Search Results

Search found 13104 results on 525 pages for 'malcolm box'.

Page 477/525 | < Previous Page | 473 474 475 476 477 478 479 480 481 482 483 484  | Next Page >

• Why apcupsd won't see the UPS connected to the USB posrt on FreeBSD 8.0 amd64

  - by Max Kosyakov

  Hello, Recently I installed an apcusbd on a FreeBSD 8.0 amd64 box via ports system. It installed perfectly but it won't run. Here what is says in the log: FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device It appeared that HID driver picked the /dev/ugen4.2 which could cause the apcusb being unable to find the device. After I had discovered this, I rebuilt the kernel and removed the hid driver. Now it just shows "ugen4.2: <Tripp Lite> at usbus4" and no uhid0 device appears. Nevertheless the problem persisted. I tried to leave the DEVICE config setting blank --- won't help. Then I specified the particular device in the config, but it did not help either. Below you is the output of several commands that can provide some useful information on my case. server# /usr/local/etc/rc.d/apcupsd start Starting apcupsd. server# tail /var/log/messages | grep apcupsd Jun 17 22:30:00 server apcupsd[1520]: apcupsd FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device -- For a link to detailed USB trouble shooting information, please see . Jun 17 22:30:00 server apcupsd[1520]: apcupsd error shutdown completed server# cat /usr/local/etc/apcupsd/apcupsd.conf ## apcupsd.conf v1.1 ## UPSCABLE usb UPSTYPE usb DEVICE /dev/ugen4.2 LOCKFILE /var/lock UPSCLASS standalone UPSMODE disable server# dmesg | grep '^u' uhci0: port 0xa800-0xa81f irq 16 at device 26.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x0f00 usbus0: on uhci0 uhci1: port 0xa880-0xa89f irq 21 at device 26.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x0f00 usbus1: on uhci1 uhci2: port 0xac00-0xac1f irq 18 at device 26.2 on pci0 uhci2: [ITHREAD] uhci2: LegSup = 0x0f00 usbus2: on uhci2 usbus3: EHCI version 1.0 usbus3: on ehci0 uhci3: port 0xa080-0xa09f irq 23 at device 29.0 on pci0 uhci3: [ITHREAD] uhci3: LegSup = 0x0f00 usbus4: on uhci3 uhci4: port 0xa400-0xa41f irq 19 at device 29.1 on pci0 uhci4: [ITHREAD] uhci4: LegSup = 0x0f00 usbus5: on uhci4 uhci5: port 0xa480-0xa49f irq 18 at device 29.2 on pci0 uhci5: [ITHREAD] uhci5: LegSup = 0x0f00 usbus6: on uhci5 usbus7: EHCI version 1.0 usbus7: on ehci1 uart0: port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 12Mbps Full Speed USB v1.0 usbus6: 12Mbps Full Speed USB v1.0 usbus7: 480Mbps High Speed USB v2.0 ugen0.1: at usbus0 uhub0: on usbus0 ugen1.1: at usbus1 uhub1: on usbus1 ugen2.1: at usbus2 uhub2: on usbus2 ugen3.1: at usbus3 uhub3: on usbus3 ugen4.1: at usbus4 uhub4: on usbus4 ugen5.1: at usbus5 uhub5: on usbus5 ugen6.1: at usbus6 uhub6: on usbus6 ugen7.1: at usbus7 uhub7: on usbus7 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub4: 2 ports with 2 removable, self powered uhub5: 2 ports with 2 removable, self powered uhub6: 2 ports with 2 removable, self powered uhub3: 6 ports with 6 removable, self powered uhub7: 6 ports with 6 removable, self powered ugen4.2: at usbus4 server#

  Read the article

• PCI-DSS compliance for business with only swipe terminals [migrated]

  - by rowatt

  I support the IT infrastructure for a small retail business which is now required to undergo a PCI-DSS assessment. The payment service and terminal provider (Streamline) has asked that we use Trustwave to do the PCI-DSS certification. The problem I face is that if I answer all questions and follow Trustwave's requirements to the letter, we will have to invest significantly in networking equipment to segment LANs and /or do internal vulnerability scanning, while at the same time Streamline assures me that the terminals we have (Verifone VX670-B and MagIC3 X-8) are secure, don't store any credit card information and are PCI-DSS compliant so by implication we don't need to take any action to ensure their network security. I'm looking for any suggestions as to how we can most easily meet the networking requirements for PCI-DSS. Some background on our current network setup: single wired LAN, also with WiFi turned on (though if this creates any PCI-DSS complexities we can turn it off). single Netgear ADSL router. This is the only firewall we have in place, and the firewall is out the box configuration (i.e. no DMZ, SNMP etc). Passwords have been changed though :-) a few windows PCs and 2 windows based tills, none of which ever see any credit card information at all. two swipe terminals. Until a few months ago (before we were told we had to be PCI-DSS certified) these terminals did auth/capture over the phone. Streamline suggested we moved to their IP Broadband service, which instead uses an SSL encrypted channel over the internet to do auth/capture, so we now use that service. We don't do any ecommerce or receive payments over the internet. All transactions are either cardholder present, or MOTO with details given over phone and typed direct into terminal. We're based in the UK. As I currently understand it we have three options in order to get PCI-DSS certification. segment our network so the POS terminals are isolated from all PCs, and set up internal vulnerability scanning on that network. don't segment the network, and have to do more internal scanning and have more onerous management of PCs than I think we need (for example, though the tills are Windows based, they are fully managed so I have no control over software update policies, anti virus etc). All PCs have anti virus (MSE) and windows updates automatically applied, but we don't have any centralised go back to auth/capture over phone lines. I can't imagine we are the first merchant to be in this situation. I'm looking for any recommendations a simple, cost effective way to be PCI-DSS compliant - either by doing 1 or 2 above with (hopefully) simple and inexpensive equipment/software, or any other ways if there's a better way to do this. Or... should we just go back to the digital stone age and do auth/capture over the phone, which means we don't need to do anything on our network to be PCI-DSS certified?

  Read the article

• ssh refuses to authenticate keys

  - by MixturaDementiae

  So I am setting up a connection between my machine [fedora 17] and a virtual machine running in Virtual Box in which is running CentOS 5. I have installed openssh from the repositories on CentOS, and I have configured everything as it follows: Protocol 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key SyslogFacility AUTHPRIV PermitRootLogin yes RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile /home/pigreco/.ssh/authorized_keys PasswordAuthentication no ChallengeResponseAuthentication yes GSSAPIAuthentication yes GSSAPICleanupCredentials yes UsePAM yes AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL LANGUAGE AcceptEnv XMODIFIERS X11Forwarding yes Subsystem sftp /usr/libexec/openssh/sftp-server this is the configuration file sshd_config on the server i.e. on the CentOS. Moreover I have created a public/private key pair as usual on the .ssh/ folder in my home directory in my OS, i.e. Fedora, and then I've copied with scp the id_rsa.pub to the server and then I have appended its content to the file .ssh/authorized_keys on the server machine. The error that I get is the following: OpenSSH_5.9p1, OpenSSL 1.0.0j-fips 10 May 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 50: Applying options for * debug1: Connecting to 192.168.100.13 [192.168.100.13] port 22. debug1: Connection established. debug1: identity file /home/mayhem/.ssh/identity type -1 debug1: identity file /home/mayhem/.ssh/identity-cert type -1 debug1: identity file /home/mayhem/.ssh/id_rsa type 1 debug1: identity file /home/mayhem/.ssh/id_rsa-cert type -1 debug1: identity file /home/mayhem/.ssh/id_dsa type -1 debug1: identity file /home/mayhem/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 16:e5:72:d1:37:94:1b:5e:3d:3a:e5:da:6f:df:0c:08 debug1: Host '192.168.100.13' is known and matches the RSA host key. debug1: Found key in /home/mayhem/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,keyboard-interactive debug1: Next authentication method: gssapi-keyex debug1: No valid Key exchange context debug1: Next authentication method: gssapi-with-mic debug1: Unspecified GSS failure. Minor code may provide more information Cannot determine realm for numeric host address debug1: Unspecified GSS failure. Minor code may provide more information Cannot determine realm for numeric host address debug1: Unspecified GSS failure. Minor code may provide more information debug1: Unspecified GSS failure. Minor code may provide more information Cannot determine realm for numeric host address debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/mayhem/.ssh/id_rsa debug1: Server accepts key: pkalg ssh-rsa blen 279 Agent admitted failure to sign using the key. debug1: Trying private key: /home/mayhem/.ssh/identity debug1: Trying private key: /home/mayhem/.ssh/id_dsa debug1: Next authentication method: keyboard-interactive Do you have some good suggestion of what I can do? thank you

  Read the article

• Ubuntu with KVM guest VM and broken bridges

  - by MadPsy

  I have an Ubuntu box with a KVM guest VM running. They use bridging so the guest VM attaches to the physical network of its host. The guest VM has 2 NICs in 2 different bridges. First NIC of the VM is tap5 and is in bridge br0 br0 8000.46720f5c572e no eth0.500 tap5 Second NIC of the VM is tap2 and is in bridge br100 br100 8000.76ad2fc96661 no eth0.100 eth0.101 eth0.103 eth0.104 eth0.105 tap2 On the host, br0 has an IP and br100 does not 21: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 46:72:0f:5c:57:2e brd ff:ff:ff:ff:ff:ff inet 192.168.100.4/24 brd 192.168.10.255 scope global br0 inet6 fe80::d6ae:52ff:febe:777/64 scope link valid_lft forever preferred_lft forever On the guest, its eth0 and eth1 interfaces both have IP addresses 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:3e:61:fb:7a:da brd ff:ff:ff:ff:ff:ff inet 192.168.100.6/24 brd 192.168.100.255 scope global eth0 inet6 fe80::23e:61ff:fefb:7ada/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:3e:61:fb:7a:ea brd ff:ff:ff:ff:ff:ff inet 172.16.50.129/25 brd 172.16.50.255 scope global eth1 inet6 fe80::23e:61ff:fefb:7aea/64 scope link valid_lft forever preferred_lft forever On the guest VM, a tcpdump of its eth1 interface (tap2) shows traffic from its eth0 interface (tap5), as if the 2 bridges are themselves bridged. This means any interface on br100 is now bridged across to br0 - which is completely broken. root@chillispot:~# tcpdump -c 1 -n -v -i eth1 net 192.168.100.0/24 tcpdump: listening on eth1, link-type EN10MB (Ethernet), capture size 65535 bytes 16:31:24.175583 IP (tos 0x0, ttl 64, id 48054, offset 0, flags [DF], proto TCP (6), length 148) 192.168.100.6.22 > 192.168.100.4.59505: Flags [P.], cksum 0x6c2b (correct), seq 1056321648:1056321744, ack 398642983, win 1700, options [nop,nop,TS val 197473436 ecr 200655363], length 96 What could be bridging the 2 bridges, except the guest VM (which is a stock Ubuntu install)? I am at a complete loss! Thanks.

  Read the article

• server 2008 r2 - wbadmin systemstatebackup - system writer not found in the backup

  - by TWood

  I am trying to manually run a systemstatebackup command on my server 2008 r2 box and I am getting an error code '2155347997' when I view the backup event log details. The command line tells me that I have log files written to the c:\windows\logs\windowsserverbackup\ path but I have no files of the .log type there. My command window tells me "System Writer is not found in the backup". However when I run vssadmin list writers I find System Writer in the list and it shows normal status with no last errors stored. I am running this from an elevated command prompt as well as from a logged on administrator account. My backup target path has permission for network service to have full control and it has plenty of free space. Looking in eventlog I have two VSS error 8194 that happen immediately before the Backup error 517 which has the errorcode 2155347997 listed. All three of these errors are a result of trying to run the command for the systemstatebackup. It's my belief that some VSS related permission is failing and exiting the backup process before it ever gets started. Because of this the initial code that creates the log files must not be running and this is why I have no files. When running the systemstatebackup command from the command prompt and watching the windowsserverbackup directory I do see that I have a Wbadmin.0.etl file which gets created but it is deleted when the backup errors out and stops. I have looked online and there are numerous opinions as to the cause of this error. These are the things I have corrected to try and fix this issue before posting here: Machine runs a HP 1410i smart array controller but at one time also used a LSI scsi card. Used networkadminkb.com's kb# a467 to find one LSI_SCSI entry in HKLMSysCurrentControlSetServices which start was set to 0x0 and I modified to 0x3. No changes. In HKLMSystemCurrentControlSetServicesVSSDiag I gave network service full control where it previously only had "Special Permission". No changes. I followed KB2009272 to manually try to fix system writer. These are all of the things I have tried. What else should I look at to resolve this issue? It may be important to note that I run Mozy Pro on this server and that was known in the past to use VSS for copying operations and it occasionally threw an error. However since an update last year those error event log entries have stopped.

  Read the article

• Outlook refuses to connect to Exchange

  - by wfaulk

  Outlook 2007 under Windows XP connecting to Exchange 2003 SP2: when started, it flips back and forth between "Connecting to Exchange Server" and "Disconnected" three or four times, then gives up and stays disconnected. I tried deleting the ost file (which was nearly 2GB), turning Cached mode on and off, recreating the account inside the Mail control panel, changing the account to use HTTP, and probably some other things. None of it seemed to make any difference, until … After fiddling with it for a while, I got this absurd error message dialog at startup, and it exits after I click OK: Cannot start Microsoft Office Outlook. Cannot open the Outlook window. The set of folders cannot be opened. Microsoft Exchange is not available. Either there are network problems or the Exchange server is down for maintenance. (I'm not sure if I can even trust that message. It's so long, it just feels like a random offset into Outlook's stack of error messages.) Either way, the Exchange server is available to everyone else, and is available via OWA from that computer. I ran Process Explorer against Outlook and it showed 5 or so ESTABLISHED connections to our Exchange server, plus listening on two UDP ports, and two CLOSE_WAIT connections to localhost. If I managed to look at Outlook's IP connections while it was doing its Connecting/Disconnected dance, it had a huge number of connections open to the Exchange server. It more than filled ProcExp's dialog box; I'm guessing at least 20, probably more. The only other odd thing is that our network admin at some point added a wildcard DNS record to the domain name that we use for email, and now Outlook will sometimes (always?) start by complaining about autodiscover.example.com's SSL certificate. There is a web server there, but it doesn't have any sort of email autodiscover anything on it. It doesn't make any difference if I click "OK" or "Cancel" (or whatever the buttons are). I also added a bogus entry for the hostname to Windows' hosts file, pointing it at 127.0.0.2, and it stopped complaining about the certificate. (The CLOSE_WAIT sockets above were from before I made this change, and went away after.) I don't think this is related, as the same problem should exist for everyone, but it might be. This is the second time this user has had this problem. The first time, I never found a solution other than reinstalling Outlook. Now that it's a pattern, I'd like to find a permanent solution, rather than assume it's a random glitch.

  Read the article

• opening adobe reader results in infinite explorer.exe process creation loop

  - by irrational John

  First, apologies if the answer to this is only a Google away. I tried, honest I did. But I wasn't able to find anything about this problem posted elsewhere. I'm using Adobe Reader v9.3.2 in Windows 7 Home Premium 64-bit. If you want more system details, then just request them. What happens is that when I attempt to open a PDF by clicking "Open" on it then (1) adobe reader never opens and (2) the explorer.exe program is (apparently) recursively opened. I base this on opening the Task Manager and seeing a long list of explorer.exe processes under the "Processes" tab. Usually there is only one. When I recreate this problem, the list of explorer.exe processes are at least a page or two long. (Too many to bother counting). I "correct" this problem by logging off and then logging back on. This kills all the explorer.exe tasks. Unfortunately I don't know another way to terminate them all. Now here's the curious part. This only happens when I attempt to "Open" a PDF file. If instead I use the context menu (right mouse click on the PDF) and select "Open with" and "Adobe Reader 9.3" then Adobe Reader opens the file with no problem. It seems that there is something wrong with the setting for the default open action for PDF files. However, I have been unable to fix this by changing the Windows setting. Here is what I have tried. When I open Control Panel > All Control Panel Items > Default Programs > Set Associations I do not find an entry for file type .pdf. There are only entries for .pdfxml and .pdx. When use "Open with" on a PDF file and select "Choose default program", the check box for "Always use the selected program to open this kind of file" is disabled (greyed out). I have uninstalled and reinstalled Adobe Reader but the problem persists. While obviously no lives are at stake here, this problem is annoying the frickin' heck out of me. If I forget and recreate this bug then I have to stop everything I'm doing to stop it. Any suggestions on how I might go about fixing this?

  Read the article

• How to get more information from the system crash

  - by viraptor

  I'd like to debug an issue I'm having with a linux (debian stable) server, but I'm running out of ideas of how to confirm any diagnosis. Some background: The servers are running DL160 class with hardware raid between two disks. They're running a lot of services, mostly utilising network interface and CPU. There are 8 cpus and 7 "main" most cpu-hungry processes are bound to one core each via cpu affinity. Other random background scripts are not forced anywhere. The filesystem is writing ~1.5k blocks/s the whole time (goes up above 2k/s in peak times). Normal CPU usage for those servers is ~60% on 7 cores and some minimal usage on the last (whatever's running on shells usually). What actually happens is that the "main" services start using 100% CPU at some point, mainly stuck in kernel time. After a couple of seconds, LA goes over 400 and we lose any way to connect to the box (KVM is on it's way, but not there yet). Sometimes we see a kernel reporting hung task (but not always): [118951.272884] INFO: task zsh:15911 blocked for more than 120 seconds. [118951.272955] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [118951.273037] zsh D 0000000000000000 0 15911 1 [118951.273093] ffff8101898c3c48 0000000000000046 0000000000000000 ffffffffa0155e0a [118951.273183] ffff8101a753a080 ffff81021f1c5570 ffff8101a753a308 000000051f0fd740 [118951.273274] 0000000000000246 0000000000000000 00000000ffffffbd 0000000000000001 [118951.273335] Call Trace: [118951.273424] [<ffffffffa0155e0a>] :ext3:__ext3_journal_dirty_metadata+0x1e/0x46 [118951.273510] [<ffffffff804294f6>] schedule_timeout+0x1e/0xad [118951.273563] [<ffffffff8027577c>] __pagevec_free+0x21/0x2e [118951.273613] [<ffffffff80428b0b>] wait_for_common+0xcf/0x13a [118951.273692] [<ffffffff8022c168>] default_wake_function+0x0/0xe .... This would point at raid / disk failure, however sometimes the tasks are hung on kernel's gettsc which would indicate some general weird hardware behaviour. It's also running mysql (almost read-only, 99% cache hit), which seems to spawn a lot more threads during the system problems. During the day it does ~200kq/s (selects) and ~10q/s (writes). The host is never running out of memory or swapping, no oom reports are spotted. We've got many boxes with similar/same hardware and they all seem to behave that way, but I'm not sure which part fails, so it's probably not a good idea to just grab something more powerful and hope the problem goes away. Applications themselves don't really report anything wrong when they're running. I can run anything safely on the same hardware in an isolated environment. What can I do to narrow down the problem? Where else should I look for explanation?

  Read the article

• Has anyone achieved true differential sync with rsync in ESXi?

  - by Julius

  Berate me later on the fact that I'm using the service console to do anything in ESXi... I've got a working rsync binary (v3.0.4) that I can use in ESXi 4.1U1. I tend to use rsync over cp when copying VM's or backups from one local datastore to another local datastore. I've used rsync to copy data from one ESXi box to another but that was just for small files. In now trying to do true differential syncs of backups taken via ghettoVCB between my primary ESXi machine and a secondary one. But even when I do this locally (one datastore to another datastore on the same ESXi machine) rsync appears to copy the files in their entirety. I've got two VMDK's totally 80GB in size, and rsync still takes anywhere between 1 and 2 hours but the VMDK's aren't growing that much daily. Below is the rsync command I'm executing. I am copying locally because ultimately these files will get copied onto a datastore created from a LUN on a remote system. Its not an rsync that'll be serviced by an rsync daemon on a remote system. rsync -avPSI VMBACKUP_2011-06-10_02-27-56/* VMBACKUP_2011-06-01_06-37-11/ --stats --itemize-changes --existing --modify-window=2 --no-whole-file sending incremental file list >f..t...... VM-flat.vmdk 42949672960 100% 15.06MB/s 0:45:20 (xfer#1, to-check=5/6) >f..t...... VM.vmdk 556 100% 4.24kB/s 0:00:00 (xfer#2, to-check=4/6) >f..t...... VM.vmx 3327 100% 25.19kB/s 0:00:00 (xfer#3, to-check=3/6) >f..t...... VM_1-flat.vmdk 42949672960 100% 12.19MB/s 0:56:01 (xfer#4, to-check=2/6) >f..t...... VM_1.vmdk 558 100% 2.51kB/s 0:00:00 (xfer#5, to-check=1/6) >f..t...... STATUS.ok 30 100% 0.02kB/s 0:00:01 (xfer#6, to-check=0/6) Number of files: 6 Number of files transferred: 6 Total file size: 85899350391 bytes Total transferred file size: 85899350391 bytes Literal data: 2429682778 bytes Matched data: 83469667613 bytes File list size: 129 File list generation time: 0.001 seconds File list transfer time: 0.000 seconds Total bytes sent: 2432530094 Total bytes received: 5243054 sent 2432530094 bytes received 5243054 bytes 295648.92 bytes/sec total size is 85899350391 speedup is 35.24 Is this because ESXi is itself making so many changes to the VMDK's that as far as rsync is concerned the entire file has to be retransmitted? Has anyone actually achieved actual diff sync with ESXi?

  Read the article

• PPTP VPN Not Working - Peer failed CHAP authentication, PTY read or GRE write failed

  - by armani

  Brand-new install of CentOS 6.3. Followed this guide: http://www.members.optushome.com.au/~wskwok/poptop_ads_howto_1.htm And I got PPTPd running [v1.3.4]. I got the VPN to authenticate users against our Active Directory using winbind, smb, etc. All my tests to see if I'm still authenticated to the AD server pass ["kinit -V [email protected]", "smbclient", "wbinfo -t"]. VPN users were able to connect for like . . . an hour. I tried connecting from my Android phone using domain credentials and saw that I got an IP allocated for internal VPN users [which I've since changed the range, but even setting it back to the initial doesn't work]. Ever since then, no matter what settings I try, I pretty much consistently get this in my /var/log/messages [and the VPN client fails]: [root@vpn2 ~]# tail /var/log/messages Aug 31 15:57:22 vpn2 pppd[18386]: pppd 2.4.5 started by root, uid 0 Aug 31 15:57:22 vpn2 pppd[18386]: Using interface ppp0 Aug 31 15:57:22 vpn2 pppd[18386]: Connect: ppp0 <--> /dev/pts/1 Aug 31 15:57:22 vpn2 pptpd[18385]: GRE: Bad checksum from pppd. Aug 31 15:57:24 vpn2 pppd[18386]: Peer armaniadm failed CHAP authentication Aug 31 15:57:24 vpn2 pppd[18386]: Connection terminated. Aug 31 15:57:24 vpn2 pppd[18386]: Exit. Aug 31 15:57:24 vpn2 pptpd[18385]: GRE: read(fd=6,buffer=8059660,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Aug 31 15:57:24 vpn2 pptpd[18385]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Aug 31 15:57:24 vpn2 pptpd[18385]: CTRL: Client 208.54.86.242 control connection finished Now before you go blaming the firewall [all other forum posts I find seem to go there], this VPN server is on our DMZ network. We're using a Juniper SSG-5 Gateway, and I've assigned a WAN IP to the VPN box itself, zoned into the DMZ zone. Then, I have full "Any IP / Any Protocol" open traffic rules between DMZ<--Untrust Zone, and DMZ<--Trust Zone. I'll limit this later to just the authenticating traffic it needs, but for now I think we can rule out the firewall blocking anything. Here's my /etc/pptpd.conf [omitting comments]: option /etc/ppp/options.pptpd logwtmp localip [EXTERNAL_IP_ADDRESS] remoteip [ANOTHER_EXTERNAL_IP_ADDRESS, AND HAVE TRIED AN ARBITRARY GROUP LIKE 5.5.0.0-100] Here's my /etc/ppp/options.pptpd.conf [omitting comments]: name pptpd refuse-pap refuse-chap refuse-mschap require-mschap-v2 require-mppe-128 ms-dns 192.168.200.42 # This is our internal domain controller ms-wins 192.168.200.42 proxyarp lock nobsdcomp novj novjccomp nologfd auth nodefaultroute plugin winbind.so ntlm_auth-helper "/usr/bin/ntlm_auth --helper-protocol=ntlm-server-1" Any help is GREATLY appreciated. I can give you any more info you need to know, and it's a new test server, so I can perform any tests/reboots required to get it up and going. Thanks a ton.

  Read the article

• How can I force all internet traffic over a PPTP VPN but still allow local lan access?

  - by user126715

  I have a server running Linux Mint 12 that I want to keep connected to a PPTP VPN all the time. The VPN server is pretty reliable, but it drops on occasion so I just want to make it so all internet activity is disabled if the VPN connection is broken. I'd also like to figure out a way to restart it automatically, but that's not as big of an issue since this happens pretty rarely. I also want to always be able to connect to the box from my lan, regardless of whether the VPN is up or not. Here's what my ifconfig looks like with the VPN connected properly: eth0 Link encap:Ethernet HWaddr 00:22:15:21:59:9a inet addr:192.168.0.171 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::222:15ff:fe21:599a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:37389 errors:0 dropped:0 overruns:0 frame:0 TX packets:29028 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:37781384 (37.7 MB) TX bytes:19281394 (19.2 MB) Interrupt:41 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1446 errors:0 dropped:0 overruns:0 frame:0 TX packets:1446 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:472178 (472.1 KB) TX bytes:472178 (472.1 KB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.10.11.10 P-t-P:10.10.11.9 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:23 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:1368 (1.3 KB) TX bytes:1812 (1.8 KB) Here's an iptables script I found elsewhere that seemed to be for the problem I'm trying to solve, but it wound up blocking all access, but I'm not sure what I need to change: #!/bin/bash #Set variables IPT=/sbin/iptables VPN=`ifconfig|perl -nE'/dr:(\S+)/&&say$1'|grep 10.` LAN=192.168.0.0/24 #Flush rules $IPT -F $IPT -X #Default policies and define chains $IPT -P OUTPUT DROP $IPT -P INPUT DROP $IPT -P FORWARD DROP #Allow input from LAN and tun0 ONLY $IPT -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT $IPT -A INPUT -i lo -j ACCEPT $IPT -A INPUT -i tun0 -m conntrack --ctstate NEW -j ACCEPT $IPT -A INPUT -s $LAN -m conntrack --ctstate NEW -j ACCEPT $IPT -A INPUT -j DROP #Allow output from lo and tun0 ONLY $IPT -A OUTPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT $IPT -A OUTPUT -o lo -j ACCEPT $IPT -A OUTPUT -o tun0 -m conntrack --ctstate NEW -j ACCEPT $IPT -A OUTPUT -d $VPN -m conntrack --ctstate NEW -j ACCEPT $IPT -A OUTPUT -j DROP exit 0 Thanks for your help.

  Read the article

• Cygwin's RSYNC for large data transfer

  - by Tim Brigham

  I'm using rsync from Cygwin to do a large scale data transfer from an aging HP MSA 1000 to a new DAS attached to a different server. I have a daemon running on the remote server in read only mode and a local copy writing the files to disk. One of my servers is an image repository with over a million files spread across about 300 directories. Each file averages only a couple hundred kilobytes. More so than any other box this one is proving problematic. The rsync process will work for a while - some times 20 minutes, some times an hour - and then it simply quits and sits idle at a given file name. I have verified that the file isn't corrupt on the remote server and that the file is successfully created on the local drive. I ran the rsync client in -vv mode, which returns nothing. I checked out the logs created by the daemon. I looked at the network utilization on the interface, which is sitting idle. I looked at the AV settings to see if anything could pose a problem there. I even updated to the latest release of Cygwin. What do I need to in order to keep this connection up? EDIT: The client system is using the command rsync.exe server::Drives/f/Repo/ /cygdrive/T/Repo --archive -P -vv The server is using the command rsync.exe --daemon --no-detach --config "rsyncd.conf" The contents of rsyncd.conf: use chroot = false strict modes = false hosts allow = 192.168.100.9 log file = c:/rsyncd.log uid=0 gid=0 [Drives] path = /cygdrive read only = yes EDIT: The file server is 2003, the disk type on the array is GPT and the size is of the array is about 4 TB. EDIT: Stranger.. It looks like the process is reliably erroring out at about 175,000 files. Rsync runs fine when I pick the same directory it has problems with one at a time. EDIT: rsync version 3.0.9 protocol version 30 Copyright (C) 1996-2011 by Andrew Tridgell, Wayne Davison, and others. Web site: http://rsync.samba.org/ Capabilities: 64-bit files, 64-bit inums, 32-bit timestamps, 64-bit long ints, no socketpairs, hardlinks, symlinks, IPv6, batchfiles, inplace, append, ACLs, xattrs, iconv, symtimes A similar failure occurred when going from the same set of files with Cygwin to a Linux install. It didn't happen until several hours later than normal however.

  Read the article

• Plesk Postfix Mail Server 9.5.4 very heavy load, 1000s of processes

  - by Eugene van der Merwe

  Our Plesk Linux Ubuntu 64-bit mail server has extremely high load and we don't know how to isolate it. The load was okay will two weeks ago but in the last two weeks it's seriously deteriorated. The mail server has been running for years and we have had sporadic performance issues. Normally we reduce the load by turning off all SPAM checks until the problem is sorted (which sometimes resolves itself). Currently we have turned of real time block lists, SPF checking and we have attempted to turn off SpamAssassin. No matter what we do the SpamAssassin check box stays ticked in the GUI. Out of desperation we have done /etc/init.d/psa-spamassassin stop. For years we haven't been able to do SpamAssassin because it kills the server. We would like to use it but performance is more important for now. We cannot turn off Greylisting. The moment we turn off Greylisting our help desk is inandated with calls. Out of desperation we investigated truncating the Greylisting database which is now 2.5 GB big but we abandoned this after noticing turning of Greylisting doesn't improve the performance at all. We have no anti-virus. It's just more load and Dr. Web never really worked that well for us. But we'll try that if it will make a difference. We have implemented Postfix Anvil. This seems to have made the situation worse so we disabled it. We’re not sure if this is the case. Our current mail server is configured to forward all SMTP to a relay server. We did so to reduce the load. This helped a lot because outgoing queues are generally empty. We are running in an Expand configuration. The mail server has about 12 000 accounts of which maybe half are active. We have read through this document: http://www.postfix.org/STRESS_README.html but there are too many settings and we don’t know which ones to choose. Please assist urgently. We need advice on how to fix this problem before all our clients abandon is. The only clue we have is that there are 100s of these processes: 30 13205 1 0 13:18 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10027 before-queue 30 13207 1 0 11:38 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10027 before-queue 30 13208 1 0 13:18 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10026 before-remote 30 13209 1 0 11:38 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10026 before-remote 30 13213 1 0 13:18 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10027 before-queue

  Read the article

• Windows Service Limit Crashes Services on Startup

  - by Paul Williams

  We have developed a custom Windows service in C# as part of a large Enterprise application. Our QA department tests multiple versions of this service. The QA lab has several (over 20) copies of this service installed on one Windows 2003 test box. Each copy is in its own folder and has a unique service name, though each executable file is named the same (OurWindowsService.exe, for example). Each service uses the same Windows credentials (a domain user). The purpose of this service is to handle MSMQ messages. The queued messages do all sorts of important stuff. For some reason, they can run only 5 of these services at a time. When we start a 6th, the service crashes on startup. For example, I can start #1, #2, #3, #4, and #5. When I start #6, it crashes. However, if I stop #1 and start #6, #6 runs fine, and now #1 fails to start. When the services crash, the following error appears in the Windows event log: Faulting application OurWindowsService.exe, version 5.40.1.1, faulting module kernel32.dll, version 5.2.3790.4480, fault address 0x0000bef7. I was able to use WinDbg to generate a postmortem dump file. The dump file revealed that the crash occurs trying to delay load SHLWAPI.dll: 0:000> kb100 ChildEBP RetAddr Args to Child 0012ece4 79037966 c06d007e 00000000 00000001 KERNEL32!RaiseException+0x53 0012ed4c 790099ba 00000008 0012ed08 7c82860c mscoree!__delayLoadHelper2+0x139 0012ed98 790075b1 001550c8 0012edac 0012fb34 mscoree!_tailMerge_**SHLWAPI_dll**+0xd 0012edb0 79007623 001550c8 0012edf8 0012edf4 mscoree!XMLGetVersionWithSupported+0x22 0012ee00 790069a4 aa06f1b0 00000000 000001fe mscoree!RuntimeRequest::GetRuntimeVersion+0x56 0012f478 790077aa 00000001 7903fb4c 0012fb34 mscoree!RuntimeRequest::ComputeVersionString+0x5bd 0012f89c 79007802 00000001 0012f8b4 7903fb4c mscoree!RuntimeRequest::FindVersionedRuntime+0x11c 0012f8b8 79007b19 00000001 00000000 aa06fa6c mscoree!RuntimeRequest::RequestRuntimeDll+0x2c 0012ffa4 79007c02 00000001 0012ffbc 00000000 mscoree!GetInstallation+0x72 0012ffc0 77e6f23b 00000000 00000000 7ffdf000 mscoree!_CorExeMain+0x12 0012fff0 00000000 79007bf0 00000000 78746341 KERNEL32!BaseProcessStart+0x23 I believe the error code handed to Kernel32.RaiseException, c06d007e, means Module Not Found, but I'm not certain. Does this sound familiar to anyone? Are we hitting some limit on the number of service instances on some file name? Does MSMQ dislike more than 5 listening services?

  Read the article

• Getting an boot error when starting computer

  - by Rob Avery IV

  I was in the middle of watching a movie on Netflix, then suddenly everything started crashing. First, explorer.exe closed down, then Google chrome. I had multiple things running in the background (Steam, Raptr, etc.). Individuality, each of those apps closed down also. When they did, a small dialog box popped up for each of them, one at a time, saying that it was missing a file, it couldn't run anymore, or something similar to that. It also had some jumbled up "code" with numbers and letters that I couldn't read. Ever since then, everytime I turn my computer on, it will run for a few seconds and give this error "Reboot and select proper boot device or insert boot media in selected boot device and press a key_". No matter how many times I try to reboot it, it always gives me the same error. A day later after this happened I was able to start the computer, but before it booted, it told me that I didn't shut down the computer properly and asked how I wanted to run the OS (Run Windows in Safety Mode, Run Windows Normally, etc.). Once I logged, everything went SUPER slow and everything crashed almost instantly. The only thing I opened was Microsoft Security Essentials and only got in about two clicks before it was "Not Responding". Then, after that the whole computer froze and I had to restart it. Now, it's back to saying what it originally said, "Reboot and select proper boot device or insert boot media in selected boot device and press a key_". I built this PC back in February 2012. Here are the specs: OS: Windows 7 Ultimate CPU: AMD 8-core GPU: Nvidia GTX Force 560 Ti RAM: 16GB Hard Drive: Hitachi Deskstar 750GB I'm usually very good taking care of my PC. I don't download anything that's not from a trusted site or source. I don't open up any spam email or such or go to any harmful websites like porn or stream movies. I am very clean with the things I do with my PC and don't do many DIFFERENT things with it. I use it pretty often especially for video games and doing homework in Eclipse. Also, good to note that I don't have any Norton or antisoftware installed. I have Microsoft Security Essentials installed but never did a scan. Thanks!

  Read the article

• Postfix / Dovecot and Email Retrieval

  - by Eric J.

  I have setup Postfix and Dovecot on an Ubuntu box following the instructions http://www.exratione.com/2012/05/a-mailserver-on-ubuntu-1204-postfix-dovecot-mysql/ I can see that email is being delivered to and accepted by the server, but the email is not available for retrieval via POP3. What could be missing in my configuraton? It seems that email is not being properly handed off to Dovecot. Here are what I believe are the relevant /var/log/mail.log entries for an attempt to send email from another domain (hosted by Gmail) to the domain I have setup: Logged during SMTP connection postfix/smtpd[14689]: connect from mail-vb0-f50.google.com[209.85.212.50] postfix/smtpd[14689]: Anonymous TLS connection established from mail-vb0-f50.google.com[209.85.212.50]: TLSv1 with cipher ECDHE-RSA-RC4-SHA (128/128 bits) postfix/smtpd[14689]: 5782740ACF: client=mail-vb0-f50.google.com[209.85.212.50] postfix/cleanup[14696]: 5782740ACF: message-id=<CAEjmKcjHnTY4yk=3QXoNrD76=04g-s9utPguTFB02Fx53GMPmw@mail.gmail.com> postfix/qmgr[14687]: 5782740ACF: from=<[email protected]>, size=1947, nrcpt=1 (queue active) postfix/smtpd[14702]: connect from mail.destinationdomain.com[127.0.0.1] postfix/smtpd[14702]: 2940A41AA9: client=mail.destinationdomain.com[127.0.0.1] postfix/cleanup[14696]: 2940A41AA9: message-id=<CAEjmKcjHnTY4yk=3QXoNrD76=04g-s9utPguTFB02Fx53GMPmw@mail.gmail.com> postfix/qmgr[14687]: 2940A41AA9: from=<[email protected]>, size=2450, nrcpt=1 (queue active) amavis[21309]: (21309-02) Passed CLEAN, [209.85.212.50] <[email protected]> -> <[email protected]>, Message-ID: <CAEjmKcjHnTY4yk=3QXoNrD76=04g-s9utPguTFB02Fx53GMPmw@mail.gmail.com>, mail_id: W52ZB8FAAA+8, Hits: -0.101, size: 1946, queued_as: 2940A41AA9, [email protected], 784 ms postfix/smtpd[14702]: disconnect from mail.destinationdomain.com[127.0.0.1] postfix/smtp[14698]: 5782740ACF: to=<[email protected]>, relay=127.0.0.1[127.0.0.1]:10024, delay=1.1, delays=0.29/0.01/0/0.79, dsn=2.0.0, status=sent (250 2.0.0 from MTA([127.0.0.1]:10025): 250 2.0.0 Ok: queued as 2940A41AA9) postfix/qmgr[14687]: 5782740ACF: removed dovecot: lda([email protected]): msgid=<CAEjmKcjHnTY4yk=3QXoNrD76=04g-s9utPguTFB02Fx53GMPmw@mail.gmail.com>: saved mail to INBOX postfix/pipe[14703]: 2940A41AA9: to=<[email protected]>, relay=dovecot, delay=0.08, delays=0.02/0.02/0/0.04, dsn=2.0.0, status=sent (delivered via dovecot service) postfix/qmgr[14687]: 2940A41AA9: removed Logged during POP3 retrieval attempts dovecot: pop3-login: Login: user=<[email protected]>, method=PLAIN, rip=209.85.220.135, lip=10.195.83.10, mpid=14706 dovecot: pop3([email protected]): Disconnected: Logged out top=0/0, retr=1/2557, del=1/1, size=2540 postfix/smtpd[14689]: disconnect from mail-vb0-f50.google.com[209.85.212.50] dovecot: pop3-login: Login: user=<[email protected]>, method=PLAIN, rip=209.85.212.31, lip=10.195.83.10, mpid=14708 dovecot: pop3([email protected]): Disconnected: Logged out top=0/0, retr=0/0, del=0/0, size=0

  Read the article

• Ping Unknown Host on CentOS at EC2

  - by organicveggie

  Weird problem. We have a collection of servers running CentOS 5 on EC2. The setup includes two DNS servers and two LDAP servers. DNS has a CNAME pointing at the primary LDAP server. One machine (and only one machine) is giving me problems. I can ssh into the server using LDAP authentication. But once I'm on the machine, ping won't resolve the LDAP host even though DNS seems to work fine. Here's ping: $ ping ldap.mycompany.ec2 ping: unknown host ldap.mycompany.ec2 Here's the output of dig: $ dig ldap.mycompany.ec2 ; <<>> DiG 9.3.6-P1-RedHat-9.3.6-4.P1.el5_5.3 <<>> ldap.studyblue.ec2 ;; global options: printcmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 2893 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 2, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;ldap.mycompany.ec2. IN A ;; ANSWER SECTION: ldap.mycompany.ec2. 3600 IN CNAME ec2-hostname.compute-1.amazonaws.com. ec2-hostname.compute-1.amazonaws.com. 55 IN A aaa.bbb.ccc.ddd ;; Query time: 12 msec ;; SERVER: 10.32.159.xxx#53(10.32.159.xxx) ;; WHEN: Tue May 31 11:16:30 2011 ;; MSG SIZE rcvd: 107 And here is resolv.conf: $ cat /etc/resolv.conf search mycompany.ec2 nameserver 10.32.159.xxx nameserver 10.244.19.yyy And here is my hosts file: $ cat /etc/hosts 10.122.15.zzz bamboo4 bamboo4.mycompany.ec2 127.0.0.1 localhost localhost.localdomain And here's nsswitch.conf $ cat /etc/nsswitch.conf passwd: files ldap shadow: files ldap group: files ldap sudoers: ldap files hosts: files dns bootparams: nisplus [NOTFOUND=return] files ethers: files netmasks: files networks: files protocols: files rpc: files services: files netgroup: files ldap publickey: nisplus automount: files ldap aliases: files nisplus So DNS works the way I would expect. And I can ping the ldap server by ip address. And I can even access the box with SSH using LDAP authentication. Any suggestions?

  Read the article

• DLINK WBR-1310B Wireless Router seems to hang...

  - by Ira Baxter

  I have a brand new DLINK-1310B Wireless Router (box never before opened, although I bought it at the neighborhood computer junk store). I am using it at home (and in fact am using it at this instant from a wireless laptop). When operative, I can ping it at 192.168.0.1, and I can log into it from the PC attached to it by LAN and from the wireless PC at //192.168.0.1. In the course of the day since I've installed, it seems to have locked up 3 times. Each time the symptoms are my web browser (or other IP service, e.g., POP3) stops with a "No internet connection" error. Attempts to contact the router via 192.168.0.1 get no reaction, from either the wireless laptop or from the hardwired PC sitting next to it. It doesn't respond to pings to that address either. Power cycling the router fixes it. I've seen discussion in other questions about aging cheap electronics. Its too new to be aged. Anybody else seen this behavior with a DLINK-1310? Or do I just need to exchange it for another and try again? (I hate rolling dice, I bought the DLINK because a previous Linksys died of apparant heating problems, how many do I have to cycle through before I get something that works and is long-term stable?). Remarkably, nobody talks about how much software is in a router. Is the stuff just buggy? EDIT: Happened again, while I was working on the wireless Vista laptop. (Seems like once an hour?) I was a little more careful this time. The wireless laptop can ping it. It can't get the login screen. I visited the LAN-connected PC (takes me a minute to walk from the laptop to the PC at the other end of the house), and attempted to visit a random web page. Surprise, that worked! And, now, after a minute walking back to the laptop, I can reconnect the wireless laptop, and get to the login page from it. Strange the time/date has been reset back to 2002. (I'll swear I set it and saved the system configuration after updating the firmware; it made me redo every other bit of reconfiguration again). Is there something funny about wireless leases expiring? The router says the leases it is handing out are good for 180 minutes, and the delay-to-inaccessible was only about an hour. The DSL connection seems to have a 10 minute lease.

  Read the article

• Firefox: non-Vimperator way to do mouseless browsing?

  - by Peter Mortensen

  Is it possible to do efficient browsing with Firefox using only the keyboard (like in Opera)? By efficient I mean something faster than using TAB - this takes far too long. The arrow keys should be for navigation (in Opera it is Shift + arrow key). It can done with the Vimperator add-on, but isn't there a simpler way? Update 2: the closest to Opera's way is to enable caret navigation (F7 toggles this mode). It doesn't jump between links so it is a little bit slower, but the normal navigation (arrow keys, page up, page down, etc.) works and the focus/caret/cursor follows (in contrast to a text editor for page up/down). And text can be selected and copied like in a text editor. The biggest drawback is that in practice it is necessary to switch in and out of caret mode. And there is no indication of which mode is currently active. Update 1: a work-around (proposed by several but is not really what I am looking for) can be used if 3 settings are changed (to make it practical). After these changes the first few letters of a link text can be typed and that link will selected so pressing Enter will open it. Using the work-around the screen will jump around if it is a long page as it does not restrict itself to the current visible page, but it is usable. First settings change: menu Tools/Options/Advanced/tab General/Accessibility/Search for text when I start typing Turn this option on. Second settings change: set option to only go to links; in address bar enter: about:config followed by Enter. Then: press "I'll be careful, I promise", find the line accessibility.typeaheadfind.linksonly, select it and change the value to True by either hitting Enter or Shift+F10/Toggle (accessibility.typeaheadfind.linksonly is on line 11 when I tried). Third settings change: turn off case-sensitivity. Set accessibility.typeaheadfind.casesensitive to 0 (same procedure as for accessibility.typeaheadfind.linksonly, see above. When Enter is pressed a dialog box will appear with the current value. Type 0 and press Enter). To use: type some part of the link. If there are several possibilities use Ctrl+G (or F3) to jump between them. Use Ctrl+Enter to open in a new tab. Platform: Firefox 3.0.6, Windows XP 64 bit SP2.

  Read the article

• Suggestions for splitting server roles amongst Hyper-V virtual servers / RAID6 or RAID10? / AppAssure

  - by Anon

  We have 2 Hyper-V hosts at present running 1 virtual server that was converted from a physical box running all roles. My plan is to split the roles over various virtual machines, upgrading to the latest software versions as I go, and use the backup server as a standby in case the main server fails. AppAssure backup software has a feature called Virtual Standby, so the VHD's can be ready to be fired up on the backup server if necessary. Off-site backups will be done via external USB drive for now. I'm just seeking some input/suggestions into how I'm planning to split the roles out amongst various virtual servers. Also, I'm curious how to setup the storage on the servers. We do not have any NAS's, SAN'S or any budget for this. What would the best RAID level be to use? I'm thinking either RAID6 (which is currently used) however I'm concerned about the write speeds, or RAID10 but again I'm worried that I can only lose 1 drive (from the same mirror) as opposed to any 2 with RAID6. I realise I have a hot swap for this, but what if a further drive fails during a rebuild? Is the write penalty of RAID6 worth the extra reliability over RAID10? Or will it be too slow with all the roles I am planning, therefore RAID10 is my only real option? The reason for the needed redundancy is I am the only technician and I'm not always on-site. Options I've considered: 1) 5 drives in RAID6 set, 200gb for host OS, rest for VM storage. 1 drive for hot swap - this is how it is currently setup 2) 4 drives in RAID10 set, 200gb for host OS, rest for VM storage. 2 drives for hot swap 3) 4 drives in RAID10 set for VM storage, 2 drives in RAID1 set for host OS. No drives for hot swap - While this is probably the best option with the amount of drives I have, I don't like the idea of having no hot swap 4) 3 drives in RAID6 set for VM storage, 2 drives in RAID1 set for host OS. 1 drive for hot swap All options give us enough storage capacity for our files, etc. We don't have any budget for extra drives or extra hot swap HD chassis for the servers. We have about 70 clients and about 150 users. MAIN SERVER Intel Xeon 5520 @ 2.27 GHz (2 processors) 16GB RAM 6 x 1TB Seagate Barracuda ES.2 Enterprise SATA drives Intel SRCSATAWB RAID controller Virtual machine workload using Hyper-V on Windows Server 2008 R2: DC01 - Active Directory Domain Controller / DNS server / Global catalog - 1GB RAM DC02 - Active Directory Domain Controller / DNS server / Global catalog - 1GB RAM Member Server - DHCP server, File server, Print server - 1GB RAM SCCM Member Server - 4GB RAM Third Party Software Member Server - A/V server, Ticketing software, etc - 4GB RAM Exchange 2007 - 4GB RAM - however we are probably migrating to a hosted solution, therefore freeing up resources BACKUP SERVER Intel Xeon E5410 @ 2.33GHz (2 processors) 16GB RAM 6 x 2TB WD RE4 SATA drives Intel SRCSASRB RAID controller Virtual machine workload using Hyper-V on Windows Server 2008 R2: AppAssure backup software - 8GB RAM

  Read the article

• Add user in CentOS 5

  - by Ron

  I created a new user in my CentOS web server with useradd. Added a password with passwd. But I can't log in with the user via SSH. I keep getting 'access denied'. I checked to make sure that the password was assigned and that the account is active. /var/log/secure shows the following error: Aug 13 03:41:40 server1 su: pam_unix(su:auth): authentication failure; logname= uid=500 euid=0 tty=pts/0 ruser=rwade rhost= user=root Please help, Thanks Thanks for the responses so far: I should add that it is a VPS on a remote computer, fresh out of the box. I can log in as the root user quite fine. I can also su to the new user, but I cannot log in as the new user. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• Localhost has just stopped working (using xampp)

  - by Joe Taylor

  I installed Xampp to use for local development of a Drupal site. Its been working fine out of the box until now. The main Xampp localhost welcome menu loads, however my subdirectory (localhost/drupal) doesn't. It just spins in the browser for ages and nothing happens. Just a blank screen. I've tried the edit people suggest in the hosts file but that hasn't work and I'm getting no errors so not sure what to do. Anyone have any ideas what might be wrong? PS I'm running Windows 7 edit: Log files: Fatal error: Allowed memory size of 134217728 bytes exhausted (tried to allocate 123731968 bytes) in C:\xampp\apps\drupal\htdocs\sites\all\themes\directory\node--job.tpl.php on line 41 Fatal error: Allowed memory size of 134217728 bytes exhausted (tried to allocate 123731968 bytes) in C:\xampp\apps\drupal\htdocs\sites\all\themes\directory\node--job.tpl.php on line 41 [Tue Nov 05 20:52:07.242454 2013] [ssl:warn] [pid 8432:tid 260] AH01909: RSA certificate configured for www.example.com:443 does NOT include an ID which matches the server name [Tue Nov 05 20:52:07.331459 2013] [core:warn] [pid 8432:tid 260] AH00098: pid file C:/xampp/apache/logs/httpd.pid overwritten -- Unclean shutdown of previous Apache run? [Tue Nov 05 20:52:07.820487 2013] [ssl:warn] [pid 8432:tid 260] AH01909: RSA certificate configured for www.example.com:443 does NOT include an ID which matches the server name [Tue Nov 05 20:52:07.898492 2013] [mpm_winnt:notice] [pid 8432:tid 260] AH00455: Apache/2.4.4 (Win32) OpenSSL/0.9.8y PHP/5.4.16 configured -- resuming normal operations [Tue Nov 05 20:52:07.898492 2013] [mpm_winnt:notice] [pid 8432:tid 260] AH00456: Server built: Feb 23 2013 13:07:34 [Tue Nov 05 20:52:07.898492 2013] [core:notice] [pid 8432:tid 260] AH00094: Command line: 'c:\xampp\apache\bin\httpd.exe -d C:/xampp/apache' [Tue Nov 05 20:52:07.905492 2013] [mpm_winnt:notice] [pid 8432:tid 260] AH00418: Parent: Created child process 7588 [Tue Nov 05 20:52:08.882548 2013] [ssl:warn] [pid 7588:tid 272] AH01909: RSA certificate configured for www.example.com:443 does NOT include an ID which matches the server name [Tue Nov 05 20:52:09.467582 2013] [ssl:warn] [pid 7588:tid 272] AH01909: RSA certificate configured for www.example.com:443 does NOT include an ID which matches the server name [Tue Nov 05 20:52:09.534585 2013] [mpm_winnt:notice] [pid 7588:tid 272] AH00354: Child: Starting 150 worker threads. Fatal error: Allowed memory size of 134217728 bytes exhausted (tried to allocate 123731968 bytes) in C:\xampp\apps\drupal\htdocs\sites\all\themes\directory\node--job.tpl.php on line 41 Fatal error: Allowed memory size of 134217728 bytes exhausted (tried to allocate 123731968 bytes) in C:\xampp\apps\drupal\htdocs\sites\all\themes\directory\node--job.tpl.php on line 41

  Read the article

• I want to virtualize my workstation (Tier 1), Looking for Bare Metal Hypervisor for consumer grade components

  - by Chase Florell

  I find myself in this similar bind at least once a year. The bind whereby I'm either upgrading a motherboard, or an OS hard drive. It drives me crazy to have to reinstall Windows, Visual Studio, all my addins, reconfigure my settings etc... every single time. I have a layout and I like and I want to stick with it. My question is... Is there a Bare Metal Hypervisor on the market that will enable me to virtualize my consumer grade workstation? I really want to avoid Host/Client virtualization. Bare Metal is definitely a better way to go for my needs. Is this a good approach, or am I going to suffer some other undesirable side effects by doing this? Clarification My machine has very limited purposes. My primary use is Visual Studio 2010 Professional where I develop ASP.NET MVC Web Applications. The second piece of software that I use (that's system intensive) is Photoshop CS3. Beyond that, my applications are limited to Outlook, Internet Explorer, Firefox, Opera, Chrome, LinqPad, and various other (small) apps. Beyond this, I'm considering working on a node.js project and might run ubuntu on the same hypervisor if possible. System Specs: Gigabyte Motherboard Intel i7 920 12 GB Ram basic 500GB 7200RPM HDD for OS 4 VelociRaptors in Raid 1/0 for build disk Dual GTS250 (512MB) Graphics cards (non SLI) for quad monitors On a side note I also wouldn't be opposed to an alternative suggestion if the limitations are too great. I could install the ESXi (or Zen Server) on my box, and build a separate "thin client" to RDP into the virtual machine. It appears as though RDP supports dual monitors. Edit (Dec 9, 2011) It's been nearly a year since I first asked this question. Since then, there have been a lot of great strides in Hypervisor technology... AND MokaFive is now released for corporate use. I'd love to dig into this question a little more and find out if there is a solid BareMetal Hypervisor for workstations running consumer grade components (IE: not Dell, HP, Lenovo, Etc).

  Read the article

• Alternative Windows Offline Files + Windows Backup + Previous Version Setup

  - by Herson

  Currently our documents are all hosted in a Windows 7 box. Users can access the files using Windows share and the documents are available offline (windows 7 feature). The documents are being backed up daily by Windows 7 backup and restore utility. Users can access previous versions of the file (from the backups) using Windows Explorer "previous versions" feature. This setup is currently working well, except for the following: We would prefer to have access to hourly versions of the file, not daily. The previous version mechanism is tied up to the backup mechanism. Windows 7 performs a full backup every week and incremental backup everyday. The previous versions of a file is actually what are the available in the backups. If you 20GB documents and want to maintain at least three(3) year history, you will use at minimum 3 years * 52 weeks * 20GB or about 3TB even if there are few changes in the documents. Its pretty inefficient use of space. Looking up previous versions of a file is very slow (tens of minutes). This is probably related to the previous issue - Windows has to traverse its all of its backups. I am considering using SVN + autocommit/autoupdate tortoisesvn. It will have the following advantages: Backups are easy and will also backup the whole history of each documents. (Just backup the repository). Creating previous versions can be frequent. I think svn commit / update can be done every two minutes or so. Users can sync over the net. However, I can see the following issues: More conflicts than the original setup because both multiple users can now edit the same file even both are online, i.e. can connect to the SVN repo. The users can off course lock the file first before editing, but that would mean they have to adjust. Delay on propagation of file changes. On windows 7 file sharing, changes made by one online user will be instantaneously available to other online users. With the SVN setup, changes will only be propagated when the users execute the svn add/commit/update sequence. Delay will be probably a few minutes. This workflow will no longer work: "Hi, I just edited document X, can you have a quick look?" I would like to ask the opinion of the community for alternative setups, or improvements on the above setups to work out the kinks.

  Read the article

• Init script & the green [ OK ]

  - by Lord Loh.

  I am trying to install fast-cgi for nginx on an EC2 instance. I followed the steps explained here, but that is meant for Debian and does not work out of the box for a red-hat based system. I modified the script a bit to look like - #!/bin/bash ### BEGIN INIT INFO # Provides: php-fcgi # Required-Start: $nginx # Required-Stop: $nginx # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: starts php over fcgi # Description: starts php over fcgi ### END INIT INFO . /etc/rc.d/init.d/functions (( EUID )) && echo .You need to have root priviliges.. && exit 1 BIND=/tmp/php.socket USER=nginx PHP_FCGI_CHILDREN=15 PHP_FCGI_MAX_REQUESTS=1000 PHP_CGI=/usr/bin/php-cgi PHP_CGI_NAME=`basename $PHP_CGI` PHP_CGI_ARGS="- USER=$USER PATH=/usr/bin PHP_FCGI_CHILDREN=$PHP_FCGI_CHILDREN PHP_FCGI_MAX_REQUESTS=$PHP_FCGI_MAX_REQUESTS $PHP_CGI -b $BIND" RETVAL=0 start() { echo -n "Starting PHP FastCGI: " #ORIGINAL LINE #daemon $PHP_CGI --quiet --start --background --chuid "$USER" --exec /usr/bin/env -- $PHP_CGI_ARGS #MODIFIED LINE daemon --user=$USER $PHP_CGI -b $BIND& RETVAL=$? echo [ $RETVAL -eq 0 ] && touch /var/lock/subsys/php-fcgi #echo "$PHP_CGI_NAME." } stop() { echo -n "Stopping PHP FastCGI: " killall -q -w -u $USER $PHP_CGI RETVAL=$? echo "$PHP_CGI_NAME." rm /var/lock/subsys/php-fcgi } case "$1" in start) start ;; stop) stop ;; restart) stop start ;; *) echo "Usage: php-fastcgi {start|stop|restart}" exit 1 ;; esac exit $RETVAL The problem I have now is - service php-fcgi start keeps the shell blocked. If I run service php-fcgi start & and then ps aux, I see the php-cgi process running bound to the socket. I see the start command stop only when I execute service php-fcgi stop. How do I solve this blocking issue? I have tried adding an & at the end of the line spawning the daemon. But other scripts do not seem to be doing this. This is the most complicated script I am attempting to modify yet :-( How do I get the script to display the green [ OK ]? I checked scripts like httpd and saw that all they were doing was something as shown below. But I never see a green [ OK ] when I execute php-fcgi. I also discovered that putting echo_success with functions sourced displays the green [ OK ] but I do not see any other scripts in the /etc/rc.d/init.d/ executing echo_success or echo_failure. What have I got wrong? Also, How do i specify PHP_FCGI_CHILDREN with daemon? echo [ $RETVAL -eq 0 ] && touch /var/lock/subsys/

  Read the article

< Previous Page | 473 474 475 476 477 478 479 480 481 482 483 484  | Next Page >