Search Results

Search found 14989 results on 600 pages for 'street address'.

Page 480/600 | < Previous Page | 476 477 478 479 480 481 482 483 484 485 486 487  | Next Page >

• Virtual bridged networking with VLAN, could not ping

  - by v.yegy

  I require a virtual network with VLAN be build between two virtual hosts - which can be (lxc/ vbox -ubuntu or win xp). I tried with lxc and vbox with Ubuntu and was finding difficult to make it work without vlan, but was successful with vbox with xp. vbox-xp1 --- br1 ---------------- br2 ---- vbox-xp2 The config is: brctl addbr br1; brctl addbr br2 ifconfig br1 up; ifconfig br2 up stp br1 off; stp br2 off ip link add name br1-br2-l0 type veth peer name br1-br2-l1 sudo brctl addif br1 br1-br2-l0 sudo brctl addif br2 br1-br2-l1 vbox - xp 1 and 2 with network ; bridged and br1 and br2 respectively. The adapter is intel PRO/1000 MT Server and driver installed in guests. Configured IPs and two hosts pinged! VLAN config: ip link add link br1 name br1-2.5 type vlan id 5 brctl addif br2 br1-2.5 create vlan 5 in xp 1 and 2 and assign ip address Ping on with this config does not work. Wireshark trace on interface br1-br2-l1 / br1-2.5 shows that one ping results in ~240 ping packets and each growing by 4 bytes - first one being correct and 60, ping does not reach other host as I see mac is not learnt[arp -a]. -- if br1-2.5 is not configured, I see untagged packets in br1-br2-l1/0, but still not reaching other host as mac is not learnt. if br1-br2-l0/1 is made down, even if br1-2.5 is up, I count not see any packets. I tried with ebtables, but still could not make a correct config to work. -- If any one here are aware of any configuration, please let me know. I need to make a network of switches. Seems I have a very long way. Sorry for a very long question. Thanks and regards, vy

  Read the article

• What is the correct iptables rule when NATing multiple private subnets?

  - by Jose Mendez

  I have a Centos minimal 6.5 acting as a router. eth0 is connected to a Cisco switch trunk port, allowing VLANs 200-213. I have several VLAN interfaces just as this link suggests: https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Linux/6/html/Deployment_Guide/s2-networkscripts-interfaces_802.1q-vlan-tagging.html And have IPv4 forwarding, so all my network devices from any of the networks 200-213 can communicate with each other using this linux box as their router. Problem is, I need them to access the Internet, so I added the following rule: iptables -t nat -A POSTROUTING -s 192.168.0.0/16 -j SNAT --to 1.1.1.56 1.1.1.56 is the "outside" address. This works fine, devices connected to the internal networks can ping Intertnet addresses BUT, they stop being able to talk to each other across subnets, so 192.168.211.55 can ping 8.8.8.8, but can't talk to 192.168.213.5. As soon as I do a service iptables restart to remove the rule, I can start talking across internal subnets again. What would be the correct way to set up NAT for multiple private subnets? Or maybe the correct way to set up forwarding?

  Read the article

• Apache HTTPD - Segmentation fault when loading mod_jk module

  - by Hans Engel

  I just set up mod_jk with my Apache httpd 2.0.52 installation, but now when I try to start Apache, it has a segmentation fault. I've checked that I am using the mod_jk compiled for 2.0.x.. built against the same version I have, in fact. I've also verified that the path I'm giving to LoadModule is correct, and the permissions and the ownership of the file are the same as the rest of the modules'. When I remove the "LoadModule" command for mod_jk from my httpd.conf, there is no segmentation fault. Nothing shows in Apache's error logs. I have tried restarting the server with this module using both service httpd restart and httpd. These are the last few lines returned of strace httpd -X: gettimeofday({1292100295, 434487}, NULL) = 0 socket(PF_INET6, SOCK_STREAM, IPPROTO_IP) = -1 EAFNOSUPPORT (Address family not supported by protocol) socket(PF_NETLINK, SOCK_RAW, 0) = 3 bind(3, {sa_family=AF_NETLINK, pid=0, groups=00000000}, 12) = 0 getsockname(3, {sa_family=AF_NETLINK, pid=22378, groups=00000000}, [12]) = 0 time(NULL) = 1292100295 sendto(3, "\24\0\0\0\26\0\1\3\307\342\3M\0\0\0\0\0\305\333\267", 20, 0, {sa_family=AF_NETLINK, pid=0, groups=00000000}, 12) = 20 recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"<\0\0\0\24\0\2\0\307\342\3MjW\0\0\2\10\200\376\1\0\0\0"..., 4096}], msg_controllen=0, msg_flags=0}, 0) = 664 recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"\24\0\0\0\3\0\2\0\307\342\3MjW\0\0\0\0\0\0\1\0\0\0\10\0"..., 4096}], msg_controllen=0, msg_flags=0}, 0) = 20 close(3) = 0 socket(PF_INET, SOCK_STREAM, IPPROTO_IP) = 3 --- SIGSEGV (Segmentation fault) @ 0 (0) --- +++ killed by SIGSEGV +++ Process 22378 detached Has anyone had a similar problem using Apache 2.0.52 with mod_jk? I might try downloading and building the source for the Apache server and mod_jk myself if there isn't a discovered fix for this.

  Read the article

• Openfire on EC2 with Jingle

  - by Bjorn Roche

  I would like to run Openfire (or another XMPP server) on EC2. At the moment this is just for testing, so easy setup and configuration are important, as is low cost. At some point, however, if things go well, it will be important to scale this. Ideally, it would be nice to not have to switch software when the scaling happens, but if a switch needs to happen later it certainly can. My requirements are: basic XMPP services, including muc and pubsub. Logins controlled from an external API. Preferably, when a user attempts to connect, the XMPP server checks with the api to see if their username and password are correct, but I can also have the API keep the XMPP server up to date on new users, deleted users, pasword changes and so on. I see Openfire has a "user service" API. Not ideal, but it looks workable. Jingle, including relay and STUN. It's not at all clear to me if the Jingle Nodes plugin takes care of this. I'm a bit confused about what's required to set this up, and I'd rather know in advance than be confused along the way :). eg It seems like STUN servers require more than one IP address. Can Openfire do all this for me, including stun and media relay on a single machine? Is this hard to configure on EC2 with Openfire? What are the basic steps? Would this be easier with something else like, say Tigase? What about database? Should I use amazon's database service, or run a db on the same machine? Would the server be compatible with a service like http://www.siteuptime.com/ Thanks!

  Read the article

• Windows Server 2003 DHCP not handing out IPs

  - by SnOrfus

  I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254). My client machine is a Windows 7 (RC) machine and it has a connection but can't get an IP address. Even if I try setting the IP to a static 192.168.0.2 and there is still no connectivity. I can ping it from the server, but pinging the server from the client just times out. The only thing between the server and the client is a 24 port switch (D-Link DES-1024D). edit Ok, it turned out that the interfaces were setup backwards in the NAT settings (the internal nic connection was set to public and the external nic connection was set to private). I changed this and all was OK.... sort-of. Problem is now: If I set a static ip on the client (where I am typing this from) all is fine. BUT; when I set it to get it from DHCP, I get a correct IP from the server (192.168.0.2) but there is no internet on the client; but I can still ping the server fine from the client (which makes sense cause I was able to get an IP from it). edit I ended up just removing the Routing and DHCP server roles and just going with ICS for the time being until I get my hands on some better learning tools.

  Read the article

• How to determine which ports are open/closed on a FIREWALL?

  - by Rahl

  It seems no one has asked this question before (most regard host-based firewalls). Anyone familiar with port scanning tools (e.g. nmap) knows all about SYN scanning, FIN scanning, and the like to determine open ports on a host machine. Question is though, how do you determine the open ports on a firewall itself (disregard whether the host you're trying to connect to behind the firewall has those particular ports open or closed). This is assuming the firewall is blocking your IP connection. Example: We all communicate with serverfault.com through port 80 (web traffic). A scan on a host would reveal port 80 is open. If serverfault.com is behind a firewall and still allows this traffic through, then we can assume the firewall has port 80 open also. Now let's assume the firewall is blocking you (e.g. your IP address is under the deny list or is missing in the allowed list). You know port 80 has to be open (it works for appropriate IP addresses), but when you (the disallowed IP) attempt any scanning, all port scan attempts on the firewall drop the packet (including port 80, which we know to be open). So, how might we accomplish a direct firewall scan to reveal open/closed ports on the firewall itself, while still using the disallowed IP?

  Read the article

• Windows xp mapped drives disconnect from Windows 7 on Peer to Peer network

  - by Kathryn Codo

  I have a 5 user peer to peer network. 2-XP machines, 3- Windows 7 machines and a Windows 7 machine acting as the file server. I have NO issues with the Windows 7 machines staying connected via the mapped drives to the "server". However, once a day the 2 XP machines will not connect to the Windows 7 machine "server" via the mapped drives. I must restart the "server" in order to see the server and access the files via the mapped drives or Explorer. I have tried the persistent : yes command in NET USE, on the XP machines and also setting a static IP address on the "server". I've turned the firewall off on the "server:, no difference so I turned the firewall back on. No interruption occurs with the internet when this happens, just can't see the server. Again, the Windows 7 users are unaffected. I have gone into the advanced network settings on the "server" and added read/write permissions for Everyone as well as the users of the XP machines. I have double checked that we are all on the same WORKGROUP. I'm at a loss. It seems to happen around mid-day and I've not been able to find any activity that is happening at this time (Like someone plugging in a thumbdrive). Any suggestions would be greatly appreciated as my client is running old XP software he no longer has the disks for and needs for his engineering firm.

  Read the article

• Understanding what needs to be in place for a server to send outgoing email from a linux box

  - by Matt

  I am attempting to configure an openSuse 11.1 box to send outgoing email for a domain that the same server is hosting. I don't understand enough about smtp servers and the like to know what needs to be in place and working. The system already had Postfix installed, and I confirmed it was running via a > sudo /etc/init.d/postfix status I examined the Postfix config file in /etc/main.cf and configured a couple of items regarding the domain/host name and such, but left it largely default. I attempted to send an email from the command line with the following command: > echo "test 123" | mail -s "test subject" [email protected] Where differentdomain.com was not the same domain as the one best hosted on the server. However, the email never reaches the target account. Any suggestions? EDIT: In the postfix log, (/var/log/mail.info, there's nothing in .err) I see that postfix is trying to connect to what appears to be a different smtp server on our network, with a connection refused: connect to ourdomain.com.inbound15.mxlogic.net[our ip address]:25: Connection refused However, I can't figure out why it is 1) trying to connect to that server and 2) not just sending the messages itself... I mean, isn't postfix an smtp server? I did a grep -ri on ourdomain from /etc and see no configuration files anywhere telling it to do this. Why is it?

  Read the article

• Problems with ipsec betwen Cisco ASA 5505 and Juniper ssg5

  - by Oskar Kjellin

  I am trying to set up an ipsec tunnel between our ASA 5505 and a Juniper ssg5. The tunnel is up and running, but I cannot get any data through it. The local network I am on is 172.16.1.0 and the remote is 192.168.70.0. But I cannot ping anything on their netowork. I receive a "Phase 2 OK" when I set up the ipsec. I think this is the part of the config that is applicable. It seems like the data is not routed through the tunnel, but I am not sure... object network our-network subnet 172.16.1.0 255.255.255.0 object network their-network subnet 192.168.70.0 255.255.255.0 access-list outside_cryptomap extended permit ip object our-network object their-network crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 1 match address outside_cryptomap crypto map outside_map 1 set pfs crypto map outside_map 1 set peer THEIR_IP crypto map outside_map 1 set ikev1 phase1-mode aggressive crypto map outside_map 1 set ikev1 transform-set ESP-3DES-MD5 crypto map outside_map 1 set ikev2 pre-shared-key ***** crypto map outside_map 1 set reverse-route crypto map outside_map interface outside webvpn group-policy GroupPolicy_THEIR_IP internal group-policy GroupPolicy_THEIR_IP attributes vpn-filter value outside_cryptomap ipv6-vpn-filter none vpn-tunnel-protocol ikev1 tunnel-group THEIR_IP type ipsec-l2l tunnel-group THEIR_IP general-attributes default-group-policy GroupPolicy_THEIR_IP tunnel-group THEIR_IP ipsec-attributes ikev1 pre-shared-key ***** ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key *****

  Read the article

• 550 Forged HELO with postfix on debian lenny

  - by Martin Ahrer

  I'm running postfix on a debian lenny system. sending mail in general works without any problems. however some recipent mail systems return an error and I can't get a clue what is causing the problem. So far I suspect that this is either postfix setup itself or the reverse dns resolution. The mail server is running on a virtual server from my service provider. running the command hostname is returning my.domain however running host <ip-address> is returning some alias from the virtual server system. now i'm not quite sure if that is causing my problem???? The mail system <recipient-mail>: host mx0.recipient.domain[xxx.xxx.xxx.xxx] refused to talk to me: 550 Forged HELO: you are not my.domain Reporting-MTA: dns; my.domain X-Postfix-Queue-ID: 6A1135B08002 X-Postfix-Sender: rfc822; [email protected] Arrival-Date: Tue, 13 Apr 2010 17:50:36 +0200 (CEST) Final-Recipient: rfc822; recipient-mail Action: failed Status: 5.0.0 Remote-MTA: dns; mx0.recipient.domain Diagnostic-Code: smtp; 550 Forged HELO: you are not my.domain

  Read the article

• sql server 2008 cluster hang when a heavy load is run

  - by Billy OT

  we have a sql server 2008 active/active cluster running on wondows 2008R2 O/S. 14GB RAM, 4xCPU. we have set a ceiling of 12GB for sql server. We're running an agent job which loads 3 million records to a database. during this load the job fails and the cluster seems to attempt to fail over to the other node but unsuccessfully i.e., the cluster address is no longer accessible. we have to manually fail the cluster node back. during the load on viewing task manager we can see that memory usage hits a max of 12.5GB and CPU at times hits 100% on all 4 CPU, but for the most part fluctuates at an average of about 60%. I suppose my question is, will a cluster try to fail over if memory or CPU are taking a heavy hit? or am i barking up the wrong tree? also any ideas why it wouldn't fully fail over? we've crawled through logs, of which there are a lot, and can't find anything useful. we've also tried recreating the issue but it ran successfully at a later time. Also 3 million rows doesn't seem like a lot but in terms of resources should 14GB RAM and 4xCPU not be sufficient? Further information on this, we ran the load again today and corrupted the database! We received the error message : LogWriter: Operating system error 170. It looks like, under the heavy load, the sql cluster attempted to fail over and in doing so migrated a lun (or drive) which meant the disk was no longer reachable. (this is just our theory). The database is now 'suspect' and requiring restoration. The 170 error above also indicates that on failing over to the other node, the sql service could not start as it was already in use, therefore it couldn't fail over fully?? But I'm wondering why would it need to fail over in the first place? My assumptions could be completely wrong on this, so any ideas would be appreciated.

  Read the article

• Windows Server 2003 DHCP not handing out IPs

  - by SnOrfus

  I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254). My client machine is a Windows 7 (RC) machine and it has a connection but can't get an IP address. Even if I try setting the IP to a static 192.168.0.2 and there is still no connectivity. I can ping it from the server, but pinging the server from the client just times out. The only thing between the server and the client is a 24 port switch (D-Link DES-1024D). edit Ok, it turned out that the interfaces were setup backwards in the NAT settings (the internal nic connection was set to public and the external nic connection was set to private). I changed this and all was OK.... sort-of. Problem is now: If I set a static ip on the client (where I am typing this from) all is fine. BUT; when I set it to get it from DHCP, I get a correct IP from the server (192.168.0.2) but there is no internet on the client; but I can still ping the server fine from the client (which makes sense cause I was able to get an IP from it). edit I ended up just removing the Routing and DHCP server roles and just going with ICS for the time being until I get my hands on some better learning tools.

  Read the article

• How can I explain to dspam that the user "brandon" is the same as "brandon@mydomain"

  - by Brandon Craig Rhodes

  I am using dspam for spam filtering by running the "dspamd" daemon under Ubuntu 9.10 and then setting up a Postfix rule that says: smtpd_recipient_restrictions = ... check_client_access pcre:/etc/postfix/dspam_everything ... where that PCRE map looks like this: /./ FILTER lmtp:[127.0.0.1]:11124 This works well, and means that all users on my system get all of their email, whether "dspam" thinks it is innocent or not, and have the option of filtering on its decisions or ignoring them. The problem comes when I want to train dspam using my email archives. After reading about the "dspam" command, I tried this on the files in my Inbox and spam boxes (which date from when I was using another filtering solution): for file in Mail/Inbox/*; do cat $file | dspam --class=innocent --source=corpus; done for file in Mail/spam/*; do cat $file | dspam --class=spam --source=corpus; done The symptom I noticed after doing all of this was that dspam was horrible at classifying spam — it couldn't find any! The problem, when I tracked it down, was that I was training the user "brandon" with the above commands, but the incoming email was instead compared against the username "brandon@mydomain", so it was running against a completely empty training database! So, what can I do to make the above commands actually train my fully-qualified email address rather than my bare username? I would like to avoid having to run "dspam" as root with a "--user" option. I would have expected that the "dspam" configuration files would have had an "append_domain" attribute or something with which to decorate local usernames with an appropriate email domain, but I can't find any such thing. When I used to use the Berkeley DB backend to "dspam", I solved this problem by creating a symlink from one of the databases to the other. :-) But that solution eventually died because the BDB backend is not thread-safe, so now I have moved to the PostgreSQL back-end and need a way to solve the problem there. And, no, the table where it keeps usernames has a UNIQUE constraint that prevents me from listing both usernames as mapping to the same ID. :-)

  Read the article

• Dual Monitor support rdp 7 to win 7 on esxi

  - by rphilli5

  I am trying to RDP from a Windows 7 Professional dual monitor physical machine to a Windows 7 Professional VM hosted on esxi 4.0. I can get the spanning option to work to both monitors, but I have tried 3 different methods of connecting but have not been able to use true multiple monitors. At different times, I tried checking the "use all monitors" option, command line mstsc /multimon and added the line use multimon:i:1 to the .rdp file. None of these worked. Any ideas? The physical machine can connect to other Windows 7 physical machines with true multi monitor access. I also have the same issue when going from a 32bit RC1 machine to a Windows 7 Professional x64, but not when going in the reverse direction. Here's the .rdp: screen mode id:i:2 use multimon:i:1 desktopwidth:i:1440 desktopheight:i:900 session bpp:i:16 winposstr:s:0,1,341,118,1139,568 compression:i:1 keyboardhook:i:2 audiocapturemode:i:0 videoplaybackmode:i:1 connection type:i:1 displayconnectionbar:i:1 disable wallpaper:i:1 allow font smoothing:i:0 allow desktop composition:i:0 disable full window drag:i:1 disable menu anims:i:1 disable themes:i:1 disable cursor setting:i:0 bitmapcachepersistenable:i:1 full address:s:192.168.1.5 audiomode:i:0 redirectprinters:i:1 redirectcomports:i:0 redirectsmartcards:i:1 redirectclipboard:i:1 redirectposdevices:i:0 redirectdirectx:i:1 autoreconnection enabled:i:1 authentication level:i:2 prompt for credentials:i:0 negotiate security layer:i:1 remoteapplicationmode:i:0 alternate shell:s: shell working directory:s: gatewayhostname:s: gatewayusagemethod:i:4 gatewaycredentialssource:i:4 gatewayprofileusagemethod:i:0 promptcredentialonce:i:1 use redirection server name:i:0 drivestoredirect:s:

  Read the article

• How do I make dnsmasq serve IP addresses via IPoIB?

  - by Matt

  I have a cluster farm that I'm setting up. The nodes (computers in the farm) are connected via ethernet & IP over Infiniband. I'm needing to netboot the nodes and thought dnsmasq would fit well as it provides all the features including support for DHCP over IB and it works great for our ethernet setup. However, I can't seem to get it to provide IP addresses to the infiniband adaptors on the nodes. Each node is running an Ubuntu desktop 12.04 LTS. The dnsmasq server is running on ubuntu server 12.04LTS and has the following test config: dhcp-authoritative domain-needed bogus-priv expand-hosts no-hosts domain=local dhcp-range=eth0,10.0.0.10,10.0.0.255,12h dhcp-option=eth0,3,10.0.0.1 dhcp-range=ib0,10.1.1.10,10.1.1.255,12h dhcp-option=ib0,3,10.1.1.1 log-queries log-dhcp IPoIB works between nodes when configured statically but not with dhcp. On the nodes the file /etc/network/interfaces contains auto lo iface lo inet loopback auto ib0 iface ib0 inet dhcp #iface ib0 inet static #address 10.1.1.5 #netmask 255.0.0.0 up echo connected >`find /sys -name mode | grep ib0` Is there something I need to do on the client or server end to make this work?

  Read the article

• Cisco ASA and static IPv6 tunnel endpoint?

  - by Martijn Heemels

  I recently installed a Cisco ASA 5505 firewall on the edge of our LAN. The setup is simple: Internet <-- ASA <-- LAN I would like provide the hosts in the LAN with IPv6 connectivity by setting up a 6in4 tunnel to SixXS. It would be nice to have the ASA as tunnel endpoint so it can firewall both IPv4 and IPv6 traffic. Unfortunately the ASA apparently can't create a tunnel itself, and can't port-forward protocol 41 traffic, so I believe I would have to do one of the following instead: Set up a host with it's own IP outside the firewall, and have that function as tunnel-endpoint. The ASA can then firewall and route the v6 subnet to the LAN. Set up a host inside the firewall that functions as endpoint, separated via vlan or whatever, and loop the traffic back into the ASA where it can be firewalled and routed. This seems contrived, but would allow me to use a VM instead of a physical machine as endpoint. Any other way? What would you suggest is the optimal way to set this up? P.S. I do have a spare public IP address available if needed, and can spin up another VM in our VMware infrastructure.

  Read the article

• Can't ping a DNS zone on windows server 2008 R2

  - by Roberto Fernandes

  I´ve just configured a windows server 2008 r2, but got a lot of problems on DNS role. Let me talk about the server configuration: name: fdserver IP address: 192.168.0.10 I have a DNS zone called "fd.local". This is my domain and it´s working ok. I´ve created a zone called fdserver, and inside this zone a record (A) with "*" as a host. because this is a webserver, i´ve configured apache so if you enter something like "site.fdserver" it will point you to the "site" folder. This is working ok ONLY inside the server. This server is a DNS server too... and have 3 entries: 192.168.0.10 (his own IP), 8.8.8.8 and 8.8.4.4 (google public DNS). Now start the problems... Most of the computers on my network, CAN join the domain without problems. But just CAN'T ping "something.fdserver". Now comes the strange thing... If I remove the twoo secondary entries on my DNS server (8.8.8.8 and 8.8.4.4), it obvious stop accessing websites (like microsoft.com), but now the computer CAN ping "something.fdserver". I don´t know If I explained correctly... and my English is terrible... but inside the server is all working as it supposed to work. But in the workstation machines, it work only if I remove the secondary DNS!! If you need any details, just ask! thanks!

  Read the article

• Godaddy domain and Bluehost web hosting

  - by Digital site

  I have a domain from Godaddy and web hosting at Bluehost. I want to make this work as some people say no need to transfer the domain from Godaddy to Bluehost. I was trying to find out how to get this work out by adding name servers for Bluehost ns1.bluehost.com ns2.bluehost.com at Godaddy. This works fine, but not sure if 100% OK yet. The reason why I say that is when I type in my address name on any browser this way: mydomain.com it doesn't work. Instead I get an error message stating that this server is not found or couldn't connect to it... However, when I write the domain name and include the www. prefix it works fine... The other problem is when I search in google or yahoo, the domain shows like this: mydomain.com , which is not really good because my clients think my site is down because of the error message, and most new people don't know if they have to add www. to the domain to work. I just want to make at least the domain works like this: mydomain.com

  Read the article

• Unusual Caching Issue with IE 7/8 and IIS 7

  - by Daniel A. White

  We recently moved a site into production running Server 2008 x64 and IIS 7. The ASP.NET pages apparently load just fine, but when it comes to IE 7 and 8, a weird caching issue has cropped up with the CSS and JavaScript files on the page. On a very sporadic schedule, IE does not get all the files necessary to compose the page (i.e. CSS and JS files). When I manually go to the missing files from the address bar, they come back from local cache as empty. I F5 these source files and magically they come down properly. I refresh the site after loading a few files and the cache seems to hold. This problem has only been reproduced (again, sporadically) on IE 7 and 8 running XP. Chrome and Firefox appear to be immune. We have set IIS to use server-side kernel caching for CSS, JS and images. We also have set to expire content for the App_Themes and Scripts directories to expire immediately. One initial thought it was a SWF loading an FLV on page load. These fixes have not remedied the problem. We had no problems on our staging server which is using Server 2003 and IIS 6. Any ideas would be greatly appreciated. P.S. It sounds similar to this problem: but we do have the Static Content module installed. http://serverfault.com/questions/115099/iis-content-length-0-for-css-javascript-and-images

  Read the article

• OS X can't copy files from Windows Home Server...over wifi.

  - by John Clayton

  I'm a brand spanking new user of OS X, coming from a lifetime of Windows use. I've been setting up my new Macbook Pro and have run into a very unusual problem. Over wifi, I am unable to copy files to or from my Windows Home Server. The problem seems to exist only over wifi, and only to WHS. Here are the details of my setup: 2010 Macbook Pro (Core i7), OS X 10.6.3 Windows Home Server PP3 (virtualized in XenServer 5.5) Windows 7 Ultimate x64 desktop Windows 7 Ultimate x64 in Boot Camp D-Link DIR-655 wireless N router Here is what I've done to narrow down the problem: Files copy fine from WHS to OS X when using gigabit ethernet Files copy fine from desktop to OS X when using gigabit ethernet Files fail to copy from WHS to OS X when using wifi (error -51) Files copy fine from desktop to OS X when using wifi Files copy fine from WHS to Boot Camp when using wifi Files copy fine from desktop to Boot Camp when using wifi From what I can tell, it seems to be some sort of issue between OS X and WHS, but I can't for the life of me see what would be different between shares on WHS and my desktop. They are both connected using smb://ADDRESS (I've tried both by IP and name). I can browse the shares on the WHS, but copying to OS X fails. I originally found the issue while installing VS2010 off an ISO from WHS, mounted to a Windows 7 VM using VMware Fusion. During the installation the VM was unusable - even the clock got behind the host be about 8 minutes. Once I plugged in the ethernet and disabled the wifi things picked up and finished quickly. The Fusion 3.1 RC is the only I think of that I installed that may have messed with the wifi driver. I've also tried resetting the wifi router, and have changed it from being G & N to N-only. Under Boot Camp I get similar speeds as my wife's N laptop. Any ideas? Thanks!

  Read the article

• suggestions for firewall/router project using *BSD or Linux

  - by Adeodatus

  Hi All, I have a project in mind and I'd love to hear some ideas on some open source solutions with COTS hardware. I have a few 24 and/or 48 port managed layer2 switches with customers potentially on each port (though its usually about 20-30). Right now the switch has a bridged network and backhaul the traffic to our core to a centralized DHCP server. I need to move them to a NAT solution and, while doing this, I'd like to protect the customers on each port from the customer traffic on the other ports. I also need to be able to port forward from the public side of the firewall/nat box to specific hardware on the inside of the nat machine (easy enough, I know). My first thoughts are to build an appliance-like box (the fewer moving parts the better) that can do filtering and NAT with rfc1918 an address range being handed out via a DHCP server on the appliance. A caching DNS server on the appliance would be a plus since we backhaul everything to the core. I'd like to run FreeBSD but I'm open. Now, to try to limit the broadcast traffic thats visible I was thinking of doing each port on the switch as a different vlan and have the switch do trunking to the private NIC on the FreeBSD/appliance. I'd probably need to do some magic on the freebsd NIC to get this working but it should. We have the parts to build these systems. So, does this make sense? Are there any other solutions out there that we don't have to spend money on but can use our parts to create something? Are there any good distros that could do this already (monowall)?? I may or may not admin this solution so a secure web configuration and management tool would be a plus in the other admins' minds. Thoughts?

  Read the article

• Setting up a purely Node.js http server on port 80

  - by Luke Burns

  I'm using a fresh install of Centos 5.5. I have Node installed and working (I'm just using Node -- no apache, or nginx.), but I cannot figure out how to make a simple server on port 80. Node is running and is listening to port 80. I'm just using the demo app: var http = require('http'); http.createServer(function (req, res) { res.writeHead(200, {'Content-Type': 'text/plain'}); res.end('Hello World\n'); }).listen(80, "x.x.x.x"); console.log('Server listening to port 80.'); When I visit my IP, it does not work. I obtained my ipaddress using ifconfig. I've tried different ports. So there must be something I am missing. What do I need to configure on my server to make this work? I would like to do this without installing apache or nginx. Luke Edit-- Ok so, I installed nginx and started it up, to see whether or not it is related to node, and I don't see its welcome page. So it definitely has something to do with the server. Am I retrieving the IP Address correctly by running: ifconfig then reading the inet addr under eth0?

  Read the article

• Login to OS X Server User Account from Local Computer

  - by Brod Wilkinson

  I have OS X Server installed on a mac mini. I've created several User accounts, one of which is Account Name: Bob Password: abc123 From the Mac Mini's login screen I can choose "Server" (main account) "Bob" (Bobs account) and "Other..." OS X Server Accounts, from "Other..." if I input Bobs credentials it will log me in. I also have a macbook air, I would like to be able to select from the Login Screen "Other..." input Bobs credentials and have it login to Bobs account, or any other User Account for that matter. My Server is setup as private with the server address: server.network.private Following some googled instructions as well as apples very own instructions I have: Setup an Open Directory with Username: diradmin Password: abc123 Then on the macbook air gone into System Preferences > Users & Groups > Login Options and clicked Join next to Network Account Server, input my server (server.network.private) with diradmin credentials and its connected. Great. I've also ticked Allow Network Users to Login and Login Window and selected All Users. I was assuming this would allow my macbook air to login to the "Bob" account by selecting "Other..." from the login window although there is no "Other..." option. I then setup a VPN, basic credentials, logged into it on the macbook air and still not much has changed. I am able to share screens with the "Bob" account form my macbook air by logging in by clicking Share Screen... from the Finder under Shared > Network Server and then clicking Login In but this obviously requires the macbook air to already be logged into an account before it can share screens which is not suitable. Is there any way to simply login to the OS X Server User Account from the macbook air's login screen via the "Other..." like it does on the mac mini's login screen? Thanks in advance. Operating System: OS X 10.9 Mavericks OS X Server: Version 3

  Read the article

• Member Status: Inquorate in RHEL 5.6

  - by Eugene S

  I've encountered a strange issue. I had to change the time on my Linux RHEL cluster system. I've done it using the following command from the root user: date +%T -s "10:13:13" After doing this, some message appeared relating to <emerg> #1: Quorum Dissolved (however I didn't capture the message completely). In order to investigate the issue I looked at /var/log/messages and I've discovered these errors. Below is the output of few commands I got when tried to investigate the issue, however I don't have enough knowledge to make use of this information. [root@system1a ~]# clustat Cluster Status for system4081 @ Sun Mar 25 11:45:48 2012 Member Status: Inquorate Member Name ID Status ------ ---- ---- ------ chb_sys1a 1 Online, Local chb_sys2a 2 Offline [root@system1a ~]# cman_tool nodes Node Sts Inc Joined Name 1 M 872 2012-03-25 08:43:07 chb_sys1a 2 X 0 chb_sys2a [root@system1a ~]# qdiskd -f -d [17654] debug: Loading configuration information [17654] debug: 0 heuristics loaded [17654] debug: Quorum Daemon: 0 heuristics, 1 interval, 10 tko, 0 votes [17654] debug: Run Flags: 00000035 [17654] info: Quorum Daemon Initializing stat: Bad address [17654] crit: Initialization failed I tried to search through the internet and found out a quite similar issue here. However, for some reason I am not able to access the bug on bugzilla. The link to the bug is here

  Read the article

• Ubuntu server PPTPD with OS X clients Problems

  - by Nakedsteve

  I'm trying to get a PPTP server running on a ubuntu server, but I've run into some issues with it. I followed this guide on how to set up pptpd on my server, and everything went smooth, but when I try to connect with my mac, it gives me this error: Here's my configuration: Does anyone have any idea as to what I'm doing wrong here? Update: Here's what the pptpd.log has to say about it: steve@debian:~$ sudo tail /var/log/pptpd.log sudo: unable to resolve host debian Sep 3 21:46:43 debian pptpd[2485]: MGR: Manager process started Sep 3 21:46:43 debian pptpd[2485]: MGR: Maximum of 11 connections available Sep 3 21:46:43 debian pptpd[2485]: MGR: Couldn't create host socket Sep 3 21:46:43 debian pptpd[2485]: createHostSocket: Address already in use Sep 3 21:46:56 debian pptpd[2486]: CTRL: Client 192.168.1.101 control connection started Sep 3 21:46:56 debian pptpd[2486]: CTRL: Starting call (launching pppd, opening GRE) Sep 3 21:46:56 debian pptpd[2486]: GRE: read(fd=6,buffer=204d0,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Sep 3 21:46:56 debian pptpd[2486]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Sep 3 21:46:56 debian pptpd[2486]: CTRL: Reaping child PPP[2487] Sep 3 21:46:56 debian pptpd[2486]: CTRL: Client 192.168.1.101 control connection finished My pptpd options are: asyncmap 0 noauth crtscts lock hide-password modem debug proxyarp lcp-echo-interval 30 lcp-echo-failure 4 nopix

  Read the article

< Previous Page | 476 477 478 479 480 481 482 483 484 485 486 487  | Next Page >