hidden volume within the volume) to RAM and attempts to decrypt it using the entered password. Note that hidden volume headers cannot be identified, as they appear to consist entirely of random data. Whilst the hidden headers supposedly "cannot be identified", is it not possible to, on encountering an encrypted volume encrypted using TrueCrypt, determine at which offset the header was successfully decrypted, and from that determine if you have decrypted the header for a standard volume or a hidden volume? That seems like a fundamental flaw in the header decryption implementation, if I'm reading this right -- or am I reading it wrong?

  Read the article

• Windows Search not searching in files

  - by Cylindric

  I am trying to get Windows Search to work on my Windows Server 2008 SP2 fileserver, so I can search in files for content. I have added the Windows Search Service role to the server, and using the right-click properties in Explorer set some folders to "Index this location". The problem is that neither on the server or remotely can I search in the files. I seem to get some inconsistencies in the GUIs, for example the "Indexing Options" panel shows me just 6 locations indexed, but if I click "Modify" I see nearly everything ticked. For example, the "SeachTest" folder under "infrastructure" has the "index this location" option ticked, but the "Projects" folder does not. I assume this is why some are grey and some not, but they are all ticked. T The "SearchTest" folder contains some files that have nothing but the text PurpleOrange in it, so I should be able to find those. So, to summarise: Which locations are indexed? The ones in the "Index these locations" list, the ones ticked, or the ones not greyed-out in the list? How do I get to the state where I can click in the search box and type PurpleOrange and see the files?

  Read the article

• Hibernation fails; The system cannot find the file specified

  - by GMMan

  Recently I installed Ubuntu 12.04.1 LTS on my Lenovo Y480. Hibernation was working properly after the Ubuntu install, but I was making sure all of the operating systems on my system worked, including OneKey Recovery (recovery partition). It is of note that I installed Windows 7 from scratch with a disk image I downloaded off of my university's DreamSpark program, and further to that I had to image the partition with Paragon Backup & Recovery, repartition to convert the Windows partition to extended, install Ubuntu, and then restore the image. During that process I also used the Windows disc to edit the BCD as to reuse the existing entry for the restored partition. I also used the automated "repair your computer" option. With verification, I noticed that the "repair your computer" option actually wrote to the wrong BCD (the recovery partition), and I mounted the partition and restored the original BCD (from a copy I made earlier), and rebooted. At this point my GRUB broke, and I was able to restore it. At this point hibernation broke. I tried powercfg /h off and powercfg /h on, rebooted, and nothing. Also tried increasing the hibernation file size as directed on this post, but it still doesn't work. Executing shutdown /h yields The system cannot find the file specified.(2). What file? It seems that mounting the system partition sometimes works, but I don't want to keep it mounted in case it gets written to accidentally. How do I permanently fix this?

  Read the article

< Previous Page | 462 463 464 465 466 467 468 469 470 471 472 473  | Next Page >