Search Results

Search found 19305 results on 773 pages for 'above the gods'.

Page 471/773 | < Previous Page | 467 468 469 470 471 472 473 474 475 476 477 478  | Next Page >

  • How do I troubleshoot a slow hard drive?

    - by Bruce Connor
    My computer is suffering of slow-downs and I'm not surprised (it's around 6 years old). Here's what I've verified: They are not very frequent (only a couple of times a day). When they happen a single application will hang for 10-60 seconds, while the rest don't hang but also get slow. Even as it is happening, the CPU usage stays low. It happens to applications (such as text editor, firefox, skype). It never happens to some applications (such as games) which I use for hours under heavy CPU load. Also of note: The Graphics card and PSU are new (around a year). Though I have a decent amount of software installed right now, this was happening even right after I reinstalled Windows. This HDD has been through many partinioning schemes, and a few heavy operations (such as moving around 200GB of data). Because of the above, I am already 70% sure the problem is with the hard drive. Before I replace it, however, I want to rule out other less likely possibilities (such as RAM, software, or PSU). I don't have the money to replace the entire box right now, but I can easily replace one of the components. I've read several questions (such as this one) which give general guidance on troubleshooting an unknown issue, that is not what I'm looking for here. My main question is: What tests or benchmarks can I run to verify I have a problematic hard drive? I don't need to solve this problem, I am content with just making sure it's the hard drive. I could borrow a newer hard drive from a friend and see if it gets better. A positive result would rule out all other components, but it wouldn't rule out a software issue (since this new hard drive won't have any of the software I use daily). Running on Windows/Linux.

    Read the article

  • Why do I get this message from chrome when navigating to https://www.amazon.com?

    - by Denis
    This is probably not the site you are looking for! You attempted to reach www.amazon.com, but instead you actually reached a server identifying itself as *.voxcdn.com. This may be caused by a misconfiguration on the server or by something more serious. An attacker on your network could be trying to get you to visit a fake (and potentially harmful) version of www.amazon.com. Intermittently, I get a blank page when going to http://www.amazon.com. So I stuck an 's' in the URL, making it https://www.amazon.com and got that message above (with the nice red screen) from Chrome indicating there might be some monkey business going on. After hammering on the URL a bunch of times and pulling it up in Chrome's developer tool to look at the network traffic on it, the url (without the s) started behaving. The url with the s just hangs, but the red screen no longer comes up. Some specs... I've got a macBook Pro, Snow Leopard, Time Warner cable. I've had enough strange stuff happening over the past couple months (google.com, youtube.com, amazon.com not coming up or loading strange error messages with random reference numbers) that I finally decided to switch to OpenDNS. Still having problems, though.

    Read the article

  • Mirror a Dropbox repository in Sharepoint and restrict access

    - by Dan Robson
    I'm looking for an elegant way to solve the following problem: My development team uses Dropbox for sharing documents amongst our immediate group. We'd like to put some of those documents into a SharePoint repository for the larger group to be able to access, as granting Dropbox access to the group at large is not ideal. However, we'd like to continue to be able to propagate changes to the SharePoint site simply by updating the files in Dropbox on our local client machines, and also vice versa - users granted access on SharePoint that update files in that workspace should be able to save their files and the changes should appear automatically on our client PC's. I've already done the organization of the folders so that in Dropbox, there exists a SharePoint folder that looks something like this: SharePoint ----Team --------Restricted Access Folders ----Organization --------Open Access Folders The Dropbox master account and the SharePoint master account are both set up on my file server. Unfortunately, Dropbox doesn't seem to allow syncing of folders anywhere above the \Dropbox\ part of the file system's hierarchy - or all I would have to do is find where the Sharepoint repository is maintained locally, and I'd be golden. So it seems I have to do some sort of 2-way synchronization between the Dropbox folder on the file server and the SharePoint folder on the file server. I messed around with Microsoft SyncToy, but it seems to be lacking in the area of real-time updating - and as much as I love rsync, I've had nothing but bad luck with it on Windows, and again, it has to be kicked off manually or through Task Scheduler - and I just have a feeling if I go down that route, it's only a matter of time before I get conflicts all over the place in either Dropbox, SharePoint, or both. I really want something that's going to watch both folders, and when one item changes, the other automatically updates in "real-time". It's quite possible I'm going down the entirely wrong route, which is why I'm asking the question. For simplicity's sake, I'll restate the goal: To be able to update Dropbox and have it viewable on the SharePoint site, or to update the SharePoint site and have it viewable in Dropbox. And since I'm a SharePoint noob, I'll also need help hiding the "Team" subfolder from everyone not in a specific group in AD.

    Read the article

  • Could this server log mean my server is being used as a proxy?

    - by So Over It
    I came across the following entry in my access.log: 58.218.199.147 - - [05/Jun/2012:12:56:04 +1000] "GET http://proxyproxys.com/ HTTP/1.1" 200 183 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1)" Normally when I see a full URL entry in my access.log I assume it is log spam with people trying to get me to access their site. These entries are normally followed with a 404 response. The above entry is followed with a 200 'success' response! Doing some searching it would seem that this can occur when someone is trying to use your server as a proxy. This disturbed me more - especially because the URL in question has the word proxy in it. Going to the site 'proxyproxys.com' (using hidemyass.com to protect my own identity), the site returns what appears to be some sort of 'proxy judge' ---------------------------------------- HTTP_ACCEPT=text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 HTTP_ACCEPT_LANGUAGE=en-US,en;q=0.8 HTTP_USER_AGENT=Mozilla/5.0 (Macintosh; Intel Mac OS X 10_7_4) AppleWebKit/536.5 (KHTML, like Gecko) Chrome/19.0.1084.53 Safari/536.5 HTTP_CONNECTION=close REMOTE_PORT=56355 REMOTE_HOST=74.63.112.142 REMOTE_ADDR=74.63.112.142 ---------------------------------------- CS_ProxyJudge Result=HIGH_ANONYMITY ---------------------------------------- Question: 1) does the 200 success mean that someone has been able to successfully use my server as a proxy? 2) are there other means of confirming if my server is being used as a proxy 3) can you refer me to documentation to help 'close up' my security gap if there is one. Thanks.

    Read the article

  • How to change mod_rewrite to avoid {REQUEST_FILENAME} in order to get around 255 character URL limit?

    - by Jeremy Reimer
    According to this answer: max length of url 257 characters for mod_rewrite? there is a maximum 255 character hard limit based on the file system for using mod_rewrite. According to the accepted answer, there are two solutions: Change the URL format of your application to a max of 255 characters between each slash. Move the Rewrite rules into the apache virtual host config and remove the REQUEST_FILENAME. I cannot use the first method, so I am trying to figure out the second. I have put the Rewrite rules into the Apache virtual host config as requested. However I cannot figure out how to remove the REQUEST_FILENAME and still have my web application framework (Dragonfly) still work. Here is the portion of the rewrite rules that I moved from .htaccess into the virtual host config file of Apache: RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_FILENAME} !-l RewriteCond %{REQUEST_FILENAME} !-f [OR] # if don't want Dragonfly to process html files comment # out the line below (you may need to remove the [OR] above too). RewriteCond %{REQUEST_FILENAME} \.(html|nl)$ # Main URL rewriting. RewriteRule (.*) index.cgi?$1 [L,QSA] I've tried removing {REQUEST_FILENAME} and it just breaks the framework in various ways. How do I rewrite this without using {REQUEST_FILENAME}?

    Read the article

  • How to stop DW20.exe running on Win 2003 Server

    - by Laurence
    Periodically my ASP.NET application crashes (usually because memory consumption exceeds maximum allowed by application pool) and DW20.exe starts up. This is a big problem because it uses huge amounts of memory and CPU for minutes at a time. I want to know how to stop DW20.exe from running. Please note, I have already tried these often mentioned solutions: Disabling error reporting in Control Panel System Advanced Error Reporting Disabling the Error Reporting Service Modifying the registry as in http://support.microsoft.com/kb/841477 (however I might have done this wrong - this doc says "add a DWReportee value of 1" - what I did was add a DWORD entry with hexadecimal value of 1 - is this right? Also only 2 of the 4 keys were present, so I only modified these, e.g. there was no HKEY_LOCAL_MACHINE\Software\Policies\Microsoft\PCHealth key at all) So, zero points for suggesting any of the above (unless you can see I have modified the registry incorrectly)! Also zero points for suggesting I resolve whatever is causing the application crashes :) - I am figuring this out, I just want something in the mean time to stop DW20.exe eating up all the server resources. By the way, this is a Windows 2003 SP1 server, with IIS 6 and SQL 2005 installed. There is no MS Office.

    Read the article

  • Windows Server 2008 RAID10

    - by JT
    Hello All, I am building a storage system for myself. I have a 16 bay SATA chasis and right now I have 1 x 500GB SATA for booting 8 x 1.5TB for data. 3Ware 9500S-8 RAID card where these 8 drives above are connected to. I am used to linux, but not in the RAID department. I have Windows experience too. What I am looking for is something that I can just let sit, be reliable and use for other items as well. (Like running test websites, Apache, MySQL, etc). This box is private on a Class-C subnet. My thought is to at least consider Windows Server 2008. I especially like the potential for NON-GUI Mode. Can Windows Server 2008 do a Software RAID 10 out of the box? Software RAID is better performance and better in case the raid needs to be moved to another machine? I just want to SCP files, so OpenSSH running on it? Can one install the GUI, but not use it unless they get in a bind? Is Windows a good idea or should I stick to a Linux Software RAID or FreeBSD + ZFS?

    Read the article

  • Samba between Ubuntu server 10.10 and Windows Vista, Windows 7

    - by chepukha
    Hi all, I have a linux box running Linux server ubuntu 10.10. I have installed Samba on this linux box and want to share files with my laptops which run Windows Vista home and Windows 7 home. I have been struggling with the setup for almost a month but couldn't get it right. If I try to access share folder from Windows Vista, I get message "Windows cannot access \\server_ip_address". Error code: 0x80070035. The network path was not found. If I access from Windows 7, then after entering password to login I can see the list of share folders on Linux box. But if I click on a share folder, I get the same error message as above. Tail /var/log/samba/log.windows7-pc I got the following message: [2011/03/16 00:17:41.427238, 0] smbd/service.c:988(make_connection_snum) canonicalize_connect_path failed for service sharemedia, path /root/sharemedia Here is my setting in smb.conf [global] share modes = yes netbios name = Samba workgroup = WORKGROUP wins support = yes encrypt passwords = true [sharemedia] comment = Tesing sharing using Samba path=/root/sharemedia/ public = yes valid users = samba_usr_name ; make sure all files are sensible permissions create mask = 0660 force create mask = 0660 directory mask = 2770 force directory mask = 2770 directory security mask = 0000 ; Normal share parameters read only = no browseable = yes writable = yes guest ok = no

    Read the article

  • Zero sized tar.gz file found inside a tar.gz file

    - by PavanM
    My current directory contains a single file like this- $ls -l -rw-r--r-- 1 root staff 8 May 28 09:10 pavan Now, I want to tar and gzip this file like $tar -cvf - * 2>/dev/null |gzip -vf9 > pavan.tar.gz 2>/dev/null (I am aware I am creating the zipped file in the same directory as the original file) When I run the above tar/gzip commands around 20 times, a few times I observe that the final tarred and zipped file pavan.tar.gz file has a ZERO sized pavan.tar.gz file. I am not sure from where is this zero sized file coming into the archive from. Note: I am NOT running tar/gzip commands on an already existing tar.gz file. I always make sure that the directory has only one file before running the commands On googling, as described here, I suspected that the tar.gz being created was also part of the file being archived. But in my case, gzip is the one who's creating the final file and by the time gzip runs, tar should be done tarring. This is happening on AIX but I've used Linux tag too, to draw more attention, as I guess the problem is platform independent.

    Read the article

  • How to Change the Kerberos Default Ticket Lifetime

    - by user40497
    Our KDC servers are running either Ubuntu Dapper (2.6.15-28) or Hardy (2.6.24-19). The Kerberos software is the MIT implementation of Kerberos 5. By default, a Kerberos ticket lasts for 10 hours. However, we'd like to increase it a bit (e.g. 14 hours) to suit our needs better. I had done the following but the ticket lifetime still stays at 10 hours: 1) On all the KDC servers, set the following parameter under [realms] in /etc/krb5kdc/kdc.conf and restarted the KDC daemon: max_life = 14h 0m 0s 2) Via "kadmin", changed the "maxlife" for a test principal via "modprinc -maxlife 14hours ". "getprinc " shows that the maximum ticket life is indeed 14 hours: Maximum ticket life: 0 days 14:00:00 3) On a Kerberos client machine, set the following parameters under [libdefaults], [realms], [domain_realm], and [login] in /etc/krb5.conf (everywhere basically since nothing I tried had worked): ticket_lifetime = 13hrs default_lifetime = 13hrs With the above settings, I suppose that the ticket lifetime would be capped at 13 hours. When I do "k5start -l 14h -t ", I see that the end time for the "renew until" line is now 14 hours from the starting time: Valid starting Expires Service principal 04/13/10 16:42:05 04/14/10 02:42:05 krbtgt/@ renew until 04/14/10 06:42:03 "-l 13h" would make the end time in the "renew until" line 13 hours after the starting time. However, the ticket still expires in 10 hours (04/13 16:42:05 - 014/14 02:42:05). Am I not changing the right configuration file(s)/parameter(s), not specifying the right option when obtaining a Kerberos ticket, or something else? Any feedback is greatly appreciated! Thank you!

    Read the article

  • A Domain Admin user doesn't have effective Administrative rights on a Domain Computer

    - by rwetzeler
    I am a developer who is setting up a virtual domain environment of testing purposes and am having trouble with the setup. I have created a new DC on a new Forest... call it dev.contoso.com. I have setup a virtual internal network for all machines that are going to be apart of this virtual test environment and have given each machine a static IP address in the 192.169.150.0 subnet. I have added machine1.dev.contoso.com to the domain dev.contoso.com. I have also provisioned a user account (adminuser) in the domain and made that user a member of Domain Admins group. Upon logging into machine1 using my newly created Domain Admin account, I cannot access/run any files on machine1. When I go into the advanced permissions for the c:\ folder and goto properties - Security Tab - Advanced - Effective Permissions and search for the dev\adminuser (mentioned above), I get an error saying: Windows can't calculate the effective permissions for admin user What do I need to do to get Administrative rights on Machine1? I am using Server 2008 R2 for both the AD controller and machine1.

    Read the article

  • haproxy: Is there a way to group acls for greater efficiency?

    - by user41356
    I have some logic in a frontend that routes to different backends based on both the host and the url. Logically it looks like this: if hdr(host) ends with 'a.domain.com': if url starts with '/dir1/': use backend domain.com/dir1/ elif url starts with '/dir2/': use backend domain.com/dir2/ # ... else if ladder repeats on different dirs elif hdr(host) ends with 'b.domain.com': # another else if ladder exactly the same as above # ... # ... else if ladder repeats like this on different domains Is there a way to group acls to avoid having to repeatedly check the domain acl? Obviously there needs to be a use backend statement for each possibility, but I don't want to have to check the domain over and over because it's very inefficient. In other words, I want to avoid this: use backend domain.com/url1/ if acl-domain.com and acl-url1 use backend domain.com/url2/ if acl-domain.com and acl-url2 use backend domain.com/url3/ if acl-domain.com and acl-url3 # tons more possibilities below because it has to keep checking acl-domain.com. This is particularly an issue because I have specific rules for subdomains such as a.domain.com and b.domain.com, but I want to fall back on the most common case of *.domain.com. That means every single rule that uses a specific subdomain must be checked prior to *.domain.com which makes it even more inefficient for the common case.

    Read the article

  • How to handle server failure in an n-tier architecture?

    - by andy
    Imagine I have an n-tier architecture in an auto-scaled cloud environment with say: a load balancer in a failover pair reverse proxy tier web app tier db tier Each tier needs to connect to the instances in the tier below. What are the standard ways of connecting tiers to make them resilient to failure of nodes in each tier? i.e. how does each tier get the IP addresses of each node in the tier below? For example if all reverse proxies should route traffic to all web app nodes, how could they be set up so that they don't send traffic to dead web app nodes, and so that when new web app nodes are brought online they can send traffic to it? I could run an agent that would update all the configs to all the nodes, but it seems inefficient. I could put an LB pair between each tier, so the tier above only needs to connect to the load balancers, but how do I handle the problem of the LBs dying? This just seems to shunt the problem of tier A needing to know the IPs of all nodes in tier B, to all nodes in tier A needing to know the IPs of all LBs between tiers A and B. For some applications, they can implement retry logic if they contact a node in the tier below that doesn't respond, but is there any way that some middleware could direct traffic to only live nodes in the following tier? If I was hosting on AWS I could use an ELB between tiers, but I want to know how I could achieve the same functionality myself. I've read (briefly) about heartbeat and keepalived - are these relevant here? What are the virtual IPs they talk about and how are they managed? Are there still single points of failure using them?

    Read the article

  • Exchange eMails In A Mailbox Appear To Be Blocked By A Dud Message

    - by John Judd
    I have a client with an Exchange server on which there are quite a few mailboxes. One mailbox in particular is causing some problems. When an email from a certain address arrives, it appears to prevent Exchange from successfully delivering the email to the Outlook Express inbox. The address in question is from an account with Bigpond, or at least I think it is, I didn't check to see if it was spoofed (only just occurred to me.) Any emails in the queue before the suspect email are delivered, then Express times out. When send/recv is retried those emails are re-received and the process times out again. The process I have for fixing this is to log in to the sever, load Outlook, open the recipients inbox, and delete the suspect email. Then retrying the send/recv on Express successfully retrieves all the messages (except for the deleted message.) This solves the immediate problem, but this has happened several times now, and each time requires the process above to correct it. What I am wondering is if there is anything I can do to fix this permanently. It seems to me that Exchange should reject a dud email message rather than getting stuck. Does anyone know what could be causing this, and how I can fix it?

    Read the article

  • Purge print driver cache on windows 7 with powershell script

    - by Doltknuckle
    [Background] We have been having trouble with our network clients suddenly being unable to print. They get an odd error with a hex code. We determined that something in the driver was messed up and we could resolve the issue by clearing the driver cache and reinstalling the driver. This happens to random computers every so often. We're assuming this is a bug with the latest Dell 2330dn driver since that is the only model that has this problem. [Problem] What we are looking to do is write a Powershell script that would clear the driver cache and redownload the driver. I see a ton of scripts out there to manage queues, servers, and ports, but nothing for local driver cache management. [Current Workaround] Since we have to do this manually, I'll write out the steps so you know what we want this script to replicate. Disable print spooler Restart machine Delete contents of: C:\windows\system32\spool\drivers\w32x86 Enable print spooler and start service. Delete the network printer object and re-add network printer off of server. [Request] I'm good enough with powershell to translate the above workaround into a pair of scripts. I'd like to find a more elegant solution then my current workaround. Any suggestions?

    Read the article

  • Windows Vista: Screen remains darkened for 30-60 seconds *after* UAC prompt

    - by sf2k
    Fixing someone's Vista computer. Process: I click any program or process that opens a User Account Control prompt. Screen goes dim so you may hit Continue to perform a secure user action. I click Continue Screen goes black for 30 seconds to 1 minute while you wait for the screen to return. In another example I click Cancel and screen still then goes black for 30 seconds to a minute. In that timeframe a chime goes off while you wait. (No chime if it was being cancelled.) Then screen comes back to continue with whatever. Something is occurring after the UAC prompt. Considering everything is practically a UAC acceptance this can get pretty annoying pretty quickly. Laptop has external monitor to regular external plug. Works fine. Laptop also has USB IOGEAR additional external video card. This is problematic but when unplugged same above behaviour occurs. I've ruled out monitor interference since same blackout after the UAC prompt appears with external monitors plugged in or when rebooted with no external monitors. Any suggestions on how to address this problem?

    Read the article

  • Windows 7 Not Starting and System Repair Not Loading

    - by Mark
    I have a Dell Inspiron 1545 running Windows 7 When turning on my PC I keep receiving a black screen with the option to use System Repair or Start Normally. Both options lead me to the System Repair background except no matter how long I wait the system restore options never show up. Choosing F8 and running all of the options including safe mode encounters the same result above. I tried to to use 2 system recovery disks 32x and 64x I downloaded and both lead to similiar results. When I choose System Repair running from the disk the System Repair Question asking to select a language pops ups but after this no matter how long I wait no other options appear. Next after restarting and selecting F8 (after hitting f12 and running from CD) I choose 'Run From Safe Mode with Command Prompt' I am able to run all of the options from System Restore with differing results: Startup Repair: Choosing this ends up in system repair indefinitely (left running 12 hrs) System Restore: Does Nothing. PC thinks for a second and then stops. When selecting ShutDown I see an error message stating there are no restore points. System Image Recovery: Service Cannot be started in Safe Mode Windows Memory Diagnostic: Runs test but then leads to system repair background which never loads system repair Command Prompt: chkdsk /r -Cannot Lock Current Drive...write protected. chkdsk /f -Cannot Lock Current Drive...write protected. bootcfg - Cannot open Boot.Ini file bootcfg - Ran all 3 (rebuildBcd, FixMbr and Fixboot) but PC still goes to System Repair background with no repair options popping up upon restart (without recovery CD). I'm on the verge of purchasing a boot utility disk for $50 unless there is anything else short of "take it to a computer shop" that somebody can suggest I try.

    Read the article

  • Remote desktop solution where the desktop sharing party contacts the computer it wants to share with

    - by Kent
    I'm in a situation where I act as a sort of techinical support to my family and less techinically experienced friends. I'm looking for a remote desktop solution where it's possible to setup a "zero-install, double click an icon"-solution where the client computer contacts me so that I may interact with their desktop. The last part is important as the people in need of my help don't know how to configure their router or even the firewall software on their own computer. They are able to click an accept button when asked if a program should be able to make outgoing connections. They have many different kinds of routers, as well as software firewalls, and I rather not deal with the problem of how to connect to them using whatever as well as the actual problem they are having. It must be: Free of charge for non-commercial use. Possible to use it in a mode where the computer wanting to share its desktop should be able to make a connection to my computer. My computer has a DNS name we can use. Compatible with both Windows XP and Windows 7. Independent of a third party server or infrastructure. Explanations of the above: I don't want to spend money on it when I help them for free. If it's free as in freedom, all the better! I guess this boils down to being callable like showdesktopto.exe opscomputer.com where opscomputer.com is my computers DNS name. If that is possible then I can create a shortcut they can use to connect to me when they need help. It's nice if it's possible to specify a password or key file which I can use to authenticate myself, but it's not required. They use the OS which their machine comes installed with. That means Windows XP or 7. I want something which will work in the long run. Using a third party service which might not be available when I need it disqualified such solutions.

    Read the article

  • Why won't 2GB of ram across 3 of 4 slots work on my motherboard (max 2GB)?

    - by Andrew
    My desktop is an old home-built machine circa 200[5-6] running Ubuntu 11.10 (but this is not relevant because I'm reading available ram from BIOS loading screen), with an ASUS P5GPL motherboard, not X or X-SE - it has four slots. I'm mainly a laptop person, but keep this around for running a server from if needed, backing up to, seeding Ubuntu to people from, etc… It has four (DDR) ram slots, two black and two blue, in the order black-blue-black-blue (I will call them D, C, B, and A, respectively) with some space in the middle. The blue ones are the closest to the processor. I used to have two 512MB chips in the two blue slots. I just got a 1GB chip and plugged it into one of the black slots; my system didn't recognize it. I messed around and discovered that it will not recognize chips in many positions, and I couldn't get it to recognize all three of these chips at the same time. In particular, if I put the 512MB chips in A and B it would only use 1, but AC, AD, BD, and CD worked. I didn't try BC, I believe. Only some of these continue to work when I switch the 1GB chip into one of these positions. Can I have some advice as to how to position these chips to get all 2GB used? How about if I get another 1GB chip - where should I put the two? And what about the RAM maximum Crucial says? Can I go above 2GB, if I get another 1GB chip? Right now, I have a 512MB chip in A and the 1GB chip in C. EDIT: I read some other posts and tried dmidecode in Ubuntu to clarify the max memory question, that wasn't a major part anyways. It says my max memory module size is 1024M (OK) and my max memory size is 4096M (doesn't agree with Crucial OR the Asus web site, maybe it will only work while in Linux and BIOS won't OK it?).

    Read the article

  • Apache 2 proxy for Tomcat 7

    - by hsnm
    Following the how-to, I wanted to make a proxy for traffic to the address /app to be processed by Tomcat 7. I added this to my httpd.conf: LoadModule proxy_module {path-to-modules}/mod_proxy.so LoadModule deflate_module modules/mod_deflate.so ProxyPass /app http://localhost:8081 ProxyPassReverse /app http://localhost:8081 I also have this on my server.xml: <Connector port="8081" enableLookups="false" acceptCount="100" connectionTimeout="20000" proxyName="localhost" proxyPort="80"/> And I have the folder /var/lib/tomcat7/webapps/app with my application files. I restarted both Tomcat 7 and Apache 2 after doing the configurations above. Problem: When navigating to my webpage.com/app, I get the error 500. I consulted apache logs, it says: [warn] proxy: No protocol handler was valid for the URL /app. If you are using a DSO version of mod_proxy, make sure the proxy submodules are included in the configuration using LoadModule. Update: This is running in ubuntu. I resolved this by adding LoadModule proxy_http_module modules/mod_proxy_http.so to my httpd.conf. Now I have another question: How can I make this proxy to work on SSL through port 443?

    Read the article

  • Windows 2012 Server: Enable .NET 3.5

    - by Meengla
    I have a Windows 2012 Server which needs .NET 3.5 installed. For background info/solutions, please see this: http://sqlblog.com/blogs/sergio_govoni/archive/2013/07/13/how-to-install-netfx3-on-windows-server-2012-required-by-sql-server-2012.aspx I have tried this but it doesn't work for me. Here is what I am trying: Using a Windows 2012 ISO file, 'mount' on the 2012 Server as 'D' drive and then tried both GUI and Command prompt. In case of GUI, I specified the 'alternate source' path to the D drive's 'source/sxs folder but that failed without giving enough info. In case of the command prompt, here is what's happening: dism /online /enable-feature /featurename:NetFx3 /source:d:\sources\sxs I get error: Installed but Parent feature not enabled. So I tried another approached: dism /online /enable-feature /featurename:NetFx3 /all /source:d:\sources\sxs the above command, per http://blogs.technet.com/b/askcore/archive/2012/05/14/windows-8-and-net-framework-3-5.aspx is supposed to enable parent elements; but running this I get error like 'source not found'. Is there some error in my second command? What else I could do? This is Windows 2012 Server Standard edition. Thanks!

    Read the article

  • Computer loses all installed programs and appears to return OS-only state

    - by Jake
    This is a story regarding 3 laptops of different brand and models. On separate occassions, I configured each of these Windows 7 / Vista computers with the necessary configuration and applications (which are supposedly the same actually), e.g. join office domain, same windows updates, microft office etc. These machinese were configure in our office in Singapore, and then they were taken to India for use. Someday in India, when booting up the laptop, all went fine except when it reach the log in screen, it was no longer possible to login with domain credentials. Logging into the laptop local admin account will lead to discover that the machine has returned to "OS-only state". All the configurations and applications were gone. The actual user profiles are still in the C: drive so files can still be retrieved, but under Control Panel Uninstall Programs it is evident that at least the registry is corrupted. The above scenario happen to the first 2 laptops. For the third, the system reports "Operating System Not Found" on boot up. I cannot think of any reason except to suspect a power fluctuation issue. Question is, will a power issue create this behaviour? What else can cause this issue?

    Read the article

  • CopSSH SFTP -- limit users access to their home directory only

    - by bradvido
    Let me preface this by saying I've read and followed these instructions at the FAQ many times: http://www.itefix.no/i2/node/37 It does not do what the title claims... It allows every user access to every other user's home directory, as well as access to all subfolders below the copssh installation path. I'm only using this for SFTP access and I need my users to be sandboxed into only their home directory. If you know a fool-proof way to lock users down so they can see only their home directory and its subfolders, stop reading now and reply with the solution. The details: Here is exactly what i tried as I followed the FAQ. My copSSH installation directory is: C:\Program Files\CopSSH net localgroup sftp_users /ADD **Create a user group to hold all my SFTP users cacls c:\ /c /e /t /d sftp_users **For that group, deny access at the top level and all levels below cacls "C:\Program Files\CopSSH" /c /e /t /r sftp_users **Allow my user group access to the copSSH installation directory and its subdirectories For each sftp user, I create a new windows user account, then I: net localgroup sftp_users sftp_user_1 /add **Add my user to the group I've created Open the activate user wizard for CopSSH, choosing the user, "/bin/sftponly" and Remove copssh home directory if it exists **Remains checked Create keys for public key authentication **Remains checked Create link to user's real home directory **Remains checked This works, however, every user has access to every other user's home directory as well as the CopSSH root directory.... So I tried denying access for all users to the user home directory: cacls "C:\Program Files\CopSSH\home" /c /e /t /d sftp_users **Deny access for users to the user home directory Then I tried adding permissions on a user-by-user basis for each users home\username folder. However,these permission were not allowed by windows because of the above deny rule i created at the home directory was being inherited and over-riding my allow rule. The next step for me would be to remove the deny rule at the home directory and for each user folder, add a deny rule for every user it doesn't belong to, and add an allow rule for the one user it does belong to. However, as my user list gets long, this will become very cumbersome. Thanks for the help!

    Read the article

  • How can I get WAMP and a domain name to work on a non-standard port?

    - by David Murdoch
    I have read countless articles on setting up a domain on WAMP to listen on a port other than 80; none of them are working. I've got Windows Server 2008 (Standard) with IIS 7 installed and running on port 80 (and 443). I've got WAMP installed with the following configuration. Listen 81 ServerName sub.example.com:81 DocumentRoot "C:/Path/To/www" <Directory "C:/Path/To/www"> Options All MultiViews AllowOverride All # onlineoffline tag - don't remove Order Allow,Deny Allow from all </Directory> localhost:81 works with the above configuration but sub.example.com:81 does not. Just to make sure my firewall wasn't getting in the way I have disabled it completely. My sub.example.com domain is already pointing to my server and works on IIS on port 80. Also, if I disable IIS and change the Apache port from 81 to 80 it works. Yes, I am restarting Apache after each httpd.conf change. :-) I don't need any other domain (or sub domains [I don't even care about localhost]) configured which is why I'm not using a VirtualHost. Any ideas what is going on here? What could I be doing wrong? Update Changing Listen to 80 but keeping ServerName as sub.example.com:81 causes navigation to sub.example.com:80 to work; this just doesn't seem right to me. Could ServerName be ignoring the :port part somehow? netstat -a -n | find "TCP": >netstat -a -n | find "TCP" TCP 0.0.0.0:81 0.0.0.0:0 LISTENING TCP 0.0.0.0:135 0.0.0.0:0 LISTENING TCP 0.0.0.0:445 0.0.0.0:0 LISTENING TCP 0.0.0.0:912 0.0.0.0:0 LISTENING ... TCP 127.0.0.1:81 127.0.0.1:49709 TIME_WAIT ...

    Read the article

  • Acronis Disk Director AFTER Clone Disk error: PXE-E61: Media test failure, check cable

    - by Kairan
    Used Acronis Disk Director on my desktop, plugged in the laptop drive 240GB SSD (USB) and the new hard drive 500GB SSD (usb) and the copy seemed to be fine. I didnt see any error messages but I didnt stare at it for 3 hours either. The clone disk of course the Toshiba hidden restore partition, the primary partition C drive and the active (boot?) partition and yes, did check box for copy NT signature. The computer boots up fine most of the time, but it seems that when the computer goes to sleep (i believe its sleep, hard to do much testing during school) or hibernate or reboot it will sometimes display this message: Intel(R) Boot Agent GE v1.3.52 Copyright (C) 1997-2010, Intel Corporation PXE-E61: Media test failure, check cable PXE-M0F: Exiting Intel Boot Agent Insert system disk in drive. Press any key when ready... Of course any key does nothing but repeat a similar method. However, if I press the power button on the laptop (Toshiba Portege R705, Win 7 Pro 64-bit) it puts computer into hibernate. After hibernating I press power button again and it comes out of hibernation without any odd messages or problems described above... so apparently that is my TEMP fix. Another recent issue I noticed is on occasion when creating a new folder or modifying something in the system variables, other random areas I will get a message: "The Stub received bad data" and simply retry the task and it works. Perhaps these two issues are linked.

    Read the article

< Previous Page | 467 468 469 470 471 472 473 474 475 476 477 478  | Next Page >