Search Results

Search found 1861 results on 75 pages for 'loss'.

Page 49/75 | < Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >

• Linux server: Dropped packets

  - by Lars

  I see dropped packets using ifconfig on my eth0 interface: eth0 Link encap:Ethernet HWaddr 00:15:17:0d:03:ca inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:30268348 errors:0 dropped:70721 overruns:0 frame:0 TX packets:133076885 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8699434077 (8.6 GB) TX bytes:194937313025 (194.9 GB) Interrupt:16 Memory:feae0000-feb00000 When i use ethtool -S i dont see anything wrong: NIC statistics: rx_packets: 30267138 tx_packets: 133074510 rx_bytes: 8699356158 tx_bytes: 194934147340 rx_broadcast: 35296 tx_broadcast: 5435 rx_multicast: 0 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 0 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 5757001 tx_tcp_seg_failed: 0 rx_flow_control_xon: 8649 rx_flow_control_xoff: 62072 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 8699356158 rx_csum_offload_good: 30212111 rx_csum_offload_errors: 0 rx_header_split: 10857552 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 0 rx_dma_failed: 0 tx_dma_failed: 0 I am running Ubuntu 12.04 with kernel 3.2.0-30-generic #48-Ubuntu SMP I have pinged every device on my internal network for about 24 hours, without packet loss. Also checked my router and my interface to the WAN, also no errors there. Does anyone have any clue?

  Read the article

• Windows Network File Transfer to Samba server: “Are you sure you want to copy this file without its properties?”

  - by jimp

  I am transferring a lot of files to a new NAS based on OpenMediaVault, with the Samba 3.5.6 service running. I am transferring from Windows 7 64-bit to the NAS, and on some media files Windows is prompting about losing some property data across the transfer. I have never seen this before when transferring to Samba boxes I have built myself (vs this turnkey solution), so I'm guessing there must be a Samba setting I can change to preserve the file properties in question instead of permanently losing whatever they contain (Date Taken? Exposure? Flash Fired? etc). Or maybe I've just never encountered this before; I'm really not sure. I tried adding ea support = yes and store dos attributes = yes to the [global] section, but the problem remains. The Linux file system is ext4 mounted with user_xattr (full options: defaults,acl,user_xattr,noexec,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0) as Samba requires. Any ideas would be greatly appreciated. Thank you! Samba config: [global] workgroup = WORKGROUP server string = %h server include = /etc/samba/dhcp.conf dns proxy = no log level = 2 syslog = 2 log file = /var/log/samba/log.%m max log size = 1000 syslog only = yes panic action = /usr/share/samba/panic-action %d encrypt passwords = true passdb backend = tdbsam obey pam restrictions = yes unix password sync = no passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . pam password change = yes socket options = TCP_NODELAY IPTOS_LOWDELAY guest account = nobody load printers = no disable spoolss = yes printing = bsd printcap name = /dev/null unix extensions = yes wide links = no create mask = 0777 directory mask = 0777 use sendfile = no null passwords = no local master = yes time server = yes wins support = yes ea support = yes store dos attributes = yes Note: I found this related question, but it explains the loss due to the user trying to transfer from NTFS to FAT32.

  Read the article

• PTR and A record must match?

  - by somecallmemike

  RFC 1912 Section 2.1 states the following: Make sure your PTR and A records match. For every IP address, there should be a matching PTR record in the in-addr.arpa domain. If a host is multi-homed, (more than one IP address) make sure that all IP addresses have a corresponding PTR record (not just the first one). Failure to have matching PTR and A records can cause loss of Internet services similar to not being registered in the DNS at all. Also, PTR records must point back to a valid A record, not a alias defined by a CNAME. It is highly recommended that you use some software which automates this checking, or generate your DNS data from a database which automatically creates consistent data. This does not make any sense to me, should an ISP keep matching A records for every PTR record? It seems to me that it's only important if the IP address that the PTR record describes is hosting a service that is sensitive to DNS being mismatched (such as email hosting). In that case the forward zone would be configured under a domain name (examples follow the format 'zone - record'): domain.tld -> mail IN A 1.2.3.4 And the PTR record would be configured to match: 3.2.1.in-addr.arpa -> 4 IN PTR mail.domain.tld. Would there be any reason for the ISP to host a forward lookup for an IP address on their network like this?: ispdomain.tld -> broadband-ip-1 IN A 1.2.3.4

  Read the article

• Server 2003 R2 - II6- granting access to website via IP with subnet range

  - by John

  We are trying to allow for a client to connect to our website. By default we are Denying all access except for those with the specified IPs we have configured to run, everything before has just been a single IP address. However now we must implement a range of IPs and rather than input thousands of records we want to use the group of computer options in the Grant Access page. However we have it configured to work off of the IP 72.21.192.0 with a subnet mask of 255.255.224.0 They are unable to connect. Looking over our IIS logs they are receiving a 302 error which is the same behavior anyone should get whom is unauthorized to view the page in question. The IP address coming in is 72.21.217.2, so it should be well within the rage of acceptable IP addresses. I'm at a loss as everything I look up tells me to do what we are doing. So any insight would be appreciated. Especially because I'm a software guy not hardware. Thanks!

  Read the article

• Plone site randomly serving wrong content

  - by Chris Miller

  I have a Plone site that has begun to randomly serve up the wrong content. Any given content suddenly shows something else. Sometimes a JPEG loads a stylesheet instead or a stylesheet loads as a page or a page as an image. The images move around, some times our site logo shows a bullet, or one of the other site images. Fiddler shows the wrong content in the response, the apache logs show the content type of the incorrect file (so if the an image loads in place of a style sheet, apache shows that). We thought mod_proxy was the source of our grief, but we get the problem hitting Zope directly. I never get the wrong content using the Medusa Monitor to repeatedly hit the content. I do see ConflictErrors in the instance.log file, and they seem to be correlated to the problem, but not 100%. ZPublisher.Conflict ConflictError at \path\to\object: database conflict error (oid 0x3586, class BTrees._OIBTree.OIBTree, serial this txn started with blah, serial currently committed blah) (X conflicts (0 unresolved) since startup blah) I pulled that off the web, it's not from our logs, but it's the same message. This may be a red herring, it sounds like those messages are normal. We've updated to the 3.3.5, same problems. I'm at a loss. I'm wondering if there a good way to intercept what is being served? Secondly, is there a way to increase the verbosity of the access log to included the content-type? I've even seen the problem manifest in ZMI. It happens more often when we're authenticated. Sometimes it can take a thousand reloads to see the problem, other times it happens in different ways every time we reload. I believe we've seen this problem for a couple years, but it was very intermittent, a page would show the content of a GIF, then a reload later wouldn't happen for a long time. Now it's a huge problem.

  Read the article

• KVM Guest Reboot Loop

  - by javano

  I have been pulled into a situation where a KVM server (CentOS 6.2) lost power and upon reboot one of the guests hasn't started up again (XP SP3). I have SSH'ed in and someone must have changed something relating to the hyper visors prior to the power loss, but not rebooted all the guests. This particular guest wouldn't start because it was configured to use /usr/bin/qemu-system-x86_64 which isn't there now (assuming it was before?). I changed it to use /usr/libexec/qemu-kvm as this is what all the other guests on this server seem to be using, and its booting up. Using virt-manager on my local machine I can connect to the display of the XP machine and it gets as far as this screen; http://support.gateway.com/emachines/issues/2-1131285152-01.gif The problem I face now, is that which ever option I choose the machine just reboots. So it's and endless loop. I thought that perhaps a file system error maybe present due to the unclean shutdown. There is an XP SP3 ISO mounted under the guest, which I booted from in an attempt to access the recovery tools, but I don't have the Administrator password! I am out of ideas, and it's turning out to be quite the conundrum. Should I use a 3rd party live CD to test the FS for errors? How else can I trouble shoot these restarts?

  Read the article

• Intermittent extrememly long response times when downloading documents

  - by pap

  I have a Java web application running om Tomcat 7 with an Apache httpd 2.2 fronting with mod_jk/AJP. One part of the application is serving files (up to 4mb size). Now, normally this all runs very smooth with stable, low response-times. However, in rare instances (<0.1% of downloads), the downloadtime will go beyond 1 minute. After activating the ThreadStuckValve in Tomcat, I can see that the long responses seem to be stuck at org.apache.tomcat.jni.Socket.sendbb(Native method) i.e network I/O. At most, these long-running downloads take 5 minutes, which I strongly suspect is because of the default 300 second timout in Apache 2.2 (http://httpd.apache.org/docs/2.2/mod/core.html, "TimeOut directive"). To me, this looks like network problems. The Apache timeout (if that is what is kicking in at the 5 minute mark) indicates that ACK packets are not being transmitted correctly. My questions are what could be causing this? Closed browser at receiving end but socket not signaled as closed properly? Packet loss or some other network failure in transit? Where would I start troubleshooting this? We're running Tomcat and Apache on Windows server 2008-R2 in a vmware virtualized server.

  Read the article

• Should I use "Raid 5 + spare" or "Raid 6"?

  - by Trevor Boyd Smith

  What is "Raid 5 + Spare" (excerpt from User Manual, Sect 4.17.2, P.54): RAID5+Spare: RAID 5+Spare is a RAID 5 array in which one disk is used as spare to rebuild the system as soon as a disk fails (Fig. 79). At least four disks are required. If one physical disk fails, the data remains available because it is read from the parity blocks. Data from a failed disk is rebuilt onto the hot spare disk. When a failed disk is replaced, the replacement becomes the new hot spare. No data is lost in the case of a single disk failure, but if a second disk fails before the system can rebuild data to the hot spare, all data in the array will be lost. What is "Raid 6" (excerpt from User Manual, Sect 4.17.2, P.54): RAID6: In RAID 6, data is striped across all disks (minimum of four) and a two parity blocks for each data block (p and q in Fig. 80) is written on the same stripe. If one physical disk fails, the data from the failed disk can be rebuilt onto a replacement disk. This Raid mode can support up to two disk failures with no data loss. RAID 6 provides for faster rebuilding of data from a failed disk. Both "Raid 5 + spare" and "Raid 6" are SO similar ... I can't tell the difference. When would "Raid 5 + Spare" be optimal? And when would "Raid 6" be optimal"? The manual dumbs down the different raid with 5 star ratings. "Raid 5 + Spare" only gets 4 stars but "Raid 6" gets 5 stars. If I were to blindly trust the manual I would conclude that "Raid 6" is always better. Is "Raid 6" always better?

  Read the article

• How does one skip "Windows did not shut down successfully" in Win7-64?

  - by XenonofArcticus

  Migrating an app from an expensive and unreliable dedicated embedded x86 box running WinXP-embedded to COTS hardware (Dell E6410 laptop) running normal Win7-64. At this time, it's not feasible to deploy using Windows 7 embedded. The problem is, that the system is still sort of "embedded". The power could shut off at virtually any time without prior warning. We've stripped the OS down and removed the battery capability so that it will power down as desired. The app never writes to the disk, so it's not like we're going to corrupt anything terribly. The system is essentially idle after our app is up and running (with the exception of some computation, graphics, and TCP/IP and serial communications) so the OS enters a pretty stable state rather quickly. After a power-loss however, it rightly complains that Windows did not shut down successfully and presents the user with the Windows Error Recovery text screen. If left alone, it does eventually move on booting just fine, but we'd like to skip that step if possible. WinXP-embedded is designed to do this automatically, so I know it's possible. I've looked at the Kernel Switches but I didn't see anything documented for "Skip Windows Error Recovery". I've also read extensively on the startup process: http://homepage.ntlworld.com./jonathan.deboynepollard/FGA/windows-nt-6-boot-process.html I know I can disable the auto chkdsk in the registry, but that's not the same thing either. So, how do I streamline the boot process to not hassle the user about a situation that will be the regular normal situation?

  Read the article

• Method to integrate Powershell scripts with non-Windows workflow?

  - by Matt Simmons

  I love the smell of new machines in the morning. I'm automating a machine creation workflow that involves several separate systems across my infrastructure, some of which involve 15 year old perl scripts on Solaris hosts, PXE Booting Linux systems, and Powershell on Windows Server 2008. I can script each of the individual parts, and integrating the Linux and Unix automation is fairly straightforward, but I'm at a loss as to how to reliably tie together the Powershell scripts to the rest of the processes. I would prefer if the process began on a Linux host, since I imagine that it will end up as a web application living on an Apache server, but if it needs to begin on Windows, I am hesitantly okay with that. I would ideally like something along the lines of psexec for Linux to run against Windows, but the answer in that direction appears to by Cygwin, and as much as I appreciate all of the hard work that they put in, it has never felt right, if you know what I mean. It's great for a desktop and gives a lot of functionality, but I feel like Windows servers should be treated like Windows servers and not bastardized Unix machines (which, incidentally, is my argument against OSX servers, too, and they're actually Unix). Anyway, I don't want to go with Cygwin unless that's the last and only option. So I guess what I'm asking is if there is a way to execute jobs on Windows machines from Linux. Without Cygwin. I'm open to ideas and suggestions, including "Look idiot, everyone uses Cygwin, so suck it up and deal with it". Thanks in advance!

  Read the article

• Simplest DNS solution for remote offices

  - by dunxd

  I look after a bunch of remote offices that connect via VPN - a Cisco ASA 5505 in each office acts as Firewall and VPN end point. Beyond that we keep things as simple as possible in the offices to minimise the support burden. We don't have any kind of server except in offices large enough to justify having someone dedicated to IT. Basically there is the ASA, some computers, a network printer and a switch. One of the problems I am seeing in a lot of offices is that DNS requests looking up hosts inside our network often fail - I'm assuming timeouts due to the offices internet connection (they are all in developing world countries) having some sub-optimal qualities (e.g. high latency caused by VSAT segments, or packet loss. The obvious solution to this is to have some sort of local DNS service that can serve local requests - so I think it would need to do zone transfers from our Microsoft Windows 2008 R2 DNS servers at HQ. However, simply installing Windows Servers in each office is both expensive, and creates a support burden. This got me thinking about pfsense/m0n0wall on embedded devices - those can act as a DNS server, and could be configured at HQ and sent out as just something that needs to be plugged into the network and can then be forgotten about by the staff locally. Maybe there are some alternatives to the ASA 5505 that include some DNS functionality. Has anyone here dealt with the problem, either using some kind of embedded device, or found some other solution? Any gotchas or reasons to avoid what I have suggested?

  Read the article

• Cannot Connect to VSFTP outside of network

  - by jnolte

  I am having a hair pulling issue with my VSFTPD. I am not sure where to turn and I have went through to make sure everything is working properly and when trying to connect to ftp using ftp localhost I am able to login with the username and password I have specified. When I try to connect from outside I get the prompt Connected to domainname.com. but no prompt for user and password in addition when using an FTP client it hangs up and never connects. The server is running Ubuntu 12.04 LTS and VSFTPD 2.3.5 Here is the output of running iptables -L : http://pastie.org/4892233 Here is he output when running ps -FC vsftpd : root 14343 1 0 1168 984 3 16:55 ? 00:00:00 /usr/sbin/vsftpd Here is output of running netstat -tlpn | grep vsftpd : tcp6 0 0 :::21 :::* LISTEN 14343/vsftpd I have uninstalled and reinstalled many times and tried several different configurations and am at a complete loss on why this may not be working. We very often use the same configuration on the same type of servers with no issues. Thank you in advance for your help.

  Read the article

• Power issues Foxconn Barebones kit

  - by alpha1

  I have a Foxconn R20D2 bought about a year and a half ago. It ran fine for a while and then around last summer it started having power issues. I chalked it up to changes in electric current due to the overwhelmed grid when people turn on their AC units, but this problem has stayed for all year, shutting off randomly, shutting off when i turn on a vacuum and similar problems. Now that its summer again, the box basically sits there all day cycling itself, and now has gotten to the point it tried to boot and after 3 seconds, fails, shuts off and tried again. I know its power related, it runs opensuse linux and there are never any shutdown logs or anything of that sort. As the weather got hotter i noticed it happening more and more, and it most often happened in the morning, i presume as people woke up and turn on the AC. The power supply is a Chennel well technology co LTD model DSL-150. 150W max output. Its an intel atom dual core, with 2 sata drives, no CD/floppy etc, recently upgrades from 2 to 4gb of ram. It runs at 104 degrees Fahrenheit all the time almost. Any way i can test the power supply or anything else to try to fix it? Im a software guy, not hardware so im at a complete loss here, thanks for all assistance you can provide! EDIT: The switch on the back that says 230 or 115 is set to 230. If im in the USA, could that be causing the problems?

  Read the article

• How to prevent asymmetric routing with multiple eBGP routers?

  - by Andy Shinn

  I have 2 routers announcing a /22 subnet to different providers (one providers connects to each of the 2 routers). I have split the /22 in two /23 to announce one /23 on each of the routers plus the /22 (the providers will take the more specific route). This allows me to fail over and keep traffic inside the /23 in and out the same provider. What are other ways in which I could announce just the /22 with both routers and have packets from servers on the network behind the routers go back out the same router in which they came in from? EDIT: The main problem I come across, which end users and clients complain about the most, is that the least hop route is sometimes not the "optimal" route. In my case, I know that Provider B may have better latency to X nation. But when packets come in from provider B, they may go out Provider A or provider B. The reverse is also true. If I send a packet to X nation out provider A, even though it may have more hops back, the packet will likely come in from Provider B (which may have higher latency, packet loss, etc. to this nation)

  Read the article

• Mysterious Windows 7 slowdown problem

  - by cletus

  I have a fairly beefy machine: Intel Q9450 8GB DDR2800 (4x2) Intel X25-M G2 80GB SSD Several other hard drives Windows 7 Ultimate 64 In the last month I've gotten a mysterious slowdown problem. When I start my IDE (IntelliJ IDEA) it usually takes about 20 seconds on the SSD. If my machine has been on for a day or two (as far as I can tell this is the only pattern) and I try to start the IDE, it brings my machine to a halt. CPU usage goes up to 25% per core (so it's basically 100% usage) and it takes up to 5 minutes to start. Other things I've noticed: iTunes will start to skip and stutter (my music is running off a second hard drive). The only persistent things I'm running are: AVG Anti-Virus Spybot (the slowdown predates this) Hamachi and Murmur (again the slowdown predates this) Apple Airport Base Agent HP OfficeJet 8500 driver/manager The browser I use is Chrome. I can't think why that'd be relevant but it's always on so I thought I'd mention it. When this happens I can't see a reason for it in the process list. No CPU hogs. No spikes in IO activity that I can see. Basically I'm at a loss to explain it and need to reboot, at which point everything returns to normal (for awhile). FWIW the Intel SSD is about 75-80% full. I know being too full can really degrade performance. I don't believe that's the issue here. Does anyone have any ideas on what I can do to fix this or at least help find what's going wrong? This same machine (sans SSD) could run Win XP and stay up fine for a month or two.

  Read the article

• (Mac Intel) HP PS driver prints in B&W from Adobe Reader after installing Cannon PS driver

  - by John B

  I have a unique problem that leaves me at a loss as to where to start troubleshooting. We have three Macs we use for graphics, two of which are PowerPC and one which is Intel. They are set up to print to an HP 5500dn, but occasionally this printer gets tied up with a massive print job, so I installed the PS driver (iR-PSv1.81MacOSX) for the Cannon C3200 Printer/copier on each of the machines. Both of the PowerPC Macs installed without issue, but the Intel Mac exhibits strange behavior: I've confirmed that while the Cannon driver is installed (whether or not the Cannon is set up for printing in print settings), the HP 5500dn will print in color from Safari, but only prints in black and white from Adobe Reader. The Cannon printer itself has not exhibited any strange behavior As soon as the Cannon driver is uninstalled, the HP 5500dn prints in color from Adobe Reader again. We run a network of Windows PCs, and the 'Mac room' mostly takes care of itself, so we don't have any experienced Mac administrators onsite. The Cannon is capable of Appletalk, but the PS driver seemed easier to work with (and Appletalk is currently disable on the Cannon. I'm not against using the Appletalk compatible drivers, but I would rather use the PS driver if at all possible - I don't want to open up the proverbial can of worms. If someone has any clues or suggestions that would help troubleshoot this problem, I would be grateful. I've already done some googling, but due to the obscure nature of this problem, I haven't been very successful.

  Read the article

• Unable to connect via NetBIOS Name

  - by grom

  I can't connect to machines/shares by NetBIOS names. Below is console output showing the problem. C:\>nbtstat -n Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] NetBIOS Local Name Table Name Type Status --------------------------------------------- BEAST <00> UNIQUE Registered WORKGROUP <00> GROUP Registered BEAST <20> UNIQUE Registered WORKGROUP <1E> GROUP Registered WORKGROUP <1D> UNIQUE Registered ..__MSBROWSE__.<01> GROUP Registered C:\>nbtstat -A 192.168.1.3 Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] NetBIOS Remote Machine Name Table Name Type Status --------------------------------------------- BRCLAPTOP <00> UNIQUE Registered WORKGROUP <00> GROUP Registered BRCLAPTOP <20> UNIQUE Registered WORKGROUP <1E> GROUP Registered MAC Address = 00-1C-BF-14-B8-6E C:\>ping beast Pinging beast [fe80::59b8:179f:b90b:a63f%11] with 32 bytes of data: Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Ping statistics for fe80::59b8:179f:b90b:a63f%11: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\>ping brclaptop Ping request could not find host brclaptop. Please check the name and try again. C:\>nbtstat -a brclaptop Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] Host not found.

  Read the article

• How do I access my samba drive through several layers of network topology?

  - by stephenmm

  I have a new windows 7 Home Premium machine that is in a different room than my main computer area. As such I have to use a bridge and another router. Everything is working wonderfully except I cannot access the SAMBA drive with the new machine. I know that SAMBA is accessible as an older WinXP machine can access it. A picture of my network would probably be helpfull: To ISP | | +---------------------------+ | WAN | | Cable Modem | | (2WIRE678) | | | | | +---------------------------+ | +---------------------------+ | | (|) (|) +-----------+ | Belkin Router | | | | Wireless | | (F5D) |--+ +--| WinXP | | | |SAMBA USER | | | +-----------+ +---------------------------+ | | | | +------------+ | | Ubuntu | | | Apache + | | |SAMBA Server| | +------------+ | | +---------------------------+ | | | Netgear Bridge | | (XET1001) | | | +---------------------------+ # # +---------------------------+ | | | Netgear Bridge | | (XET1001) | | | +---------------------------+ | +---------------------------+ | | | D-Link Router | | (DI-524) | | | | | +---------------------------+ | | | | +-----------+ | | | Win7 | |SAMBA USER?| +-----------+ More interesting data points: 1. I can ping the SAMBA server from the Win7 machine locally (Ie. 192.168.2.2) 2. I can access the webserver from the Win7 machine locally (Ie. 192.168.2.2) 3. I followed the advice to get Win7 and SAMBA to play nice: http://www.tannerwilliamson.com/2009/09/windows-7-seven-network-file-sharing-fix-samba-smb/ Sorry for being so long winded but it is kind of complex and I am really at a loss as to how to fix it. If any of you have some suggestions I would love to hear it!

  Read the article

• Macros in Excel 2010 hangs

  - by Ahmad

  I have a spreadsheet with several macros. Generally, when previously using Excel 2007, a user clicks a button and everything works as expected (calculations, some email sending & file I/O). Typically, the expected run-time is about 90 seconds. The spreadsheet is a xlsm file created with Excel 2007. With Excel 2010 however, the same user process results in a non-responsive excel and forces us to kill excel from the task manager. Some note that I have gathered so far in trying to debug this issue: When monitoring CPU usage, it seems that Excel does start the macro. CPU usage increases as expected to about 47% for a few seconds. Excel.exe than drops to 0% usage and I now have a non-responsive Excel (even after 1 hour). If I set debug break points across modules and different functions and step through the code (after clicking the button) , the process works as expected albeit much slower. To add, there were no exceptions. I am at a complete loss as to what the issue may be. I initially thought it may be the add in that is being used but that was debunked by point 2. This seems to be a very odd situation. I can provide more information if required, but I'm at wits end about the root cause could be. I need help in diagnosing and resolving this issue.

  Read the article

• NTFS frequent corruption when writing many small files, index $I30 error

  - by david sedai

  I'm running Windows 7 Ultimate on a laptop with a 500G HDD, and had all partitions formatted as NTFS. I do a lot of programming and LaTeX typesetting, both of these involves a large amount of reading/writing/deleting to a lot of small files, such as C++ library headers or LaTeX packages. The problem is that frequently, when there is a large number of writing to files, the partition being written to often corrupts, the chkntfs e: returns dirty, where e: is the partition being written. I've re-formatted the drive, I've contacted the laptop manufacturer and had the HDD checked, the HDD is not faulty, there are no bad sectors, and I've tried a brand new HDD, to no avail, and the other partition on the same physical drive doesn't have this issue. I'm pretty sure that it's no hardware related. I've searched the Microsoft support pages, one page http://support.microsoft.com/kb/982018 provides an update for Advanced Format Disks, which I've already installed. The chkntfs log shows $130 index errors. I'm at a loss here. Can anyone help? Thanks in advance.

  Read the article

• Configure static IPv6 on Ubuntu

  - by Charles Offenbacher

  I'm trying to configure IPv6 on a dedicated Ubuntu server. My provider gave me a "/64" (whatever that is - I'm still confused) of IPv6 addresses. However, when I try to use them, I can't ping anything. What do I do? :( # ping6 ipv6.google.com PING ipv6.google.com(vx-in-x63.1e100.net) 56 data bytes From fe80::219:d1ff:fefb:42d8 icmp_seq=1 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=2 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=3 Destination unreachable: Address unreachable --- ipv6.google.com ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2014ms # tracepath6 ipv6.google.com 1?: [LOCALHOST] 0.025ms pmtu 1500 1: fe80::219:d1ff:fefb:42d8%eth0 2000.022ms !H Resume: pmtu 1500 # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 64.***.***.*** netmask 255.255.255.248 gateway 64.***.***.*** iface eth0 inet6 static pre-up modprobe ipv6 address 2607:F878:1:***::1 netmask 64 gateway 2607:F878:1:***(same as address)::1 # ifconfig eth0 Link encap:Ethernet HWaddr 00:19:d1:fb:42:d8 inet addr:64.***.***.*** Bcast:64.***.***.*** Mask:255.255.255.248 inet6 addr: fe80::219:d1ff:fefb:42d8/64 Scope:Link inet6 addr: 2607:f878:1:***::1/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:52451 errors:0 dropped:0 overruns:0 frame:0 TX packets:39729 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6817761 (6.8 MB) TX bytes:6153835 (6.1 MB) Interrupt:41 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:166 errors:0 dropped:0 overruns:0 frame:0 TX packets:166 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:31714 (31.7 KB) TX bytes:31714 (31.7 KB)

  Read the article

• How to configure Windows user accounts for ODBC network with NT authentication?

  - by Ian Mackinnon

  I'm trying to create a connection to an SQL Server database from the ODBC Data Source Administrator using "Windows NT authentication using the network login ID". Both server and client are running Windows XP. It appears that any account with administrator privileges can add the data source on the server*, though connection attempts from the client result in error messages that suggest it is trying to authenticate using a guest account. I found a Microsoft support page that says: For SQL Server...: connect using the impersonated user account. But it doesn't offer advice about how to do that. How do I impersonate a user account on the server? or (since it sounds like that would lead to an unfortuante squashing of privileges and loss of accountability): How do I give an account on the client privileges on the server database and then ensure the client attempts authentication with the privileged account and not with a guest account? I'm aware that I'm providing rather sparse information. This is because I'm in unfamiliar territory and don't know what's pertinent. I'll attempt to add any requested information as quickly as possible. *I'm planning on tightening privileges straight after I get it working as it stands.

  Read the article

• LDAP Account Locked Out Sporadically after Password change - Finding the source of invalid attempts

  - by CityView

  On a small network of machines (<1000) we have a user whose account is being locked out after an indeterminate interval following a password change. We are having severe difficulties finding the source of the invalid logon attempts and I would appreciate it greatly if some of you could go through your thought process and the checks you would perform in order to fix the problem. All I know for sure is that the account is locked out several (5+) times a day, I can't even be sure it's due to failed login attempts as there is no record of failure until the account is locked. So far I have tried; Logging the account out of everything we can think of and back in with the new password Scanning the user's box for any non standard software which might perform an LDAP lookup Checking all installed services on our production boxes to check none are attempting to run under the account Changing the user back to their old password (Problem persists so perhaps password change is a red herring) Wireshark on a box where lots of LDAP authentication is performed - Rejects only occur after account is already locked out Clearing the credential cache in - Control Panel - User Accounts - Advanced Looking at the local I'm at a loss for what to try. I am happy to try any suggestions you have in order to diagnose the issue. I think my question boils down to a simple request; I need a technique for deriving the source (Application/Host) of the invalid login attempts which are causing the account to be locked. I'm not sure if that's even possible but I suspect there must be more I can try. Many thanks, CityView

  Read the article

• Should an HA failover occur in this scenario?

  - by joeqwerty

  I'm running vSphere 5 in an HA cluster across two hosts (vsphereA and vsphereB). I have the HA cluster configured for host monitoring and datastore heartbeat monitoring with admission control disabled (hopefully I rightfully understand that datastore heartbeat monitoring prevents inadvertent and unwanted HA failovers due to management network isolation). Each host has a single connection to a dedicated iSCSI network and iSCSI target (no MPIO). All vmdk's for all VM's exist on the iSCSI datastore. As a test of HA I disconnected the iSCSI connection on vsphereB and was surprised to see that the running VM's on vsphereB continued to run on vsphereB. The powered off VM's were showing as inaccessible (which I expected due to the fact that they weren't running and the connection from vsphereB to the iSCSI target was severed) but the running VM's continued to run and continued to be "owned" by vsphereB. I expected to see an HA failover occur for those VM's and expected to see them "owned" by vsphereA after the HA failover (which didn't occur). I'm at a loss to understand why an HA failover didn't occur for those VM's. Am I misunderstanding in which cases an HA failover should occur?

  Read the article

• LDAP groups not applying to filesystem permissions

  - by BeepDog

  System is ArchLinux, and I'm using nss-pam-ldapd (0.8.13-4) to connect myself to ldap. I've got my users and some groups in LDAP: [root@kain tmp]# getent group <localgroups snipped> dkowis:*:10000: mp3s:*:15000:rkowis,dkowis music:*:15002:rkowis,dkowis video:*:15003:transmission,rkowis,dkowis,sickbeard software:*:15004:rkowis,dkowis pictures:*:15005:rkowis,dkowis budget:*:15006:rkowis,dkowis rkowis:*:10001: And I have some directories that are setgid video so that the video group stays, and they're configured g=rwx so that members of the video group can write to them: [root@kain video]# ls -ld /srv/video drwxrwxr-x 8 root video 208 Oct 19 20:49 /srv/video However, members of that group, say dkowis cannot write into that directory: [root@kain video]# groups dkowis mp3s music video software pictures dkowis Total number of groups that dkowis is in is like 7, I redacted a few here. [dkowis@kain wat]$ cd /srv/video [dkowis@kain video]$ touch something touch: cannot touch 'something': Permission denied [dkowis@kain video]$ groups dkowis mp3s music video software pictures I'm at a loss as to why my groups show up in getent groups, but my filesystem permissions are not being respected. I've tried making a new directory in /tmp and setting it's group permissions to rwx, and then trying to write a file in there, it doesn't work. The only time it does work is if I open it wide up allowing o=rwx. That's obviously not what I want, and I'm not able to figure out what my missing piece is. Thanks in advance.

  Read the article

< Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >