Search Results

Search found 16903 results on 677 pages for 'single responsibility'.

Page 498/677 | < Previous Page | 494 495 496 497 498 499 500 501 502 503 504 505  | Next Page >

• Network Load Balancing and AnyCast Routing

  - by user126917

  Hi All can anyone advise on problems with the following? I am planning on installing the following setup on my estate: I have 2 sites that both have a large amount of users. Goals are to keep things simple for the users and to have automatic failover above the database level. Our Database will exist at the primary site and be async mirrored to the secondary site with manual failover procedures.The database generate sequential ID's so distributing it is not an option. I plan to site IIS boxes at both sites with all of the business logic on them and heavy operations. The connections to SQL will be lightweight and DB reads will be cached on IIS. On this layer I plan to use Windows network load balancing and have the same IP or IPs across all IIS boxes at both sites. This way there will be automatic failover and no single point of failure. Also users can have one web address regardless of which site they are in automatically be network load balanced to their local IIS. This is great but obviously our two sites are on different subnets and as this will be one IP address with most of our traffic we can't go broadcasting everything across the link between the sites. To solve this problem we plan to use AnyCast routing over our network layer to route the traffic to the most local box that is listening which will be defined by the network load balancing. Has anyone used this setup before? Can anyone think of any issues with this? Also some specifics I can't find anywhere at the moment. If my Windows box is assigned an IP and listening on that IP but network load balancing is not accepting specific traffic then will AnyCast route away from that? Also can I AnyCast on a socket level?

  Read the article

• repo sync "CyanogenMod/android_prebuilt" size and resume capability.?

  - by james

  I'm downloading CyanogenMod-10.1 source on a low speed broadband. About 4GB of source is downloaded . In that 4GB, there is a big project "CyanogenMod/android_frameworks_base" which alone took 1GB of download without any interruption. Ok now, after 4GB of download, my internet got disconnected and I had to stop (ctrl + z) repo sync while it was downloading the project "CyanogenMod/android_prebuilt". Before I stopped repo sync the android_prebuilt got downloaded till 250MB and is at 42percent. I checked the working folder and there is a file "tmp_pack_df5CKb" of size 250MB in the path "$WORKING_DIR/.repo/projects/prebuilt.git/objects/pack/" . Then I restarted repo sync and it was downloading the android_prebuilt project. But I'm not sure if it was downloading from start or resuming from 250MB. While downloading this time , the previous "tmp_pack_df5CKb" isn't deleted and the content is being downloaded to a new file "tmp_pack_HPfvFG". I heard repo sync cannot be resumed for a project. But here, since the previous file isn't deleted I want to ask if android_prebuilt is resuming or downloading from start again? Now that my high speed internet is over (current speed 256kbps), I'm not sure if I can download the remaining ~4GB if single project is in size 500 MB.

  Read the article

• What is the IPv6 equivalent to IPv4 RFC1918 addresses?

  - by Kumba

  Having a hard time wrapping my head around IPv6 here. A lot of the lingo seems targeted at enterprise-level IPv6 deployments, discussing link-local, site-local, global unicast, scopes, etc. Not a lot of solid information on really small networks, like home networks. I want to check my thinking and make sure I am getting the correct translations from IPv4-speak to IPv6-speak. The first question is, what's the equivalent of RFC1918 for IPv6? Initial searches suggested there was no equivalent. Then I stumbled upon Unique Local Addresses (RFC4193), and that states that all ULA's should be assigned the prefix fc00, followed by a 40-bit random number in the routing prefix. This random number is to "prevent collisions when two IPv6 networks are interconnected" -- again, another reference to an enterprise-level function. If I have a small local LAN at home, numbered using 192.168.4.0/24, what's my equivalent in IPv6's ULA scope? Assuming I will never, ever, tie that IPv6 address into the real internet (a router will NAT & firewall it), can I ignore the RFC to an extent and go with fc00::4:0/120? It also seems that any address in fc00::/7 are to be globally routable. Does this mean I'll need extra protections so my router would not automatically start advertising these private IPv6 addresses to the world? Second question, what's this link-local thing? Reading suggests a default-assigned address in the fe80::/10 range that has the last 64bits of the address comprised of the interface's MAC address. Seems to be required, too, but I'm annoyed by the constant discussion of it in relation to enterprise networks. Third question, what is scope id for? Seems to be yet another term tossed around in relation to enterprise networks, especially when interconnecting them, but almost no explanation on the smaller home network level. Can I see a scope ID AND CIDR notation used together? I.e., fc00::4:0/120%6, or are scope IDs only supposed to be applied to a single /128 IPv6 address?

  Read the article

• my X server doesn't load a module called "glx", but my video drivers seem to be installed

  - by rumtscho

  I just got a new, very wide monitor (2560x1440) and there is no sense maximizing my applications. So I installed Compiz Config Settings Manager and enabled Grid. Nothing happened, the shortcuts don't move application windows. Went to System - Preferences - Appearance, the Visual effects tab. It at "disabled". When I try to set them to "normal" or "extra", a message box appears telling me that it's searching for video drivers, then disappears, and I get an error message "Desktop effects could not be enabled". I opened Xorg.0.log, and had errors there: (EE) Failed to load /usr/lib/xorg/modules/extensions//libglx.so (II) UnloadModule: "glx" (EE) Failed to load module "glx" (loader failed, 7) (II) LoadModule: "extmod" Going to Administration - System - Hardware drivers, it said that there are no available and/or installed hardware drivers. But apt-get said that it cannot install nvidia-glx-185, as it is already installed. Googling my error message suggested that I install and run something called envyng. This let me install the nvidia drivers again, and now I can see in the Hardware Drivers window that they are installed and active. But the error message in Xorg.0.log remains, and I still cannot enable the Compiz effects or use Grid. Now, I don't have enough Linux experience to understand if this is a single cause-effect-chain of problems, or three independent ones, but I'd appreciate help for any of them. I am running Ubuntu 9.10, the video card is a GeForce 7600GS.

  Read the article

• DNS: how to get local server to superimpose results over authoritative server?

  - by growse

  I've got a domain for which the DNS I control, and is hosted on the internet. I also have a NAT'd internal network (192.168.0.0/24) which has internet access, and which I also control. On this internal network, I also have a DNS resolver. DNS software on both is PowerDNS. What I want to be able to do is for the DNS resolver on the internal network to be able to add/change records of queries and results that come down from the authoritative server. For example, the authoritative server might have a single record for animal.example.com: animal.example.com. IN AAAA 2001:140:283::1 However, I'd like it so that when internal clients do a dns lookup for animal.example.com, they might get back the following: animal.example.com. IN AAAA 2001:140:283::1 animal.example.com. IN A 192.168.0.2 Obviously, I could set up the internal DNS server to pretend to be authoritative for example.com, but that would require a fair bit of effort to keep the main DNS server and the internal DNS server in sync for the records which are the same between both. If the internal DNS server could somehow be made a slave of the main DNS server, but also have the provision to add its own results in, that would be ideal. Is this possible?

  Read the article

• How to determine the Kerberos realm from an LDAP directory?

  - by tstm

  I have two Kerberos realms I can authenticate against. One of them I can control, and the other one is external from my point of view. I also have an internal user database in LDAP. Let's say the realms are INTERNAL.COM and EXTERNAL.COM. In ldap I have user entries like this: 1054 uid=testuser,ou=People,dc=tml,dc=hut,dc=fi shadowFlag: 0 shadowMin: -1 loginShell: /bin/bash shadowInactive: -1 displayName: User Test objectClass: top objectClass: account objectClass: posixAccount objectClass: shadowAccount objectClass: person objectClass: organizationalPerson objectClass: inetOrgPerson uidNumber: 1059 shadowWarning: 14 uid: testuser shadowMax: 99999 gidNumber: 1024 gecos: User Test sn: Test homeDirectory: /home/testuser mail: [email protected] givenName: User shadowLastChange: 15504 shadowExpire: 15522 cn: User.Test userPassword: {SASL}[email protected] What I would like to do, somehow, is to specify per-user basis to which authentication server / realm the user is authenticated against. Configuring kerberos to handle multiple realms is easy. But how to I configure other instances, like PAM, to handle the fact that some users are from INTERNAL.COM and some from EXTERNAL.COM? There needs to be an LDAP lookup of some kind where the realm and the authentication name is fetched from, and then the actual authentication itself. Is there a standardized way to add this information to LDAP, or look it up? Are there some other workarounds for a multi-realm user base? I might be ok with a single realm solution, too, as long as I can specify the user name - realm -combination for the user separately.

  Read the article

• Monospace font which supports at least both of Korean hangul and the Georgian alphabet?

  - by hippietrail

  Being both a language enthusiast and a programmer, I find myself often doing programming or text processing involving foreign language alphabets and scripts. One annoyance however is that CJK fonts (those which support Chinese, Japanese, and/or Korean) usually only contain glyphs for Latin, Greek, and Cyrillic at best. Often the Asian glyphs will be beautiful but the other glyphs can be quite ugly. Just as often in text editors you can only choose a single font, not one for CJKV and one for other, which will be each used for rendering the appropriate characters. Korean is one of the languages I'm most interested in currently. I only need hangul / hangeul for monospaced editing, hanja isn't common enough to be a problem. Another of the languages I'm currently involved in is Georgian, which has its own alphabet which is a little exotic but has pretty good support in common fonts on Windows and *nix. But I am as yet unable to find a font with good Korean glyphs and also Georgian glyphs. My editor of choice is gVim, so an answer telling me how to set it to use two fonts together would be just as good. Currently I'm using it mostly under Windows 7 so a vim-specific solution would be needed rather than a *nix-specific solution.

  Read the article

• How do I migrate Exchange 2007 to new hardware?

  - by Graeme Donaldson

  As per my previous question, I have an Exchange 2007 box which is also a DC. Since I can't demote it while Exchange is installed, I want to move Exchange to a different server. Does anyone have any articles, tips or experiences to share on this? The last time I did this it was with Exchange 2003 and even that is a little rusty in my head. The setup is a single Exchange 2007 Hub/Edge/Mailbox/CAS server. Its currently on Windows Server 2008, I can migrate it to the same OS, or I can go to 2008 R2, I'm not really picky on that. We're running OWA/ActiveSync/POP3(S)/IMAP(S) for client access. I already have another fully functional DC/GC/DNS box in the same site and clients in the site are already using that for DNS. It's also the preferred site bridgehead for AD replication. Update: After reading Evan's answer I realised that my original question wasn't worded correctly. I'm not looking to do a swing migration, I actually need to move Exchange completely over to a new box. I have done swing migrations in the past, i.e. moving over to a temporary box and back to the original hardware afterwards, and I'm not really sure why I used that term in the original question since it's not what I intended. Any tips?

  Read the article

• Remote Socket Read In Multi-Threaded Application Returns Zero Bytes or EINTR (104)

  - by user39891

  Hi. Am a c-coder for a while now - neither a newbie nor an expert. Now, I have a certain daemoned application in C on a PPC Linux. I use PHP's socket_connect as a client to connect to this service locally. The server uses epoll for multiplexing connections via a Unix socket. A user submitted string is parsed for certain characters/words using strstr() and if found, spawns 4 joinable threads to different websites simultaneously. I use socket, connect, write and read, to interact with the said webservers via TCP on their port 80 in each thread. All connections and writes seems successful. Reads to the webserver sockets fail however, with either (A) all 3 threads seem to hang, and only one thread returns -1 and errno is set to 104. The responding thread takes like 10 minutes - an eternity long:-(. *I read somewhere that the 104 (is EINTR?), which in the network context suggests that ...'the connection was reset by peer'; or (B) 0 bytes from 3 threads, and only 1 of the 4 threads actually returns some data. Isn't the socket read/write thread-safe? I use thread-safe (and reentrant) libc functions such as strtok_r, gethostbyname_r, etc. *I doubt that the said webhosts are actually resetting the connection, because when I run a single-threaded standalone (everything else equal) all things works perfectly right, but of course in series not parallel. There's a second problem too (oops), I can't write back to the client who connect to my epoll-ed Unix socket. My daemon application will hang and hog CPU 100% for ever. Yet nothing is written to the clients end. Am sure the client (a very typical PHP socket application) hasn't closed the connection whenever this is happening - no error(s) detected either. Any ideas? I cannot figure-out whatever is wrong even with Valgrind, GDB or much logging. Kindly help where you can.

  Read the article

• Network latency and speed of light

  - by James

  This was kinda of covered by the following Is minimum latency fixed by the speed of light? , but i would like to add the follow up a bit. The scenario is as follows; we have two opposing sites one on the West Coast of the US and one in Ireland. The customer is in central Europe, and has requested a latency test. Ireland gives responses of ~65-70ms. However the West Coast guys claim to be faster with a response of 60ms. Now a quick check says that light in fiber would take about 42ms to make the trip to the States and 8.5ms to Ireland. So obviously this is a single hop and does not include routers, switches, firewalls, protocol overhead etc. Would I be right to call BS on their figures? As a final note I tested a ping to Google IP address that was allegedly on the west coast from a site that covered a similar distance and was amazed to get a response time of 20ms. Suggesting ICMP packets that travel twice the speed of light. So A) what am I missing B) Am I right to suspect shenanigans? UPDATE: Guys thanks so far for your help and I have been reading various previous questions on this. About 5 years I had an issue where the hop from the UK to Ireland added 10ms of latency no matter what we did. In the end I moved the servers; So imagine my surprise when I have guys that claim they are 5ms faster with a transatlantic trip. So again should I call BS? Oh and assume both sites are normal mortals that don't have access to Google magical routing, warp dives or flux capacitors. :)

  Read the article

• tail -f and then exit on matching string

  - by Patrick

  I am trying to configure a startup script which will startup tomcat, monitor the catalina.out for the string "Server startup", and then run another process. I have been trying various combinations of tail -f with grep and awk, but haven't got anything working yet. The main issue I am having seems to be with forcing the tail to die after grep or awk have matched the string. I have simplified to the following test case. test.sh is listed below: #!/bin/sh rm -f child.out ./child.sh > child.out & tail -f child.out | grep -q B child.sh is listed below: #!/bin/sh echo A sleep 20 echo B echo C sleep 40 echo D The behavior I am seeing is that grep exits after 20 seconds , however the tail will take a further 40 seconds to die. I understand why this is happening - tail will only notice that the pipe is gone when it writes to it which only happens when data gets appended to the file. This is compounded by the fact that tail is to be buffering the data and outputting the B and C characters as a single write (I confirmed this by strace). I have attempted to fix that with solutions I found elsewhere, such as using unbuffer command, but that didn't help. Anybody got any ideas for how to get this working how I expect it? Or ideas for waiting for successful Tomcat start (thinking about waiting for a TCP port to know it has started, but suspect that will become more complex that what I am trying to do now). I have managed to get it working with awk doing a "killall tail" on match, but I am not happy with that solution. Note I am trying to get this to work on RHEL4.

  Read the article

• sporadic routing to another website when opening a common url

  - by user226098

  I have a strange problem in our office: Sometimes when opening a url from one of our projects random url in any browser not the right website shows up but some other website. In most of the cases it redirects to google.com with some parameters like https://www.google.de/?gfe_rd=cr&ei=krOOU8_kGcSKswadyYDQBw&gws_rd=ssl or just the ugly google 404 page). But today it remains on the origial url but shows up the the content of http://debug.netdna-cdn.com/. This happens about 1 time a week and for no apparent reason. Even stranger it only occurs on a single pc in the network. It now happens on two different computers in the network. Both use windows 8. The problem cannot be fixed by clearing the browser cache but by rebooting the pc or using ipconfig /flushdns. So I think it has something to do with the dns cache of the machine. But I have no idea what the reason is for this and how i can figure out how to solve it. Any ideas?

  Read the article

• open-source LAMP package for simple accouting and receiving?

  - by user26664

  Hello. I am involved with a computer-based charity where we take donation of old equipment, often recycle it, mostly rehabilitate it and make it available through grants and 'adoptions', and sell some items. What we're looking for is a LAMP package that can handle our records of donations of equipment, print receipts for donators, and also track our thrift store sales with receipts. Donators will want receipts of their donations for tax deduction purposes. We'll want to print reports of incoming items from time to time, say monthly and yearly. For the thrift store, we'll also need receipts for that, reports of cash, especially for reconciling cash drops, and also reports of items sold from time to time. I'm thinking this might be a single package, but it might be two. We don't want to track our shop inventory with either of these programs -- that's another program/project. We just need to know what was donated and what was sold. It must be open source, and ideally we'd like it to run on LAMP -- Linux, Apache, MySQL, PHP, but we will consider other open-source platforms.

  Read the article

• Server 2008R2 in Extra Small Windows Azure Instance?

  - by Shawn Eary

  Windows Azure hosting for an Extra Small (XS) Windows VM seems to come out to be about $10 a month right now. I think this XS instance gives you the equivalent of a 1 GHZ CPU with 768MB of RAM. I think the minimum requirements for Server 2008 is 1GHZ CPU with 512MB of RAM. Also, I think the minimum requirements for SQL Server Express is 1GHZ CPU with 256 MB of RAM and that the minimum requirements for Team Foundation Server Express 11 Beta is 2.2 GHZ CPU with 1 Gig of RAM (this 2.2 GHZ part could be a problem for my 1 GHZ XS VM...). Given the performance of the XS Azure instance, would I be able to install: a very basic MVC web site; a free instance of SQL Server Express; a free single user instance of Team Foundation Server Express 11 Beta and run the XS VM instance without serious crashing? I know there are other Shared WebHost providers that can provide these features for me, but those hosting providers have the following disadvantages: They sometimes cost a lot of money after all of the "addons" are in place They probably don't provide the level of security and employee integrity that Microsoft can provide They don't provide the total control that an Azure VM seems to provide

  Read the article

• Can I still restore partition table?

  - by Johannes Lund

  Once I was going to resize partitions on my Mac HD from Bootcamp. I changed my mind and was going to quit, but apparently I hit a button, which made every single mac partion dissapear, and windows 7 refused to restart and be reinstalled. The 1 TB large HD consists of 3 partions, I believe. Since I can't see their actual size (except bootcamp), this is how I recall it. Macintosh HD about 500GB (Somewhere around 700GB according to disk utillity, but 500 according to Finder, and 500GB was all I could access.) Lion Recovery disk Bootcamp 293.36 GB To fix this I connected my mac via target disk mode to a pc and ran TestDisk. However this is the results: Since I Don't have 10 reputation I cant post the image showing the testdisk results, so I post a link instead hoping it is ok. The two mac partitions' sizes are completely wrong, and BOOTCAMP isn't showing. I tested using disk utilities from the snow leopard dvd. There there is one 293.36 GB Mac OS Extended partition. Before I had the firewire cable for target disk mode I tried reinstalling windows. Without success I tried again formating BOOTCAMP. Was that a bad thing to do? Could it have overwritten data from Macintosh HD? Unfortunately I have no backup. I could bring it to some kind of computer repair firm though.

  Read the article

• VMWare Setup with 2 Servers and a DAS (DELL MD3220)

  - by Kumala

  I am planning to use a VMWare based setup consisting of two VMWare servers (2 CPU, 256GB Memory) and a DAS (DELL MD3220 with 24x900GB disks). The virtual machines will be half running MS SQL databases (Application, Sharepoint, BI) and the other half of the VM will be file services, IIS. To enhance the capacity of the storage, we'll be adding a MD1220 enclosure with another 24x900GB to the MD3220. Both DAS will have 2 controllers. Our current measured IOPS is 1000 IOPS average, 7000 IOPS peak (those happen maybe twice per hour). We are in the planning phase now and are looking at the proper setup of the disks. The intention is to setup up both DAS one of the DAS with RAID 10 only and the other DAS with RAID 5. That will allow us to put the applications on the DAS that supports the application performance needs best. Question is how best to partition the two DASs to get best possible IOPS/MBps, each DAS will have to have 2 hot spares? For the RAID 5 Setup: Generally speaking, would it be better to have one single disk group across all 22 disks (24 - 2 hot spares) with both controllers assigned to the one disk group or is it better to have 2 disk groups each 11 disks, assigned to one of the two controllers? Same question for the RAID 10 setup: The plan is: 2 disks for logs (Raid 1), 2 Hotspare and 20 disks for RAID 10. Option 1: 5 * 4 disks (RAID 10), with two groups assigned to 1 controller and 3 groups to the other controller Option 2: One large RAID 10 across all the disks and have both controllers assigned to the same group? I would assume that there is no right or wrong, but it all depends very much on the specific application behaviour, so I am looking for some general ideas what the pros and cons are of the different options. IF there are other meaningful options, feel free to propose them.

  Read the article

• Switching between taskbar tasks sequentially

  - by Doug Kavendek

  In Firefox and some other tabbed interfaces, I can use Ctrl-PgUp/Down to cycle through tabs sequentially, based on their order in the tab list. I associate what is what based almost entirely on its position along the tab bar and what is next to what, so this is extremely useful for the way I keep track of things in my head. However, I haven't been able to find an equivalent for actual taskbar items in Windows, such that with a single shortcut will switch focus to the task item either to the left or the right of the current task in focus. There's a lot of existing shortcuts that I use (Alt-Tab, Ctrl-Esc, and their counterparts), but these use the window manager's stacking order, so it always changes based on what you've switched between in the past, and so their usefulness generally only lies in switching between two apps -- above that, I just can't keep that kind of stack in my head. The closest shortcut I've found is Winlogo-Tab, but it only moves a selector on the taskbar, so you have to hit space after moving it, and it also seems to originate the selector from the leftmost item every time (rather than relative to the current item). Am I just a weirdo and will have to write my own app to perform these actions?

  Read the article

• Turn Excel spreadsheet into a formula

  - by ?????? ??????????

  I have an Excel spreadsheet that has a complex computation that is not trivial to turn into a macro or a single-cell formula. The spreadsheet has a about 10 different inputs (values a human enters in different cells of the spreadsheet) and then it outputs 5 independent calculations (in different 5 cells) based on that input. There calculation is using some pre-entered data in the spreadsheet (about 100 different constants) and doing some look-ups on them. Now I would like to use this whole spreadsheet as a formula on a different spreadsheet to calculate a set of input values and produce the corresponding set of output values. Imagine this as creating different table with 10 columns for the input variables and 5 columns for the outputs, then copying each input into the other spreadsheet and copying back the output in the results table. For instance: - A1, A2, A3,... A10 are cells where someone enters values - through a series of calculations B1, B2, B3, B4 and B5 are updated with some formulas Can I use the whole series of calculations from A1..A10 into B1..B5 without creating one massive huge formula or a VBA macro? I want to have a set of input values in 100 rows from A100, B100, C100,... J100 onward. Then do some Excel magic that will: 1. copy the values from A100...J100 into A1 to A10 2. wait for the result to appear in B1 to B5 3. copy the values from B1 to B5 into K100 to O100 4. repeat steps 1 to 3 for all rows from 100 to 150

  Read the article

• Microsoft Home Use Program - use more than one computer

  - by kristof

  I purchased a copy of MS Office through Microsoft Home Use Program (HUP) It basically allows you get a very cheap copy for home use if your employer owns the licence. My question is: Can I install it on more than one PC/laptop at home? I could not find anything in FAQ Thank you EDIT I was installing Office 2010 I found the following in the EULA: MICROSOFT SOFTWARE LICENSE TERMS .... 2 INSTALLATION AND USE RIGHTS. a. One Copy per Device. You may install one copy of the software on one device. That device is the “licensed device.” b. Licensed Device. You may only use one copy of the software on the licensed device at a time. c. Portable Device. You may install another copy of the software on a portable device for use by the single primary user of the licensed device. Here is the full copy of the licence

  Read the article

• Use Apache authentication + authorization to control access to Subversion subdirectories

  - by Stefan Lasiewski

  I have a single SVN repo at /var/svn/ with a few subdirectories. Staff must be able to access the top-level directory and all subdirectories within it, but I want to restrict access to subdirectories using alternate htpasswd files. This works for our Staff. <Location /> DAV svn SVNParentPath /var/svn AuthType Basic AuthBasicProvider ldap # mod_authnz_ldap AuthzLDAPAuthoritative off AuthLDAPURL "ldap.example.org:636/ou=people,ou=Unit,ou=Host,o=ldapsvc,dc=example,dc=org?uid?sub?(objectClass=PosixAccount)" AuthLDAPGroupAttribute memberUid AuthLDAPGroupAttributeIsDN off Require ldap-group cn=staff,ou=PosixGroup,ou=Unit,ou=Host,o=ldapsvc,dc=example,dc=org </Location> Now, I am trying to restrict access to a subdirectory with a separate htpasswd file, like this: <Location /customerA> DAV svn SVNParentPath /var/svn # mod_authn_file AuthType Basic AuthBasicProvider file AuthUserFile /usr/local/etc/apache22/htpasswd.customerA Require user customerA </Location> I can use Firefox and curl to browse to this folder fine: curl https://svn.example.org/customerA/ --user customerA:password But I cannot use check out this SVN repository: $ svn co https://svn.example.org/customerA/ svn: Repository moved permanently to 'https://svn.example.org/customerA/'; please relocate And on the server logs, I get this strange error: # httpd-access.log 192.168.19.13 - - [03/May/2010:16:40:00 -0700] "OPTIONS /customerA HTTP/1.1" 401 401 192.168.19.13 - customerA [03/May/2010:16:40:00 -0700] "OPTIONS /customerA HTTP/1.1" 301 244 # httpd-error.log [Mon May 03 16:40:00 2010] [error] [client 192.168.19.13] Could not fetch resource information. [301, #0] [Mon May 03 16:40:00 2010] [error] [client 192.168.19.13] Requests for a collection must have a trailing slash on the URI. [301, #0] My question: Can I restrict access to Subversion subdirectories using Apache access controls? DocumentRoot is commented out, so it's not clear that the FAQ at http://subversion.apache.org/faq.html#http-301-error applies.

  Read the article

• iptables to block non-VPN-traffic if not through tun0

  - by dacrow

  I have a dedicated Webserver running Debian 6 and some Apache, Tomcat, Asterisk and Mail-stuff. Now we needed to add VPN support for a special program. We installed OpenVPN and registered with a VPN provider. The connection works well and we have a virtual tun0 interface for tunneling. To archive the goal for only tunneling a single program through VPN, we start the program with sudo -u username -g groupname command and added a iptables rule to mark all traffic coming from groupname iptables -t mangle -A OUTPUT -m owner --gid-owner groupname -j MARK --set-mark 42 Afterwards we tell iptables to to some SNAT and tell ip route to use special routing table for marked traffic packets. Problem: if the VPN failes, there is a chance that the special to-be-tunneled program communicates over the normal eth0 interface. Desired solution: All marked traffic should not be allowed to go directly through eth0, it has to go through tun0 first. I tried the following commands which didn't work: iptables -A OUTPUT -m owner --gid-owner groupname ! -o tun0 -j REJECT iptables -A OUTPUT -m owner --gid-owner groupname -o eth0 -j REJECT It might be the problem, that the above iptable-rules didn't work due to the fact, that the packets are first marked, then put into tun0 and then transmitted by eth0 while they are still marked.. I don't know how to de-mark them after in tun0 or to tell iptables, that all marked packet may pass eth0, if they where in tun0 before or if they going to the gateway of my VPN provider. Does someone has any idea to a solution? Some config infos: iptables -nL -v --line-numbers -t mangle Chain OUTPUT (policy ACCEPT 11M packets, 9798M bytes) num pkts bytes target prot opt in out source destination 1 591K 50M MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 MARK set 0x2a 2 82812 6938K CONNMARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 CONNMARK save iptables -nL -v --line-numbers -t nat Chain POSTROUTING (policy ACCEPT 393 packets, 23908 bytes) num pkts bytes target prot opt in out source destination 1 15 1052 SNAT all -- * tun0 0.0.0.0/0 0.0.0.0/0 mark match 0x2a to:VPN_IP ip rule add from all fwmark 42 lookup 42 ip route show table 42 default via VPN_IP dev tun0

  Read the article

• adding a custom user folder on Ubuntu

  - by Narcolapser

  Question: How do you add a custom folder to the collection of user folders that come with Ubuntu? Info: I just loaded my netbook with Ubuntu Desktop 10.04LTS (Desktop because it is an aspire one and the Apocalypse seems to follow when ever i try to install netbook remix onto it). It comes with standard folders like Documents, Music, Pictures, Downloads(though this one doesn't appear until you actually download something), Videos, etc etc. These are handly little folders because they have little symbols on them and are nicely located in my file browser. it is basically like the folder lay out the windows had in vista. I do a lot of little programing on this computer so i have a folder in which i keep all these single kb code files. Obviously named "Code" that I keep in my home folder. But I would really like to it over listed next to my other user folders. In summary, how do you add a folder to the listing on the file browser. And, if possible, how do you give it an icon? (I understand fully that I will probably have to make said Icon) those two things are what I'm seeking to do. ~n P.s. please correct me if I'm using the wrong name. I just guessed and called them "User Folders" because they were folders the user uses. made sense. but if they have another name like "libraries" please say so. Thanks

  Read the article

• Removing/modifying LDAP objectclasses/attributes using olc

  - by Foezjie

  I'm having trouble using openldap's olc to modify a schema without shutting down the server. To test some things out, I made the following schema: objectIdentifier tests orgUlyssisOID:4 objectIdentifier testAttribute tests:1 objectIdentifier testObjectClass tests:2 attributeType ( testAttribute:1 NAME 'attr1' DESC 'attribuut 1' SYNTAX '1.3.6.1.4.1.1466.115.121.1.40' ) attributeType ( testAttribute:2 NAME 'attr2' DESC 'attribuut 2' SUP userPassword SINGLE-VALUE ) objectclass ( testObjectClass:1 NAME 'class1' DESC 'objectclass 1' SUP top STRUCTURAL MUST (attr1 $ attr2 ) ) And added it to a new schema called test. (cn={9}test.ldif in cn=schema). Now I can't seem to figure out how to delete class1 from that schema. I use the following LDIF (and tried lots of variations too, to no avail) dn : cn={9}test,cn=schema,cn=config changetype: modify delete: olcObjectClasses olcObjectClasses: ( testObjectClass:1 NAME 'class1' DESC 'objectclass 1' SUP top STRUCTURAL MUST ( attr1 $ attr2 ) ) Running ldapmodify -x -W -D cn=admin,cn=config -f test.ldif -d 0 gives no output. -d 1 gives this: ldap_create ldap_sasl_bind ldap_send_initial_request ldap_new_connection 1 1 0 ldap_int_open_connection ldap_connect_to_host: TCP localhost:389 ldap_new_socket: 4 ldap_prepare_socket: 4 ldap_connect_to_host: Trying 127.0.0.1:389 ldap_pvt_connect: fd: 4 tm: -1 async: 0 ldap_open_defconn: successful ldap_send_server_request ber_scanf fmt ({it) ber: ber_scanf fmt ({i) ber: ber_flush2: 38 bytes to sd 4 ldap_result ld 0x7f2a8ccf3430 msgid 1 wait4msg ld 0x7f2a8ccf3430 msgid 1 (infinite timeout) wait4msg continue ld 0x7f2a8ccf3430 msgid 1 all 1 ** ld 0x7f2a8ccf3430 Connections: * host: localhost port: 389 (default) refcnt: 2 status: Connected last used: Mon Sep 10 11:29:57 2012 ** ld 0x7f2a8ccf3430 Outstanding Requests: * msgid 1, origid 1, status InProgress outstanding referrals 0, parent count 0 ld 0x7f2a8ccf3430 request count 1 (abandoned 0) ** ld 0x7f2a8ccf3430 Response Queue: Empty ld 0x7f2a8ccf3430 response count 0 ldap_chkResponseList ld 0x7f2a8ccf3430 msgid 1 all 1 ldap_chkResponseList returns ld 0x7f2a8ccf3430 NULL ldap_int_select read1msg: ld 0x7f2a8ccf3430 msgid 1 all 1 ber_get_next ber_get_next: tag 0x30 len 12 contents: read1msg: ld 0x7f2a8ccf3430 msgid 1 message type bind ber_scanf fmt ({eAA) ber: read1msg: ld 0x7f2a8ccf3430 0 new referrals read1msg: mark request completed, ld 0x7f2a8ccf3430 msgid 1 request done: ld 0x7f2a8ccf3430 msgid 1 res_errno: 0, res_error: <>, res_matched: <> ldap_free_request (origid 1, msgid 1) ldap_parse_result ber_scanf fmt ({iAA) ber: ber_scanf fmt (}) ber: ldap_msgfree ldap_free_connection 1 1 ldap_send_unbind ber_flush2: 7 bytes to sd 4 ldap_free_connection: actually freed So no real indication of an error. Where am I doing it wrong? Bonus question: If I have some entries of a certain objectclass, can I modify it (add/remove attributeTypes) without removing the entries? Thanks in advance for all help.

  Read the article

• Decyphering Seagate drive model numbers?

  - by Stefan Lasiewski

  I'm comparing Seagate's Enterprise and Desktop drives for a variety of old and new servers. These servers come from different generations, so options like size (73GB, 2TB) and interface (SATA vs SAS 3.0Gbps vs SAS 6Gbps vs SCSI Ultra320) are widely variable. I'm trying to compare the sizes, speeds and interfaces, but I'm getting thrown off by different models. Also, their website is not the best. Does anyone know of a documented explanation of the Seagate model numbers? And is there a single spreadsheet which compares the features for all drives (or all 'Enterprise' drives?). Seagate drives have model numbers like this: Model ST3600057SS 6-Gb/s SAS 600 GB None at Cheetah® 15K Hard Drives Model ST373455LW Ultra320 SCSI 73.4 GB 68-Pin LW at Cheetah® 15K Hard Drives Model ST32000644NS SATA 3Gb/s 2 TB None at Constellation™ ES Hard Drives Model ST973452SS 6-Gb/s SAS 73 GB None Savvio® 15K Hard Drives Model ST9200011FS SATA 3Gb/s 200 GB Pulsar™ Solid State Drives I understand the model numbers read something like this: ST - SOMETHING1 - SIZE - SOMETHING2 - INTERFACE Where the fields mean something like this: ST : For 'Seagate'? 'Seagate Technoligies'? SOMETHING1 - This field has number, but I'm not sure what that represents. SIZE - Size in Gigabytes. This is a number like '73' or '300' or '2000' SOMETHING2 - This field also has a number, but I'm not sure what it means. INTERFACE - This field seems to indicate the Interface. 'SS' means SAS, 'FC' means Fibre Channel, but I don't see how to distinguish between 6Gbps SAS and 3Gbps SAS, or different SATA or FC speeds. I don't see a field which indicates the RPM (15K , 10K, 7.2K) etc. Is this part of the model number?

  Read the article

• Resize a RAID 1 volume on OS X Snow Leopard - how? (Note: software raid)

  - by Emmel

  I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OS X 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

  Read the article

< Previous Page | 494 495 496 497 498 499 500 501 502 503 504 505  | Next Page >