Search Results

Search found 14989 results on 600 pages for 'street address'.

Page 491/600 | < Previous Page | 487 488 489 490 491 492 493 494 495 496 497 498  | Next Page >

• Assistance on setup to Connect an offsite server to the LAN via RRAS VPN - Server 2008 R2

  - by Paul D'Ambra

  I have an office LAN protected using a Zyxel Zywall USG 300. I've set up an L2TP/ipsec VPN on that which accepts connections using a shared secret and I've tested this from multiple clients. I have a server offsite and want to set up RRAS to use a persistent connection to the VPN so that it can carry out network jobs even with no one logged in (I'm using it for Micorosft DPM secondary backup). If I create a vpn as if I were setting up a users laptop it can dial in no problem but if I set up a demand dial interface in RRAS it errors. I enable RRAS ticking only demand dial interface (branch office routing) Select network interfaces, right click and choose new demand dial interface Name the VPN ToCompany Select connect using VPN And then L2TP as the vpn type enter the IP address (double-checked for typos!) select Route IP packets on this interface specify static route to remote network as 10.0.0.0/24 with metric of 1 add dial out credentials (again double checked for typos and confirmed with other vpn connections click finish now I right-click on the new interface and choose properties and then the security tab I change Data encryption to optional select only PAP for Authentication (both as per manufacturer of Zywall) click advanced settings against type of vpn and set shared secret then I select the new interface, right-click and choose connect this dials and then errors with either 720 or 811 as the error codes. However, if I create a VPN by going to Network & Sharing center and setting up as if I was creating a VPN from my laptop to the office (say) it dials successfully so I know the VPN settings are correct and the machine can connect to the VPN. Suggests very strongly the problem is how I'm setting up RRAS. Can anyone help?

  Read the article

• Transparent proxying in MacOS X 10.6 Snow Leopard (and maybe FreeBSD)

  - by apenwarr

  I'm trying to create a transparent proxy on my MacOS machine in order to port the sshuttle ssh-based transproxy VPN from Linux. I think I almost have it working, but sadly, almost is not 100%. Short version is this. In one window, start something that listens on port 12300: $ while :; do nc -l 12300; done Now enable proxying: # sysctl -w net.inet.ip.forwarding=1 # sysctl -w net.inet.ip.fw.enable=1 # ipfw add 1000 fwd 127.0.0.1,12300 log tcp from any to any And now test it out: $ telnet localhost 9999 # any port number will do # this works; type stuff and you'll see it in the nc window $ telnet google.com 80 # any host/port will do # this *doesn't* work! After the latter experiment, I see lines like this in netstat: $ netstat -tn | grep ^tcp4 tcp4 0 0 66.249.91.104.80 192.168.1.130.61072 SYN_RCVD tcp4 0 0 192.168.1.130.61072 66.249.91.104.80 SYN_SENT The second socket belongs to my telnet program; the first is more suspicious. SYN_RCVD implies that my SYN packet was correctly captured by the firewall and taken in by the kernel, but apparently the SYNACK was never sent back to telnet, because it's still in SYN_SENT. On the other hand, if I kill the nc server, I get this: $ telnet google.com 80 Trying 66.249.81.104... telnet: connect to address 66.249.81.104: Connection refused telnet: Unable to connect to remote host ...which is as expected: my proxy server isn't running, so ipfw redirects my connection to port 12300, which has nobody listening on it, ie. connection refused. My uname says this: $ uname -a Darwin mean.local 10.2.0 Darwin Kernel Version 10.2.0: Tue Nov 3 10:37:10 PST 2009; root:xnu-1486.2.11~1/RELEASE_I386 i386 Does anybody see any different results? (I'm especially interested in Snow Leopard vs Leopard results, as there seem to be some internet rumours that transproxy is broken in Snow Leopard version) Any advice for how to fix?

  Read the article

• KVM error with device pass through

  - by javano

  I am running the following command booting a Debian live CD passing a host PCI device to the guest as a test and KVM errors out; kvm -m 512 -boot c -net none -hda /media/AA502592502565F3/debian.iso -device pci-assign,host=07:00.0 PCI region 1 at address 0xf7920000 has size 0x80, which is not a multiple of 4K. You might experience some performance hit due to that. No IOMMU found. Unable to assign device "(null)" kvm: -device pci-assign,host=07:00.0: Device 'pci-assign' could not be initialized lspci | grep 07 07:00.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 74) I shoved an old spare NIC into my motherboard to test PCI pass through. I have searched the Internet with Goolge and found that errors relating to "No IOMMU found" often mean the PCI device is not supported by KVM. Does KVM have to support the device being "passed-through"? I though the point was to pass the device through and let the guest worry about it? Ultimately I want to pass-through a PCI random number generator, is this not going to be possible with KVM? Thank you.

  Read the article

• PC won't PXE boot to WDS/MDT with Dell Optiplex 755

  - by Moman10

  I am trying to set up a basic MDT solution. I have set one up in the past at a previous job and it worked flawlessly, however here I'm running into a problem and am having no luck getting around it. I've installed Windows Server 2012 and MDT 2013, along with adding on the WDS role. I haven't configured much outside of the defaults for WDS, basically just set PXE response to respond to all clients (and unchecked admin approval). This machine does not run a DHCP server. I looked on the DHCP scope of our DHCP server, it shows options 66/67 checked and the server name of the WDS server is in there as well. I didn't add this but I assume it was put on during the install process (I believe I had to manually make some adjustments at my old job for this). The PC I have is a Dell Optiplex 755. I have enabled the onbard NIC w/PXE boot option in BIOS and attempted to boot. I get a "TFTP...." error but nothing offering out a DHCP address like I'm used to. In my previous job it pretty much worked right out of the box. I've verified that PortFast is enabled on the port and I've tried a couple different PCs (but both are the same model, only model I have to work with). No matter what, I get the same error. The subnet the PC is in is a different subnet than where the WDS server is sitting, but there are IP helper statements on the switch and the PCs can get regular DHCP addresses just fine from the DHCP server, just doesn't seem to get offered out a PXE boot option. I don't know if the problem is a configuration with the server or the PC itself...but after a few days of Googling I'm running out of ideas. Does anyone have a good idea of something it may be?

  Read the article

• Need help using a super scope

  - by Vdub

  I have a windows server 2008 r2 standard running our DCHP, DNS, and AD. also I have (3) HP Pro Curve 2510-G switches (J9280A). Right now our LAN is set up 192.168.50.2-192.168.50.254 on our sub-net (A) and another scope with 192.168.51.2-192.168.51.254 sub-net (B) both have sub-net mask of 255.255.255.0. The same server is our DNS which is 192.168.50.242 and our firewall (watchguard) is the gateway at 192.168.50.1. Right now the sub-net (B) does not have DHCP active so only sub-net (A) is giving a pool. My problem is that we are trying to have open WiFi on our network and i am assuming that i can use the sub-net (B) for that if i activate it and use sub-net (A) for our staff only. I have noticed that when i set up a static on a client pc and set it to 192.168.51.x i cannot use the DNS of 192.168.50.242 however i can use 8.8.8.8 and it works fine, i am guessing that because it is on a different sub-net? Forgive me as i am very new at this and dont know a lot. Is there easy way with the equipment i have to a accommodate wifi for hundreds of people without causing problems for our staff? (multiple same IP address assigns) I appreciate any and all info!

  Read the article

• Exchange Connector Won't Send to External Domains

  - by sisdog

  I'm a developer trying to get my .Net application to send emails out through our Exchange server. I'm not an Exchange expert so I'll qualify that up front!! We've set up a receive Connector in Exchange that has the following properties: Network: allows all IP addresses via port 25. Authentication: Transport Layer Security and Externally Secured checkboxes are checked. Permission Groups: Anonymous Users and Exchange Servers checkboxes are checked. But, when I run this Powershell statement right on our Exchange server it works when I send to a local domain address but when I try to send to a remote domain it fails. WORKS: C:\Windows\system32Send-Mailmessage -To [email protected] -From [email protected] -Subject testing -Body testing -SmtpServer OURSERVER (BTW: my value for OURSERVER=boxname.domainname.local. This is the same fully-qualified name that shows up in our Exchange Management Shell when I launch it). FAILS: C:\Windows\system32Send-Mailmessage -To [email protected] -From [email protected] -Subject testing -Body testing -SmtpServer OURSERVER Send-MailMessage : Mailbox unavailable. The server response was: 5.7.1 Unable to relay At line:1 char:17 + Send-Mailmessage <<<< -To [email protected] -From [email protected] -Subject testing -Body himom -SmtpServer FTI-EX + CategoryInfo : InvalidOperation: (System.Net.Mail.SmtpClient:SmtpClient) [Send-MailMessage], SmtpFailed RecipientException + FullyQualifiedErrorId : SmtpException,Microsoft.PowerShell.Commands.SendMailMessage EDIT: From @TheCleaner 's advice, I ran the Add-ADPermission to the relay and it didn't help; [PS] C:\Windows\system32Get-ReceiveConnector "Allowed Relay" | Add-ADPermission -User "NT AUTHORITY\ANONYMOUS LOGON" -E xtendedRights "Ms-Exch-SMTP-Accept-Any-Recipient" Identity User Deny Inherited -------- ---- ---- --------- FTI-EX\Allowed Relay NT AUTHORITY\ANON... False False Thanks for the help. Mark

  Read the article

• How can I make Internet Explorer 6 render Web pages like Internet Explorer 11?

  - by gparyani

  Now, I know that this may seem like a bad question in that I can just upgrade to Internet Explorer 8, but I am sticking with IE6 in that IE8 removes valuable features, like the ability to save favorites offline and the fact that a file path turns into a Windows Explorer window and typing a Web address into Windows Explorer changes it into an IE window. I know that Internet Explorer 6 does a really bad job at rendering some pages. I know of the Google Chrome Frame extension that brings Chrome-style rendering into IE, but that will soon be discontinued. So, I tried another thing: I know that C:\Windows\System32\mshtml.dll contains the Trident rendering engine that is used by IE, so I tried something: I first backed up the original file by renaming it on Windows XP to mshtml-old.dll, then I tried to copy in the DLL from a computer running Windows 7 with Internet Explorer 10. I noticed that, after copying, the system had replaced the new DLL with the old one, but left the one I backed up intact. Is there any way I can get the system to not replace the DLL like that so that I can transfer in IE11's mshtml.dll into Windows XP and make IE6 render like IE11? I'm looking for an answer that describes how to tweak my system to make IE6 render like IE11 (or IE10), not one that tells me to upgrade IE or install another browser. I don't care how tedious the method is, just as long as it works.

  Read the article

• My VPS host (rosehosting) sold me a domain name, but I can't get it to work

  - by Faisal Vali

  My VPS host (rosehosting) sold me a domain name, but I can’t get it to work. They sent me an email with the following (almost a month ago) DNS Servers (unless you ordered your own DNS servers): ns1.rosehosting.com (216.114.78.148) ns2.rosehosting.com (216.114.78.155) Operating System: Ubuntu 9.04 Domain Name: mytestdomainfv.com Host Name: mytestdomainfv.com IP Address: .... Physical Host Name: Vs####.rosehosting.com When I type in the Physical Host Name or the IP from a remote computer I get connected to my VPS. But when i type 'mytestdomainfv.com' the name is never resolved, and it has been a month now. I thought that they would configure it so that it would, but it seems that they haven't. Does anyone know how I can get 'mytestdomainfv.com' to point to my VPS? I looked at some of the other similar questions, but they talk about forwarding GoDaddy domain names - so I'm not sure if it applies - but then again, it might just be my naivete. Any direction will be greatly appreciated. Thanks! p.s mytestdomainfv.com is not the real domain name

  Read the article

• DNS requests failing from computers that can ping DNS server

  - by dunxd

  I have a situation where computers in some of our remote offices from time to time lose the ability to use our DNS server (in head office) to resolve hostnames. The offices are connected via VPN using Cisco ASA 5505 (VPNclient config rather than Site to Site). Ping to the IP address of the DNS server works. But nslookup will get a "no response from server" message. Computers in other locations can use DNS fine. This is an intermittent problem. One day/hour it works, another it doesn't. Other offices connected in the same way work when another doesn't. No config changes have been made on routers around the time we see the problem. Some users have reported that the problem goes away after doing a repair connection in Windows XP. I think this could be caused by the DNS cache being flushed as part of this - the Windows DNS cache makes the intermittent problem look less so because it caches failed lookups as well as successful ones. However, it is possible some other aspect of Windows is involved. Windows 7 clients have also had the same problem. Any pointers on deeper troubleshooting, or anyone else found this?

  Read the article

• lighttpd with multiple IPs, each with a UCC certificate and many hostnames

  - by Dave

  I'd like to get lighttpd working with UCC certificates, but I can't seem to figure out the correct syntax. Essentially, for each IP address, I have one UCC certificate and a bunch of hostnames. $SERVER["socket"] == "10.0.0.1:443" { ssl.engine = "enable" ssl.ca-file = "/etc/ssl/certs/the.ca.cert.pem" ssl.pemfile = "/etc/ssl/private/websitegroup1.com.pem" $HTTP["host"] =~ "mywebsite.com" { server.document-root = /var/www/mywebsite.com/htdocs" } The above code works fine for one hostname, but as soon as I try to set up another hostname (note the same SSL cert): $SERVER["socket"] == "10.0.0.1:443" { ssl.engine = "enable" ssl.ca-file = "/etc/ssl/certs/the.ca.cert.pem" ssl.pemfile = "/etc/ssl/private/websitegroup1.com.pem" $HTTP["host"] =~ "anotherwebsite.com" { server.document-root = /var/www/anotherwebsite.com/htdocs" } ...I get this error: Duplicate config variable in conditional 6 global/SERVERsocket==10.0.0.1:443: ssl.engine Is there any way I can put a conditional so that only if ssl.engine is not already enabled, enable it? Or do I have to put all my $HTTP["host"]s inside the same $SERVER["socket"] (which will make config file management more difficult for me) or is there some entirely different way to do it? This has to be repeated for multiple IPs too (so I'll have a bunch of SERVER["socket"] == 10.0.0.2:443" etc), each with one UCC cert and many hostnames. Am I going about this the wrong way entirely? My goal is to conserve IP addresses when I have many websites that are related and can share an SSL certificate, but still need their own SSL-accessible version from the appropriate hostname (instead of a single secure.mywebsite.com).

  Read the article

• Problem IIS 7.0 Locking files durring upload

  - by viscious

  I am running a server 2008 with iis7 and the ftp addon on to iis 7.0 I have the ftp site configured and mostly working Except that about 70% of the time when transferring a file the upload will hang forever. If I disconnect the ftp client and reconnect and try to upload the same file I will get an error on the client saying the file is locked. I have to restart the ftp service to clear the lock. I fired up process explorer and did a search on the file in question and sure enough the ftp service has a lock on the file and it takes around 20 minutes to release the lock on its own (and sometimes longer). This lock stays around even after I disconnect the client. Like I said this only happens about 70% of the time, the other 30% of the time it goes through just fine. Things i have verified. -Not a firewall issue. Server is using passive port range 8000-9000 which is allowed on the firewall. -Not a nat issue, server has a globally rout-able ip address -all recommended/required updates installed I have 5 other servers in a very similar configuration and this is the only one i have problems with.

  Read the article

• How private is the Opera Turbo feature of Opera?

  - by Marcus V

  If I'm using Opera with the Opera Turbo feature turned on (always, not set to "automaticly"). Can anyone see what sites I'm visiting (except Opera of course ...)? Opera Turbo uses a proxy server, so it should be that way, but as a not very technical person I'm not sure. Why do I want this? Well: nowadays, at least in my country, more and more (legal) open Wi-Fi connections are available. In those environments I like to have more privacy protections. I don't mind if they can see my IP address, but I just want to hide as much as I can of what I am doing. BTW: I don't care that they can see the data transferred; it doesn't have to be that secret. I only want to hide the requested Internet site links. BTW: I know that Opera Turbo only works with non-secure websites (HTTP), but that's fine for me. I only want it to work with these sites. BTW: I'm not need this for illegal purposes; I only want this for privacy reasons.

  Read the article

• Set postfix to send email but not to receive them

  - by CodeShining

  I'm using Google Apps to handle personal email addresses for my domain name, and I set up the DNS as Google suggests. All works fine. Now since I need a SMTP to send emails from my e-commerce I installed Postfix on the server. It works fine when I send emails to any email address but it doesn't send to the same domain name, so let's say my domain is example.com, I set postfix using example.com, if I try to reset a password using [email protected] postfix doesn't send and instead reports on the mail.log Sep 20 01:09:52 ip-10-54-26-162 postfix/pickup[6809]: B09A3415D8: uid=33 from=<www-data> Sep 20 01:09:52 ip-10-54-26-162 postfix/cleanup[6854]: B09A3415D8: message-id=<20120920010952.B09A3415D8@ip-10-54-26-162.eu-west-1.compute.internal> Sep 20 01:09:52 ip-10-54-26-162 postfix/qmgr[30978]: B09A3415D8: from=<[email protected]>, size=4234, nrcpt=1 (queue active) Sep 20 01:09:52 ip-10-54-26-162 postfix/local[6856]: B09A3415D8: to=<[email protected]>, relay=local, delay=0.01, delays=0.01/0/0/0, dsn=5.1.1, status=bounced (unknown user: "myaccount") Of course it cannot find a local user "myaccount" since that account is on Google Apps... How can I tell Postfix to send the email and do not search for a local user?

  Read the article

• Measure Total Bandwidth for Billing

  - by TonyZ

  I am setting up a new network which customers will host their applications on. It needs to be able to scale out to a few hundred servers and each server will have several VMs on it. Right now in my test environment, after the telco router, we are using a Linux router/firewall which is then connected to a Layer 2 switch. Could be a layer 3 in the future. I need to track total bandwidth per VM for each machine, and I need to do it in a way that it is not part of the VM. Each VM will have a private class ip address which is Natted by the gateway, or we may eventually run more than firewall/reverse proxy off a layer 3 switch. So my thinking is that I can do it off of a promiscuous port on the switches, or at the gateway firewall. I would like to have an out of the box solution, preferably open source. Does anyone have suggestions on the easiest way to set this up, and the easiest tool to use. I have looked at the web sites for Nagios, Zenoss, Zabbix, ntops on the firewall, etc. It is hard to ascertain just from the web sites if they do exactly this or not. Obviously, performance is also somewhat key here. Anything running on the gateway should not drag it down doing traffic accounting. Thanks for any thoughts. Tony Zakula

  Read the article

• Strange focus bug in Firefox (chrome vs content)

  - by Marius

  Here is a strange bug I'm experiencing in Firefox: I can only use either the chrome, or the content, not both at the same time! For example, I can click on tabs and the toolbar icons, focus the search bar and write in it as well as the address bar, but if I try to click on anything in the content (eg a link or a textfield to write something), then nothing happens. The mouse pointer doesn't change either, it just stays a pointer when I hover over things, and the links I hover don't react either. But if I alt-tab to another program (or click on it in the taskbar), then back to Firefox, then I can use the area that I click on. So if I click somewhere on the webpage to get focus back to Firefox, then I can click on links and write things (like this text), but I cannot click on tabs or refresh or anything else in the chrome. I can't even click on the minimize, restore and close icons! To get focus back on the chrome I have to alt-tab to another program, and then click on the chrome to get back to Firefox to be able to use the chrome again. I've tried closing and starting it again, but the bug is still there. I have experienced this before, but I don't remember what I did to fix it. This bug seems to occur sometimes when I wake up the computer from standby, but I leave by computer in standby all the time, so that is not the only factor.

  Read the article

• OpenWRT + OpenVPN client forwarding from lan to vpn not working

  - by Dariusz Górecki

  I've OpenWRT router with Backfire 10.03.1-rc3 (arch:brcm 2.6 kernel) I've set up an OpenVPN client connecting my router with workplace lan, and it works nicely, I can connect from router to networks (several) in workplace. My OpenVPN client uci-config looks like: config 'openvpn' 'stream_client' option 'nobind' '1' option 'float' '1' option 'client' '1' option 'reneg_sec' '0' option 'management' '127.0.0.1 31194' option 'explicit_exit_notify' '1' option 'verb' '3' option 'persist_tun' '1' option 'persist_key' '1' list 'remote' 'remote.address.cutted' option 'ca' '/lib/uci/upload/cbid.openvpn.stream_client.ca' option 'key' '/lib/uci/upload/cbid.openvpn.stream_client.key' option 'cert' '/lib/uci/upload/cbid.openvpn.stream_client.cert' option 'enable' '1' option 'dev' 'tun1' I've set the 'STREAM_VPN' Zone to allow in/out traffic, and I've added rules for zone-to-zone lan<-vpn and vpn<-lan config 'zone' option 'name' 'stream_vpn' option 'network' 'stream_vpn' option 'input' 'ACCEPT' option 'output' 'ACCEPT' option 'forward' 'REJECT' config 'forwarding' option 'src' 'lan' option 'dest' 'stream_vpn' config 'forwarding' option 'src' 'stream_vpn' option 'dest' 'lan' And interface config: config 'interface' 'stream_vpn' option 'proto' 'none' option 'ifname' 'tun1' option 'defaultroute' '0' option 'peerdns' '0' Now, from my router everything works nicely, the problem is that I cannot connect from computer inside a lan to hosts in networks provided by vpn connection :/ What I've missed, or what I'm doing wrong? And how can I force using specified DNS when connected to vpn? (I know that sever should use PUSH DNS option, but is PUSHes only routes)

  Read the article

• One-To-Many Powershell Scripts

  - by Matt

  I'm trying to create a script to run as a scheduled task, which will run against multiple servers and retrieve some information. To start with, I populate the list of servers by querying AD for all servers that match a certain set of criteria, using Get-ADComputer. The problem is, the list is returned as an object, which I can't then pass to the New-PSSession list. I have tried converting it to a comma-seperated string by doing the following: foreach ($server in $serverlist) {$newlist += $server.Name + ","} but this still doesn't work. the alternative is to iterate through the list and run the various commands against each server one at a time, but my preference would be to avoid this and run them using one-to-many remoting. UPDATE: To clarify what I want to end up being able to do is using -ComputerName $serverlist, so I want $serverlist to be a string rather than an object. UPDATE 2: Thanks for all the suggestions. Between them and my original method I'm starting to wonder whether -ComputerName can accept a string variable? I've got varying degrees of success getting the list of computers converted to a comma separated string, but no matter how I do it I always get invalid network address.

  Read the article

• pxe boot dos 7.x / 8.x on modern mainboard without floppy controller

  - by GitaarLAB

  How to pxe boot MS DOS 7.x / 8.x on a modern pc (mainboard without floppy controller) without using an external usb floppy drive? MS DOS 6.22 and earlier or other flavors pxe boot just fine on floppy-less hardware. But DOS 7.x and 8.x renders an error on boot: "Type the name of the Command Interpreter (e.g., C:\WINDOWS\COMMAND.COM) I read somewhere during research this was a rather unknown error, that started to become more common due to the advent of floppy-controller-less hardware. On some hardware (bios dependent) one could plug a usb-floppy-drive in the computer before booting (but that MIGHT also require it to be a "golden floppy drive" (as they where called back then). From a russian site (I read about a year ago and cannot find the hyperlink) MS-Dos versions 6.22 did some-kind of floppy-drive reset during initialization and since it couldn't connect to the floppy-host thus the error. How can I resolve this (without a physical external usb floppy)? Might there be some kind of virtual floppy-driver that could resolve this (for example to be loaded before the dos image loads)? Or could someone point me into the right direction (maybe even a hex-address and some further explanation or something)? I'm using syslinux by the way.

  Read the article

• Is timeout in tracertoutput an indication of an error?

  - by nitramk

  TCP/IP packages sent from my computer to a remote server does not always reach destination and ends up being retransmitted sometimes several times before they succeed. To troubleshoot this, I'm running a tracert to the server: Tracing route to <site> [<address>] Over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms mymachine 2 <1 ms <1 ms <1 ms gw.levonline.com [217.70.32.30] 3 <1 ms <1 ms <1 ms 81.201.213.218 4 <1 ms <1 ms <1 ms bmf1-hmf1.driften.net [81.201.213.12] 5 <1 ms <1 ms <1 ms 10ge-2-4-cr2.a1.sth.ownit.se [84.246.88.157] 6 <1 ms * <1 ms netnod-ix-ge-b-sth-4470.microsoft.com [195.69.11.181] 7 26 ms * * ge-3-0-0-0.ams-64cb-1a.ntwk.msn.net [207.46.42.1] 8 48 ms 57 ms 56 ms ten9-1.lts-76e-1.ntwk.msn.net [207.46.42.133] 9 * * * Request timed out. In step 6 and 7, I'm seeing timeouts while waiting for the reply from the server (as seen above). Running the same tracert many times gives varying output, sometimes the response is fine, but sometimes I get this timeout 1, 2 and sometimes for all 3 packets. The timeout always starts at the same server, netnod-ix-ge-b-sth-4470.microsoft.com. I've tried setting the tracert timeout to 10 seconds, but am still getting the timeout. Running tracert towards other servers does not give me the same timeout. Microsoft network technicians tells me that the problem is not on "their" side. Are these timeouts an indicator of a lost packet on the specific node which did not respond? Are the timeouts an indication of there being a problem, or is it normal?

  Read the article

• Diagnosing a BSOD involving USB

  - by David Ebbo

  [Running Win7 Ultimate 64 bit] My new HP Pavilion Elite HPE-450t has been plagued by BSDO crashes since I got it about 5 weeks ago. The crashes are somewhat rare, sometimes not occurring for 3 or 4 days. I have spent a lot of time trying to isolate the device that could be at fault, but I have seen crashes with only the keyboard and mouse plugged in (as USB devices), and I tried two sets of keyboard/mouse, so I'm running out of ideas. :( The WhoCrashed tool gave this info about my latest BSOD: crash dump file: C:\Windows\Minidump\121310-11887-01.dmp This was probably caused by the following module: usbport.sys (USBPORT+0x2DE4E) Bugcheck code: 0xFE (0x5, 0xFFFFFA8008F571A0, 0x80863B34, 0xFFFFFA80092F2510) Error: BUGCODE_USB_DRIVER file path: C:\Windows\system32\drivers\usbport.sys product: Microsoft® Windows® Operating System company: Microsoft Corporation description: USB 1.1 & 2.0 Port Driver Bug check description: This indicates that an error has occurred in a Universal Serial Bus (USB) driver. The crash took place in a standard Microsoft module. Your system configuration may be incorrect. Possibly this problem is caused by another driver on your system which cannot be identified at this time. I looked at http://msdn.microsoft.com/en-us/library/ff560407(VS.85).aspx, and for Parameter1 = 0x5, it says "A hardware failure has occurred due to a bad physical address found in a hardware data structure. This is not due to a driver bug". Should I conclude that it's a hardware issue in the machine itself, rather than a bad USB driver or USB device? Here is the MiniDump, in case someone can get more info out of it: http://ewt52q.blu.livefilestore.com/y1peS4Ce8nSK1SXghzMDoxDWXlaEu-EKCJsv25y8y5DXXIUzZ9U0_tYgFJXd939fykwa0zRmx98IW0PYG18GioqKAuARYjtspSA/121310-11887-01.dmp?download&psid=2

  Read the article

• slicehost google apps mx settings

  - by Bob

  Hello All, I am banging my head against the wall on this one. I followed the MX setup tutorials for Google Mail and it didn't work. Currently, after deleting those records and adding the ones google suggested I have domain.com. 86400 IN MX 10 ASPMX.L.GOOGLE.com. domain.com. 86400 IN MX 20 ALT2.ASPMX.L.GOOGLE.com. domain.com. 86400 IN MX 20 ALT1.ASPMX.L.GOOGLE.com. domain.com. 86400 IN MX 30 ASPMX2.GOOGLEMAIL.com. domain.com. 86400 IN MX 30 ASPMX5.GOOGLEMAIL.com. domain.com. 86400 IN MX 30 ASPMX3.GOOGLEMAIL.com. domain.com. 86400 IN MX 30 ASPMX4.GOOGLEMAIL.com. according to the output of my dig command for my particular "domain". I can send email from google apps mail but I can not recieve any email. It gives me the following error: Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550 #5.1.0 Address rejected [email protected] Now I already tried following the slicehost MX article instructions straight as well and they did not work out for me. The domain has already been verified by google and it says the email is activated from their end. Any help would be appreciated : )

  Read the article

• Tripwire help Required

  - by ramaperumal

  I have created the policy file in Tripwire and also I have created the rules as well mentioned below: /opt/jboss/server/gis/conf -> $(SEC_CONFIG) +aipm +c+g+a+i+s+t+u+l+M; /usr/local/gtech/eseries/ -> $(SEC_CONFIG) +a+c+g+i+s+t+u+l+M ; After running the integrity check the output should be a(Access timestamp),c (Inode timestamp (create/modify),g (File owner's group ID),i (Inode number),s (File size),t (time stamp),u (File owner's user ID),l(File is increasing in size (a "growing file"),M (MD5 hash value). I am getting the output as below: [root@xxsi1242 tripwire]# tripwire --check Parsing policy file: /etc/tripwire/tw.pol *** Processing Unix File System *** Performing integrity check... Wrote report file: /var/lib/tripwire/report/xxsi1242.gtk.gtech.com-20131106-053812.twr Open Source Tripwire(R) 2.4.1 Integrity Check Report Report generated by: root Report created on: Wed 06 Nov 2013 05:38:12 AM EST Database last updated on: Wed 06 Nov 2013 05:31:17 AM EST =============================================================================== Report Summary: =============================================================================== Host name: xxsi1242.gtk.gtech.com Host IP address: 156.24.65.171 Host ID: None Policy file used: /etc/tripwire/tw.pol Configuration file used: /etc/tripwire/tw.cfg Database file used: /var/lib/tripwire/xxsi1242.gtk.gtech.com.twd Command line used: tripwire --check =============================================================================== Rule Summary: =============================================================================== ------------------------------------------------------------------------------- Section: Unix File System ------------------------------------------------------------------------------- Rule Name Severity Level Added Removed Modified --------- -------------- ----- ------- -------- Invariant Directories 66 0 0 0 Temporary directories 33 0 0 0 * Tripwire Data Files 100 0 0 1 Tech Stack 100 0 0 0 User binaries 66 0 0 0 Tripwire Binaries 100 0 0 0 * CLPS bins 100 0 0 2 CLPS Configuration files 100 0 0 0 ESCommon 100 0 0 0 Shell Binaries 100 0 0 0 OS executables and libraries 100 0 0 0 Security Control 100 0 0 0 ESCommon Configuration 100 0 0 0 (/etc/gtech/escommon) Total objects scanned: 12358 Total violations found: 3 =============================================================================== Object Summary: =============================================================================== ------------------------------------------------------------------------------- # Section: Unix File System ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- Rule Name: Tripwire Data Files (/etc/tripwire/tw.pol) Severity Level: 100 ------------------------------------------------------------------------------- Modified: "/etc/tripwire/tw.pol" ------------------------------------------------------------------------------- Rule Name: CLPS bins (/opt/jboss/server) Severity Level: 100 ------------------------------------------------------------------------------- Modified: "/opt/jboss/server/esapps1/data/hypersonic/localDB.lck" "/opt/jboss/server/gis/data/hypersonic/localDB.lck" =============================================================================== Error Report: =============================================================================== No Errors ------------------------------------------------------------------------------- *** End of report *** Note: In the output I only am getting the files which are modified. I need the detail output for this. But unfortunately I am not getting what I expected. Please help me to proced further.

  Read the article

• Can I use multiple URLs in the URL field of KeePass?

  - by Sammy

  I am using KeePass version 2.19. What I would like to do is have more than just one URL address associated with a given user name and password. The entry for a given website might look something like this... Title google User Name email Password pass URL https://accounts.google.com/ServiceLogin?hl=en&continue=https://www.google.com/ https://accounts.google.com/ServiceLogin?hl=sv&continue=https://www.google.com/ https://accounts.google.com/ServiceLogin?hl=de&continue=https://www.google.com/ As you can see the ?hl=en changes into ?hl=sv and then to ?hl=de for the three different languages in which I wish to view the Google log-in page. But this of course could be something completely different, like different web services from the same provider like YouTube and Gmail by Google. Very much like SE where you have several websites but only use one user name and password. I imagine something along the lines of having multiple entries for one and the same website, where KeePass would actually prompt you to choose which one you want to use. So you have several user names and passwords that use the same URL. But is it possible to have several URLs using the same user name and password, so that KeePass asks me "to which of the following three URLs do you want to auto-log into with this password"?

  Read the article

• I receive email not addressed to me - virus?

  - by Anne

  Every once in a while I receive email (on Gmail) that isn't addressed to me. Gmail puts it in the spam box, because it 'can't verify that it has been sent by [sender]'. The emails, when opened, contain confidential information about deliveries and paid bills (it does look an awful lot like 'real' mail from well-known companies, and it doesn't look like a scam, since the mail is informative - they give information instead of asking for credit card numbers ;-)), and I even got an email from "Facebook" that I requested a password change and that I have to 'click here' to change the password for [email address that isn't mine]. I am not the only addressee, there seems to be a whole list of Gmail addresses beginning with 'a'. The original addressee obviously has some sort of virus, and now I wonder if this could be a risk for me too. Is my email being sent around without my knowing too? I am not the kind of person who randomly clicks on shady links - I am very careful on the internet - but maybe there are other ways of catching viruses? Is there something I should do/check? Thank you for your help!

  Read the article

• Copying compressed files from Server 2008 R2 network share to XP client via VPN fails

  - by Dejan Janjuševic

  At the first sight the question looks similar to this one. I have experienced an odd behavior while trying to copy a certain file from Windows Server 2008 R2 network share to Windows XP Professional client via VPN. The VPN was set up using RRAS on the server machine. I will try to provide as much informations as possible in order to make the issue more clear. When trying to copy the compressed file sized ~2.5 MB (via Explorer or CMD, doesn't matter), the process stalls after some 20%, producing an error message after few seconds: Cannot copy filename: The specified network name is no longer available. If i start the command ping -t 192.168.2.1 (where the IP address specified belongs to the server) side by side with the copy command, I can clearly see that the ping command times out for few seconds as the copy process stalls. When this happens all network activities are frozen. After a few seconds, the network recovers, ping continues to run normally, however the copy process stands still before it displays the above error message. Copying other files (I tried 4-5 files), of which some are larger and some are smaller, succeeds. Seems to me that I can copy all uncompressed files. As soon as I try to copy an archive, the process freezes. Even a 707 KB large archive can't be copied. I can only reproduce this behavior on 2 machines, both Windows XP Professional, one is w/ SP2 and the other w/ SP3. Other XP clients don't have this problem, neither do Windows 7 clients. If I connect to the server using Remote Desktop Connection without using VPN from either of these 2 machines (using the same user account), I can copy anything I want normally, even these "problematic" files. Does anyone have any clue about what could possibly be going on?

  Read the article

< Previous Page | 487 488 489 490 491 492 493 494 495 496 497 498  | Next Page >