Search Results

Search found 15055 results on 603 pages for 'volume shadow copy'.

Page 491/603 | < Previous Page | 487 488 489 490 491 492 493 494 495 496 497 498  | Next Page >

• Computer not finding hard drives on boot -sometimes-

  - by todd.pund

  Computer specs: Mobo: Gigabyte ultradurable 3 - GA-970A-UD3 Processor: First gen I7 3.2GHZ Ram: 8GB Kingston DDR3 1066 Video Card: EVGA NVidia GTX 460 1GB Hard Drive: 500MB 7200rpm x2 (can't remember brand, sorry I'm at work.) Last week my developer preview for Windows 8 ran out so I put my copy of windows 7 back on the computer. The computer at that point started suffering from frequent freezing and crashing. When I rebooted the computer sometimes it wouldn't find the system HD at all. When I looked at the post screen it seemed to show that it wasn't finding either of the HDs. Then yesterday when turning on the computer I just got GRUB as a message (not a GRUB prompt, just GRUB) I haven't had a dual boot of Linux for at least a year. I loaded windows 7 recovery console from the disk and ran: bootrec /fixboot bootrec /fixmbr Which did not help. At that point I just installed Ubuntu 13.04 over the windows 7 install and still received the GRUB post. I went into the BIOS and switched the Hard Drive priorities and then it loaded into Ubuntu fine. For several days everything was just hunky dory until I installed the Ubuntu version of Steam, install Portal and tried to run it. At that point the computer froze and after hard rebooting couldn't find the hard disks again. Then after restarting the system it loaded up fine again and no issues since. (I have not tried to launch portal again). My next thought is to remove the system hard drive and try to use the secondary as the master to see if the primary HD is bad. I'm sorry if this has been confusing, I'll answer any questions I can. Any thoughts?

  Read the article

• Strange problem with Google Mail and IMAP on Outlook 2007

  - by Alex C.

  I work for a small non-profit organization. We have about 35 administrative employees who use e-mail. We're on a Windows network with a domain. Everyone is running XP Pro and Office 2007 with all updates/patches. We used to use POP3 mail through a local provider. However, we recently signed-up for a free Google Apps account, and we switched to IMAP mail through Google. Everyone uses Outlook 2007 as the client. For about ten days, everything was working fine. Yesterday afternoon, we suddenly developed a strange and annoying problem. Every time you send an e-mail message, a copy of your outgoing message shows up in your inbox. It's as if you're adding your own address to the CC: line of every message. Nothing has changed on our end. I was hoping that the problem was a temporary glitch that would resolve itself, but here we are about 24 hours later, and it's still happening. I searched Twitter, and there were a handful of vague messages about issues with Google mail and IMAP, but I didn't see any references to this specific problem. Any thoughts on what's going on here and how to fix it?

  Read the article

• Does migrating 2 domain controllers between 2 datacentre requires both virtual machines to be shut down at the same time?

  - by Imagineer

  I was attempting to migrate 2 virtual machines that are domain controllers between 2 datacentres running ESX 3.5 and ESX 4.1. I was advised to shut down both domain controller at the same time during the migration process. This is to avoid USN Rollback and other replication issues. The following are the steps that I was planning to perform: 1. Shutdown both DC. 2. Copy both VMs files across to new datacentre using Veeam FastSCP (connection to both vCentre through IP address instead of hostname) 3. Power them up at new datacentre. 4. Configure Network interface/DNS/DHCP for both DCs in new datacentre I have tried to use Veeam FastSCP rather than VMware Standalone Converter is because its copying rather than converting. Someone also suggested that I use backup and restore app like Veeam backup and replication software. Sounds like a simple job, but after shutting down both DCs, the transfer rate using FastSCP is so slow registering only 1KB/s as oppose to the normal 1MB/s (or more). When that attempt to transfer failed, I tried to cold clone both DCs resulted in the both ESX hosts get disconnected. I have tried troubleshooting by referring to this - VMware KB - Diagnosing an ESX Server that is Disconnected or Not Responding in VirtualCenter It seems that the DNS being down is the caused of all unusual occurrence. The moment I powered up the DCs via VMware console command, the ESX host were able to connect to the vCentre again. How can I avoid such a pitfall again? Am I doing it correctly? Any help would be greatly appreciated! Thank you.

  Read the article

• Running batch file through a service.

  - by wallz

  I'm trying to schedule a batch file to run through a third party application, however the output file doesn't get created in the directory. If I run the .BAT file from the command line, it works and the file gets created. Also using the Windows Schedule will also succeed. Basically, the 3rd party software will schedule the .BAT file and it shows success within the 3rd party user interface. The difference between running from the command prompt and the software, is that the software will use its Windows service to launch the batch. The 3rd party software will show success since it was able to successfully call the .BAT file to run, however it has no control of the other EXE's that's being called within the script. I'm able to run a simple .BAT file in the 3rd party software, for example a copy command. The .BAT I'm having problems with calls a compiled EXE which launches Excel to create a file to a location. The .bat file calls something.exe, which then calls Excel.exe: C:\something.exe -o D:\filename.xlsm C:\filename.xlsm refresh_pivot Do you think it's a permissions issue? I used Process Monitor to verify any Access Denied errors but everything seems to be working according to the trace. It worked on a non-64-bit OS, I'm currently using Win2008 64-bit.

  Read the article

• Using Windows Explorer, how to find file names starting with a dot (period), in 7 or Vista?

  - by Chris W. Rea

  I've got a MacBook laptop in the house, and when Mac OS X copies files over the network, it often brings along hidden "dot-files" with it. For instance, if I copy "SomeUtility.zip", there will also be copied a hidden ".SomeUtility.zip" file. I consider these OS X dot-files as useless turds of data as far as the rest of my network is concerned, and don't want to leave them on my Windows file server. Let's assume these dot-files will continue to happen. i.e. Think of the issue of getting OS X to stop creating those files, in the first place, to be another question altogether. Rather: How can I use Windows Explorer to find files that begin with a dot / period? I'd like to periodically search my file server and blow them away. I tried searching for files matching ".*" but that yielded – and not unexpectedly – all files and folders. Is there a way to enter more specific search criteria when searching in Windows Explorer? I'm referring to the search box that appears in the upper-right corner of an Explorer window. Please tell me there is a way to escape my query to do what I want? (Failing that, I know I can map a drive letter and drop into a cygwin prompt and use the UNIX 'find' command, but I'd prefer a shiny easy way.)

  Read the article

• Master does not appear to be a git repository error

  - by EmmyS

  I've inherited a position and instructions for creating a new git repository. Unfortunately I've run into problems and no one here knows what to do. Hoping someone can help me out. Here are the instructions I was left: Create a new repository: For these steps you need to be in the gitosis-admin repository, if you don't have it, in a suitable parent folder do: git clone [email protected]:gitosis-admin.git Edit gitosis.conf file - in gitosis-admin root, under [group base-repo] section, add the name of the new repo to the end of the "writable =" section. Commit change and push back to gitosis-admin master. For the next commands, my_new_project represents the name of your project mkdir my_new_project cd my_new_project git init Copy in any files you want to use to start the repo git commit -a -m "Initializing new repository" git remote add origin [email protected]:my_new_project.git git push master git push master:qa So I did 1 and 2, with no problem. It created a local folder on my machine called gitosis-admin. I edited the gitosis.conf file as indicated. But when I try to do step 3 (which I assume is git push gitosis-admin master) bash tells me that fatal: 'master' does not appear to be a git repository fatal: The remote end hung up unexpectedly What am I doing wrong?

  Read the article

• How to migrate Outlook Express mail rules?

  - by ronwest

  I have a home computer that only had a 15Gb C: drive, and ran out of space with all the Microsoft Updates, etc, that keep coming down. So I fitted a 160Gb drive as a C: drive and altered the drive jumpers to make the old C: drive into a slave D: drive, to save migrating documents, etc. I've installed a clean copy of Windows XP SP3 and reassigned the new Outlook Express' mailstore path to point to the old mailstore folder that now has a D: drive letter - and it all works OK. However, my extensive list of mail rules have not been transferred to the new OE and I have not been able to identify how they are stored. To find it I added a new rule to the new OE, exited OE, then searched on the whole computer (including hidden/system files) for files altered around the time I added the rule. I hoped I could just overwrite a new empty file with an old one. But the only files that seem to be changed are Windows system-level files and some bits and pieces in the Windows\PreFetch sub-folder. None of them can be opened as XP has them locked, and none of them have names that are anything to do with email or rules. Does anyone know of any way of migrating OE rules, or do I have to re-enter them by hand? Thanks!

  Read the article

• Some of my keys are automatically being pressed along with other keys

  - by Santosh

  History The last time when my computer shutdown was a power failure. Now some keys are automatically being pressed when I type something. The last thing I did to keyboard setting was adding a keyboard layout (on Ubuntu). What is happening Whenever I press c, xc is writeen s gives me sd d gives me sd e gives me we 2 gives me 23, So when I want @ it gives me @# 3 gives me 23 Pressing CAPS Lock gives me F3 and vice-versa. All other key are either working fine or I don't use them. I have two operating system Ubuntu and Windows, I use Windows very less and found this problem on Ubuntu, but as soon as I logged in to Windows (for checking) then I found that Windows has the same problem. Effects on my life This starts form the time of login, even I have problem in typing my password. Whenever I try to save any webpage, it is bookmarked automatically. Whenever I copy, it is cut automatically. I have to spend more than half of time correcting what I have typed. Note: Typing thisd quwesdtion wasd rweally a big pain to mwe.

  Read the article

• Restoring a fresh home folder in a shared user domain environment

  - by Cocoabean

  I am using a tool called pGINA that adds another credential provider to my Windows 7 clients so we can authenticate campus users via campus LDAP. We have the default Windows credential providers setup to authenticate off of our Active Directory, but we have students in our classes that don't have entries in our AD, and we need to know who they are to allow them internet access. Once these LDAP users login using pGINA, they are all redirected to the same AD account, a 'kiosk' account with GPOs in place to prevent anything malicious. My concern is that my users will accidentally save personal login information or files in that shared profile, and another user may login later and have access to a previous user's Gmail account, as the AppData folder on each computer is shared by anyone logging into the kiosk user. I've looked into MS's 'roll-your-own' SteadyState but it didn't seem to have what I wanted. I tried to write a PS script to copy a pre-saved clean version of the profile from a network share, but I just kept running into issues with CredSSP delegation and accessing the share from the UNC path. Others have recommended something like DeepFreeze but I'd like to do it without 3rd party tools if possible.

  Read the article

• Common folder in linux

  - by rks171

  I have two users on my Ubuntu machine. I want to share some media files between these users, so I created a directory in /home/ called 'media'. I made the group 'media' and I added my user 'rks171' to the group 'media'. So: sudo groupadd media sudo mkdir -p /home/media sudo chown -R root.media /home/media sudo chmod g+s /home/media As was described in this post. Then, I added my user to the group: sudo usermod -a -G media rks171 Then I also added write permission to this folder for my group: sudo chmod -R g+w media So now, doing 'ls -lh' gives: drwxrwsr-x 2 root media 4.0K Oct 6 09:46 media I tried to copy pictures to this new directory from my user directory: mv /home/rks171/Pictures/* /home/media/ And I get 'permission denied'. I can't understand what's wrong. If I simply type, 'id', it doesn't show that my user, rks171, is part of the 'media' group. But if I type, 'id rks171', then it does show that my user, rks171, is part of the 'media' group. Anybody have any ideas why I can't get an files into this common folder?

  Read the article

• Having trouble with a workaround, for booting from a usb stick, using grub and a minimal linux kernel to load usb drivers

  - by s hanley

  I'm trying to boot from a usb stick. I formatted it to fat32, and later to ext2, and installed dsl on it using unetbootin, and later the usb install guide on dsl wiki (http://www.damnsmalllinux.org/wiki/index.php/Install_to_USB_From_within_Linux). The bios doesn't have a setting for booting from usb. Grub doesn't "see" the usb drive when I use the root and find commands, explained in (http://www.damnsmalllinux.org/wiki/index.php/USB_Booting). This happens even when I set boot from floppy at the top of the boot order. However, my usb keyboard is recognised by the bios and by grub. How can it recognise the keyboard but not the usb drive? Also, the usb led does flash even before grub starts up, so surely something must be happening usb-wise? I am now following an ubuntu guide to booting from a USB stick, using a hdd-based, minimal linux kernel to supply the usb drivers. But I'm having difficulty adapting it to other OSes (slax/dsl/aptosid). I believe I have to alter the initrd.gz file to include usb drivers and then copy that file along with vmlinuz to a partition on my hdd. But, what's the grub command for the kernel line supposed to look like? From the ubuntu example it's: title USB FLASH DRIVE root (hd0,6) kernel /boot/usb-boot/vmlinuz file=/cdrom/preseed/ubuntu.seed boot=casper noprompt cdrom-detect/try-usb=true persistent initrd /boot/usb-boot/initrd.lz boot Should mine just be: title USB FLASH DRIVE root (hd0,6) kernel /boot/usb-boot/vmlinuz cdrom-detect/try-usb=true initrd /boot/usb-boot/initrd.lz boot

  Read the article

• How long will a "safely stored" Solid-State-Drive (SSD) keep its data? (e.g. bank safety-deposit box)

  - by user31575

  Here's my usecase: once-and-only-once copy off photos/videos to an internal SATA Solid State Drive (SSD) put this drive in a well-ventilated, air-conditioned bank "safety deposit box" for safe keeping The question: How long can I safely store a solid-state-drive in such an environment? i.e. 0% bitrot, 100% success when "plugged in" Are some SSD drives more reliable than other for this usecase? (e.g. smaller size vs larger size, SLC vs MLC, different brands, etc) More fodder: I have read that solid state memory cards (e..g compactflash, or sd cards) have much longer durability than other media (DVD's, CD's, hard drives) for this usecase (guaranteed against bitrot/other dysfunction on the order of ~ a decades vs a year ). I don't know if this applies to "SSD hard drives". Copying to one 500Gb ssd vs 8 64gb flash drives is easier SSD SATA hard drives have no moving parts, but they have more "visible electronics" than a compact flash card. I don't know if this "visible electronics" can fail, i.e. in contr I know many will point to carbonite, other cloud backup stuff, but I like the simplicity of having physical copies and wanted to understand the risks/implications thanks,

  Read the article

• Can a USB/IDE/SATA adapter be flaky?

  - by Ward

  I use USB/IDE/SATA converters a lot and on the two that I have now, I sometimes get errors copying files to drives. It only happens when I'm copying big files to the drive (big can mean as little as 100MB, I think it happens more often with bigger files - 300MB or more), and basically the copy will fail and I'll get one or more error messages about "Delayed write failed." But if I disconnect the drive and re-connect it, I'll usually be able to continue. (The file that was being copied will be corrupt, but otherwise the drive is fine.) I just noticed a new type of flakiness: the data transfer rate can vary widely. I copied one set of files (5x300MB files) and it took 10+minutes, then I copied another set (approx. the same sizes) and it took less than a minute. I haven't done systematic testing, the other things I'm doing on my laptop at the same time might have some impact, and I haven't cross-checked the two adapters I have and the 3 hard drives I'm working with to see if there's a pattern. I'm more wondering if anyone else has seen anything like this.

  Read the article

• Shortcuts located in "D:\Program Data\..." not working even though they're pointing to the right targets (Windows 7)

  - by Kevin

  I just made a fresh install of my windows 7 home premium using my laptop's recovery disks (HP Pavilion dv6-2151cl) using minimal settings. After install, I set up "Program Data" and "Users" to my D partition to save space changing the folders in the registry. Then I updated windows (including W7 SP1), and installed all other programs. After installing all other programs I noticed that the icons of all new programs (not included in the windows install) in "All Programs" had a blank sheet as icon and they don't do anything. Looked into "D:\Program Data\Microsoft\Windows\Start Menu\Programs" in the windows explorer and the same is true there. All the shortcuts in C: and "D:\Users..." work both in the "Windows Explorer" and "All Programs". Also I noticed that the shortcuts do display the right icons inside the "open" dialog boxes. And if I copy the shortcuts in "D:\Program Data..." to the desktop they also work as expected. I checked file association for .lnk and it was OK, but also tried the registry fixers for this file association and they had no effect. There are no missing programs that I can tell in the "All Programs" menu, the just don't do anything if they lay in "D:\Program Data...". Any thoughts on how to make Windows 7 treat shortcuts in "D:\Program Data..." as they should?

  Read the article

• P2V Wouldn't Boot, Rebuilt initrd, Need to Clean Up

  - by Mike Soule

  We have a CentOS 5.4 server (build 2.6.18-164.el5xen). We went to P2V this server so we can have redundancy, the physical only has one PSU. The P2V only completed 99% of the way, we have a VMWare ticket opened, but they marked the ticket as low priority. I was able to boot into a rescue disc of Red Hat 5.4 and rebuild the initrd with the help of this blog post. Now the only issue is the original server had a modified initrd, which was also from a different OS build and made by an outside provider. We do not have a document outlining modifications. My question is, is it at all possible to copy the initrd off of the physical server and replace it on the virtual and some how have the virtual machine boot? Thanks for any input. Edit: I copied the initrd img from the physical and it recreated the original issue. Here is a screen capture of the error. http://i.imgur.com/MqC73.jpg Edit2: echo Scanning logical volumes lvm vgscan --ignorelockingfailure echo Activating logical volumes lvm vgchange -ay --ignorelockingfailure VolGroup00 resume /dev/VolGroup00/LogVol01 echo Creating root device. mkrootdev -t ext3 -o defaults,ro /dev/VolGroup00/LogVol00 echo Mounting root filesystem. mount /sysroot

  Read the article

• Microsoft Deployment Toolkit 2012 Error

  - by Jacob Schaer

  I just started with MDT2012 recently in hopes of eventually getting away with using Ghost to deploy all of our department computers. When I test deploy in VirtualBox, it deploys the OS properly, but stops because of a network driver failure (it gets the "could not allocate resources" issue). On physical hardware (Latitude E6500, Optiplex 980, and an older Latitude) it gets through the multicast and stops immediately after with: "Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information" I've looked at the logs and never see anything really of note. Originally I was using DriverPacks from DriverPacks.net, but thinking it was a driver issue, I switched over to using Dell's cab driver packs. Still the same issue. I check and it did the HDD is all fine - it was properly partitioned, set to bootable, and was loaded with all the proper OS installer files. I'm using a flash drive to do the install - when I make changes to the deployment share I rebuild and copy the ISO to the drive, then use YUMI multiboot to start the ISO (probably irrelevant).

  Read the article

• Backup Picasa 'people' tags data

  - by pelms

  OK, so I've spent a fair amount of time putting names to faces in Picasa 3.5 but in a few days (hopefully) my copy of Windows 7 should arrive and I'll need to reinstall Windows. So, does anyone know what I need to backup so that I don't have to re-enter all those name tags? N.B. I'm on Windows 7 RC and know that I don't have to do a clean reinstall but I would prefer to. Outcome: I clean installed Windows 7 and downloaded and installed Picasa. Unfortunately, the download link on the UK Picasa homepage still pointed to Picasa 3.0 (rather than 3.5) which doesn't have face recognition. This scanned my photos folders and overwrote the picasa.ini files along with the people information   :¬( Fortunately I'd backed up the photos before installing Win 7, so after uninstalling Picasa 3.0 (along with it's database), restoring the photos from backup and installing Picasa 3.5, I finally got my face names back. Extra... Google has now posted advice on how to migrate to Windows 7 and keep your Picasa database, meaning that it will not need to rescan you photos and will retain all information about then including name tags. They have a method for upgrading and for a clean install of Win 7. Basically you need to back up: "C:\Users\%username%\AppData\Local\Google\Picasa2" and "C:\Users\%username%\AppData\Local\Google\Picasa2Albums"

  Read the article

• Windows mounted network drives slow after upgrading switch

  - by Kver

  On our small business network our old 10/100 consumer grade switch gave up the ghost, and we replaced it with a proper business-grade gigabyte switch. After wiring it in our Linux and Mac users immediately got back to working off of network drives; But 2 of our 3 Windows 7 PCs have suddenly experienced a tremendous slowdown with mapped network drives; Windows will become stuck "discovering" a folder causing applications to freeze when trying to open files. It will instantly display and browse files, but the moment you try to open one the bug hits. To remedy this we have our users copying files to the desktop, but it can take a few minutes while windows is stuck "calculating" the time it will take to copy. These aren't big files, mostly excel sheets less than 500KB - these operations are instant on Linux and Mac. (The third Windows machine is having no issues) I've tried remapping the drives, mapping to different drive letters, rebooting, etc. I'm at a loss, because switches are mostly transparent, and it's only after the switch was replaced that the Windows PCs started acting up. What black-magic voodoo am I missing to make Windows work? Thank you.

  Read the article

• Moving a lot of small files between servers using rsync

  - by Adirael

  Hello guys, I'm moving a lot of files (about 2 millions) between two servers on different locations using rsync over ssh, it seems to work fine but I just realised I'm losing some files on the process. I got server 1, with the original data, and server 2, with the copy. Server 1 runs CentOS 5 and Server 2 runs on Ubuntu 10. I'm doing the transfer on the Server's 2 command line like this: rsync -e ssh -avzn usr@server1:/remote/path /local/path The first file movement I did using tar, but I didn't though of piping it through ssh and it failed cause the disk on server 1 was almost full, so I transfered it anyways (it was about 200GB) and got about 80% of the files. Then I piped another tar with the rest of the files (they're in folders, I got 100 folders with about 30 subfolders each, with files inside) and now I got everything on server 2. I wanted to be sure, so I my two options are getting the md5sum of all the files and check them or running an rsync on server 2 against server 1, that's what I did. It got some missing stuff and now it says there's nothing more to do (DRY RUN). But I got at least two files that are missing inside a subfolder. I ran that same rsync on that folder, but still dry run. Am I doing something wrong? Thanks, and sorry for the wall of text.

  Read the article

• Server 2008 RAID 5 Write Speeds

  - by Solipsism

  I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

  Read the article

• Configure New Server for .htaccess

  - by Phil T

  I have a new LAMP CENTOS 5 server I am setting up and trying to copy the configuration from another web server I have. I am stuck with what I think is a mod_rewrite problem. If I go to http://old-server.com/any_page_name.php it correctly routes through some handling code in index.php and shows me a graceful "Page Cannot Be Displayed" message. But if I go to http://new-server.com/any_page_name.php I get an ugly Apache 404 Not Found error message. I looked in both httpd.conf files and they both have only one reference to mod_rewrite. LoadModule rewrite_module modules/mod_rewrite.so So it seems like that should be fine. At the bottom of httpd.conf I have the code: <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /var/www/html ServerName new-server.com ErrorLog logs/new-server.com-error_log CustomLog logs/new-server.com-access_log common </VirtualHost> Then in the root of /var/www/html I have the exact same .htaccess file that looks like this: RewriteEngine on Options +FollowSymlinks RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . index.php [L] ErrorDocument 404 /page-unavailable/ <files ~ "\.tpl$"> order deny,allow allow from none deny from all </files> So I don't see why the page load at old-server.com works fine while new-server.com doesn't route through index.php like I want it to do. Thanks.

  Read the article

• How could I embed formatted XML source in WORD documents?

  - by eckes

  I'm writing a documentation with WORD that contains XML source code (whole files) as examples. The way I'm embedding the currently XML is quite cumbersome and doesn't seem to me as really maintainable: I'm finishing the editing of the document in WORD and create a PDF from it using Acrobat next, I open my XML files (2x input files, 2x generated output files) with IE and print them with the PDF printer supplied by Acrobat now, I open up Acrobat Pro and attach the four XML-PDF files to my original document The problem with that work flow for me is that it involves too much manual labor in order to get the documentation done. What I've tried up to now is not really satisfying for me: converting each XML to PDF and appending them like described above opening the XML files with SCiTE, copy as RTF and paste into Word playing around with the LaTeX packages minted, pygments and listings (I could write the docs with LaTeX too) but found some unsolvable problems in each of these packages I'm searching for a way that produces my documentation more automatic. For example embedding the XML files including formatting of IE (which I find quite readable). The files should be included by reference so that I don't have to paste the XML sources manually every time the XML changes.

  Read the article

• How do I cancel windows server 2003 repair install?

  - by Kilgore2k

  System: Windows 2003 Server Enterprise Scenario: NTDS db is corrupt and all attempts to fix with esentutl fail. Ran chkdsk which seemed to repair disk error and give access to the ntds.dit file but still esentutl fails. (Attached the drive to a different server to run the esentutl) Error: Access to source database '[path to copy of]/ntds.dit' failed with Jet error -1022. Operation terminated with error -1022 (JET_errDiskIO, Disk IO error) after 0.170 seconds. This error occurs on any disk I cpoy the files to including original location in C:\WINDOWS\NTDS\ Now enter the "Stupid!" and "what was I thinking!?" part (must be the late hour...) Stupid: No updated backup - after using a backup I get a network password error in the lsass error. what was I thinking!?: Started the install repair from the original CD but the install fails since the AD fails to start. Now I cant boot into any mode (safe mode, AD restore etc) nor complete the repair install. I would really like to avoid a fresh install since I have the Exchange server on this DC and would rather migrate to a new server than have to start from scratch. Thanks!

  Read the article

• How should I configure backup of my server?

  - by ed209

  I have just rented a dedicated server. If it helps this is the config I have: CPU1 Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz (Cores 8) RAM 15975 MB Disk /dev/sda doesn't contain a valid partition table (=> /dev/sda doesn't) Disk /dev/sdc doesn't contain a valid partition table (=> /dev/sdc doesn't) Disk /dev/sdb doesn't contain a valid partition table (=> /dev/sdb doesn't) Disk /dev/sda: 120.0 GB (=> 114 GIB) Disk /dev/sdc: 3000.6 GB (=> 2861 GIB) Disk /dev/sdb: 3000.6 GB (=> 2861 GIB) /dev/sda is a 120GB SSD. This is where I have Ubuntu/lamp installed. It's the drive that will run my site. With the account I got two other drives of 3000GB each which I really don't need but they came with the account. I figured I could use these to back up my main 120gb drive. So a couple of things I wondered were: Should I use these for backups? How should I back up. The data I want to back up is a user uploads directory full of images and the database. Everything else is either in a code repo or backed up some other way. For example, it would be nice to know there is a disk image of the 120gb drive somewhere that I can copy over should there be any problems but equally I don't mind doing a fresh install of all the software and copying over just the images and database dump. Thanks for your advice! (also, happy to not use the two other drives and backup elsewhere if it's more sensible)

  Read the article

• Would a PHP application benefit from being served from a RAM drive?

  - by Tom Marthenal

  I am in charge of hosting a PHP application that is large and slow, but easy to scale. The application is entirely static, with writable disk storage needed. We've profiled the application, and the main bottleneck appears to come from loading the application and not the work the application does. The application is not CPU-intensive, although it does use a fair amount of memory (think Magento). Currently we distribute it by having a series of servers with the same PHP files on their hard drive and a load balancer in front of them. Easy but expensive. I've been reading about RAM disks and the IO benefits they offer, and was wondering if they would be well-suited to PHP applications. Since PHP applications are loaded from disk for every request and often involve lots of different files (as opposed to being kept in memory like with a Java application), I would figure that disk performance can be a severe bottleneck. Would placing the PHP files on a RAM disk and using the mount point as Apache's document root offer performance benefits? A startup script could create the RAM drive and then copy the files (which are plain-text and small) from a permanent location to the temporary RAM drive. Does this make sense, or should I just trust the linux kernel to cache the appropriate files in memory by itself?

  Read the article

< Previous Page | 487 488 489 490 491 492 493 494 495 496 497 498  | Next Page >