Search Results

Search found 17945 results on 718 pages for 'last fm'.

Page 494/718 | < Previous Page | 490 491 492 493 494 495 496 497 498 499 500 501  | Next Page >

• My internet drops and will only reconnect if I troubleshoot it or restart my computer.

  - by Paul

  My internet loses its connection and at the same time, and my speaker seems broken if that happens and my mouse will not be smooth as it was before it happens. It already happened before and I didnt mind it. But now, it's happening literally all the time. After startup, my connection seems okay but after some few minutes, even without me doing something, my laptop will just lose its connection. It says that it is not connected and connections are available, but if I check if there are connections where I can connect it shows nothing. Even if, there is actually a wi-fi connection where my phone and other laptops connect. They dont seem to have problem with it. Just my laptop. After that happens, I usually restart my laptop but I discovered that troubleshooting it would somehow repair the problem, but not all the time. It says that restarting my wireless adapter do the job. Are there any long term fix? I mean that could last long or totally erase the problem? I have Atheros AR5B97 Wireless Network Adapter and Microsoft Virtual WiFi Miniport Adapter, both enabled. On the services, I have Wired AutoConfig and WLAN AutoConfig on Automatic. Aspire 4750, Windows 7 (x86)

  Read the article

• PC freezes after repeated clicking noises

  - by Péter Török

  I have an oldish PC (Athlon XP 2200, WinXP). Every time I switch it on, I hear a loud "click" first of all, and when it is shut down, again a click is the last sound I hear. Lately it started to behave erratically: it started to click loudly in the middle of a session. First only once in a while, then repeatedly for several seconds in a row, and finally it froze completely. We were not doing anything particular during these times, usually just browsing the web. This has already happened twice in a few week's time period. We typically use it only in the evenings, so when the freeze happened, I just decided it is time for the bed. When it was started up the next day, everything looked fine. Any hints on what could be the culprit? Could it be caused by an ageing heat fan, or dust that has accumulated inside the case? We are backing up all the data stored on it, and then will open the case to look inside, but I thought it would be good to get some background info first of all.

  Read the article

• Offline cache copies in Windows file sharing

  - by netvope

  I frequently access media files (music or video) on a remote Windows file share. My Internet connection is not very fast, and I find it a waste of bandwidth when I repeatedly access the same files. For example, I may listen to the same song 30 times in a month. So, I would like to cache files I've used. I know Windows has an "Always available offline" feature but I dont' think it suit my needs. I don't want to make the whole share "available offline" as the remote Windows file share is huge (in terabytes). Making individual files "available offline" is tedious as the files are scattered in many different directories. It would be much more convenient if the system can simply cache those I've used. I could also manually make a local copy each time I use a file... but this is even more troublesome than making each file "available offline" Also The files on the share seldom change. Many of the files are rarely used. Some of the files are frequently used. I don't have a list of the most frequently used files. It would be the best if I could tell Windows to cache the last accessed 10GB, but apparently it doesn't have this feature. So I think the best way is to have a SMB/CIFS caching proxy. What do you think? I have a Linux box sitting around. Perhaps I should try to setup samba4?

  Read the article

• Mac SMB connections to Windows 2003 server, leaving Open Files

  - by Bruce Garlock

  We have several Mac clients (Both 10.5, and 10.6) mounting a share from a Windows 2003 server. At least once a day, our archivist will go into this share to archive items from it, to the backup server. Most of the time, she has no issues: she copies the folder to the archive server, when it's done, she deletes it from this share. Then, she will come upon one, and it will say she doesn't have permission. When I go into the Open sessions, it will say that a particular user has a READ lock on the file, in Windows 2003. Of course, this person does not have the file open, and the only way we can delete it, is to close the open session on the file. My thoughts: The Mac likes to "sprinkle" Hidden "Resource Forks" on SMB servers, and possibly, when this Mac who last wrote to that share, closes out of the file, and these files still exist. Windows 2003 has a bug, that doesn't properly "release" the OPLOCK on the file? Steve Ballmer just doesn't like Mac's, so he wants to annoy everyone by not releasing file locks :-) What can be done about this? It happens every day, and sometimes several times per day! Many thanks, Bruce

  Read the article

• MAMP Pro .xip.io, fixing urls with htaccess

  - by user3540018

  I've got all my websites set up with MAMP Pro. For instance, I got it set up, so when I go to example.com, the browser displays the website that's set up on my iMac. Now, I wanna get MAMP Pro to work so I can view my website on my other computers/devices (which are all hooked up on the same network.) So far all I had to do is check the checkbox "via Xip.io (LAN only)", and now I can view my website on my other computers/devices within my LAN by simply going to example.com.10.0.1.13.xip.io. Problem is, whenever I'm on this other computer/device, when I click on the links, I get 404 error. ie. whenever I go to example.com/news, I get the 404. But when I go to example.com.10.0.1.13.xip.io/news, THEN I get the right page. So in order to solve my problem I need to rewrite the urls. So whenever someone clicks on a link ie. goes straight to example.com/news, he'll go to example.com.10.0.1.13.xip.io/news. I don't want to change all the links in my MySQL file, but I believe I can do it simply with the htaccess file. I've opened the htaccess file and added the last two lines, but it just doesn't work. <IfModule mod_rewrite.c> RewriteEngine On # Send would-be 404 requests to Craft RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_URI} !^/(favicon\.ico|apple-touch-icon.*\.png)$ [NC] RewriteRule (.+) index.php?p=$1 [QSA,L] RewriteCond %{HTTP_HOST} ^example\.com RewriteRule ^(.*)$ http://www.example.com.10.0.1.13.xip.io/$1 [R=permanent,L] </IfModule> Or perhaps I don't need to change the htaccess file, is there something that I could be missing in the MAMP Pro settings, or perhaps a MAMP extension that I need?

  Read the article

• Compress a folder of PDF files into separate zip archives

  - by Panrubius

  I wanted to take a folder full of PDF files and create a number of separate zip files, after following the advice on this question everything worked *almost*perfectly. Here's what happened: When I issued this command in Terminal: zip -s 5m -r ~/Desktop/invoices ~/Desktop/Invoices/ Everything worked really well, in that I got 11 ZIP files of approximately 5 MB each; placed in the folder specified. However, the files they outputted were named as follows: invoices.z01 invoices.z02 invoices.z03 invoices.z04 invoices.z05 invoices.z06 invoices.z07 invoices.z08 invoices.z09 invoices.z10 invoices.zip So as you can see only invoices.zip has been named correctly. I could go through and rename them one by one, but seriously, if we start doing that then what in the name of Evolution are computers for?! Now, I am also aware that I'm relatively new to the Terminal; so I could be making a very silly mistake somewhere. If that's the case, please be patient :-) Any help would be greatly appreciated. One last note: I'm quadriplegic so I would like to avoid GUI applications as much as possible, I use voice recognition software you see this working in the Terminal is much much easier.

  Read the article

• Tripwire help Required

  - by ramaperumal

  I have created the policy file in Tripwire and also I have created the rules as well mentioned below: /opt/jboss/server/gis/conf -> $(SEC_CONFIG) +aipm +c+g+a+i+s+t+u+l+M; /usr/local/gtech/eseries/ -> $(SEC_CONFIG) +a+c+g+i+s+t+u+l+M ; After running the integrity check the output should be a(Access timestamp),c (Inode timestamp (create/modify),g (File owner's group ID),i (Inode number),s (File size),t (time stamp),u (File owner's user ID),l(File is increasing in size (a "growing file"),M (MD5 hash value). I am getting the output as below: [root@xxsi1242 tripwire]# tripwire --check Parsing policy file: /etc/tripwire/tw.pol *** Processing Unix File System *** Performing integrity check... Wrote report file: /var/lib/tripwire/report/xxsi1242.gtk.gtech.com-20131106-053812.twr Open Source Tripwire(R) 2.4.1 Integrity Check Report Report generated by: root Report created on: Wed 06 Nov 2013 05:38:12 AM EST Database last updated on: Wed 06 Nov 2013 05:31:17 AM EST =============================================================================== Report Summary: =============================================================================== Host name: xxsi1242.gtk.gtech.com Host IP address: 156.24.65.171 Host ID: None Policy file used: /etc/tripwire/tw.pol Configuration file used: /etc/tripwire/tw.cfg Database file used: /var/lib/tripwire/xxsi1242.gtk.gtech.com.twd Command line used: tripwire --check =============================================================================== Rule Summary: =============================================================================== ------------------------------------------------------------------------------- Section: Unix File System ------------------------------------------------------------------------------- Rule Name Severity Level Added Removed Modified --------- -------------- ----- ------- -------- Invariant Directories 66 0 0 0 Temporary directories 33 0 0 0 * Tripwire Data Files 100 0 0 1 Tech Stack 100 0 0 0 User binaries 66 0 0 0 Tripwire Binaries 100 0 0 0 * CLPS bins 100 0 0 2 CLPS Configuration files 100 0 0 0 ESCommon 100 0 0 0 Shell Binaries 100 0 0 0 OS executables and libraries 100 0 0 0 Security Control 100 0 0 0 ESCommon Configuration 100 0 0 0 (/etc/gtech/escommon) Total objects scanned: 12358 Total violations found: 3 =============================================================================== Object Summary: =============================================================================== ------------------------------------------------------------------------------- # Section: Unix File System ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- Rule Name: Tripwire Data Files (/etc/tripwire/tw.pol) Severity Level: 100 ------------------------------------------------------------------------------- Modified: "/etc/tripwire/tw.pol" ------------------------------------------------------------------------------- Rule Name: CLPS bins (/opt/jboss/server) Severity Level: 100 ------------------------------------------------------------------------------- Modified: "/opt/jboss/server/esapps1/data/hypersonic/localDB.lck" "/opt/jboss/server/gis/data/hypersonic/localDB.lck" =============================================================================== Error Report: =============================================================================== No Errors ------------------------------------------------------------------------------- *** End of report *** Note: In the output I only am getting the files which are modified. I need the detail output for this. But unfortunately I am not getting what I expected. Please help me to proced further.

  Read the article

• NGINX rewrite for vanity URLs when file doesn't exist (try_files and rewrite together)

  - by user1721724

  I'm trying to get vanity URLs on my server. If the file path from the URL doesn't exist, I want to rewrite the URL to profile.php, but if my users have periods in their usernames, their vanity URL doesn't work. Here is my conf block. server { listen 80; server_name www.example.com; rewrite ^/([a-zA-Z0-9-_]+)$ /profile.php?url=$1 last; root /var/www/html/example.com; error_page 404 = /404.php; location ~* \.(js|css|png|jpg|jpeg|gif|ico)$ { expires 1y; log_not_found off; } location ~ \.php$ { fastcgi_pass example_fast_cgi; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www/html/example.com$fastcgi_script_name; include fastcgi_params; } location / { index index.php index.html index.htm; } location ~ /\.ht { deny all; } location /404.php { internal; return 404; } } Any help would be appreciated. Thanks!

  Read the article

• Connect Chrome to TOR

  - by Jack M

  I'm having difficulty connecting Chrome to TOR. I started trying yesterday. I started Vidalia and the TOR Browser and then followed the advice at http://lifehacker.com/5614732/create-a-tor-button-in-chrome-for-on+demand-anonymous-browsing - downloading Proxy Switchy and setting it up as stated. This resulted in Error 130 (net::ERR_PROXY_CONNECTION_FAILED) (in Chrome, when I tried to load a webpage). So I looked into Vidalia's settings and noticed that it appeared to be using port 9051, so I set that instead of 8118 as everyone on the internet seems to be suggesting. Then I got a new error: Error 111 (net::ERR_TUNNEL_CONNECTION_FAILED). Digging a bit, I found that Tor should be set as a SOCKS proxy, not an HTTP proxy, so I unticked "use same settings for all protocols" in Proxy Switchy and just set localhost:9051 for SOCKS. That got me Error 7 (net::ERR_TIMED_OUT). And that's when I came here for help. I typed up the above question, but then at the last minute decided to do a bit more reading and found someone here suggested using some command line arguments via a Windows shortcut: "C:\snip\chrome.exe" --proxy-server=";socks=127.0.0.1:9051;sock4=127.0.0.1:9051;sock5=127.0.0.1:9051" --incognito check.torproject.org And that worked perfectly. Yesterday. Today it doesn't, so I'm having to post this question after all. check.torproject.org gives me a "no" with Chrome, but a "yes" with the default Tor Browser. I tried closing Chrome and restarting it (yes, with the correct shortcut) after Vidalia started, but still nothing. The port number hasn't changed or anything. What gives? EDIT: I realized I had a "non tor" instance of Chrome running and that possibly the was causing the command line args t be ignored when I started the new instance. Closed all instances of chrome and ran my Chrome Tor shortcut, and it did get rid of the "not using Tor" message -- because I got another Time Out error instead. Vidalia's bandwidth graph didn't even blink.

  Read the article

• Which is more secure: Tomcat standalone or Tomcat behind Apache?

  - by NoozNooz42

  This question is not about performance, nor about load-balancing, etc. Which would be more secure: running Tomcat in standalone mode or running Tomcat behind apache? The thing is, Tomcat is written in Java and hence it is pretty much immune to buffer overrun/overflow (unless a buffer overrun in a C-written lib used by Tomcat can be triggered, but they're rare [the last I remember was in zlib, many many moons ago] and one heck of a hack to actually exploit), which gets rid of a lot of potential exploits. This page: http://wiki.apache.org/tomcat/FAQ/Security has this to say: There have been no public cases of damage done to a company, organization, or individual due to a Tomcat security issue... there have been only theoretical vulnerabilities found. All of those were addressed even though there were no documented cases of actual exploitation of these vulnerabilities. This, combined with the fact that buffer overrun/overflow are pretty much non-existent in Java, makes me believe that Tomcat in standalone mode is pretty secure. In addition to that, I can install both Java and Tomcat on Linux without needing to be root. The only moment I need to be root is to set up a transparent port 8080 to port 80 forwarding (and 8443 to 443). Two iptables line as root, that's all root is needed for. (I don't know for Apache). Apache is much more used than Tomcat and definitely does not have a security track record as good as Tomcat. What would make Tomcat + Apache more secure? What would make Tomcat + Apache less secure? In short: which is more secure, Tomcat standalone or Tomcat with Apache? (remembering that performance aren't an issue here)

  Read the article

• Apache error "child pid XXXX exit signal exceeded file size limit (25)"

  - by Stephen Melrose

  Morning all, Apache on our internal development server stopped working last night. It's running, but all we get is a blank screen, no server errors. Examing the error log shows the following, [Fri Apr 23 09:13:57 2010] [notice] child pid XXXX exit signal exceeded file size limit (25) [Fri Apr 23 09:14:03 2010] [notice] child pid XXXX exit signal exceeded file size limit (25) [Fri Apr 23 09:14:03 2010] [notice] child pid XXXX exit signal exceeded file size limit (25) [Fri Apr 23 09:14:06 2010] [notice] child pid XXXX exit signal exceeded file size limit (25) After some Googling, we found that this is due to Apache trying to handle a file greater than it's maximum allowed limit, which by default is 2GB and is usually an error log. I did a search using find . -size +1000000k -ls (find all files greater than 1GB) in our log and web folders, but nothing showed up. I've also restarted Apache and rebooted the server itself serveral times. I've completely wiped the log folder and started a fresh. Nothing is working. Any ideas as to what else might be causing this? Thank you

  Read the article

• Tomcat Solr times out

  - by user568458

  (Plesk 10.4 centos 5.8 linux apache2 server, with Tomcat5 on port 8080 and Apache Solr) I get "The connection has timed out" on requesting domain.com:8080 or www.domain.com:8080 or ip.ad.dr.ess:8080 Every reason I can find why this might be seems not to be the case: Plesk thinks Tomcat is running fine and lists it as an active service. The firewall currently has an accept all rule on port 8080. There's nothing relevant in the catalina tomcat logs (/var/log/tomcat5) - just some stuff from last time tomcat was started. There's no record at all of the requests that fail. netstat -lnp | grep 8080 gives the following, which I beleive means Tomcat is listening to requests to port 8080 on all ip addresses from any ip and any port (please correct me if I'm wrong): : tcp 0 0 0.0.0.0:8080 0.0.0.0:* LISTEN 4018/java This covers every cause of this time out that I can find - so I must be missing something fundamental. It seems Tomcat is running, listening to the right port, is getting an appropriate IP address, is not obstructed by a firewall and is not failing after receiving a request in a way which would be recorded in the logs (so I believe it can't be out of memory, or anything like that). I'm all out of ideas on how to continue debugging this. I must have overlooked something obvious. Can anyone help?

  Read the article

• "Server Unavailable" and removed permissions on .NET sites after Windows Update

  - by tags2k

  Our company has five almost identical Windows 2003 servers with the same host, and all but one performed an automatic Windows Update last night without issue. The one that had problems, of course, was the one which hosts the majority of our sites. What the update appeared to do was cause the NETWORK user to stop having access to the .NET Framework 2.0 files, as the event log was complaining about not being able to open System.Web. This resulted in every .NET site on the server returning "Server Unavailable" as the App Domains failed to be initialise. I ran aspnet_regiis which didn't appear to fix the problem, so I ran FileMon which revealed that nobody but the Administrators group had access to any files in any of the website folders! After resetting the permissions, things appear to be fine. I was wondering if anyone had an idea of what could have caused this to go wrong? As I say, the four other servers updated without a problem. Are there any known issues involved with any of the following updates? My major suspect at the moment is the 3.5 update as all of the sites on the server are running in 3.5. Windows Server 2003 Update Rollup for ActiveX Killbits for Windows Server 2003 (KB960715) Windows Server 2003 Security Update for Internet Explorer 7 for Windows Server 2003 (KB960714) Windows Server 2003 Microsoft .NET Framework 3.5 Family Update (KB959209) x86 Windows Server 2003 Security Update for Windows Server 2003 (KB958687) Thanks for any light you can shed on this.

  Read the article

• Routing subnet over GRE tunnel

  - by eMgz

  Hi, Im trying to configure a GRE over IPSec connection between two subnets. The IPSec tunnel is opened and now I want to add a GRE tunnel over it: ip tunnel add GRE01 mode gre remote 10.244.0.1 local 10.244.245.32 ttl 255 ip link set GRE01 up ip addr add 10.244.248.126 dev GRE01 ip route add 10.244.248.125 dev GRE01 Now I have an interface GRE01 (ifconfig): GRE10 Link encap:UNSPEC HWaddr <h_addr> inet addr:10.244.248.126 P-t-P:10.244.248.126 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MTU:1476 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And the following routes (ip route list): 10.244.248.125 dev GRE10 scope link <pub_subnet> dev eth0 proto kernel scope link src <pub_ip> default via <pub_gw> dev eth0 metric 100 As a last step, I need now to route my subnet over the tunnel: ip route add 10.245.1.224/28 10.244.248.125 However, I am getting the error Error: either "to" is duplicate, or "10.244.248.125" is a garbage. So, what I didn't understand is why I can't route my subnet over the tunnel, once the only route I have there says that it should route the tunnel IP over the GRE01 interface. Any hint? Thanks.

  Read the article

• Ubuntu 64bit Xen DomU Issues after upgrade from Karmic to Lucid

  - by Shoaibi

  I was upgrading my servers today and it all went fine except the last machine which has the following issues: [Resolved using http://www.ndchost.com/wiki/server-administration/upgrade-ubuntu-pre-10.04#post-1004-upgradefinal-steps] No login prompt on console Done. Begin: Mounting root file system... ... Begin: Running /scripts/local-top ... Done. [ 0.545705] blkfront: xvda: barriers enabled [ 0.546949] xvda: xvda1 [ 0.549961] blkfront: xvde: barriers enabled [ 0.550619] xvde: xvde1 xvde2 Begin: Running /scripts/local-premount ... Done. [ 0.870385] kjournald starting. Commit interval 5 seconds [ 0.870449] EXT3-fs: mounted filesystem with ordered data mode. Begin: Running /scripts/local-bottom ... Done. Done. Begin: Running /scripts/init-bottom ... Done. Also tried by pressing ENTER and CTRL+C many times, no use. Resolved: [/tmp was mounted as noexec, changing that fix it]: I get errors when i try to re-install udev in single user mode: Unpacking replacement udev ... Processing triggers for ureadahead ... ureadahead will be reprofiled on next reboot Processing triggers for man-db ... Setting up udev (151-12.1) ... udev start/running, process 1003 Removing `local diversion of /sbin/udevadm to /sbin/udevadm.upgrade' update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-2.6.32-25-server /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/local-premount/fixrtc: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/local-premount/ntfs_3g: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/local-premount/resume: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/nfs-top/udev: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/panic/console_setup: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/init-top/all_generic_ide: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/init-top/blacklist: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/init-top/udev: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/init-bottom/udev: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/local-bottom/ntfs_3g: Permission denied

  Read the article

• Possible DNS Injection and/or SSL hijack?

  - by Anthony

  So if I go to my site without indicating the protocol, I'm taken to: http://example.org/test.php But if I go directly to: https://example.org/test.php I get a 404 back. If I go to just: https://example.org I get a totally different site (a page about martial arts). I went to the site via https not very long ago (maybe a week?) and it was fine. This is a shared server, as I understand it, and I do not have shell access, so I'm limited to the site's CPanel to do any further investigations. But when I go to: example.org:2083 I'm taken to https://example.org:2083, which, if someone has taken over the SSL port, could mean they have taken over the 2083 part as well (at least in my paranoid mind). I'm made more nervous by the fact that the cpanel login page at the above address looks very new (better, really) compared to the last time I went to it over the weekend. It's possible that wires got crossed somewhere after a system update, but I don't want to put in my name username and password in case it's a phishing attempt. Is there any way to know for sure without shell access to know for sure if someone has taken over? If I look up the IP address for the host name, the IP address matches what I have on a phpinfo page I can get to over http. If I go to the IP address directly on port 2083, I get the same login mentioned above (new and and suspiciously nice). But the SSL cert shows as good when I go this route. So if that's the case (I know the IP is right, the cert checks out, and there isn't any DNS involved), is that enough to feel safe at that point of entry? Finally, if I can safely log in via the IP, does anyone have any advice on where to check first on CPanel for why the SSL port is forwarding to a site on karate? Thanks.

  Read the article

• Courier-imap login problem after upgrading / enabling verbose logging

  - by halka

  I've updated my mail server last night, from Debian etch to lenny. So far I've encountered a problem with my postfix installation, mainly that I managed to broke the IMAP access somehow. When trying to connect to the IMAP server with Thunderbird, all I get in mail.log is: Feb 12 11:57:16 mail imapd-ssl: Connection, ip=[::ffff:10.100.200.65] Feb 12 11:57:16 mail imapd-ssl: LOGIN: ip=[::ffff:10.100.200.65], command=AUTHENTICATE Feb 12 11:57:16 mail authdaemond: received auth request, service=imap, authtype=login Feb 12 11:57:16 mail authdaemond: authmysql: trying this module Feb 12 11:57:16 mail authdaemond: SQL query: SELECT username, password, "", '105', '105', '/var/virtual', maildir, "", name, "" FROM mailbox WHERE username = '[email protected]' AND (active=1) Feb 12 11:57:16 mail authdaemond: password matches successfully Feb 12 11:57:16 mail authdaemond: authmysql: sysusername=<null>, sysuserid=105, sysgroupid=105, homedir=/var/virtual, [email protected], fullname=<null>, maildir=xoxo.sk/[email protected]/, quota=<null>, options=<null> Feb 12 11:57:16 mail authdaemond: Authenticated: sysusername=<null>, sysuserid=105, sysgroupid=105, homedir=/var/virtual, [email protected], fullname=<null>, maildir=xoxo.sk/[email protected]/, quota=<null>, options=<null> ...and then Thunderbird proceeds to complain that it cant' login / lost connection. Thunderbird is definitely not configured to connect through SSL/TLS. POP3 (also provided by Courier) is working fine. I've been mainly looking for a way to make the courier-imap logging more verbose, like can be seen for example here. Edit: Sorry about the mess, I've found that I've been funneling the log through grep imap, which naturally didn't display entries for authdaemond. The verbose logging configuration entry is found in /etc/courier/imapd under DEBUG_LOGIN=1 (set to 1 to enable verbose logging, set to 2 to enable dumping plaintext passwords to logfile. Careful.)

  Read the article

• Vista laptop 1 connects to network but Vista laptop 2 doesn't

  - by Jaips

  (Sorry if this is a dulipcate. I did a hunt but couldn't find matching question) We recently got a new router for our network (thomson TG585v8). It was already pre-configured by the ISP and was easy to setup. Both Vista laptops in this home network connected without trouble as well a iPod touch, all via wifi. In the last two days one of the laptops has been unable to connect cleanly to the network (connects as unidentified network). The other laptop, and iPod have not had any issues. I can't think of anything that has changed to make this happen now. I have rebooted the laptop and the router. I have updated the laptop wireless driver I have checked the laptop is set to automatically get IP I have logged into the router which correctly identifies all three wireless devices. The problem laptop connects via LAN without issue. Some things that may or may not matter: The problem laptop also sometimes uses a 3G dongle Both laptops use Windows Live Mesh to sync folders Laptop is usually set to go to sleep NB: it seems this is an intermittent issue, after an hour (since i noticed it) it seems to have fixed itself. Would love ideas though to solve this problem for good.

  Read the article

• Why cache static files with Varnish, why not pass

  - by Saif Bechan

  I have a system runnning nginx / php-fpm / varnish / wordpress and amazon s3. Now I have looked at a lot of configuration files while setting up the system, and in all of them I found something like this: /* If the request is for pictures, javascript, css, etc */ if (req.url ~ "\.(jpg|jpeg|png|gif|css|js)$") { /* Remove the cookie and make the request static */ unset req.http.cookie; return (lookup); } I do not understand why this is done. Most of the examples also run NginX as a webserver. Now the question is, why would you use the varnish cache to cache these static files. It makes much more sense to me to only cache the dynamic files so that php-fpm / mysql don't get hit that much. Am I correct or am I missing something here? UPDATE I want to add some info to the question based on the answer given. If you have a dynamic website, where the content actually changes a lot, chaching does not make sense. But if you use WordPress for a static website for example, this can be cached for long periods of time. That said, more important to me is static conent. I have found a link with some test and benchmarks on different cache apps and webserver apps. http://nbonvin.wordpress.com/2011/03/14/apache-vs-nginx-vs-varnish-vs-gwan/ NginX is actually faster in getting your static content, so it makes more sense to just let it pass. NginX works great with static files. -- Apart from that, most of the time static content is not even in the webserver itself. Most of the time this content is stores on a CDN somewhere, maybe AWS S3, something like that. I think the varnish cache is the last place where you want to have you static content stored.

  Read the article

• TFTP Timing Out on Ubuntu VM

  - by valsidalv

  I'm running a Windows 7 PC with VMware installed which has my Ubuntu (10.04 Lucid Lynx). I recently installed a DHCP server and TFTP (Xinet tftpd) using these instructions. I've mapped a network drive so that my Windows has access to all the files in my VM through a 192.x.x.x IP address. I'm trying to throw some custom firmware onto a router. The router has its own built-in TFTP utility that will download the image. It successfully manages to do everything but it is slow because it writes it to flash memory. There is another method that is much quicker because it writes to RAM directly but it must use the TFTP server in Ubuntu. The issue I'm facing is that the Ubuntu TFTP transfer seems to be timing out. The transfer starts but never goes past ~60%. Here's my /etc/xinetd.d/tftp file (similar to a known working config): service tftp { protocol = udp port = 69 socket_type = dgram wait = yes user = nobody server = /usr/sbin/in.tftpd server_args = -s /home/user/tftp/ disable = no cps = 300 2 per_source = 60 } I've done some searching but can't find any parameters for this file to control timeout time or number of retries. The last two arguments (cps, per_source) and completely alien to me (can anyone explain). I have a few possible solutions but the easiest would be to get this TFTP server working. Can anyone help? Either with a timeout configuration or maybe even recommend a different TFTP server? Thanks!

  Read the article

• What can I do to prevent system power downs?

  - by Joe King

  Yesterday I was given my brother's old laptop - core i7, 2.67GHz, 8GB RAM, 128GB SSD, Win7 64 bit. It's a Sony Vaio Z11. Approx 18 months old. When running something computationally intensive, the fan starts up and after about 30 secs it just powers itself down with no warning. I guess it is overheating. There is nothing in the event logs to suggest what is causing it - the only thing I see is "the last system shutdown was unexpected" or something similar. This is a problem for me because I use a lot of number crunching apps, which pretty much makes it useless to me. I would like to know if there is anything I can do, other than the obvious things I've done already - open up and clean out dust, re-install the OS. According to my brother, this problem started about 6 months ago when it was already outside warranty. If it's just used for simple things - web browsing, word processing etc, the problem does not occur. Any ideas for what I can do to fix this ? Update: I found that the laptop has 2 hardware settings for graphics: Speed and Stamina - the Speed setting seems to use an nvidia GEforce GT 330M, while the Stamina setting uses an Intel chipset. With the setting on Speed, I can hear the fan the whole time, and the system powers down after a short while (5-10 mins) even just doing basic tasks (browsing this site for example), but doesn't shut down if I just leave it switched on. In this mode it also sometimes just freezes the screen and I have to power off myself. However on Stamina setting it only powers down when doing number crunching and never freezes the screen.

  Read the article

• Juniper’s Network Connect ncsvc on Linux: “host checker failed, error 10”

  - by hfs

  I’m trying to log in to a Juniper VPN with Network Connect from a headless Linux client. I followed the instructions and used the script from http://mad-scientist.us/juniper.html. When running the script with --nogui switch the command that gets finally executed is $HOME/.juniper_networks/network_connect/ncsvc -h HOST -u USER -r REALM -f $HOME/.vpn.default.crt. I get asked for the password, a line “Connecting to…” is printed but then the programm silently stops. When adding -L 5 (most verbose logging) to the command line, these are the last messages printed to the log: dsclient.info state: kStateCacheCleaner (dsclient.cpp:280) dsclient.info --> POST /dana-na/cc/ccupdate.cgi (authenticate.cpp:162) http_connection.para Entering state_start_connection (http_connection.cpp:282) http_connection.para Entering state_continue_connection (http_connection.cpp:299) http_connection.para Entering state_ssl_connect (http_connection.cpp:468) dsssl.para SSL connect ssl=0x833e568/sd=4 connection using cipher RC4-MD5 (DSSSLSock.cpp:656) http_connection.para Returning DSHTTP_COMPLETE from state_ssl_connect (http_connection.cpp:476) DSHttp.debug state_reading_response_body - copying 0 buffered bytes (http_requester.cpp:800) DSHttp.debug state_reading_response_body - recv'd 0 bytes data (http_requester.cpp:833) dsclient.info <-- 200 (authenticate.cpp:194) dsclient.error state host checker failed, error 10 (dsclient.cpp:282) ncapp.error Failed to authenticate with IVE. Error 10 (ncsvc.cpp:197) dsncuiapi.para DsNcUiApi::~DsNcUiApi (dsncuiapi.cpp:72) What does host checker failed mean? How can I find out what it tried to check and what failed? The HostChecker Configuration Guide mentions that a $HOME/.juniper_networks/tncc.jar gets installed on Linux, but my installation contains no such file. From that I concluded that HostChecker is disabled for my VPN on Linux? Are the POST to /dana-na/cc/ccupdate.cgi and “host checker failed” connected or independent? By running the connection over a SSL proxy I found out that the POST data is status=NOTOK (Funny side note: the client of the oh-so-secure VPN does not validate the server’s SSL certificate, so is wide open to MITM attacks…). So it seems that it’s the client that closes the connection and not the server.

  Read the article

• Firebox 1250e Core Failing?

  - by Noah

  We have 2 Firebox 1250e Core firewall boxes in our production environment, serving as an active and passive mode. A few months back, the active box was flashing a warning light, so our consultant removed it, and plugged it in to a test network. Everything appeared to be working fine, so he reloaded it into the production environment, and we didn't see any other issues. Fast forward to last week, and out network was constantly dropping connections over RDC, timing out, and performing as if there was a traffic issue. I turned off the production box and everything began to work fine immediately. At this point though, I'm not sure how to proceed. Should the box be completely replaced? Is there any recommended testing we could do to determine if there is a failure of some type with this device? Should we try upgrading the software on it? I know the environment isn't the issue, since the passive box (which is now the active one) is working fine. We'd like to have 2 in production though for safety failover purposes. I am not a network admin, but am hoping someone here might be able to provide some guidance.

  Read the article

• My linux server "Number of processes created" and "Context switches" are growing incredibly fast

  - by Jorge Fuentes González

  I have a strange behaviour in my server :-/. Is a OpenVZ VPS (I think is OpenVZ, because /proc/user_beancounters exists and df -h returns /dev/simfs drive. Also ifconfig returns venet0). When I do cat /proc/stat, I can see how each second about 50-100 processes are created and happens about 800k-1200k context switches! All that info is with the server completely idle, no traffic nor programs running. Top shows 0 load average and 100% idle CPU. I've closed all non-needed services (httpd, mysqld, sendmail, nagios, named...) and the problem still happens. I do ps -ALf each second too and I don't see any changes, only a new ps process is created each time and the PID is just the same as before + 1, so new processes are not created, so I thought that process growing in cat /proc/stat must be threads (Yes, seems that processes in /proc/stat counts threads creation too as this states: http://webcache.googleusercontent.com/search?q=cache:8NLgzKEzHQQJ:www.linuxhowtos.org/System/procstat.htm&hl=es&tbo=d&gl=es&strip=1). I've changed to /proc dir and done cat [PID]\status with all PIDs listed with ls (Including kernel ones) and in any process voluntary_ctxt_switches nor nonvoluntary_ctxt_switches are growing at the same speed as cat /proc/stat does (just a few tens/second), Threads keeps the same also. I've done strace -p PID to all process too so I can see if any process is crating threads or something but the only process that has a bit of movement is ssh and that movement is read/write operations because of the data is sending to my terminal. After that, I've done vmstat -s and saw that forks is growing at the same speed processes in /proc/stat does. As http://linux.die.net/man/2/fork says, each fork() creates a new PID but my server PID is not growing! The last thing I can think of is that all process data that proc/stat and vmstat -s show is shared with all the other VPS stored in the same machine, but I don't know if that is correct... If someone can throw some light on this I would be really grateful.

  Read the article

• What is the best way to recover from a mysql replication fail?

  - by Itai Ganot

  Today, the replication between our master mysql db server and the two replication servers dropped. I have a procedure here which was written a long time ago and i'm not sure it's the fastest method to recover for this issue. I'd like to share with you the procedure and I'd appreciate if you could give your thoughts about it and maybe even tell me how it can be done quicker. At the master: RESET MASTER; FLUSH TABLES WITH READ LOCK; SHOW MASTER STATUS; And copy the values of the result of the last command somewhere. Wihtout closing the connection to the client (because it would release the read lock) issue the command to get a dump of the master: mysqldump mysq Now you can release the lock, even if the dump hasn't end. To do it perform the following command in the mysql client: UNLOCK TABLES; Now copy the dump file to the slave using scp or your preferred tool. At the slave: Open a connection to mysql and type: STOP SLAVE; Load master's data dump with this console command: mysql -uroot -p < mysqldump.sql Sync slave and master logs: RESET SLAVE; CHANGE MASTER TO MASTER_LOG_FILE='mysql-bin.000001', MASTER_LOG_POS=98; Where the values of the above fields are the ones you copied before. Finally type START SLAVE; And to check that everything is working again, if you type SHOW SLAVE STATUS; you should see: Slave_IO_Running: Yes Slave_SQL_Running: Yes That's it! At the moment i'm in the stage of copying the db from the master to the other two replication servers and it takes more than 6 hours to that point, isn't it too slow? The servers are connected through a 1gb switch.

  Read the article

< Previous Page | 490 491 492 493 494 495 496 497 498 499 500 501  | Next Page >