Search Results

Search found 32219 results on 1289 pages for 'screen size'.

Page 494/1289 | < Previous Page | 490 491 492 493 494 495 496 497 498 499 500 501  | Next Page >

• How do I stop and repair a RAID 5 array that has failed and has I/O pending?

  - by Ben Hymers

  The short version: I have a failed RAID 5 array which has a bunch of processes hung waiting on I/O operations on it; how can I recover from this? The long version: Yesterday I noticed Samba access was being very sporadic; accessing the server's shares from Windows would randomly lock up explorer completely after clicking on one or two directories. I assumed it was Windows being a pain and left it. Today the problem is the same, so I did a little digging; the first thing I noticed was that running ps aux | grep smbd gives a lot of lines like this: ben 969 0.0 0.2 96088 4128 ? D 18:21 0:00 smbd -F root 1708 0.0 0.2 93468 4748 ? Ss 18:44 0:00 smbd -F root 1711 0.0 0.0 93468 1364 ? S 18:44 0:00 smbd -F ben 3148 0.0 0.2 96052 4160 ? D Mar07 0:00 smbd -F ... There are a lot of processes stuck in the "D" state. Running ps aux | grep " D" shows up some other processes including my nightly backup script, all of which need to access the volume mounted on my RAID array at some point. After some googling, I found that it might be down to the RAID array failing, so I checked /proc/mdstat, which shows this: ben@jack:~$ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid5 sdb1[3](F) sdc1[1] sdd1[2] 2930271872 blocks level 5, 64k chunk, algorithm 2 [3/2] [_UU] unused devices: <none> And running mdadm --detail /dev/md0 gives this: ben@jack:~$ sudo mdadm --detail /dev/md0 /dev/md0: Version : 00.90 Creation Time : Sat Oct 31 20:53:10 2009 Raid Level : raid5 Array Size : 2930271872 (2794.53 GiB 3000.60 GB) Used Dev Size : 1465135936 (1397.26 GiB 1500.30 GB) Raid Devices : 3 Total Devices : 3 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Mon Mar 7 03:06:35 2011 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 1 Spare Devices : 0 Layout : left-symmetric Chunk Size : 64K UUID : f114711a:c770de54:c8276759:b34deaa0 Events : 0.208245 Number Major Minor RaidDevice State 3 8 17 0 faulty spare rebuilding /dev/sdb1 1 8 33 1 active sync /dev/sdc1 2 8 49 2 active sync /dev/sdd1 I believe this says that sdb1 has failed, and so the array is running with two drives out of three 'up'. Some advice I found said to check /var/log/messages for notices of failures, and sure enough there are plenty: ben@jack:~$ grep sdb /var/log/messages ... Mar 7 03:06:35 jack kernel: [4525155.384937] md/raid:md0: read error NOT corrected!! (sector 400644912 on sdb1). Mar 7 03:06:35 jack kernel: [4525155.389686] md/raid:md0: read error not correctable (sector 400644920 on sdb1). Mar 7 03:06:35 jack kernel: [4525155.389686] md/raid:md0: read error not correctable (sector 400644928 on sdb1). Mar 7 03:06:35 jack kernel: [4525155.389688] md/raid:md0: read error not correctable (sector 400644936 on sdb1). Mar 7 03:06:56 jack kernel: [4525176.231603] sd 0:0:1:0: [sdb] Unhandled sense code Mar 7 03:06:56 jack kernel: [4525176.231605] sd 0:0:1:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Mar 7 03:06:56 jack kernel: [4525176.231608] sd 0:0:1:0: [sdb] Sense Key : Medium Error [current] [descriptor] Mar 7 03:06:56 jack kernel: [4525176.231623] sd 0:0:1:0: [sdb] Add. Sense: Unrecovered read error - auto reallocate failed Mar 7 03:06:56 jack kernel: [4525176.231627] sd 0:0:1:0: [sdb] CDB: Read(10): 28 00 17 e1 5f bf 00 01 00 00 To me it is clear that device sdb has failed, and I need to stop the array, shutdown, replace it, reboot, then repair the array, bring it back up and mount the filesystem. I cannot hot-swap a replacement drive in, and don't want to leave the array running in a degraded state. I believe I am supposed to unmount the filesystem before stopping the array, but that is failing, and that is where I'm stuck now: ben@jack:~$ sudo umount /storage umount: /storage: device is busy. (In some cases useful info about processes that use the device is found by lsof(8) or fuser(1)) It is indeed busy; there are some 30 or 40 processes waiting on I/O. What should I do? Should I kill all these processes and try again? Is that a wise move when they are 'uninterruptable'? What would happen if I tried to reboot? Please let me know what you think I should do. And please ask if you need any extra information to diagnose the problem or to help!

  Read the article

• Useful software for netbook?

  - by Moayad Mardini

  I'm looking for recommendations of good software that are particularly useful for netbooks. Software that run great on small screens and low CPU/RAM requirments. I'll start off with the following : Operating Systems: Ubuntu Netbook Remix. Easy Peasy: A fork of Ubuntu Netbook Remix that was once called UBuntu EEE. It isn't just for eeePCs though. Definitely worth a look if vanilla Netbook Remix isn't cutting it. (MarkM) Damn Small Linux (Source) Windows 7: With trimming the installation or compressing the Windows directory to fit on an 8GB SSD. (Will Eddins) nLite: A utility to install a lightweight version of Windows XP without the unnecessary components (like Media Player, Internet Explorer, Outlook Express, MSN Explorer, Messenger...). Utilites: TouchFreeze: To disable the touch pad while typing (Source) InSSIDer: Not only does it make it easier to find and keep a wireless connection, but it turns a netbook into the perfect mobile tool for troubleshooting wireless networks. (phenry) AltMove: Adds more functionality to your mouse for interacting with windows. (Rob) ASUS Font Resizer Utility and other tools by ASUS, specific to ASUS Eee PC series. Internet: Run FileZilla FTP client for a small screen : You can hide a lot of FileZilla's interface parts in the View menu, even the directory trees. Go into Settings = Interface and move the message log next to the transfer queue, if you haven't hidden them both or you want to see them. Select a theme with 16x16 icons. (Source) IDEs and Text Editors: Best lightweight IDE/Text Editor: A question on Stack Overflow that has many good suggestions of IDEs and general text editors for programmers. What’s a good linux C/C++ IDE for a low-res screen?: IDEs for Linux-powered netbooks. Online tools: Dropbox: Since the Netbook has limited disk space, you would like to use Cloud Apps like Dropbox and Ubuntu One so that you don't run out of space especially if you are on a holiday. Later when you go back to your desktop with big hard disk,you can take out the files from your dropbox repo. (Manish Sinha) Google products: like Docs, Calendar and Reader (aviraldg) Web sites and software lists: Netbookfiles.com: Netbook specific software downloads. Software Apps to Maximise your Netbook Battery Power: Netbooks are known for their portability. Not only are they small and lightweight but with their increased power efficiency, batteries can last much longer than conventional laptops. This also means you no longer have to carry a power adapter with you! Several brands emphasis the longevity of the battery as a strong selling point, and for those people who travel a lot, it sure is. Free Must-Have Netbook Apps: Finding software for netbooks can present challenges due to limited hard drive space, processor power, RAM, and screen real-estate. That doesn't mean you have to do without essential programs. The apps below cover all the bases -- entertainment, productivity, security, and communication -- without compromising on performance or usability. Best of all, they're free! Useful Netbook Software: With short battery lives and small resolution screens Netbooks, unlike many other computers on the market, could so with some specific software for their use. Now, not all of those I’ve found are specifically designed for Netbooks, but all are relevant. And they’re designed for Windows XP. The question is community wiki, so feel free to edit it. Updated, thank you all for suggestions.

  Read the article

• sendmail can not relay from itself

  - by Bernie

  I am running 3 centos 5.2 servers and I have configured the server for forward all messages to root to be emailed to me via .forward rule. This is working fine on two of the servers but not on the third. I have also tried copying the mail config files from the backup server and placing them on the file server and restarting sendmail. I also removed and reinstalled sendmail via yum but the results are the same. I am not sure what the issue could be they are all standard centos installs. Here is an example from the backup server which is working and the fileserver which isn't I am also going to include the mail log. good from backup server [root@backup ]# sendmail -v [email protected] < test.mail [email protected]... Connecting to [127.0.0.1] via relay... 220 backup.localhost ESMTP Sendmail 8.13.8/8.13.8; Fri, 16 Oct 2009 10:23:50 -0700 >>> EHLO backup.localhost 250-backup.localhost Hello backup.localhost [127.0.0.1], pleased to meet you 250-ENHANCEDSTATUSCODES 250-PIPELINING 250-8BITMIME 250-SIZE 250-DSN 250-ETRN 250-DELIVERBY 250 HELP >>> MAIL From:<[email protected]> SIZE=73 250 2.1.0 <[email protected]>... Sender ok >>> RCPT To:<[email protected]> >>> DATA 250 2.1.5 <[email protected]>... Recipient ok 354 Enter mail, end with "." on a line by itself >>> . 250 2.0.0 n9GHNoGC020924 Message accepted for delivery [email protected]... Sent (n9GHNoGC020924 Message accepted for delivery) Closing connection to [127.0.0.1] >>> QUIT 221 2.0.0 backup.localhost closing connection bad from file server [root@fileserver bernie]# sendmail -v [email protected] < test.mail [email protected]... Connecting to [127.0.0.1] via relay... 220 fileserver.localhost ESMTP Sendmail 8.13.8/8.13.8; Fri, 16 Oct 2009 10:23:26 -0700 >>> EHLO fileserver.localhost 250-fileserver.localhost Hello fileserver.localhost [127.0.0.1], pleased to meet you 250 ENHANCEDSTATUSCODES >>> MAIL From:<[email protected]> 550 5.0.0 Access denied root... Using cached ESMTP connection to [127.0.0.1] via relay... >>> RSET 250 2.0.0 Reset state >>> MAIL From:<> 550 5.0.0 Access denied postmaster... Using cached ESMTP connection to [127.0.0.1] via relay... >>> RSET 250 2.0.0 Reset state >>> MAIL From:<> 550 5.0.0 Access denied Closing connection to [127.0.0.1] >>> QUIT 221 2.0.0 fileserver.localhost closing connection mail log Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDom028059: from=root, size=72, class=0, nrcpts=1, msgid=<[email protected]>, relay=root@localhost Oct 16 10:39:13 fileserver sendmail[28060]: n9GHdDwl028060: tcpwrappers (fileserver.localhost, 127.0.0.1) rejection Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDom028059: [email protected], ctladdr=root (0/0), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30072, relay=[127.0.0.1] [127.0.0.1], dsn=5.0.0, stat=Service unavailable Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDom028059: n9GHdDon028059: DSN: Service unavailable Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDon028059: to=root, delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=31096, relay=[127.0.0.1], dsn=5.0.0, stat=Service unavailable Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDon028059: n9GHdDoo028059: return to sender: Service unavailable Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDoo028059: to=postmaster, delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=32120, relay=[127.0.0.1], dsn=5.0.0, stat=Service unavailable Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDon028059: Losing ./qfn9GHdDon028059: savemail panic Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDon028059: SYSERR(root): savemail: cannot save rejected email anywhere

  Read the article

• Splitting a raidctl mirror safely

  - by milkfilk

  I have a Sun T5220 server with the onboard LSI card and two disks that were in a RAID 1 mirror. The data is not important right now but we had a failed disk and are trying to understand how to do this for real if we had to recover from a failure. The initial situation looked like this: # raidctl -l c1t0d0 Volume Size Stripe Status Cache RAID Sub Size Level Disk ---------------------------------------------------------------- c1t0d0 136.6G N/A DEGRADED OFF RAID1 0.1.0 136.6G GOOD N/A 136.6G FAILED Green light on the 0.0.0 disk. Find / lights up the 0.1.0 disk. So I know I have a bad drive and which one it is. Server still boots obviously. First, we tried putting a new disk in. This disk came from an unknown source. Format would not see it, cfgadm -al would not see it so raidctl -l would not see it. I figure it's bad. We tried another disk from another spare server: # raidctl -c c1t1d0 c1t0d0 (where t1 is my good disk - 0.1.0) Disk has occupied space. Also the different syntax options don't change anything: # raidctl -C "0.1.0 0.0.0" -r 1 1 Disk has occupied space. # raidctl -C "0.1.0 0.0.0" 1 Disk has occupied space. Ok. Maybe this is because the disk from the spare server had a RAID 1 on it already. Aha, I can see another volume in raidctl: # raidctl -l Controller: 1 Volume:c1t1d0 (this is my server's root mirror) Volume:c1t132d0 (this is the foreign root mirror) Disk: 0.0.0 Disk: 0.1.0 ... No problem. I don't care about the data, I'll just delete the foreign mirror. # raidctl -d c1t132d0 (warning about data deletion but it works) At this point, /usr/bin/ binaries freak out. By that I mean, ls -l /usr/bin/which shows 1.4k but cat /usr/bin/which gives me a newline. Great, I just blew away the binaries (ie: binaries in mem still work)? I bounce the box. It all comes back fine. WTF. Anyway, back to recreating my mirror. # raidctl -l Controller: 1 Volume:c1t1d0 (this is my server's root mirror) Disk: 0.0.0 Disk: 0.1.0 ... Man says that you can delete a mirror and it will split it. Ok, I'll delete the root mirror. # raidctl -d c1t0d0 Array in use. (this might not be the exact error) I googled this and found of course you can't do this (even with -f) while booted off the mirror. Ok. I boot cdrom -s and deleted the volume. Now I have one disk that has a type of "LSI-Logical-Volume" on c1t1d0 (where my data is) and a brand new "Hitachi 146GB" on c1t0d0 (what I'm trying to mirror to): (booted off the CD) # raidctl -c c1t1d0 c1t0d0 (man says it's source destination for mirroring) Illegal Array Layout. # raidctl -C "0.1.0 0.0.0" -r 1 1 (alt syntax per man) Illegal Array Layout. # raidctl -C "0.1.0 0.0.0" 1 (assumes raid1, no help) Illegal Array Layout. Same size disks, same manufacturer but I did delete the volume instead of throwing in a blank disk and waiting for it to resync. Maybe this was a critical error. I tried selecting the type in format for my good disk to be a plain 146gb disk but it resets the partition table which I'm pretty sure would wipe the data (bad if this was production). Am I boned? Anyone have experience with breaking and resyncing a mirror? There's nothing on Google about "Illegal Array Layout" so here's my contrib to the search gods.

  Read the article

• Squid w/ SquidGuard fails w/ "Too few redirector processes are running"

  - by DKNUCKLES

  I'm trying to implement a Squid proxy in a quick and easy fashion and I'm receiving some errors I have been unable to resolve. The box is a pre-made appliance, however it seems to fail on launch.The following is the cache.log file when I attempt to launch the squid service. 2012/11/18 22:14:29| Starting Squid Cache version 3.0.STABLE20-20091201 for i686 -pc-linux-gnu... 2012/11/18 22:14:29| Process ID 12647 2012/11/18 22:14:29| With 1024 file descriptors available 2012/11/18 22:14:29| Performing DNS Tests... 2012/11/18 22:14:29| Successful DNS name lookup tests... 2012/11/18 22:14:29| DNS Socket created at 0.0.0.0, port 40513, FD 8 2012/11/18 22:14:29| Adding nameserver 192.168.0.78 from /etc/resolv.conf 2012/11/18 22:14:29| Adding nameserver 8.8.8.8 from /etc/resolv.conf 2012/11/18 22:14:29| helperOpenServers: Starting 5/5 'bin' processes 2012/11/18 22:14:29| ipcCreate: /opt/squidguard/bin: (13) Permission denied 2012/11/18 22:14:29| ipcCreate: /opt/squidguard/bin: (13) Permission denied 2012/11/18 22:14:29| ipcCreate: /opt/squidguard/bin: (13) Permission denied 2012/11/18 22:14:29| ipcCreate: /opt/squidguard/bin: (13) Permission denied 2012/11/18 22:14:29| ipcCreate: /opt/squidguard/bin: (13) Permission denied 2012/11/18 22:14:29| helperOpenServers: Starting 5/5 'squid-auth.pl' processes 2012/11/18 22:14:29| User-Agent logging is disabled. 2012/11/18 22:14:29| Referer logging is disabled. 2012/11/18 22:14:29| Unlinkd pipe opened on FD 23 2012/11/18 22:14:29| Swap maxSize 10240000 + 8192 KB, estimated 788322 objects 2012/11/18 22:14:29| Target number of buckets: 39416 2012/11/18 22:14:29| Using 65536 Store buckets 2012/11/18 22:14:29| Max Mem size: 8192 KB 2012/11/18 22:14:29| Max Swap size: 10240000 KB 2012/11/18 22:14:29| Version 1 of swap file with LFS support detected... 2012/11/18 22:14:29| Rebuilding storage in /opt/squid3/var/cache (DIRTY) 2012/11/18 22:14:29| Using Least Load store dir selection 2012/11/18 22:14:29| Set Current Directory to /opt/squid3/var/cache 2012/11/18 22:14:29| Loaded Icons. 2012/11/18 22:14:29| Accepting HTTP connections at 10.0.0.6, port 3128, FD 25. 2012/11/18 22:14:29| Accepting ICP messages at 0.0.0.0, port 3130, FD 26. 2012/11/18 22:14:29| HTCP Disabled. 2012/11/18 22:14:29| Ready to serve requests. 2012/11/18 22:14:29| Done reading /opt/squid3/var/cache swaplog (0 entries) 2012/11/18 22:14:29| Finished rebuilding storage from disk. 2012/11/18 22:14:29| 0 Entries scanned 2012/11/18 22:14:29| 0 Invalid entries. 2012/11/18 22:14:29| 0 With invalid flags. 2012/11/18 22:14:29| 0 Objects loaded. 2012/11/18 22:14:29| 0 Objects expired. 2012/11/18 22:14:29| 0 Objects cancelled. 2012/11/18 22:14:29| 0 Duplicate URLs purged. 2012/11/18 22:14:29| 0 Swapfile clashes avoided. 2012/11/18 22:14:29| Took 0.02 seconds ( 0.00 objects/sec). 2012/11/18 22:14:29| Beginning Validation Procedure 2012/11/18 22:14:29| WARNING: redirector #1 (FD 9) exited 2012/11/18 22:14:29| WARNING: redirector #2 (FD 10) exited 2012/11/18 22:14:29| WARNING: redirector #3 (FD 11) exited 2012/11/18 22:14:29| WARNING: redirector #4 (FD 12) exited 2012/11/18 22:14:29| Too few redirector processes are running FATAL: The redirector helpers are crashing too rapidly, need help! Squid Cache (Version 3.0.STABLE20-20091201): Terminated abnormally. CPU Usage: 0.112 seconds = 0.032 user + 0.080 sys Maximum Resident Size: 0 KB Page faults with physical i/o: 0 Memory usage for squid via mallinfo(): total space in arena: 2944 KB Ordinary blocks: 2857 KB 6 blks Small blocks: 0 KB 0 blks Holding blocks: 1772 KB 8 blks Free Small blocks: 0 KB Free Ordinary blocks: 86 KB Total in use: 4629 KB 157% Total free: 86 KB 3% The "permission denied" area is where I have been focusing my attention with no luck. The following is what I've tried. Chmod'ing the /opt/squidguard/bin folder to 777 Changing the user that squidguard runs under to root / nobody / www-data / squid3 Tried changing ownership of the /opt/squidguard/bin folder to all names listed above after assigning that user to run with squid. Any help with this would be greatly appreciated.

  Read the article

• xrandr shows two displays (LVDS1), but how can I use VGA1 only?

  - by Tom Fishman

  We're running Ubuntu 11 on this hardware: Foxconn R20-D2 Intel Atom D510 Intel NM10 Intel GMA 3150 Barebone There is no integrated display (it is a barebone box). I connected an external VGA to it. However xrandr shows two displays: Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096 LVDS1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.0*+ 800x600 60.3 56.2 640x480 59.9 VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 519mm x 324mm 1920x1200 60.0 + 1600x1200 60.0 1680x1050 60.0 1280x1024 76.0 75.0 72.0 60.0 1440x900 75.0 59.9 1152x864 75.0 1024x768 75.1 70.1 60.0* 832x624 74.6 800x600 72.2 75.0 60.3 640x480 72.8 75.0 66.7 60.0 720x400 70.1 But I don't have two displays. How can I get rid of LVDS1 and use only VGA1? The direct result is that I'm seeing a 1024x768 resolution on my VGA display, because the OS is using "mirror" mode which uses the lower resolution of the two. Turning off the mirror is not a solution. I want to fix it. Related logs: ... [ 20.019] (II) intel(0): Creating default Display subsection in Screen section "Default Screen Section" for depth/fbbpp 24/32 [ 20.019] (==) intel(0): Depth 24, (--) framebuffer bpp 32 [ 20.019] (==) intel(0): RGB weight 888 [ 20.019] (==) intel(0): Default visual is TrueColor [ 20.019] (II) intel(0): Integrated Graphics Chipset: Intel(R) Pineview G [ 20.019] (--) intel(0): Chipset: "Pineview G" [ 20.019] (**) intel(0): Relaxed fencing enabled [ 20.019] (**) intel(0): Wait on SwapBuffers? enabled [ 20.019] (**) intel(0): Triple buffering? enabled [ 20.019] (**) intel(0): Framebuffer tiled [ 20.019] (**) intel(0): Pixmaps tiled [ 20.020] (**) intel(0): 3D buffers tiled [ 20.020] (**) intel(0): SwapBuffers wait enabled [ 20.020] (==) intel(0): video overlay key set to 0x101fe [ 20.020] (II) intel(0): Output LVDS1 has no monitor section [ 20.020] (II) intel(0): found backlight control interface /sys/class/backlight/intel_backlight [ 20.080] (II) intel(0): Output VGA1 has no monitor section [ 20.080] (II) intel(0): EDID for output LVDS1 [ 20.081] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported) [ 20.081] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported) [ 20.081] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported) [ 20.081] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported) ... [ 20.082] (II) intel(0): Not using default mode "960x600" (doublescan mode not supported) [ 20.082] (II) intel(0): Printing probed modes for output LVDS1 [ 20.082] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz) [ 20.082] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz) [ 20.082] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz) [ 20.082] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz) [ 20.149] (II) intel(0): EDID for output VGA1 [ 20.149] (II) intel(0): Manufacturer: BNQ Model: 771b Serial#: 6595 [ 20.149] (II) intel(0): Year: 2008 Week: 16 [ 20.149] (II) intel(0): EDID Version: 1.3 [ 20.149] (II) intel(0): Analog Display Input, Input Voltage Level: 0.700/0.700 V ... [ 20.152] (II) intel(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz) [ 20.152] (II) intel(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz) [ 20.152] (II) intel(0): Output LVDS1 connected [ 20.152] (II) intel(0): Output VGA1 connected [ 20.152] (II) intel(0): Using exact sizes for initial modes [ 20.152] (II) intel(0): Output LVDS1 using initial mode 1024x768 [ 20.152] (II) intel(0): Output VGA1 using initial mode 1024x768 [ 20.152] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated. ...

  Read the article

• broadcom 5722 NIC not installed on Ubuntu Server, although driver present

  - by Bastien

  Hello, I just installed Ubuntu Server 10.04 LTS, running kernel 2.6.32-24-server, on a brand new Dell T110 server, supposedly fully compatible with Ubuntu Server. I have two NICs: one ONBOARD, the other additional on PCI. both of them are Broadcom netXtreme 5572. on the first boot of the system, I could see both cards as eth0 and eth1 (with ifconfig) I configured eth0 as static IP (as planned), and did not configure eth1. after rebooting, one of the two NICs "disappeared": it does not appear in ifconfig at all. the one that disappeared is the ONBOARD one. I investigated a bit and found the following things: the card is SEEN, but not "installed", it appears as "UNCLAIMED" in lshw: *-network UNCLAIMED description: Ethernet controller product: NetXtreme BCM5722 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress cap_list configuration: latency=0 resources: memory:df9f0000-df9fffff *-network description: Ethernet interface product: NetXtreme BCM5722 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 00 serial: 00:10:18:60:23:64 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.102 duplex=full firmware=5722-v3.09 ip=10.129.167.25 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:35 memory:dfaf0000-dfafffff so I checked my dmesg and found a few strange lines, showing, there actually is a problem bringing up this card: [ 3.737506] tg3: Could not obtain valid ethernet address, aborting. [ 3.737527] tg3 0000:04:00.0: PCI INT A disabled [ 3.737535] tg3: probe of 0000:04:00.0 failed with error -22 [ 3.737553] alloc irq_desc for 17 on node -1 [ 3.737555] alloc kstat_irqs on node -1 [ 3.737560] tg3 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 3.737566] tg3 0000:05:00.0: setting latency timer to 64 [ 3.793529] eth0: Tigon3 [partno(BCM95722A2202G) rev a200] (PCI Express) MAC address 00:10:18:60:23:64 [ 3.793532] eth0: attached PHY is 5722/5756 (10/100/1000Base-T Ethernet) (WireSpeed[1]) [ 3.793534] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 3.793536] eth0: dma_rwctrl[76180000] dma_mask[64-bit] that actually shows that one NIC is recognized, the other is not. I researched a bit more, with lspci -v: 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Flags: fast devsel, IRQ 16 Memory at df9f0000 (64-bit, non-prefetchable) [size=64K] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data <?> Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 00-00-00-fe-ff-00-00-00 Kernel modules: tg3 05:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Flags: bus master, fast devsel, latency 0, IRQ 35 Memory at dfaf0000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data <?> Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 64-23-60-fe-ff-18-10-00 Capabilities: [16c] Power Budgeting <?> Kernel driver in use: tg3 Kernel modules: tg3 here I could see that the MAC address is 00-00-00-FE-FF-00-00-00, which, according to some forum posts on several websites, could be an issue. I've researched everything I could on the net, and found out several people having slightly comparable issues, but they usually involve different HW, and do not provide a proper explanation / solution... I would appreciate if anyone around here has some info to share ! thanks

  Read the article

• Where's the Swap File/Partition?

  - by chrisbunney

  I'm investigating the virtual memory configuration of a Debian based Amazon EC2 instance, and as my background isn't in system admin, I'm slightly confused by what I'm seeing. We're using MongoDB, and the monitoring server we have indicates that the Mongo process is using about 20GB of swap space, however I can't figure out where this is located on the server. As far as I can tell from using the various suggested methods from Google, there is either a much smaller amount, or none at all. top indicates that there is 1.8GB of swap memory: top - 15:35:21 up 6 days, 3:23, 1 user, load average: 1.60, 1.43, 1.37 Tasks: 47 total, 2 running, 45 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 1.3%sy, 0.0%ni, 14.7%id, 83.8%wa, 0.0%hi, 0.0%si, 0.1%st Mem: 3928924k total, 2855572k used, 1073352k free, 640564k buffers Swap: 0k total, 0k used, 0k free, 1887788k cached swapon -s doesn't seem to think there's any swap space: Filename Type Size Used Priority free -m doesn't think there's any swap either: total used free shared buffers cached Mem: 3836 3663 172 0 626 2701 -/+ buffers/cache: 336 3500 Swap: 0 0 0 And neither does vmstat: procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 3 0 66224 641372 2874744 0 0 21 5012 21 33 2 2 76 19 But cat /etc/fstab thinks there is a swap partition: /dev/xvda1 / ext3 defaults 1 1 /dev/xvda2 /mnt ext3 defaults 0 0 /dev/xvda3 swap swap defaults 0 0 none /proc proc defaults 0 0 none /sys sysfs defaults 0 0 However df -k gives no indication of the xvda3 partition: Filesystem 1K-blocks Used Available Use% Mounted on /dev/xvda1 16513960 15675324 0 100% / tmpfs 1964460 8 1964452 1% /lib/init/rw udev 1914148 28 1914120 1% /dev tmpfs 1964460 4 1964456 1% /dev/shm So I really don't know what to make of this, because I appear to have a process using about 10 times more virtual memory than what might be available, and I have no idea where this virtual memory is on the system. I'm probably misinterpreting the output of the tools, so I'd be grateful if someone would be able to set me straight: What have I got wrong, what's the right interpretation, and how do you reach that interpretation? EDIT0: We use 10gen's MMS for monitoring the database, the relevant section for memory from the last data point is: "mem": { "virtual": 20749, "bits": 64, "supported": true, "mappedWithJournal": 20376, "mapped": 10188, "resident": 1219 }, This JSON is specific to the database process (I believe) rather than the system as a whole. fdisk -l /dev/xvda outputs... nothing? I tried each of the 3 xvda entries in /etc/fstab as well: root@ip:~# fdisk -l /dev/xvda1 Disk /dev/xvda1: 34.4 GB, 34359738368 bytes 255 heads, 63 sectors/track, 4177 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/xvda1 doesn't contain a valid partition table root@ip:~# fdisk -l /dev/xvda2 root@ip:~# fdisk -l /dev/xvda3 root@ip:~# Edit1: Output of cat /proc/meminfo for the sake of completeness: MemTotal: 3928924 kB MemFree: 726600 kB Buffers: 648368 kB Cached: 2216556 kB SwapCached: 0 kB Active: 1945100 kB Inactive: 994016 kB Active(anon): 60476 kB Inactive(anon): 12952 kB Active(file): 1884624 kB Inactive(file): 981064 kB Unevictable: 0 kB Mlocked: 0 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 387180 kB Writeback: 0 kB AnonPages: 73380 kB Mapped: 1188260 kB Shmem: 48 kB Slab: 149768 kB SReclaimable: 146076 kB SUnreclaim: 3692 kB KernelStack: 1104 kB PageTables: 16096 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 1964460 kB Committed_AS: 305572 kB VmallocTotal: 34359738367 kB VmallocUsed: 16760 kB VmallocChunk: 34359721448 kB HardwareCorrupted: 0 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 3932160 kB DirectMap2M: 0 kB

  Read the article

• Do I need to be worried about these SMART drive temperatures?

  - by Steve Lorimer

  I have 5 hard drives in a machine sitting in a cupboard. /dev/sda is a 500GB Seagate drive, and is the boot disk. /dev/sd{b,c,d,e} are 2TB drives in a raid6 configuration. smartctl is showing significantly higher temperatures (like ~140 degrees celsius) on the raid drives than the boot drive. Do I need to be worried? /dev/sdb and /dev/sde are new Western Digital Black drives (new=1 week) /dev/sdc and /dev/sdd are 5 year old Hitachi drives /dev/sda [SAT], Temperature_Celsius changed from 40 to 39 /dev/sdc [SAT], Temperature_Celsius changed from 142 to 146 /dev/sdc [SAT], Temperature_Celsius changed from 146 to 142 /dev/sdd [SAT], Temperature_Celsius changed from 142 to 146 /dev/sda [SAT], Airflow_Temperature_Cel changed from 61 to 62 /dev/sda [SAT], Temperature_Celsius changed from 39 to 38 /dev/sde [SAT], Temperature_Celsius changed from 107 to 108 /dev/sdb [SAT], Temperature_Celsius changed from 108 to 109 /dev/sdc [SAT], Temperature_Celsius changed from 146 to 150 /dev/sdc [SAT], Temperature_Celsius changed from 146 to 150 /dev/sda [SAT], Airflow_Temperature_Cel changed from 62 to 61 /dev/sda [SAT], Temperature_Celsius changed from 38 to 39 Update: Adding detailed drive information as per request: /dev/sda =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Pipeline HD 5900.2 Device Model: ST3500312CS Serial Number: 5VV47HXA LU WWN Device Id: 5 000c50 02aad5ad6 Firmware Version: SC13 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5900 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 1.5 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sdb =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD2003FZEX-00Z4SA0 Serial Number: WD-WMC1F1398726 LU WWN Device Id: 5 0014ee 003b8bd25 Firmware Version: 01.01A01 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sdc =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723020BLA642 Serial Number: MN1220F30WSTUD LU WWN Device Id: 5 000cca 369cc9f5d Firmware Version: MN6OA580 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sdd =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723020BLA642 Serial Number: MN1220F30WST4D LU WWN Device Id: 5 000cca 369cc9f48 Firmware Version: MN6OA580 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sde =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD2003FZEX-00Z4SA0 Serial Number: WD-WMC1F1483782 LU WWN Device Id: 5 0014ee 3002d235c Firmware Version: 01.01A01 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled

  Read the article

• Courier Maildrop error user unknown. Command output: Invalid user specified

  - by cad

  Hello I have a problem with maildrop. I have read dozens of webs/howto/emails but couldnt solve it. My objective is moving automatically spam messages to a spam folder. My email server is working perfectly. It marks spam in subject and headers using spamassasin. My box has: Ubuntu 9.04 Web: Apache2 + Php5 + MySQL MTA: Postfix 2.5.5 + SpamAssasin + virtual users using mysql IMAP: Courier 0.61.2 + Courier AuthLib WebMail: SquirrelMail I have read that I could use Squirrelmail directly (not a good idea), procmail or maildrop. As I already have maildrop in the box (from courier) I have configured the server to use maildrop (added an entry in transport table for a virtual domain). I found this error in email: This is the mail system at host foo.net I'm sorry to have to inform you that your message could not be delivered to one or more recipients. It's attached below. For further assistance, please send mail to postmaster. If you do so, please include this problem report. You can delete your own text from the attached returned message. The mail system <[email protected]>: user unknown. Command output: Invalid user specified. Final-Recipient: rfc822; [email protected] Action: failed Status: 5.1.1 Diagnostic-Code: x-unix; Invalid user specified. ---------- Forwarded message ---------- From: test <[email protected]> To: [email protected] Date: Sat, 1 May 2010 19:49:57 +0100 Subject: fail fail An this in the logs May 1 18:50:18 foo.net postfix/smtpd[14638]: connect from mail-bw0-f212.google.com[209.85.218.212] May 1 18:50:19 foo.net postfix/smtpd[14638]: 8A9E9DC23F: client=mail-bw0-f212.google.com[209.85.218.212] May 1 18:50:19 foo.net postfix/cleanup[14643]: 8A9E9DC23F: message-id=<[email protected]> May 1 18:50:19 foo.net postfix/qmgr[14628]: 8A9E9DC23F: from=<[email protected]>, size=1858, nrcpt=1 (queue active) May 1 18:50:23 foo.net postfix/pickup[14627]: 1D4B4DC2AA: uid=5002 from=<[email protected]> May 1 18:50:23 foo.net postfix/cleanup[14643]: 1D4B4DC2AA: message-id=<[email protected]> May 1 18:50:23 foo.net postfix/pipe[14644]: 8A9E9DC23F: to=<[email protected]>, relay=spamassassin, delay=3.8, delays=0.55/0.02/0/3.2, dsn=2.0.0, status=sent (delivered via spamassassin service) May 1 18:50:23 foo.net postfix/qmgr[14628]: 8A9E9DC23F: removed May 1 18:50:23 foo.net postfix/qmgr[14628]: 1D4B4DC2AA: from=<[email protected]>, size=2173, nrcpt=1 (queue active) **May 1 18:50:23 foo.netpostfix/pipe[14648]: 1D4B4DC2AA: to=<[email protected]>, relay=maildrop, delay=0.22, delays=0.06/0.01/0/0.15, dsn=5.1.1, status=bounced (user unknown. Command output: Invalid user specified. )** May 1 18:50:23 foo.net postfix/cleanup[14643]: 4C2BFDC240: message-id=<[email protected]> May 1 18:50:23 foo.net postfix/qmgr[14628]: 4C2BFDC240: from=<>, size=3822, nrcpt=1 (queue active) May 1 18:50:23 foo.net postfix/bounce[14651]: 1D4B4DC2AA: sender non-delivery notification: 4C2BFDC240 May 1 18:50:23 foo.net postfix/qmgr[14628]: 1D4B4DC2AA: removed May 1 18:50:24 foo.net postfix/smtp[14653]: 4C2BFDC240: to=<[email protected]>, relay=gmail-smtp-in.l.google.com[209.85.211.97]:25, delay=0.91, delays=0.02/0.03/0.12/0.74, dsn=2.0.0, status=sent (250 2.0.0 OK 1272739824 37si5422420ywh.59) May 1 18:50:24 foo.net postfix/qmgr[14628]: 4C2BFDC240: removed My config files: http://lar3d.net/main.cf (/etc/postfix) http://lar3d.net/master.c (/etc/postfix) http://lar3d.net/local.cf (/etc/spamassasin) http://lar3d.net/maildroprc (maildroprc) If I change master.cf line (as suggested here) maildrop unix - n n - - pipe flags=DRhu user=vmail argv=/usr/lib/courier/bin/maildrop -d ${recipient} with maildrop unix - n n - - pipe flags=DRhu user=vmail argv=/usr/lib/courier/bin/maildrop -d vmail ${recipient} I get the email in /home/vmail/MailDir instead of the correct dir (/home/vmail/foo.net/info/.SPAM ) After reading a lot I have some guess but not sure. - Maybe I have to install userdb? - Maybe is something related with mysql, but everything is working ok - If I try with procmail I will face same problem... - What are flags DRhu for? Couldnt find doc about them - In some places I found maildrop line with more parameters flags=DRhu user=vmail argv=/usr/lib/courier/bin/maildrop -d $ ${recipient} ${extension} ${recipient} ${user} ${nexthop} ${sender} I am really lost. Dont know how to continue. If you have any idea or need another config file please let me know. Thanks!!!

  Read the article

• How do you re-mount an ext3 fs readwrite after it gets mounted readonly from a disk error?

  - by cagenut

  Its a relatively common problem when something goes wrong in a SAN for ext3 to detect the disk write errors and remount the filesystem read-only. Thats all well and good, only when the SAN is fixed I can't figure out how to re-re-mount the filesystem read-write without rebooting. Behold: [root@localhost ~]# multipath -ll mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=1 queue_if_no_path][hwhandler=0][rw] \_ round-robin 0 [prio=2][active] \_ 1:0:0:1 sdb 8:16 [active][ready] \_ 2:0:0:1 sdc 8:32 [active][ready] [root@localhost ~]# mount /dev/mapper/mpath0 /mnt/foo [root@localhost ~]# touch /mnt/foo/blah All good, now I yank the LUN out from under it. [root@localhost ~]# touch /mnt/foo/blah [root@localhost ~]# touch /mnt/foo/blah touch: cannot touch `/mnt/foo/blah': Read-only file system [root@localhost ~]# tail /var/log/messages Mar 18 13:17:33 localhost multipathd: sdb: tur checker reports path is down Mar 18 13:17:34 localhost multipathd: sdc: tur checker reports path is down Mar 18 13:17:35 localhost kernel: Aborting journal on device dm-2. Mar 18 13:17:35 localhost kernel: Buffer I/O error on device dm-2, logical block 1545 Mar 18 13:17:35 localhost kernel: lost page write due to I/O error on dm-2 Mar 18 13:17:36 localhost kernel: ext3_abort called. Mar 18 13:17:36 localhost kernel: EXT3-fs error (device dm-2): ext3_journal_start_sb: Detected aborted journal Mar 18 13:17:36 localhost kernel: Remounting filesystem read-only It only thinks its read-only, in reality its not even there. [root@localhost ~]# multipath -ll sdb: checker msg is "tur checker reports path is down" sdc: checker msg is "tur checker reports path is down" mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=0][hwhandler=0][rw] \_ round-robin 0 [prio=0][enabled] \_ 1:0:0:1 sdb 8:16 [failed][faulty] \_ 2:0:0:1 sdc 8:32 [failed][faulty] [root@localhost ~]# ll /mnt/foo/ ls: reading directory /mnt/foo/: Input/output error total 20 -rw-r--r-- 1 root root 0 Mar 18 13:11 bar How it still remembers that 'bar' file being there... mystery, but not important right now. Now I re-present the LUN: [root@localhost ~]# tail /var/log/messages Mar 18 13:23:58 localhost multipathd: sdb: tur checker reports path is up Mar 18 13:23:58 localhost multipathd: 8:16: reinstated Mar 18 13:23:58 localhost multipathd: mpath0: queue_if_no_path enabled Mar 18 13:23:58 localhost multipathd: mpath0: Recovered to normal mode Mar 18 13:23:58 localhost multipathd: mpath0: remaining active paths: 1 Mar 18 13:23:58 localhost multipathd: dm-2: add map (uevent) Mar 18 13:23:58 localhost multipathd: dm-2: devmap already registered Mar 18 13:23:59 localhost multipathd: sdc: tur checker reports path is up Mar 18 13:23:59 localhost multipathd: 8:32: reinstated Mar 18 13:23:59 localhost multipathd: mpath0: remaining active paths: 2 Mar 18 13:23:59 localhost multipathd: dm-2: add map (uevent) Mar 18 13:23:59 localhost multipathd: dm-2: devmap already registered [root@localhost ~]# multipath -ll mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=1 queue_if_no_path][hwhandler=0][rw] \_ round-robin 0 [prio=2][enabled] \_ 1:0:0:1 sdb 8:16 [active][ready] \_ 2:0:0:1 sdc 8:32 [active][ready] Great right? It says [rw] right there. Not so fast: [root@localhost ~]# touch /mnt/foo/blah touch: cannot touch `/mnt/foo/blah': Read-only file system OK, doesn't do it automatically, I'll just give it a little push: [root@localhost ~]# mount -o remount /mnt/foo mount: block device /dev/mapper/mpath0 is write-protected, mounting read-only Noooooooooo. I have tried all sorts of different mount/tune2fs/dmsetup commands and I cannot figure out how to get it to un-flag the block device as write-protected. Rebooting will fix it, but I'd much rather do it on-line. An hour of googling has gotten me nowhere either. Save me ServerFault.

  Read the article

• Cannot Start MySQL Server on Fresh MAMP Install

  - by alexpelan

  I'm using Mac OS X 10.6.2 on my Macbook Pro. I can get the apache server to start, but not the mysql server, on both the default apache and default MAMP ports. When I try to go to my start page, I get the message "Error: Could not connect to MySQL server!" . Here's what's in my mysql error log: 00513 02:00:07 mysqld_safe mysqld from pid file /Applications/MAMP/tmp/mysql/mysql.pid ended 100513 02:00:16 mysqld_safe Starting mysqld daemon with databases from /Applications/MAMP/db/mysql 100513 2:00:16 [Warning] The syntax '--log_slow_queries' is deprecated and will be removed in a future release. Please use '--slow_query_log'/'--slow_query_log_file' instead. 100513 2:00:16 [Warning] You have forced lower_case_table_names to 0 through a command-line option, even though your file system '/Applications/MAMP/db/mysql/' is case insensitive. This means that you can corrupt a MyISAM table by accessing it with different cases. You should consider changing lower_case_table_names to 1 or 2 100513 2:00:16 [Warning] One can only use the --user switch if running as root 100513 2:00:16 [Note] Plugin 'FEDERATED' is disabled. 100513 2:00:16 [Note] Plugin 'ndbcluster' is disabled. InnoDB: Error: log file /usr/local/mysql/data/ib_logfile0 is of different size 0 5242880 bytes InnoDB: than specified in the .cnf file 0 16777216 bytes! 100513 2:00:16 [ERROR] Plugin 'InnoDB' init function returned error. 100513 2:00:16 [ERROR] Plugin 'InnoDB' registration as a STORAGE ENGINE failed. 100513 2:00:16 [ERROR] /Applications/MAMP/Library/libexec/mysqld: unknown option '--skip-bdb' 100513 2:00:16 [ERROR] Aborting 100513 2:00:16 [Note] /Applications/MAMP/Library/libexec/mysqld: Shutdown complete 100513 02:00:16 mysqld_safe mysqld from pid file /Applications/MAMP/tmp/mysql/mysql.pid ended A couple of things: 1) There are a bunch of different .cnf files that come with MAMP (my-huge, my-medium, etc.)...how can I tell which one is actually being used? 2) I deleted the ib_logfile0 and ib_logfile1 as recommended by another post on serverfault, and then ended up with more errors: 100519 16:01:30 InnoDB: Log file /usr/local/mysql/data/ib_logfile0 did not exist: new to be created InnoDB: Setting log file /usr/local/mysql/data/ib_logfile0 size to 16 MB InnoDB: Database physically writes the file full: wait... 100519 16:01:30 InnoDB: Log file /usr/local/mysql/data/ib_logfile1 did not exist: new to be created InnoDB: Setting log file /usr/local/mysql/data/ib_logfile1 size to 16 MB InnoDB: Database physically writes the file full: wait... InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 100519 16:01:31 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 100519 16:01:31 InnoDB: Started; log sequence number 0 44556 100519 16:01:31 [ERROR] /Applications/MAMP/Library/libexec/mysqld: unknown option '--skip-bdb' 100519 16:01:31 [ERROR] Aborting And then I got this the next time I tried to run it: InnoDB: Unable to lock /usr/local/mysql/data/ibdata1, error: 35 InnoDB: Check that you do not already have another mysqld process InnoDB: using the same InnoDB data or log files. Sorry that this is a lot of information, but I don't want to leave anything out. Thanks.

  Read the article

• overriding new ubuntu installation

  - by tkoomzaaskz

  I've got a ubuntu 11.10 which has lost its support in May 2013, now I'd like to reintall up to the most up-to-date LTS, which is 12.04. My question is regarding my current partitions and doing backups. Is there a safe way to backup my data on some local partitions instead of copying files into DVDs/external drives (this is very uncormortable in my situation). Following are system commands shoing my disk: $ lsblk NAME MAJ:MIN RM SIZE RO MOUNTPOINT sda 8:0 0 232,9G 0 +-sda1 8:1 0 48,8G 0 +-sda2 8:2 0 63G 0 +-sda3 8:3 0 1K 0 +-sda4 8:4 0 53,7G 0 / +-sda5 8:5 0 18,6G 0 +-sda6 8:6 0 25,5G 0 +-sda7 8:7 0 23,3G 0 [SWAP] sr0 11:0 1 1024M 0 and $ sudo fdisk -l [sudo] password for xyz: Disk /dev/sda: 250.1 GB, 250059350016 bytes glowic: 255, sektorów/sciezke: 63, cylindrów: 30401, w sumie sektorów: 488397168 Jednostka = sektorów, czyli 1 * 512 = 512 bajtów Rozmiar sektora (logiczny/fizyczny) w bajtach: 512 / 512 Rozmiar we/wy (minimalny/optymalny) w bajtach: 512 / 512 Identyfikator dysku: 0xc3ffc3ff Device Boot Beginning End Blocks ID System /dev/sda1 * 2048 102402047 51200000 7 HPFS/NTFS/exFAT /dev/sda2 215044096 347080703 66018304 7 HPFS/NTFS/exFAT /dev/sda3 347082750 488392064 70654657+ 5 Extended /dev/sda4 102402048 215042047 56320000 83 Linux /dev/sda5 395905923 434975939 19535008+ 83 Linux /dev/sda6 434976003 488392064 26708031 83 Linux /dev/sda7 347082752 395905023 24411136 82 Linux swap / Solaris In the beginning I had Windows Vista pre-installed with the machine when it was bought (damn!) and I installed linux (the one I have now). The windows-program in master boot record has been overriden by grub and now I can boot with both Windows and Linux. This is list of mounted devices: $ mount /dev/sda4 on / type ext4 (rw,errors=remount-ro,commit=0) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) fusectl on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/tomasz/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=tomasz) It's strange (I don't remember such thing) that my current linux uses only one partition (/dev/sda4). But, anyway, it seems like that. My final question is: am I able to use one of the existing linux partitions for a backup and install ubuntu 12.04 without removing neither windows nor ubuntu 11.04? I mean - will grub automatically accept both old windows vista and 2 linuxes (old 11.10 and "new" 12.04)? Is there any hidden operation done while installation that could harm my custom-backup-partition while installing? my fstab file: proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda4 during installation UUID=d44e89f5-9da2-48eb-83b3-887652ec95d2 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda7 during installation UUID=bbe50535-ba57-434a-9272-211d859f0e00 none swap sw 0 0 sda5 and sda6 are trash partitions created during unsuccessful linux installation (this was linux installation before my current installation), I didn't delete these partitions, but I have access to them (and I can use them as backup partitions). edit: second question is: why does lsblk show /dev/sda having 232,9G while fdisk shows that it has 250.1GB? Where does the difference come from?

  Read the article

• "Possible SYN flooding" in log despite low number of SYN_RECV connections

  - by al4

  Recently we had an apache server which was responding very slowly due to SYN flooding. The workaround for this was to enable tcp_syncookies (net.ipv4.tcp_syncookies=1 in /etc/sysctl.conf). I posted a question about this here if you want more background. After enabling syncookies we started seeing the following message in /var/log/messages approximately every 60 seconds: [84440.731929] possible SYN flooding on port 80. Sending cookies. Vinko Vrsalovic informed me that this means the syn backlog is getting full, so I raised tcp_max_syn_backlog to 4096. At some point I also lowered tcp_synack_retries to 3 (down from the default of 5) by issuing sysctl -w net.ipv4.tcp_synack_retries=3. After doing this, the frequency seemed to drop, with the interval of the messages varying between roughly 60 and 180 seconds. Next I issued sysctl -w net.ipv4.tcp_max_syn_backlog=65536, but am still getting the message in the log. Throughout all this I've been watching the number of connections in SYN_RECV state (by running watch --interval=5 'netstat -tuna |grep "SYN_RECV"|wc -l'), and it never goes higher than about 240, much much lower than the size of the backlog. Yet I have a Red Hat server which hovers around 512 (limit on this server is the default of 1024). Are there any other tcp settings which would limit the size of the backlog or am I barking up the wrong tree? Should the number of SYN_RECV connections in netstat -tuna correlate to the size of the backlog? Update As best I can tell I'm dealing with legitimate connections here, netstat -tuna|wc -l hovers around 5000. I've been researching this today and found this post from a last.fm employee, which has been rather useful. I've also discovered that the tcp_max_syn_backlog has no effect when syncookies are enabled (as per this link) So as a next step I set the following in sysctl.conf: net.ipv4.tcp_syn_retries = 3 # default=5 net.ipv4.tcp_synack_retries = 3 # default=5 net.ipv4.tcp_max_syn_backlog = 65536 # default=1024 net.core.wmem_max = 8388608 # default=124928 net.core.rmem_max = 8388608 # default=131071 net.core.somaxconn = 512 # default = 128 net.core.optmem_max = 81920 # default = 20480 I then setup my response time test, ran sysctl -p and disabled syncookies by sysctl -w net.ipv4.tcp_syncookies=0. After doing this the number of connections in the SYN_RECV state still remained around 220-250, but connections were starting to delay again. Once I noticed these delays I re-enabled syncookies and the delays stopped. I believe what I was seeing was still an improvement from the initial state, however some requests were still delayed which is much worse than having syncookies enabled. So it looks like I'm stuck with them enabled until we can get some more servers online to cope with the load. Even then, I'm not sure I see a valid reason to disable them again as they're only sent (apparently) when the server's buffers get full. But the syn backlog doesn't appear to be full with only ~250 connections in the SYN_RECV state! Is it possible that the SYN flooding message is a red herring and it's something other than the syn_backlog that's filling up? If anyone has any other tuning options I haven't tried yet I'd be more than happy to try them out, but I'm starting to wonder if the syn_backlog setting isn't being applied properly for some reason.

  Read the article

• Can't re-mount existing RAID10 on Ubuntu

  - by Zoran

  I saw similar questions, but didn't find what solution to my problem. After power-cut, one of RAID10 (4 disks were) appears to be malfunctioning. I make tha array active one, but can not mount it. Always the same error: mount: you must specify the filesystem type So, here is what I have when type mdadm --detail /dev/md0 /dev/md0: Version : 00.90.03 Creation Time : Tue Sep 1 11:00:40 2009 Raid Level : raid10 Array Size : 1465148928 (1397.27 GiB 1500.31 GB) Used Dev Size : 732574464 (698.64 GiB 750.16 GB) Raid Devices : 4 Total Devices : 3 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Mon Jun 11 09:54:27 2012 State : clean, degraded Active Devices : 3 Working Devices : 3 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : 1a02e789:c34377a1:2e29483d:f114274d Events : 0.166 Number Major Minor RaidDevice State 0 8 16 0 active sync /dev/sdb 1 0 0 1 removed 2 8 48 2 active sync /dev/sdd 3 8 64 3 active sync /dev/sde At the /etc/mdadm/mdadm.conf I have by default, scan all partitions (/proc/partitions) for MD superblocks. alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes automatically tag new arrays as belonging to the local system HOMEHOST <system> instruct the monitoring daemon where to send mail alerts MAILADDR root definitions of existing MD arrays ARRAY /dev/md0 level=raid10 num-devices=4 UUID=1a02e789:c34377a1:2e29483d:f114274d ARRAY /dev/md1 level=raid1 num-devices=2 UUID=9b592be7:c6a2052f:2e29483d:f114274d This file was auto-generated... So, my question is, how can I mount md0 array (md1 has been mounted without problem) in order to preserve existing data? One more thing, fdisk -l command gives the following result: Disk /dev/sdb: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x660a6799 Device Boot Start End Blocks Id System /dev/sdb1 * 1 88217 708603021 83 Linux /dev/sdb2 88218 91201 23968980 5 Extended /dev/sdb5 88218 91201 23968948+ 82 Linux swap / Solaris Disk /dev/sdc: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x0008f8ae Device Boot Start End Blocks Id System /dev/sdc1 1 88217 708603021 83 Linux /dev/sdc2 88218 91201 23968980 5 Extended /dev/sdc5 88218 91201 23968948+ 82 Linux swap / Solaris Disk /dev/sdd: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x4be1abdb Device Boot Start End Blocks Id System Disk /dev/sde: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xa4d5632e Device Boot Start End Blocks Id System Disk /dev/sdf: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xdacb141c Device Boot Start End Blocks Id System Disk /dev/sdg: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xdacb141c Device Boot Start End Blocks Id System Disk /dev/md1: 750.1 GB, 750156251136 bytes 2 heads, 4 sectors/track, 183143616 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk identifier: 0xdacb141c Device Boot Start End Blocks Id System Warning: ignoring extra data in partition table 5 Warning: ignoring extra data in partition table 5 Warning: ignoring extra data in partition table 5 Warning: invalid flag 0x7b6e of partition table 5 will be corrected by w(rite) Disk /dev/md0: 1500.3 GB, 1500312502272 bytes 255 heads, 63 sectors/track, 182402 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x660a6799 Device Boot Start End Blocks Id System /dev/md0p1 * 1 88217 708603021 83 Linux /dev/md0p2 88218 91201 23968980 5 Extended /dev/md0p5 ? 121767 155317 269488144 20 Unknown And one more thing. When using mdadm --examine command, here ise result: mdadm -v --examine --scan /dev/sdb /dev/sdc /dev/sdd /dev/sde /dev/sdf /dev/sd ARRAY /dev/md1 level=raid1 num-devices=2 UUID=9b592be7:c6a2052f:2e29483d:f114274d devices=/dev/sdf ARRAY /dev/md0 level=raid10 num-devices=4 UUID=1a02e789:c34377a1:2e29483d:f114274d devices=/dev/sdb,/dev/sdc,/dev/sdd,/dev/sde md0 has 3 devices which are active. Can someone instruct me how to solve this issue? If it is possible, I would like not to removing faulty HDD. Please advise

  Read the article

• e2fsck / resize2fs problems

  - by BlakBat

  I've got 6 drives (each 1.5T, all same model and firmware revision) that are part of a RAID5 array. The RAID5 makes a LVM volume group and a logical group. The latter contains only one ext3 partition. I've recently ran: e2fsck -f /dev/vg03/lv01 && resize2fs -M /dev/vg03/lv01 which exited without an error. Now when I try to mount /dev/vg03/lv01 I get: EXT3-fs error (device dm-0): ext3_check_descriptors: Block bitmap for group 30533 not in group (block 1000532368)! EXT3-fs: group descriptors corrupted! How do I get out of this predicament? This is all the info I can currently give you: fdisk -l /dev/sd[cdefgh] shows (correctly) that they are "Linux raid autodetect" but fdisk now shows: fdisk -l /dev/md0 Disk /dev/md0: 7501.5 GB, 7501495664640 bytes ... Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table (instead of a LVM type partition) fdisk -l /dev/vg03/lv01 Disk /dev/vg03/lv01: 7501.5 GB, 7501491732480 bytes ... Disk identifier: 0x00000000 Disk /dev/vg03/lv01 doesn't contain a valid partition table (instead of a ext3 type partition) I've tried: e2fsck -fy /dev/vg03/lv01 e2fsck 1.41.12 (17-May-2010) e2fsck: Group descriptors look bad... trying backup blocks... Block bitmap for group 30533 is not in group. (block 1000532368) Relocate? yes Inode bitmap for group 30533 is not in group. (block 1000532369) Relocate? yes Pass 1: Checking inodes, blocks, and sizes Relocating group 30533's block bitmap to 1000524246... Error allocating 1 contiguous block(s) in block group 30533 for inode bitmap: Could not allocate block in ext2 filesystem e2fsck: aborted Extra information I can give you: cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active (auto-read-only) raid5 sdg1[0] sdh1[5] sdf1[4] sde1[3] sdc1[2] sdd1[1] 7325679360 blocks level 5, 128k chunk, algorithm 2 [6/6] [UUUUUU] bitmap: 1/175 pages [4KB], 4096KB chunk unused devices: Lastly, all smartctl tests (short and extendend) showed no errors on any of the disks. Should I try to resize2fs to grow /dev/vg03/lv01 and redo a e2fsck ? Should I cfdisk /dev/md0 and /dev/vg03/lv01 back to their real types? Thanks in advance for all and any help. 2011-09-20 UPDATE I issued the following commands and was able to remount the partition, but by viewing the size (df) of before and after, it seems that 1Tb of data have gone missing. By checking the MD5SUMS (from an old backup) of some files with the "same" files from the remounted partition, some errors have been detected. Commands issued to remount the partition were: dumpe2fs /dev/vg03/lv01 Block count: 1000491435<br /> Block size: 4096<br /> tune2fs -O ^has_journal /dev/vg03/lv01 resize2fs -p /dev/vg03/lv01 dumpe2fs /dev/vg03/lv01 Block count: 1831418880<br /> Block size: 4096<br /> mount -o ro,noatime /dev/vg03/lv01 /mnt/raid OK... but files have been damaged / gone missing.

  Read the article

• ubuntu mount iso but some files are unreadable

  - by Chao

  I'm new to Linux and just installed ubuntu 12.04 amd64 this month. I had failed installing Texlive with texlive2012 iso image. I used the recommended command to mount: "mount -t iso9660 -o ro,loop,noauto /your/texlive2012.iso /mnt " But the installer failed to read some file. The iso is fine, I checked the md5. I extracted everything from iso with archive manager, and it installed successfully. So, why mount is not working? Thanks. UPDATE with furius iso mount tool, mount with Fuse, and it installed, with warning: Summary of warning messages during installation: Downloaded ./archive/calligra-type1.tar.xz, size equal, but md5sum differs; downloading again. While mount with Loop, it failed to install. Updated Error message from terminal, mounted with furius iso mount, loop. texlive2012-20120701_iso$ ./install-tl -gui Loading ./tlpkg/texlive.tlpdb Installing TeX Live 2012 from: . Platform: x86_64-linux = 'x86_64 with GNU/Linux' Distribution: inst (compressed) Directory for temporary files: /tmp Installing [0001/2481, time/total: ??:??/??:??]: 12many [3k] Installing [0002/2481, time/total: 00:00/00:00]: 2up [4k] Installing [0003/2481, time/total: 00:00/00:00]: Asana-Math [457k] Installing [0004/2481, time/total: 00:00/00:00]: ESIEEcv [2k] ... Installing [0265/2481, time/total: 00:10/01:09]: calctab [5k] Installing [0266/2481, time/total: 00:10/01:09]: calligra [42k] Installing [0267/2481, time/total: 00:10/01:09]: calligra-type1 [59k] Downloaded ./archive/calligra-type1.tar.xz, size equal, but md5sum differs; downloading again. ./tlpkg/installer/xz/xzdec.x86_64-linux: (stdin): File is corrupt tar: Unexpected EOF in archive tar: rmtlseek not stopped at a record boundary tar: Error is not recoverable: exiting now untar: untarring /home/lichao/ttt/temp/calligra-type1.tar failed (in /home/lichao/ttt/texmf-dist) untarring /home/lichao/ttt/temp/calligra-type1.tar failed, stopping install. Installation failed. Rerunning the installer will try to restart the installation. Or you can restart by running the installer with: install-tl --profile installation.profile [EXTRA-ARGS] ./install-tl: Could not write to install-tl.log, so flushing messages to stderr. Loading ./tlpkg/texlive.tlpdb Installing TeX Live 2012 from: . Platform: x86_64-linux = 'x86_64 with GNU/Linux' Distribution: inst (compressed) Directory for temporary files: /tmp Installer revision: 26794 Database revision: 26935 Installing [0001/2481, time/total: ??:??/??:??]: 12many [3k] Installing [0002/2481, time/total: 00:00/00:00]: 2up [4k] Installing [0003/2481, time/total: 00:00/00:00]: Asana-Math [457k] Installing [0004/2481, time/total: 00:00/00:00]: ESIEEcv [2k] Installing [0005/2481, time/total: 00:00/00:00]: FAQ-en [1k] ... Installing [0262/2481, time/total: 00:10/01:09]: c90 [2k] Installing [0263/2481, time/total: 00:10/01:09]: cachepic [5k] Installing [0264/2481, time/total: 00:10/01:09]: cachepic.x86_64-linux [1k] Installing [0265/2481, time/total: 00:10/01:09]: calctab [5k] Installing [0266/2481, time/total: 00:10/01:09]: calligra [42k] Installing [0267/2481, time/total: 00:10/01:09]: calligra-type1 [59k] Downloaded ./archive/calligra-type1.tar.xz, size equal, but md5sum differs; downloading again. untar: untarring /home/lichao/ttt/temp/calligra-type1.tar failed (in /home/lichao/ttt/texmf-dist) untarring /home/lichao/ttt/temp/calligra-type1.tar failed, stopping install. Installation failed. Rerunning the installer will try to restart the installation. Or you can restart by running the installer with: install-tl --profile installation.profile [EXTRA-ARGS] Segmentation fault (core dumped) I am sure that the iso is fine. I can open it with archive manager and all files are good. But after mounting it, even archive manager failed to open some files (which can be opened when the iso is opened in archive manager).

  Read the article

• Lustre - issues with simple setup

  - by ethrbunny

  Issue: I'm trying to assess the (possible) use of Lustre for our group. To this end I've been trying to create a simple system to explore the nuances. I can't seem to get past the 'llmount.sh' test with any degree of success. What I've done: Each system (throwaway PCs with 70Gb HD, 2Gb RAM) is formatted with CentOS 6.2. I then update everything and install the Lustre kernel from downloads.whamcloud.com and add on the various (appropriate) lustre and e2fs RPM files. Systems are rebooted and tested with 'llmount.sh' (and then cleared with 'llmountcleanup.sh'). All is well to this point. First I create an MDS/MDT system via: /usr/sbin/mkfs.lustre --mgs --mdt --fsname=lustre --device-size=200000 --param sys.timeout=20 --mountfsoptions=errors=remount-ro,user_xattr,acl --param lov.stripesize=1048576 --param lov.stripecount=0 --param mdt.identity_upcall=/usr/sbin/l_getidentity --backfstype ldiskfs --reformat /tmp/lustre-mdt1 and then mkdir -p /mnt/mds1 mount -t lustre -o loop,user_xattr,acl /tmp/lustre-mdt1 /mnt/mds1 Next I take 3 systems and create a 2Gb loop mount via: /usr/sbin/mkfs.lustre --ost --fsname=lustre --device-size=200000 --param sys.timeout=20 --mgsnode=lustre_MDS0@tcp --backfstype ldiskfs --reformat /tmp/lustre-ost1 mkdir -p /mnt/ost1 mount -t lustre -o loop /tmp/lustre-ost1 /mnt/ost1 The logs on the MDT box show the OSS boxes connecting up. All appears ok. Last I create a client and attach to the MDT box: mkdir -p /mnt/lustre mount -t lustre -o user_xattr,acl,flock luster_MDS0@tcp:/lustre /mnt/lustre Again, the log on the MDT box shows the client connection. Appears to be successful. Here's where the issues (appear to) start. If I do a 'df -h' on the client it hangs after showing the system drives. If I attempt to create files (via 'dd') on the lustre mount the session hangs and the job can't be killed. Rebooting the client is the only solution. If I do a 'lctl dl' from the client it shows that only 2/3 OST boxes are found and 'UP'. [root@lfsclient0 etc]# lctl dl 0 UP mgc MGC10.127.24.42@tcp 282d249f-fcb2-b90f-8c4e-2f1415485410 5 1 UP lov lustre-clilov-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 4 2 UP lmv lustre-clilmv-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 4 3 UP mdc lustre-MDT0000-mdc-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 5 4 UP osc lustre-OST0000-osc-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 5 5 UP osc lustre-OST0003-osc-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 5 Doing a 'lfs df' from the client shows: [root@lfsclient0 etc]# lfs df UUID 1K-blocks Used Available Use% Mounted on lustre-MDT0000_UUID 149944 16900 123044 12% /mnt/lustre[MDT:0] OST0000 : inactive device OST0001 : Resource temporarily unavailable OST0002 : Resource temporarily unavailable lustre-OST0003_UUID 187464 24764 152636 14% /mnt/lustre[OST:3] filesystem summary: 187464 24764 152636 14% /mnt/lustre Given that each OSS box has a 2Gb (loop) mount I would expect to see this reflected in available size. There are no errors on the MDS/MDT box to indicate that multiple OSS/OST boxes have been lost. EDIT: each system has all other systems defined in /etc/hosts and entries in iptables to provide access. SO: I'm clearly making several mistakes. Any pointers as to where to start correcting them?

  Read the article

• How do you re-mount an ext3 fs readwrite after it gets mounted readonly from a disk error?

  - by cagenut

  Its a relatively common problem when something goes wrong in a SAN for ext3 to detect the disk write errors and remount the filesystem read-only. Thats all well and good, only when the SAN is fixed I can't figure out how to re-re-mount the filesystem read-write without rebooting. Behold: [root@localhost ~]# multipath -ll mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=1 queue_if_no_path][hwhandler=0][rw] \_ round-robin 0 [prio=2][active] \_ 1:0:0:1 sdb 8:16 [active][ready] \_ 2:0:0:1 sdc 8:32 [active][ready] [root@localhost ~]# mount /dev/mapper/mpath0 /mnt/foo [root@localhost ~]# touch /mnt/foo/blah All good, now I yank the LUN out from under it. [root@localhost ~]# touch /mnt/foo/blah [root@localhost ~]# touch /mnt/foo/blah touch: cannot touch `/mnt/foo/blah': Read-only file system [root@localhost ~]# tail /var/log/messages Mar 18 13:17:33 localhost multipathd: sdb: tur checker reports path is down Mar 18 13:17:34 localhost multipathd: sdc: tur checker reports path is down Mar 18 13:17:35 localhost kernel: Aborting journal on device dm-2. Mar 18 13:17:35 localhost kernel: Buffer I/O error on device dm-2, logical block 1545 Mar 18 13:17:35 localhost kernel: lost page write due to I/O error on dm-2 Mar 18 13:17:36 localhost kernel: ext3_abort called. Mar 18 13:17:36 localhost kernel: EXT3-fs error (device dm-2): ext3_journal_start_sb: Detected aborted journal Mar 18 13:17:36 localhost kernel: Remounting filesystem read-only It only thinks its read-only, in reality its not even there. [root@localhost ~]# multipath -ll sdb: checker msg is "tur checker reports path is down" sdc: checker msg is "tur checker reports path is down" mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=0][hwhandler=0][rw] \_ round-robin 0 [prio=0][enabled] \_ 1:0:0:1 sdb 8:16 [failed][faulty] \_ 2:0:0:1 sdc 8:32 [failed][faulty] [root@localhost ~]# ll /mnt/foo/ ls: reading directory /mnt/foo/: Input/output error total 20 -rw-r--r-- 1 root root 0 Mar 18 13:11 bar How it still remembers that 'bar' file being there... mystery, but not important right now. Now I re-present the LUN: [root@localhost ~]# tail /var/log/messages Mar 18 13:23:58 localhost multipathd: sdb: tur checker reports path is up Mar 18 13:23:58 localhost multipathd: 8:16: reinstated Mar 18 13:23:58 localhost multipathd: mpath0: queue_if_no_path enabled Mar 18 13:23:58 localhost multipathd: mpath0: Recovered to normal mode Mar 18 13:23:58 localhost multipathd: mpath0: remaining active paths: 1 Mar 18 13:23:58 localhost multipathd: dm-2: add map (uevent) Mar 18 13:23:58 localhost multipathd: dm-2: devmap already registered Mar 18 13:23:59 localhost multipathd: sdc: tur checker reports path is up Mar 18 13:23:59 localhost multipathd: 8:32: reinstated Mar 18 13:23:59 localhost multipathd: mpath0: remaining active paths: 2 Mar 18 13:23:59 localhost multipathd: dm-2: add map (uevent) Mar 18 13:23:59 localhost multipathd: dm-2: devmap already registered [root@localhost ~]# multipath -ll mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=1 queue_if_no_path][hwhandler=0][rw] \_ round-robin 0 [prio=2][enabled] \_ 1:0:0:1 sdb 8:16 [active][ready] \_ 2:0:0:1 sdc 8:32 [active][ready] Great right? It says [rw] right there. Not so fast: [root@localhost ~]# touch /mnt/foo/blah touch: cannot touch `/mnt/foo/blah': Read-only file system OK, doesn't do it automatically, I'll just give it a little push: [root@localhost ~]# mount -o remount /mnt/foo mount: block device /dev/mapper/mpath0 is write-protected, mounting read-only The hell you are: [root@localhost ~]# mount -o remount,rw /mnt/foo mount: block device /dev/mapper/mpath0 is write-protected, mounting read-only Noooooooooo. I have tried all sorts of different mount/tune2fs/dmsetup commands and I cannot figure out how to get it to un-flag the block device as write-protected. Rebooting will fix it, but I'd much rather do it on-line. An hour of googling has gotten me nowhere either. Save me ServerFault.

  Read the article

• AMD Catalyst 13.9 installation failure

  - by Simon Verbeke

  Earlier today I installed Windows 8.1, and when I wanted to go into Catalyst Control Center, I noticed some odd error of CCC not being able to display options. I then figured I needed a driver update, so I downloaded the latest drivers, version 13.9, and tried to install them. While it was trying to install the display drivers, I got a blue screen. Tried again and got the same. Then I used an uninstall tool from AMD to remove all traces of my old drivers and tried to install the new drivers. Again, a blue screen. This is all I could think of to try. Would anyone know some other things I can try? EDIT: thought I might want to include the log entry for the crash: - <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> - <System> <Provider Name="Microsoft-Windows-WER-SystemErrorReporting" Guid="{ABCE23E7-DE45-4366-8631-84FA6C525952}" EventSourceName="BugCheck" /> <EventID Qualifiers="16384">1001</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2013-10-19T20:59:25.000000000Z" /> <EventRecordID>26587</EventRecordID> <Correlation /> <Execution ProcessID="0" ThreadID="0" /> <Channel>System</Channel> <Computer>Simon-PC</Computer> <Security /> </System> - <EventData> <Data Name="param1">0x0000007e (0xffffffffc0000005, 0xfffff80002a86dca, 0xffffd00025f250e8, 0xffffd00025f248f0)</Data> <Data Name="param2">C:\WINDOWS\MEMORY.DMP</Data> <Data Name="param3">101913-8953-01</Data> </EventData> </Event> Another edit: As it turns out, the graphics card isn't showing up any more in the device manager. But as far as I can tell, it is still working (the fans are spinning and my screen is plugged into that graphics card). This is solved. it appears that my graphics card is now running with a default windows driver. I also tried the forced method mentioned here: AMD Graphics Drivers won't install properly . But I still get a BSOD. Third edit: Slight succes! Managed to install version 13.4. Everything appears to be working fine now. I think I'm just going to skip version 13.9.

  Read the article

• Windows 7 is stuck at "Starting Windows" when I attempt to boot computer

  - by Eli

  Basically, whenever I turn on my computer, it gets to the Starting Windows phase and just stays there. The startup animation still plays, yet it gets nowhere. I have tried booting into safe mode, however it gets stuck at loading CLASSPNP.SYS. It then freezes there and doesn't continue booting. I have tried booting into recovery mode from the hard drive, and it freezes after displaying the background image. I have tried booting from a recovery CD, which works, and I was able to use system restore. However, using system restore did not fix it, and it still is stuck at the Starting Windows screen. I have tried booting a Windows CD (Windows 8 Retail Installer) to see if I could upgrade it to fix this issue, however that froze at a blank screen after it got past the boot logo. I have tried changing around the BIOS settings (including resetting), to no avail. I have tried re-plugging the internal PSU cables (this is a custom-built desktop), yet this has changed nothing. I can boot into a loopback Ubuntu install on the same drive, which works fine, other than the fact that it has issues with some of the USB ports and the network card. This system has worked fine for the past few months, completely stable, and nothing in the configuration has changed before this error started happening. Startup Repair on the Windows recovery CD doesn't find any issues. Unplugging my secondary hard drive or swapping around memory doesn't change anything. The hard drive itself is fine, it hasn't shown any signs of failure and once again, boots my other OS fine. If anyone could help with this, that would be great. I can't seem to find any possible solution to this. If it makes any difference, my system specs are as follows: AMD FX-8320 Gigabyte GA-970A-D3 4GB of DDR3 Radeon HD 6870 550w PSU I'd like to not have to reinstall Windows, for I have more than a terabyte of data that I would have to back up if that becomes the only option. EDIT: I have since tried the following: Tried the solution involving restoring files from RegBackup, which changed nothing. Tried testing everything with Hiren's boot CD, everything comes back as fine. Tried disabling everything unnecessary in the BIOS and unplugging everything unneeded, it still hangs. Tried swapping out every possible combination of RAM, it still has the same result. The RAM is not at fault it seems Tried every GPU I own (which is many!) and it still hangs at the exact same place. Tried minimizing the power consumption as much as possible, even using an old PCI graphics card. It still hangs at the same place in the same way, signifying that it's not the PSU at fault. Tried resetting the BIOS again, still nothing. Tried every possible combination of BIOS options, even downclocking everything, it still hangs in the same spot. Tried upgrading the BIOS from version FB to FD, which changed nothing. Based on this, I would conclude the motherboard to be at fault. Are there any other possibilities? I don't want to spend $150 for a new motherboard. EDIT 2: This is what it gets stuck at when I try to boot into safe mode: Note the slight graphical corruption at the top of the screen. No matter how I set up the system, this seems to be there. In addition, either it has stopped booting into safe mode now, or it takes upwards of 2+ hours, and I haven't left it running for that long.

  Read the article

• How to reinstall OEM Windows 98 SE?

  - by Sammy

  I'm trying to install Windows 98 SE on an old PC and it's not going well. I run into this problem. Searching for Boot Record from Floppy..OK Starting Windows 98... TOSHIBA Enhanced-IDE CD/DVD-ROM Device Driver (ATAPI) Version 2.24 (C)Copyright Toshiba Corp. 1995-1999. All rights reserved. Device Name : TOSCD001 Number of units : 1 MSCDEX Version 2.25 Copyright (C) MIcrosoft Corp. 1986-1995. All rights reserved. Drive Z: = Driver TOSCD001 unit 0 TOSHIBA MACHINE Invalid drive specification Path not found - C:\TOOLS\CDROMDRV.SYS Invalid drive specification Invalid drive specification After that last line, it leaves me at a bitmap image displaying instructions to reboot with Ctrl+Alt+Del. It doesn't say why I have to reboot, and it doesn't state any error type, it just want's me to reboot for no apparent reason. After reboot, it just boots up from Floppy again and it cycles through the same thing all over again. The computer has been restored to original specification. Original system recovery "CD-ROM" discs are available and they are not scratched or anything, they are in very good condition. It's a set of 3 CDs, and the first disc labeled "1/3" should be the one holding the OEM version of Windows 98 SE. There is also a boot disk for Windows 98. I'm not sure what the other two discs are for. This computer came with three language support, so those could be holding different language versions or additional OEM discs. But I'm quite sure that the first disc holds the main operating system. BIOS has been set to optimized defaults. Boot priority is as follows; Floppy, IDE-0, CD-ROM. Under Standard CMOS settings, BIOS scans and autoconfigures both the hard drive and the CD/DVD drive. On POST it finds them both, and it finds the DOS bootdisk and starts preparing for installation, as you can see above. So what's this "invalid drive specification" about? Why isn't the installation starting? Updates Update 1 Booting from CD disc 2 In desperation I tried booting from the second CD. Boot order was; Floppy, CD-ROM, IDE-0. It boots normally from floppy disk, just like above, but then returns following. File not found - Z:\3LNGINST\TOOLS\PARTINFO.TXT I accidentally pressed some key on the keyboard, and before I knew it, the following screen showed up. Create Primary DOS Partition Current fixed disk drive: 1 Verifying drive integrity, 16% complete. After completion another screen showed up. Create Primary DOS Partition Current fixed disk drive: 1 Do you wish to use the maximum available size for a Primary DOS Partition and make the partition active (Y/N)?....................? [Y] Verifying drive integrity, 7% complete. I didn't choose Yes, it was set automatically. After completion the computer was automatically rebooted. Then I got a new screen. This is in Norwegian/Swedish/Finnish. Here's the message in Swedish. Hårddisken är inte klar för återställning av programvara. Installationsprogrammet måste skapa nya partitioner (C:, D:, ...). VARNING! ALLT INNEHÅLL PÅ HÅRDDISKEN KOMMER ATT RADERAS! Tryck på en tangent om du vill fortsätta (eller CTRL-C för att avbryta). Let me translate that. Hard drive is not ready for restoring the software. Setup program has to create new partitions (C:, D:, ...). WARNING! ALL CONTENTS ON THE HARD DRIVE WILL BE ERASED! Press any key to continue (or CTRL-C to cancel). I pressed Enter and it started formatting the hard drive. WARNING, ALL DATA ON NON-REMOVABLE DISK DRIVE c: WILL BE LOST! Proceed with Format (Y/N)?y Formatting 14,67.53M 1 percent completed. It automatically sets the "y" option and starts formatting. Rebooting with CD disc 1 After completing this operation it rebooted automatically. I inserted CD disc 1 and there was no issue with "invalid drive specification" anymore. Instead, a bitmap menu was displayed where it asked me to choose a language. And I thought I had it there for a while but it didn't work out. After choosing the language, another menu was displayed asking me to choose a type of recovery (restore pre-installed software OR restore hard drive partitions and pre-installed software). I opted for the second option. Then a data destruction warning showed up where I just pressed 1 to Continue. It did something and then just rebooted and the same formatting screen shows up as before. So something is not right. Am I doing it wrong? I seem to have come past the CD-ROM driver issue at least. But now I'm stuck with this problem... it seems to have something to do with the hard drive. Like... why is is it always trying to format it? Isn't it enough to format it once? By the way, it needs to be formatted as FAT32, right? Windows 98 doesn't support NTFS? I think FDISK should have taken care of this already. I know this is an old hard drive, but I connected to my main computer and it was able to read and write to it without a problem. It does have bad sectors though, but it's expected on an old hard drive like this. Any ideas?.. Update 2 I seem to be repeatedly getting stuck at the format screen where it asks to press any key to continue. So tried to cancel it this time with Ctrl+C. This leaves me at: A:\TOOLS> I can do DIR and CD and I tried to change to Z: drive. I tried running "setup" but there is no such thing. Z:\>setup Bad command or file name Update 3 Floppy structure Here's the file/folder structure of the floppy disk. A:\>dir /s Volume in drive A has no label. Volume Serial Number is 1700-1069 Directory of A:\ 1999-10-11 10:44 <DIR> BMP 1998-05-11 22:01 93 880 COMMAND.COM 1999-10-11 10:44 <DIR> factory 1999-10-11 10:44 <DIR> lang 1999-10-11 10:44 <DIR> TOOLS 2000-05-19 15:32 339 CONFIG.SYS 1999-10-26 13:38 0 BOOTLOG.TXT 2000-06-08 08:32 3 691 AUTOEXEC.BAT 4 File(s) 97 910 bytes Directory of A:\BMP 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 0 File(s) 0 bytes Directory of A:\factory 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 2000-06-08 13:09 2 662 3LNGINSF.BAT 1 File(s) 2 662 bytes Directory of A:\lang 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 1998-11-24 08:02 49 575 FORMAT.COM 1998-11-24 08:02 63 900 FDISK.EXE 2 File(s) 113 475 bytes Directory of A:\TOOLS 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 1998-05-06 22:01 49 575 FORMAT.COM 1995-10-27 20:29 28 164 BMPVIEW.EXE 1999-01-26 15:54 15 MAKEPA32.TXT 1998-05-06 22:01 3 878 XCOPY.EXE 1998-05-06 22:01 41 472 XCOPY32.MOD 1998-05-06 22:01 33 191 HIMEM.SYS 1998-05-06 22:01 125 495 EMM386.EXE 1998-05-06 22:01 18 967 SYS.COM 1996-01-31 21:55 18 CLK.COM 1994-04-02 08:20 22 HARDBOOT.COM 1999-02-03 15:46 15 MAKEPA16.TXT 1999-04-14 16:36 7 840 PARTFO32.EXE 2000-05-19 15:01 1 169 PARTFORM.BAT 1996-10-02 01:47 1 642 MBRCLR.COM 1999-07-01 11:58 8 175 BIOSCHKN.EXE 1998-06-23 08:55 5 904 PAR-TYPE.EXE 1998-11-24 08:02 29 271 MODE.COM 1998-11-24 08:02 15 252 ATTRIB.EXE 1998-11-24 08:02 19 083 DELTREE.EXE 1999-04-21 15:01 23 304 NTBB.EXE 1997-05-07 14:19 1 SYS.TXT 1999-07-01 12:23 61 566 F3DCHK.EXE 1998-05-11 20:01 34 566 KEYBOARD.SYS 1998-05-11 20:01 19 927 KEYB.COM 1999-10-26 14:31 910 partinfo.txt 1998-06-16 15:58 5 936 CHKDRVAC.EXE 1998-05-06 22:01 63 900 FDISK.EXE 1998-05-06 22:01 45 379 SMARTDRV.EXE 1992-12-03 19:48 10 695 SCISET.EXE 1997-06-25 15:49 6 YENT 1998-05-06 22:01 25 473 MSCDEX.EXE 1998-05-06 22:01 5 239 CHOICE.COM 1997-07-18 17:41 6 876 MBR.COM 1997-07-01 15:01 6 545 CHK2GB.COM 1998-06-10 20:04 8 128 PARTFORM.EXE 1990-01-04 02:09 19 MAKEPAR2.TXT 1990-01-04 01:00 27 MAKEPAR3.TXT 1990-01-04 01:00 27 MAKEPAR4.TXT 1998-02-13 13:47 15 MAKEPART.TXT 1999-04-14 13:47 5 200 DISKSIZE.EXE 1999-05-06 14:56 7 856 PARTFO16.EXE 1999-01-13 11:13 13 720 CDROMDRV.SYS 42 File(s) 734 463 bytes Total Files Listed: 49 File(s) 948 510 bytes 12 Dir(s) 268 800 bytes free A:\> CONFIG.SYS contents Here's the content of CONFIG.SYS. DEVICE=A:\TOOLS\HIMEM.SYS /TESTMEM:OFF REM I=B000-B7ff for Desktop BIOSes rem DEVICE=A:\TOOLS\EMM386.EXE NOEMS I=B000-B7ff x=C000-D000 DEVICE=A:\TOOLS\EMM386.EXE NOEMS x=C000-D000 DEVICE=A:\TOOLS\CDROMDRV.SYS /D:TOSCD001 BUFFERS=10 FILES=69 DOS=HIGH,UMB STACKS=9,256 LASTDRIVE=Z SWITCHES=/F SHELL=A:\COMMAND.COM /P /E:2048 AUTOEXEC.BAT contents :BEGIN @ECHO OFF PATH=A:\;A:\TOOLS; MSCDEX /D:TOSCD001 /L:Z /M:10 smartdrv 1024 128 SET TOOLS=A:\TOOLS SET COMSPEC=A:\COMMAND.COM SET EXITDRIVE=C: SET EXITPATH=\ CALL Z:\SETENV.BAT > NUL :TOSHCHK BIOSChkN IF NOT ERRORLEVEL 1 goto C_ACCESS BMPVIEW Z:\3LNGINST\BMP\NO_TOSP3.bmp /X=120 /Y=80 PAUSE > NUL SET EXITDRIVE=A: GOTO END :C_ACCESS CALL PARTFORM.BAT :C_EMPTY IF EXIST C:\*.* GOTO C_NOTEMPTY call z:\setenv.bat>nul goto PREPDU :C_NOTEMPTY REM ------------------MENU------------------------ :STARTMENU CLS BMPVIEW Z:\3LNGINST\BMP\LANGSELC.BMP /X=120 /Y=120 CLK CHOICE /C:123 /N >NUL REM L is the language that is selected IF ERRORLEVEL 1 SET L=%LNG1% IF ERRORLEVEL 2 SET L=%LNG2% IF ERRORLEVEL 3 SET L=%LNG3% SET BMP=BMP%L% BMPVIEW Z:\3LNGINST\%bmp%\HDDMENU.BMP /X=72 /Y=82 CLK CHOICE /C:129F /N > NUL IF ERRORLEVEL 4 GOTO FACTORY_MENU IF ERRORLEVEL 3 GOTO EXIT_MENU IF ERRORLEVEL 2 GOTO PARTFORM_MENU IF ERRORLEVEL 1 GOTO FORMAT_MENU GOTO END :FACTORY_MENU BMPVIEW Z:\3LNGINST\%bmp%\qformat.bmp /X=120 /Y=140 CLK choice /c:12 /N >nul IF ERRORLEVEL 2 GOTO STARTMENU IF ERRORLEVEL 1 GOTO FORMATF GOTO END :EXIT_MENU BMPVIEW Z:\3LNGINST\%bmp%\9.bmp /XC /X=96 /Y=267 choice /C:1pause /T:1,01 >nul SET EXITDRIVE=A: SET EXITPATH=\lang cls mode mono rem keyb xx>nul cls GOTO END :PARTFORM_MENU BMPVIEW Z:\3LNGINST\%bmp%\2.bmp /XC /X=96 /Y=216 choice /C:1pause /T:1,01 >nul BMPVIEW Z:\3LNGINST\%bmp%\partform.bmp /X=120 /Y=140 CLK choice /c:12 /N >nul IF ERRORLEVEL 2 GOTO STARTMENU IF ERRORLEVEL 1 GOTO PART_FORM SET EXITDRIVE=A: GOTO END :FORMAT_MENU BMPVIEW Z:\3LNGINST\%bmp%\1.bmp /XC /X=96 /Y=165 choice /C:1pause /T:1,01 >nul BMPVIEW Z:\3LNGINST\%bmp%\qformat.bmp /X=120 /Y=140 CLK choice /c:12 /N >nul IF ERRORLEVEL 2 GOTO STARTMENU IF ERRORLEVEL 1 GOTO FORMAT SET EXITDRIVE=A: GOTO END REM ------------------ MENU END ------------------------ :FORMAT bmpview Z:\3LNGINST\%bmp%\1.bmp /XC /X=145 /Y=235 choice /C:1pause /T:1,01 >nul CLS IF (%QFORMAT%)==(NO) GOTO FULLFO FORMAT C: /Q /V:"" <A:\TOOLS\YENT >NUL call z:\setenv.bat>nul goto PREPDU :FULLFO FORMAT C: /V:"" <A:\TOOLS\YENT call z:\setenv.bat>nul goto PREPDU :FORMATF CLS IF (%QFORMAT%)==(NO) GOTO FULLFO_F FORMAT C: /Q /V:"" <A:\TOOLS\YENT >NUL call z:\setenv.bat>nul goto PREPDU_F :FULLFO_F FORMAT C: /V:"" <A:\TOOLS\YENT call z:\setenv.bat>nul goto PREPDU_F :PART_FORM bmpview Z:\3LNGINST\bmp\1.bmp /XC /X=145 /Y=235 choice /C:1pause /T:1,01 >nul MBR /! HARDBOOT REM ====================== Triple Select ====================== :PREPDU XCOPY z:\3LNGINST\*.* C:\*.* /E /S /V >NUL ATTRIB -H -R -S C:\TOOLS\CDROMDRV.SYS COPY A:\TOOLS\CDROMDRV.SYS C:\TOOLS /Y SYS C: >NUL goto REBOOT :PREPDU_F copy A:\TOOLS\SMARTDRV.EXE C:\ /Y ATTRIB -H -R -S C:\SMARTDRV.EXE copy A:\FACTORY\3LNGINSF.bat c:\ c:\3LNGINSF.bat cls REM ====================== Dual Select END ====================== REM --------------- END ------------------ :REBOOT SMARTDRV.EXE /C bmpview Z:\3LNGINST\BMP\reboot3.bmp /X=120 /Y=140 :FOREVER pause >nul goto FOREVER :END SMARTDRV.EXE /C %EXITDRIVE% cd %EXITPATH% echo on CD structure S:\>dir /s Volume in drive S is T3ELK4SC Volume Serial Number is 2042-5BC9 Directory of S:\ 2000-08-22 14:14 <DIR> 3LNGINSF 2000-08-22 14:14 <DIR> 3LNGINST 2000-06-15 15:57 <DIR> CRC 2000-06-15 12:04 387 667 767 T310C1NO.W98 2000-09-07 15:36 273 setenv.BAT 2 File(s) 387 668 040 bytes Directory of S:\3LNGINSF 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1999-10-27 10:51 1 806 AUTOEXEC.BAT 2000-08-22 14:14 <DIR> BMP 2000-05-19 15:29 265 CONFIG.SYS 2000-08-22 14:14 <DIR> POSTINST 2000-08-22 14:14 <DIR> TOOLS 2000-08-22 14:14 <DIR> WIN98SYS 2 File(s) 2 071 bytes Directory of S:\3LNGINSF\BMP 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1999-01-04 02:38 718 3.BMP 2000-07-05 11:22 60 118 Cdchg2.bmp 2000-07-05 11:22 60 118 Cdchg3.bmp 2000-07-05 13:37 60 118 Fin.bmp 2000-07-06 14:18 120 118 Menu.bmp 2000-07-05 13:34 60 118 Nor.bmp 2000-07-05 11:53 35 318 Progress.bmp 2000-07-05 13:40 60 118 Swe.bmp 2000-07-05 12:09 84 118 Wrongcd2.bmp 2000-07-05 12:09 84 118 Wrongcd3.bmp 12 File(s) 626 416 bytes Directory of S:\3LNGINSF\POSTINST 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-05-19 09:15 33 POSTINST.BAT 1 File(s) 33 bytes Directory of S:\3LNGINSF\TOOLS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-07-06 14:49 3 593 3LNGINST.BAT 1998-11-24 08:02 15 252 ATTRIB.EXE 1995-10-27 18:29 28 164 BMPVIEW.EXE 1999-01-13 11:13 13 720 CDROMDRV.SYS 1998-05-06 20:01 5 239 CHOICE.COM 1996-01-31 19:55 18 CLK.COM 1998-11-24 08:02 19 083 DELTREE.EXE 1998-05-06 20:01 125 495 EMM386.EXE 1999-07-01 12:23 61 566 F3DCHK.EXE 1998-05-06 20:01 49 575 FORMAT.COM 1994-04-02 06:20 22 HARDBOOT.COM 1998-05-06 20:01 33 191 HIMEM.SYS 1998-05-06 20:01 25 473 MSCDEX.EXE 1998-05-06 20:01 12 663 RAMDRIVE.SYS 1998-05-06 20:01 45 379 SMARTDRV.EXE 1997-05-07 14:19 1 SYS.TXT 1995-09-27 14:25 6 813 VOLCHECK.EXE 1998-05-06 20:01 3 878 XCOPY.EXE 1998-05-06 20:01 41 472 XCOPY32.MOD 1997-06-25 13:49 6 YENT 20 File(s) 490 603 bytes Directory of S:\3LNGINSF\WIN98SYS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1998-12-04 20:00 222 390 IO.SYS 1998-05-06 20:01 18 967 SYS.COM 1998-05-06 20:01 93 880 command.com 3 File(s) 335 237 bytes Directory of S:\3LNGINST 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1999-05-31 09:51 1 576 AUTOEXEC.BAT 2000-08-22 14:14 <DIR> BMP 2000-08-22 14:14 <DIR> Bmpfin 2000-08-22 14:14 <DIR> Bmpnor 2000-08-22 14:14 <DIR> Bmpswe 2000-05-19 15:30 265 CONFIG.SYS 2000-08-22 14:14 <DIR> POSTINST 2000-08-22 14:14 <DIR> TOOLS 2000-08-22 14:14 <DIR> WIN98SYS 2 File(s) 1 841 bytes Directory of S:\3LNGINST\BMP 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1999-01-04 02:38 718 3.BMP 2000-07-05 11:22 60 118 Cdchg2.bmp 2000-07-05 11:22 60 118 Cdchg3.bmp 2000-07-05 13:37 60 118 Fin.bmp 2000-07-06 14:18 120 118 Menu.bmp 2000-07-05 13:34 60 118 Nor.bmp 2000-07-05 11:53 35 318 Progress.bmp 2000-07-06 14:08 40 518 Reboot3.bmp 2000-07-05 13:40 60 118 Swe.bmp 2000-07-05 12:09 84 118 Wrongcd2.bmp 2000-07-05 12:09 84 118 Wrongcd3.bmp 2000-07-05 13:52 48 118 langselc.bmp 2000-07-05 11:47 57 318 no_tosp3.bmp 15 File(s) 772 370 bytes Directory of S:\3LNGINST\Bmpfin 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1998-06-13 00:07 718 9.bmp 2000-03-08 15:02 78 486 Hddmenu.bmp 2000-03-08 15:31 25 318 No_tospc.bmp 2000-03-08 15:37 36 518 PARTFORM.BMP 2000-03-08 15:42 36 518 Qformat.bmp 7 File(s) 178 994 bytes Directory of S:\3LNGINST\Bmpnor 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1998-06-13 00:07 718 9.bmp 1999-05-05 13:26 78 486 Hddmenu.bmp 1998-07-13 11:36 25 318 No_tospc.bmp 1998-07-13 11:41 36 518 PARTFORM.BMP 1998-07-13 11:45 36 518 Qformat.bmp 7 File(s) 178 994 bytes Directory of S:\3LNGINST\Bmpswe 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1998-06-13 00:07 718 9.bmp 1999-05-06 08:14 78 486 Hddmenu.bmp 1998-07-10 16:25 25 318 No_tospc.bmp 1998-07-10 16:29 36 518 PARTFORM.BMP 1998-07-10 17:08 36 518 Qformat.bmp 7 File(s) 178 994 bytes Directory of S:\3LNGINST\POSTINST 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-05-19 09:15 33 POSTINST.BAT 1 File(s) 33 bytes Directory of S:\3LNGINST\TOOLS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-05-19 14:52 3 898 3LNGINST.BAT 1995-10-27 18:29 28 164 BMPVIEW.EXE 1999-01-13 11:13 13 720 CDROMDRV.SYS 1998-05-06 20:01 5 239 CHOICE.COM 1996-01-31 19:55 18 CLK.COM 1998-05-06 20:01 125 495 EMM386.EXE 1999-07-01 12:23 61 566 F3DCHK.EXE 1998-05-06 20:01 49 575 FORMAT.COM 1994-04-02 06:20 22 HARDBOOT.COM 1998-05-06 20:01 33 191 HIMEM.SYS 1998-05-06 20:01 25 473 MSCDEX.EXE 2000-07-06 14:41 910 PARTINFO.TXT 1998-05-06 20:01 12 663 RAMDRIVE.SYS 1998-05-06 20:01 45 379 SMARTDRV.EXE 1997-05-07 14:19 1 SYS.TXT 1995-09-27 14:25 6 813 VOLCHECK.EXE 1998-05-06 20:01 3 878 XCOPY.EXE 1998-05-06 20:01 41 472 XCOPY32.MOD 1997-06-25 13:49 6 YENT 19 File(s) 457 483 bytes Directory of S:\3LNGINST\WIN98SYS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1998-12-04 20:00 222 390 IO.SYS 1998-05-06 20:01 18 967 SYS.COM 1998-05-06 20:01 93 880 command.com 3 File(s) 335 237 bytes Directory of S:\CRC 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-06-15 12:07 181 422 T310C1NO.ALL 2000-06-15 12:09 215 427 T310C1NO.CRC 2000-06-15 12:07 2 157 T310C1NO.HID 3 File(s) 399 006 bytes Total Files Listed: 104 File(s) 391 625 352 bytes 42 Dir(s) 0 bytes free S:\> Now which line or lines need to be changed? Do I really have to change drive letter Z: to C:? Proposed solutions Solution #1 Ramhound proposed to change the boot order to following; CD-ROM, IDE-0, Floppy This didn't help. In fact, here is the result of it. Searching for Boot Record from CDROM..Not Found Searching for Boot Record from IDE-0.. OK Missing operating system Any other ideas?... Solution #2 Rik proposed to run Z:\setup. Now that I have found a way to drop to DOS prompt with Ctrl+C as described above (Update 2), I did try running setup but there is no such command or file in there. So that didn't work.

  Read the article

• Failure retrieving contents of directory

  - by Bondye

  Currently I have a couple of websites. My problem is that if I login on 1 specific domain with any of my programs (using notepadd++, FileZilla and Netbeans) the program stops at the content listing. I had it correctly running, (I'm working on a project on this domain for more than a year now) and suddenly I broke it somehow. This only happens on 1 specific domain, all other domains (from other hosts) are working. My colleague (next to me with same ip address) is able to login on this domain. Notepadd++ says: Failure retrieving contents of directory Filezilla says: Failed to retrieve directory listing Netbean popups: Upload files on save failed. (Because I have the setting upload on save enabled.) What I tried: First I thought it's my firewall, I disabled firewall but no result. Also notice that all other domain are working. Maby a blacklist with my ip address? No my colleague has the same ip address. Could anyone help me on this? Notepad++ Log [NppFTP] Everything initialized -> TYPE I Connecting -> Quit 220 ProFTPD 1.3.3e Server ready. -> USER username 331 Password required for domain -> PASS *HIDDEN* 230 User username logged in -> TYPE A 200 Type set to A -> MODE S 200 Mode set to S -> STRU F 200 Structure set to F -> CWD /domains/domain.nl/ 250 CWD command successful Connected -> CWD /domains/domain.nl/ 250 CWD command successful -> PASV 227 Entering Passive Mode (194,247,31,xx,137,xx). -> LIST -al Failure retrieving contents of directory /domains/domain.nl/ Filezilla log Status: Verbinden met 194.247.xx.xx:21... Status: Verbinding aangemaakt, welkomstbericht afwachten... Antwoord: 220 ProFTPD 1.3.3e Server ready. Commando: USER username Antwoord: 331 Password required for username Commando: PASS ******** Antwoord: 230 User username logged in Commando: SYST Antwoord: 215 UNIX Type: L8 Commando: FEAT Antwoord: 211-Features: Antwoord: MDTM Antwoord: MFMT Antwoord: LANG en-US;ja-JP;zh-TW;it-IT;fr-FR;zh-CN;ru-RU;bg-BG;ko-KR Antwoord: TVFS Antwoord: UTF8 Antwoord: AUTH TLS Antwoord: MFF modify;UNIX.group;UNIX.mode; Antwoord: MLST modify*;perm*;size*;type*;unique*;UNIX.group*;UNIX.mode*;UNIX.owner*; Antwoord: PBSZ Antwoord: PROT Antwoord: REST STREAM Antwoord: SIZE Antwoord: 211 End Commando: OPTS UTF8 ON Antwoord: 200 UTF8 set to on Status: Verbonden Status: Mappenlijst ophalen... Commando: PWD Antwoord: 257 "/" is the current directory Commando: TYPE I Antwoord: 200 Type set to I Commando: PASV Antwoord: 227 Entering Passive Mode (194,247,31,xx,xxx,xx). Commando: MLSD Fout: Verbinding verloren Fout: Ontvangen van mappenlijst is mislukt Sorry that it's dutch.

  Read the article

• MAAS nodes stuck on "maas-enlisting-node"

  - by CyberJacob

  I am trying to set up an MAAS cluster, but am having some issues adding nodes. The nodes boot up from the TFTP server on the master server, display a login screen (with the hostname "maas-enlisting-node") and stop. I cannot log in with ubuntu/ubuntu or with my SSH keys. The MAAS server is running DHCP and DNS on the network, and the TFTP boot appears to be loading everything without issues (I can screencap if you want) Any ideas what's going wrong? Thanks!

  Read the article

• Add keyboard languages to XP, Vista, and Windows 7

  - by Matthew Guay

  Do you regularly need to type in multiple languages in Windows?  Here we’ll show you the easy way to add and change input languages to your keyboard in XP, Vista, and Windows 7. Windows Vista and 7 come preinstalled with support for viewing a wide variety of languages, so adding an input language is fairly simply.  Adding an input language is slightly more difficult in XP, and requires installing additional files if you need an Asian or Complex script language.  First we show how to add an input language in Windows Vista and 7; it’s basically the same in both versions.  Then, we show how to add a language to XP, and also how to add Complex Script support.  Please note that this is only for adding an input language, which will allow you to type in the language you select.  This does not change your user interface language. Change keyboard language in Windows 7 and Vista It is fairly simple to add or change a keyboard language in Windows 7 or Vista.  In Windows 7, enter “keyboard language” in the Start menu search box, and select “Change keyboards or other input methods”. In Windows Vista, open Control Panel and enter “input language” in the search box and select “Change keyboards or other input methods”.  This also works in Windows 7. Now, click Change Keyboards to add another keyboard language or change your default one. Our default input language is US English, and our default keyboard is the US keyboard layout.  Click Add to insert another input language while still leaving your default input language installed. Here we selected the standard Thai keyboard language (Thai Kedmanee), but you can select any language you want.  Windows offers almost any language you can imagine, so just look for the language you want, select it, and click Ok. Alternately, if you want, you can click Preview to see your layout choice before accepting it.  This is only the default characters, not ones that will be activated with Shift or other keys (many Asian languages use many more characters than English, and require the use of Shift and other keys to access them all).  Once your finished previewing, click close and then press Ok on the previous dialog. Now you will see both of your keyboard languages in the Installed services box.  You can click Add to go back and get more, or move your selected language up or down (to change its priority), or simply click Apply to add the new language. Also, you can now change the default input language from the top menu.  This is the language that your keyboard will start with when you boot your computer.  So, if you mainly use English but also use another language, usually it is best to leave English as your default input language. Once you’ve pressed Apply or Ok, you will see a new icon beside your system tray with the initials of your default input language. If you click it, you can switch between input languages.  Alternately you can switch input languages by pressing Alt+Shift on your keyboard. Some complex languages, such as Chinese, may have extra buttons to change input modes to accommodate their large alphabet. If you would like to change the keyboard shortcut for changing languages, go back to the Input Languages dialog, and select the “Advanced Key Settings” tab.  Here you can change settings for Caps Lock and change or add key sequences to change between languages. Also, the On-Screen keyboard will display the correct keyboard language (here the keyboard is displaying Thai), which can be a helpful reference if your physical keyboard doesn’t have your preferred input language printed on it.  To open this, simply enter “On-Screen keyboard” in the start menu search, or click All Programs>Accessories>On-Screen keyboard. Change keyboard language in Windows XP The process for changing the keyboard language in Windows XP is slightly different.  Open Control Panel, and select “Date, Time, Language, and Regional Options”.   Select “Add other languages”. Now, click Details to add another language.  XP does not include support for Asian and complex languages by default, so if you need to add one of those languages we have details for that below. Click Add to add an input language. Select your desired language from the list, and choose your desired keyboard layout if your language offers multiple layouts.  Here we selected Canadian French with the default layout. Now you will see both of your keyboard languages in the Installed services box.  You can click Add to go back and add more, or move your selected language up or down (to change its priority), or simply click Apply to add the new language. Once you’ve pressed Apply or Ok, you will see a new icon beside your system tray with the initials of your default input language. If you click it, you can switch between input languages.  Alternately you can switch input languages by pressing Alt+Shift on your keyboard. If you would like to change the keyboard shortcut for changing languages, go back to the Input Languages dialog, and click the “Key Settings” button on the bottom of the dialog.  Here you can change settings for Caps Lock and change or add key sequences to change between languages. Add support to XP for Asian and Complex script languages Windows XP does not include support for Asian and Complex script languages by default, but you can easily add them to your computer.  This is useful if you wish to type in one of these languages, or simply want to read text written in these languages, since XP will not display these languages correctly if they are not installed.  If you wish to install Chinese, Japanese, and/or Korean, check the “Install files for East Asian languages” box.  Or, if you need to install a complex script language (including Arabic, Armenian, Georgian, Hebrew, the Indic languages, Thai, and Vietnamese), check the “Install files for complex script and right-to-left languages” box.   Choosing either of these options will open a prompt reminding you that this option will take up more disk space.  Support for complex languages will require around 10Mb of hard drive space, but East Asian language support may require 230 Mb or more free disk space.  Click Ok, and click apply to install your language files. You may have to insert your XP CD into your CD drive to install these files.  Insert the disk, and then click Ok. Windows will automatically copy the files, including fonts for these languages… …and then will ask you to reboot your computer to finalize the settings.  Click Yes, and then reopen the “Add other languages” dialog when your computer is rebooted, and add a language as before.     Now you can add Complex and/or Asian languages to XP, just as above.  Here is the XP taskbar language selector with Thai installed. Conclusion Unfortunately we haven’t found a way to add Asian and complex languages in XP without having an XP disc. If you know of a way, let us know in the comments. (No downloading the XP disc from torrent site answers please) Adding an input language is very important for bilingual individuals, and can also be useful if you simply need to occasionally view Asian or Complex languages in XP.  And by following the correct instructions for your version of Windows, it should be very easy to add, change, and remove input languages. Similar Articles Productive Geek Tips Show Keyboard Shortcut Access Keys in Windows VistaKeyboard Ninja: 21 Keyboard Shortcut ArticlesAnother Desktop Cube for Windows XP/VistaThe "Up" Keyboard Shortcut for Windows 7 or Vista ExplorerWhat is ctfmon.exe And Why Is It Running? TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Make your Joomla & Drupal Sites Mobile with OSMOBI Integrate Twitter and Delicious and Make Life Easier Design Your Web Pages Using the Golden Ratio Worldwide Growth of the Internet How to Find Your Mac Address Use My TextTools to Edit and Organize Text

  Read the article

< Previous Page | 490 491 492 493 494 495 496 497 498 499 500 501  | Next Page >