Search Results

Search found 34836 results on 1394 pages for 'off the shelf software'.

Page 483/1394 | < Previous Page | 479 480 481 482 483 484 485 486 487 488 489 490  | Next Page >

• How harmful is a hard disk spin cycle?

  - by Gilles

  It is conventional wisdom¹ that each time you spin a hard disk down and back up, you shave some time off its life expectancy. The topic has been discussed before: Is turning off hard disks harmful? What's the effect of standby (spindown) mode on modern hard drives? Common explanations for why spindowns and spinups are harmful are that they induce more stress on the mechanical parts than ordinary running, and that they cause heat variations that are harmful to the device mechanics. Is there any data showing quantitatively how bad a spin cycle is? That is, how much life expectancy does a spin cycle cost? Or, more practically, if I know that I'm not going to need a disk for X seconds, how large should X be to warrant spinning down? ¹ But conventional wisdom has been wrong before; for example, it is commonly held that hard disks should be kept as cool as possible, but the one published study on the topic shows that cooler drives actually fail more. This study is no help here since all the disks surveyed were powered on 24/7.

  Read the article

• Diagnosing SAN connectivity issues (RHEL5)

  - by Matthew

  We are currently utilizing GFS2 to share a SAN LUN between 3 servers. However due to a feature problem with vendor software we are using, we currently have the volume unmounted on two of the boxes, and are instead exporting the GFS2 filesystem via NFS from the first one (the software requires some weird locking mechanics that GFS2 doesn't support). As of this morning, NFS was no longer able to read/write to the volume from any of the servers, including the NFS server. I then tried checking the normal mount (the directory that is exported on the NFS server) and I received a weird input/output error just trying to CD into it. When I tried running multipath, I got a DM error, however multipath -l worked just fine. I tried unmounting the GFS2 volume, and the CLI hung. I ran init 0 which killed most services, but then the shutdown appeared to have been hung. I logged in via out of band access (hp ILO) and saw that the shutdown was hung trying to unmount GFS2 volumes. My main priority was getting the box back online so after about 5 minutes of waiting I did a hard reset. I am now trying to figure out what went wrong. What are the correct logs to investigate? I've never run into SAN issues like this before. The SAN is connected via 2 fibre connections. Any help would really be appreciated. Everything appears to be up and functional now.

  Read the article

• NetApp NDMP backup with BE 2010 R2 works, restore fails

  - by uuwe

  Hi, I'm having some issues with a new Backup Exec 2010 R2 installation. I configured a NetApp FAS2020 as an NDMP device and want to backup files from the NAS to a tape drive connected to my backup server. I set up ndmpd according to this document (http://www.symantec.com/business/support/index?page=content&id=TECH48957) and created a separate backup user (http://filers.blogspot.com/2006/09/setting-veritas-netbackup-with-non.html). Backup works perfectly, but restoring any file gives me an authentication failed error. The NDMP device has a "global" ndmp user configured in the device tab (tried this with the newly created ndmpd backup user and the netapp root) and I can also configure separate resource credentials in the BE restore job. I have tried setting the same accounts for the "global" ndmp device and the restore credentials and have also tried setting different accounts for them. NDMP debug level is at 5 and this is what shows up in /etc/messages. The session is closed immediately after it has been granted. 16:12:07 PST [Java_Thread:info]: ndmpdserver: ndmpd.access allowed for version = 4, sessionId = 51, from src ip = 192.168.11.17, dst ip = FAS2020-1/192.168.11.75, src port = 50857, dst port = 10000 16:12:07 PST [Java_Thread:info]: Ndmpd51: ndmpd session closed successfully for version = 4, sessionId = 51, from src ip = 192.168.11.17, dst ip = FAS2020-1/192.168.11.75, src port = 50857, dst port = 10000 Running wireshark on the backup server doesn't produce much. It shows a SYN - SYN/ACK - NDMP CONNECT_CLOSE Request from the backup server. The Resource Credentials for the restore job behave very oddly. If I enter NDMP credentials and do "Test All" it fails. If I use my regular domain backup account, it is successful. There are no failed or succeeded logons in the NetApp ndmp log and tracing this check shows that it doesn't even connect to the NAS. This makes me think that this is more likely flaky BE behaviour rather than misconfiguration of the NAS. Here is the options ndmp output: FAS2020-1 options ndmp ndmpd.access all ndmpd.authtype challenge ndmpd.connectlog.enabled on ndmpd.enable on ndmpd.ignore_ctime.enabled off ndmpd.offset_map.enable on ndmpd.password_length 16 ndmpd.preferred_interface disable ndmpd.tcpnodelay.enable off

  Read the article

• Sorting/grouping when there are multiple values in one cell

  - by ngm

  I have an Excel 2007 spreadsheet, where each row of the dataset describes a feature of a piece of software. One of the columns in the spreadsheet is Relevant Users, which describes which users of the software the feature is of interest to. There may be a couple of different users interested in a feature, in which case I've been filling in the cell with the two user types separated by a colon, e.g. 'Usertype A; Usertype D'. Occassionally, I'd like to sort my data by the Relevant Users column. However, the way I'm populating the column means the sorting isn't very smart. If I have a feature where 'Relevant Users' is 'Usertype A; Usertype D', and then I sort by Relevant Users, that feature will be grouped at the end of all the other features of relevant to Usertype A, as it's just sorting alphabetically. But I want it to be listed in the two separate groups of Usertype A and Usertype D. Or, if I have a pivot table that groups the features together under the heading of Relevant User, I'll get all the features for 'Usertype A', then 'Usertype B', then 'Usertype C', then 'Usertype D', then 'Usertype A; Usertype D', etc. Whereas I really want a feature with Relevant Users as 'Usertype A; Usertype D' to show up in both the Usertype A group and the Usertype D group. I guess if this information was in a database I might have a many-to-many table linking Relevant Users to features. But is there a way to go about having this kind of many-to-many relationship in Excel?

  Read the article

• Migrate Domain from Server 2008 R2 to Small Business Server 2011

  - by josecortesp

  I'm looking for some advice here, rather than the big how to do it I'm looking for what do to I have this home server, quad core and 4 GB of ram (I really can't afford more right now). With a Windows Serve 2008 R2 With ActiveDirectory and a Hyper-V-Virtual machine with SharePoint, TFS and a couple of more thigs. I have a least 10 remote users, all of them joined a Hamachi VPN (working great by the way). But I want to migrate that to a Small Business Server 2011 Standard. I tried to make a VM to join the domain and then promote that VM, back up it and then format the physical server, boot up the VM, Promote the Phisical and then erase the VM, but I can't do that because of SBS requiring a least 4 GB of ram to install (so I can't give all the 4 GB of physical ram to a VM). I was thinking in using a laptop (All the clients are laptop) as a temporal server, join the domain, promote it, then format the server and install SBS on the server and do all again. I really need some advice. Thanks in advance. BTW, I know that the software I'm using is kindda expensive, and I can't afford more hardware. I have access to MS downloads by a University partnership so I have all this software for free.

  Read the article

• Computer won't boot from a bootable DVD

  - by JohnB

  My friend gave me his old computer that used to have WinXP on it. I'm trying to load Win7 on it and I thought there was something wrong because it wouldn't boot off a bootable disc, even though I setup the BIOS boot settings properly (I've done this sort of thing a million times). However, this closely related post helped me realize that I can boot off a bootable CD (WinXP), just not a DVD (Win7) Computer won’t boot from CD/DVD drive That might be the answer to my question, however, this motherboard is still pretty current technology. It's a good quality Gigabyte board, and judging from this product page, it came out in 2004. If I can't figure out a solution to my DVD boot problem, I'll have to try something like this: Boot and Install Windows from a USB thumb drive I guess it's possible that this motherboard doesn't allow booting from a DVD, but I still think that I might be missing something. It wouldn't be the DVD rom drive would it? I did try another drive and had the same results. However, I didn't try booting a DVD in the computer that the other test drive came out of, I'll do that later today. Any other advice? Thanks.

  Read the article

• how to properly set environment variables

  - by avorum

  I've recently started using Windows (having used Ubuntu up until now) and I find myself unable to properly set environment variables. Whenever I set them they don't seem to work. I've been going to Start-Edit Environment Variables for your Account and editing the PATH value in the upper half of the GUI. Here's what I've got so far. ;C:\Chocolatey\bin;C:\tools\mysql\current\bin;C:\Program Files (x86)\Git\bin;C:\Program Files\MySQL\MySQL Server 5.6\bin\;C:\Python33\Scripts; These are each the parent directories of the executables I'd like to be able to run by name from CMD, but mysql, git, and pip aren't being recognized. Am I doing something wrong syntactically or at a general understanding level? I'd like to be able to run these commands without having to specify the full path to the executables every time. EDIT: The full PATH extracted from CMD PATH=C:\Python33\;C:\Program Files (x86)\NVIDIA Corporation\PhysX\Common;C:\Program Files (x86)\AMD APP\bin\x86_64;C:\Program Files (x86)\AMD APP\bin\x86;C:\Program Files\Common Files\Microsoft Shared\Windows Live;C:\Program Files (x86)\Common Files\Microsoft Shared\Windows Live;C:\Windows\system32;C:\Windows;C:\Windows\System32\Wbem;C:\Windows\System32\WindowsPowerShell\v1.0\;C:\Program Files (x86)\GTK2-Runtime\bin;C:\Program Files\WIDCOMM\Bluetooth Software\;C:\Program Files\WIDCOMM\Bluetooth Software\syswow64;C:\Program Files (x86)\ATI Technologies\ATI.ACE\Core-Static;C:\Program Files (x86)\Microsoft ASP.NET\ASP.NET Web Pages\v1.0\;C:\Program Files\Microsoft SQL Server\110\Tools\Binn\;C:\Program Files (x86)\QuickTime\QTSystem\;C:\Program Files (x86)\Common Files\Acronis\SnapAPI\;C:\Program Files (x86)\Java\jre7\bin;C:\Program Files (x86)\Windows Kits\8.1\Windows Performance Toolkit\;C:\Program Files (x86)\Microsoft SDKs\TypeScript\;C:\Program Files (x86)\MySQL\MySQL Utilities 1.3.4\; ;C:\Chocolatey\bin;C:\tools\mysql\current\bin I'm being forced to use Windows by my work environment, I don't enjoy the state of affairs.

  Read the article

• How harmful is a hard disk spin cycle?

  - by Gilles

  It is conventional wisdom¹ that each time you spin a hard disk down and back up, you shave some time off its life expectancy. The topic has been discussed before: Is turning off hard disks harmful? What's the effect of standby (spindown) mode on modern hard drives? Common explanations for why spindowns and spinups are harmful are that they induce more stress on the mechanical parts than ordinary running, and that they cause heat variations that are harmful to the device mechanics. Is there any data showing quantitatively how bad a spin cycle is? That is, how much life expectancy does a spin cycle cost? Or, more practically, if I know that I'm not going to need a disk for X seconds, how large should X be to warrant spinning down? ¹ But conventional wisdom has been wrong before; for example, it is commonly held that hard disks should be kept as cool as possible, but the one published study on the topic shows that cooler drives actually fail more. This study is no help here since all the disks surveyed were powered on 24/7.

  Read the article

• IE 8 crashes when opening an html file from an autorun CD

  - by dave4351

  On Windows 7, when I insert a CD with a very simple HTML page referenced in the autorun.inf file, Internet Explorer 8 opens and then immediately crashes, with the error message "Internet Explorer has stopped working" and then checks for a solution. Then it says "A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available." On Windows Vista, IE 8 just opens and then closes silently, with no error messages or help of any kind. I have since discovered this is due to IE 8's "protected mode" and turning this off fixes the issue so that the HTML file on the CD launches normally. What I'd like to know: is there any way to get around this, so that I can launch a simple HTML file in the user's default browser, using an autorun.inf file on a CD, without first having my users open IE 8 and turn off protected mode? Perhaps the most bizarre thing is that if IE is already open when you insert the CD, the HTML page just opens--no crash. It only crashes if IE 8 happens to be closed when you insert the CD. And so a possible workaround may be to get the default browser to launch and then open the HTML file. All suggestions welcome.

  Read the article

• How do you handle data archiving?

  - by 20th Century Boy

  Backups are one thing, but long term archival is another. For example, you might be required to store emails for 7 years, or keep all project data indefinitely. I used to save archives to tape, but then I've had tapes get destroyed (drives rip the tape out). So...write to 2 tapes I hear you say. Is that what others do? Have 2 (or more) tapes of the same data for redundancy? But then the other issue is that tapes cannot usually be read by different backup software vendors. Eg if you go from Arcserve - Backup Exec - Commvault over 10 years you would need to keep all 3 systems so that you could restore old data. Likewise for hardware. Old tapes might not be barcoded. Might not be compatible with the new library etc etc. So do you keep old tape hardware AND old software just in case you might need to restore a 10 year-old file? Or...when you move to a new backup system do you migrate all archived data to the new system and re-archive it onto new tapes? That could be a huge job. Any thoughts?

  Read the article

• Comparing Nginx+PHP-FPM to Apache-mod_php

  - by Rushi

  I'm running Drupal and trying to figure out the best stack to serve it. Apache + mod_php or Nginx + PHP-FPM I used ApacheBench (ab) and Siege to test both setups and I'm seeing Apache performing better. This surprises me a little bit since I've heard a lot of good things about Nginx + PHP-FPM. My current Nginx setup is something that is a bit out of the box, and the same goes for PHP-FPM What optimizations I can make to speed up the Nginx + PHP-FPM combo over Apache and mo_php ? In my tests using ab, Apache is outperforming Nginx significantly (higher requets/second and finishing tests much faster) I've googled around a bit, but since I've never using Nginx, PHP-FPM or FastCGI, I don't exactly know where to start PHP v5.2.13, Drupal v6, latest PHP-FPM and Nginx compiled from source. Apache v2.0.63 ApacheBench Nginx + PHP-FPM Server Software: nginx/0.7.67 Server Hostname: test2.com Server Port: 80 Concurrency Level: 25 ---> Time taken for tests: 158.510008 seconds Complete requests: 1000 Failed requests: 0 Write errors: 0 ---> Requests per second: 6.31 [#/sec] (mean) Time per request: 3962.750 [ms] (mean) Time per request: 158.510 [ms] (mean, across all concurrent requests) Transfer rate: 181.38 [Kbytes/sec] received ApacheBench Apache using mod_php Server Software: Apache/2.0.63 Server Hostname: test1.com Server Port: 80 Concurrency Level: 25 --> Time taken for tests: 63.556663 seconds Complete requests: 1000 Failed requests: 0 Write errors: 0 --> Requests per second: 15.73 [#/sec] (mean) Time per request: 1588.917 [ms] (mean) Time per request: 63.557 [ms] (mean, across all concurrent requests) Transfer rate: 103.94 [Kbytes/sec] received

  Read the article

• Kubuntu: apt-get install of php5-dev: libtool version mismatch?

  - by pinkgothic

  (Warning, clueless-newbism ahead.) Background info: I'm actually trying to install/upgrade xdebug. sudo pecl install xdebug yields: downloading xdebug-2.0.5.tgz ... Starting to download xdebug-2.0.5.tgz (289,234 bytes) ............................................................done: 289,234 bytes 67 source files, building running: phpize sh: phpize: not found ERROR: `phpize' failed A quick google tells me that phpize is a part of a package called php5-dev, so off I ran to install that. My problem is that using sudo apt-get install php5-dev fails with this output: sudo apt-get install php5-dev Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: php5-dev: Conflicts: libtool (>= 2.2) but 2.2.6a-4 is to be installed E: Broken packages 2.2.6a-4 is greater than 2.2, so I'm not sure why it's hanging itself up at that point. I'm guessing the fact that it's not entirely numeric is throwing apt-get off? I can probably install xdebug manually (though I've never done this before, so picture me with a deer clueless-newb in headlights look here, violently shaking my head and begging for a simpler solution) rather than via pecl / aptitude, but is there a way I can make aptitude install php5-dev despite the bogus 'broken package' claim? Is it even bogus, or am I misreading the error message? Alternatively: Could I install phpize in some other way (e.g. via pear or pecl)?

  Read the article

• Kubuntu: apt-get install of php5-dev: libtool version mismatch?

  - by pinkgothic

  (Warning, clueless-newbism ahead.) Background info: I'm actually trying to install/upgrade xdebug. sudo pecl install xdebug yields: downloading xdebug-2.0.5.tgz ... Starting to download xdebug-2.0.5.tgz (289,234 bytes) ............................................................done: 289,234 bytes 67 source files, building running: phpize sh: phpize: not found ERROR: `phpize' failed A quick google tells me that phpize is a part of a package called php5-dev, so off I ran to install that. My problem is that using sudo apt-get install php5-dev fails with this output: sudo apt-get install php5-dev Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: php5-dev: Conflicts: libtool (>= 2.2) but 2.2.6a-4 is to be installed E: Broken packages 2.2.6a-4 is greater than 2.2, so I'm not sure why it's hanging itself up at that point. I'm guessing the fact that it's not entirely numeric is throwing apt-get off? I can probably install xdebug manually (though I've never done this before, so picture me with a deer clueless-newb in headlights look here, violently shaking my head and begging for a simpler solution) rather than via pecl / aptitude, but is there a way I can make aptitude install php5-dev despite the bogus 'broken package' claim? Is it even bogus, or am I misreading the error message? Alternatively: Could I install phpize in some other way (e.g. via pear or pecl)?

  Read the article

• How do I properly configure a ZipInstaller .zic file?

  - by Iszi Rory or Isznti

  As of version 1.20, ZipInstaller is supposed to support the use of a configuration file to customize its installation options. Generally, all the options I want to use are available through the dialog so I really haven't bothered with the configuration file until now. The problem now is that certain tools, such as PsTools from Sysinternals, do not properly show their Product Name to ZipInstaller. ZipInstaller's dialog will let you customize the Start Menu folder and Program Files folder, but that still doesn't change the Product Name that it sees for the software. So, instead of having "PsTools" in my Add/Remove Programs, I get "Sysinternals Software". For some things, the situation is even more confusing. For example, the NIST SP 800-53 Reference Database Application gets installed as "FileMaker Pro Runtime". To rectify this, I've tried to use the aforementioned .zic configuration file. As I understand it, it's a basic INI file you create and put in the root of the ZIP file. ZipInstaller is supposed to read that file, and adjust its parameters accordingly. Mine looks like this: [install] ProductName=NIST_SP_800-53 ProductVersion=1.4.1 CompanyName=NIST Description=NIST_SP_800-53 InstallFolder=%zi.ProgramFiles%\%zi.ProductName% StartMenuFolder=%zi.CompanyName%\%zi.ProductName% I've named it `~zipinst~.zic and placed it in the root of the ZIP file, but when I run ZipInstaller it doesn't seem to recognize any of the information I've given it in the .zic file. What might I be doing wrong here?

  Read the article

• Use one NIC to create multiple interfaces for Linux KVM

  - by Phanto

  I am working on a thesis research project, and I am having some difficulty figuring out how to make one NIC spawn several "bridge" interfaces such that each KVM VM can be seen on the local network. I am very new to KVM, and am still exploring what it can do. Below is the scenario that I am attempting to make (on a CentOS/RHEL 6 system): Linux KVM Host has 1 NIC (eth0) connected to a switch. Create multiple "bridge" or equivalent interfaces that are spawned off of eth0 that would provide a unique IP for each VM. This is so that each VM can communicate with other hosts on the network, and that other hosts on the network can communicate with the VM. IMPORTANT: I would like iptables on the KVM host to be able to manipulate/control/restrict the traffic that would be sent on those "bridge" interfaces. I would like to create a minimum of three VM's, each using their own unique "bridge" interfaces. I have previously made a br0 interface off of eth0, but unfortunately, I am unable to add any more to it. It appears that you can only bridge 1 interface to the NIC. I would like to bridge many to one. Would a tap device be able to do this? If so, how would it be set up? Effectively, I am attempting to replicate what can easily be created with VirtualBox on Windows, where each VM is given a "bridged" interface, and can live on the network. I want to achieve this very same thing with Linux KVM. Thank You EDIT: To be more descriptive, I want to achieve something that looks like this: This can be found on this page: http://en.gentoo-wiki.com/wiki/KVM#Networking_2 HOST +---------------+ | | KVM GUEST1 | | +--------------+ | +------+ | | | LAN ---+--- eth0 | +--+---+---- nic0 | KVM GUEST2 | | tap0----+ | |192.168.1.13 | +--------------+ | | tap1----+ | +--------------+ | | | +------+ | | | | | br0 +--+----------------------+---- nic0 | |192.168.1.12 | |192.168.1.14 | +---------------+ +--------------+

  Read the article

• Juniper NetScreen NS-5GT traffic monitoring

  - by blah

  I've done casual research into the subject and am truly dismayed at the lack of compatible tools for such a simple task. Maybe someone can provide assistance. We have a NetScreen NS-5GT in the office. I need to be able to get a glance of current traffic per endpoint -- I think the equivalent of 'get sessions' with byte counts/rates. I don't care about bars, graphs, and reports. Something as simple as a classic software firewall display would be perfect. I can't shell out money on something real like SolarWinds products, so a free solution is essential. I'm willing to do a little work but refuse to program something from scratch. It's not prudent right now for me to install a hub or otherwise mess around physically. There must be something out there I can use, maybe in combination. I don't believe I'm asking too much. Specific answers only please, e.g. monitoring software you know will actually work with this antiquated device. I've read about general approaches to the broader problem dozens of times already.

  Read the article

• Cisco 7206 error trying to copy running-config (Bad file number)

  - by jasondewitt

  I have a cisco 7206 that terminates a bunch of pppoa sessions for dsl users. Today I noticed that if I tried to "show run" nothing happened. I mean that it doesn't show anything and just sends me right back to the command prompt. I decided I should probably try and back up the config and that is where I'm stuck. Any time I try to copy the running-config to tftp or to pcmcia card that I know is not full I get the following error: %Error opening system:/running-config (Bad file number) I get this error when I try to do anything with the running config. I've been googling around, but I haven't found any thing else that talks about this error. I've seen people say to erase the nvram and then try to "copy run start", but I don't want to erase the nvram until I can pull off a copy of the running-config. I would try to reboot it, but the startup-config that is on the nvram looks to be woefully out of date (good job me!). Any ideas what might be wrong? or how I can get the running config off the router?

  Read the article

• can't properly shutdown ubuntu and sound problem on HP mini 311 netbook

  - by Viele

  hi, I recently bought a HP mini 311 netbook. I replaced its harddrive and installed ubuntu 10.04. Since then, I have encountered some very strange problem with its sound and shutdown/reboot. At times, when I start the computer, it will have no sound, on the GUI the sound is at max, but no sound is available. This sometimes also happen after after upgrades, hibernate, and toggling the wireless radio button. Strangely, when the sound is out the device will also refuse to be shutdown. If I shutdown the computer using the GUI, it will simply go back to the log in screen without actually shutting down. If I use "sudo shutdown 0", the computer will hang on the loading screen of the shut down process. I had to force the pc to shutdown by holding the power button down. usually (probably always) after I force a turn-off then start off again. the sound and shutdown become normal. I wonder if anyone have clues regarding to the cause of this problem. This the info about the computer: 1) installed ubuntu 10.04LTS RC, later upgraded to formal released version. 2) cat /proc/asound/version == "Advanced Linux Sound Architecture Driver Version 1.0.21." however, when doing 'alsaconf' the version displayed is 1.0.23 any help is appreciated. Thanks

  Read the article

• I am looking for a tool to measure or detect "unresponsiveness" of a desktop PC

  - by Tom H

  I have a client that provides some server systems to a hospital, and a support ticket was raised that the desktop application was hanging waiting for the server. We did some extensive testing and its pretty clear that the server is responsive, and the network is fine, and that the problem is on the client end. (no requests are received during the hang etc...) We take a look at the desktop machines and they should be fine, so we raise tickets with the software vendor who says that it must be the hardware, the hardware company says that it is the software, etc etc Anyway, so talking to the nurses, they say that these machines often "hang" for 30 seconds at a time, and sometimes during important moments where they need to get data for a patient who is unwell, such as charts and status. So I want to stick a client on these machines that would be able to detect arbitrary "unresponsiveness" of the keyboard/mouse and log that for analysis later. Obviously I am wary to suggest some application that takes resources and makes the problem even worse, so I would interested to see any tools that would detect these (is it correct to say that the keyboard interrupts are being discarded?) scenarios by looking for the OS discarding the interrupts, or whatever is appropriate here. so go on then serverfault, here is your chance to save a life.... ;-) Edit: I am starting to think that some of the tools associated with real time systems might be appropriate, at least as a diagnostic.

  Read the article

• Seeking web-based FTP client for very large file upload

  - by Paul M. Nguyen

  I have looked around for these for some time... the limits imposed by the web server and/or the dynamic programming environment (e.g. PHP) are far too restrictive for the application I'm working on. We need to be able to move large graphics and video files to and from clients (ranging from tens of MB to a few GB in a single file). Plain FTP with a proper desktop client will do the trick, and we're hosting this in Amazon EC2 with EBS. User management will be done from the office via webmin. Users are chroot-jailed into their home dir by proftpd. net2ftp will work for many clients, but we often need to move single files that approach 1GB or exceed 2-3GB which is way out of the range of any http-based uploader. So we turn to Java or Flash - can they do it? From within the web browser establish an FTP connection and grab a huge file? There are licensed applets and such out there, but none seem convincing. Again, I'm looking for some code that can speak FTP and read (& write?) the local disk, that is delivered in a web browser, and can move single files of 2GB+. The reason for having a web-based interface to FTP is to skip the software installation step for our clients. I will consider proper desktop client software as long as it's "portable" and at least Win+Mac and can be easily configured by lay-man users in a hurry.

  Read the article

• How can adding a server to a domain cause Remote Desktop to stop working?

  - by Adrian Grigore

  I have two dedicated with Windows 2008 R2 servers which I am using for Web hosting. One Server A is a domain controller, Server B should simply be added to the domain controlled by Server A. So I RDP'd into Server B and changed the system settings so that Server B is part of that domain. I entered my domain admin credentials, was welcomed to the domain and asked to reboot the server. So far everything seemed to work smoothly After rebooting, I could not open an RDP connection to Server B anymore: Remote Desktop can’t connect to the remote computer for one of these reasons: 1) Remote access to the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network Make sure the remote computer is turned on and connected to the network, and that remote access is enabled. I restored an older backup of Server B and switched off the firewall before adding the server to my domain. But the problem reoccurred just the same. What could be the reason for this? The domain is brandnew and I did not change any of the default settings. Could this be some kind of domain-wide default policy that shuts down RDP on any domain clients? Or perhaps it has to do with the fact that Server B is virtual? Thanks for your help, Adrian

  Read the article

• Domain joined computer unable to access servers through VPN

  - by kscott

  Our servers are in a virtual off site hosting center, our office has a vpn connection to the data center, but for reasons I don't understand we also have to connect to the Citrix Access Gateway (CAG) client in order to access the servers. I am a programmer with rather limited ops knowledge including a weak grasp of networking and terminology. Bear with me. I was just given a new laptop, which is a 64 bit Windows 7 system unlike my previous 32 bit Windows XP desktop which was able to connect without issue. My laptop has been joined to the domain so that I login with my AD credentials, I am able to connect to the CAG and get authenticated, and after doing this I can ping our servers and they resolve to the correct internal IP addresses, but I am unable to use remote desktop to the servers, connect to SQL servers through my local SQL Management Studio, navigate to them through the file system, or view any of our internal intranet websites. All of which I was able to do previously. I have tried turning off my Windows firewall and the problem remains, the DNS servers are set to the correct IPs of our domain controllers, and the ops guys here are a little stumped. Does any one have any suggestions?

  Read the article

• Easy GUI way to auto scale EC2 and RDS: aws console, scalr, ylastic...?

  - by Zillo

  I am managing all my instances with the AWS Management Console (the GUI web console) but now I want to use Auto Scale and it seems that this can not be done with that console. Yes, there is CloudWatch but I can only create alarms (e-mail notifications), it seems that CouldWatch needs you to add the auto scale policy in some other place (by command line console?). I would like to use some easy GUI interface. Ylastic and Scalr seems to be a good option. Which one do you think is better? Regarding Scalr, is there any difference between the open source software Scalr and the service Scalr.net? I mean, is the GUI interface the same? I like the idea of the Scalr because I do not need to give my Secret Access Key to a third party (like in Ylastic or in Scalr.net) One question about the Scalr software, it has to be installed in the instances or it must be installed in another machine? Do I need to setup again all my security permissions, AMIs, snapshots, etc. or I can use AWS Management Console for everything and Scalr just to auto scale.

  Read the article

• Nginx Slower than Apache??

  - by ichilton

  Hi, I've just setup 2x identical Rackspace Cloud instances and am doing some comparisons and benchmarks to compare Apache and Nginx. I'm testing with a 3.4k png file and initially 512MB server instances but have now moved to 1024MB server instances. I'm very surprised to see that whatever I try, Apache seems to consistently outperform Nginx....what am I doing wrong? Nginx: Server Software: nginx/0.8.54 Server Port: 80 Document Length: 3400 bytes Concurrency Level: 100 Time taken for tests: 2.320 seconds Complete requests: 1000 Failed requests: 0 Write errors: 0 Total transferred: 3612000 bytes HTML transferred: 3400000 bytes Requests per second: 431.01 [#/sec] (mean) Time per request: 232.014 [ms] (mean) Time per request: 2.320 [ms] (mean, across all concurrent requests) Transfer rate: 1520.31 [Kbytes/sec] received Connection Times (ms) min mean[+/-sd] median max Connect: 0 11 15.7 3 120 Processing: 1 35 76.9 20 1674 Waiting: 1 31 73.0 19 1674 Total: 1 46 79.1 21 1693 Percentage of the requests served within a certain time (ms) 50% 21 66% 39 75% 40 80% 40 90% 98 95% 136 98% 269 99% 334 100% 1693 (longest request) And Apache: Server Software: Apache/2.2.16 Server Port: 80 Document Length: 3400 bytes Concurrency Level: 100 Time taken for tests: 1.346 seconds Complete requests: 1000 Failed requests: 0 Write errors: 0 Total transferred: 3647000 bytes HTML transferred: 3400000 bytes Requests per second: 742.90 [#/sec] (mean) Time per request: 134.608 [ms] (mean) Time per request: 1.346 [ms] (mean, across all concurrent requests) Transfer rate: 2645.85 [Kbytes/sec] received Connection Times (ms) min mean[+/-sd] median max Connect: 0 1 3.7 0 27 Processing: 0 3 6.2 1 29 Waiting: 0 2 5.0 1 29 Total: 1 4 7.0 1 29 Percentage of the requests served within a certain time (ms) 50% 1 66% 1 75% 1 80% 1 90% 17 95% 19 98% 26 99% 27 100% 29 (longest request) I'm currently using worker_processes 4; and worker_connections 1024; but i've tried and benchmarked different values and see the same behaviour on all - I just can't get it to perform as well as Apache and from what i've read previously, i'm shocked about this! Can anyone give any advice? Thanks, Ian

  Read the article

• Copy a harddrive from a failed desktop machine using a second working one. [closed]

  - by MrEyes

  Heres the scenario: I have PC-A, an old PC that runs Windows XP but now refuses to boot due to a failed motherboard (or maybe PSU). This PC has a single 80gb IDE drive. I also have PC-B, running Windows Vista, this is working fine. I want to copy all the data off PC-As HDD onto PC-B. To do this I have taken the HDD out of PC-A and connected it as a slave to PC-B. PC-B now boots and sees the additional drive. However, when I attempt to access/copy user folders (i.e. Documents and Settings/[username]/*) I am told that I cannot access the folders due to user permissions. I am doing this under an adminstrator account on PC-B. So the question is, how can I "backup" the data? Preferably without making any changes to the drive contents. The reason for this is that it is possible that PC-A is failing due to a bad PSU, so I intend to replace it before writing off the machine. However I would feel much happier if I had a backup of the data on the HDD.

  Read the article

< Previous Page | 479 480 481 482 483 484 485 486 487 488 489 490  | Next Page >