Search Results

Search found 14738 results on 590 pages for 'outlook settings'.

Page 494/590 | < Previous Page | 490 491 492 493 494 495 496 497 498 499 500 501  | Next Page >

• How to completely disable IPv6 for loopback interface on RHEL 5.6

  - by Marc D

  I've done lots of research on how to disable IPv6 on RedHat Linux and I have it almost completely disabled. However the loopback interface is still getting an inet6 loopback address (::1/128). I can't find where IPV6 is still enabled for loopback. To disable IPV6 I added the following settings to /etc/sysctl.conf: net.ipv6.conf.default.disable_ipv6=1 net.ipv6.conf.all.disable_ipv6=1 And also added the following line to /etc/sysconfig/network: NETWORKING_IPV6=no After rebooting, the inet6 address is gone from my physical interface (eth0), but is still there for lo: # ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:50:56:xx:xx:xx brd ff:ff:ff:ff:ff:ff inet 10.x.x.x/21 brd 10.x.x.x scope global eth0 If I manually remove the IPV6 address from loopback and then bounce the interface, it comes back: # ip addr del ::1/128 dev lo # ip addr show lo 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo # ip link set lo down # ip link set lo up # ip addr show lo 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever I believe IPV6 should be disabled at the kernel level as confirmed by sysctl: # sysctl net.ipv6.conf.lo.disable_ipv6 net.ipv6.conf.lo.disable_ipv6 = 1 Any ideas on what else would cause the loopback interface to get an IPV6 address?

  Read the article

• Trying to communicate between virtual servers on the same host through ipv6

  - by Daniele Testa

  I am running KVM on a host with 2 virtual servers. Each virtual server has a own bridge interface on the host VPS1 has br1 VPS2 has br2 Each virtual server has a own ipv4 and a ipv6. The virtual servers has no problem communicating with internet or with eachother through ipv4. However, with ipv6, they can only communicate with internet and NOT with eachother. The host can ping the 2 virtual servers without any problems, but they cannot ping eachother. iptables has been set to ACCEPT on all chains, so it is not the problem. VPS1 has ipv6 = 2a01:4f8:xxx:xxx::10 VPS2 has ipv6 = 2a01:4f8:xxx:xxx::5 the host has the following routes set: ip route add 2a01:4f8:xxx:xxx::10 dev br1 ip route add 2a01:4f8:xxx:xxx::5 dev br2 When I do a ping from VPS2 to VPS1, I see the following on the host: tcpdump -i br1 15:32:27.704404 IP6 2a01:4f8:xxx:xxx::10 > ff02::1:ff00:5: ICMP6, neighbor solicitation, who has 2a01:4f8:xxx:xxx::5, length 32 So it seems like the host is seeing the request coming from VPS1 on br1. But for some reason, it does not forward it to br2. Instead it is asking where the destination IP is through ipv6 multicast. Anyone has a clue what is going on? I find this very strange, as it is working fine with ipv4 with the exact same settings and routes.

  Read the article

• How can I configure myhostname to work with Postfix?

  - by John Kelly Ferguson

  I'm going through the process of setting up a Discourse forum on my server (Ubuntu 12.04 x64) and am getting stuck at the point where I have to configure mailers. I'm following Discourse's instructions and am stuck trying to configure postfix for Mandrill. It is says to check my fully-qualified domain name by typing hostname -f When I enter in hostname -f, I get localhost. As far as I know, entering in hostname -f should return mydomainname.com. When I just enter in hostname, I get mydomainname which is correct because that is what I set my hostname to in /etc/hostname. Looking at some of my other settings, my /etc/hosts file reads: 127.0.0.1 localhost mydomainname # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters And in my /etc/postfix/main.cf file, I have myhostname set like this: myhostname = mydomainname.mydomainname.com (Should this be myhostname = mail.mydomainname.com instead?) And mydestination is the following: mydestination = mydomainname.com, localhost, localhost.localdomain, localhost I'm not that familiar with configuring hostnames. I've been reading Postfix's instructions, but haven't been able to figure it out yet. Any help on how to get this to work would be greatly appreciated. Thanks.

  Read the article

• Apache2 doesn't serve PHP-scripts correctly

  - by cmbrnt

  I've run into a problem with my Apache 2.2.16 configuration, running on Debian Squeeze. The problem is that it stopped serving PHP5-scripts completely. When I try to access the sites with Google Chrome, it instead downloads a file called "download", which contains the contents of the script. This is of course not a good thing. It does serve common html-files perfectly... I've been at this for quite a while now, and after all the googling and troubleshooting, I thought it would be a good time to ask you guys. Here's what I've got: The php5 and libapache2-mod-php5 packages are installed /etc/apache2/mods-available contains both php5.load and php5.conf, and these are symlinked from the mods-enabled directory The /etc/php5/ directory is left untouched since the installation. Here's the contents of /etc/apache2/mods-available/php.load: LoadModule php5_module /usr/lib/apache2/modules/libphp5.so And /etc/apache2/mods-available/php.conf: <IfModule mod_php5.c> <FilesMatch "\.ph(p3?|tml)$"> SetHandler application/x-httpd-php </FilesMatch> <FilesMatch "\.phps$"> SetHandler application/x-httpd-php-source </FilesMatch> <IfModule mod_userdir.c> <Directory /home/*/public_html> php_admin_value engine Off </Directory> </IfModule> </IfModule> What am I missing? This is a server with modified virtual hosts and the like, so I might have changed some settings which causes this problem, but simply purging and reinstalling is not an option so far, since the configuration is quite extensive. Any help would be great. Thanks.

  Read the article

• How do I configure VMware View location-based printing to use Active Directory Groups?

  - by Jason Pearce

  I am attempting to configure VMware View 4.5's Location-Based Printing, which leverages an included OEM version of ThinPrint, to assign printers to active directory groups. The location-based printing feature maps printers that are physically near client systems to VMware View desktops. I am using the Active Directory group policy setting AutoConnect Location-based Printing for VMware View, which is located in the Microsoft Group Policy Object Editor in the Software Settings folder under Computer Configuration. The AutoConnect Location-based Printing for VMware View appearst to be just a name translation table. It permits me to assign a specific printer or printers to an IP Range, Client Name, Mac Address, User, or User Group. I'm attempting to assign printers to active directory user groups. I have created a new active directory group for each printer that I intend to use in VMware View desktop pools. I will then assign active directory users to the active directory groups that represent each network printer. Example: doej is a member of the PTR-FLOOR2-NORTH-ROOM255 active directory group. Using AutoConnect, I assigned the group to receive a network printer by adding PTR-FLOOR2-NORTH-ROOM255 in the User/Group column. Problem: When doej logs in to his VDI session, the printer is not present. However, if I use a wildcard "*" in the User/Group column instead of the specific PTR-FLOOR2-NORTH-ROOM255 active directory group, the printer is present and functions as designed. Alternatives: I have tried assigning printers to active directory groups within AutoConnect in the following ways, all unsuccesfull: PTR-FLOOR2-NORTH-ROOM255 domainexample\PTR-FLOOR2-NORTH-ROOM255 domainexample.local\PTR-FLOOR2-NORTH-ROOM255 Confirmation: The information used to map the printer to the VMware View desktop is stored in a registry entry on the View desktop in HKEY_LOCAL_MACHINE\SOFTWARE\Policies\thinprint\tpautoconnect. For each of these examples, I have reviewed the registry entry and can confirm that the desktop is receiving the information from the AutoConnect translation table. Summary: Can anyone provide an example of how to configure VMware View 4.5's Location-Based Printing so that I may assign network printers to active directory groups via the included AutoConnect tool? I would welcome a clear example of a working configuration. Thank you.

  Read the article

• Connection failed between Windows Servers

  - by Kerby82

  I'm setting up an infrastructure based on Windows Server 2012. The firewall is turned off and I can't access the Domain controller to check for the group policy. I'm experiencing some connection problem between servers. All the servers are running a site on the TCP Port 80 and I check with netstat that the web server is binding on every Ip of the servers. If i try to telnet from the server itself on the port 80 it works (using DNS name) if I try same telnet from another machine I get connection failed. The DNS works, the ping is successfull, the servers are on the same subnet, the firewall is turned off (even though windows advanced firewall says that some settings can be managed by the System Administrator, i guess group policy). I don't know how to troubleshoot further. Do you have any idea? Is that possible that the FW looks turned off but there are some group policy blocking the connections? (I also check group policy-Administrative Template-Network Connections- Windows FW everything is not configured) I need some hint on how to keep troubleshooting such a problem.

  Read the article

• Updated my WAMP Server and MySQL is eating up 580mB of memory

  - by Jon

  I updated my dev-box's WAMPSERVER, and along with updating PHP and Apache, MySQL updated to '5.6.12'. After doing that, I copied the data folder from my old (5.1.36) install to the new one and now MySQL takes up 580mB which is way too much, since I'm the only person using it (Locally) and there are only 20 or so databases on it, none of which have 'memory' tables. How can I get this down to a decent amount? My my.ini: # For advice on how to change settings please see # http://dev.mysql.com/doc/refman/5.6/en/server-configuration-defaults.html # *** DO NOT EDIT THIS FILE. It's a template which will be copied to the # *** default location during install, and will be replaced if you # *** upgrade to a newer version of MySQL. [mysqld] # Remove leading # and set to the amount of RAM for the most important data # cache in MySQL. Start at 70% of total RAM for dedicated server, else 10%. # innodb_buffer_pool_size = 128M # Remove leading # to turn on a very important data integrity option: logging # changes to the binary log between backups. # log_bin # These are commonly set, remove the # and set as required. # basedir = ..... # datadir = ..... # port = ..... # server_id = ..... # Remove leading # to set options mainly useful for reporting servers. # The server defaults are faster for transactions and fast SELECTs. # Adjust sizes as needed, experiment to find the optimal values. # join_buffer_size = 128M # sort_buffer_size = 2M # read_rnd_buffer_size = 2M sql_mode=NO_ENGINE_SUBSTITUTION,STRICT_TRANS_TABLES Database info: Storage Engine Data Size Index Size Total Size InnoDB 48.00 KB 0.00 B 48.00 KB MEMORY 0.00 B 0.00 B 0.00 B MyISAM 163.64 MB 122.49 MB 286.13 MB Total 163.69 MB 122.49 MB 286.18 MB

  Read the article

• Changing the default boot option without losing the boot menu

  - by hvd

  I've had a working multi-boot setup with the Windows boot loader, containing menu items for two Windows 7 systems, and one for Grub. Grub in turn contains multiple menu items, but I think that's not relevant here. I've upgraded one system to Windows 8. When I now set a different system as the default, I lose the boot menu, and I lose the possibility of booting into the other systems. I've set Windows 7 as the default, rebooted, and get Windows 7, but I don't get to choose which system to boot into. I can run its own bcdedit to change the default back to Windows 8, and another reboot shows the boot menu again, but how can I avoid defaulting to Windows 8? Here are my current boot settings, is there anything that is misconfigured? C:\WINDOWS\system32>bcdedit Windows Boot Manager -------------------- identifier {bootmgr} device partition=F: description Windows Boot Manager locale nl-NL inherit {globalsettings} integrityservices Enable default {current} resumeobject {2f8b77f0-a30b-11e1-a9c6-a4bd8d37f662} displayorder {current} {2f8b77e3-a30b-11e1-a9c6-a4bd8d37f662} {2f8b77ee-a30b-11e1-a9c6-a4bd8d37f662} toolsdisplayorder {memdiag} timeout 30 Windows Boot Loader ------------------- identifier {current} device partition=C: path \WINDOWS\system32\winload.exe description Windows 8 locale nl-NL inherit {bootloadersettings} integrityservices Enable recoveryenabled No allowedinmemorysettings 0x15000075 osdevice partition=C: systemroot \WINDOWS resumeobject {2f8b77f0-a30b-11e1-a9c6-a4bd8d37f662} nx OptIn bootmenupolicy Standard Windows Boot Loader ------------------- identifier {2f8b77e3-a30b-11e1-a9c6-a4bd8d37f662} device partition=D: path \Windows\system32\winload.exe description Windows 7 locale nl-NL osdevice partition=D: systemroot \Windows resumeobject {59616f59-a2ba-11e1-b73a-806e6f6e6963} nx OptIn pae Default bootmenupolicy Standard hypervisorlaunchtype Auto detecthal Yes sos No debug No Real-mode Boot Sector --------------------- identifier {2f8b77ee-a30b-11e1-a9c6-a4bd8d37f662} device partition=C: path \grub\winloader\grub.boot description Grub 2

  Read the article

• VT-x not enabled on 2010 Mac Pro

  - by BlindingDawn

  To start I had a Hackintosh as per the instructions from Lifehacker.com before and moved everything to a new 2010 8 Core Mac Pro. I opted for a restore from the time machine backup rather than using the migration assistance. I believe this may have caused more problems but one in particular is the lack of VT-x support. When I checked Parallels Desktop under "Host Hardware" information, I get the following that shows that VT-x isn't enabled. <Cpu dyn_lists=""> <Number>16</Number> <Model>Intel(R) Xeon(R) CPU E5620 @ 2.40GHz</Model> <Mode>1</Mode> <Speed>2400</Speed> <VtxEnabled>0</VtxEnabled> <VtxMode>1</VtxMode> 1) Does Parallels Desktop support using VT-x? 2) Does this setting show that my VT-x isn't enabled? 3) Is there a way of fixing it so that it is enabled? 4) Is there a way of using my Time Machine backup as if I'm doing a restore using migration assistance and just restore the files and settings?

  Read the article

• Setup: Eclipse in Ubuntu with Apache2 and Subversion

  - by Ricalsin

  Trying to setup Eclispe. I am running ubuntu 10.10 (Maverick). Apache2.2.16 Subversion 1.6.12 The Eclipse help/about/installed software says: Eclipse Platform 3.5.2 Subclipse 1.0.0 Version Control with Subversion 1.1.1 The Subclips wiki I followed is here I have installed the libsvn-java app as discussed. I added the line "-Djava.library.path=/usr/lib/jni" to the eclipse.ini file I checked the Eclipse help/about/confirguration settings and both of these lines are listed: eclipse.vmargs=-Djava.library.path=/usr/lib/jni java.library.path=/usr/lib/jni I checked that those files are in those directories. Still, when I check the preferencesteamsvn an error dialog shows: Failed to load JavaHL Library. These are the errors that were encountered: no libsvnjavahl.1 in java.library.path Incompatible JavaHL library loaded 1.3.x or later required I followed the "Testing JavaHL libraries" troubleshooting section at the bottom of the wiki: I downloaded the tarbal and ran it in a folder on my desktop with no problems. Then, I followed the instructions and placed that file INSIDE the path (usr/lib/jni/testJavaHL) and ran it from there. There are 50 tests performed and each one of them came back with this same error (posting only one for brevity): 50) testCommitRevprops(org.tigris.subversion.javahl.BasicTests)java.io.FileNotFoundException: /usr/lib/jni/testJavaHL/local_tmp/greek_files/iota (No such file or directory) at java.io.FileOutputStream.open(Native Method) at java.io.FileOutputStream.<init>(FileOutputStream.java:209) at java.io.FileOutputStream.<init>(FileOutputStream.java:160) at org.tigris.subversion.javahl.WC.materialize(WC.java:70) at org.tigris.subversion.javahl.SVNTests.buildGreekFiles(SVNTests.java:303) at org.tigris.subversion.javahl.SVNTests.setUp(SVNTests.java:222) at org.tigris.subversion.javahl.RunTests.main(RunTests.java:111) FAILURES!!! Tests run: 50, Failures: 0, Errors: 50 Any ideas as to how/why the "local_tmp/greek_files/iota" is appended to the directory? I assume that's my problem.. I'm also having a problem with newrepository location = ...as the directory location of my svn repository is one level above the home directory - which is prepended to whatever I place in the dialog box - resulting in this error: svn: '/home/ricalsin/file:/home/svn' does not exist Thank you for any help.

  Read the article

• VMWare web UI intermittent access on CentOS

  - by PeteWilliams

  I've got a CentOS 5.2 server that I'm trying to get set up as a development environment. As part of this, I planned to install VMWare Server 2 and set up several virtual development servers. I've got as far as installing VMWare Server 2 but access to the remote control panel is only working intermittently. If I access it through Firefox at https://127.0.0.1:8333/ui/# it usually says either: "Connection intterupted: connection was reset before the page loaded" Or "Firefox can't establish a connection to the server at 127.0.0.1" But every now and then it lets me in and I'll manage a few clicks in the web UI before it kicks me out with the following error: "The server could not complete a request (HTTP 0 ). The server encountered an unexpected condition that prevented it from fulfilling the request. If this problem persists, please contact your system administrator." I've done all the updates available in CentOS except one OpenOffice one that is causing a conflict, and I re-ran wmware-config.pl after updating the kernel. Though I went with all the defaults as I don't really know what I'm doing! I've since rebooted and nothing changed. I've also tried accessing the control panel remotely from another machine in the network and the results are the same. Does anyone have any ideas what might be causing this and how I can resolve it? I'm afraid I'm a developer playing at sys-admin, so I may be missing something obvious! Many thanks Pete Update I have now reinstalled both the operating system and VMWare and I'm still getting the same issue. I wonder if it's a result of the settings I'm putting in on the config.pl script..?

  Read the article

• How do I restore to a delta file (disk) on Vmware ESXi

  - by Oscar

  Using VMware Server ESXi (freebie version) I have a Virtual Machine (win 2k3 r2 server). When I first provisioned it I took a snapshot of it. I recently tried to clone the primary drive using my standard hardware-based method to grow a windows disk. (using knoppix, clone drive to a new drive, make it bootable, then I intended to extend the partition via diskpart from within windows). This process failed; I tried setting the cloned drive (via the vmware gui) to replace the original drive, boot and be done. This didn't work out so well. The machine never booted. I checked the boot order, the disk location and all the basics I usually do. As a failsafe, I then tried changing all the settings back so the machine would boot to the original drive and I could figure out (as I eventually did) a better way of growing the disk. However when I powered on the machine with the original drive, it reverted back to that initial snapshot I created; It lost all the changes since. I looked in the file system and found a few files, I think the keyfile here is one named "delta" and I'm assuming that's the disk I want, but I can't find a way to have the Virtual Machine actually use that drive/file. It isn't available to add when I go to add an existing drive. Do I need to somehow commit that delta to the original drive and then boot from it again? Can you point me in the right direction? I've since discovered the proper way of growing drives using "vmkfstools" but I need to get back to the original state of the machine to try this out. Any help would be greatly appreciated.

  Read the article

• windows 7 monitor instantly resumes from power off

  - by user167328

  It seems that some service or program is preventing my monitor from going into power save mode but I cannot find a way to dig down the cause. Does anybody know a way to find out which event may be causing the problem? Background information: If I leave/lock my computer I want to immediately power off the monitor. Stupid windows has no program for this so I use a third party utility. I use Display.exe from Noel Danjou since 2005 and have had no problem with it on XP, my Notebook with w7 x64 pro and at the office with w7 x64 enterprise. With my new home pc with w7 x64 pro the monitor goes off but instantly comes back on after a second. So I tested using a power plan with the shortest timeout of 1 minute but with that the display never goes off at all. (Setting a power plan timeout is no useful option because then I cannot read a document or watch a movie without the monitor going off) I could try trial and error methods but this is cumbersome and not what I regard as a professional solution. So I would prefer a way to analyze the windows events to find out the reason for the display staying active. Add On: In the meantime I tried safe mode and also exited from all tray programs but the problem is still there. I also checked the BIOS for special power settings but still no solution (P.S. Mobo is H87-G41 PC Mate with latest BIOS rev.)

  Read the article

• High fan speed with no reason

  - by Klaus

  For a few weeks, the fans of my Lenovo B590 laptop, running on Xubuntu 14, turn to high speed a few minutes after it is turned on. The fans won't speed down until I turn the computer off. This is quite strange, since This didn't happen before The temperatures are quite low (are they ?) $sensors Adapter: Virtual device temp1: +36.0°C (crit = +88.0°C) temp2: +30.0°C (crit = +126.0°C) coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +37.0°C (high = +72.0°C, crit = +90.0°C) Core 0: +34.0°C (high = +72.0°C, crit = +90.0°C) Core 1: +31.0°C (high = +72.0°C, crit = +90.0°C) thinkpad-isa-0000 Adapter: ISA adapter fan1: 0 RPM pkg-temp-0-virtual-0 Adapter: Virtual device temp1: +37.0°C $sudo hddtemp /dev/sda /dev/sda: ST500LT012-9WS142: 33°C The computer is under low load: top - 08:30:15 up 16 min, 2 users, load average: 0.28, 0.23, 0.23 Tasks: 197 total, 1 running, 196 sleeping, 0 stopped, 0 zombie %Cpu(s): 0.8 us, 0.5 sy, 0.0 ni, 98.7 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st KiB Mem: 3607944 total, 1973956 used, 1633988 free, 99660 buffers KiB Swap: 3744764 total, 0 used, 3744764 free. 789936 cached Mem The BIOS is up to date (and there are no fan settings in it) The fan is clean and dust-free Why would the BIOS turn the fans to high speed where there seem to be no reason for that ? It seems that we cannot control the fan manually with this model, so I guess the only solution is to understand why this happens.

  Read the article

• Converting PDF eBooks into a Kindle format

  - by Ender

  Over the past couple of years I've amassed quite a collection of guides, tutorials and ebooks in PDF format. A lot of these are quite useful for work, especially PDF documentation, and rather than have to be at a computer every time I want to read how to do something in Sitecore or to read through a software testing ebook I'd like to do it on my brand-spanking-new Kindle. However, even though there is now a native PDF reader on the Kindle due to the nature of PDF's they are practically unreadable. The text doesn't wrap due to how PDF's are sized and so far after a bunch of Google searches I've yet to find a viable solution to get my PDF's converted into a readable Kindle format. Sometimes these books have code or pictures/tables in them, but most of the time they're text-heavy and to be honest I'd be surprised if there wasn't a free tool to handle the converting of PDF to one of the (seemingly many) Kindle formats. So, can anyone help me out with this? EDIT: I've tried Calibre, and have checked their forums to play with some of the advanced settings, yet the solutions available seem to be extremely poor, especially if the book you're attempting to read contains equations, code, or anything outside of plain text. I've also tried Amazon's conversion service, which wasn't much help with such documents. The best way I have found so far is to build the entire thing over again in ePub or RTF format and convert to MOBI from there. This works for text-heavy books with tables, but anything technical still isn't covered. Can anyone help with this?

  Read the article

• Wake-on-lan only works so many times

  - by Chance

  I have Wake-on-lan configured on my Windows XP machine so that the computer will wake up from Standby. Waking the computer from Standby via network traffic seems to work a certain number of times, say 4 or 5, then it stops working. If I restart the computer it seems to reset this behavior so that I can use WOL a few more times before it starts working. I use the command "wol" on my other, Linux machine with the appropriate IP address and MAC address of the card. I looked at the network card to see if it had different lights when WOL worked and when it didn't. When it has a solid amber light where the ethernet cable connects, WOL seems to work. When it has a flashing amber light, WOL does not. It seems that the system seems to almost "shut off" the card when it falls to sleep, but I don't know if this is a function of time or number of standby/wakeups. I have a 3Com 3c920 network card. If I look at the properties in Device Manager, I have "Allow this Device to bring the Computer out of Standby" checked. In the Advanced tab I have anything related to RWU (Remote Wake Up) enabled. I also believe I have the appropriate settings in BIOS related to Remote Wake-Up and I have tried both S1 and S3 power configurations in the BIOS. Intuitively, I would think I would uncheck "Allow the Computer to turn off this device to save power", but doing so disables the "Allow this Device to bring the Computer out of Standby" option. Does anyone know what is happening here or if there is a way to fix it? I have an integrated network card; would getting one that goes into a slot be better? I am running Windows XP on a Dell Optiplex GX240 with a 3Com 3c920 network card.

  Read the article

• UDP blocked by Windows XP Firewall when sending to local machine

  - by user36367

  Hi there, I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: - Windows XP Professional with Service Pack 3, all updated - Program that sends UDP datagrams - Program that receives UDP datagrams - Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas? Thanks in advance!

  Read the article

• SSH Keys Authentication keeps asking for password

  - by Rhyuk

  Im trying to set access from ServerA(SunOS) to ServerB(Some custom Linux with Keyboard Interactive login) with SSH Keys. As a proof of concept I was able to do it between 2 virtual machines. Now in my real life scenario it isnt working. I created the keys in ServerA, copied them to ServerB, chmod'd .ssh folders to 700 on both ServerA,B. Here is the log of what I get. debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: Peer sent proposed langtags, ctos: debug1: Peer sent proposed langtags, stoc: debug1: We proposed langtags, ctos: en-US debug1: We proposed langtags, stoc: en-US debug1: SSH2_MSG_KEX_DH_GEX_REQUEST sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: dh_gen_key: priv key bits set: 125/256 debug1: bits set: 1039/2048 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'XXX.XXX.XXX.XXX' is known and matches the RSA host key. debug1: Found key in /XXX/.ssh/known_hosts:1 debug1: bits set: 1061/2048 debug1: ssh_rsa_verify: signature correct debug1: newkeys: mode 1 debug1: set_newkeys: setting new keys for 'out' mode debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: newkeys: mode 0 debug1: set_newkeys: setting new keys for 'in' mode debug1: SSH2_MSG_NEWKEYS received debug1: done: ssh_kex2. debug1: send SSH2_MSG_SERVICE_REQUEST debug1: got SSH2_MSG_SERVICE_ACCEPT debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Next authentication method: publickey debug1: Trying private key: /XXXX/.ssh/identity debug1: Trying public key: /xxx/.ssh/id_rsa debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Trying private key: /xxx/.ssh/id_dsa debug1: Next authentication method: keyboard-interactive Password: Password: ServerB has pretty limited actions since its a custom propietary linux. What could be happening? EDIT WITH ANSWER: Problem was that I didnt have those settings enabled in the sshd_config (Refer to accepted answer) AND that while pasting the key from ServerA to ServerB it would interpret the key as 3 separate lines. What I did was, in case you cant use ssh-copy-id like I couldnt. Paste the first line of your key in your "ServerB" authorized_keys file WITHOUT the last 2 characters, then type yourself the missing characters from line 1 and the first one from line 2, this will prevent adding a "new line" between the first and second line of the key. Repeat with the 3d line.

  Read the article

• Netgear router is not resolving hostnames

  - by Thomas Clayson

  Not sure what the problem is, but I am used to being able to access other clients on my LAN via their hostname. We got a new router from plusnet (Netgear WNR1000v3) and now this has stopped working. For instance, if I were to run a web server from one computer with the hostname TomPC usually I could go into a browser and type http://TomPC and I would get the web server front page. I can access it by using the LAN ip of the machine. e.g. http://192.168.1.1 works fine. I thought it would be a simple option in the admin panel of the router - possibly I had to turn on DNS/DCHP or something. But I can't see anything, and my searches on the internet seem to turn up ridiculous solutions involving setting up a dedicated DNS server on my LAN. This is just a small home network - really I just want to be able to access my Raspberry PI on the network without having to work out the IP address every time. (I know I could just set a static IP address for it, but using its hostname would be much easier). DCHP is enabled in the LAN settings part, although RIP is disabled (I don't know what the latter is) I don't know if this has anything to do with it? Many thanks!

  Read the article

• Configuring a MySQL 5.1 Instance on Windows 7 Professional x64 Fails

  - by Thomas Owens

  I'm trying to set up my laptops to function as mobile development environments. Installing the software on my Linux machine and getting it configured was fairly straightforward, however I'm having trouble getting MySQL 5.1 Server installed and configured on Windows 7 Professional 64-bit. I'm currently using the Windows MSI Installer for the complete MySQL 5.1 system (as opposed to the Essentials installer also available). I've tried to install using both the 32-bit and 64-bit versions of MySQL 5.1 - the same events occur in both. I've installed both the Server Instance Configuration Wizard and Workbench and everything appears to be installed just fine. When I open the Instance Configuration Wizard, I select Detailed Configuration. On the next screen, I select Development Environment, then Multifunctional Database on the next screen. I leave the InnoDB settings unchanged. I select Manual Setting with 5 concurrent connections. I enable TCP/IP Networking on Port 3306 and Enable Strict Mode. I select the Standard Character Set. I check the boxes for Install as a Windows Service (and provide the name "MySQL") and Include the Bin Directory in Windows PATH. On the next screen, I set my root user name and password. I do not enable root access from remote machines and I also do not create an anonymous account. On the final screen of the wizard, when I click "Execute", the first two tasks (Prepare Configuration and Write Configuration File) complete. However, when it reaches Start Service, the wizard hangs and becomes unresponsive ("Not Responding" appears in the title bar and Task Manager). I would really like to be able to use both my Windows and Linux laptops as full-blown mobile development environments, but I can't do that without being able to run MySQL. Has anyone encountered this problem before? What options do I have to correct it?

  Read the article

• CloudFront with Custom Origin and ELB

  - by kmfk

  We are using CloudFront for our static assets but also wanted to allow for Gzip. We set up a new distribution with a custom origin pointing back to our application servers which are behind a elastic load balancer. We manually keep the files in sync across the cluster and update them when we publish. However, with this set up, we get nothing but Miss and RefreshHits from CloudFront, which so far has defeated the purpose. Is there any additional settings in order to use an ELB as your custom origin? In the docs, it references this as a viable solution. It appears when we point the distribution to a single server in our production cluster, cloudfront properly caches our assets. Is it possible that the sticky sessions cookie and the subsequent header that gets added by it could be an issue? Cache-Control: no-cache="set-cookie" //Added by load balancer Any ideas? FYI - currently, we have our custom origin pointing to a single EC2 instance, so caching is working correctly - in case you try to curl the file below. Example headers: curl -I http://static.quick-cdn.com/css/9850999.css HTTP/1.0 200 OK Accept-Ranges: bytes Cache-Control: max-age=3700 Cache-Control: no-cache="set-cookie" Content-Length: 23038 Content-Type: text/css Date: Thu, 12 Apr 2012 23:03:52 GMT Last-Modified: Thu, 12 Apr 2012 23:00:14 GMT Server: Apache/2.2.17 (Ubuntu) Vary: Accept-Encoding X-Cache: RefreshHit from cloudfront X-Amz-Cf-Id: K_q7Zy3_jdzlEJ85ukELVtdx1GmuXqApAbZZ7G0fPt0mxRMqPKX5pQ==,RzJmPku-rEIO9WlvuSoKa8hiAaR3dLk5KC4cQMWWrf_MDhmjWe8n6A== Via: 1.0 28c34f9fbf559a21ee16594849e4fc9c.cloudfront.net (CloudFront) Connection: close

  Read the article

• I get "An error occurred while Windows was synchronizing with [name of time server]." when trying t

  - by ChrisF

  Prompted by the answers to this question I decided to give the Windows built in time synchronisation another go. However, no matter what time server I use I get this error: "An error occurred while Windows was synchronizing with [name of time server]." The help suggests the following as reasons for failure: You are not connected to the Internet. Establish an Internet connection before you attempt to synchronize your clock. Your personal or network firewall prevents clock synchronization. Most corporate and organizational firewalls will block time synchronization, as do some personal firewalls. Home users should read the firewall documentation for information about unblocking network time protocol (NTP). You should be able to synchronize your clock if you switch to Windows Firewall. The Internet time server is too busy or is temporarily unavailable. If this is the case, try synchronizing your clock later, or update it manually by double-clicking the clock on the taskbar. You can also try using a different time server. The time shown on your computer is too different from the current time on the Internet time server. Internet time servers might not synchronize your clock if your computer's time is off by more than 15 hours. To synchronize the time properly, ensure that the date and time settings are set close to your current time in the Date and Time Properties in Control Panel. Now the first reason is clearly wrong - I am connected to the internet. I can see the 2nd being the most likely cause. I have Sygate Personal Firewall running, but it normally asks if something it trying to connect for the first time. Does anyone know I can unblock the NTP protocol - or at least check if it is blocked?. I don't think it's #3 or #4 as I've tried a number of different servers including the one currently used by Atomic Clock Sync. Though if someone knows the address of a UK time server I can double check this.

  Read the article

• Is there any way to customize the Windows 7 taskbar auto-hide behavior? Delay activation? Timer?

  - by calbar

  I'm becoming increasingly frustrated with the way Windows 7 handles showing a hidden taskbar. It's incredibly over-eager to pop out and obscure what I'm really trying to interact with, requiring me to move the mouse away, wait for it to auto-hide again, then resume what I was doing but more deliberately. After closely examining the behavior, it appears that a hidden taskbar "peeks out" from the edge by 2 or 3 pixels, and slowly moving your mouse into this area activates it; you don't even need to touch the edge of the screen. I would love it if there was a way to customize or change this behavior. Ideally, the taskbar would only pop out if you are actively "pushing" the edge of the screen it is hidden on. So activation only occurs once you've reached the screens edge and continue to move the mouse past a customizable threshold. Alternatively, a simple activation delay would suffice as well. So only if the mouse remains in that 2-3 pixel area (a.k.a. on the taskbar) for greater than a customizable amount of time does it pop out again. This would only be a fraction of a second. Often times the cursor simply "careens" off the edge of the screen while trying to focus on something nearby. Anyway, if there are any registry settings or utilities that can achieve either of these effects, that would be great! Thanks for your help.

  Read the article

• Port forwarding with multiple IP's

  - by Jon

  I work at a company which uses a Fortigate 60 router, something I'm not really familiar with. Everything worked fine with it until a week ago when Comcast came in and replaced our modem. It seemed as though the process went smoothly - our connection came back up and our static IP remained the same. However, none of our port forwarding is working. What has me confused is the Comcast modem apparently has two IP addresses. The WAN2 interface for it in the Fortigate router is set to 10.1.10.10. However, all of our port forwarding settings are set to an external IP address of 10.1.10.50. Now this setup used to work fine, so something with the Comcast modem must have changed. How can I find out what? I tried setting a computer to a local IP of 10.1.10.15 so I could open up the web interface for the modem, but I can't even ping 10.1.10.10 when I do that. Any ideas? Thanks!

  Read the article

• What is the main reason of adsl modem/routers dying ?

  - by ldigas

  The other day my home adsl modem/router (dwg 684t in this case) died. A guy from the telecom company came, brought another so no problem in day to day operation, but he also left this one. Now, I'm interested ... it didn't fall, it wasn't electrocuted ... but it just doesn't work. What could be the problem ? Can they be fixed ? Is it worth it (in which case I would have two which is always nice) ... What are the usual problems that occur with them ? In this case, I can connect to the router, I can see its settings, I just can't connect to the internet. With the new one everything works. Weird. Edit: Additional question: Can those things be fixed ? I mean, is it worth giving it to a local tinker for him to experiment on it ? I'm not looking for a definite opinion, just your personal advice ... (although in the end I think I'm gonna archive it in the "cylinder register")

  Read the article

< Previous Page | 490 491 492 493 494 495 496 497 498 499 500 501  | Next Page >