Search Results

Search found 7502 results on 301 pages for 'defective hardware'.

Page 49/301 | < Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >

  • Building a Media Center PC with Comcast Cable...?

    - by Rob
    Alright - so this might be a stupid question but I've never been all that much into TV. I currently have Comcast cable. I've just got the 'basic' 2-60 package or whatever; I've just always plugged the cable into the back of my TV. I've never had a cable box. Recently, Comcast has been pulling channels off of my line-up. Most recently, the stole the TV Guide channel from me. I'm told this is part of a push to get customers to switch to their digital line-up. But, I'm also told it requires some sort of digital receiver for each TV you've got. I don't want to buy a bunch of these digital receivers and I don't want to pay the monthly rental fee...but I have heard of how awesome media center PCs are and some really cool things they can do. And, I've got loads of PC parts sitting around. So, can someone guide me through this a bit? Are there computer video cards or TV tuners that are going to work with Comcast's digital cable? What kind of price range are we looking at?

    Read the article

  • DVD-ROM disappeared under Windows-7

    - by hometoast
    Windows-7 (build 7100) has forgotten about and refused to recognize that I have an optical drive attached. Linux LiveCD sees it (sees it and it boots from it), so it's isolated to the Windows installation. I do have VirtualCloneDrive installed. But I know I had access to the optical drive after the installation of that. Only recently did I try to rip an iso image for mounting in a VM. I do not see the device under device manager (Start,Run,"devmgmt.msc"). I really do not want to do a fresh install. What are my next steps?

    Read the article

  • What will happen with my RAID5 after motherboard change?

    - by abatishchev
    Currently I have ASUS P5Q-EM and 3 HDD in RAID5 using it's on-board RAID controller Intel ICH10R. I want to bye a new motherboard, for example, Gigabyte GA-EQ45M-S2 which also have on-board RAID controller, but Intel ICH10DO. What will happen with my data on RAID5? Will I have to re-create the array from the scratch and lost all my data? Is such array a soft RAID or soft-hard? What if my current motherboard will broken? What will happen with my data?

    Read the article

  • 4 GB DDR2 vs 2 GB DDR 3...........

    - by metal gear solid
    I 'm going to purchase new PC. due to my budget limit either i can purchase 2 x 2GB = 4GB DDR 2 or 2 GB Single stick DDR 3. Will 2 GB DDR 3 will give almost same performane compare to 4 GB DDR 2? In future I will upgrade RAM upto 8 GB Which option would be better for me for now and why?

    Read the article

  • Compaq Presario CQ40 unexpected turn off

    - by CRoshanLG
    My Compaq Presario CQ40 (yeah, its pretty old) suddenly turns off after about 1/2 - 1 hour usage without any notice or warning. The power cable and adapter works fine (indicator bulbs show that power is given to the laptop), but it seems like machine suddenly plugged off from the power source. And when I try to switch it on, after the sudden turn off it simply won't turn on. I can only turn it on after letting it to rest for at least couple of hours! ** The battery has been dead for some time now, but it has been working fine on direct power supply until recently. Has anyone encountered this? and hopefully knows any cure?

    Read the article

  • Can two users both control a third machine simultaneously using Synergy?

    - by Reason
    I've been a Synergy user for some time now, as I use a PC on the left side of my Mac. My girlfriend and I both have our desks on each side of the other, and we'd like to know if it were possible for the both of us to control the PC in the middle, with our own separate mouse & keyboards. Here's a crude drawing of our setup (1) her pc (2) my pc (3) my mac Currently, 3 is running a synergy server, and 2 is running the client. But like I said, I'm wondering if there's a way for 1 & 3 to both control 2 with their own mouse and keyboard. I'd ~love~ to have it set up where we could go even farther, and have both of our mice & keyboards able to control all 3 computers at the same time, for moments when we need to click or press keys for each other. But that seems a little too much to ask! Any thoughts?

    Read the article

  • Ubuntu: On-screen keyboard

    - by Paul Lammertsma
    On a similar note to this question, I recently booted Ubuntu to recover a Windows partition, but couldn't in any way get the keyboard to register. I recall back in 8.x that you could easily reach the on-screen keyboard (Virtual Keyboard?) via "Assistive Technologies". It seems to have disappeared since 9.x. For future reference, how can I easily get to it? Recall that in this scenario I won't have a keyboard to enter terminal commands (e.g. to install xkbd or something of the like).

    Read the article

  • (Arch)Linux board with dual ethernet

    - by tekknolagi
    I am looking for a Linux board with the following requirements: 2 ethernet ports (helpful, but only 1 required) 2 USB ports SDXC support (for SD/MicroSD) WiFi (25 concurrent users ideally) HDMI or micro HDMI out I don't know of a good way to find boards. I went through and catalogued a bunch in a spreadsheet, though: https://docs.google.com/spreadsheets/d/1ZyWvg1u5jAeCq4ghpQv3fukl78nYO64utfQgzTP1r7w/edit?usp=sharing

    Read the article

  • System Event ID 11 Disk

    - by Guy Thomas
    Upon starting Windows Server 2008 R2 I get this error message: Event ID 11 Disk The driver detected a controller error on \Device\Harddisk3\DR3. There are also also 3 more similar messages for Harddisk 2, 4, and 5, but not zero or 1. Checking the event viewer reveals it's been going on for 3 months. I ran chkdsk - no bad sectors. Any advice on the cause, better still, a solution?

    Read the article

  • Why does a hard disk suddenly look to Windows as if it "needs to be formatted"?

    - by pufferfish
    This is more of a theory question, but what are the reason(s) for a disk to suddenly cause Windows to start saying it "needs to be formatted"? It happens to an IDE disk that I have in a cheap external enclosure, and I can usually get most of the data back by using software like recuva. It's now happened to an internal disk I have. I'm not looking for software to fix this (although links would be appreciated), but rather a low-level explanation as to what gets corrupted on the disk.

    Read the article

  • Server 2008 Hard Faults

    - by claw
    Hey all, plase bear with me as I haven't looked at a server in a very long time. The problem I am having is with a Windows 2008 Standard FE Service Pack 2 Intel Xeon X3430 @ 2.40 2.39 GHZ 4 GB Memory 64 Bit There seems to be no problems other than the physical memory peaking at 91%, always with over 100 Hard Faults Per Second. To my understanding hard faults should be fairly rare on a machine with. Are there any logs I can show you? Or investigate myself. The general performance of the machine is ok, i can access SBS2008 and change settings fairly smoothly without hangs etc. However, we connect to the server and do quite a bit of SQL via an application. For a record to retrieve say 20 rows, it can take 20+ seconds. Thanks in advance, Jamie EDIT: What the server is used for: IIS ASP Web Service SQL 2008 List item Exchange unable to upload screenshots due to low reputation - why doesnt my SO work here :)

    Read the article

  • XP Restart After Power Failure

    - by Jim
    Hello, I've almost got my power settings sorted and was hoping someone could help? If I'm running XP and the power is cut, when the power is restored my machine auto restarts (this is what I want!) However, if I shutdown my machine properly (from the start menu & without touching the PC power button!), then switch the power off at the socket, then switch the power back on, the PC does not automatically restart. It's like the bios(?) recieives a message saying "aha, genuine shutdown and not a power cut, therefore do not restart on power restore." I want my PC to restart everytime it sees power restored from the socket? Any way round this? Anyone seen this before? I've upgraded my bios. Thanks in advance, Jim

    Read the article

  • Why DELL PowerConnect and Juniper are so rare ? Why do enterprises stick with Cisco ?

    - by Kedare
    Hello ! I have a little question, I'm actually studing IT in France, and when looking on alternative on the very [...] very expensive Cisco equipments, I've found Juniper and DELL PowerConnect pretty attractive on features and price, but I rarely see something else than the classics Cisco/LinkSys, HP Procurve and Netgear.. Why it's so rare to find those switch ? They looks really great but... I've never seen any Juniper or Powerconnect... Why do enterprises stick with the expensive Cisco ? I've tried to find how to buy both, it's quite easy with PowerConnect, everything is on the DELL website, but it looks it's very hard to find Juniper equipments in France :( Thank you !

    Read the article

  • Windows detected a hard disk failure* - what should I do?

    - by bart
    I'm using Windows 7 x64 Ultimate, I'm getting windows error popups like this one for about 3 days, multiple times a day: This Samsung SpinPoint F3 HD502HJ 500 GB is about 2 years old and I already checked it with Samsung ES Tool 3.0, did all the scans (took hours) and everything is fine! I have no malware, viruses and this started to happen after I have had some electrcity issues at my house (multiple power surges / overvolatege during the night, PC was connected, but turned off), any ideas? What other test should I perform? I believe the disk could be damaged, but then diagnostic tools should prove this, right? *in fact "Windows detected hard disk problem" but I was unable to put word "problem" within the title as well.

    Read the article

  • What would make a noise in a PC on graphics operations on a passively-cooled system?

    - by T.J. Crowder
    I have this system based on the Intel D510MO motherboard, which is basically an Atom D510 (dual-core HT Atom w/built-in GPU), an Intel NM10 chipset, and a Realtek Gigabit LAN controller. It's entirely passively cooled. I noticed almost immediately that there was a kind of very, very soft noise that corresponded with graphics operations, sort of the noise you'd get if you had a sheet of flat paper and slid something really light across it — but more electronic than that. I wrote it off as observation error and/or disk activity triggered by the graphics operation (although the latter seemed like a lot of unnecessary disk activity). It isn't. I got curious enough that I finally did a few controlled experiments, and here's what I've determined: It isn't the HDD. For one thing, the sounds the HDD makes (when seeking, when reading or writing, when just sitting there spinning) is different. For another, I used sudo hdparm -y /dev/sda (I'm using Ubuntu 10.04 LTS) to temporarily put the disk on standby while making sure that non-disk graphics op was happening in a loop. The disk spun down, but the other sound continued, corresponding perfectly with the timing of the graphics op. (Then the disk spun up again, but it takes long enough that I could rule out the HDD.) It isn't the monitor; I ensured the two were well physically-separated and the sound was definitely coming from the main box. It isn't something else in the room; the sound is coming from the box. It isn't cross-talk to an audio circuit coming out the speakers. (It doesn't have any speakers.) It isn't my mouse (e.g., when I'm trying to make graphics ops happen); the sound happens if I set up a recurring operation and don't use the mouse at all, or if I lift the mouse off the table slightly (but enough that the laser still registers movement). It isn't the voices in my head; they never whisper like that. Other observations: It doesn't seem to matter what the graphics operation is; anything that changes what's on the screen seems to do it. I get the sound when moving the mouse over the Chromium tab bar (which makes the tab backgrounds change); I get it when a web page has a counter on it that changes the text on the page: I get it when dragging window contents around. The sound is very, very slightly louder if the graphics op is larger, like scrolling a text area when writing a question on superuser.com, than for smaller operations like the tick counter on the web page. But it's very slight. It's fairly loud (and of good duration) when the op involves color changes to substantial surface areas. For instance, when asking a question here on superuser and you move the cursor between the question box and the tag box, and the help to the right fades out, changes, and fades back in. (Yet another example related to the web browser, so let me say: I hear it when operations completely unrelated to the web browser as well.) It doesn't sound like arcing or anything like that (I'd've shut off the machine Right Quick Like if it did). Moving windows does it. Scrolling windows (by and large) doesn't. I have the feeling I've heard this sort of thing before, when all system fans were on low and such, with other systems — but (again) written it off as observational error. For all the world it's like I'm hearing the CPU working (as opposed to the GPU; note the window scroll thing above) or data being transferred somewhere, but that just seems...unlikely. So what am I hearing? This may seem like a very localized question, but perhaps other silent PC enthusiasts may be interested as well...

    Read the article

  • Warning for "Reallocated Event Count" S.M.A.R.T. attribute with a new/unused drive. How serious is t

    - by Developer Art
    I've just looked at the health status of my old 2,5 inch 500 Gb Fujitsu drive with a popular "HD Tune" utility. It shows a warning for the "Reallocated Event Count" property. How serious is that? The thing is that the drive is practically new. I pulled it out of a new laptop over a year ago and never used it since. Right now it only has 53 "Power On" hours which sounds about right since I only had it running a few evenings overnight before switching it for something more performant. Does this warning indicate that the drive is likely to fail some time in the future? I'm somewhat perplexed since the drive is effectively unused. What is more, I have arranged with somebody to buy off this drive since I don't really need. It is 12,5 mm thick (with 3 plates) meaning it doesn't fit into an external enclosure which makes it quite useless to me. Can I give away the drive without having it on my conscience or better cancel the deal? In other words, can the drive be used safely for years to come or better throw it away? I'm running a sector test now to see if there are any real problems. Will post the results as soon as they're available.

    Read the article

  • Router recommendation to virtualize 800 IPs

    - by delerious010
    I've recently been looking at getting some new load balancers for our environment as we are expecting to double our client base in the next 12 months. Currently we have 400 public IPS serving 800 clusters ( 2 clusters / IP due to ports ) on Coyote Point Balancers, and distributing connections to 3 web servers serving about 6GBytes outgoing, 2Gbytes in per day. If we double, this would be about 800 IPs, possibly 1600 clusters, and about 6 servers per cluster ( for a total of 9600 so called "real servers" using Barracuda's lingo ). Due to the amount of clusters, most solutions I've looked at ( Coyote, Barracuda, Loadbalancer.org ) seem to be unsure whether they'll be able to handle our planned growth, mostly due to health checks performed on the servers ... which makes total sense when you think of it. So the fine folk at loadbalancer.org recommended that we may be better off offload the 400-800 public IPs, which we require for SSL eCommerce solutions, over to a forward facing router. From that point on, the router could do some mangling to route EXT_IP:443 to INT_IP:INT_PORT which would then allow us to reduce the Load Balancer configuration to 1 or 2 clusters, thus resolving the health check problem. Does this idea make sense to yall ? Or would you have other recommendations to make ? Secondly, what router would you recommend for such an undertaking ? I'd be looking at something that has some form of failover mechanism built in. On a totally unrelated note, I've got to admit that I'm extremely pleased with the responses I got from loadbalancer.org. Their responses to my inquiries were surprisingly helpful ( i.e. I didn't feel as if I was taking to a sales guy trying to push something ). ( No I don't work for them, and sadly nor are they sending me free gear ).

    Read the article

  • Mouse for a lefty?

    - by Kyralessa
    As a programmer, I'm fairly particular about my keyboard and mouse. One thing I've only recently noticed is that the mice I tend to prefer don't work well for my five-year-old. He's left-handed, but ends up mousing with his right hand on the computer because (a) that's where the mouse is, and (b) most mice are designed for right-handed people anyway. So, a couple of questions: If you're left-handed and you mouse with your left hand, do you have any recommendations on good mice? If you have a lefty in your household (whether or not it's you), is there an easy way to swap settings between left-handed and right-handed mouse buttons? One way is Control Panel Mouse Check the box on the first tab OK. Do you know of anything faster? Or, better yet, what I'd really like is a way to reverse those settings on only one particular mouse, which would be designated as my son's mouse.

    Read the article

  • Experience with AMCC 3ware 9650se raid cards? Ours seems dead

    - by antiduh
    We have a 8-port 3ware 9650se raid card for our main disk array. We had to bring the server down for a pending power outage, and when we turned the machine back on, the raid card never started. This card has been in service for a couple years without problems, and was working up until the shutdown. Now, when we turn the machine on, the bios option rom that normally kicks in before the bootloader doesn't show up, none of the drives start, and when the OS tries to access the device, it just times out. The firmware on it has been upgraded in the past, so it's possible we've hit some sort of firmware bug. We're using it in a Silicon Mechanics R272 machine with gentoo for the OS. The OS eventually boots, but alas, without the card. We've ordered a new one, but I'm worried that if we replace the card it won't recognize the existing array. Has anybody performed a card swap before? Any help would be greatly appreciated.

    Read the article

  • is my touchpad dying? Gentoo Linux

    - by Walter White
    Hi all, My touchpad on my laptop appears to be no longer functioning. I typically use an external keyboard and mouse so I didn't notice the problem until I tried to use the touchpad. Even after toggling the on/off switch several times, the touchpad still doesn't work. In the logs, I see something about cannot read byte from synaptics device. I will post the full logs when I am in front of my machine. Thanks, Walter

    Read the article

< Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >