Search Results

Search found 14757 results on 591 pages for 'switch statement'.

Page 474/591 | < Previous Page | 470 471 472 473 474 475 476 477 478 479 480 481  | Next Page >

• Attempts at NIC teaming on Server 2008 R2 with PRO/1000 MT

  - by Klaus

  I have a Dell PowerEdge 1850 server and a gigabit switch that supports nic teaming (and was configured to do so). The server has a total of four Intel PRO/1000 MT ports, which also support teaming. But.. for some reason Intel does not actually have a version of the drivers/ProSet that will work for these cards on 2008 R2. You have to use the built-in drivers that come with 2008 R2, which do not support the additional features. According to their website, they have no plans to change this. Strangely enough, I experimented with various drivers in an attempt to force it to work. At one point, the teaming was working, but there were side effects (such as the DNS server refusing to start). So now I am back to running just one of the cards, (very) frustrated about the whole situation. I have looked all over to see if there is some way around this, but have not had any success. I know I can probably just get a new network adapter for it, but with the good deal I got, that would cost more than the server! :) While staying with 2008 R2, does anyone know of any possible alternatives? Thanks!

  Read the article

• NetApp FAS270 head doesn't see disks

  - by wfaulk

  I have an FAS270C. For months, I've been running it in a split-head manner (that is, with each head serving data totally independently, and without any clustering even being enabled) in order to facilitate moving some data around. I finally got everything situated, moved all the data to one of the heads, and was trying to get clustering set back up. Now when I try to install OnTap onto the "new" head, it cannot see any of the disks in the head shelf. (That is, the shelf into which the heads are inserted.) I've booted into maintenance mode, and it shows me that the 0b adapter, which should be the adapter that that shelf and its disks should be presented on, is in "OFFLINE (physical)" state. If I try to enable it with either "storage enable adapter 0b" or "fcadmin online 0b", it waits for about 30 seconds and then says: [fci.initialization.failed:error]: Initialization failed on Fibre Channel adapter 0b. [fci.adapter.online.failed:error]: Fibre Channel adapter 0b failed to come online. There is currently nothing attached to its external 0b port. I've tried it with and without an SFP plugged into it, and with and without its internal termination switch on. The currently active head can see those disks, and can see that two of them are assigned to the other head. Before I started reconfiguring, the "new" head could see disks on that shelf. They may even be the same disks that OnTap was installed on previously. Does anyone have any idea how to proceed?

  Read the article

• Software for handling camera RAW-files

  - by Eikern

  I use a digital SLR as most other photographers do today and have quickly realised that capturing images using camera-RAW files is the way to go. Personally I use Adobe Lightroom to handle my photo library, but I know there are other software available like Apple Aperture. These applications are quite hard to use for a novice, and are quite expensive too. I've often recommended other photographers to switch to camera-raw, but they won't do it because Windows can't handle it natively. Are there any free or cheaper applications out there that can do simple file handling and adjustments? Preferably so simple that my mom can do it. I know Nikon offers a codec that allows you to view NEF-files natively inside Windows, but still limits the uses of the file and slows the system down if the file is big. Does anybody know of a drag-and-drop application that converts camera-raw to JPG on-the-fly? In case I or someone would need to upload an image to the web or use it inside a word-document. Thanks.

  Read the article

• Options for synchronizing Palm Desktop calendars

  - by Al Everett

  My wife and I each have Palm Centro phones and very full calendars. We've been using Palm products for years and are happy with them and are not looking to switch (and don't have the budget for it even if we wanted to). What is a viable way we can synchronize our calendars? Back when we had Palm Z22s we used AirSet. It worked great in synchronizing our desktop calendars. Unfortunately, their sync software does not support Palm Desktop v6 and there is nothing in the pipeline to support it. (The third party vendor is apparently not interested in updating for the newer Palm desktop.) I would love to be able to get back to having each other's appointments appear on the other's calendar. What can we do? Some limitations: A data plan is not an option (so this precludes over-the-air synchronization options) No Microsoft Outlook Edit: Syncing my Palm to my Palm Desktop is not the issue. Being able to sync, in some way, the Palm calendar databases of my wife's and my calendars is what's desired.

  Read the article

• Dell Inspiron 1564 overheating but fan not switching on, how to diagnose?

  - by Smugrik

  I've got a Dell Inspiron 1564 laptop that is about one and a half years old. Since about a week, the laptop started to overheat, causing it to switch off unexpectedly... The cpu fan is working erratically, it can start to spin for a while, doing its job and cooling down the cpu before it stops, but then the temperature goes up, and the fan doesn't reacts, once the temperature reaches a critical point (over 85 celsius, checked with speedfan...), the laptop switches off... I already cleaned the vents and fan from dust, to no avail, and it was actually quite clean anyway. Drivers and bios are up-to-date, no crapware was ever installed on this machine. I don't know how to diagnose the problem, could it be the temperature sensors that sends wrong information, so the fan doesn't reacts? but then I believe the computer wouldn't detect the overheat and stop... Is there a way I can pin point the problem? Maybe some low-level diagnostic tools to check functionality of sensors and fans??? The warranty is already over so any suggestion would be welcome. Thanks!!

  Read the article

• Nexus 1000v VEM fails on 2 out of 8 hosts.

  - by cougar694u

  I have 8 ESXi hosts. I do a fresh install from the installable CD directly to 4u1. We have another 2-node cluster with a working Nexus 1000v primary & secondary. Everything's up and running. I installed 6 hosts and everything worked great, migrated them to the Nexus DVS, and VUM installed the modules. I did the 7th host, and when I tried to migrate it to the DVS, it failed with the following error: Cannot complete a Distributed Virtual Switch operation for one or more host memebers. DVS Operation failed on host , error durring the configuration of the host: create dvswitch failed with the following error message: SysinfoException: Node (VSI_NODE_net_create) ; Status(bad0003)= Not found ; Message = Instance(0): Inpute(3) DvsPortset-0 256 cisco_nexus_1000v got (vim.fault.PlatformConfigFault) exception Then, I tried to do host 8, and got the exact same problem. It worked about 15 minutes prior when I did host 6, nothing changed, then went to host 7 and it failed. If I try to remediate either of these two hosts, either patches or extensions, it fails. Anyone else have these problems?

  Read the article

• How can I find out which processes on my computer are accessing the microphone?

  - by Vinayak

  After reading this interesting Lifehacker post and reading the comments on the page, one person was wondering if it would be possible to use the Physical Device Object Names of other hardware such as the microphone to find out the names of processes using that device. I tried the same approach, but so far it only seems to work for the webcam. Is there any other way I could get this to work in Process Explorer? UPDATE: The Lifehacker post was about finding out which Windows process is currently using your webcam. This is how they went about doing it: Start Device Manager (WIN+R → "devmgmt.msc" → OK) Find your webcam among the list of devices (check under Imaging Devices) Open the properties window of the device and switch to the Details tab (Right click → Properties → Details) In the dropdown menu, select Physical Device Object Name and copy the string(Right click → Copy) Download Process Explorer Make sure you have opened Process Explorer in Administrator Mode(File → Show Details for All Processes) Hit CTRL+F and enter the string you copied earlier(it should be something like \Device\000000XX) Hit the Search button and you should see a list of processes using the webcam(if there are any)

  Read the article

• Packet drop measured by ethtool, tcpdump and ifconfig

  - by Rayne

  Hi all, I have a question regarding packet drops. I am running a test to determine when packet drops occur. I'm using a Spirent TestCenter through a switch (necessary to aggregate Ethernet traffic from 5 ports to one optical link) to a server using a Myricom card. While running my test, if the input rate is below a certain value, ethtool does not report any drop (except dropped_multicast_filtered which is incrementing at a very slow rate). However, tcpdump reports X number of packets "dropped by kernel". Then if I increase the input rate, ethtool reports drops but "ifconfig eth2" does not. In fact, ifconfig doesn't seem to report any packet drops at all. Do they all measure packet drops at different "levels", i.e. ethtool at the NIC level, tcpdump at the kernel level etc? And am I right to say that in the journey of an incoming packet, the NIC level is the "so-called" first level, then the kernel, then the user application? So any packet drop is likely to happen first at the NIC, then the kernel, then the user application? So if there is no packet drop at the NIC, but packet drop at the kernel, then the bottleneck is not at the NIC? Thank you. Regards, Rayne

  Read the article

• Using two ports on my ZyXel USG gateway to patch two devices together?

  - by Matthew Beza

  I don't know if this is possible but it would save me many long drives! I have drawn, with my epic MS Paint skills, my current setup. I have a ZyXel USG300 Gateway with a built in 5 port switch. It supports bridging, tunnles, VLANs, etc.. I have a Cisco WLC2112 plugged into port 6 (P6). The cisco is set to 192.168.6.2 and P6 is set to 192.168.6.1. This works but I need to incorporate a Nomadix AG3000 to handle guests. (Router (A) in the picture). So I need the Cisco WLC2112 to use the Nomadix as if it where plugged into it's LAN port. Right now the Nomadix WAN Port is plugged into (P2) on the ZyXel, and the Nomadix LAN port is plugged into (P3). Is it possible to set something up where (P3) and (P6) are somehow "Patched" as if the Cisco was plugged directly into the Nomadix LAN port? Basically making the ZyXel a fancy Cat5e coupler?

  Read the article

• When I ping Internet addresses like yahoo or Google, I get 2 reply packets and 2 lost packets.

  - by navi

  I have Airtel broadband and a Tata broadband connection. i have around 50 PCs connecting through an airtel broadband connection. Both are dsl connections with my phone line going into dsl modems and an Ethernet cable going from dsl modem directly into a switch. Currently, only airtel connection is connected with static IP on my private lan and using the airtel ISP DNS servers as DNS IP address and the default gateway is 192.168.1.1 (IP add. of the dsl modem). All PCs are connected in a work group. When in full use, my users complain of certain web pages are not opening. When I ping Internet addresses like Yahoo or Google I get 2 reply packets and 2 lost packets. I suspect that a single broadband connection is not able to sustain 50 simultaneous downloads/browsing. Is there any device which connect to both DSL and make one line so that its give me high speed simultaneous browsing. Help needed urgently. Thank you all to those who reply.

  Read the article

• Why won't 2GB of ram across 3 of 4 slots work on my motherboard (max 2GB)?

  - by Andrew

  My desktop is an old home-built machine circa 200[5-6] running Ubuntu 11.10 (but this is not relevant because I'm reading available ram from BIOS loading screen), with an ASUS P5GPL motherboard, not X or X-SE - it has four slots. I'm mainly a laptop person, but keep this around for running a server from if needed, backing up to, seeding Ubuntu to people from, etc… It has four (DDR) ram slots, two black and two blue, in the order black-blue-black-blue (I will call them D, C, B, and A, respectively) with some space in the middle. The blue ones are the closest to the processor. I used to have two 512MB chips in the two blue slots. I just got a 1GB chip and plugged it into one of the black slots; my system didn't recognize it. I messed around and discovered that it will not recognize chips in many positions, and I couldn't get it to recognize all three of these chips at the same time. In particular, if I put the 512MB chips in A and B it would only use 1, but AC, AD, BD, and CD worked. I didn't try BC, I believe. Only some of these continue to work when I switch the 1GB chip into one of these positions. Can I have some advice as to how to position these chips to get all 2GB used? How about if I get another 1GB chip - where should I put the two? And what about the RAM maximum Crucial says? Can I go above 2GB, if I get another 1GB chip? Right now, I have a 512MB chip in A and the 1GB chip in C. EDIT: I read some other posts and tried dmidecode in Ubuntu to clarify the max memory question, that wasn't a major part anyways. It says my max memory module size is 1024M (OK) and my max memory size is 4096M (doesn't agree with Crucial OR the Asus web site, maybe it will only work while in Linux and BIOS won't OK it?).

  Read the article

• How to set up ProxMox 1.9 on VPN?

  - by Gnudiff

  Disclaimer: I have only rudimentary knowledge of VPNs. I would love to learn about them properly, however, at the moment I really need to make stuff work on short notice. I am trying to set up a ProxMox virtualization platform in an existing network. The network currently consists of several servers which have VMWare free edition. There is some sort of VPN defined in switch. In order for VMWare management interface to be accessible, there needs to be ticked a checkbox in the network settings for VPN and entered the VPN id. I didn't notice any such configuration option during ProxMox installation, so my Proxmox VE on the same physical server, using same manual IP settings (ip/nm/gw), is not accessible. As I understand I should touch the Proxmox's underlying Debian config in /etc/network/interfaces, but I have no idea, what should I aim for: do I specify the settings for eth0, do I make a virtual interface? How to make it accessible for both ProxMox VE and underlying future VMs? I read the ProxMox installation guide, but unfortunately it presumes better understanding of VPNs than I have. A config template or similar would be appreciated. Thanks in advance.

  Read the article

• Cannot print certain colours on Ubuntu with HP Laser Printer

  - by ILMV

  We have a load of machines running Ubuntu in our office, they are either on 8.04 or 9.10. We have a server which connects a HP JetDirect that connects to a HP 3550 Colour Laser printer using CUPS. The problem we are having is we cannot print red, magenta or yellow at 100%, I've got a picture of the Ubuntu test page to demonstrate my problem: This is obviously a pretty big problem as we are constantly receiving documents with these colours and cannot successfully print them off, we cannot just switch the grayscale, our business depends on being able to print colour (seems trivial but we handle lots of artwork). We're using the recommended driver HP Color LaserJet 3550 footmatic/pxljr (recommended), there is another driver in the list labelled HP Color LaserJet 3550 footmatic/hpijs. These are production printers so need to make sure any setting change won't kick is in the nuts. It would appear HPIJS is for HP Inkjets, makes sense I guess. The problem doesn't occur in Windows. RESOLVED I've managed to solve the problem, I did indeed use the HPIJS driver (apparently for inkjets) but it seems to have worked, we're going to roll with it for now to see how we get on with it.

  Read the article

• Connect bluetooth headphones both to PC and phone at the same time

  - by Sergiy Byelozyorov

  I have recently bought Philips SHB6110. Extract from the 13th page of manual: Therefore you can connect your Bluetooth stereo headset. with a Bluetooth stereo enabled phone to both listen to music and lead calls, or with a Bluetooth phone that does not support Bluetooth stereo (A2DP) to lead calls and at the same time to a Bluetooth audio device (Bluetooth enabled MP3 player, Bluetooth audio adapter etc.) to listen to music. Make sure to pair the phone first with your Bluetooth headset, then turn both the phone and headset off to then pair the Bluetooth audio device. With the SwitchStream feature you can listen to music and monitor your calls at the same time. Even while listening to music, you will hear a ring tone when receiving a call and can switch to the call simply by tapping the button. The manual however doesn't specify how do I connect to both device at the same time. I use Toshiba Satellite Pro P300-1CG laptop with Belkin Mini Bluetooth Adapter and Nokia N95 phone. Operating system is Windows 7 64-bit and I have Skype installed. Both phone and compute can be used for listening to music and talking on the phone (on PC via Skype). Best solution would be if I could connect to PC and phone as the same time and monitor calls both mobile and Skype calls while listening music from Winamp. If that is not possible, then I would like at least to be able to listen music from PC, while monitoring calls from mobile. So, please tell me how do I connect both PC and phone to headphones?

  Read the article

• On dual boot system, Is it possible to use VirtualBox to boot other installed OS?

  - by Derek Ziemba

  I currently run Windows 7 from a 256GB SSD as my Operating System. Lately, for school, I've been using openSUSE linux inside a VirtualBox PC and I'm really liking it. I'm starting to hate even working in Windows. But I can't just abandon Windows. I've been considering dual booting openSUSE and will likely purchase another SSD for openSUSE. Once I have the dual boot set-up, there is going to be times I need to do something quick in the operating system that I'm not currently in. It would be a pain to have to reboot the computer each time I need to switch the OS for a simple task, especially from Windows since it doesn't let you save it's state. From openSUSE, I want to be able to start a VirtualBox Machine using my Windows Drive. And in Windows, I want to be able to start a VirtualBox Machine of my openSUSE Drive. Would this be possible? The issue I'm worried about is drivers. For instance, the OS will be installed on native hardware and have the native hardware's drivers configured. When I try to boot the OS in a VirtualMachine, I feel like the OS is not going to know what to do, and have to reconfigure itself or just not work.

  Read the article

• HP Procurve 2610 intervlan routing

  - by user19039

  Can anyone tell me why inter vlan routing is working for all vlans except my newly created vlan 4/ I have an hp procurve 2610. Any help would be appreciated. I have basically this 1 switch with all unmanaged switches attached to the core. We have a second 2610 on port 28 Running configuration: ; J9085A Configuration Editor; Created on release #R.11.25 hostname "Core_HP" interface 22 speed-duplex 100-full exit ip routing snmp-server community "public" Unrestricted vlan 1 name "DEFAULT_VLAN" untagged 1-12,17-22,26-27 ip address 192.168.4.6 255.255.255.0 tagged 25 no untagged 13-16,23-24,28 exit vlan 2 name "WAN" untagged 28 ip address 10.254.254.3 255.255.255.0 exit vlan 3 name "Wireless" untagged 13-16,24 ip address 192.168.7.6 255.255.255.0 ip helper-address 192.168.4.2 tagged 27 exit vlan 35 name "guest" untagged 23 tagged 24 exit vlan 4 name "esxi" untagged 25 ip address 10.10.1.1 255.255.248.0 exit ip route 192.168.5.0 255.255.255.0 10.254.254.1 ip route 192.168.6.0 255.255.255.0 10.254.254.1 ip route 0.0.0.0 0.0.0.0 192.168.4.10 show ip route IP Route Entries Destination Gateway VLAN Type Sub-Type M etric Dist. ------------------ --------------- ---- --------- ---------- - --------- ----- 0.0.0.0/0 192.168.4.10 1 static 1 1 10.10.0.0/21 esxi 4 connected 0 0 10.254.254.0/24 WAN 2 connected 0 0 127.0.0.0/8 reject static 0 250 127.0.0.1/32 lo0 connected 0 0 192.168.4.0/24 DEFAULT_VLAN 1 connected 0 0 192.168.5.0/24 10.254.254.1 2 static 1 1 192.168.6.0/24 10.254.254.1 2 static 1 1 192.168.7.0/24 Wireless 3 connected 0 0 show ip Internet (IP) Service IP Routing : Enabled Default TTL : 64 Arp Age : 20 VLAN | IP Config IP Address Subnet Mask Prox y ARP ------------ + ---------- --------------- --------------- ---- ----- DEFAULT_VLAN | Manual 192.168.4.6 255.255.255.0 No WAN | Manual 10.254.254.3 255.255.255.0 No Wireless | Manual 192.168.7.6 255.255.255.0 No esxi | Manual 10.10.1.1 255.255.248.0 No guest | Disabled

  Read the article

• Change the default route without affecting existing TCP connections

  - by Patrick Horn

  Let's say I have two public network addresses on my server: one NAT through an ISP (192.168.99.0/24), and a VPN through a different ISP (192.168.1.0/24), already configured with a per-host route to the VPN server through my ISP. Here is my initial routing table. I am currently routing through my ISP on subnet 192.168.99.0/24. $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.99.1 0.0.0.0 UG 0 0 0 eth1 55.66.77.88 192.168.99.1 255.255.255.255 UGH 0 0 0 eth1 192.168.99.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 Now, I want new TCP connections to switch to my 192.168.1.0/24 so I type the following: $ route add -net 0.0.0.0 gw 192.168.1.1 dev tap0 When I do this, it causes some long-standing TCP connections to hang. Is there a way to I safely change the default interface for new connections, while allowing existing TCP connections to use the old route (i.e. do I need enable some sort of stateful routing table)? I am okay with a solution that only works with established TCP connections, and I don't care how hacky it is. For example, if there is a way to add temporary iptables rules for existing connections to force them over the old route. But there has to be some way to do this. EDIT: Just a note about a simple "route add -host ... " for existing connections: this solution would work if I am fine with leaving a subset of IPs on the old interface. However, in my application, this actually doesn't solve my problem because I want to allow new connections to come on the new interface even if they have the same source IP. I'm now looking at using the "ip route" command to set source-based routing rules.

  Read the article

• Moving automatically spam messages to a folder in Postfix

  - by cad

  Hi My problem is that I want to automatically to move spam messages to a folder and not sure how. I have a linux box giving email access. MTA is Postfix, IMAP is Courier. As webmail client I use Squirrelmail. To filter SPAM I use Spamassassin and is working ok. Spamassasin is overwriting subjects with [--- SPAM 14.3 ---] Viagra... Also is adding headers: X-Spam-Flag: YES X-Spam-Checker-Version: SpamAssassin 3.2.5 (2008-06-10) on xxxx X-Spam-Level: ************** X-Spam-Status: Yes, score=14.3 required=2.0 tests=BAYES_99, DATE_IN_FUTURE_24_48,HTML_MESSAGE,MIME_HTML_ONLY,RCVD_IN_PBL, RCVD_IN_SORBS_WEB,RCVD_IN_XBL,RDNS_NONE,URIBL_RED,URIBL_SBL autolearn=no version=3.2.5 X-Spam-Report: * 0.0 URIBL_RED Contains an URL listed in the URIBL redlist * [URIs: myimg.de] * 3.5 BAYES_99 BODY: Bayesian spam probability is 99 to 100% * [score: 1.0000] * 0.9 RCVD_IN_PBL RBL: Received via a relay in Spamhaus PBL * [113.170.131.234 listed in zen.spamhaus.org] * 3.0 RCVD_IN_XBL RBL: Received via a relay in Spamhaus XBL * 0.6 RCVD_IN_SORBS_WEB RBL: SORBS: sender is a abuseable web server * [113.170.131.234 listed in dnsbl.sorbs.net] * 3.2 DATE_IN_FUTURE_24_48 Date: is 24 to 48 hours after Received: date * 0.0 HTML_MESSAGE BODY: HTML included in message * 1.5 MIME_HTML_ONLY BODY: Message only has text/html MIME parts * 1.5 URIBL_SBL Contains an URL listed in the SBL blocklist * [URIs: myimg.de] * 0.1 RDNS_NONE Delivered to trusted network by a host with no rDNS I want to automatically to move spam messages to a folder. Ideally (not sure if possible) only to move messages with puntuation 5.0 or more to folder.. spam between 2.0 and 5.0 I want to be stored in Inbox. (I plan later to switch autolearn on) After reading a lot in procmail, postfix and spamassasin sites and googling a lot (lot of outdated howtos) I found two solutions but not sure which is the best or if there is another one: Put a rule in squirrelmail (dirty solution?) Use Procmail Which is the best option? Do you have any updated howto about it? Thanks

  Read the article

• Correcting owner/permissions on damaged directory tree in linux

  - by mcs130

  I inadvertently made a backup copy of a directory recursively and forgot the -a (--preserve) switch when doing so. This damaged my backup directory (which contains data we need to access). The directory and all of its child folders and files comprise an installation of an application including postgress DB and solr files. The original copy was used to for a failed re-config attempt. Now I need to use the backup copy to start over, only the ownership of the backup copy is now root across everything and it is no longer usable (processes won't run due to ownership problems I created when I forgot the -a on the cp -r). I've re-installed a clean copy of the application into a 3rd location now (which has the correct owner/perms) and need to copy the owner/perms from this good directory over onto the damaged directory. What is the best way (if even possible) to do this. (I've Googled and seen things from perl scripting to setfacl/getfacl to do this but am unfortunately still confused). Apologies if this seems a dumb question. Thanks.

  Read the article

• Do you need to advertise an AFP service via Avahi for an Ubuntu Server to show up in OSX Finder?

  - by James

  I am only advertising an NFS share plus the "model", and I don't want to install extra services on the Server unless I have to, ie netatalk, as it is used solely for NFS exports. Currently there is no entry in Finder under "Shared" with below config of Avahi. serveradmin@FILESERVER:/etc/avahi/services$ cat nfs.service <?xml version="1.0" standalone='no'?><!--*-nxml-*--> <!DOCTYPE service-group SYSTEM "avahi-service.dtd"> <service-group> <name replace-wildcards="yes">%h</name> <service> <type>_nfs._tcp</type> <port>2049</port> <txt-record>path=/Volumes/StoragePool</txt-record> </service> <service> <type>_device-info._tcp</type> <port>0</port> <txt-record>model=Xserve</txt-record> </service> </service-group> Server: Ubuntu 12.04.01 x64 Clients: OSX 10.6.8 , 10.7.5, 10.8.2 The goal is to advertise that NFS share, then assign a really old Model code of Mac like a Powermac and switch out the icon for a more "LinuxServer-y" one. Plus allow users to connect to NFS in a manner they are familiar with like our other Xserve servers. I think Avahi is working in general as if I do: nfs://FILESERVER.local/Volumes/StoragePool it will connect fine. Any ideas?

  Read the article

• SQL Server on Linux

  - by TimothyAWiseman

  For a particular project that is coming up, I am trying to expand my knowledge of Linux, so I am going to set up a Linux system at home. Rather than dual booting, I am thinking about putting SQL Server on a Windows Virtual Machine with Linux as the host at least until this project is over when I will probably switch back to Linux. So, I have a couple of different, but interrelated questions: How well does this work? This is only a test machine at home, so I can easily accept a fair bit of degradation, but if it is going to be a horrible reduction in performance I will dual boot instead. Is there a particular virtual machine manager I should look at to go this route? Since this is my personal machine, price is an issue but I am quite happy to pay a reasonable amount. And finally, given the choice of VMM, is there a particular Linux Distro I should be looking at? [This has been cross posted at Ask.SqlServerCentral.com . I think it may be appropriate at both sites. ]

  Read the article

• NATing IPv4 while routing IPv6

  - by Hugo

  I've the following setup: client(s) <---> (eth0) router (eth1) <---> wan I have a static IPv4 address and a /48 IPv6 address block. I need to connect all the clients to (wan). Each client will have it's own public IPv6. Meanwhile, I need to NAT those same clients over to (wan). Everything IPv4-related and the NAT are working fine. The IPv6 communication to/from (eth0)<-(clients) works fine, as does the IPv6 communication from (eth1)<-(wan) works fine. To provide IPv6 to all my clients, I've thought of too choices: Having the router as a gateway, which different IP on each interface. This sounds like I need to tell my ISP to route the entire block through that single IP, so it's not really an option. Transparently pass IPv6 packets to/from eth0<-eth1, so all clients can communicate with the upstream gateway (I would actually have a switch here if it weren't for the need to remain IPv4 compatible). So, since I've opted for the second choice, I'm in doubt: How can I pass all IPv6 traffic from eth0 to eth1 transparently? What I need is a level 3 bridge, but linux's bridgeutils create a level 2 bridge (which would bridge ipv4 as well, and I can't have that). This is a DD-WRT device, but it's pretty much an embeded linux, so most suggestions that would work on linux are welcome. Thanks.

  Read the article

• Most transparent way to connect two LANS using a WET610N Wireless Bridge

  - by Spencer Ruport

  I have two wired systems hooked to a Linksys WRT54GL wired/wireless router which is also hooked to my internet. I'll refer to this as LAN1. I have two more systems in another room that are connected wirelessly. Recently I decided I would much rather have another wired LAN in the other room and use a bridge to connect them. This would be LAN2. Prior to hooking up the device I assumed that the ethernet side of the bridge would have a DHCP server so that I could simply hook it up to a switch and I'd be on my way. However that isn't the case which leads me to believe I'll have to add one to LAN2 correct? Or is there some way to have the DHCP from LAN1 also hand out IP addresses to LAN2? If I do need a DHCP device on LAN2 what would be best? Another hardware device or should I just install some DHCP software on one of the systems (since they're both on 24/7 anyway). Any recommendations would be appreciated. :)

  Read the article

• Acer Aspire one is falling apart on Ubuntu

  - by Narcolapser

  Question: How do I have my netbook detect and install hardware? Info: I have an Acer Aspire One, it came with windows XP and I loaded it with Win7. I decided I wanted to change to Ubuntu so I tried Ubuntu netbook remix, which failed horribly, and so after attempting 3 or so other OS's I ended with Ubuntu Desktop 9.10. Which worked fine for a while, but there were some minor issues so I asked a question about it here and decided to change my OS again. This last weekend I tried mandriva like that guy in my other question suggested, no success. when I had though my netbook lost the ability to use it's touch pad, I didn't think much of it, just thought it must be a driver or something. But When Mandriva failed, and I also while I was at it tried Damn small linux and Debian, which both failed to, I decided to switch back to Ubuntu Desktop(some where in here my keyboard stopped working for one attempt to). But first I gave the netbook remix one more try. it worked this time, with the exception of it didn't have any networking. I thought it was a driver issue again and finished the weekend with ubuntu desktop 9.10 again. But now things get really crazy. it doesn't know it has a wireless card or an ethernet card. It doesn't know my phone is connected trying to provide wireless broadband either. I'm clueless on what could be the problem. And with only a minimal amount of experience with Ubuntu can't navigate the entire interface with only my keyboard(it doesn't detect a USB mouse when I plug it in, it had when I installed it. in fact the network interfaces were working just fine when I live boot ubuntu to installed it). Even so, I don't know where to go or what to do to make it recognize it's hardware. I'm in a dire situation, any help is welcome.

  Read the article

• Windows won't sleep after booting from grub

  - by mkasberg

  I recently added a second hard drive to my computer and I am using it do dual-boot Linux (Ubuntu 12.04) with Windows 7. Both hard drives are SATA. I am using the default grub bootloader on my second hard drive. The windows drive is unmodified. To get to grub, I changed the hard disk boot priority in my BIOS (P35-DS3L) to boot from the second drive. The problem I'm having is that when I boot to Windows 7 (on sda) from grub (on sdb), Windows 7 will not go to sleep (from the start menu). The display shuts off momentarily as if its going to sleep, then comes back on and displays the switch-user screen. Powercfg -lastwake does not show anything. I am sure that this is related to booting from grub on sdb because when I change the hard disk boot priority in the BIOS to boot from my (unmodified) Windows hard disk, the computer goes to sleep fine. It occurred to me that installing grub on sda might solve the problem, but I'd rather not since I like to have my windows hard disk unmodified so that booting to it from the BIOS boots directly to windows. A possible work around is to use the BIOS as a bootloader, by pressing F8 to select the boot device. Still, I'd like to know why the problem is happening in the first place.

  Read the article

< Previous Page | 470 471 472 473 474 475 476 477 478 479 480 481  | Next Page >