Search Results

Search found 95644 results on 3826 pages for 'one zero'.

Page 497/3826 | < Previous Page | 493 494 495 496 497 498 499 500 501 502 503 504  | Next Page >

  • Need to open port in a router for two internal PC's

    - by Sergio
    I have two PC's behind a comon internet router and one service running in another network that needs to connect with both PC's through internet using a specific port. To avoid dynamic IP issues I have configured NO-IP accounts in both computers and opened the port in their respective Windows Firewalls. My problem is that when I open the port in the router it only allows me to assign it to one of the computers, but not to both of them. Is there any solution to this?

    Read the article

  • Any way to recover ext4 filesystems from a deleted LVM logical volume?

    - by Vegar Nilsen
    The other day I had a proper brain fart moment while expanding a disk on a Linux guest under Vmware. I stretched the Vmware disk file to the desired size and then I did what I usually do on Linux guests without LVM: I deleted the LVM partition and recreated it, starting in the same spot as the old one, but extended to the new size of the disk. (Which will be followed by fsck and resize2fs.) And then I realized that LVM doesn't behave the same way as ext2/3/4 on raw partitions... After restoring the Linux guest from the most recent backup (taken only five hours earlier, luckily) I'm now curious on how I could have recovered from the following scenario. It's after all virtually guaranteed that I'll be a dumb ass in the future as well. Virtual Linux guest with one disk, partitioned into one /boot (primary) partition (/dev/sda1) of 256MB, and the rest in a logical, extended partition (/dev/sda5). /dev/sda5 is then setup as a physical volume with pvcreate, and one volume group (vgroup00) created on top of it with the usual vgcreate command. vgroup00 is then split into two logical volumes root and swap, which are used for / and swap, logically. / is an ext4 file system. Since I had backups of the broken guest I was able to recreate the volume group with vgcfgrestore from the backup LVM setup found under /etc/lvm/backup, with the same UUID for the physical volume and all that. After running this I had two logical volumes with the same size as earlier, with 4GB free space where I had stretched the disk. However, when I tried to run "fsck /dev/mapper/vgroup00-root" it complained about a broken superblock. I tried to locate backup superblocks by running "mke2fs -n /dev/mapper/vgroup00-root" but none of those worked either. Then I tried to run TestDisk but when I asked it to find superblocks it only gave an error about not being able to open the file system due to a broken file system. So, with the default allocation policy for LVM2 in Ubuntu Server 10.04 64-bit, is it possible that the logical volumes are allocated from the end of the volume group? That would definitely explain why the restored logical volumes didn't contain the expected data. Could I have recovered by recreating /dev/sda5 with exactly the same size and disk position as earlier? Are there any other tools I could have used to find and recover the file system? (And clearly, the question is not whether or not I should have done this in a different way from the start, I know that. This is a question about what to do when shit has already hit the fan.)

    Read the article

  • List of LangID KLID input layouts codes for Windows 7/2008

    - by alfa
    There is one similar list for Windows XP/2003 here. Is anybody aware of a version of such list for Windows 2008/7 mentioning valid input locale ID strings for all languages and keyboard layouts? NOTE1: If you are interested to know, I am going to use that ID in the scripts such as this one and the last example in this page NOTE2: In this page, it shows the format of language id as used by the input.dll exported method named SetDefaultLayoutOrTip (Which is probably used by the regarded script engine)

    Read the article

  • How to convert lots of database file from MSSQL 2000 to MSSQL 2005?

    - by Tech
    Hi all, I am moving the SQL Server from MSSQL 2000 to MSSQL 2005, and I found the article in the web like this: http://www.aspfree.com/c/a/MS-SQL-Server/Moving-Data-from-SQL-Server-2000-to-SQL-Server-2005/ It works, but the problem is, it only move database one by one. Because I have so many database, is there any easy way to do so? or is there provides any batches / untitlty allow me to do so? thz u.

    Read the article

  • Could a computer act (dependably) as a wireless router for 200+ clients? [closed]

    - by awkwardusername
    That is, I have a Core 2 Duo E7500 at 2.93GHz, with 2GB memory. I plan to install either Windows Server 2012 or Zeroshell 2.0RC1, and it also (planning to) includes two PCIe Wireless Card Adapters. It also has one ethernet port, and I will connect that to another machine which will be a Database and a Web Server. My plan is to have a corporate level wireless intranet with 200+ clients. I cannot afford to buy routers because I want to operate at zero costs as possible, utilizing my available resources. Is that plan plausible? Also, what minimum specs should my wireless card have? @SvenW: Oh, I meant corporate on the deployment level. I am still an undergraduate and this is more of an educational and expiremental work than an actual project. I got Windows Server 2012 for free though, and this isn't actually for commercial use.

    Read the article

  • Is it possible to rsync your web site to another backup server and use the same .htaccess files?

    - by stephenmm
    I am trying to use rsync to replicate all the files from one web server to another server that could act as a backup if the first one went down. The problem I am having is that the .htaccess file requires the AuthUserFile to have the fully quallified path to the .htpasswd file and I cannot make the paths the same on the two machines. Does anyone know how I might use the same .htaccess file on two different servers? Thanks for any help that can be provided.

    Read the article

  • Setup CENTOS Centralized AUDIT and RSYSLOG server

    - by Warron.French
    Attempting to use these links: Sending audit logs to SYSLOG server or http://wiki.rsyslog.com/index.php/Centralizing_the_audit_log I have been unable to get centralized AUDIT logging to work on my ALL-CentOS network environment. I have 6 workstations dt1...dt6, and the log files are not generated at all and I cannot tell if the messages are being sent from these workstations: dt1..dt6 over to the server (srv1). I have configured the rsyslog.conf on the workstations as shown in the link: Sending audit logs to SYSLOG server, and add the additional touches for generating the logfiles into a separate directory per YEAR/MONTH/DAY (using proper syntax) and into separate HOSTNAME-based_audit.log files. Note: RSYSLOG messaging does appear to work from the workstations over to the server, but the audit logging portion is not working. I am running CentOS-6.5 with RPMs: audit-2.2-4.el6_5.x86_64, audit-libs-2.2-4.el6_5.x86_64, and rsyslog-5.8.10-8.el6.x86_64 I have gotten zero responses from wiki.rsyslog.com and really need this to work. If needed I can send files of one of my workstations and the server to aid in the process. Thanks, Warron

    Read the article

  • how to setup OpenSSH per-user authentication types?

    - by Seaweed
    Hi - I'd like to be able to have one set of users authenticating using public key auth and the other set to use username/password. Is this possible in OpenSSH on Linux? If so how do I go about it? Right now, I'm stuck with only having one option as far as I can see in /et/ssh/sshd_config - it's either PAM or PublicKey authentication...

    Read the article

  • Which is prefered internet security + Antivirus solution for Windows, with good detection rate? [clo

    - by metal gear solid
    Possible Duplicate: Free antivirus solutions for Windows Which is the best internet security + Antivirus solution for Windows? free/opensource or commercial it doesn't matter I need best solution. Is Kaspersky best ? or any other? http://www.kaspersky.com/kaspersky_internet_security Award-winning technologies in Kaspersky Internet Security 2010 protect you from cybercrime and a wide range of IT threats: * Viruses, Trojans, worms and other malware, spyware and adware * Rootkits, bootkits and other complex threats * Identity theft by keyloggers, screen capture malware or phishing scams * Botnets and various illegal methods of taking control of your PC or Netbook * Zero-day attacks, new fast emerging and unknown threats * Drive-by download infections, network attacks and intrusions * Unwanted, offensive web content and spam

    Read the article

  • Finding Missing UDP Frames Using Wireshark + Custom Dissector (for CQS)

    - by John Dibling
    How do you use Wireshark to identify missing UDP frames? I have written a custom dissector for the CQS feed (reference page). One of our servers gaps when receiving this feed. According to Wireshark, some UDP frames are never received. I know that the frames were sent because all of our other servers are gap-free. A CQS frame consists of multiple messages, each having its own sequence number. My custom dissector provides the following data to Wireshark: cqs.frame_gaps - the number of gaps within a UDP frame (always zero) cqs.frame_first_seq - the first sequence number in a UDP frame cqs.frame_expected_seq - the first sequence number expected in the next UDP frame cqs.frame_msg_count - the number of messages in this UDP frame And I am displaying each of these values in custom columns, as shown in this screenshot: A typical CQS log will consist of millions of rows, so I can't just eyeball it. Is there any way I can get Wireshark to tell me which frames are missing?

    Read the article

  • How do I lower idle cpu usage in ubuntu linux? Gnome or KDE Variants

    - by Jasen
    My question comes from a kde desktop currently, but it also happens with the gnome instance. When just sitting there, with only the cpu monitor widget running. no open windows, no background processes other than the desktop, my cpu is at ~20%. I wanna know how to fix this, and possibly get better performance out of it. When running my windows side, the cpu will sit at zero, and i generally load new programs about 400ms faster. With windows 7 being as slow as it is, this is not acceptable. and the widget is only set to check every 500ms, so im almost completely sure its not the widget. My system is a Gateway nv 53 amd 2.0 ghz turion with 4 gb of installed ram, and 500 gb hd. both linux and windows are 64 bit. average ram use on either system is about 1.4 gb for just the os

    Read the article

  • Is there an emoticon to express irony?

    - by Dimitri C.
    I use irony rather often, but in written texts such as email I'm often afraid that it might be misinterpreted by the reader. Therefore I'd like to use an emoticon to make the irony explicit, but I'm not sure which one is most often used for this purpose. Which one would be most suited?

    Read the article

  • Apache Tomcat 6.0.29 startup causing Win XP SP3 reboot

    - by Liam
    Some of our Windows XP Developer machines die (black screen - no ping) when starting up Tomcat from a console. This only happens if the Tomcat debug console window is displayed (not minimised). When minimised, the startup / run is successful. I've checked for Tomcat logs and the crash sessions produce empty (zero bytes) tomcat log files. No system logs exist and no crash dump is created even though this is enabled in the Windows settings. The machine is dual screen and another machine with the same image has the same issue. The only clue is just before the crash, one of the monitors the system reports "Cannot display video mode 1280x1024" (approximate error, didn't write it down). Is there a way I can get Windows to produce log files of this crash session? Beyond running Tomcat as a service / minimised window, how can I fix (or even investigate)?

    Read the article

  • Anyone know a good web-based file upload package?

    - by Ted Wexler
    Basically, what I'm looking for is a place for either one of our end users to be able to upload a file to this package, after either receiving a code from one of our support engineers or vice-versa(our engineers upload a file and send a code/link/something to end user) I've spent a bunch of time googling this, I found this: http://turin.nss.udel.edu/programming/dropbox2/, but the code there scares me, and it also doesn't render properly using PHP 5.3(uses short tags, who knows what else.) Does anyone have any recommendations?

    Read the article

  • IP NAT pool range

    - by hfranco
    When is it necessary to setup a pool of more than one address? So if I have this ip pool range: ip nat pool demo 72.32.11.65 72.32.11.66 netmask 255.255.255.252 What's the difference if I just have one address? ip nat pool demo 72.32.11.65 72.32.11.65 netmask 255.255.255.252

    Read the article

  • Small website on Amazon EC2 Linux: a single large instance or more small instances in load balancing?

    - by Enrico Detoma
    I need to run a small website with a JSON webservice on Amazon EC2 Linux. The largest number of requests come from the JSON webservice, which provides some load in terms of MySQL queries. I'm trying to decide between two choices: A single large instance (Ubuntu 12.04 64-bit) with full LAMP stack or One or two small instances (Ubuntu 12.04 64-bit) with Apache/PHP only One small instance dedicated to MySQL (or RDS) Which setup would you consider to be more performant?

    Read the article

  • Primary/secondary ethernet interfaces via NetworkManager in Ubuntu 9.10

    - by Josh
    I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local... EDIT: Here's my routing table: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 172.16.151.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 172.16.30.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.1.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 172.16.30.2 0.0.0.0 UG 0 0 0 eth0 0.0.0.0 10.1.0.1 0.0.0.0 UG 0 0 0 eth1 I want the 172.16.30.2 network to be the primary one and the 10.1.0.0 network to be the secondary one. EDIT2: My nameservers are also incorrect. It seems like Ubuntu is bringing the networks up in order, eth0, then 1, then 2, and the DHCP information from eth1 is overriding eth0, and eth2 is overriding eth1. How can I reverse this so the DHCP information from eth0 is the "master"? EDIT3: This seems to be an issue with Gnome's NetworkManager.

    Read the article

  • linux macvlan - stop from broadcasting hostname

    - by staticfloat
    I am trying to simulate two different computers on one box, using the macvlan module (which is awesome, by the way) but I have one small problem; When I create the macvlan Ubuntu 11.10 very helpfully starts broadcasting its hostname on both interfaces, creating an amazing amount of confusion for everything that deals with hostnames. Does anyone know how to stop ubuntu from advertising its hostname on a certain interface? Thanks!

    Read the article

  • Is it possible to get a list of running processes with a Cloudwatch Alarm?

    - by jtalarico
    We have an EC2 instance (Ubuntu) that has a few java-based applications and lately we're getting hit with high CPU utilization spikes that trigger one of our Cloudwatch alarms. By the time we get into the server to look at the cpu utilization, things have calmed down. What we'd love to see in one of the alarm emails is a list of running processes and their cpu utilization(%) at the time of the alarm. Is this even possible?

    Read the article

  • Hyperic HQ metrics not working

    - by Robin Weston
    I am having a problem with Hyperic HQ. Several metrics, some in IIS 6.x (Request Execution Time, Request Wait Time) and some in .NET 2.0 (Bytes in all Heaps, Exceptions Thrown per Minute), always show 0. If I view perfmon on the server itself I can see that the counters have values greater than zero. There are some metrics that work fine, such as Total Get Requests per Minute and the other IIS defaults. I have looked in the server logs but nothing obvious shows up. Please advise. Am happy to find more information if required.

    Read the article

  • My way of Comparing CPUs

    - by abbasi
    There are many types of CPUs, like Pentiume, Atom, core 2 duo, core iX (X = 3,5, ....), But I always don't look at them this way! I always look at their speed which in GHZ unit and then compare them with each other. For example when some CPU is in type of 'X' with 2 GHZ of speed and another one is in type of 'Y' with 2.2 GHZ of speed, I say the second one ('Y') has better speed and also better performance. Is it a correct way? Thanks

    Read the article

< Previous Page | 493 494 495 496 497 498 499 500 501 502 503 504  | Next Page >