Search Results

Search found 19759 results on 791 pages for 'cellular internet'.

Page 481/791 | < Previous Page | 477 478 479 480 481 482 483 484 485 486 487 488  | Next Page >

• Router startup problems

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the power off and on again it all works. I also have to restart my PC too in order for everything to work. How can I solve this problem? Just leave the router turned on all time? I prefer a daily IP switch, though. May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• iptables secure squid proxy

  - by Lytithwyn

  I have a setup where my incoming internet connection feeds into a squid proxy/caching server, and from there into my local wireless router. On the wan side of the proxy server, I have eth0 with address 208.78.∗∗∗.∗∗∗ On the lan side of the proxy server, I have eth1 with address 192.168.2.1 Traffic from my lan gets forwarded through the proxy transparently to the internet via the following rules. Note that traffic from the squid server itself is also routed through the proxy/cache, and this is on purpose: # iptables forwarding iptables -A FORWARD -i eth1 -o eth0 -s 192.168.2.0/24 -m state --state NEW -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A POSTROUTING -t nat -j MASQUERADE # iptables for squid transparent proxy iptables -t nat -A PREROUTING -i eth1 -p tcp --dport 80 -j DNAT --to 192.168.2.1:3128 iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 80 -j REDIRECT --to-port 3128 How can I set up iptables to block any connections made to my server from the outside, while not blocking anything initiated from the inside? I have tried doing: iptables -A INPUT -i eth0 -s 192.168.2.0/24 -j ACCEPT iptables -A INPUT -i eth0 -j REJECT But this blocks everything. I have also tried reversing the order of those commands in case I got that part wrong, but that didn't help. I guess I don't fully understand everything about iptables. Any ideas?

  Read the article

• DLINK WBR-1310B Wireless Router seems to hang...

  - by Ira Baxter

  I have a brand new DLINK-1310B Wireless Router (box never before opened, although I bought it the neighborhood computer junk store). I am using it at home (and in fact am using it this instant from a wireless laptop). When operative, I can ping it at 192.168.0.1, and I can log into it from the PC attached to by LAN and from the wireless PC at //192.168.0.1. In the course of the day since I've installed, it seems to have locked up 3 times. Each time the symptoms are my web browser (or other internet service) stops with a "No internet connection" error. Attempts to contact the router via 192.168.0.1 get no reaction, from either the wireless laptop or from the hardwired PC sitting next to it. It doesn't respond to pings to that address either. Rebooting fixes it. Its brand new. I've seen discussion in other questions about aging cheap electronics. Its too new to be aged. Anyboyd else seen this behavior with a DLINK-1310? Or do I just need to exchange it for another and try again? (I hate rolling dice, I bought the DLINK becuase a previous Linksys died of apparant heating problems). Remarkably, nobody talks about how much software is in a router. Is the stuff just buggy?

  Read the article

• Encrypted WiFi with no password?

  - by Ian Boyd

  Is there any standard that allows a WiFi connection to be encrypted, but not require a password? i know that (old, weak) WEP, and newer WPA/WPA2 require a password (i.e. shared secret). Meanwhile my own wireless connections are "open", and therefore unencrypted. There is no technical reason why i can't have an encrypted link that doesn't require the user to enter any password. Such technology exists today (see public key encryption and HTTPS). But does such a standard exist for WiFi? Note: i only want to protect communications, not limit internet access. i get the sense that no such standard exists (since i'm pretty capable with Google), but i'd like it confirmed. Claraification: i want to protect communcations, not limit internet access. That means users are not required to have a password (or its moral equivalent). This means users are not required: to know a password to know a passphrase to enter a CAPTCHA to draw a secret to have a key fob to know a PIN to use a pre-shared key have a pre-shared file to possess a certificate In other words: it has the same accessibility as before, but is now encrypted.

  Read the article

• Can I make TCP/IP session to run less than 60 seconds?

  - by par

  Our server is overloaded with TCP/IP sessions, we have 1200 - 1500 of them. Most of them are hanging in TIME_OUT state. It turns out that a connection in TIME_OUT state occupies a socket until 60 second time-out is elapsed. The problem is that the server gets unresponsive and many clients are not getting served. I have made a simple test: download an XML file from the server with Internet Explorer 8.0 The download finishes in a fraction of second. But then I see that the TCP/IP connection is hanging in TIME_OUT state for 60 seconds. Is there any way to get rid of TIME_OUT waiting or make it less to free the socket for new connections? I understand why TCP/IP connection enters TIME_OUT state, but I don't understand why Internet Explorer does not close the connection after the XML file download is over. The details. Our server runs web service written in Perl (mod-perl). The service provides weather data to clients. Client is a Flash appication (actually Flash ActiveX control embedded in Windows application). OS: Ubuntu Apache "Keep Alive" option is set to 0

  Read the article

• Problem with network after malware attack

  - by Cruelio

  Im trying to help some friends with a Win XP machine. I got rid of the malware using Malware Bytes, and HiJackThis. But now they(I) have another problem. When the computer boot into Windows it seems fine. When I start Internet Explorer the browser window opens just fine, but nothing happens for at minute or two. After the two minutes of waiting, the network icon appears in the taskbar next to the clock, and then everything works. The computer is connected to the internet using a Ethernet adapter. I have looked at the Rvent Log and found an error from Perfnet with eventid 2004 <Provider Name="PerfNet" /> <EventID Qualifiers="49152">2004</EventID> <Level>2</Level> <Task>0</Task> <Keywords>0x80000000000000</Keywords> What I have tried so far: In the device manager i have uninstalled the Ethernet adapter and installed it again. I have uninstalled and installed the Windows File and Printer Sharing service. I have verified that both server and workstation services are started. What should I do next?

  Read the article

• VLAN for WiFi traffic separation (new to VLANing)

  - by Philip

  I run a school network with switches in different departments. All is routed through to a central switch to access the servers. I would like to install WiFi access points in the different departments and have this routed through the firewall (an Untangle box that can captive-portal the traffic, to provide authentication) before it gets onto the LAN or to the Internet. I know that the ports that the APs connect to on the relevant switches need to be set to a different VLAN. My question is how do I configure these ports. Which are tagged? Which are untagged? I obviously don't want to interrupt normal network traffic. Am I correct in saying: The majority of the ports should be UNTAGGED VLAN 1? Those that have WiFi APs attached should be UNTAGGED VLAN 2 (only) The uplinks to the central switch should be TAGGED VLAN 1 and TAGGED VLAN 2 The central switch's incoming ports from the outlying switches should also be TAGGED VLAN 1 and TAGGED VLAN 2 There will be two links to the firewall (each on its own NIC), one UNTAGGED VLAN 1 (for normal internet access traffic) and one UNTAGGED VLAN 2 (for captive portal authentication). This does mean that all wireless traffic will be routed over a single NIC which will also up the workload for the firewall. At this stage, I'm not concerned about that load.

  Read the article

• Linux drivers for laser printer Konica Minolta Magicolor 4750DN

  - by user51166

  I would like to install the konica minolta magicolor 4750DN in Linux (debian 64 bits, I know it's not really supported but that's not the issue right now) but all the manual says is "put the CD rom in and copy the drivers and PPD file". However I did not get the CD ! On their "fantastic" internet site (...) there are only available drivers for Windows and Mac OSX. I tried to extract the ppd file from the .dmg file for MacOSX 10.7 but, if the PPD file works, a compiled file (only mac compiled, MACH 4 architectures says the "file" command) does not (obviously "cannot execute binary file", since I'm trying to run a Mac file on Linux). Is there anybody who has the same printer that could lend me the Linux drivers on the CD ROM ? Couldn't find them anywhere on the internet. Any way to execute a Mach (or BSD) binary file on Linux (I don't think is possible, although some "emulators" may exist). Thank you very much. I buyed this printer even because it was advertised as "Linux compatible", only to get this bad surprise. I would be grateful if you could help me solve this problem.

  Read the article

• maximum number of connections Squid

  - by Isaac

  I have a Squid proxy server that controls all internet traffic for my network. I need a way to stop users from downloading big files (say 50MB) in my network. I banned some famous ports (e.g. torrent) but some downloads are possible by HTTP port. Obviously I cannot ban port 80! A simple solution is limiting maxmimum number of the simultaneous connections for each IP (e.g. 3 connections). It's possible in Squid with this config: acl ACCOUNTSDEPT 192.168.5.0/24 acl limitusercon maxconn 3 http_access deny ACCOUNTSDEPT limitusercon But this solution has really bad impact in web browsing, because any smart browser get different parts of a website by several connections simultaneously to speedup web browsing. But if we have a maximum number of connections, the browsers will fail to get some parts and the website will be shown partially and some parts/images/frames will not be shown. So, can we limit maximum number of persist connections? I think this policy will works: Specify Maximum number of connections that is alive for 10 seconds But Number of simultaneous connections for every IP is unlimited But how can we implement this policy when Squid? With which config? UPDATE: artifex and Tom Newton offered using a bandwidth-limiting approach to fight against downloaders. But bandwidth-limiting in Squid has a shortcoming: It's static and cannot dynamically change. So a person has a limited bandwidth not matter how many people are using internet (maybe nobody!) Also, this solution cannot help to stop people from downloading. They still can download but in a lower speed. But if we find a way to terminate persist connections (or any connection that is alive more than a specific time), downloading big files will be almost impossible (always there is some way!)

  Read the article

• Server 2003 PDC DNS not working..Failover server is...

  - by Seth

  In the midst of trying to utilize proc power, i create a fault tolerant DNS server a while ago. Since, Ive been trying to add another controller for exchange. So I thought I would revert back to a single primary DNS for the meantime and now Im balancing on a thread. The server i thought I uninstalled DNS, is still acting as DNS. And now the PDC does not resolve. Can anybody walk me through, Im overwhelmed and cant think straight... Im afraid if anyone restarts their machine they wont have internet. Update Ok so from the beginning. I was configuring Exchange on a new server 2008. How it happened I dont know, but it started to not resolve DNS. (exclamation mark on NIC) even though everything was static. So ultimately I decided to remove the server from the problem, because I noticed DNS was in disarray if I used the DNS IP of the first server. This is when I tested with nslookup on each DNS server. I had uninstalled DNS from the second server, but nslookup was still resolving with that IPaddress, which has me all wound up cause I dont understand. So, since the first DNS server isn't resolving, Im assuming if the second one isnt configured right I'll loose internet. Im just confused and dont know where to start troubleshooting...

  Read the article

• All application passwords lost on Windows 7

  - by Rynardt

  A couple of days ago I changed my Windows 7 login password. My laptop is on my company's domain, so password changes are done over the internal network. Since changing the password I noticed that all my saved Chrome passwords are missing. Also Skype, Windows Live, Internet Explorer and Outlook lost their saved passwords. I guess there could be more applications with lost passwords, but I have not opened them yet. This makes me think that most applications saves their passwords to a general password vault on the Windows system and this vault got somehow corrupted when I changed my domain login password for windows. Do anyone have any idea of how to fix this and prevent it from happening again? EDIT : More Info I do development work at the office, so most of the time I bypass the firewall and connect directly to the internet gateway. Now and then I would connect to the company wifi network to do printing and access files on a NAS. So by default my laptop does not connect to the wifi hotspot. On this occasion to update the password, I had to connect to the wifi. So referring to the comment by OmnipotentEntity below, could this have happened when the system rebooted without a connection to the network as the laptop does not auto connect to the wifi hotspot?

  Read the article

• Configure Domino to use SMTP routing and hMailServer

  - by Sébastien Lachance

  I have been trying for a couple of days to set up a Domino 8.5 server. Basically, I want everything to be run inside a local network. Right now I can send email to other user in the Domino directory without any mail address. I am pretty new to all this stuff, so maybe the answer will be really obvious. What I need to do is be able to send a mail from somewhere else to a domino user that will be redirected to his account. On the Domino server, I also have hMailServer installed on port 25. I configured Domino to use port 26. I followed those step to get where I am now. -I have set the Fully qualified Internet host name to "preview.notes". -Smtp Listener task changed to Enabled to turn on the Listener so that the server can receive messages routed via SMTP routing -Setting up SMTP routing within the local Internet domain (http://www.h2l.com/help/help85%5Fadmin.nsf/f4b82fbb75e942a6852566ac0037f284/7f9738a49efc4f58852574d500097b01?OpenDocument) -I modified the person to use the [email protected] address. -I'm using the hMailServer (which have the local "preview.local" domain name) to send mail to [email protected]. When sending mail I got an error telling that the DNS is not set up correctly. Is using the Domino Smtp server instead of hMailServer will solve the problem? I can Telnet the Domino Smtp Server.

  Read the article

• Route specific network traffic through vpn in virtualbox guest

  - by Sander

  I am running OSX with a windows server 2008 guest in Virtualbox. My goal is to route some of the network traffic in the host through the server guest. This is because the win2008 server has a VPN connection to my workplace using a Smartcard solution which can not operate on OSX. My current set-up is like this: OSX (Host): connected to the internet via en01 Win2008 (Guest): connected to the internet using NAT (lan1 in guest) has a SSTP VPN connection to my workplace is connected to the guest using an Host Only Adapter vboxnet0 (LAN2 in guest) The important part is about the host (OSX). Primarily I want all network traffic to just go through en01. However, all traffic which can only be accessed through the VPN must go through the guest and through the VPN. I have one specific FQDN which can only be accessed through the VPN (say corp.mycompany.com). I do not know much about networking. I thought I would be able to get it to work by bridging together LAN2 and LAN1 but this didn't seem to work this: http://archives.aidanfindlater.com/blog/2010/02/03/use-vpn-for-specific-sites-on-mac-os-x/ using a loopback adapter on WinXP (when I did not have win2008 yet, but this doesn't work because I can't create a PPTP connection) And I've also read about Routing and Remote Access but I have no idea on how to use this. Can someone help me in the right direction?

  Read the article

• 802.11g -> wired ethernet bridging not working

  - by Malachi

  Usually people want to go the other direction, but I want to take our relatively fast and stable house 802.11g signal and bridge it to ethernet. I have tried using an Airport Express (the b/g flavor) and my i7 MacBook pro, both to no avail. Word is that the b/g flavor of This flavor of Airport Express maxes at firmware 6.3 which doesn't support this kind of bridging properly. However, I expected my MacBook pro to do the job with its "Internet Sharing" feature. Alas, although my wired PC does sort of see it, it doesn't work out. Strangely, using DHCP the PC receives the same IP address as my MBP uses on the network. Less strangely, but still surprisingly, the wired ethernet port on my mac registers as the IP address of the gateway when queried with IFCONFIG. It sort of makes sense that the mac would "pretend" to be the gateway, but the whole thing just isn't working and seems configured wrong - but all the docs I see say basically "OS X Internet Sharing: click it and go". What do I do? Do i really have to buy more hardware, even though I have plenty of would-be candidates for bridging? Incidentally, the host router originating the 802.11g signal is a belkin 802.11g router, and is documented to support WDS.

  Read the article

• Privacy, VPN and routers

  - by user123189

  Ever since this ACTA push-up the things are starting to heat up around torrents and privacy. I am using Tribler now, but this is not secure enough for me. Not enough privacy. I've been using in the past a swedish VPN PPTP connection. What I observed is that, when the VPN connection was down, Internet traffic wasn't cut off, rather the downloads were continuing, this time with my real IP, wearing off my protection. 1st : How to enforce a VPN connection that will cut all traffic when down? That is, the moment the connection is down, all internet traffic should cease as if I'd pull the network plug out. 2nd: Is PPTP good enough or should I ask for SSTP or IKEV2 ? 3rd: Should I disable IPv6 ? Is VPN no longer private if I keep IPv6 active? I 'heard some stuff' about dual vpn routers to be able to improve privacy; but nothing more about how to configure one for such a task. 4th: Is there any kind of "black box" hardware equipment that can be used in hiding IP, encrypting traffic and so on ?

  Read the article

• How do I collect SNMP readings from intermittently-connected sites?

  - by Luke404

  I am collecting SNMP data on-site for a number of systems, currently using Cacti. These systems are spread on a number of sites that aren't always connected to internet, but I also need to centralize the data on a single system (datacenter housed server) and get graphs out of it. If I directly poll remote systems with a centralized Cacti I'd loose data when a site is not connected to internet. I should record data on-site (I have a server at each site and I can run whatever I want on it) and then 'sync' everything to the central system. One hack could be a cacti or directly an rrdtool on site and then periodically rsync RRD data to the central Cacti system, but that doesn't sound like a 'clean' solution: every RRD would have to be defined at both places and rsync scripts setup with the specific file names. Can you suggest a better solution? Cacti is not a requirement but I'd like to use something like that on the central system. On-site systems need only to collect data I don't need to graph it there or manage users rights to view data and stuff like that, users will only access the centralized system.

  Read the article

• Debian, 2 NICs load-balancing or agregating with one same gateway

  - by pouney

  Hi, I have one server, with double NICs connected to one switch with the same gateway. Behind the switch we have internet. |Debian| - eth0 - switch - internet - eth1 - same I don't understand how to load-balancing between eth0 and eth1. The inbound/outbound traffic always use eth1. This is the config: # The primary network interface allow-hotplug eth0 auto eth0 iface eth0 inet static address 192.168.248.82 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 allow-hotplug eth1 auto eth1 iface eth1 inet static address 192.168.248.83 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth1 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth0 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth0 Ips aren't real, it's just for the example. Anybody have an idea on correct routing to use eth0 on 192.168.248.82 and eth1 on 192.168.248.83 ? I have many example for multiple gateway but here it's the same. Thanks all. Regards

  Read the article

• Connect to Nonencrypted Wireless Network Using Ubuntu Commands

  - by Tim

  I failed to connect to an open i.e. nonencrypted wireless network using Ubuntu command lines. Here is what I did: $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo /sbin/ifconfig wlan0 up $ sudo iwconfig wlan0 essid "Cavalier High-Speed 866-4-CAVTEL" $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 10812 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. Trying recorded lease 192.168.1.67 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms Trying recorded lease 192.168.1.45 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. $ sudo /sbin/iwconfig wlan0 wlan0 IEEE 802.11bg Mode:Managed Frequency:2.422 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I was wondering what the problem is and how I can do it right? Thanks and regards!

  Read the article

• I need a reverse proxy solution for SSH

  - by Bond

  Hi here is a situation I have a server in a corporate data center for a project. I have an SSH access to this machine at port 22.There are some virtual machines running on this server and then at the back of every thing many other Operating systems are working. Now Since I am behind the data centers firewall my supervisor asked me if I can do some thing by which I can give many people on Internet access to these virtual machines directly. I know if I were allowed to get traffic on port other than 22 then I can do a port forwarding. But since I am not allowed this so what can be a solution in this case. The people who would like to connect might be complete idiots.Who may be happy just by opening putty at their machines or may be even filezilla.I have configured an Apache Reverse Proxy for redirecting the Internet traffic to the virtual machines on these hosts.But I am not clear as for SSH what can I do.So is there some thing equivalent to an Apache Reverse Proxy which can do similar work for SSH in this situation. I do not have firewall in my hands or any port other than 22 open and in fact even if I request they wont allow to open.2 times SSH is not some thing that my supervisor wants.

  Read the article

• MacBook Air Keeps dropping Wi-Fi

  - by Robert Patrick

  So my MacBook Air keeps dropping Wi-Fi for some reason. It happens ONLY on my home network, and ONLY to my computer. I'm using a Linksys WRT54G router. I'm the only Mac on the network. Every other Wi-Fi network is perfectly fine, and every other computer on this network is fine. Many things can happen. It could say it's connected, but not be able to access the internet (whether it tells me that there's no internet access or not). It may just drop Wi-Fi altogether, and refuse to connect. Generally, if I unplug the router and plug it back in, it's all good. It also works if I restart my computer. This happens multiple times a day. Yesterday I did everything I know to get it to connect (restart router many times, restart my MacBook), and nothing worked. Eventually it just magically worked. How can I stop this from happening? We got a notice from Comcast a while ago saying that a bot called DNS Changer was detected on one or more machines on the network. I'm assuming that this can't be me, right?

  Read the article

• Strange RDP / Remote Desktop problem

  - by John Landheer

  I'll try to be as specific as I can be: Server is running SBS 2008 R2 (with all updates) Server is connected to the internet Server has 2 NIC's, one is disabled Server is running RDP Service (accessible directly from the internet, I know, not as secure as it should be) Computers A and B are on the same local net. Computers A and B are both Windows 7. Users X and Y are both admins on the server Computer A can connect as user X to the server with mstsc Computer A can connect as user Y to the server with mstsc Computer B can connect as user X to the server with mstsc Computer B CANNOT connect as user Y to the server with mstsc! Error that username/password is incorrect. The last point is the problem, I get an authentication error. This used to work flawlessly for the last year. The server and desktops have been rebooted. EDIT: I tried: prefixing domain to the username prefixing the server computer name to the username change the password copy/paste the password from notepad to make sure it was correct I find it very strange.... EDIT: The computers are not on the same subnet as the server. The server is at my hosting provider. All computers as all users can reach the web app that is running on the server.

  Read the article

• Iptables rules, forward between two interfaces

  - by Marco

  i have a some difficulties in configuring my ubuntu server firewall ... my situation is this: eth0 - internet eth1 - lan1 eth2 - lan2 I want that clients from lan1 can't communicate with clients from lan2, except for some specific services. E.g. i want that clients in lan1 can ssh into client in lan2, but only that. Any other comunication is forbidden. So, i add this rules to iptables: #Block all traffic between lan, but permit traffic to internet iptables -I FORWARD -i eth1 -o ! eth0 -j DROP iptables -I FORWARD -i eth2 -o ! eth0 -j DROP # Accept ssh traffic from lan1 to client 192.168.20.2 in lan2 iptables -A FORWARD -i eth1 -o eth2 -p tcp --dport 22 -d 192.168.20.2 -j ACCEPT This didn't works. Doing iptables -L FORWARD -v i see: Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 33 144 DROP all -- eth1 !eth0 anywhere anywhere 0 0 DROP all -- eth2 !eth0 anywhere anywhere 23630 20M ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- eth1 any anywhere anywhere 175 9957 ACCEPT all -- eth1 any anywhere anywhere 107 6420 ACCEPT all -- eth2 any anywhere anywhere 0 0 ACCEPT all -- pptp+ any anywhere anywhere 0 0 ACCEPT all -- tun+ any anywhere anywhere 0 0 ACCEPT tcp -- eth1 eth2 anywhere server2.lan tcp dpt:ssh All packets are dropped, and the count of packets for the last rule is 0 ... How i have to modify my configuration? Thank you. Regards Marco

  Read the article

• Router startup problem

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the pow*emphasized text*er off and on again it all works. The problem is regarding startup only, when I get it to work everything runs as smooth as a 1980-s text-based C++ game on a 3ghz machine. I also have to restart my PC too in order for everything to work. - How can I solve this problem? - Just leave the router turned on all time? I prefer a daily IP switch, though. - May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• Best all in one linux based proxy,firewall, dhcp and wins server.

  - by BeStRaFe

  I help to run a lan in Sydney. We have a need for a proxy/gateway solution to allow those pesky games that require internet to work. I have been doing this with an ISA server and it has worked quite well. However now i wish to port this over to run on the same hardware as our cacti / nagios box under a vmware VM. ISA server is horridly nad due to the massive ram and i/o requirement for something is basically port blocking and handing out IP's. The needs are as follows. 1. DHCP 2. WINS (otherwise network devices fight over who is the WINS master) 3. Filtering based in PORT for outbound traffic. 4. Ability to whitelist IP/MAC's for internet access. 5. Web Interface. I had been thinking to use PFSENSE however there is no option for a WINS server and i cbf working my way around bsd.

  Read the article

• Single m0n0wall - Two LAN Subnets - How To Setup

  - by SnAzBaZ

  I have two LAN subnets that I need to link together they are 192.168.4.0/24 and 192.168.5.0/24 There is a m0n0wall running on 192.168.4.1. It's LAN connection goes out to our network switch, and it's WAN port goes out to our ADSL modem. WAN is connected via PPPoE. The 192.168.4.0 subnet contains all of our office workstations. The 192.168.5.0 subnet contains development servers and test machines that need to obtain internet access and be "managed" by computers on the 192.168.4.0 subnet, but need to be on their own subnet as well. I have a Draytek 2820N configured on 192.168.5.1 with it's WAN2 port configured as 192.168.4.25 and a default gateway of 192.168.4.1. Machines on the 5.0 subnet can connect to the internet via the m0n0wall just fine. I configured a static route on the m0n0wall LAN interface, Network 192.168.5.0/24 and Gateway 192.168.4.25. Machines on the 5.0 subnet can ping machines on the 4.0 network but the reverse does not work. I configured a new firewall rule on the m0n0wall that allows any traffic on the LAN interface with a source IP of 192.168.4.25 to be allowed. The DrayTek firewall is currently configured to pass all traffic regardless. When I try to ping a machine in the 5.0 subnet from 4.0 I see this in my m0n0wall log: BLOCK 14:45:27.888157 LAN 192.168.4.25 192.168.4.37, type echoreply/0 ICMP So the reply is being sent from the 5.0 subnet but is not being allowed to reach my workstation because the firewall is blocking it. Why is the firewall blocking it ? I hope the explanation of my network is clear, please ask if you require further clarification. Thank you.

  Read the article

< Previous Page | 477 478 479 480 481 482 483 484 485 486 487 488  | Next Page >