Search Results

Search found 12676 results on 508 pages for 'virtual directories'.

Page 495/508 | < Previous Page | 491 492 493 494 495 496 497 498 499 500 501 502  | Next Page >

• Site-to-Site PPTP VPN connection between two Windows Server 2008 R2 servers

  - by steve_eyre

  We have two Windows Server 2008 R2 machines, one in our main office and one in a new office which we have just moved offsite. The main office has previously been handling client-to-server PPTP VPN connections. Now that we have moved our second server out of office, we want to set up a demand-dial or persistent VPN connection from the second server to the primary. Using a custom setting RRAS profile, we have successfully managed to set up a site-to-site VPN connection so that from the second server itself, it can access any of the devices in the main office and communicate back. However, any connected machines in the second office cannot use this connection, even when using the second server as gateway. The demand-dial interface is setup from the Second Server dialing into Main Server and a static route set up on RRAS for 192.168.0.0 with subnet mask 255.255.0.0 pointing down this network interface. The main office has the network of 192.168.0.0/16 (subnet mask 255.255.0.0). The second office has the network of 172.16.100.0/24 (subnet mask 255.255.255.0). What steps do we need to take to ensure traffic from the second office PCs going towards 192.168.x.x addresses use the VPN route? Many Thanks in advance for any help the community can offer. Debug Information Here is the route print output from the second server: =========================================================================== Interface List 23...........................Main Office 22...........................RAS (Dial In) Interface 16...e0 db 55 12 fa 02 ......Local Area Connection - Virtual Network 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 14...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 24...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.16.100.250 172.16.100.222 261 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 <MAIN OFFICE IP> 255.255.255.255 172.16.100.250 172.16.100.222 6 172.16.100.0 255.255.255.0 On-link 172.16.100.222 261 172.16.100.113 255.255.255.255 On-link 172.16.100.113 306 172.16.100.222 255.255.255.255 On-link 172.16.100.222 261 172.16.100.223 255.255.255.255 On-link 172.16.100.222 261 172.16.100.224 255.255.255.255 On-link 172.16.100.222 261 172.16.100.225 255.255.255.255 On-link 172.16.100.222 261 172.16.100.226 255.255.255.255 On-link 172.16.100.222 261 172.16.100.227 255.255.255.255 On-link 172.16.100.222 261 172.16.100.228 255.255.255.255 On-link 172.16.100.222 261 172.16.100.229 255.255.255.255 On-link 172.16.100.222 261 172.16.100.230 255.255.255.255 On-link 172.16.100.222 261 172.16.100.255 255.255.255.255 On-link 172.16.100.222 261 192.168.0.0 255.255.0.0 192.168.101.87 192.168.101.17 266 192.168.101.17 255.255.255.255 On-link 192.168.101.17 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.16.100.222 261 224.0.0.0 240.0.0.0 On-link 172.16.100.113 306 224.0.0.0 240.0.0.0 On-link 192.168.101.17 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 172.16.100.222 261 255.255.255.255 255.255.255.255 On-link 172.16.100.113 306 255.255.255.255 255.255.255.255 On-link 192.168.101.17 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.0.200 Default 0.0.0.0 0.0.0.0 172.16.100.250 Default =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 16 261 fe80::/64 On-link 16 261 fe80::edf4:85c6:3c15:dcbe/128 On-link 1 306 ff00::/8 On-link 16 261 ff00::/8 On-link 22 306 ff00::/8 On-link =========================================================================== Persistent Routes: None And here is the route print from one of the second office PCs: =========================================================================== Interface List 11...10 78 d2 32 53 27 ......Atheros AR8151 PCI-E Gigabit Ethernet Controller 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.16.100.250 172.16.100.103 10 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 172.16.100.0 255.255.255.0 On-link 172.16.100.103 266 172.16.100.103 255.255.255.255 On-link 172.16.100.103 266 172.16.100.255 255.255.255.255 On-link 172.16.100.103 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.16.100.103 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 172.16.100.103 266 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 11 266 fe80::/64 On-link 11 266 fe80::e973:de17:a045:aa78/128 On-link 1 306 ff00::/8 On-link 11 266 ff00::/8 On-link =========================================================================== Persistent Routes: None

  Read the article

• php crashes with no core file and this message : apc_mmap failed

  - by greg0ire

  Description of the problem Regularly, cron php processes crash on our production server, which result in mails with the following body : PHP Fatal error: PHP Startup: apc_mmap: mmap failed: in Unknown on line 0 Segmentation fault (core dumped) I think the Segmentation fault (core dumped) should result in core files being handled by apport and then written in /var/crashes, but the files I can see there are there since yesterday, although the last crash occured today : -rw-r----- 1 root whoopsie 1138528 mai 22 04:09 _usr_bin_php5.0.crash -rw-r----- 1 frontoffice whoopsie 1166373 mai 20 18:00 _usr_bin_php5.1005.crash -rw-r----- 1 frontoffice whoopsie 81622658 mai 22 00:05 _usr_sbin_php5-fpm.1005.crash I tried to download the last one anyway, and ran gdb /usr/sbin/php5-fpm /tmp/_usr_sbin_php5-fpm.1005.crash, only to be told that the file is not a core file (its format was not recognized). Here is the server's apc configuration : cat /etc/php5/cli/conf.d/20-apc.ini extension=apc.so apc.shm_size=512M apc.ttl=3600 apc.user_ttl=3600 apc.enable_cli=1 I'm mostly worried about the apc.shm_size… isn't it too high or too low ? I understand it has to do with the size of memory segments. Question(s) What could be the problem ? How can I troubleshoot it (how can I get a valid core file ?) ? System information free total used free shared buffers cached Mem: 5081296 4354684 726612 0 374744 959968 -/+ buffers/cache: 3019972 2061324 Swap: 522236 516888 5348 cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.2 LTS" php -v PHP 5.4.17-1~precise+1 (cli) (built: Jul 17 2013 18:14:06) Copyright (c) 1997-2013 The PHP Group Zend Engine v2.4.0, Copyright (c) 1998-2013 Zend Technologies php -i excerpt : Configuration apc APC Support => enabled Version => 3.1.13 APC Debugging => Disabled MMAP Support => Enabled MMAP File Mask => Locking type => pthread mutex Locks Serialization Support => php Revision => $Revision: 327136 $ Build Date => Nov 20 2012 18:41:36 Directive => Local Value => Master Value apc.cache_by_default => On => On apc.canonicalize => On => On apc.coredump_unmap => Off => Off apc.enable_cli => On => On apc.enabled => On => On apc.file_md5 => Off => Off apc.file_update_protection => 2 => 2 apc.filters => no value => no value apc.gc_ttl => 3600 => 3600 apc.include_once_override => Off => Off apc.lazy_classes => Off => Off apc.lazy_functions => Off => Off apc.max_file_size => 1M => 1M apc.mmap_file_mask => no value => no value apc.num_files_hint => 1000 => 1000 apc.preload_path => no value => no value apc.report_autofilter => Off => Off apc.rfc1867 => Off => Off apc.rfc1867_freq => 0 => 0 apc.rfc1867_name => APC_UPLOAD_PROGRESS => APC_UPLOAD_PROGRESS apc.rfc1867_prefix => upload_ => upload_ apc.rfc1867_ttl => 3600 => 3600 apc.serializer => default => default apc.shm_segments => 1 => 1 apc.shm_size => 512M => 512M apc.shm_strings_buffer => 4M => 4M apc.slam_defense => On => On apc.stat => On => On apc.stat_ctime => Off => Off apc.ttl => 3600 => 3600 apc.use_request_time => On => On apc.user_entries_hint => 4096 => 4096 apc.user_ttl => 3600 => 3600 apc.write_lock => On => On php -m [PHP Modules] apc bcmath bz2 calendar Core ctype curl date dba dom ereg exif fileinfo filter ftp gd gettext hash iconv imagick intl json ldap libxml mbstring memcache memcached mhash mysql mysqli openssl pcntl pcre PDO pdo_mysql pdo_pgsql pdo_sqlite pgsql Phar posix Reflection session shmop SimpleXML soap sockets SPL sqlite3 standard sysvmsg sysvsem sysvshm tidy tokenizer wddx xml xmlreader xmlwriter zip zlib [Zend Modules] ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 39531 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) 39531 virtual memory (kbytes, -v) unlimited file locks (-x) unlimited

  Read the article

• vSphere ESX 5.5 hosts cannot connect to NFS Server

  - by Gerald

  Summary: My problem is I cannot use the QNAP NFS Server as an NFS datastore from my ESX hosts despite the hosts being able to ping it. I'm utilising a vDS with LACP uplinks for all my network traffic (including NFS) and a subnet for each vmkernel adapter. Setup: I'm evaluating vSphere and I've got two vSphere ESX 5.5 hosts (node1 and node2) and each one has 4x NICs. I've teamed them all up using LACP/802.3ad with my switch and then created a distributed switch between the two hosts with each host's LAG as the uplink. All my networking is going through the distributed switch, ideally, I want to take advantage of DRS and the redundancy. I have a domain controller VM ("Central") and vCenter VM ("vCenter") running on node1 (using node1's local datastore) with both hosts attached to the vCenter instance. Both hosts are in a vCenter datacenter and a cluster with HA and DRS currently disabled. I have a QNAP TS-669 Pro (Version 4.0.3) (TS-x69 series is on VMware Storage HCL) which I want to use as the NFS server for my NFS datastore, it has 2x NICs teamed together using 802.3ad with my switch. vmkernel.log: The error from the host's vmkernel.log is not very useful: NFS: 157: Command: (mount) Server: (10.1.2.100) IP: (10.1.2.100) Path: (/VM) Label (datastoreNAS) Options: (None) cpu9:67402)StorageApdHandler: 698: APD Handle 509bc29f-13556457 Created with lock[StorageApd0x411121] cpu10:67402)StorageApdHandler: 745: Freeing APD Handle [509bc29f-13556457] cpu10:67402)StorageApdHandler: 808: APD Handle freed! cpu10:67402)NFS: 168: NFS mount 10.1.2.100:/VM failed: Unable to connect to NFS server. Network Setup: Here is my distributed switch setup (JPG). Here are my networks. 10.1.1.0/24 VM Management (VLAN 11) 10.1.2.0/24 Storage Network (NFS, VLAN 12) 10.1.3.0/24 VM vMotion (VLAN 13) 10.1.4.0/24 VM Fault Tolerance (VLAN 14) 10.2.0.0/24 VM's Network (VLAN 20) vSphere addresses 10.1.1.1 node1 Management 10.1.1.2 node2 Management 10.1.2.1 node1 vmkernel (For NFS) 10.1.2.2 node2 vmkernel (For NFS) etc. Other addresses 10.1.2.100 QNAP TS-669 (NFS Server) 10.2.0.1 Domain Controller (VM on node1) 10.2.0.2 vCenter (VM on node1) I'm using a Cisco SRW2024P Layer-2 switch (Jumboframes enabled) with the following setup: LACP LAG1 for node1 (Ports 1 through 4) setup as VLAN trunk for VLANs 11-14,20 LACP LAG2 for my router (Ports 5 through 8) setup as VLAN trunk for VLANs 11-14,20 LACP LAG3 for node2 (Ports 9 through 12) setup as VLAN trunk for VLANs 11-14,20 LACP LAG4 for the QNAP (Ports 23 and 24) setup to accept untagged traffic into VLAN 12 Each subnet is routable to another, although, connections to the NFS server from vmk1 shouldn't need it. All other traffic (vSphere Web Client, RDP etc.) goes through this setup fine. I tested the QNAP NFS server beforehand using ESX host VMs atop of a VMware Workstation setup with a dedicated physical NIC and it had no problems. The ACL on the NFS Server share is permissive and allows all subnet ranges full access to the share. I can ping the QNAP from node1 vmk1, the adapter that should be used to NFS: ~ # vmkping -I vmk1 10.1.2.100 PING 10.1.2.100 (10.1.2.100): 56 data bytes 64 bytes from 10.1.2.100: icmp_seq=0 ttl=64 time=0.371 ms 64 bytes from 10.1.2.100: icmp_seq=1 ttl=64 time=0.161 ms 64 bytes from 10.1.2.100: icmp_seq=2 ttl=64 time=0.241 ms Netcat does not throw an error: ~ # nc -z 10.1.2.100 2049 Connection to 10.1.2.100 2049 port [tcp/nfs] succeeded! The routing table of node1: ~ # esxcfg-route -l VMkernel Routes: Network Netmask Gateway Interface 10.1.1.0 255.255.255.0 Local Subnet vmk0 10.1.2.0 255.255.255.0 Local Subnet vmk1 10.1.3.0 255.255.255.0 Local Subnet vmk2 10.1.4.0 255.255.255.0 Local Subnet vmk3 default 0.0.0.0 10.1.1.254 vmk0 VM Kernel NIC info ~ # esxcfg-vmknic -l Interface Port Group/DVPort IP Family IP Address Netmask Broadcast MAC Address MTU TSO MSS Enabled Type vmk0 133 IPv4 10.1.1.1 255.255.255.0 10.1.1.255 00:50:56:66:8e:5f 1500 65535 true STATIC vmk0 133 IPv6 fe80::250:56ff:fe66:8e5f 64 00:50:56:66:8e:5f 1500 65535 true STATIC, PREFERRED vmk1 164 IPv4 10.1.2.1 255.255.255.0 10.1.2.255 00:50:56:68:f5:1f 1500 65535 true STATIC vmk1 164 IPv6 fe80::250:56ff:fe68:f51f 64 00:50:56:68:f5:1f 1500 65535 true STATIC, PREFERRED vmk2 196 IPv4 10.1.3.1 255.255.255.0 10.1.3.255 00:50:56:66:18:95 1500 65535 true STATIC vmk2 196 IPv6 fe80::250:56ff:fe66:1895 64 00:50:56:66:18:95 1500 65535 true STATIC, PREFERRED vmk3 228 IPv4 10.1.4.1 255.255.255.0 10.1.4.255 00:50:56:72:e6:ca 1500 65535 true STATIC vmk3 228 IPv6 fe80::250:56ff:fe72:e6ca 64 00:50:56:72:e6:ca 1500 65535 true STATIC, PREFERRED Things I've tried/checked: I'm not using DNS names to connect to the NFS server. Checked MTU. Set to 9000 for vmk1, dvSwitch and Cisco switch and QNAP. Moved QNAP onto VLAN 11 (VM Management, vmk0) and gave it an appropriate address, still had same issue. Changed back afterwards of course. Tried initiating the connection of NAS datastore from vSphere Client (Connected to vCenter or directly to host), vSphere Web Client and the host's ESX Shell. All resulted in the same problem. Tried a path name of "VM", "/VM" and "/share/VM" despite not even having a connection to server. I plugged in a linux system (10.1.2.123) into a switch port configured for VLAN 12 and tried mounting the NFS share 10.1.2.100:/VM, it worked successfully and I had read-write access to it I tried disabling the firewall on the ESX host esxcli network firewall set --enabled false I'm out of ideas on what to try next. The things I'm doing differently from my VMware Workstation setup is the use of LACP with a physical switch and a virtual distributed switch between the two hosts. I'm guessing the vDS is probably the source of my troubles but I don't know how to fix this problem without eliminating it.

  Read the article

• Unusually high memory usage on a CentOS VPS with 512 guaranteed RAM

  - by Andrei Bârsan

  I'm working on a medium-sized web application written in PHP that's running on a VPS with 512mb ram. The webapp hasn't been officially launched yet, so there isn't too much traffic going on, just me and a few other people working on it. There is another slightly smaller webapp also hosted on this machine, among 4-5 other small static sites. We are running Centos 5 32-bit & cPanel/WHM. This is the result of running ps aux and, as you can see, it's not using 100% of the RAM. However, on the hypanel overview, it's always shown as using aroun 500MB ram, just for running apache, mysql, and the lowest-memory-footprint versions of the mail server, ftp server etc. -bash-3.2# ps aux USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 1 0.0 0.0 2156 664 ? Ss 12:08 0:00 init [3] root 1123 0.0 0.0 2260 548 ? S<s 12:08 0:00 /sbin/udevd -d root 1462 0.0 0.0 1812 568 ? Ss 12:08 0:00 syslogd -m 0 named 1496 0.0 0.0 3808 820 ? Ss 12:08 0:00 nsd named 1497 0.0 0.0 10672 756 ? S 12:08 0:00 nsd named 1499 0.0 0.0 3880 584 ? S 12:08 0:00 nsd root 1514 0.0 0.1 7240 1064 ? Ss 12:08 0:00 /usr/sbin/sshd root 1522 0.0 0.0 2832 832 ? Ss 12:08 0:00 xinetd -stayalive -pidfile /var/run/xinetd.pid root 1534 0.0 0.1 3712 1328 ? S 12:08 0:00 /bin/sh /usr/bin/mysqld_safe --datadir=/var/lib/mysql - mysql 1667 0.0 2.9 225680 30884 ? Sl 12:08 0:00 /usr/sbin/mysqld --basedir=/ --datadir=/var/lib/mysql - mailnull 1766 0.0 0.1 9352 1100 ? Ss 12:08 0:00 /usr/sbin/exim -bd -q60m root 1797 0.0 0.0 2156 708 ? Ss 12:08 0:00 /usr/sbin/dovecot root 1798 0.0 0.0 2632 1012 ? S 12:08 0:00 dovecot-auth root 1816 0.0 3.0 38580 32456 ? Ss 12:08 0:01 /usr/local/bin/spamd -d --allowed-ips=127.0.0.1 --pidfi root 1839 0.0 1.6 63200 17496 ? Ss 12:08 0:00 /usr/local/apache/bin/httpd -k start -DSSL root 1846 0.0 0.1 5416 1468 ? Ss 12:08 0:00 pure-ftpd (SERVER) root 1848 0.0 0.1 6212 1244 ? S 12:08 0:00 /usr/sbin/pure-authd -s /var/run/ftpd.sock -r /usr/sbin root 1856 0.0 0.1 4492 1112 ? Ss 12:08 0:00 crond root 1864 0.0 0.0 2356 428 ? Ss 12:08 0:00 /usr/sbin/atd dovecot 1927 0.0 0.1 5196 1952 ? S 12:08 0:00 pop3-login dovecot 1928 0.0 0.1 5196 1948 ? S 12:08 0:00 pop3-login dovecot 1929 0.0 0.1 5316 2012 ? S 12:08 0:00 imap-login dovecot 1930 0.0 0.2 5416 2228 ? S 12:08 0:00 imap-login root 1939 0.0 0.1 3936 1964 ? S 12:08 0:00 cPhulkd - processor root 1963 0.0 0.8 15876 8564 ? S 12:08 0:00 cpsrvd (SSL) - waiting for connections root 1966 0.0 0.7 15172 7748 ? S 12:08 0:00 cpdavd - accepting connections on 2077 and 2078 root 1990 0.0 0.2 5008 3136 ? S 12:08 0:00 queueprocd - wait to process a task root 2017 0.0 2.9 38580 31020 ? S 12:08 0:00 spamd child root 2018 0.0 0.5 8904 5636 ? S 12:08 0:00 /usr/bin/perl /usr/local/cpanel/bin/leechprotect nobody 2021 0.0 3.2 66512 33724 ? S 12:08 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 2022 0.0 3.1 67812 33024 ? S 12:08 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 2024 0.0 1.9 64364 20680 ? S 12:08 0:00 /usr/local/apache/bin/httpd -k start -DSSL root 2027 0.0 0.4 9000 4540 ? S 12:08 0:00 tailwatchd root 2032 0.0 0.1 4176 1836 ? SN 12:08 0:00 cpanellogd - sleeping for logs nobody 3096 0.0 1.9 64572 20264 ? S 12:09 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 3097 0.0 2.8 66008 30136 ? S 12:09 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 3098 0.0 2.8 65704 29752 ? S 12:09 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 3099 0.0 3.1 67260 32816 ? S 12:09 0:00 /usr/local/apache/bin/httpd -k start -DSSL andrei 3448 0.0 0.1 3204 1632 ? S 12:50 0:00 imap nobody 3537 0.0 1.9 64308 20108 ? S 13:01 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 3614 0.0 1.9 64576 20628 ? S 13:10 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 3615 0.0 1.3 63200 14672 ? S 13:10 0:00 /usr/local/apache/bin/httpd -k start -DSSL root 3626 0.0 0.2 10232 2964 ? Rs 13:14 0:00 sshd: root@pts/0 root 3648 0.0 0.1 3844 1600 pts/0 Ss 13:14 0:00 -bash root 3826 0.0 0.0 2532 908 pts/0 R+ 13:21 0:00 ps aux Lately, without any significant changes to the configuration, the memory usage started peaking and going over 512, causing the virtual server to kill apache, basically murdering our site in the process. Do you have any idea if this is normal and more resources should be acquired? I don't think... since there isn't too much data or traffic online yet.

  Read the article

• Weird routing issue (updated)

  - by smccloud

  I just updated the route tables due to a mistake on my part. I am working on getting networking working correctly on a cluster of 14 virtual servers at a customer site. 11 of them work fine for routing and 3 don't work correctly for their administrative network (172.28.56.0). All are running Windows Web Server 2008R2. Default gateway is set on the production network (172.28.58.0) and not on the administrative network (handled with persistent static routes). On a working server, route print gives me the following (MACs redacted) =========================================================================== Interface List 11...XX XX XX XX XX XX ......Intel(R) PRO/1000 MT Network Connection 13...XX XX XX XX XX XX00 0c 29 85 b2 98 ......Intel(R) PRO/1000 MT Network Connection #2 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 14...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 15...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.28.58.1 172.28.58.11 266 10.18.1.22 255.255.255.255 172.28.58.1 172.28.58.11 11 10.32.0.0 255.255.0.0 172.28.56.1 172.28.56.201 11 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 172.28.34.0 255.255.255.0 172.28.56.1 172.28.56.201 11 172.28.42.0 255.255.255.0 172.28.56.1 172.28.56.201 11 172.28.56.0 255.255.255.0 On-link 172.28.56.201 266 172.28.56.0 255.255.255.0 172.28.56.1 172.28.56.201 11 172.28.56.201 255.255.255.255 On-link 172.28.56.201 266 172.28.56.255 255.255.255.255 On-link 172.28.56.201 266 172.28.58.0 255.255.255.224 On-link 172.28.58.11 266 172.28.58.0 255.255.255.224 172.28.58.1 172.28.58.11 11 172.28.58.1 255.255.255.255 172.28.58.1 172.28.58.11 11 172.28.58.11 255.255.255.255 On-link 172.28.58.11 266 172.28.58.31 255.255.255.255 On-link 172.28.58.11 266 172.28.60.0 255.255.255.0 172.28.56.1 172.28.56.201 11 172.28.63.0 255.255.255.0 172.28.56.1 172.28.56.201 11 192.168.0.0 255.255.0.0 172.28.56.1 172.28.56.201 11 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.28.56.201 266 224.0.0.0 240.0.0.0 On-link 172.28.58.11 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 172.28.56.201 266 255.255.255.255 255.255.255.255 On-link 172.28.58.11 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 172.28.56.0 255.255.255.0 172.28.56.1 1 172.28.63.0 255.255.255.0 172.28.56.1 1 192.168.0.0 255.255.0.0 172.28.56.1 1 172.28.60.0 255.255.255.0 172.28.56.1 1 10.32.0.0 255.255.0.0 172.28.56.1 1 172.28.34.0 255.255.255.0 172.28.56.1 1 172.28.42.0 255.255.255.0 172.28.56.1 1 0.0.0.0 0.0.0.0 172.28.58.1 Default =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None On one of the non-working server, route print gives me the following (MACs redacted) =========================================================================== Interface List 11...XX XX XX XX XX XX ......Intel(R) PRO/1000 MT Network Connection 13...XX XX XX XX XX XX ......Intel(R) PRO/1000 MT Network Connection #2 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 14...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 16...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.28.58.1 172.28.58.21 266 10.32.0.0 255.255.0.0 172.28.56.1 172.28.56.211 11 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 172.28.34.0 255.255.255.0 172.28.56.1 172.28.56.211 11 172.28.42.0 255.255.255.0 172.28.56.1 172.28.56.211 11 172.28.56.0 255.255.255.0 172.28.56.1 172.28.56.211 11 172.28.56.211 255.255.255.255 On-link 172.28.56.211 266 172.28.58.0 255.255.255.0 172.28.58.1 172.28.58.21 11 172.28.58.0 255.255.255.224 On-link 172.28.58.21 266 172.28.58.21 255.255.255.255 On-link 172.28.58.21 266 172.28.58.31 255.255.255.255 On-link 172.28.58.21 266 172.28.60.0 255.255.255.0 172.28.56.1 172.28.56.211 11 172.28.63.0 255.255.255.0 172.28.56.1 172.28.56.211 11 192.168.0.0 255.255.0.0 172.28.56.1 172.28.56.211 11 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.28.56.211 266 224.0.0.0 240.0.0.0 On-link 172.28.58.21 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 06 255.255.255.255 255.255.255.255 On-link 172.28.56.211 266 255.255.255.255 255.255.255.255 On-link 172.28.58.21 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 172.28.56.0 255.255.255.0 172.28.56.1 1 172.28.60.0 255.255.255.0 172.28.56.1 1 172.28.63.0 255.255.255.0 172.28.56.1 1 172.28.34.0 255.255.255.0 172.28.56.1 1 172.28.42.0 255.255.255.0 172.28.56.1 1 192.168.0.0 255.255.0.0 172.28.56.1 1 10.32.0.0 255.255.0.0 172.28.56.1 1 0.0.0.0 0.0.0.0 172.28.58.1 Default 172.28.58.0 255.255.255.0 172.28.58.1 1 =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None I am at a complete loss why the non-working servers have no On-link route for 172.28.56.0. Does anyone have any suggestions on what I should be looking at to figure this out? Also, I do have "physical" access to the console if needed through vSphere Client.

  Read the article

• Can't deploy rails 4 app on Bluehost with Passenger 4 and nginx

  - by user2205763

  I am at Bluehost (dedicated server) trying to run a rails 4 app. I asked to have my server re-imaged, specifying that I do not want rails, ruby, or passenger install automatically as I wanted to install the latest versions myself using a version manager (Bluehost by default offers rails 2.3, ruby 1.8, and passenger 3, which won't work with my app). I installed ruby 1.9.3p327, rails 4.0.0, and passenger 4.0.5. I can verify this by typing, "ruby -v", "rails -v", and "passenger -v" (also "gem -v"). I made sure to install these not as root, so that I don't get a 403 forbidden error when trying to deploy the app. I installed passenger by typing "gem install passenger", and then installed the nginx passenger module (into "/nginx") with "passenger-install-nginx-module". I am trying to run my rails app on a subdomain, http://development.thegraduate.hk (I am using the subdomain to show my client progress on the website). In bluehost I created that subdomain, and had it point to "public_html/thegraduate". I then created a symlink from "rails_apps/thegraduate/public" to "public_html/thegraduate" and verified that the symlink exists. The problem is: when I go to http://development.thegraduate.hk, I get a directory listing. There is nothing resembling a rails app. I have not added a .htaccess file to /rails_apps/thegraduate/public, as that was never specified in the installation of passenger. It was meant to be 'install and go'. When I type "passenger-memory-status", I get 3 things: - Apache processes (7) - Nginx processes (0) - Passenger processes (0) So it appears that nginx and passenger are not running, and I can't figure out how to get it to run (I'm not looking to have it run as a standalone server). Here is my nginx.conf file (/nginx/conf/nginx.conf): #user nobody; worker_processes 1; #error_log logs/error.log; #error_log logs/error.log notice; #error_log logs/error.log info; #pid logs/nginx.pid; events { worker_connections 1024; } http { passenger_root /home/thegrad4/.rbenv/versions/1.9.3-p327/lib/ruby/gems/1.9.1/gems/passenger-4.0.5; passenger_ruby /home/thegrad4/.rbenv/versions/1.9.3-p327/bin/ruby; include mime.types; default_type application/octet-stream; #log_format main '$remote_addr - $remote_user [$time_local] "$request" ' # '$status $body_bytes_sent "$http_referer" ' # '"$http_user_agent" "$http_x_forwarded_for"'; #access_log logs/access.log main; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; #gzip on; server { listen 80; server_name development.thegraduate.hk; root ~/rails_apps/thegraduate/public; passenger_enabled on; #charset koi8-r; #access_log logs/host.access.log main; location / { root html; index index.html index.htm; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } # proxy the PHP scripts to Apache listening on 127.0.0.1:80 # #location ~ \.php$ { # proxy_pass http://127.0.0.1; #} # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # #location ~ \.php$ { # root html; # fastcgi_pass 127.0.0.1:9000; # fastcgi_index index.php; # fastcgi_param SCRIPT_FILENAME /scripts$fastcgi_script_name; # include fastcgi_params; #} # deny access to .htaccess files, if Apache's document root # concurs with nginx's one # #location ~ /\.ht { # deny all; #} } # another virtual host using mix of IP-, name-, and port-based configuration # #server { # listen 8000; # listen somename:8080; # server_name somename alias another.alias; # location / { # root html; # index index.html index.htm; # } #} # HTTPS server # #server { # listen 443; # server_name localhost; # ssl on; # ssl_certificate cert.pem; # ssl_certificate_key cert.key; # ssl_session_timeout 5m; # ssl_protocols SSLv2 SSLv3 TLSv1; # ssl_ciphers HIGH:!aNULL:!MD5; # ssl_prefer_server_ciphers on; # location / { # root html; # index index.html index.htm; # } #} } I don't get any errors, just the directory listing. I've tried to be as detailed as possible. Any help on this issue would be greatly appreciated as I've been stumped for the past 3 days. Scouring the web has not helped as my issue seems to be specific to me. Thanks so much. If there are any potential details I forgot to specify, just ask. ** ADDITIONAL INFORMATION ** Going to development.thegraduate.hk/public/ will correctly display the index.html page in /rails_apps/thegraduate/public. However, changing root in the routes.rb file to "root = 'home#index'" does nothing.

  Read the article

• apache tomcat loadbalancing clustering on ubuntu

  - by user740010

  i am facing a problem in clustering the tomcat with apache as a loadbalancer using mod_jk on ubuntu. i have install apache2 on my ubuntu 11.04 and i have downloaded tomcat7 created two copies and kept them at two different location. 1st one is at /home/net4u/vishal/test/tomcatA 2nd one is at /home/net4u/vishal/test1/tomcatB i have made following changes to server.xml file in /conf folder 1. <Server port="8205" shutdown="SHUTDOWN"> 2. <Connector port="8280" protocol="HTTP/1.1" connectionTimeout="20000" redirectPort="8443" /> 3.<Connector port="8209" protocol="AJP/1.3" redirectPort="8443" /> <Engine name="Catalina" defaultHost="localhost" jvmRoute="tomcatB"> 4. <Cluster className="org.apache.catalina.ha.tcp.SimpleTcpCluster"/> similarly i have modified other tomcat i.e tomcatA server.xml content of the server.xml is as follow: -- <!--The connectors can use a shared executor, you can define one or more named thread pools--> <!-- <Executor name="tomcatThreadPool" namePrefix="catalina-exec-" maxThreads="150" minSpareThreads="4"/> --> <!-- A "Connector" represents an endpoint by which requests are received and responses are returned. Documentation at : Java HTTP Connector: /docs/config/http.html (blocking & non-blocking) Java AJP Connector: /docs/config/ajp.html APR (HTTP/AJP) Connector: /docs/apr.html Define a non-SSL HTTP/1.1 Connector on port 8080 --> <Connector port="8280" protocol="HTTP/1.1" connectionTimeout="20000" redirectPort="8443" /> <!-- A "Connector" using the shared thread pool--> <!-- <Connector executor="tomcatThreadPool" port="8080" protocol="HTTP/1.1" connectionTimeout="20000" redirectPort="8443" /> --> <!-- Define a SSL HTTP/1.1 Connector on port 8443 This connector uses the JSSE configuration, when using APR, the connector should be using the OpenSSL style configuration described in the APR documentation --> <!-- <Connector port="8443" protocol="HTTP/1.1" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" clientAuth="false" sslProtocol="TLS" /> --> <!-- Define an AJP 1.3 Connector on port 8009 --> <Connector port="8109" protocol="AJP/1.3" redirectPort="8443" /> <!-- An Engine represents the entry point (within Catalina) that processes every request. The Engine implementation for Tomcat stand alone analyzes the HTTP headers included with the request, and passes them on to the appropriate Host (virtual host). Documentation at /docs/config/engine.html --> <!-- You should set jvmRoute to support load-balancing via AJP ie : <Engine name="Catalina" defaultHost="localhost" jvmRoute="jvm1"> --> <Engine name="Catalina" defaultHost="localhost" jvmRoute="tomcatB"> <!--For clustering, please take a look at documentation at: /docs/cluster-howto.html (simple how to) /docs/config/cluster.html (reference documentation) --> <!-- uncomment for clustering--> <Cluster className="org.apache.catalina.ha.tcp.SimpleTcpCluster"/> <!-- Use the LockOutRealm to prevent attempts to guess user passwords via a brute-force attack --> <Realm className="org.apache.catalina.realm.LockOutRealm"> <!-- This Realm uses the UserDatabase configured in the global JNDI resources under the key "UserDatabase". Any edits that are performed against this UserDatabase are immediately available for use by the Realm. --> <Realm className="org.apache.catalina.realm.UserDatabaseRealm" resourceName="UserDatabase"/> </Realm> <Host name="localhost" appBase="webapps" unpackWARs="true" autoDeploy="true"> <!-- SingleSignOn valve, share authentication between web applications Documentation at: /docs/config/valve.html --> <!-- <Valve className="org.apache.catalina.authenticator.SingleSignOn" /> --> <!-- Access log processes all example. Documentation at: /docs/config/valve.html Note: The pattern used is equivalent to using pattern="common" --> <Valve className="org.apache.catalina.valves.AccessLogValve" directory="logs" prefix="localhost_access_log." suffix=".txt" pattern="%h %l %u %t &quot;%r&quot; %s %b" resolveHosts="false"/> </Host> </Engine> i have install libapache2-mod-jk step 1. i have Created jk.load file in /etc/apache2/mods-enabled/jk.load content is as follows: LoadModule jk_module /usr/lib/apache2/modules/mod_jk.so Create /etc/apache2/mods-enabled/jk.conf: JkWorkersFile /etc/apache2/workers.properties JkLogFile /var/log/apache2/jk.log JkMount /ecommerce/* worker1 JkMount /images/* worker1 JkMount /content/* worker1 step 2. Created workers.properties file in /etc/apache2/workers.properties content is as follows: workers.tomcat_home=/home/vishal/Desktop/test/tomcatA workers.java_home=/usr/lib/jvm/default-java ps=/ worker.list=tomcatA,tomcatB,loadbalancer   worker.tomcatA.port=8109 worker.tomcatA.host=localhost worker.tomcatA.type=ajp13 worker.tomcatA.lbfactor=1   worker.tomcatB.port=8209 worker.tomcatB.host=localhost worker.tomcatB.type=ajp13 worker.tomcatB.lbfactor=1 worker.loadbalancer.type=lb worker.loadbalancer.balanced_workers=tomcatA,tomcatB worker.loadbalancer.sticky_session=1 i tried the same thing on the windows machine it is working.

  Read the article

• Tomcat 7 on Ubuntu 12.04 with JRE 7 not starting

  - by Andreas Krueger

  I am running a virtual server in the web on Ubuntu 12.04 LTS / 32 Bit. After a clean install of JRE 7 and Tomcat 7, following the instructions on http://www.sysadminslife.com, I don't get Tomcat 7 up and running. > java -version java version "1.7.0_09" Java(TM) SE Runtime Environment (build 1.7.0_09-b05) Java HotSpot(TM) Client VM (build 23.5-b02, mixed mode) > /etc/init.d/tomcat start Starting Tomcat Using CATALINA_BASE: /usr/local/tomcat Using CATALINA_HOME: /usr/local/tomcat Using CATALINA_TMPDIR: /usr/local/tomcat/temp Using JRE_HOME: /usr/lib/jvm/java-7-oracle Using CLASSPATH: /usr/local/tomcat/bin/bootstrap.jar:/usr/local/tomcat/bin/tomcat-juli.jar > telnet localhost 8080 Trying ::1... Trying 127.0.0.1... telnet: Unable to connect to remote host: Connection refused netstat sometimes shows a Java process, most of the times not. If it does, nothing works either. Does anyone have a solution or encountered similar situations? Here are the contents of catalina.out: 16.11.2012 18:36:39 org.apache.catalina.core.AprLifecycleListener init INFO: The APR based Apache Tomcat Native library which allows optimal performance in production environments was not found on the java.library.path: /usr/lib/jvm/java-6-oracle/lib/i386/client:/usr/lib/jvm/java-6-oracle/lib/i386:/usr/lib/jvm/java-6-oracle/../lib/i386:/usr/java/packages/lib/i386:/lib:/usr/lib 16.11.2012 18:36:40 org.apache.coyote.AbstractProtocol init INFO: Initializing ProtocolHandler ["http-bio-8080"] 16.11.2012 18:36:40 org.apache.coyote.AbstractProtocol init INFO: Initializing ProtocolHandler ["ajp-bio-8009"] 16.11.2012 18:36:40 org.apache.catalina.startup.Catalina load INFO: Initialization processed in 1509 ms 16.11.2012 18:36:40 org.apache.catalina.core.StandardService startInternal INFO: Starting service Catalina 16.11.2012 18:36:40 org.apache.catalina.core.StandardEngine startInternal INFO: Starting Servlet Engine: Apache Tomcat/7.0.29 16.11.2012 18:36:40 org.apache.catalina.startup.HostConfig deployDirectory INFO: Deploying web application directory /usr/local/tomcat/webapps/manager Here come the results of ps -ef, iptables --list and netstat -plut: > ps -ef UID PID PPID C STIME TTY TIME CMD root 1 0 0 Nov16 ? 00:00:00 init root 2 1 0 Nov16 ? 00:00:00 [kthreadd/206616] root 3 2 0 Nov16 ? 00:00:00 [khelper/2066167] root 4 2 0 Nov16 ? 00:00:00 [rpciod/2066167/] root 5 2 0 Nov16 ? 00:00:00 [rpciod/2066167/] root 6 2 0 Nov16 ? 00:00:00 [rpciod/2066167/] root 7 2 0 Nov16 ? 00:00:00 [rpciod/2066167/] root 8 2 0 Nov16 ? 00:00:00 [nfsiod/2066167] root 119 1 0 Nov16 ? 00:00:00 upstart-udev-bridge --daemon root 125 1 0 Nov16 ? 00:00:00 /sbin/udevd --daemon root 157 125 0 Nov16 ? 00:00:00 /sbin/udevd --daemon root 158 125 0 Nov16 ? 00:00:00 /sbin/udevd --daemon root 205 1 0 Nov16 ? 00:00:00 upstart-socket-bridge --daemon root 276 1 0 Nov16 ? 00:00:00 /usr/sbin/sshd -D root 335 1 0 Nov16 ? 00:00:00 /usr/sbin/xinetd -dontfork -pidfile /var/run/xinetd.pid -stayalive -inetd root 348 1 0 Nov16 ? 00:00:00 cron syslog 368 1 0 Nov16 ? 00:00:00 /sbin/syslogd -u syslog root 472 1 0 Nov16 ? 00:00:00 /usr/lib/postfix/master postfix 482 472 0 Nov16 ? 00:00:00 qmgr -l -t fifo -u root 520 1 0 Nov16 ? 00:00:04 /usr/sbin/apache2 -k start www-data 523 520 0 Nov16 ? 00:00:00 /usr/sbin/apache2 -k start www-data 525 520 0 Nov16 ? 00:00:00 /usr/sbin/apache2 -k start www-data 526 520 0 Nov16 ? 00:00:00 /usr/sbin/apache2 -k start tomcat 1074 1 0 Nov16 ? 00:01:08 /usr/lib/jvm/java-6-oracle/bin/java -Djava.util.logging.config.file=/usr/ postfix 1351 472 0 Nov16 ? 00:00:00 tlsmgr -l -t unix -u -c postfix 3413 472 0 17:00 ? 00:00:00 pickup -l -t fifo -u -c root 3457 276 0 17:31 ? 00:00:00 sshd: root@pts/0 root 3459 3457 0 17:31 pts/0 00:00:00 -bash root 3470 3459 0 17:31 pts/0 00:00:00 ps -ef > iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- anywhere anywhere tcp dpt:http-alt ACCEPT tcp -- anywhere anywhere tcp dpt:8005 ACCEPT tcp -- anywhere anywhere tcp dpt:http-alt Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination > netstat -plut Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 *:smtp *:* LISTEN 472/master tcp 0 0 *:3213 *:* LISTEN 276/sshd tcp6 0 0 [::]:smtp [::]:* LISTEN 472/master tcp6 0 0 [::]:8009 [::]:* LISTEN 1074/java tcp6 0 0 [::]:3213 [::]:* LISTEN 276/sshd tcp6 0 0 [::]:http-alt [::]:* LISTEN 1074/java tcp6 0 0 [::]:http [::]:* LISTEN 520/apache2

  Read the article

• Cluster failover and strange gratuitous arp behavior

  - by lazerpld

  I am experiencing a strange Windows 2008R2 cluster related issue that is bothering me. I feel that I have come close as to what the issue is, but still don't fully understand what is happening. I have a two node exchange 2007 cluster running on two 2008R2 servers. The exchange cluster application works fine when running on the "primary" cluster node. The problem occurs when failing over the cluster ressource to the secondary node. When failing over the cluster to the "secondary" node, which for instance is on the same subnet as the "primary", the failover initially works ok and the cluster ressource continues to work for a couple of minutes on the new node. Which means that the recieving node does send out a gratuitous arp reply packet that updated the arp tables on the network. But after x amount of time (typically within 5 minutes time) something updates the arp-tables again because all of a sudden the cluster service does not answer to pings. So basically I start a ping to the exchange cluster address when its running on the "primary node". It works just great. I failover the cluster ressource group to the "secondary node" and I only have loss of one ping which is acceptable. The cluster ressource still answers for some time after being failed over and all of a sudden the ping starts timing out. This is telling me that the arp table initially is updated by the secondary node, but then something (which I haven't found out yet) wrongfully updates it again, probably with the primary node's MAC. Why does this happen - has anyone experienced the same problem? The cluster is NOT running NLB and the problem stops immidiately after failing over back to the primary node where there are no problems. Each node is using NIC teaming (intel) with ALB. Each node is on the same subnet and has gateway and so on entered correctly as far as I am concerned. Edit: I was wondering if it could be related to network binding order maybe? Because I have noticed that the only difference I can see from node to node is when showing the local arp table. On the "primary" node the arp table is generated on the cluster address as the source. While on the "secondary" its generated from the nodes own network card. Any input on this? Edit: Ok here is the connection layout. Cluster address: A.B.6.208/25 Exchange application address: A.B.6.212/25 Node A: 3 physical nics. Two teamed using intels teaming with the address A.B.6.210/25 called public The last one used for cluster traffic called private with 10.0.0.138/24 Node B: 3 physical nics. Two teamed using intels teaming with the address A.B.6.211/25 called public The last one used for cluster traffic called private with 10.0.0.139/24 Each node sits in a seperate datacenter connected together. End switches being cisco in DC1 and NEXUS 5000/2000 in DC2. Edit: I have been testing a little more. I have now created an empty application on the same cluster, and given it another ip address on the same subnet as the exchange application. After failing this empty application over, I see the exact same problem occuring. After one or two minutes clients on other subnets cannot ping the virtual ip of the application. But while clients on other subnets cannot, another server from another cluster on the same subnet has no trouble pinging. But if i then make another failover to the original state, then the situation is the opposite. So now clients on same subnet cannot, and on other they can. We have another cluster set up the same way and on the same subnet, with the same intel network cards, the same drivers and same teaming settings. Here we are not seeing this. So its somewhat confusing. Edit: OK done some more research. Removed the NIC teaming of the secondary node, since it didnt work anyway. After some standard problems following that, I finally managed to get it up and running again with the old NIC teaming settings on one single physical network card. Now I am not able to reproduce the problem described above. So it is somehow related to the teaming - maybe some kind of bug? Edit: Did some more failing over without being able to make it fail. So removing the NIC team looks like it was a workaround. Now I tried to reestablish the intel NIC teaming with ALB (as it was before) and i still cannot make it fail. This is annoying due to the fact that now i actually cannot pinpoint the root of the problem. Now it just seems to be some kind of MS/intel hick-up - which is hard to accept because what if the problem reoccurs in 14 days? There is a strange thing that happened though. After recreating the NIC team I was not able to rename the team to "PUBLIC" which the old team was called. So something has not been cleaned up in windows - although the server HAS been restarted! Edit: OK after restablishing the ALB teaming the error came back. So I am now going to do some thorough testing and i will get back with my observations. One thing is for sure. It is related to Intel 82575EB NICS, ALB and Gratuitous Arp.

  Read the article

• help setting up an IPSEC vpn from my linux box

  - by robthewolf

  I have an office with a router and a remote server (Linux - Ubuntu 10.10). Both locations need to connect to a data supplier through a VPN. The VPN is an IPSEC gateway. I was able to configure my Linksys rv42 router to create a VPN connection successfully and now I need to do the same for Linux server. I have been messing around with this for too long. First I tried OpenVPN, but that is SSL and not IPSEC. Then I tried Shrew. I think I have the settings correct but I haven't been able to create the connection. It maybe that I have to use something else like a direct IPSEC config or something like that. If someone knows of a way to turn the following settings that I have been given below into a working IPSEC VPN connection I would be very grateful. Here are the settings I was given that must be used to connect to my supplier: Local destination network: 192.168.4.0/24 Local destination hosts: 192.168.4.100 Remote destination network: 192.167.40.0/24 Remote destination hosts: 192.168.40.27 VPN peering point: xxx.xxx.xxx.xxx Then they have given me the following details: IPSEC/ISAKMP Phase 1 Parameters: Authentication method: pre shared secret Diffie Hellman group: group 2 Encryption Algorithm: 3DES Lifetime in seconds:28800 Phase 2 parameters: IPSEC security: ESP Encryption algortims: 3DES Authentication algorithms: MD5 lifetime in seconds: 28800 pfs: disabled Here are the settings from my attempt to use shrew: n:version:2 n:network-ike-port:500 n:network-mtu-size:1380 n:client-addr-auto:0 n:network-frag-size:540 n:network-dpd-enable:1 n:network-notify-enable:1 n:client-banner-enable:1 n:client-dns-used:1 b:auth-mutual-psk:YjJzN2QzdDhyN2EyZDNpNG42ZzQ= n:phase1-dhgroup:2 n:phase1-keylen:0 n:phase1-life-secs:28800 n:phase1-life-kbytes:0 n:vendor-chkpt-enable:0 n:phase2-keylen:0 n:phase2-pfsgroup:-1 n:phase2-life-secs:28800 n:phase2-life-kbytes:0 n:policy-nailed:0 n:policy-list-auto:1 n:client-dns-auto:1 n:network-natt-port:4500 n:network-natt-rate:15 s:client-dns-addr:0.0.0.0 s:client-dns-suffix: s:network-host:xxx.xxx.xxx.xxx s:client-auto-mode:pull s:client-iface:virtual s:client-ip-addr:192.168.4.0 s:client-ip-mask:255.255.255.0 s:network-natt-mode:enable s:network-frag-mode:disable s:auth-method:mutual-psk s:ident-client-type:address s:ident-client-data:192.168.4.0 s:ident-server-type:address s:ident-server-data:192.168.40.0 s:phase1-exchange:aggressive s:phase1-cipher:3des s:phase1-hash:md5 s:phase2-transform:3des s:phase2-hmac:md5 s:ipcomp-transform:disabled Finally here is the debug output from the shrew log: 10/12/22 17:22:18 ii : ipc client process thread begin ... 10/12/22 17:22:18 < A : peer config add message 10/12/22 17:22:18 DB : peer added ( obj count = 1 ) 10/12/22 17:22:18 ii : local address 217.xxx.xxx.xxx selected for peer 10/12/22 17:22:18 DB : tunnel added ( obj count = 1 ) 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : client config message 10/12/22 17:22:18 < A : local id '192.168.4.0' message 10/12/22 17:22:18 < A : remote id '192.168.40.0' message 10/12/22 17:22:18 < A : preshared key message 10/12/22 17:22:18 < A : peer tunnel enable message 10/12/22 17:22:18 DB : new phase1 ( ISAKMP initiator ) 10/12/22 17:22:18 DB : exchange type is aggressive 10/12/22 17:22:18 DB : 217.xxx.xxx.xxx:500 <- 206.xxx.xxx.xxx:500 10/12/22 17:22:18 DB : c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 DB : phase1 added ( obj count = 1 ) 10/12/22 17:22:18 : security association payload 10/12/22 17:22:18 : - proposal #1 payload 10/12/22 17:22:18 : -- transform #1 payload 10/12/22 17:22:18 : key exchange payload 10/12/22 17:22:18 : nonce payload 10/12/22 17:22:18 : identification payload 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v00 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v01 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v02 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v03 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( rfc ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports DPDv1 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SHREW SOFT compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is NETSCREEN compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SIDEWINDER compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is CISCO UNITY compatible 10/12/22 17:22:18 = : cookies c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 = : message 00000000 10/12/22 17:22:18 - : send IKE packet 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 ( 484 bytes ) 10/12/22 17:22:18 DB : phase1 resend event scheduled ( ref count = 2 ) 10/12/22 17:22:18 ii : opened tap device tap0 10/12/22 17:22:28 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:38 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:48 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:58 ii : resend limit exceeded for phase1 exchange 10/12/22 17:22:58 ii : phase1 removal before expire time 10/12/22 17:22:58 DB : phase1 deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : closed tap device tap0 10/12/22 17:22:58 DB : tunnel stats event canceled ( ref count = 1 ) 10/12/22 17:22:58 DB : removing tunnel config references 10/12/22 17:22:58 DB : removing tunnel phase2 references 10/12/22 17:22:58 DB : removing tunnel phase1 references 10/12/22 17:22:58 DB : tunnel deleted ( obj count = 0 ) 10/12/22 17:22:58 DB : removing all peer tunnel refrences 10/12/22 17:22:58 DB : peer deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : ipc client process thread exit ...

  Read the article

• How to invalidate nginx reverse proxy cache in front of other nginx servers?

  - by Olivier Lance

  I'm running a Proxmox server on a single IP address, that will dispatch HTTP requests to containers depending on the requested host. I am using nginx on the Proxmox side to listen to HTTP requests and I am using the proxy_pass directive in my different server blocks to dispatch requests according to the server_name. My containers run on Ubuntu and are also running a nginx instance. I'm having troubles with caching on a particular website that is fully static: nginx keeps on serving me stale content after files updates, until I: Clear /var/cache/nginx/ and restart nginx or set proxy_cache off for this server and reload the config Here's the detail of my configuration: On the server (proxmox): /etc/nginx/nginx.conf: user www-data; worker_processes 8; pid /var/run/nginx.pid; events { worker_connections 768; # multi_accept on; use epoll; } http { ## # Basic Settings ## sendfile on; #tcp_nopush on; tcp_nodelay on; #keepalive_timeout 65; types_hash_max_size 2048; server_tokens off; # server_names_hash_bucket_size 64; # server_name_in_redirect off; include /etc/nginx/mime.types; default_type application/octet-stream; client_body_buffer_size 1k; client_max_body_size 8m; large_client_header_buffers 1 1K; ignore_invalid_headers on; client_body_timeout 5; client_header_timeout 5; keepalive_timeout 5 5; send_timeout 5; server_name_in_redirect off; ## # Logging Settings ## access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; ## # Gzip Settings ## gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; gzip_vary on; gzip_proxied any; gzip_comp_level 6; # gzip_buffers 16 8k; gzip_http_version 1.1; gzip_types text/plain text/css application/json application/x-javascript text/xml application/xml application/xml+rss text/javascript; limit_conn_zone $binary_remote_addr zone=gulag:1m; limit_conn gulag 50; ## # Virtual Host Configs ## include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } /etc/nginx/conf.d/proxy.conf: proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_hide_header X-Powered-By; proxy_intercept_errors on; proxy_buffering on; proxy_cache_key "$scheme://$host$request_uri"; proxy_cache_path /var/cache/nginx levels=1:2 keys_zone=cache:10m inactive=7d max_size=700m; /etc/nginx/sites-available/my-domain.conf: server { listen 80; server_name .my-domain.com; access_log off; location / { proxy_pass http://my-domain.local:80/; proxy_cache cache; proxy_cache_valid 12h; expires 30d; proxy_cache_use_stale error timeout invalid_header updating; } } On the container (my-domain.local): nginx.conf: (everything is inside the main config file -- it's been done quickly...) user www-data; worker_processes 1; error_log logs/error.log; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; sendfile on; #tcp_nopush on; keepalive_timeout 65; gzip off; server { listen 80; server_name .my-domain.com; root /var/www; access_log logs/host.access.log; } } I've read many blog posts and answers before resolving to posting my own questions... most answers I can see suggest setting sendfile off; but that didn't work for me. I have tried many other things, double checked my settings and all seems fine. So I'm wondering whether I am not expecting nginx's cache to do something it's not meant to...? Basically, I thought that if one of my static files in my container was updated, the cache in my reverse proxy would be invalidated and my browser would get the new version of the file when it requests it... But I now have the sentiment I misunderstood many things. Of all things, I now wonder how nginx on the server can know about a file in the container has changed? I have seen a directive proxy_header_pass (or something alike), should I use this to let the nginx instance from the container somehow inform the one in Proxmox about updated files? Is this expectation just a dream, or can I do it with nginx on my current architecture?

  Read the article

• Cisco: unable to negotiate IP using IPCP with Windows server

  - by lnk

  I am connecting to Windows server using PPP (for vpn), I establish connection but server does not respond me for my address requests: *Mar 23 00:40:06.055: Vi1 MS-CHAP-V2: I CHALLENGE id 0 len 25 from "MSDC" *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using hostname from interface CHAP *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using password from interface CHAP *Mar 23 00:40:06.067: Vi1 MS-CHAP-V2: O RESPONSE id 0 len 69 from "XXX" *Mar 23 00:40:06.087: Vi1 PPP: I pkt type 0xC223, datagramsize 50 link[ppp] *Mar 23 00:40:06.087: Vi1 MS-CHAP-V2: I SUCCESS id 0 len 46 msg is "S=XXX" *Mar 23 00:40:06.087: Vi1 MS CHAP V2 No Password found for : XXX *Mar 23 00:40:06.091: Vi1 MS CHAP V2 Check AuthenticatorResponse Success for : XXX *Mar 23 00:40:06.091: Vi1 IPCP: O CONFREQ [Closed] id 1 len 20 *Mar 23 00:40:06.091: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:06.091: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:07.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up *Mar 23 00:40:07.091: Vi1 LCP: O ECHOREQ [Open] id 1 len 12 magic 0x194CAFCF *Mar 23 00:40:07.103: Vi1 LCP-FS: I ECHOREP [Open] id 1 len 12 magic 0x361B62E5 *Mar 23 00:40:07.103: Vi1 LCP-FS: Received id 1, sent id 1, line up *Mar 23 00:40:08.083: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:08.083: Vi1 IPCP: O CONFREQ [REQsent] id 2 len 20 *Mar 23 00:40:08.083: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:08.083: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:10.099: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:10.099: Vi1 IPCP: O CONFREQ [REQsent] id 3 len 20 *Mar 23 00:40:10.099: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:10.099: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.115: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:12.115: Vi1 IPCP: O CONFREQ [REQsent] id 4 len 20 *Mar 23 00:40:12.115: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:12.115: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.211: Vi1 LCP: O ECHOREQ [Open] id 2 len 12 magic 0x194CAFCF *Mar 23 00:40:12.219: Vi1 LCP-FS: I ECHOREP [Open] id 2 len 12 magic 0x361B62E5 *Mar 23 00:40:12.219: Vi1 LCP-FS: Received id 2, sent id 2, line up *Mar 23 00:40:14.131: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:14.131: Vi1 IPCP: O CONFREQ [REQsent] id 5 len 20 *Mar 23 00:40:14.131: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:14.131: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:16.147: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:16.147: Vi1 IPCP: O CONFREQ [REQsent] id 6 len 20 *Mar 23 00:40:16.147: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:16.147: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:17.331: Vi1 LCP: O ECHOREQ [Open] id 3 len 12 magic 0x194CAFCF *Mar 23 00:40:17.343: Vi1 LCP-FS: I ECHOREP [Open] id 3 len 12 magic 0x361B62E5 *Mar 23 00:40:17.343: Vi1 LCP-FS: Received id 3, sent id 3, line up You see: My router asks for address, but only keepalives are on line. But the same server works with windows client!! ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption service internal ! hostname Router ! boot-start-marker boot-end-marker ! ! no aaa new-model ! resource policy ! ip subnet-zero ! ! ip cef vpdn enable ! vpdn-group pptp request-dialin protocol pptp pool-member 1 initiate-to ip XXXX ! ! ! ! ! ! ! bridge irb ! ! interface ATM0 no ip address shutdown no atm ilmi-keepalive dsl operating-mode auto ! interface FastEthernet0 ! interface FastEthernet1 ! interface FastEthernet2 ! interface FastEthernet3 ! interface Dot11Radio0 no ip address shutdown speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Vlan1 no ip address bridge-group 1 ! interface Dialer0 ip address negotiated encapsulation ppp dialer pool 1 dialer idle-timeout 0 dialer string XXX dialer persistent dialer vpdn dialer-group 1 keepalive 5 3 no cdp enable ppp authentication ms-chap-v2 optional ppp eap refuse ppp chap hostname XXX ppp chap password 0 XXX ppp ipcp mask request ppp ipcp ignore-map ppp ipcp address accept ! interface BVI1 mac-address XXX.XXX.XXX ip address dhcp ! ip classless ip route 172.0.0.0 255.0.0.0 Dialer0 ! no ip http server no ip http secure-server ! dialer-list 1 protocol ip permit ! control-plane ! bridge 1 protocol vlan-bridge bridge 1 route ip ! line con 0 no modem enable line aux 0 line vty 0 4 login ! scheduler max-task-time 5000 end

  Read the article

• Issues with Apache redirect to www-prefixed URL

  - by lamp_scaler

  I have a website with domain mysite.com. I would like to have it so that if a user types in "mysite.com" it will redirect to "www.mysite.com". Additionally, "mysite.com/subdir" will also redirect to "www.mysite.com/subdir". I've looked and made changes with vhosts and also rewrites, but it's not working for the "mysite.com/subdir"-"www.mysite.com/subdir" case. Every time I type in "mysite.com/subdir", it will redirect to "www.mysite.com". Only "www.mysite.com/subdir" works. Not sure how to troubleshoot this. I turned on rewrite logs and didn't see anything obvious, yet. This is my config files so far. Please let me know what I'm missing. Thanks! FYI: I'm using CentOS 5.4, nginx 1.2.0 on top of Apache 2.2.3. The site itself is built with CodeIgniter framework. http.conf: ServerTokens Prod ServerRoot "/etc/httpd" PidFile run/httpd.pid Timeout 120 KeepAlive Off MaxKeepAliveRequests 100 KeepAliveTimeout 15 <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 10 ServerLimit 256 MaxClients 60 MaxRequestsPerChild 10000 #StartServers 8 #MinSpareServers 5 #MaxSpareServers 20 #ServerLimit 256 #MaxClients 256 #MaxRequestsPerChild 4000 </IfModule> <IfModule worker.c> StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> Listen 69 LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule auth_digest_module modules/mod_auth_digest.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authn_alias_module modules/mod_authn_alias.so LoadModule authn_anon_module modules/mod_authn_anon.so LoadModule authn_dbm_module modules/mod_authn_dbm.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule authz_owner_module modules/mod_authz_owner.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_dbm_module modules/mod_authz_dbm.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule ldap_module modules/mod_ldap.so LoadModule authnz_ldap_module modules/mod_authnz_ldap.so LoadModule log_config_module modules/mod_log_config.so LoadModule logio_module modules/mod_logio.so LoadModule env_module modules/mod_env.so LoadModule ext_filter_module modules/mod_ext_filter.so LoadModule mime_magic_module modules/mod_mime_magic.so LoadModule expires_module modules/mod_expires.so LoadModule deflate_module modules/mod_deflate.so LoadModule headers_module modules/mod_headers.so LoadModule usertrack_module modules/mod_usertrack.so LoadModule setenvif_module modules/mod_setenvif.so LoadModule mime_module modules/mod_mime.so LoadModule dav_module modules/mod_dav.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule dav_fs_module modules/mod_dav_fs.so LoadModule vhost_alias_module modules/mod_vhost_alias.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule dir_module modules/mod_dir.so LoadModule actions_module modules/mod_actions.so LoadModule speling_module modules/mod_speling.so LoadModule alias_module modules/mod_alias.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule proxy_module modules/mod_proxy.so LoadModule proxy_balancer_module modules/mod_proxy_balancer.so LoadModule proxy_ftp_module modules/mod_proxy_ftp.so LoadModule proxy_http_module modules/mod_proxy_http.so LoadModule proxy_connect_module modules/mod_proxy_connect.so LoadModule cache_module modules/mod_cache.so LoadModule suexec_module modules/mod_suexec.so LoadModule disk_cache_module modules/mod_disk_cache.so LoadModule file_cache_module modules/mod_file_cache.so LoadModule mem_cache_module modules/mod_mem_cache.so LoadModule cgi_module modules/mod_cgi.so LoadModule version_module modules/mod_version.so #rpaf settings LoadModule rpaf_module modules/mod_rpaf-2.0.so RPAFenable On RPAFproxy_ips 127.0.0.1 RPAFsethostname On # The header where the real client IP address is stored. RPAFheader X-Forwarded-For Include conf.d/*.conf User apache Group apache ServerAdmin root@localhost ServerName www.mysite.com:80 UseCanonicalName Off DocumentRoot "/var/www/html" <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory "/var/www/html"> Options Indexes FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> <IfModule mod_userdir.c> UserDir disable </IfModule> DirectoryIndex index.html index.html.var AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all </Files> <DirectoryMatch "^/.*/\.svn/"> Order deny,allow Deny from all </DirectoryMatch> TypesConfig /etc/mime.types DefaultType text/plain <IfModule mod_mime_magic.c> MIMEMagicFile conf/magic </IfModule> HostnameLookups Off ErrorLog logs/error_log LogLevel warn LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent CustomLog logs/access_log combined ServerSignature Off Alias /icons/ "/var/www/icons/" <Directory "/var/www/icons"> Options Indexes MultiViews AllowOverride None Order allow,deny Allow from all </Directory> <IfModule mod_dav_fs.c> DAVLockDB /var/lib/dav/lockdb </IfModule> ScriptAlias /cgi-bin/ "/var/www/cgi-bin/" <Directory "/var/www/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> IndexOptions FancyIndexing VersionSort NameWidth=* HTMLTable AddIconByEncoding (CMP,/icons/compressed.gif) x-compress x-gzip AddIconByType (TXT,/icons/text.gif) text/* AddIconByType (IMG,/icons/image2.gif) image/* AddIconByType (SND,/icons/sound2.gif) audio/* AddIconByType (VID,/icons/movie.gif) video/* AddIcon /icons/binary.gif .bin .exe AddIcon /icons/binhex.gif .hqx AddIcon /icons/tar.gif .tar AddIcon /icons/world2.gif .wrl .wrl.gz .vrml .vrm .iv AddIcon /icons/compressed.gif .Z .z .tgz .gz .zip AddIcon /icons/a.gif .ps .ai .eps AddIcon /icons/layout.gif .html .shtml .htm .pdf AddIcon /icons/text.gif .txt AddIcon /icons/c.gif .c AddIcon /icons/p.gif .pl .py AddIcon /icons/f.gif .for AddIcon /icons/dvi.gif .dvi AddIcon /icons/uuencoded.gif .uu AddIcon /icons/script.gif .conf .sh .shar .csh .ksh .tcl AddIcon /icons/tex.gif .tex AddIcon /icons/bomb.gif core AddIcon /icons/back.gif .. AddIcon /icons/hand.right.gif README AddIcon /icons/folder.gif ^^DIRECTORY^^ AddIcon /icons/blank.gif ^^BLANKICON^^ DefaultIcon /icons/unknown.gif #AddDescription "GZIP compressed document" .gz #AddDescription "tar archive" .tar #AddDescription "GZIP compressed tar archive" .tgz ReadmeName README.html HeaderName HEADER.html IndexIgnore .??* *~ *# HEADER* README* RCS CVS *,v *,t AddLanguage ca .ca AddLanguage cs .cz .cs AddLanguage da .dk AddLanguage de .de AddLanguage el .el AddLanguage en .en AddLanguage eo .eo AddLanguage es .es AddLanguage et .et AddLanguage fr .fr AddLanguage he .he AddLanguage hr .hr AddLanguage it .it AddLanguage ja .ja AddLanguage ko .ko AddLanguage ltz .ltz AddLanguage nl .nl AddLanguage nn .nn AddLanguage no .no AddLanguage pl .po AddLanguage pt .pt AddLanguage pt-BR .pt-br AddLanguage ru .ru AddLanguage sv .sv AddLanguage zh-CN .zh-cn AddLanguage zh-TW .zh-tw LanguagePriority en zh-CN zh-TW ca cs da de el eo es et fr he hr it ja ko ltz nl nn no pl pt pt-BR ru sv ForceLanguagePriority Prefer Fallback AddDefaultCharset UTF-8 AddType text/x-component .htc AddType application/x-compress .Z AddType application/x-gzip .gz .tgz AddHandler type-map var AddType text/html .shtml AddOutputFilter INCLUDES .shtml Alias /error/ "/var/www/error/" <IfModule mod_negotiation.c> <IfModule mod_include.c> <Directory "/var/www/error"> AllowOverride None Options IncludesNoExec AddOutputFilter Includes html AddHandler type-map var Order allow,deny Allow from all LanguagePriority en es de fr ForceLanguagePriority Prefer Fallback </Directory> </IfModule> </IfModule> BrowserMatch "Mozilla/2" nokeepalive BrowserMatch "MSIE 4\.0b2;" nokeepalive downgrade-1.0 force-response-1.0 BrowserMatch "RealPlayer 4\.0" force-response-1.0 BrowserMatch "Java/1\.0" force-response-1.0 BrowserMatch "JDK/1\.0" force-response-1.0 BrowserMatch "Microsoft Data Access Internet Publishing Provider" redirect-carefully BrowserMatch "MS FrontPage" redirect-carefully BrowserMatch "^WebDrive" redirect-carefully BrowserMatch "^WebDAVFS/1.[0123]" redirect-carefully BrowserMatch "^gnome-vfs/1.0" redirect-carefully BrowserMatch "^XML Spy" redirect-carefully BrowserMatch "^Dreamweaver-WebDAV-SCM1" redirect-carefully vhost.conf: NameVirtualHost *:69 <VirtualHost *:69> ServerName mysite.com ServerAlias vip.mysite.com Redirect / http://www.mysite.com/ </VirtualHost> <VirtualHost *:69> DocumentRoot /home/mysite/mysite/www ServerName www.mysite.com </VirtualHost> <VirtualHost *:69> DocumentRoot /home/mysite/mysite/www/assets ServerName static.mysite.com </VirtualHost> <VirtualHost *:69> DocumentRoot /home/mysite/admin/www ServerName admin.mysite.com </VirtualHost> <VirtualHost *:69> DocumentRoot /home/other/trunk/www ServerName othersite.com ServerAlias www.othersite.com </VirtualHost> <VirtualHost *:69> DocumentRoot /var/www/html ServerName test.mysite.com ServerAlias test2.mysite.com </VirtualHost> /home/mysite/mysite/www/.htaccess: RewriteEngine on # In my case all CI files are outside this web root, so we can # allow any files or directories that exist to be displayed directly RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d # hide index.php RewriteRule .* index.php/$0 [L] # BEGIN Compress text files <ifModule mod_deflate.c> <filesMatch "\.(css|js|x?html?|php)$"> SetOutputFilter DEFLATE </filesMatch> </ifModule> # END Compress text files # BEGIN Expire headers <ifModule mod_expires.c> ExpiresActive On ExpiresDefault "access plus 1 seconds" ExpiresByType image/x-icon "access plus 2592000 seconds" ExpiresByType image/jpeg "access plus 2592000 seconds" ExpiresByType image/png "access plus 2592000 seconds" ExpiresByType image/gif "access plus 2592000 seconds" ExpiresByType application/x-shockwave-flash "access plus 2592000 seconds" ExpiresByType text/css "access plus 604800 seconds" ExpiresByType text/javascript "access plus 604800 seconds" ExpiresByType application/javascript "access plus 604800 seconds" ExpiresByType application/x-javascript "access plus 604800 seconds" ExpiresByType application/xhtml+xml "access plus 600 seconds" </ifModule> # END Expire headers # BEGIN Cache-Control Headers <ifModule mod_headers.c> <filesMatch "\.(ico|jpe?g|png|gif|swf)$"> Header set Cache-Control "max-age=2592000, public" </filesMatch> <filesMatch "\.(css)$"> Header set Cache-Control "max-age=604800, public" </filesMatch> <filesMatch "\.(js)$"> Header set Cache-Control "max-age=604800, private" </filesMatch> </ifModule> # END Cache-Control Headers # BEGIN Turn ETags Off <ifModule mod_headers.c> Header unset ETag </ifModule> FileETag None # END Turn ETags Off /etc/nginx/conf.d/default.conf: server { listen 80; server_name static.mysite.com; location / { root /home/mysite/mysite/www/assets; index index.html index.htm; expires max; } } server { listen 80; server_name *.mysite.com www.mysite.com vip.mysite.com; #Set this larger if uploading big files client_max_body_size 5m; location / { proxy_pass http://127.0.0.1:69; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; #client_max_body_size 10m; client_body_buffer_size 128k; proxy_buffer_size 4k; proxy_buffers 4 32k; } }

  Read the article

• firefox, opera 'The connection was reset' on few POST method calls on Windows and Ubuntu

  - by Gopalakrishnan Subramani

  my website works well with GET method, also few POST methods. Some pages with POST method doesn't work. Some pages with POST work. For example, login page uses POST that works fine. When I post the data on webpage, firefox says "Connecting..." and finally report connection timed out error. The same behavior happens with Opera as well. However Google Chrome works fine. At the server side, I use nginx 1.2.4 with HTTPS and uwsgi for python (flask framework) app. I use geotrust certificate. The same behavior happens with Windows 7 and Ubuntu 12.04 on firefox. I tried firefox in safemode, but no luck. Set auto-detect proxy settings. no luck. Cleared all cookies. no luck Anyone help me to fix this issue? I am posting ngix config. shame on me. I use root, I know which is not advised. need to fix soon. user root; worker_processes 4; pid /var/run/nginx.pid; events { worker_connections 768; # multi_accept on; } http { ## # Basic Settings ## sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; # server_tokens off; # server_names_hash_bucket_size 64; # server_name_in_redirect off; include /etc/nginx/mime.types; default_type application/octet-stream; ## # Logging Settings ## access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; ## # Gzip Settings ## gzip on; gzip_disable "msie6"; # gzip_vary on; # gzip_proxied any; # gzip_comp_level 6; # gzip_buffers 16 8k; # gzip_http_version 1.1; # gzip_types text/plain text/css application/json application/x-javascript text/xml application/xml application/xml+rss text/javascript; ## # nginx-naxsi config ## # Uncomment it if you installed nginx-naxsi ## #include /etc/nginx/naxsi_core.rules; ## # nginx-passenger config ## # Uncomment it if you installed nginx-passenger ## #passenger_root /usr; #passenger_ruby /usr/bin/ruby; ## # Virtual Host Configs ## include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; ssl_session_cache shared:SSL:10m; ssl_session_timeout 10m; server { listen 80; server_name www.example.com; rewrite ^(.*) https://example.com$1 permanent; } server { listen 80; server_name example.com; rewrite ^ https://$server_name$request_uri? permanent; } server { listen 443; server_name example.com; keepalive_timeout 70; ssl on; ssl_certificate /root/cc.cert; ssl_certificate_key /root/cc.key; ssl_protocols SSLv3 TLSv1 TLSv1.1 TLSv1.2; #ssl_ciphers HIGH:!aNULL:!MD5; ssl_ciphers RC4:HIGH:!aNULL:!MD5; ssl_prefer_server_ciphers on; location / { try_files $uri @app; } location @app { include uwsgi_params; uwsgi_pass unix:/tmp/uwsgi.sock; } } } #mail { # # See sample authentication script at: # # http://wiki.nginx.org/ImapAuthenticateWithApachePhpScript # # # auth_http localhost/auth.php; # # pop3_capabilities "TOP" "USER"; # # imap_capabilities "IMAP4rev1" "UIDPLUS"; # # server { # listen localhost:110; # protocol pop3; # proxy on; # } # # server { # listen localhost:143; # protocol imap; # proxy on; # } #}

  Read the article

• I added some options to stop spam with Postfix, but now won't send email to remote domains

  - by willdanceforfun

  I had a working Postfix server, but added a few lines to my main.cf in a hope to block some common spam. Those lines I added were: smtpd_helo_required = yes smtpd_recipient_restrictions = reject_invalid_hostname, reject_unknown_recipient_domain, reject_unauth_pipelining, permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination, reject_rbl_client multi.uribl.com, reject_rbl_client dsn.rfc-ignorant.org, reject_rbl_client dul.dnsbl.sorbs.net, reject_rbl_client list.dsbl.org, reject_rbl_client sbl-xbl.spamhaus.org, reject_rbl_client bl.spamcop.net, reject_rbl_client dnsbl.sorbs.net, reject_rbl_client cbl.abuseat.org, reject_rbl_client ix.dnsbl.manitu.net, reject_rbl_client combined.rbl.msrbl.net, reject_rbl_client rabl.nuclearelephant.com, permit It appears my postfix is now receiving normal emails fine, and blocking spam emails. But when I now try to use this server myself to send to a remote domain (an email not on my server) I get bounced, with maillog saying something like this: Nov 12 06:19:36 srv postfix/smtpd[11756]: NOQUEUE: reject: RCPT from unknown[xx.xx.x.xxx]: 450 4.1.2 <[email protected]>: Recipient address rejected: Domain not found; from=<[email protected]> to=<[email protected]> proto=ESMTP helo=<[192.168.1.100]> Is that saying 'domain not found' for gmail.com? Why is that recipient address rejected? An output of my postconf-n is: alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases broken_sasl_auth_clients = yes command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix debug_peer_level = 2 html_directory = no inet_interfaces = all inet_protocols = all mail_owner = postfix mailbox_size_limit = 0 mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man mydestination = $myhostname, localhost.$mydomain, localhost, $mydomain mydomain = primarydomain.net myhostname = mail.primarydomain.net myorigin = $myhostname newaliases_path = /usr/bin/newaliases.postfix queue_directory = /var/spool/postfix readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES relay_domains = $mydestination, primarydomain.net, secondarydomain.org sample_directory = /usr/share/doc/postfix-2.6.6/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtpd_client_restrictions = permit_sasl_authenticated smtpd_helo_required = yes smtpd_recipient_restrictions = reject_invalid_hostname, reject_unknown_recipient_domain, reject_unauth_pipelining, permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination, reject_rbl_client multi.uribl.com, reject_rbl_client dsn.rfc-ignorant.org, reject_rbl_client dul.dnsbl.sorbs.net, reject_rbl_client list.dsbl.org, reject_rbl_client sbl-xbl.spamhaus.org, reject_rbl_client bl.spamcop.net, reject_rbl_client dnsbl.sorbs.net, reject_rbl_client cbl.abuseat.org, reject_rbl_client ix.dnsbl.manitu.net, reject_rbl_client combined.rbl.msrbl.net, reject_rbl_client rabl.nuclearelephant.com, permit smtpd_sasl_auth_enable = yes smtpd_sasl_path = private/auth smtpd_sasl_type = dovecot smtpd_sender_restrictions = reject_unknown_sender_domain soft_bounce = no unknown_local_recipient_reject_code = 550 virtual_alias_domains = mail.secondarydomain.org virtual_alias_maps = hash:/etc/postfix/virtual Any insight greatly appreciated. Edit: here is the dig mx gmail.com from the server: ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.17.rc1.el6_4.4 <<>> mx gmail.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 31766 ;; flags: qr rd ra; QUERY: 1, ANSWER: 5, AUTHORITY: 4, ADDITIONAL: 14 ;; QUESTION SECTION: ;gmail.com. IN MX ;; ANSWER SECTION: gmail.com. 1207 IN MX 5 gmail-smtp-in.l.google.com. gmail.com. 1207 IN MX 30 alt3.gmail-smtp-in.l.google.com. gmail.com. 1207 IN MX 20 alt2.gmail-smtp-in.l.google.com. gmail.com. 1207 IN MX 40 alt4.gmail-smtp-in.l.google.com. gmail.com. 1207 IN MX 10 alt1.gmail-smtp-in.l.google.com. ;; AUTHORITY SECTION: gmail.com. 109168 IN NS ns1.google.com. gmail.com. 109168 IN NS ns4.google.com. gmail.com. 109168 IN NS ns3.google.com. gmail.com. 109168 IN NS ns2.google.com. ;; ADDITIONAL SECTION: alt1.gmail-smtp-in.l.google.com. 207 IN A 173.194.70.27 alt1.gmail-smtp-in.l.google.com. 248 IN AAAA 2a00:1450:4001:c02::1b gmail-smtp-in.l.google.com. 200 IN A 173.194.67.26 gmail-smtp-in.l.google.com. 248 IN AAAA 2a00:1450:400c:c05::1b alt3.gmail-smtp-in.l.google.com. 207 IN A 74.125.143.27 alt3.gmail-smtp-in.l.google.com. 249 IN AAAA 2a00:1450:400c:c05::1b alt2.gmail-smtp-in.l.google.com. 207 IN A 173.194.69.27 alt2.gmail-smtp-in.l.google.com. 248 IN AAAA 2a00:1450:4008:c01::1b alt4.gmail-smtp-in.l.google.com. 207 IN A 173.194.79.27 alt4.gmail-smtp-in.l.google.com. 249 IN AAAA 2607:f8b0:400e:c01::1a ns2.google.com. 281970 IN A 216.239.34.10 ns3.google.com. 281970 IN A 216.239.36.10 ns4.google.com. 281970 IN A 216.239.38.10 ns1.google.com. 281970 IN A 216.239.32.10

  Read the article

• Wireshark does not see interfaces (winXP)

  - by bua

  Short story: Wireshark is working....on my winXP-32b ... usage .... Long long time later Wireshark does not work It can't find any usefull interface (just VPN) ipconfig /all Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Dell Wireless 1490 Dual Band WLAN Mini-Card Physical Address. . . . . . . . . : SOME VALID MAC Ethernet adapter eth0: Connection-specific DNS Suffix . : xxxx Description . . . . . . . . . . . : Broadcom 440x 10/100 Integrated Controller Physical Address. . . . . . . . . : SOME VALID MAC Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.12.68 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168..... ..... Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Fortinet virtual adapter Physical Address. . . . . . . . . : SOME VALID MAC Following steps didn't help: Several Wireshark re-installation Several LIBPCAP re installation SP3 for winXP Any ideas welcome.

  Read the article

• Linux/Apache performance very slow even on local network

  - by klausch

  I have an Ubuntu server machine running Apache and MYSQL. System and version info is as follows: Linux kernel 3.0.0.-12 Apache/2.2.20 MySQL Ver 14.14.Distrib 5.1.58 I am running a few websites on this server, some HTML only, some PHP/MySQL. THe [problem is that response time is very slow, both on static as well as the dynamic sites. Sometimes it takes more than 10 seconds before a response is given, this makes the sites very slow and almost unusable. The problem occurs even when requesting from the local network. I have added the involved subdomains to my /etc/hosts file, and abolve all the problem is not solved by using IP numbers instead of URL's. So there is no DNS lookup issue. I have modified the log format by showing the response times and sometimes a files takes 12 seconds to be served, see the jquery~.js file in the example screenshot. I have no explanation for this extremely long response time, but is is not even the only issue here, some other files takes a long time to be served too, but do not show a long response time in the log file. So probably different tissues are involved here. I cannot find a solution until now, any suggestions??? THanx in advance, Klaas link to screenshot picture from access logfile Some extra configuration info: apache2.conf (comment is removed) LockFile ${APACHE_LOCK_DIR}/accept.lock PidFile ${APACHE_PID_FILE} Timeout 300 KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 5 <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 0 </IfModule> <IfModule mpm_worker_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> <IfModule mpm_event_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> DefaultType text/plain HostnameLookups Off ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn Include mods-enabled/*.load Include mods-enabled/*.conf Include httpd.conf Include ports.conf LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\" %T/%D" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent Include conf.d/ Include sites-enabled/ And the virtual hostfile for one of the slow sites, in fact it is pretty straightforward... <VirtualHost *:80> ServerAdmin [email protected] ServerSignature EMail ServerName toenjoy.drsklaus.nl DocumentRoot /var/www/toenjoy.drsklaus.nl <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/toenjoy.drsklaus.nl/> Options Indexes FollowSymLinks MultiViews AllowOverride AuthConfig AuthType Basic AuthName "To Enjoy" AuthUserFile /etc/.htpasswd Require user petraaa Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> And the output of free -m: klaas@ubuntu-server:/etc/apache2$ free -m total used free shared buffers cached Mem: 1997 1401 595 0 144 1017 -/+ buffers/cache: 238 1758 Swap: 2035 0 2035 and I have no indication that swapping occurs on the moments the site is slow. I have runned top and it does not appear to be a CPU issue. I have the impression that the spawning of a apache thread could maybe be the bottleneck but it is just a suggestion. Maybe this gives some extra information! EDIT: The problem seemed to be gone for some time but occurs again! And not only with Apache, also connecting using SSH takes a tremendous time, sometimes it takes up to 15 seconds before the keyphrase is asked for. Also scp works very slowly. The behavious is really unpredoctable and makes the server very hard to use. Any ideas...?

  Read the article

• Uncompiled WCF on IIS7: The type could not be found

  - by Jimmy

  Hello, I've been trying to follow this tutorial for deploying a WCF sample to IIS . I can't get it to work. This is a hosted site, but I do have IIS Manager access to the server. However, in step 2 of the tutorial, I can't "create a new IIS application that is physically located in this application directory". I can't seem to find a menu item, context menu item, or what not to create a new application. I've been right-clicking everywhere like crazy and still can't figure out how to create a new app. I suppose that's probably the root issue, but I tried a few other things (described below) just in case that actually is not the issue. This is "deployed" at http://test.com.cws1.my-hosting-panel.com/IISHostedCalcService/Service.svc . The error says: The type 'Microsoft.ServiceModel.Samples.CalculatorService', provided as the Service attribute value in the ServiceHost directive, or provided in the configuration element system.serviceModel/serviceHostingEnvironment/serviceActivations could not be found. I also tried to create a virtual dir (IISHostedCalc) in dotnetpanel that points to IISHostedCalcService . When I navigate to http://test.com.cws1.my-hosting-panel.com/IISHostedCalc/Service.svc , then there is a different error: This collection already contains an address with scheme http. There can be at most one address per scheme in this collection. As per the tutorial, there was no compiling involved; I just dropped the files on the server as follow inside the folder IISHostedCalcService: service.svc Web.config Service.cs service.svc contains: <%@ServiceHost language=c# Debug="true" Service="Microsoft.ServiceModel.Samples.CalculatorService"%> (I tried with quotes around the c# attribute, as this looks a little strange without quotes, but it made no difference) Web.config contains: <?xml version="1.0" encoding="utf-8" ?> <configuration> <system.serviceModel> <services> <service name="Microsoft.ServiceModel.Samples.CalculatorService"> <!-- This endpoint is exposed at the base address provided by host: http://localhost/servicemodelsamples/service.svc --> <endpoint address="" binding="wsHttpBinding" contract="Microsoft.ServiceModel.Samples.ICalculator" /> <!-- The mex endpoint is explosed at http://localhost/servicemodelsamples/service.svc/mex --> <endpoint address="mex" binding="mexHttpBinding" contract="IMetadataExchange" /> </service> </services> </system.serviceModel> <system.web> <customErrors mode="Off"/> </system.web> </configuration> Service.cs contains: using System; using System.ServiceModel; namespace Microsoft.ServiceModel.Samples { [ServiceContract] public interface ICalculator { [OperationContract] double Add(double n1, double n2); [OperationContract] double Subtract(double n1, double n2); [OperationContract] double Multiply(double n1, double n2); [OperationContract] double Divide(double n1, double n2); } public class CalculatorService : ICalculator { public double Add(double n1, double n2) { return n1 + n2; } public double Subtract(double n1, double n2) { return n1 - n2; } public double Multiply(double n1, double n2) { return n1 * n2; } public double Divide(double n1, double n2) { return n1 / n2; } } }

  Read the article

• How to run Spring 3.0 PetClinic in tomcat with Hibernate backed JPA

  - by Zwei Steinen

  OK, this probably is supposed to be the easiest thing in the world, but I've been trying for the entire day, and it's still not working.. Any help is highly appreciated! What I did: Downloaded Tomcat 6.0.26 & Spring 3.0.1 Downloaded PetClinic from https://src.springframework.org/svn/spring-samples/petclinic Built & deployed petclinic.war. Ran fine with default TopLink persistence. Edited webapps/WEB-INF/spring/applicationContext-jpa.xml and changed jpaVendorAdaptor from TopLink to Hibernate. Edited webapps/WEB-INF/web.xml and changed context-param from applicationContext-jdbc.xml to applicationContext-jpa.xml Copied everything in the Spring 3.0.1 distribution to TOMCAT_HOME/lib. Launched tomcat. Saw Caused by: java.lang.IllegalStateException: ClassLoader [org.apache.catalina.loader.WebappClassLoader] does NOT provide an 'addTransformer(ClassFileTransformer)' method. Specify a custom LoadTimeWeaver or start your Java virtual machine with Spring's agent: -javaagent:spring-agent.jar Uncommented line <Loader loaderClass="org.springframework.instrument.classloading.tomcat.TomcatInstrumentableClassLoader"/> in webapps/META-INF/context.xml. Same error. Added that line to TOMCAT_HOME/context.xml Deployed without error. However, when I do something it will issue an error saying java.lang.NoClassDefFoundError: javax/transaction/SystemException at org.hibernate.ejb.EntityManagerFactoryImpl.createEntityManager(EntityManagerFactoryImpl.java:39) at org.hibernate.ejb.EntityManagerFactoryImpl.createEntityManager(EntityManagerFactoryImpl.java:34) at org.springframework.orm.jpa.JpaTransactionManager.createEntityManagerForTransaction(JpaTransactionManager.java:400) at org.springframework.orm.jpa.JpaTransactionManager.doBegin(JpaTransactionManager.java:321) at org.springframework.transaction.support.AbstractPlatformTransactionManager.getTransaction(AbstractPlatformTransactionManager.java:371) at org.springframework.transaction.interceptor.TransactionAspectSupport.createTransactionIfNecessary(TransactionAspectSupport.java:336) at org.springframework.transaction.interceptor.TransactionInterceptor.invoke(TransactionInterceptor.java:102) at org.springframework.aop.framework.ReflectiveMethodInvocation.proceed(ReflectiveMethodInvocation.java:172) at org.springframework.aop.framework.JdkDynamicAopProxy.invoke(JdkDynamicAopProxy.java:202) at $Proxy34.findOwners(Unknown Source) at org.springframework.samples.petclinic.web.FindOwnersForm.processSubmit(FindOwnersForm.java:56) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.springframework.web.bind.annotation.support.HandlerMethodInvoker.doInvokeMethod(HandlerMethodInvoker.java:710) at org.springframework.web.bind.annotation.support.HandlerMethodInvoker.invokeHandlerMethod(HandlerMethodInvoker.java:167) at org.springframework.web.servlet.mvc.annotation.AnnotationMethodHandlerAdapter.invokeHandlerMethod(AnnotationMethodHandlerAdapter.java:414) at org.springframework.web.servlet.mvc.annotation.AnnotationMethodHandlerAdapter.handle(AnnotationMethodHandlerAdapter.java:402) at org.springframework.web.servlet.DispatcherServlet.doDispatch(DispatcherServlet.java:771) at org.springframework.web.servlet.DispatcherServlet.doService(DispatcherServlet.java:716) at org.springframework.web.servlet.FrameworkServlet.processRequest(FrameworkServlet.java:647) at org.springframework.web.servlet.FrameworkServlet.doGet(FrameworkServlet.java:552) at javax.servlet.http.HttpServlet.service(HttpServlet.java:617) at javax.servlet.http.HttpServlet.service(HttpServlet.java:717) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:290) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.springframework.web.filter.HiddenHttpMethodFilter.doFilterInternal(HiddenHttpMethodFilter.java:71) at org.springframework.web.filter.OncePerRequestFilter.doFilter(OncePerRequestFilter.java:76) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:233) at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:191) at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:127) at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:102) at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:109) at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:298) at org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:852) at org.apache.coyote.http11.Http11Protocol$Http11ConnectionHandler.process(Http11Protocol.java:588) at org.apache.tomcat.util.net.JIoEndpoint$Worker.run(JIoEndpoint.java:489) at java.lang.Thread.run(Thread.java:619) Caused by: java.lang.ClassNotFoundException: javax.transaction.SystemException at org.apache.catalina.loader.WebappClassLoader.loadClass(WebappClassLoader.java:1516) at org.apache.catalina.loader.WebappClassLoader.loadClass(WebappClassLoader.java:1361) at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:320) ... 41 more I feel silly.. What am I missing?

  Read the article

• .NET SerialPort DataReceived event not firing

  - by Klay

  I have a WPF test app for evaluating event-based serial port communication (vs. polling the serial port). The problem is that the DataReceived event doesn't seem to be firing at all. I have a very basic WPF form with a TextBox for user input, a TextBlock for output, and a button to write the input to the serial port. Here's the code: public partial class Window1 : Window { SerialPort port; public Window1() { InitializeComponent(); port = new SerialPort("COM2", 9600, Parity.None, 8, StopBits.One); port.DataReceived += new SerialDataReceivedEventHandler(port_DataReceived); port.Open(); } void port_DataReceived(object sender, SerialDataReceivedEventArgs e) { Debug.Print("receiving!"); string data = port.ReadExisting(); Debug.Print(data); outputText.Text = data; } private void Button_Click(object sender, RoutedEventArgs e) { Debug.Print("sending: " + inputText.Text); port.WriteLine(inputText.Text); } } Now, here are the complicating factors: The laptop I'm working on has no serial ports, so I'm using a piece of software called Virtual Serial Port Emulator to setup a COM2. VSPE has worked admirably in the past, and it's not clear why it would only malfunction with .NET's SerialPort class, but I mention it just in case. When I hit the button on my form to send the data, my Hyperterminal window (connected on COM2) shows that the data is getting through. Yes, I disconnect Hyperterminal when I want to test my form's ability to read the port. I've tried opening the port before wiring up the event. No change. I've read through another post here where someone else is having a similar problem. None of that info has helped me in this case. EDIT: Here's the console version (modified from http://mark.michaelis.net/Blog/TheBasicsOfSystemIOPortsSerialPort.aspx): class Program { static SerialPort port; static void Main(string[] args) { port = new SerialPort("COM2", 9600, Parity.None, 8, StopBits.One); port.DataReceived += new SerialDataReceivedEventHandler(port_DataReceived); port.Open(); string text; do { text = Console.ReadLine(); port.Write(text + "\r\n"); } while (text.ToLower() != "q"); } public static void port_DataReceived(object sender, SerialDataReceivedEventArgs args) { string text = port.ReadExisting(); Console.WriteLine("received: " + text); } } This should eliminate any concern that it's a Threading issue (I think). This doesn't work either. Again, Hyperterminal reports the data sent through the port, but the console app doesn't seem to fire the DataReceived event. EDIT #2: I realized that I had two separate apps that should both send and receive from the serial port, so I decided to try running them simultaneously... If I type into the console app, the WPF app DataReceived event fires, with the expected threading error (which I know how to deal with). If I type into the WPF app, the console app DataReceived event fires, and it echoes the data. I'm guessing the issue is somewhere in my use of the VSPE software, which is set up to treat one serial port as both input and output. And through some weirdness of the SerialPort class, one instance of a serial port can't be both the sender and receiver. Anyway, I think it's solved.

  Read the article

• Trouble determining proper decoding of a REST response from an ArcGIS REST service using IHttpModule

  - by Ryan Taylor

  First a little background on what I am trying to achieve. I have an application that is utilizing REST services served by ArcGIS Server and IIS7. The REST services return data in one of several different formats. I am requesting a JSON response. I want to be able to modify the response (remove or add parameters) before the response is sent to the client. However, I am having difficulty converting the stream to a string that I can modify. To that end, I have implemented the following code in order to try to inspect the stream. SecureModule.cs using System; using System.Web; namespace SecureModuleTest { public class SecureModule : IHttpModule { public void Init(HttpApplication context) { context.BeginRequest += new EventHandler(OnBeginRequest); } public void Dispose() { } public void OnBeginRequest(object sender, EventArgs e) { HttpApplication application = (HttpApplication) sender; HttpContext context = application.Context; HttpRequest request = context.Request; HttpResponse response = context.Response; response.Filter = new ServicesFilter(response.Filter); } } } ServicesFilter.cs using System; using System.IO; using System.Text; namespace SecureModuleTest { class ServicesFilter : MemoryStream { private readonly Stream _outputStream; private StringBuilder _content; public ServicesFilter(Stream output) { _outputStream = output; _content = new StringBuilder(); } public override void Write(byte[] buffer, int offset, int count) { _content.Append(Encoding.UTF8.GetString(buffer, offset, count)); using (TextWriter textWriter = new StreamWriter(@"C:\temp\content.txt", true)) { textWriter.WriteLine(String.Format("Buffer: {0}", _content.ToString())); textWriter.WriteLine(String.Format("Length: {0}", buffer.Length)); textWriter.WriteLine(String.Format("Offset: {0}", offset)); textWriter.WriteLine(String.Format("Count: {0}", count)); textWriter.WriteLine(""); textWriter.Close(); } // Modify response _outputStream.Write(buffer, offset, count); } } } The module is installed in the /ArcGIS/rest/ virtual directory and is executed via the following GET request. http://localhost/ArcGIS/rest/services/?f=json&pretty=true The web page displays the expected response, however, the text file tells a very different (encoded?) story. Expect Response {"currentVersion" : "10.0", "folders" : [], "services" : [ ] } Text File Contents Buffer: ? ?`I?%&/m?{J?J??t??`$?@??????iG#)?*??eVe]f@????{???{???;?N'????\fdl??J??!????~|?"~?G?u]???'?)??G?????G??7N????W??{?????,??|?OR????q? Length: 4096 Offset: 0 Count: 168 Buffer: ? ?`I?%&/m?{J?J??t??`$?@??????iG#)?*??eVe]f@????{???{???;?N'????\fdl??J??!????~|?"~?G?u]???'?)??G?????G??7N????W??{?????,??|?OR????q?K???!P Length: 4096 Offset: 0 Count: 11 Interestingly, Fiddler depicts a similar picture. Fiddler Request GET http://localhost/ArcGIS/rest/services/?f=json&pretty=true HTTP/1.1 Host: localhost Connection: keep-alive User-Agent: Mozilla/5.0 (Windows; U; Windows NT 6.1; en-US) AppleWebKit/533.4 (KHTML, like Gecko) Chrome/5.0.375.70 Safari/533.4 Referer: http://localhost/ArcGIS/rest/services Cache-Control: no-cache Pragma: no-cache Accept: application/xml,application/xhtml+xml,text/html;q=0.9,text/plain;q=0.8,image/png,*/*;q=0.5 Accept-Encoding: gzip,deflate,sdch Accept-Language: en-US,en;q=0.8 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 Cookie: a=mWz_JFOusuGPnS3w5xx1BSUuyKGB3YZo92Dy2SUntP2MFWa8MaVq6a4I_IYBLKuefXDZANQMeqvxdGBgQoqTKz__V5EQLHwxmKlUNsaK7do. Fiddler Response - Before Clicking Decode HTTP/1.1 200 OK Content-Type: text/plain;charset=utf-8 Content-Encoding: gzip ETag: 719143506 Server: Microsoft-IIS/7.5 X-Powered-By: ASP.NET Date: Thu, 10 Jun 2010 01:08:43 GMT Content-Length: 179 ????????`I?%&/m?{J?J??t??`$?@??????iG#)?*??eVe]f@????{???{???;?N'????\fdl??J??!????~|?"~?G?u]???'?)??G?????G??7N????W??{?????,??|?OR????q?K???! P??? Fiddler Response - After Clicking Decode HTTP/1.1 200 OK Content-Type: text/plain;charset=utf-8 ETag: 719143506 Server: Microsoft-IIS/7.5 X-Powered-By: ASP.NET Date: Thu, 10 Jun 2010 01:08:43 GMT Content-Length: 80 {"currentVersion" : "10.0", "folders" : [], "services" : [ ] } I think that the problem may be a result of compression and/or chunking of data (this might be why I am receiving two calls to ServicesFilter.Write(...), however, I have not yet been able to solve the issue. How might I decode, unzip, and otherwise convert the byte stream into the string I know it should be for modification by my filter?

  Read the article

• Apache2 VirtualHost Configuration with SSL

  - by Peter

  Hello! I'm new here and I have a strange problem which needs to be solved. Previously I searched in the whole forum and I've read all of related questions but I didn't find solution to my question. We have two servers and a firewall computer. On the Server#1 there is an Apache 2.2 web server and it forwards the incoming traffic to the appropriate ports, to our subdomains by its virtual host configuration (Apache, Tomcat, IIS, Server#2 and so on). We recently bought an SSL certificate to protect one of our subdomain. I successfully installed and configured the certificate into the Apache and it works flawlessly within our local network. Our Kerio Winroute Firewall is configured to permit https traffic and it is translated to Server#1. But all of our subdomains are unavailable from outside (http & https too). Web browser shows "Failed to connect" message. Now, I enclose some parts from our httpd.conf and httpd-vhosts.conf file. httpd.conf ServerRoot "C:/Program Files/Apache Software Foundation/Apache2.2" Listen 80 ServerName dev.mydomain.hu:80 DocumentRoot "C:/Program Files/Apache Software Foundation/Apache2.2/htdocs" LoadModule proxy_module modules/mod_proxy.so LoadModule proxy_connect_module modules/mod_proxy_connect.so LoadModule proxy_http_module modules/mod_proxy_http.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule ssl_module modules/mod_ssl.so Include conf/extra/httpd-vhosts.conf <IfModule ssl_module> SSLMutex default SSLRandomSeed startup builtin SSLRandomSeed connect builtin SSLSessionCache none </IfModule> httpd-vhosts.conf NameVirtualHost *:80 NameVirtualHost *:443 Listen 443 <VirtualHost *:80> DocumentRoot "C:/Program Files/Apache Software Foundation/Apache2.2/htdocs" ServerName localhost </VirtualHost> #-------EXCHANGE SERVER-------- <VirtualHost *:80> ServerName intra.mydomain.hu ProxyRequests Off ProxyVia On ProxyPass / http://myserver:8080/ ProxyPassReverse / http://myserver:8080/ <Proxy *:80> Order deny,allow Allow from all </Proxy> <Location /> Order allow,deny Allow from all </Location> ErrorLog "c:/Program Files/Apache Software Foundation/Apache2.2/logs/exchange.log" CustomLog "c:/Program Files/Apache Software Foundation/Apache2.2/logs/exchange_cust.log" common LogLevel info </VirtualHost> #--------FITNESSE SERVER------- <VirtualHost *:80> ServerName test.mydomain.hu ProxyRequests Off <Proxy *:80> Order deny,allow Allow from all </Proxy> ProxyPass / http://myserver:8004/ ProxyPassReverse / http://myserver:8004/ <Location /> AuthType Basic AuthName "FitNesse" AuthUserFile "C:/Program Files/Apache Software Foundation/Apache2.2/auth/password" AuthGroupFile "C:/Program Files/Apache Software Foundation/Apache2.2/auth/pwgroup" require group Users Order allow,deny Allow from all </Location> ErrorLog "c:/Program Files/Apache Software Foundation/Apache2.2/logs/fitnesse.log" CustomLog "c:/Program Files/Apache Software Foundation/Apache2.2/logs/fitnesse_cust.log" common LogLevel info </VirtualHost> #----WIKI SERVER-----(SSL)- <VirtualHost *:80 *:443> ServerName wiki.mydomain.hu ServerAlias wiki.mydomain.hu SSLEngine On SSLCertificateFile "C:/Program Files/Apache Software Foundation/Apache2.2/cert/certificate.cer" SSLCertificateKeyFile "C:/Program Files/Apache Software Foundation/Apache2.2/cert/wiki.itkodex.hu.key" ProxyRequests Off <Proxy *:80> Order deny,allow Allow from all </Proxy> ProxyPass / http://localhost:8000/ ProxyPassReverse / http://localhost:8000/ ErrorLog "c:/Program Files/Apache Software Foundation/Apache2.2/logs/wiki.log" CustomLog "c:/Program Files/Apache Software Foundation/Apache2.2/logs/wikicust.log" common LogLevel info </VirtualHost> Because this wiki is a JSPWIKI web application, runs on Apache Tomcat therefore there is no "DocumentRoot" parameter in the VirtualHost. Could anybody please help me, to solve this issue, or what should I modify in the configuration? Thanks in advance! Peter

  Read the article

• C++ invalid reference problem

  - by Karol

  Hi all, I'm writing some callback implementation in C++. I have an abstract callback class, let's say: /** Abstract callback class. */ class callback { public: /** Executes the callback. */ void call() { do_call(); }; protected: /** Callback call implementation specific to derived callback. */ virtual void do_call() = 0; }; Each callback I create (accepting single-argument functions, double-argument functions...) is created as a mixin using one of the following: /** Makes the callback a single-argument callback. */ template <typename T> class singleArgumentCallback { protected: /** Callback argument. */ T arg; public: /** Constructor. */ singleArgumentCallback(T arg): arg(arg) { } }; /** Makes the callback a double-argument callback. */ template <typename T, typename V> class doubleArgumentCallback { protected: /** Callback argument 1. */ T arg1; /** Callback argument 2. */ V arg2; public: /** Constructor. */ doubleArgumentCallback(T arg1, V arg2): arg1(arg1), arg2(arg2) { } }; For example, a single-arg function callback would look like this: /** Single-arg callbacks. */ template <typename T> class singleArgFunctionCallback: public callback, protected singleArgumentCallback<T> { /** Callback. */ void (*callbackMethod)(T arg); public: /** Constructor. */ singleArgFunctionCallback(void (*callback)(T), T argument): singleArgumentCallback<T>(argument), callbackMethod(callback) { } protected: void do_call() { this->callbackMethod(this->arg); } }; For user convenience, I'd like to have a method that creates a callback without having the user think about details, so that one can call (this interface is not subject to change, unfortunately): void test3(float x) { std::cout << x << std::endl; } void test5(const std::string& s) { std::cout << s << std::endl; } make_callback(&test3, 12.0f)->call(); make_callback(&test5, "oh hai!")->call(); My current implementation of make_callback(...) is as follows: /** Creates a callback object. */ template <typename T, typename U> callback* make_callback( void (*callbackMethod)(T), U argument) { return new singleArgFunctionCallback<T>(callbackMethod, argument); } Unfortunately, when I call make_callback(&test5, "oh hai!")->call(); I get an empty string on the standard output. I believe the problem is that the reference gets out of scope after callback initialization. I tried using pointers and references, but it's impossible to have a pointer/reference to reference, so I failed. The only solution I had was to forbid substituting reference type as T (for example, T cannot be std::string&) but that's a sad solution since I have to create another singleArgCallbackAcceptingReference class accepting a function pointer with following signature: void (*callbackMethod)(T& arg); thus, my code gets duplicated 2^n times, where n is the number of arguments of a callback function. Does anybody know any workaround or has any idea how to fix it? Thanks in advance!

  Read the article

• Hosting Mercurial on IIS7

  - by Lasse V. Karlsen

  Note, this might perhaps be best suited on serverfault.com, but since it is about hosting a programmer source code repository, I am not entirely sure. I'm posting here first, trusting that it'll be migrated if necessary. I'm attempting to host clones of my Mercurial repositories on my own server (I have the main repo somewhere else), and I'm attempting to set up Mercurial under IIS. I followed the guide here, but I get an error message. Solved: See bottom of this question for details. The error message is: mercurial.error.RepoError: repository /path/to/repo/or/config not found Here's what I did. I installed Mercurial 1.5.2 I created c:\inetpub\hg I downloaded the hg source as per the instructions of the webpage, and copied the hgweb.cgi file into c:\inetpub\hg (note, the webpage says hgwebdir.cgi, but this particular file does not exist, hgweb.cgi does, however, can this be the source of the problem?) I added a hgweb.config, with the following contents: [paths] repo1 = C:/hg/** [web] style = monoblue I created c:\hg, created a sub-directory test, and created a repository inside it I installed python 2.6.5, latest 2.6 version from the website (the webpage mentions I need to install the correct version or I'll get a specific error message, since I don't get an error message that looks remotely like the one mentioned, I assume that 2.6.5 is not the problem) I added a new virtual host hg.vkarlsen.no, pointing it to c:\inetpub\hg For this host, I added a script mapping under the Handler Mappings section, mapping *.cgi to c:\python26\python.exe -u %s %s as per the instructions on the website. I then tested it by navigating to http://hg.vkarlsen.no/hgweb.cgi, but I get an error message. To make it easier to test, I dropped to a command prompt, navigated to c:\inetpub\hg, and executed the following command (error message is part of the text below): C:\inetpub\hg>c:\python26\python.exe -u hgweb.cgi Traceback (most recent call last): File "hgweb.cgi", line 16, in <module> application = hgweb(config) File "mercurial\hgweb\__init__.pyc", line 12, in hgweb File "mercurial\hgweb\hgweb_mod.pyc", line 30, in __init__ File "mercurial\hg.pyc", line 82, in repository File "mercurial\localrepo.pyc", line 2221, in instance File "mercurial\localrepo.pyc", line 62, in __init__ mercurial.error.RepoError: repository /path/to/repo/or/config not found Does anyone know what I need to look at in order to fix this? Edit: Ok, I think I managed to get one step closer to the solution, but I'm still stumped. I realized the .cgi file is a python script file, and not something compile, so I opened it for editing, and these lines was sitting in it: # Path to repo or hgweb config to serve (see 'hg help hgweb') config = "/path/to/repo/or/config" So this was my source for the specific error message. If I change the line to this: config = "c:\\hg\\test" Then I can navigate the empty repository through the Mercurial web interface. However, I want to host multiple repositories, and seeing as the line says that I can also link to a hgweb config file, I tried this: config = "c:\\inetpub\\hg\\hgweb.config" But then I get the following error message: mercurial.error.Abort: c:\inetpub\hg\hgweb.config: not a Mercurial bundle file Exception ImportError: 'No module named shutil' in <bound method bundlerepository.__del__ of <mercurial.bundlerepo.bundlerepository object at 0x0260A110>> ignored Nothing I've tried for the config variable seems to work: config = "hgweb.config" config = "c:\\hg\\hgweb.config" various other variations I don't remember. So, still stumped, pointers anyone? Solved: I ended up having to edit the hgweb.cgi file: from: from mercurial.hgweb import hgweb, wsgicgi application = hgweb(config) to: from mercurial.hgweb import hgweb, hgwebdir, wsgicgi application = hgwebdir(config) Note the added hgwebdir parts there. Here's my hgweb.config file, located in the same directory as hgweb.cgi file: [collections] C:/hg/ = C:/hg/ [web] style = gitweb This now serves my repositories successfully. Hopefully this question will give others some information if they're stumped as I was.

  Read the article

• Problem with System.Diagnostics.Process RedirectStandardOutput to appear in Winforms Textbox in real

  - by Jonathan Websdale

  I'm having problems with the redirected output from a console application being presented in a Winforms textbox in real-time. The messages are being produced line by line however as soon as interaction with the Form is called for, nothing appears to be displayed. Following the many examples on both Stackoverflow and other forums, I can't seem to get the redirected output from the process to display in the textbox on the form until the process completes. By adding debug lines to the 'stringWriter_StringWritten' method and writing the redirected messages to the debug window I can see the messages arriving during the running of the process but these messages will not appear on the form's textbox until the process completes. Grateful for any advice on this. Here's an extract of the code public partial class RunExternalProcess : Form { private static int numberOutputLines = 0; private static MyStringWriter stringWriter; public RunExternalProcess() { InitializeComponent(); // Create the output message writter RunExternalProcess.stringWriter = new MyStringWriter(); stringWriter.StringWritten += new EventHandler(stringWriter_StringWritten); System.Diagnostics.ProcessStartInfo startInfo = new System.Diagnostics.ProcessStartInfo(); startInfo.FileName = "myCommandLineApp.exe"; startInfo.UseShellExecute = false; startInfo.RedirectStandardOutput = true; startInfo.CreateNoWindow = true; startInfo.WindowStyle = System.Diagnostics.ProcessWindowStyle.Hidden; using (var pProcess = new System.Diagnostics.Process()) { pProcess.StartInfo = startInfo; pProcess.OutputDataReceived += new System.Diagnostics.DataReceivedEventHandler(RunExternalProcess.Process_OutputDataReceived); pProcess.EnableRaisingEvents = true; try { pProcess.Start(); pProcess.BeginOutputReadLine(); pProcess.BeginErrorReadLine(); pProcess.WaitForExit(); } catch (Exception ex) { MessageBox.Show(ex.ToString()); } finally { pProcess.OutputDataReceived -= new System.Diagnostics.DataReceivedEventHandler(RunExternalProcess.Process_OutputDataReceived); } } } private static void Process_OutputDataReceived(object sender, System.Diagnostics.DataReceivedEventArgs e) { if (!string.IsNullOrEmpty(e.Data)) { RunExternalProcess.OutputMessage(e.Data); } } private static void OutputMessage(string message) { RunExternalProcess.stringWriter.WriteLine("[" + RunExternalProcess.numberOutputLines++.ToString() + "] - " + message); } private void stringWriter_StringWritten(object sender, EventArgs e) { System.Diagnostics.Debug.WriteLine(((MyStringWriter)sender).GetStringBuilder().ToString()); SetProgressTextBox(((MyStringWriter)sender).GetStringBuilder().ToString()); } private delegate void SetProgressTextBoxCallback(string text); private void SetProgressTextBox(string text) { if (this.ProgressTextBox.InvokeRequired) { SetProgressTextBoxCallback callback = new SetProgressTextBoxCallback(SetProgressTextBox); this.BeginInvoke(callback, new object[] { text }); } else { this.ProgressTextBox.Text = text; this.ProgressTextBox.Select(this.ProgressTextBox.Text.Length, 0); this.ProgressTextBox.ScrollToCaret(); } } } public class MyStringWriter : System.IO.StringWriter { // Define the event. public event EventHandler StringWritten; public MyStringWriter() : base() { } public MyStringWriter(StringBuilder sb) : base(sb) { } public MyStringWriter(StringBuilder sb, IFormatProvider formatProvider) : base(sb, formatProvider) { } public MyStringWriter(IFormatProvider formatProvider) : base(formatProvider) { } protected virtual void OnStringWritten() { if (StringWritten != null) { StringWritten(this, EventArgs.Empty); } } public override void Write(char value) { base.Write(value); this.OnStringWritten(); } public override void Write(char[] buffer, int index, int count) { base.Write(buffer, index, count); this.OnStringWritten(); } public override void Write(string value) { base.Write(value); this.OnStringWritten(); } }

  Read the article

< Previous Page | 491 492 493 494 495 496 497 498 499 500 501 502  | Next Page >