Search Results

Search found 24387 results on 976 pages for 'ssh client'.

Page 468/976 | < Previous Page | 464 465 466 467 468 469 470 471 472 473 474 475  | Next Page >

• Boinc permissions problem on OS X

  - by Erik Vold

  I installed boinc 6.10.21 on my OS X 10.5 in order to upgrade from a 6.6 version that I was running today, and I am the admin user, and I was logged in as the admin user. As I was installing 6.10.21 I was asked if non admin users should be allowed to use Boinc, and I said 'yes' to this. Then when I tried to open Boinc I got a message like the following: "You currently are not authorized to manage the client. Either re-install and allow non-admin users or contact your administrator to add you to the 'boinc_master' user group." So I tried to reinstall first, and I was not asked if non admin users should be allowed to use Boinc.. so I retried a few times and got no different result.. So I downloaded 6.10.43 and installed that, and again I was not asked if non admin users should be allowed to use boinc.. and when I tried to run Boinc I got the same message like: "You currently are not authorized to manage the client. Either re-install and allow non-admin users or contact your administrator to add you to the 'boinc_master' user group." So I did a Google search trying to figure out how to add my admin user to the bonic_master user group and found this which suggested I run the following in terminal: "sudo dscl . -append /Groups/boinc_master GroupMembership <your user's short name> CR" So I did this and now I get the following error: BOINC ownership or permissions are not set properly; please reinstall BOINC (Error code -1200) So I reinstall and I am ever asked the question about allowing non admin users again, and I still get this error message every after every reinstall attempt.. What should I do?..

  Read the article

• lxc bandwidth control using tc

  - by kumar

  I am trying to restrict bandwidth inside my containers. I have tried using the following commands , But I think it is not getting effective. cd /sys/fs/cgroup/net_cls/ echo 0x1001 > A/net_cls.classid # 10:1 echo 0x1002 > B/net_cls.classid # 10:2 tc qdisc add dev eth0 root \ handle 10: htb tc class add dev eth0 parent 10: \ classid 10:1 htb rate 40mbit tc class add dev eth0 parent 10: \ classid 10:2 htb rate 30mbit tc filter add dev eth0 parent 10: \ protocol ip prio 10 \ handle 1: cgroup Here A and B are containers created with this command. lxc-execute -n A -f configfile /bin/bash lxc-execute -n B -f configfile /bin/bash Whereas configfile contains only this entry: lxc.utsname = test_lxc AFter starting the container , I have started vsftpd inside container A and try to access the files using the ftp client from another machine. Then I killed vsftpd in container A and started vsftpd in container B and try to access the files using ftp client from another machine. I cannot observe any difference in performance, for that matter it is nowhere nearer to 40mbit/30mbit. Please correct me whether anything wrong here.

  Read the article

• Thunderbird alerts when expected email does not arrive

  - by user871199

  I am on Ubuntu 12.04 using Thunderbird as email client. Both are up to date in terms of updates. I have bunch of nightly jobs that do the work and send a status mail. It gets tedious if you keep getting same/similar mails every day so I ended up writing a mail filter rule which causes emails to end up in their respective folders automatically. If things are going ok, I really don't need to read emails. Failure emails are sent to different alias - if the job runs. We recently discovered that one of the job had not run for few days as someone accidentally disabled it. In order to avoid such problems in future, I would like to setup thunderbird in such a way that if I don't get email from given address within given duration, it should alert me. My dream solution is to set up frequency - some jobs do run every 4 hours. Is this possible? Can I setup Thunderbird (preferred) or other email client for reminding me when expected email does not show up. Based on comments and answer I received, here are the reasons why I would like to use Thunderbird. We are already using Thunderbird. It has calender support via plugin, so I suppose someone is already watching time to remind us about the event. May be this another type of event. Additional job is one more failure point, may complicate life if it has to monitor multiple hosts. Additional tools - same thing, one more failure point. Thunderbird can be run across all the platforms we are using - Windows and Ubuntu. It sort of becomes platform independent solution.

  Read the article

• SQL Server 2005 SP3 on Windows 7 - No Management Studio

  - by Mike Thomas

  I've been trying for a day and a half now to get SQL Server 2005, DEV edition, to work on Windows 7, 64 bit prof. I install from the disk, then run SP 3. I get a failure on the Client Components section of the Installation Progress along with this vague message - Product : Client Components Product Version (Previous): 1399 Product Version (Final) : Status : Failure Log File : C:\Program Files\Microsoft SQL Server\90\Setup Bootstrap\LOG\Hotfix\SQLTools9_Hotfix_KB955706_sqlrun_tools.msp.log Error Number : 1712 Error Description : MSP Error: 1712 One or more of the files required to restore your computer to its previous state could not be found. Restoration will not be possible. I've uninstalled all Visual Studio and tried to make this as clean as possible, and have read a lot of the blog posts, but am really at my wits end about this. I am not a DBA, but I use SQL Server all the time when coding and testing apps. Does anyone have any ideas as to where I can get this sorted out? I've been ati this for a long time and have never encountered an installation as bad as this one. Thanks Mike Thomas

  Read the article

• NIS user not being added to NIS group

  - by Brian

  I have set up a NIS server and several NIS clients. I have a user and a group on the NIS server like so: /etc/passwd: myself:x:5000:5000:,,,:/home/myself:/bin/bash /etc/group: fishy:x:3001:otheruser,etc,myself,moreppl I imported the users and groups on the NIS client by adding +:::::: to /etc/passwd and +::: to /etc/group. I can log in to the NIS client, but when I run groups, fishy is not listed. But getent group fishy shows that it was imported correctly and lists me as a member. And if I do sudo su - myself, then suddenly groups says I am in the group! I also had nscd installed, and the groups worked correctly for a while. It seemed like after being logged in for a while, I would silently be dropped out of the group. If I restarted nscd and logged in again, then the groups worked correctly...for a while. There are no UID or GID conflicts with local users or groups. Update: Contents of /etc/nsswitch.conf: passwd: compat group: compat shadow: compat hosts: files nis dns networks: files protocols: db files services: db files ethers: db files rpc: db files netgroup: nis aliases: nis files

  Read the article

• VPN Error 691 but server says authenticated on server

  - by Andy

  Hello all, I have a problem with a vpn connection on Windows XP SP3 that appears to be related to an account (maybe privilleges or an option that I have missed). When connecting using my account, which is a domain administrator account it will connect to through the vpn fine. However, using an account created for another person they receive Error 691: Username or Password is not valid for this domain. On the domain controller (windows 2003) I see a logon successful message: User DOMAIN\user was granted access. Fully-Qualified-User-Name = int.company.net.au/People/Management/User NAS-IP-Address = 10.30.0.3 NAS-Identifier = not present Client-Friendly-Name = MelbourneCore Client-IP-Address = Router-ip Calling-Station-Identifier = not present NAS-Port-Type = Virtual NAS-Port = 77 Proxy-Policy-Name = Use Windows authentication for all users Authentication-Provider = Windows Authentication-Server = undetermined Policy-Name = Remote VPN Access Authentication-Type = MS-CHAPv1 EAP-Type = Does anyone have any ideas as to where else I should look for finding a solution? If i use the wrong password it gives a logon failure error in the event viewer. Also removing them from the remote access group gives a logon failure error. Nothing appears in the event viewer on the local machine. In the past all that is required is to add them into our Remote Access Users group. Any help?

  Read the article

• Web hosting for multiple web sites providing system isolation

  - by Justin

  We have a small number of projects where we expect the client will not be maintaining the installed versions of applications we install to power the site (such as Drupal). Given that an important part of security is keeping things updated, we don't want to host these projects on our Plesk-powered dedicated servers that currently host lots of our other client's websites. Our goal is to find a host where we can deploy isolated instances (be these slices, virtual servers, grid servers, etc) for each individual (or groups of 2-3) web sites as we need them. These instances would be completely separate, so that if one web site were hacked it would not impact any other site. Typical hosting requirements: Linux Apache PHP 5 MySQL Supports Drupal Ability to setup a cron task (but we don't need SSH access) Daily backups Virtualized/cloud hosting (we want to avoid shared) Pricing per site is around $25/month OS is patched automatically Some options we have considered but won't work: MediaTemple: Two major data center-wide security incidents and recent downtime foster doubt about this host's technical ability. Slicehost: This would require us to manage the entire server, which we don't want to do. Rackspace Cloud Sites (formerly Mosso): No backup options. Do you have any recommended hosting options for given these requirements?

  Read the article

• High latency issue for web service call from amazon aws ec2 to local server

  - by SibzTer

  We have a legacy web application that is running in our data center on premises located in Houston. We have a developed a new .net 4 based web application in order to provide new features to customers. The new web application is hosted in amazon aws ec2 environment (N. Virginia region us-east-1b zone). In order to get seamlessly integrate with the legacy application the new web application makes web service calls to retrieve data. We are seeing an unusually high latency time in the order of 5+ seconds for these web service calls. The exact same web service call returns in less than a second on our local PCs (which makes sense given physical proximity to the actual server). The weird part is that we have developers in California who also have the same milliseconds response time. We are testing the web service response using third party tools such as SoapUI, Google Chrome extensions such as Advanced REST Client, Postman REST Client, etc. As if this wasnt weird enough, we have noticed the same low latency from certain other ec2 instances while testing which are in the same region and availability zone as well. If we experienced the high latency consistently from all the ec2 instances I could understand. But there is something else going on. Comparing the various stats and results between the low latency and high latency ec2 servers do not show any significant differences: ping (constant 40ms), tracert, winmtr, etc. We have instances that are in the VPC as well. So I tried both the public and private IP address of the web service host server and that didnt make a difference either for the above results. We need to resolve this latency issue as this is causing the resulting web pages to load very slowly (almost 15+ seconds which is simply unacceptable). The ec2 instances have Windows Server Datacenter 64 bit. Let me know if there is any other infor I can provide to help diagnose this.

  Read the article

• How to configure VirtualBox server for performance at home

  - by BluJai

  I currently have two physical Ubuntu Server 10.10 servers at home: one serves as our firewall/router/DHCP/VPN server and the other performs double-duty as a file server and a VirtualBox host for an Ubuntu Desktop 10.10 machine which I use from remote connections (via NoMachine) for many thin-client purposes which are irrelevant to my question. What I'd like to accomplish is to consolidate the two physical machines into one which is a dedicated VirtualBox host (most likely running Ubuntu Server 10.10). Note that I'd like to stick with VirtualBox (if possible) because I'm most comfortable with it and use it on a daily basis at both home and work. Specifically, I plan to have one VM set up as file server, another as the firewall/router/DHCP/VPN (or possibly split those a bit) and a third, which is the only current VM (already VirtualBox), which is the thin-client host. My question comes down to performance and/or recommendations about the file server VM. The file server hosts about 6 terabytes of data across 4 drives. What I'd like to do is use raw disk access from the VM directly to the existing disks. However, I'm curious what performance advantage/disadvantage that would have as compared to using shared folders from the VM host and basically just have the whole drive served as a shared folder to the VM which would then serve it to the other machines on the network. I don't know if virtual disks would even work in this scenario and I certainly wouldn't want a drive to be filled with just a single file which is 1.5 TB (disk image). To add understanding of context, but not to get additional advice, I want to virtualize these machines because I intend to regularly use the snapshot capabilities of VirtualBox for the system disks (which will be virtual drives) of the VMs and I have some physical space/power needs to address (as I mentioned, this is at home).

  Read the article

• tcp connect hangs on SYN_SENT if something listens, gets CONN_REFUSED if nothing listens

  - by Amos Shapira

  I'm hitting a very strange problem - when I try to connect to one of our servers the client hangs with SYN_SENT if something listens on the port (e.g. Apache on port 80, sshd on port 22 or SMTP on port 25) but if I try to connect to a port on which nothing listens then I immediately get a "CONNECTION refused" error. Connecting to other applications (e.g. rsyncd on some arbitrary port) succeeds. I ran tcpdump on the server and see that the SYN packets arrive to it but it only sends a response if nothing listens on that port. e.g.: on the server I run: # tcpdump -nn port 81 06:49:34.641080 IP 10.x.y.z.49829 server.81: S 3966400723:3966400723(0) win 12320 06:49:34.641118 IP server.81 x.y.z.49829: R 0:0(0) ack 3966400724 win 0 But if I listen on this port, e.g. with nc -4lvvv 81 & Then the output of tcpdump is: 06:44:31.063614 IP x.y.z.45954 server.81: S 3493682313:3493682313(0) win 12320 (and repeats until I stop it) The server is CentOS 5, the client is Ubuntu 11.04, the connection is done between two LAN's over per-user TCP OpenVPN. Connection to other servers on that network do not have a problem. Connecting from the other servers on the same network to that server works fine. Connections from other clients in our office over openvpn is also not a problem. What am I missing? Thanks.

  Read the article

• Server 2008 NAT Internet Not Working

  - by Jack

  I'm trying to set up Routing and Remote Access on Windows Server 2008 R2, I have a network connection that I want to share the internet from to another private network. The server has two NICs which are configured as follows: External NIC (Dynamically assigned by ISP) IP:10.175.4.150 Subnet:255.255.192.0 Gateway:10.175.0.1 DNS:10.175.0.1 Internal NIC IP:172.16.254.1 Subnet:255.255.255.0 Gateway:None DNS:None I have set the external NIC to be the public interface and enabled NAT on it in the RRAS MMC and set the internal NIC to be a private interface. I have also set up the DNS forwarding or whatever it is in the NAT section. From a client (IP:172.16.254.2) I can ping the server and access files on it, when I try to browse the web with the default gateway set to the internal NIC ip I end up getting a 404 page which is returned from the ISPs default gateway. I'm guessing it's something to do with the double NAT possibly. Trying to ping the ISPs default gateway from a private network client just times out as does accessing it directly. I've disabled and reconfigured RRAS multiple times and that doesn't seem to have made a difference, so can anyone tell me what I'm doing wrong? Thanks.

  Read the article

• Windows XP laptop doesn't appear in WSUS All computers list

  - by George

  I have this one laptop that doesn't appear in WSUS all computers list. We have about 23-25 PCs/laptops/servers in the network, all, but one are listed in WSUS. This is what I have done so far: 1) Changing Updates on local PC: Go to your Windows XP client and start a new Microsoft Management Console (MMC). At Start, Run, type MMC. Use Ctrl+M to add a new snap-in. Click Add, and then add the Group Policy Object Editor for the Local Computer. Click Close, and then click OK. Expand the Local Computer Policy. Under Computer Configuration, go to Administrative Templates, Windows Components, Windows Update. In the right-hand pane, double-click Specify intranet Microsoft update service location. Configure the settings to reflect my WSUS server. Click OK and then close the MMC without saving it. executed wuauclt.exe /detectnow 2) Edited registry key to be pushed to the PCs using GPO [HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\WindowsUpdate] "WUServer"=http://wsusserver "TargetGroupEnabled"=dword:00000001 "TargetGroup"="WINXP" "WUStatusServer"=http://wsuswerver 3) executed wuauclt /resetauthorization /detectnow 4)Synchronised and refreshed the group I am running out of ideas here. The client is running Windows XP pro, WSUS version is 3.0 and is running on Windows 2008 R2 64-bit. Please, help! Thanks! EDIT 13.IX.2012 @ 15.40 I should have also mentioned that we do have a Windows Update GPO for workstations group and that laptop is a part of that group.

  Read the article

• How to configure VirtualBox server for performance at home

  - by BluJai

  I currently have two physical Ubuntu Server 10.10 servers at home: one serves as our firewall/router/DHCP/VPN server and the other performs double-duty as a file server and a VirtualBox host for an Ubuntu Desktop 10.10 machine which I use from remote connections (via NoMachine) for many thin-client purposes which are irrelevant to my question. What I'd like to accomplish is to consolidate the two physical machines into one which is a dedicated VirtualBox host (most likely running Ubuntu Server 10.10). Note that I'd like to stick with VirtualBox (if possible) because I'm most comfortable with it and use it on a daily basis at both home and work. Specifically, I plan to have one VM set up as file server, another as the firewall/router/DHCP/VPN (or possibly split those a bit) and a third, which is the only current VM (already VirtualBox), which is the thin-client host. My question comes down to performance and/or recommendations about the file server VM. The file server hosts about 6 terabytes of data across 4 drives. What I'd like to do is use raw disk access from the VM directly to the existing disks. However, I'm curious what performance advantage/disadvantage that would have as compared to using shared folders from the VM host and basically just have the whole drive served as a shared folder to the VM which would then serve it to the other machines on the network. I don't know if virtual disks would even work in this scenario and I certainly wouldn't want a drive to be filled with just a single file which is 1.5 TB (disk image). To add understanding of context, but not to get additional advice, I want to virtualize these machines because I intend to regularly use the snapshot capabilities of VirtualBox for the system disks (which will be virtual drives) of the VMs and I have some physical space/power needs to address (as I mentioned, this is at home).

  Read the article

• Postfix Problem (helo/hostname mismatch)!

  - by CuSS

  Hi all, I have a server, and it is running a error for one email only (all other mails in that domain are working). How can i fix it? (The error is above:) May 17 11:43:56 webserver postfix/policyd-weight[5596]: weighted check: IN_DYN_PBL_SPAMHAUS=3.25 NOT_IN_SBL_XBL_SPAMHAUS=-1.5 NOT_IN_SPAMCOP=-1.5 NOT_IN_BL_NJABL=-1.5 DSBL_ORG=ERR(0) CL_IP_NE_HELO=4.75 RESOLVED_IP_IS_NOT_HELO=1.5 HELO_NUMERIC=10.625 (check from: .eticagest. - helo: .[10.0.0.17]. - helo-domain: .17].) FROM_NOT_FAILED_HELO(DOMAIN)=6.25; <client=188.80.139.211> <helo=[10.0.0.17]> <[email protected]> <[email protected]>; rate: 21.875 May 17 11:43:56 webserver postfix/policyd-weight[5596]: decided action=550 Mail appeared to be SPAM or forged. Ask your Mail/DNS-Administrator to correct HELO and DNS MX settings or to get removed from DNSBLs; MTA helo: [10.0.0.17], MTA hostname: bl15-139-211.dsl.telepac.pt[188.80.139.211] (helo/hostname mismatch); <client=188.80.139.211> <helo=[10.0.0.17]> <[email protected]> <[email protected]>; delay: 6s

  Read the article

• Outlook Shared Address book and contact not displaying

  - by user224061

  We have a shared Exchange addressbook with distribution email groups. When someone connects to the shared addressbook, composes an email to a group, the email distribution list is empty, then the distribution list is expanded. In troubleshooting, I noticed that when we expand the distribution list to view the recipients, most of the recipients are missing and only semicolons appear. CLICK HERE FOR IMAGE Further troubleshooting, I notice that when I open the distribution list with my Outlook client and click on the Update Now icon, and then go to create the email then when I expand the group the email addresses now appear. CLICK HERE FOR IMAGE Now, my Outlook profile is a cached profile. The shared contact list that I pulled the distribution list from is an online/non-cached shared contact list. What I also found is that if I switched my Outlook client to be online only(not cached) the share address book lists appear properly when expanded. Is there any way to make this list appear correctly without having to click on update now for each and every distribution list in the shared contacts list we have on the server? I would really prefer that every time one wants to use this shared contact list, they do not have o click the update not button or switch from cached mode to make this work. T.I.A

  Read the article

• who has files open on a linux server

  - by Robert

  I have the fairly common task of finding who has files open on our Linux (Ubuntu ) file server in our Windows environment. We use Samba on the network and I use Putty from my workstation to establish a shell window to run bash scripts. I have been using something like this to find what files are open: (this returns a list of process ids with each open file) Robert:$ sudo lsof | grep "/srv/office/some/folder" Then, I follow up with something like this to show who owns the process: (this returns the name of the machine on the network using the IP4 protocol who owns the process) Robert:$ sudo lsof -p 27295 | grep "IPv4" Now I know the windows client who has a file open and can take action from there. As you can tell this is not difficult but time consuming. I would prefer to have a windows application I can run that would just give me what I want. So, I have been thinking about creating some process I can run on Linux that listens on a port and then returns a clean list of all open files with the IP address of the host who has the file open. Then, a small windows client application that can send the request on the port. It seems like this should be a very common need but I can not find anything like this that has been done before. Any suggestions?

  Read the article

• Hardware, network infrastructure for runnng gaming server nd on VirtualGL

  - by archer

  Foud nice project VirtualGL (http://www.virtualgl.org/). Tried to run 3D fames (EVE Online, Prototype) on server and display the output on thin client using 100Mbps network. Server: Gentoo Linux on AMD Phoenom II x6 3.4Gz, 8GB RAM, 2x NVIDIA 9800 GTX in single session with display resulution 1024x768 on client. Performance is very promising. Going to increase network speed to 1Gbps (using either Ethernet or Fiber) and run 5-6 clients simultenously. My questions are: a) what would be better for network - 1Gbps Ethernet or Fiber (clients are distributed in max 20m around server)? Is that a must to use managed switch for better network performance? b) Should I increase number of video cards to put in SLI on server (going to use Gigabyte GA-890FXA-UD7 which has 6 PCIExpress slots [2 x4, 2 x8 and 2 x16]). Will it impact performance significantly. If I need to increase the number of video cards - what would be better - put 2 banks of video cards with 3 in bank using SLI, or 3 banks with 2 in the bank? Would linux recognize that and properly use all banks of video cards? c) any suggestions on good thin clients supporting 1920x1080 HDMI video and 1Gbps network I understand that my questions can't be answered clearly (unless someone already managed to use this kind of stuff ;)) although any suggestions would be very helpful.

  Read the article

• can't install mysql-devel on centos 6.5

  - by Latheesan Kanes

  I need mysql-devel package to be installed on my CentOS 6.5 running Percona 5.5 (already installed & running). When I try to install the devel package like this: yum --enablerepo=remi install mysql-devel I get the following error: Error: Package: mysql-devel-5.5.37-1.el6.remi.i686 (remi) Requires: real-mysql-libs(x86-32) = 5.5.37-1.el6.remi Available: mysql-libs-5.5.36-1.el6.remi.i686 (remi) real-mysql-libs(x86-32) = 5.5.36-1.el6.remi Available: mysql-libs-5.5.37-1.el6.remi.i686 (remi) real-mysql-libs(x86-32) = 5.5.37-1.el6.remi Error: Package: mysql-5.5.37-1.el6.remi.i686 (remi) Requires: real-mysql-libs(x86-32) = 5.5.37-1.el6.remi Available: mysql-libs-5.5.36-1.el6.remi.i686 (remi) real-mysql-libs(x86-32) = 5.5.36-1.el6.remi Available: mysql-libs-5.5.37-1.el6.remi.i686 (remi) real-mysql-libs(x86-32) = 5.5.37-1.el6.remi Error: mysql conflicts with Percona-Server-client-55-5.5.37-rel35.0.el6.i686 Here's what's currently installed on my server: [root@server1 ~]# yum list installed | grep mysql php-mysqlnd.i686 5.4.29-1.el6.remi @remi [root@server1 ~]# yum list installed | grep percona Percona-Server-client-55.i686 5.5.37-rel35.0.el6 @percona Percona-Server-server-55.i686 5.5.37-rel35.0.el6 @percona Percona-Server-shared-55.i686 5.5.37-rel35.0.el6 @percona [root@server1 ~]# Any ideas how to fix this dependency error?

  Read the article

• Problem with PXE boot

  - by user70523

  I followed the following link for PXE boot, http://www.howtoforge.com/setting-up-a-pxe-install-server-on-ubuntu-9.10-p3 and I was able to ping the client from the server and also when I booted up the client It is getting the IP address from the server. But later,I got this error PXELinux 3.82 2009-06-09 . . . [other informations] !PXE Entry point found (we hope) at 9D3B:0109 via plan A UNDI code segment at 9D3B len 16C2 UNDI data segment at 933B len A000 Getting cached packet 01 02 03 . . . [other informations] TFTP prefix: Trying to load: pxelinux.cfg/ec5db4c0-74fe-d511-b9e7-3d9235afe5a1 Trying to load: pxelinux.cfg/01-00-17-31-b6-5e-a8 Trying to load: pxelinux.cfg/0A64491E Trying to load: pxelinux.cfg/0A64491 Trying to load: pxelinux.cfg/0A6449 Trying to load: pxelinux.cfg/0A644 Trying to load: pxelinux.cfg/0A64 Trying to load: pxelinux.cfg/0A6 Trying to load: pxelinux.cfg/0A Trying to load: pxelinux.cfg/0 Trying to load: pxelinux.cfg/default Unable to locate configuration file Boot failed: press a key to retry or wait for reset I have put all the files mentioned in the link in tftpboot. Can anyone explain what could be the problem. Thanks in advance

  Read the article

• How to get gigabit network speeds on Windows XP?

  - by JB

  We've just installed gigabit switches at work, and things on the Linux side are going well. Our linux boxes, which use a Intel Corporation 82566DM-2 Gigabit nic (according to lspci), consistently get over 900 mbits/sec: iperf -c ipserver ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 16.0 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.40.9 port 39823 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.08 GBytes 929 Mbits/sec We have a bunch of Windows XP 64-bit machines that use Broadcom NetXtreme 57xx cards. I spent around a day trying to get equivalent speeds on them, but couldn't get above 200 Mbits/sec. I noticed the Windows iperf tests said that the TCP window size was 8 Kb by default (as opposed to 16 Kb on Linux, so I modified my test to reflect that. Still no love. I went to Broadcom's site, downloaded the latest drivers for the card and installed. Still no love. However, finally, I tried a 64 Kb window size with the new drivers, and finally an improvement! $ iperf -c ipserver -w64k ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 64.0 KByte ------------------------------------------------------------ [ 3] local 192.168.40.214 port 1848 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 933 MBytes 782 Mbits/sec Much better, but still not really taking advantage of the full capabilities of the network. If the Linux box can reach 950 Mbits/sec consistently, this box should be able to as well. Also, if you're wondering about the medium, this is over the same cable...I'm switching back and forth. Any suggestion or ideas would be really welcome. Thanks!

  Read the article

• Apache LDAP auth: denied all time

  - by Dmytro

  There is my config (httpd 2.4): <AuthnProviderAlias ldap zzzldap> LDAPReferrals Off AuthLDAPURL "ldaps://ldap.zzz.com:636/o=zzz.com?uid?sub?(objectClass=*)" AuthLDAPBindDN "uid=zzz,ou=Applications,o=zzz.com" AuthLDAPBindPassword "zzz" </AuthnProviderAlias> <Location /svn> DAV svn SVNParentPath /DATA/svn AuthType Basic AuthName "Subversion repositories" SSLRequireSSL AuthBasicProvider zzzldap <RequireAll> Require valid-user Require ldap-attribute employeeNumber=12345 Require ldap-group cn=yyy,ou=Groups,o=zzz.com </RequireAll> </Location> The Require valid-user is work. But ldap-attribite, ldap-filter, ldap-group does not work - denied in logs all time. I spent a lot of time but can't understand what's going on. This is the example of my logs: [Tue Sep 25 16:42:26.772006 2012] [authz_core:debug] [pid 23087:tid 139684003014400] mod_authz_core.c(802): [client 1.1.1.1:52624] AH01626: authorization result of Require valid-user : granted [Tue Sep 25 16:42:26.772014 2012] [authz_core:debug] [pid 23087:tid 139684003014400] mod_authz_core.c(802): [client 1.1.1.1:52624] AH01626: authorization result of Require ldap-attribute employeeNumber=12345: denied I checked all info with ldapsearch: there is a valid username, employee ID and other...

  Read the article

• Windows errors, how do I find root cause and fix it? Getting several errors

  - by Eric Martin

  My server is having issues and not responding to customer's https requests. I checked the event viewer and found several errors. These two are listed a couple of times: WINS encountered a database error. This may or may not be a serious error. WINS will try to recover from it. You can check the database error events under 'Application Log' category of the Event Viewer for the Exchange Component, ESENT, source to find out more details about database errors. If you continue to see a large number of these errors consistently over time (a span of few hours), you may want to restore the WINS database from a backup. The error number is in the second DWORD of the data section. And this one: An error occured while using SSL configuration for socket address 0.0.0.0:444. The error status code is contained within the returned data. SQL Server is not ready to accept new client connections. Wait a few minutes before trying again. If you have access to the error log, look for the informational message that indicates that SQL Server is ready before trying to connect again. [CLIENT: xxx.xxx.xxxx.xxx] I also found this in the event viewer but the computer has been restarted since this message and I have not seen it again. Configuring the Page file for crash dump failed. Make sure there is a page file on the boot partition and that is large enough to contain all physical memory. This is my virtual memory settings: I'm not familiar with WINS so I wasn't sure if that is where I start or how to resolve it. Is the WINS error causing the other problems or should I be looking somewhere else?

  Read the article

• apache with php fastcgi keeps going down

  - by Josh Nankin

  I have an apache2 server configured with MPM worker and php fast cgi. Lately the apache logs have been telling me that MaxClients is being reached frequently, even though it's already pretty high. My server is now constantly going down, and I see a bunch of lines like this in the log: [Sun Mar 06 04:25:40 2011] [error] [client 50.16.83.115] FastCGI: comm with (dynamic) server "/var/local/fcgi/php-cgi-wrapper.fcgi" aborted: (first read) idle timeout (20 sec) [Sun Mar 06 04:25:40 2011] [error] [client 50.16.83.115] FastCGI: incomplete headers (0 bytes) received from server "/var/local/fcgi/php-cgi-wrapper.fcgi" I can see that my php-cgi processes are pretty large (about 70mb on average). Here's my apache configuration for MPM worker: KeepAlive ON KeepAliveTimeout 2 <IfModule mpm_worker_module> StartServers 5 MinSpareThreads 10 MaxSpareThreads 10 ThreadLimit 64 ThreadsPerChild 10 MaxClients 20 MaxRequestsPerChild 2000 </IfModule> Heres my fastcgi apache configuration: <IfModule mod_fastcgi.c> # One shared PHP-managed fastcgi for all sites Alias /fcgi /var/local/fcgi # IMPORTANT: without this we get more than one instance # of our wrapper, which itself spawns 20 PHP processes, so # that would be Bad (tm) FastCgiConfig -idle-timeout 20 -maxClassProcesses 1 <Directory /var/local/fcgi> # Use the + so we don't clobber other options that # may be needed. You might want FollowSymLinks here Options +ExecCGI </Directory> AddType application/x-httpd-php5 .php AddHandler fastcgi-script .fcgi Action application/x-httpd-php5 /fcgi/php-cgi-wrapper.fcgi </IfModule> Here's my fastcgi wrapper: #!/bin/sh PHPRC="/etc/php5/apache2" export PHPRC PHP_FCGI_CHILDREN=8 export PHP_FCGI_CHILDREN exec /usr/bin/php-cgi Any help would be very very much appreciated!

  Read the article

• LDAP authentication issue with Kerio Connect

  - by djk

  Hi, We have Kerio Connect (mail server) running on a Windows Server 2003 server on a domain. In the webmail client, users are able to change their domain password. This functionality used to work fine until a user tried to change their password a few days ago, when every password they'd try would result in the webmail client claiming their password was "invalid". I spoke to Kerio about this and they claim that this error is returned by the domain controller, which supports my initial investigations. The error that the DC is logging when an attempt is made to change the password is this: "80090308: LdapErr: DSID-0C090334, comment: AcceptSecurityContext error, data 52e, vece" The "data 52e" part indicates that this is an "invalid credentials" error. I don't see how this can be as I've tried (in the Kerio Connect configuration) various accounts that have privileges to modify accounts, including my own as I am a domain admin. I have ran 'dcdiag' (all tests) on the DC and it came back passing every single one of them. I've searched high and low for an answer to this and came up empty. Does anyone have any idea why this may have suddenly started happening? Thanks! Edit: I should mention that the passwords we are changing to do comply with the complexity policy.

  Read the article

• How to set up a VPN Incoming connection with Windows to tunnel Internet traffic?

  - by Mehrdad

  I want to set up a VPN on a remote server to route all my Internet traffic for privacy reasons. I can set up an incoming connection and connect to it successfully. The problem is, I can just see the remote computer and no other Web sites will open. I want the remote server to act like a NAT. How can I do that? Note that I don't want to split Internet traffic. I actually want to send all the traffic to the remote server but need to make it relay the traffic. For the record, my remote server is Windows Web Server 2008 which does not have routing and remote access service. Clarification I'm mostly interested in server configuration. I don't have any problems configuring the client. By the way, Windows Web Server 2008 seems to have the same VPN features built in client OSes (like Vista) and specifically, it doesn't include the RRAS console in MMC. I'm also open to suggestions regarding third party PPTP/L2TP daemons available, if they are free.

  Read the article

< Previous Page | 464 465 466 467 468 469 470 471 472 473 474 475  | Next Page >