Search Results

Search found 18766 results on 751 pages for 'me again'.

Page 483/751 | < Previous Page | 479 480 481 482 483 484 485 486 487 488 489 490  | Next Page >

  • Sony Ericsson Windows driver problem

    - by alex
    I've installed Update Service and MediaGo for my Sony Ericsson phone but one of the drivers that was installed along with the software is causing problems in Windows 7 x64. Looking in the Event Log I see the following warning: Detected unrecognized USB driver (\Driver\seehcri) This is the driver corresponding to the Sony Ericsson seehcri Control Device. The failure to recognize the USB driver is causing problems with other services, namely the VMware USB Arbitration Service. It should normally start automatically but, due to the failure to recognize the seehcri USB driver, it fails with the following error: Error 31: A device attached to the system is not functioning. Disabling the driver has not helped at all. The VMWare service still refuses to start and I keep getting both warnings in the Event Log. I would like to remove the Sony Ericsson driver but unfortunately, that's not possible. Uninstalling the Sony Ericsson seehcri Control Device from Device Manager causes Windows to almost completely freeze up while trying to look for drivers for unrecognized hardware. Windows tries over and over again to locate and install drivers for an Unknown device, failing every time. Looking in Device Manager, it simply fills up with hundreds of unknown devices, also using up the CPU to almost 85% in the process. What should I do? How can I safely remove the driver without causing Windows to look for a new driver?

    Read the article

  • Formatting a truecrypt volume on windows: Truecrypt failed to obtain administrator privileges

    - by daveh551
    Following shaneselman's advice (http://www.hanselman.com/blog/TheComputerBackupRuleOfThree.aspx), I'm setting up a 2TB external drive as a backup, and encrypting it using TrueCrypt. This is under Windows 7. (I've used TrueCrypt before, but not since XP days.) I installed TrueCrypt with default options. After taking 23 hours to format the 2TB container, it finishes with an error saying "TrueCrypt cannot obtain administrator privileges." When I click OK on that, it says it can't format the container as NTFS, do I want to format it as FAT, and I don't so I click No, and it exits with nothing to show for 23 hours of compute time. So I set the "Run as administrator flag" on the TrueCrypt shortcut, and try again. This time, when I go to format the contain (prepared to wait ANOTHER 23 hours), it pops up a dialog saying you're formatting this as administrator. "The volume may be created with permissions that will not allow you to write to the volume when it is mounted. If you want to avoid that, close this instance of Volume Creation Wizard and launch a new one without administrator privileges." Great - I can either run as non-administrator, and it will fail to create the volume at all, or I can run as administrator and create a volume I can't write to. I think I'm doing something wrong, but it's not clear to me what. Any help?

    Read the article

  • Windows telling me, the local security authority is internally inconsistent upon mounting a network drive

    - by acme
    Since ages I've mounted a network share (via samba to a Linux machine) in Windows 7 to access it via drive letter. This worked flawlessly so far. Until now. Suddenly I couldn't access the drive anymore. Windows was telling me the network name (I didn't remember the exact term) was already in use. So I disconnected and tried to connect again: net use Y: \\10.10.10.208\work After a long time I get a message saying "The Local Security Authority (LSA) database contains an internal inconsistency" A restart didn't help. The mapped share is accessible (works on other machines in the same network), so obviously something strange is going on on my machine. Can anyone tell me how I can fix this inconsistency? Update: All machines that have saved the login information refuse with this error. So it must be something with the authorization. When I use net use Y: \\10.10.10.208\work /user:raphael it prompts me for the password and then returns that error message.

    Read the article

  • Windows 2012/IIS 8 + ASP.NET MVC Applicaiton 403.14 (Forbidden) - The Web server is configured to not list the contents

    - by WiredPrairie
    I have a very simple MVC 4 application I'm trying to deploy to a Windows 2012 server. Inconsistently, when navigating to the root of the web application (http://localhost/app), it returns a 403.14-Forbidden: Detailed Error Information: Module: DirectoryListingModule Notification: ExecuteRequestHandler Handler: StaticFile Error Code: 0x00000000 Requested URL: http://localhost:80/test1/ Physical Path: c:\apps\test1\ Logon Method: Negotiate The web application is: Is a very vanilla VS2012 MVC4 Intranet template -- with only a tweak to a label to prove things were working. runs in an Integrated v4.0 application pool setup to use Windows authentication application pool has a custom AD Identity assigned (so it can gain access to a SQL server) application pool identity has read permissions in the c:\apps\test1 folder in which it is running It's an MVC4 application, targeting .NET 4.0 currently -There's no default document in an MVC4 application (like a default.aspx), as there shouldn't need to be one. I don't want to enable directory listings (as that's not the real error). Installed: Roles / Web Server (IIS) / Appliation Development / (.NET 4.5 Extensibility, Application Initialization, ASP.NET 4.5, ISAP Extensions, ISAPI Filters, WebSocket Protocol) Works locally on my machine in IISExpress on Windows 8 Has configured in web.config: <modules runAllManagedModulesForAllRequests="true" /> is set to precompiled during publish When I change the precompiled option to false, the web application does not fail (in my testing at least, it seems to work consistently). The reason I say it's inconsistent is that I've seen it work, then I've published, and the error returns. I can't find a pattern to the issue (and right now, I haven't been able to get it work again, at all). The 403 is returned from a local or remote web browser. I've had trouble finding a solution that isn't intended for older versions of Windows (like suggestions to reinstall ASP.NET which won't work on Windows 2012). I really don't know what else to try.

    Read the article

  • Apache - child process exited with status 255

    - by Brian
    I am running Windows 7 64-bit with an older version of (Apache 2.0.59) and PHP 5.2 - just switched from XP and wanted to keep the same versions. Everything will initially be working fine, but then I'll be trying to load a page and Apache crashes. I'll get an error in the browser that says "The connection to the server was reset while the page was loading." Then Apache stops running. Sometimes it can be restarted, but then crashes again on the next page load. Sometimes it can't even be restarted at all. Looking in the Apache error logs, I see a series of messages that goes something like: [notice] Apache/2.0.59 (Win32) PHP/5.2.13 configured -- resuming normal operations [notice] Server built: Jul 27 2006 15:55:03 [notice] Parent: Created child process 1220 [notice] Child 1220: Child process is running [notice] Child 1220: Acquired the start mutex. [notice] Child 1220: Starting 250 worker threads. [notice] Parent: child process exited with status 255 -- Restarting. I have just come from Win XP where I never had any problems - is this an issue with my Apache version on Win7? Or perhaps it's a configuration issue? Any help would be greatly appreciated, I've done days of research and found nothing helpful. Thanks, Brian

    Read the article

  • squid and ftp connections

    - by Kstro21
    i have a squid proxy server for both, http and ftp connections, i'm trying to use filezilla to open a ftp, but it always fail with an error saying: Status: Connection with proxy established, performing handshake... Response: Proxy reply: HTTP/1.0 403 Forbidden Error: Proxy handshake failed: ECONNRESET - Connection reset by peer Error: Connection timed out Error: Failed to retrieve directory listing i sniff the traffic, and, filezilla is trying to connect to a different port and the proxy denied it look, this is a portion of the sniff result CONNECT 201.150.36.227:61179 HTTP/1.1 Host: 201.150.36.227:61179 User-Agent: FileZilla everytime is a different port, so, no way i can allow it in the squid, also, i set the filezilla to use a active connection, same result, passive connection, same result again, so, i'm out of bullets, and i need your help, maybe a setting in the filezilla or in the squid can do the job, so, give a hand here this is the full log of the filezilla Status: Connecting to uhma.mx through proxy Status: Connecting to 172.19.216.13:3128... Status: Connection with proxy established, performing handshake... Response: Proxy reply: HTTP/1.0 200 Connection established Status: Connection established, waiting for welcome message... Response: 220 ProFTPD 1.3.3a Server (a3 FTP CUATRO) [201.150.36.227] Command: USER uhmamx Response: 331 Password required for uhmamx Command: PASS ******* Response: 230 User uhmamx logged in Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PASV Response: 227 Entering Passive Mode (201,150,36,227,238,251). Command: MLSD Status: Connecting to 172.19.216.13:3128... Status: Connection with proxy established, performing handshake... Response: Proxy reply: HTTP/1.0 403 Forbidden Error: Proxy handshake failed: ECONNRESET - Connection reset by peer Error: Connection timed out Error: Failed to retrieve directory listing

    Read the article

  • Networking stopped working on Ubuntu

    - by 1337Rooster
    I installed Ubuntu 10.04 through the Wubi installer (Funny, I installed it today and thought I would have gotten 10.10). I had a network connection and everything was working fine. I rebooted my coumputer a couple of times and then suddenly, I could not connect to the network and when I click the wireless/networking icon it says "Networking Disabled". I reinstalled Ubuntu and the problem went away. After a few reboots the problem returned. I have tried restarting to see if it would come back as well as a few other things listed below. Any other suggestions would be appreciated. Tried to restart networking via /etc/init.d/networking: amato@ubuntu:~$ sudo /etc/init.d/networking restart * Reconfiguring network interfaces... Ignoring unknown interface eth0=eth0. [ OK ] Tried to stop and start it: amato@ubuntu:~$ sudo /etc/init.d/networking stop * Deconfiguring network interfaces... [ OK ] amato@ubuntu:~$ amato@ubuntu:~$ sudo /etc/init.d/networking start Rather than invoking init scripts through /etc/init.d, use the service(8) utility, e.g. service networking start Since the script you are attempting to invoke has been converted to an Upstart job, you may also use the start(8) utility, e.g. start networking networking stop/waiting Tried start networking: amato@ubuntu:~$ start networking start: Rejected send message, 1 matched rules; type="method_call", sender=":1.58" (uid=1000 pid=2241 comm="start) interface="com.ubuntu.Upstart0_6.Job" member="Start" error name="(unset)" requested_reply=0 destination="com.ubuntu.Upstart" (uid=0 pid=1 comm="/sbin/init")) amato@ubuntu:~$ sudo start networking networking stop/waiting Tried service networking restart: amato@ubuntu:~$ service networking restart restart: Rejected send message, 1 matched rules; type="method_call", sender=":1.60" (uid=1000 pid=2248 comm="restart) interface="com.ubuntu.Upstart0_6.Job" member="Restart" error name="(unset)" requested_reply=0 destination="com.ubuntu.Upstart" (uid=0 pid=1 comm="/sbin/init")) amato@ubuntu:~$ sudo service networking restart restart: Unknown instance: Here are the contents of my /etc/network/interfaces. auto lo iface lo inet loopback I even tried to modify it to this (based on something I read, online, not sure if I was doing the right thing here). Tried everything again and no luck: auto lo eth0 iface lo inet loopback iface eth0 inet dhcp

    Read the article

  • yum not working on EC2 Red Hat instance: Cannot retrieve repository metadata

    - by adev3
    For some reason yum has stopped working in my Amazon EC2 instance, located in the EU West sector. There seems to be something wrong with the path of the repo metadata, is this correct? I would be very grateful for any help, as my experience in this field is somewhat limited. Thank you very much. cat /etc/redhat-release: Red Hat Enterprise Linux Server release 6.2 (Santiago) yum repolist: Loaded plugins: amazon-id, rhui-lb, security https://rhui2-cds01.eu-west-1.aws.ce.redhat.com/pulp/repos//rhui-client-config/rhel/server/6/x86_64/os/repodata/repomd.xml: [Errno 14] PYCURL ERROR 22 - "The requested URL returned error: 401" Trying other mirror. https://rhui2-cds02.eu-west-1.aws.ce.redhat.com/pulp/repos//rhui-client-config/rhel/server/6/x86_64/os/repodata/repomd.xml: [Errno 14] PYCURL ERROR 22 - "The requested URL returned error: 401" Trying other mirror. repo id repo name status rhui-eu-west-1-client-config-server-6 Red Hat Update Infrastructure 2.0 Client Configuration Server 6 0 rhui-eu-west-1-rhel-server-releases Red Hat Enterprise Linux Server 6 (RPMs) 0 rhui-eu-west-1-rhel-server-releases-optional Red Hat Enterprise Linux Server 6 Optional (RPMs) 0 repolist: 0 yum update: (I needed to remove the base URLs below because of ServerFault's restrictions for new users) Loaded plugins: amazon-id, rhui-lb, security [same as base url 1 above]/pulp/repos//rhui-client-config/rhel/server/6/x86_64/os/repodata/repomd.xml: [Errno 14] PYCURL ERROR 22 - "The requested URL returned error: 401" Trying other mirror. [same as base url 2 above]/pulp/repos//rhui-client-config/rhel/server/6/x86_64/os/repodata/repomd.xml: [Errno 14] PYCURL ERROR 22 - "The requested URL returned error: 401" Trying other mirror. Error: Cannot retrieve repository metadata (repomd.xml) for repository: rhui-eu-west-1-client-config-server-6. Please verify its path and try again

    Read the article

  • SChannel "cannot find certificate in either LocalMachine or CurrentUser store"

    - by Chris J
    We have an in-house application that requires the use of client SSL certificates to authenticate with a remote server (not under our control). This has worked without problems before but on deploying to a new server, we're having problems getting Windows 2008 to use the certificate. The certificate exists as a .pfx file that contains a private key. The same certificate exists in the LocalMachine store, again with its private key. We've ensured the one in the LocalMachine store is correct by creating a website in IIS against that certificate, so we're happy that the certificate, certificate chain, and private key is valid. The PFX has been created by exporting from the Certificates MMC snap-in. The issue is that we get the following in the system diagnostic logs that suggests it can't find the private key: System.Net Information: 0 : [5988] SecureChannel#23264094 – Locating the private key for the certificate: [Subject] CN=internal-server.company.com, OU=Servers, OU=Devices, O=org [Issuer] CN=SubCA02, OU=CA, o=org [Serial Number] 407ABCDE [Not Before] 31/10/2013 11:08:48 AM [Not After] 31/10/2016 11:08:48 AM [Thumbprint] 4354A34F6004F019E60F055979A47E50F62D1504 . System.Net Information: 0 : [5988] SecureChannel#23264094 – Cannot find the certificate in either the LocalMachine store or the CurrentUser store. I've validated the thumbprint, issuer and serial number listed in the log with the certificate in the LocalMachine store and these marry up. From what I can tell with much searching, this appears to be a permissions issue. The user the application is running as has been granted access to the private key (Personal Certificates - right click on the certificate - all tasks - Manage Private Keys), so I'm now at a loss as to which permission(s) it may be that is causing the issue.

    Read the article

  • Cannot create a project TFS 2012 - TF218027

    - by GrandMasterFlush
    I've just installed TFS2012 and am trying to create a new project in the default collection via Visual Studio 2012 but I keep getting this error message: TF218027: The following reporting folder could not be created on the server that is running SQL Server Reporting Services: /TfsReports/DefaultCollection. The report server is located at: http://<servername>/Reports. The error is: The permissions granted to user '<domain>/grandmasterflush' are insufficient for performing this operation.. Verify that the path is correct and that you have sufficient permissions to create the folder on that server and then try again. I've checked the permissions and my user is a member of the Project Collection Administrators and the Project Collection Administrators group has the 'Create new project' permission set to allow. The only thing I think it might be is that the user that I created during installation for the Sharepoint access and reports viewing does not have permission to write to the reports folder, however if I select "Do not configure a SharePoint site at this time" then I still get the error messages. I can't find the reports folder to check the permissions either. TFS is using an instance of SQL 2012 that was already on the machine when TFS was installed. Can anyone see what I'm doing wrong please?

    Read the article

  • High CPU usage by 'svchost.exe' and 'coreServiceShell.exe'

    - by kush.impetus
    I am having a laptop running on Windows 7 Ultimate 32-bit. Since past few days, my laptop is facing a serious problem. Whenever I connect to Internet, either svchost.exe or coreServiceShell.exe or both hog the CPU. The coreServiceShell.exe consumes a lot of RAM also. Going into the details, I found that high CPU usage of svchost.exe is caused by Network Location Awareness service. And the high CPU usage of coreServiceShell.exe is caused by Trend Micro Titanium Internet Security 2012. That kind'a makes me think that Trend Micro may be the root of the problem. After further testing, I found that if I use IE or Firefox to browse the Internet, immediately after connecting to Internet, things are normal. See and But if I use Google Chrome, the coreServiceShell.exe hogs both CPU and RAM. At this point, if I disconnect the Internet, the CPU and RAM usage by coreServiceShell.exe continues to be high till I close the Chrome. Also, when I close the Chrome, while Internet is connected, svchost.exe continues to hog CPU but coreServiceShell.exe leaves the race. That makes think that Chrome is the root of the problem, but again, tracing coreServiceShell.exe takes me back to Trend Micro Internet Security. Stopping the Protection by the Trend Micro Internet Security doesn't help either (I am not able to stop its services though). I have updated the Chrome, but no help. I just can't figure out who is the culprit. I can't do without the Google Chrome (of course, by not using it) because of its immensely useful and indispensable features both during browsing and development. Secondly, I can't uninstall the Trend Micro Internet security Suite since it still has few months before it expires and is proving me reliable protection. What could be the cause of the problem and what can I do to resolve this? Thanks in advance

    Read the article

  • Word 2010 Crashing

    - by Flymo
    We have an office with all users using the same spec'ed PCs with the same Image deployed to them, so that the software and configuration is identical. I have one user whos keeps having the install of MS Word 2010 crash intermittently. First i reinstalled Office 2010 Suite, but will have the crashes. The PC has been replaced with a clean install of Windows and Office but we are still having the issues with Word crashing. We have had the user to log onto another PC which we know to be working fine, but again, Word keeps crashing. Below is the Error from EventViewer: Faulting application name: WINWORD.EXE, version: 14.0.6024.1000, time stamp: 0x4d83e310 Faulting module name: MSVCR90.dll, version: 9.0.30729.6161, time stamp: 0x4dace5b9 Exception code: 0xc0000417 Fault offset: 0x000320f0 Faulting process id: 0xc34 Faulting application start time: 0x01cd1881ea917c33 Faulting application path: C:\Program Files\Microsoft Office\Office14\WINWORD.EXE Faulting module path: C:\Windows\WinSxS\x86_microsoft.vc90.crt_1fc8b3b9a1e18e3b_9.0.30729.6161_none_50934f2ebcb7eb57\MSVCR90.dll Report Id: edd97602-8477-11e1-aa13-001111db42bf The PC is running Windows 7 Professional and Office 2010 We have tried everything we can think of. If anyone could enlighten us, it would be very much appretiated. Cheers

    Read the article

  • Intermittent Windows Server 2008 BSOD and restart

    - by Timka
    Our EC2 Instance (Windows Server 2008) crashed multiple times for the past 3 months (last time was today at 1:05 EST). Upon reviewing MEMORY.DMP file we noticed that possible cause of the crashes is rhelnet.sys (RedHat PV NIC Driver). Server's Event Viewer has the following records right after the crash: Critical - Kernel Power: The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. BugCheck: The computer has rebooted from a bugcheck. The bugcheck was: 0x000000d1 (0x000000000000002d, 0x0000000000000002, 0x0000000000000000, 0xfffff88001402d14). A dump was saved in: C:\Windows\MEMORY.DMP. Report Id: 100113-35849-01. Could this be a hardware issue? Would it help if we stop and start the instance? Or is this more likely that this is caused by the software running on the system? [Update 10.01.2013] Amazon Rep suggested to update RH drivers to Citrix PV drivers on our instance: Upgrading PV Drivers [Update 10.08.2013] We performed a drivers upgrade on the cloned instance. Right after the upgrade we noticed the following errors in our Event viewer: Xennet6 errors in Event Viewer (Event ID# 5001) After digging a bit more I found this article suggesting to install the latest Citrix drivers. Unfortunately, this didn't help us at all and our cloned instance became unresponsive. [Update 10.08.2013 2] I recreated an instance and updated PV drivers again. After searching on Internet I found this article where Amazon Rep explains that: "Event ID 5001 from source Xennet6 cannot be found" message does not indicate anything wrong, just that the PV driver is looking for a feature that we have not implemented in our version of Xen. I will keep my test system running for a while to see if there any issues with it.

    Read the article

  • How to install OS X *.TTC font on Windows? Error: "*.TTC does not appear to be a valid font"

    - by Chris W. Rea
    I own both a Mac running OS X 10.6 Snow Leopard, and a PC running Windows 7. On my Mac is a font called "AmericanTypewriter.ttc". I'd like to use that font on my PC, for a specific creative project. I was able to copy the actual font file over to the PC, but when I try to install it into the Windows Fonts folder I get the following error message: "Cannot install (FONTNAME).ttc - The file '(FONTNAME).ttc' does not appear to be a valid font." Can *.TTC format font files be installed on Windows? If so, how? Thanks! UPDATE: I downloaded the source code for a simple ttc2ttf utility (ttc2ttf_AA.tar.gz) found at this Japanese page and compiled it under cygwin via g++. The resulting executable extracted a single file, "AmericanTypewriter.ttf", from the TTC / True Type Collection. (Why have a collection with only one file!?) However, I still get an error message similar to the one above when I try to install the resulting AmericanTypewriter.ttf onto Windows. I'm stumped again. p.s. I no longer need this font on Windows, but now I'm determined to figure out why & how-to :-)

    Read the article

  • What exactly is a Mobile mouse? + Mouse Recommendation

    - by chobo2
    I am really disappointed with Logitech. My first cordless wireless mouse was from them and it lasted like 5 years. So I decided to get another one from them http://www.futureshop.ca/catalog/proddetail.asp?logon=&langid=EN&sku_id=0665000FS10099373&catid= And this mouse sucks bad. After 6 months it broke. I returned it under warranty and got a new one now 4-6 month later it is on the verge of breaking again.... You pay like $50 for this mouse and it lasts like 6 months that sad. I just lost faith in Logitech mice as I remember my bro also had a logitech mouse too and it broke after like 6 months. He then bought another logitech mouse(different model) that has been working for maybe 2 years(and no signs of breaking) but I am not crazy about the mouse(I don't like the 2 buttons by the wheel) and I not sure if they even sell it(maybe they got rid of it because it lasts too long). http://www.tigerdirect.ca/applications/SearchTools/item-details.asp?EdpNo=1578495&CatId=1285 So I am looking at a Microsoft mouse. http://www.futureshop.ca/catalog/proddetail.asp?logon=&langid=EN&sku_id=0665000FS10125565&catid= I am looking at this one but I am not sure what they mean by mobile mouse. I think that is what MS calls notebook mice. So I am not sure if this would be a good mouse to get for a desktop. I see it uses like a micro usb receiver but I am not sure if it is smaller then a standard mouse. But almost all the mice I looked at at futureshop.ca or staples are labeled notebook mice or mobile mice. So not sure what mice would be right for me. I don't want a corded one though. I really liked the LX6 design alot but it can't last more than 6 months. Thanks

    Read the article

  • "file not found" error while commiting

    - by AntonAL
    I have a working copy, checked out from SVN repository. When i'm trying to commit, i get following error: svn: File not found: revision 57, path '/trunk/path/to/my/file/logo-mini.jpg' I've found this file in the repo and noticed, that it has only one revision - 58. I don't understand, why SVN complains about this file, when it is presented and why it points to revision 57 instead of 58 ? I've also renamed the grand-grand-grand-parent folder of this file. Possible, this is an issue ... Update Detailed error description, that i've got from Cornerstone app (Mac OS X): Description : Could not find the specified file. Suggestion : Check that the path you have specified is correct. Technical Information ===================== Error : V4FileNotFoundError Exception : ZSVNNoSuchEntryException Causal Information ================== Description : Commit failed (details follow): Status : 160013 File : subversion/libsvn_client/commit.c, 867 Description : File not found: revision 57, path '/trunk/assets/themes/base/article-content/images/logo-mini.jpg' Status : 160013 File : subversion/libsvn_fs_fs/tree.c, 663 So, i've renamed "/trunk/assets/themes directory" to "/trunk/assets/skins", while improving project structure. I've tried following: updating /trunk/assets/themes directory cleaning deleting from filesytem and checking out again reverting entire /trunk/assets/themes directory to the HEAD revision. Even this does't helps. Still getting the same error. I've got no results.

    Read the article

  • "0x80004005: Unspecified error" when renaming folders in Windows 7

    - by Michael Steele
    Setup I've just installed Windows 7 Ultimate 64bit. The operating system is installed on an 80GB Intel X-25M. I have a secondary 500GB Barracuda 7200.12 to be used for storage. This second drive is mounted as 'G'. Problem I'm getting an error whenever I try to rename a folder within this drive. The error says: An unexpected error is keeping you from renaming the folder. If you continue to receive this error, you can use the error code to search for help with this problem. Error 0x80004005: Unspecified error Clicking the "Try Again" button gets past the error, and correctly renames the folder. If I create a folder and leave it's name as "New Folder", then I don't see an error. I'm also able to manipulate files however I want without seeing an error. Things I've Tried Changing permissions on the drive Reformatting the drive. I've tried using both a "Basic" and "Dynamic" partition table. Checking the drive for errors using Microsoft tools Things I've Not Yet Tried When I first installed Windows I was given a choice between three types of partitions to use. I no longer remember what the choices were or what I selected. One was a GUID partition table, one was a traditional MBR, and I can't remember the third option.

    Read the article

  • Smart Array P400 - Accelerator Replacement Battery Failure

    - by inflammable
    TL;DR - Is the immediate failure of a replacement battery, for a failed battery, on a battery backed accelerator for a Smart Array P400 controller a common occurrence? Or are we likely to have an storage controller with an impending and critical fault? We have a slightly confusing situation with a Smart Array P400 storage controller with the 512mb battery backed accelerator addon on an HP DL380 server. The storage controller is (afaik) running the latest firmware and driver: Model: Smart Array P400 Controller Status: OK Firmware Version: 7.24 Serial Number: *snip* Rebuild Priority: Medium Expand Priority: Medium Number Of Ports: 2 The storage diagnostic (both on the both boot-up screen for the controller and within the 'Management Homepage' and the 'HP Array Diagnostic Utility') recently starting showing the following status a fault for the battery for the accelerator: Accelerator Status: Temporarily Disabled Error Code: Cache Disabled Low Batteries Serial Number: *snip* Total Memory: 524288 KB Read Cache: 25% Write Cache: 75% Battery Status: Failed Read Errors: 0 Write Errors: 0 We replaced the battery with a new unit (a visual inspection of the P400 card showing nothing unusual) and saw the same fault - but expected this to disappear over the course of a few hours/days as it charged. This didn't happy, and the fault status remains the same as above. Given the battery is a genuine part from HP, I wouldn't have expected a replacement battery to fail straight away, or to be dead-on-arrival (is that naivety on my part?). Is the immediate failure of a replacement battery, for a failed battery, on a battery backed accelerator a common occurrence? Or are we likely to have an storage controller with an impending and critical fault? Is there any diagnostic that could tell me more about the failed battery, without cracking the server open again? Many thanks!

    Read the article

  • centos yum problems

    - by Malachi Soord
    I am really new to using linux and have just formatted my centos 5.2 vps and am trying to install links by using the command yum install links. But the following error gets displayed: [root@inverses ~]# yum install links Loading "fastestmirror" plugin Loading mirror speeds from cached hostfile * lxlabsupdate: download.lxlabs.com * lxlabslxupdate: download.lxlabs.com * base: ftp.nluug.nl * updates: distrib-coffee.ipsl.jussieu.fr * addons: mirror.answerstolove.com * extras: distrib-coffee.ipsl.jussieu.fr http://ftp.nluug.nl/ftp/pub/os/Linux/distr/CentOS/5.2/os/i386/repodata/repomd.xml: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://distrib-coffee.ipsl.jussieu.fr/pub/linux/centos/5.2/os/i386/repodata/repomd.xml: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://mirror.ukhost4u.com/centos/5.2/os/i386/repodata/repomd.xml: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://centosh2.centos.org/centos/5.2/os/i386/repodata/repomd.xml: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://mirror.atrpms.net/centos/5.2/os/i386/repodata/repomd.xml: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://centosf.centos.org/centos/5.2/os/i386/repodata/repomd.xml: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://centoso3.centos.org/centos/5.2/os/i386/repodata/repomd.xml: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://centosk.centos.org/centos/5.2/os/i386/repodata/repomd.xml: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://centosv.centos.org/centos/5.2/os/i386/repodata/repomd.xml: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://centosk3.centos.org/centos/5.2/os/i386/repodata/repomd.xml: [Errno 14] HTTP Error 404: Not Found Trying other mirror. Error: Cannot retrieve repository metadata (repomd.xml) for repository: base. Please verify its path and try again From what I gather after checking out some of the URLs to see if they exist or not is that they require a redirect from .../5.2/.. to just ../5/ Is this a common thing to have to change? and how could I change this? Here is my CentOS-Base.repo http://pastebin.com/m67c1a022

    Read the article

  • WmiPrvSE memory leak on Windows 2008 *R2*

    - by MichaelGG
    I've seen references on Windows 2008 to WmiPrvSE leaks, but nothing about Windows 2008 R2. We're running R2 on top of Hyper-V (2008). We are also running NSClient++ for monitoring from opsview. Over time, WmiPrvSE.exe starts to use a lot of memory, causing memory alert issues (less than 10% free). VM has 2GB, WmiPrvSE consumes up to 500-600MB before I kill it. Killing the process doesn't seem to have any negative effect; it starts up again and I haven't noticed any problems. But after a day or two, it's back in the same situation. Any ideas on what to do? Resource Monitor doesn't show any Disk or Network IO by WmiPrvSE.exe. Just slowly climbing private memory... Edited to add: We aren't running clustering, or Windows System Resource Manager. The only regular WMI user I can guess is NSClient++, but we don't seem to have this problem on other servers.

    Read the article

  • Cannot bind OSX to AD

    - by erotsppa
    I'm trying to get an mac mini running snow leopard server to join a windows domain here. The windows domain server is running Windows server 2008. When I go to "Accounts" in my System Preferences, and lick on "Join", I get this error: "Unable to add server. Node name wasn't found. (2000)" In my console messages I find this: 10-04-06 11:42:25 AM System Preferences1452 -[ODCAddServerSheetController handleOtherActionError: gotError: Error Domain=com.apple.OpenDirectory Code=2000 UserInfo=0x2004f2f80 "Custom call 82 to Active Directory failed.", Node name wasn't found. I specified a FQDN for the domain server, so I am totally confused as to why it would list "domain = com.apple...." in that error. I've tried firing up the Directory Utility and trying to join a domain via the Active Directory option there. Again I fill in the FQDN, and the proper administrator/password acount info. Now I get a different error: "Invalid Domain An invalid Domain and Forest combination was specified. You should enter a fully qualified DNS name for the domain and forest (e.g., ads.company.com)." If anyone has any pointers or suggestions this would be appreciated.

    Read the article

  • Problems setting NTP sever with w32tm for a DC that is a Hyper-V guest

    - by R.Tonheim
    Hello ! I have tried to sett my DC to get its time from several NTP severs. I follow this answer (http://serverfault.com/questions/24298/w32time-sync-problems-for-hyper-v-guests-w32time-event-ids-38-24-29-35/24299#24299) to do it. First I disable Time Synchronization in the Hyper-V Integration Services for each guest. Then restart the Windows Time serviceon the guest. I had before this used this command: w32tm /config /manualpeerlist:"ntp.uio.no;timekeeper. uio.no;nissen.uio.no;0.no.pool.ntp.org;1.no.pool.ntp.org;2.no.pool.ntp.org" /syn cfromflags:manual /reliable:yes /update And the cmd sad: The command completed successfully. But the time was still 10 min wrong... I run w32tm again after restarted the DC without it having any effect. The w32tm /query /status still say: "Source: Local CMOS Clock" FROM MY CMD: Microsoft Windows [Version 6.0.6002] Copyright (c) 2006 Microsoft Corporation. All rights reserved. C:\Users\Administrator.MHGw32tm /query /status Leap Indicator: 0(no warning) Stratum: 1 (primary reference - syncd by radio clock) Precision: -6 (15.625ms per tick) Root Delay: 0.0000000s Root Dispersion: 10.0000000s ReferenceId: 0x4C4F434C (source name: "LOCL") Last Successful Sync Time: 05.09.2009 20:06:21 Source: Local CMOS Clock Poll Interval: 6 (64s) C:\Users\Administrator.MHGw32tm /config /manualpeerlist:"ntp.uio.no;timekeeper. uio.no;nissen.uio.no;0.no.pool.ntp.org;1.no.pool.ntp.org;2.no.pool.ntp.org" /syn cfromflags:manual /reliable:yes /update The command completed successfully. C:\Users\Administrator.MHGw32tm /query /status Leap Indicator: 0(no warning) Stratum: 1 (primary reference - syncd by radio clock) Precision: -6 (15.625ms per tick) Root Delay: 0.0000000s Root Dispersion: 10.0000000s ReferenceId: 0x4C4F434C (source name: "LOCL") Last Successful Sync Time: 05.09.2009 20:06:21 Source: Local CMOS Clock Poll Interval: 6 (64s) C:\Users\Administrator.MHG

    Read the article

  • Problem with XLSX file on Office 2003 with Compatibility Pack

    - by MadBoy
    I've this machine which has Office 2003 installed with Compatibility Pack. User received one file which she has to work with in XLSX format (file has to stay in that format so options to save it as XLS can be skipped). When she opens the file from Desktop or any other location it gives an error like "Cannot find the file in following location" and in the background it starts Converting XLSX file to XLS. In the end Excel is opened up with some random file name X000008.xls (Read Only) which is just 1 to 1 conversion of the XLSX document. However if I go directly to Excel and use File / Open and try to open the XLSX file no error or conversion is done. The file is writable and can be saved in XLSX format. The file name is simple like This_file something.XLSX, I've even tried to remove all spaces but it gave no better results. Anyone has any recommendations? So far I have done: 1. Uninstalled Compatibility Pack and installed it again. Tried opening it without any other updates and the error still pops out. In progress: I am now running all possible updates of office (like 5 of them) which i suppos won't fix anything (as they were applied when I've uninstalled compatibility pack). Next in run will be (not yet done) installing Windows XP SP3. What other things I can do?

    Read the article

  • Windows 7 intermittently drops wired internet/lan connection.

    - by CraigTP
    In a nutshell, my Windows 7 Ultimate PC intermittently drops it's internet connection. Why? Background: My PC is wired to my ADSL modem/router which is directly connected to the phone line. I also have wireless connectivity turned on within the router for a laptop to connect wirelessly. Every few hours or so, when using my PC, I find I cannot access the internet and pages will not load. Eventually, Windows7 will update the network icon in the task-tray to show the exclamation mark symbol on the network icon. Opening up the Network And Sharing Centre will show the red cross between the "Multiple Networks" and "The Internet". Here's a picture of the "Network And Sharing Centre" (grabbed when everything was working!) As you can see, I'm running Sun's VirtualBox on this machine and that creates a Network connection for itself. This doesn't seem to affect the intermittent dropping (i.e. the intermittent drops occur whether the VirtualBox connection is in use or not). When the connection does drop, I cannot access any internet pages, nor can I access the router's web admin page at http://192.168.1.1/, so I'm assuming I've lost all local LAN access too. It's definitely not the router (or the internet connection itself) as my laptop, using the wireless connection (and running Vista Home Premium) continues to be able to access the internet (and the router's web admin pages) just fine. Every time this happens, I can immediately restore all internet and LAN access by opening Network Adapter page, disabling the "Local Area Connection" and then re-enabling it. Give it a few seconds and everything is fine again. I assume this is because, beneath the GUI, it's effectively doing an "ipconfig /release" then "ipconfig /renew". Why does this happen in the first place, though? I've googled for this and seen quite a few other people (even on MSDN/Technet forums) experiencing the same or almost the same problem, but with no clear resolution. Suggestions of turning off IPv6 on the LAN adapter, and ensuring there's no power management "sleeping" the network adapter have been tried but do not cure the problem. There does not seem to be any particular sequence of events that cause it to happen either. I've had it go twice in 20 minutes when just randomly browsing the web with no other traffic, and I've also had it go once then not go again for 2-3 hours with the same sort of usage. Can anyone tell me why this is happening and how to make it stop? EDIT: Additional information based upon the answer provided so far: Firstly, I forgot the mention that this is Windows 7 64 bit if that makes any difference at all. I mentioned that I don't think the VirtualBox network adpater is causing this problem in any way, and I also have VirtualBox installed on two other machines, one running Vista Home Premium and the other running XP. Neither of these machine experience the same network connectivity issues as the Windows 7 machine. The IP assignment for the Windows 7 machine is the same both before and after the "drop". I have a DHCP server on the router issuing IP Addresses, however my Windows 7 machine uses a static address. Here's the output from "ipconfig": Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.2(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Within the system's event logs, the only event that relates to the connection dropping is a "DNS Client Event" and this is generated after the connection has dropped and is an event detailing that DNS information can't be found for whatever website I may be trying to access, just as the connection drops: Log Name: System Source: Microsoft-Windows-DNS-Client Event ID: 1014 Task Category: None Level: Warning Keywords: User: NETWORK SERVICE Description: Name resolution for the name weather.service.msn.com timed out after none of the configured DNS servers responded. The network adapter chipset is Realtek PCIe GBE Family Controller and I have confirmed that this is the correct chipset for the motherboard (Asus M4A77TD PRO), and in fact, Windows Update installed an updated driver for this on 12/Jan/2009. The details of the update say that it's a Realtek software update from December 2009. Incidentally, I was still having the same intermittent problems prior to this update. It seems to have made no difference at all. EDIT 2 (1 Feb 2010): In my quest to solve this problem, I have discovered some more interesting information. On another forum, someone suggested that I should try running Windows in "Safe Mode With Networking" and see if the problem continues to occur. This was a fantastic suggestion and I don't know why I didn't think of it sooner myself. So, I proceeded to run in Safe Mode with Networking for a number of hours, and amazingly, the "drops" didn't occur once. It was a positive discovery, however, due to the intermittent nature of the original problem, I wasn't completely convinced that the problem was cured. One thing I did note is that the fan on my GFX card was running alot louder than normal. This is due to the fact that I have an ASUS ENGTS250 graphics card (http://www.asus.com/product.aspx?P_ID=B6imcoax3MRY42f3) which had a known problem with a noisy fan until a BIOS update fixed the issue. (See the "Manufacturer Response" here: http://www.newegg.com/Product/Product.aspx?Item=N82E16814121334 for details). Well, running in safe mode had the fan running (incorrectly) at full speed (as it did before the BIOS update), but with an (apparently) stable network connection. Obviously some driver was not loaded for the GFX card when in Safe Mode so this got me thinking about the GFX card (since the very noisy fan was quite obvious when running in Safe Mode). I rebooted into normal mode, and found that Nvidia had a very up-to-date new driver for my GFX card (only about 1 week old), so I downloaded the appropriate driver and installed it. After installation and a reboot, I was able to use my PC for an entire day with NO NETWORK DROPS!!! This was on Saturday. However, on the Sunday, I also had my PC for pretty much the entire day and experienced 2 network drops. No other changes have been made to my PC in this time. So, the story seems to be that updating my graphics card drivers seems to have improved (if not completely fixed) the issue, however, I'm still searching for a proper fix for this problem. Hopefully, this information may help anyone who may have additional ideas as to why this problem is occuring in the first place. (And why does new GFX card drivers have anything to do with the network?) I appreciate everyone's feedback so far. However, I'll have to ask once more if anyone has any further ideas of how to fix this particular problem? Thanks in advance.

    Read the article

  • powershell v2 remoting - How do you enable unecrypted traffic

    - by Peter Walke
    I'm writing a powershell v2 script that I'd like to run against a remote server. When I run it, I get the error : Connecting to remote server failed with the following error message : The WinRM client cannot process the request. Unencrypted traffic is currently disabled in the client configuration. Change the client configurati on and try the request again. For more information, see the about_ Remote_Troubleshooting Help topic. I looked at the online help for about _ Remote_Troubleshooting, but it didn't point me towards how to enable unecrypted traffic. Below is the script that I'm using that is causing me problems. Note: I have already run Enable-PSRemoting on the remote machine to allow it to accept incoming requests. I have tried to use a session option variable, but it doesn't seem to make any difference. $key = "HKLM:\SOFTWARE\Microsoft\PowerShell\1\ShellIds" Set-ItemProperty $key ConsolePrompting True $tvar = "password" $password = ConvertTo-SecureString -string $tvar -asPlainText –force $username="domain\username" $mySessionOption = New-PSSessionOption -NoEncryption $credential = New-Object System.Management.Automation.PSCredential($username,$password) invoke-command -filepath C:\scripts\RemoteScript.ps1 -sessionoption $mySessionOption -authentication digest -credential $credential -computername RemoteServer How do I enable unencrypted traffic?

    Read the article

< Previous Page | 479 480 481 482 483 484 485 486 487 488 489 490  | Next Page >