Search Results

Search found 14975 results on 599 pages for 'os x'.

Page 501/599 | < Previous Page | 497 498 499 500 501 502 503 504 505 506 507 508  | Next Page >

• WD my cloud 4th is Super Slow

  - by Saduser

  I am using a WD my cloud 4Tb and I have read other posts about users complaining about getting only 10Mb per second. My problem is that I am getting about 100kb/s to transfer a 125gb iPhoto library. Estimated time is 11 days to transfer this file. This is unacceptable. On the back of the WD cloud I am getting a solid green light and from what I read this means that I am on a gigabyte network. I have mac book pro running Mac OS Mavericks. I have tried 4 different cables and turned off my router firewall. I don't run anti-virus nor any firewall on the mac. Other things I have checked: direct connection to both router and WD cloud device. Tried wireless but it is even slower. Previously I was able to transfer a 55Gb iPhoto library in 14 hours which I felt was acceptable. I figured it would take approximately double the time to transfer the 125gb file but 11 days is ridiculous. Any other suggestions? Anything else I can check (how to check it) what is the bottle neck?

  Read the article

• Can't install SB750 RAID drivers in Windows 7 for two additional storage drives

  - by jf46

  Mobo: ASUS M4A79XTD, 790X/SB750 OS: Windows 7 x64 I currently have SATA 1-4 set to RAID and SATA 5-6 set to IDE. I have an SSD connected to SATA5 with Windows 7 installed on it, and that works fine. I also have configured a RAID 1 array of two 1TB HDDs, connected to SATA 1 and 2. These don't show up in Windows, and I'm having trouble getting the RAID driver installed. I even tried booting from the Windows DVD and repairing or installing Windows, but when I navigated to the relevant .sys files on my motherboard's driver CD, Windows setup told me that the files in question weren't relevant to my hardware. To be clear: I'm not trying to install Windows on a RAID. I have Windows installed on a separate disk on a separate SATA controller. I just want to get the SB750 RAID drivers installed so that the Windows disk utility can see my RAID 1 array, which is composed of two other disks. Do I need to wipe my SSD and reinstall Windows to get the RAID driver installed? That seems kind of ridiculous, and given what I described above, I'm not even sure it would work. Any help or guidance would be appreciated - thanks! Edit: Also, I've copied the driver files from the mobo CD into system32 and rebooted, no luck. Then I changed HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\iaStorV\Start from 3 to 0, and that didn't work either.

  Read the article

• Burn bootable iso image to USB stick using dd: Won't boot (despite USB first in boot sequence)

  - by Nicolas Raoul

  I have installed Ubuntu on a Lenovo Thinkpad R500 2732, and I must update the BIOS. On the Lenovo website, I am offered this: BIOS Update Bootable CD for Windows 7 (32-bit, 64-bit), Vista (32-bit, 64-bit), XP - ThinkPad R500 I guess a bootable CD that would do a BIOS update is indeed what I need. (still wondering why it says "Windows" though... if it is bootable should not it be OS-agnostic?) Not wanting to waste a CD, I copied the image to my USB stick: sudo dd if=/home/nico/7yuj40uc.iso of=/dev/sdb1 bs=1M And rebooted, after making sure USB is first in the boot sequence. PROBLEM: It does not boot. Did I forget one step? Details about the iso image (readme): ls -lh 7yuj40uc.iso 25M file 7yuj40uc.iso /home/nico/7yuj40uc.iso: # ISO 9660 CD-ROM filesystem data '7YUJ40US ' (bootable) (Scroll to the right: it says "bootable") UNetbootin does not work because it is not a Linux image. Some people on the Internet advise to copy the content of the ISO and do other steps. This ISO has zero ISO content so it would not work. If I mount the ISO, I can see it contains zero files.

  Read the article

• Trying to build OpenSimulator.. nant fails

  - by Gary

  Output of nant is: Buildfile: file:///root/opensim-0.6.8-release/OpenSim.build Target framework: Mono 2.0 Profile Target(s) specified: build [echo] Using 'mono-2.0' Framework init: Debug: [echo] Platform unix build: [nant] /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/OpenSim.Framework.Servers.HttpServer.dll.build build Buildfile: file:///root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/OpenSim.Framework.Servers.HttpServer.dll.build Target framework: Mono 2.0 Profile Target(s) specified: build build: [echo] Build Directory is /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/bin/Debug [csc] Compiling 29 files to '/root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/bin/Debug/OpenSim.Framework.Servers.HttpServer.dll'. [csc] /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/AsynchronousRestObjectRequester.cs(103,41): error CS0246: The type or namespace name `TResponse' could not be found. Are you missing a using directive or an assembly reference? [csc] Compilation failed: 1 error(s), 0 warnings BUILD FAILED - 0 non-fatal error(s), 1 warning(s) /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/OpenSim.Framework.Servers.HttpServer.dll.build(14,6): External Program Failed: /usr/lib/pkgconfig/../../lib/mono/2.0/gmcs.exe (return code was 1) Total time: 1.2 seconds. BUILD FAILED Nested build failed. Refer to build log for exact reason. Total time: 1.3 seconds. OS is Fedora 7. Any ideas appreciated. :)

  Read the article

• Please advise on VPS config choice (with SQL Server Express)

  - by tjeuten

  Hi all, I might be interested in getting a VPS hosting plan for some small personal sites and .NET projects. Was thinking of Softsys Bronze Plan, as my current shared host plan is with them too. The stuff I want to host has grown beyond the capabilities of a Shared hosting plan, and I also want more control over the IIS/ASP.NET configuration, that's why I'm considering VPS. The main config details would be: Hyper-V 30 GB of diskspace 1 GB of RAM More info here: http://www.softsyshosting.com/Windows-VPS-HyperV.aspx Does anyone have experience with this plan (or something similar from another host), and maybe could answer these couple of questions: Bronze has a total diskspace of 30GB. Is the OS part of this quota or not ? If so, how much does a base configuration with Windows 2008 take up in diskspace ? Would you advise Windows 2008 R2 or Normal. Or would you advise to use Windows 2003 with this config. I'm planning on running a SQL Server Express install too. Would 1 GB of RAM be enough for both the Windows 2008 (R2) and SQL Express. The database load will not be that very high (a couple of 1000 records returned each day). The DB will most likely be far away from the 4GB limit, that's why I'd go for a SQL Express instead of paying extra licensing costs for a SQL Web install. But I'm more concerned about performance. Would you recommend Softsys as a VPS host ? I've been with them for one year for my Shared hosting plan, and have no complaints so far. Also, as I have no VPS experience, what are the pitfalls I need to be aware of, in terms of performance mainly, but maybe in other areas too ? Mathieu

  Read the article

• Request bursting from web application Load Tests

  - by MaseBase

  I'm migrating our web and database hosting to a new environment on all new machines. I've recently performed a Load Test using WAPT to generate load from multiple distributed clients. The server has plenty of room to handle the traffic load, but I'm seeing an odd pattern of incoming traffic during the load tests. Here is the gist of our setup: Firewall server running MS Forefront TMG 2010 on Win 2k8 server Request routing done by IIS Application Request Routing on firewall machine Web server is a Hyper-V VM on the Database server (which is the host OS) These machines are hefty with dual-CPU's with six cores (12 total procs) Web server running IIS 7.5 Web applications built in ASP.NET 2.0, with 1 ISAPI filter (Url Rewrite) in front What I'm seeing during the load tests is that the requests all come through in bursts. Even though I have 7 different distributed clients sending traffic loads, the requests come through about 300-500 requests at a time. The performance monitor shows nearly all of the counters moving through this pattern, where a burst of requests comes in the req/sec jumps to 70, the queued requests jumps to 500, the current requests jumps up, the CPU jumps up, everything. Then once it's handled that group of requests, it has a lull for nearly 10 seconds where nearly nothing is happening. 0-5 req/sec, 0 queued requests, minimal CPU usage. Then after 10 seconds of inactivity, another burst comes through, spiking all of the counters once again. What I can't figure out is why the requests are coming through in bursts when I know that the load being generated is not sent that way, especially considering the various load-generating clients sending traffic all in different intervals with random think time's between each request. Is there something in the layers between Hyper-V or perhaps in the hardware which might cause this coalesce of requests together? Here is what i'm looking at, the highlighted metric is Requests/sec, but the others critical counter go with it: Requests Queued (which I'd obviously like to keep as close to 0 as possible). Any ideas on this?

  Read the article

• Howto: SaaS / PHP Application / Tenants / Security

  - by Ben Fransen

  Hi all, Being completely new in the webhostingcorner I have a few questions on how to implement/setup a webserver for a SaaS application. I'm about to rent my own server for a new product (CMS) I'm launching in two months. Developing the system wasn't that much of wild ride to me, but a correct way to implement it, is. So lets say this is my situation: I want to host 10 websites for 8 clients. There are 6 single sites, and two clients have two websites they can manage with my software. The CMS must be placed on the server too, all clients are connecting to 1 system The database must be placed Depending on the contract a client makes, the client gets some storage. How to measure the used storage over the DB, FileSystem and email Clients may not, in any case be able to somehow get outside their directory, but from the CMS directory the CMS must be able to create files and dirs in a clients directory (for templates, imagegalleries, widgets, etc, etc). I was thinking about something like a dirstructure like this: ./CMS/ [all CMS files] ./Websites/*/ [all websites] My hostingprovider will install updates to the os (CentOS, latest) and the admin panel (Direct Admin). Is there anybody with experience on this topic? Or do you have some thoughts about it? please join the conversation since I'm completely new to this. Ben

  Read the article

• How can I fix Office Sharepoint Search service?

  - by unknown (yahoo)

  For some reason, in operations server services, Office Sharepoint Search Service is MISSING! Which means I cant get Shared services working, which in turn I cannot get, and I do not think I have ever got Usage and reporting to see who is visiting my website, counter and with what OS/ browser ETC. I dont think I have ever seen this work in the 2 years trying with sharepoint. So in essense I have two problems, most important SEARCH, second usage reports. When trying to search, all i get is unknown error. Nothing is in my event viewer at all. I have tried http://www.cjvandyk.com/blog/Lists/Posts/Post.aspx?ID=96 , in the comments on that site, on other person reports search is missing entirely and is going to uninstall. Im tired of uninstall sharepoint and resinstalling to fix an odd off issue. I have things setup with Team foundation server that took forever to get work and reinstallation is not my solution. As for usage reporting, this is what microsoft responds to the " Both Windows SharePoint Services Usage logging and Office SharePoint Usage Processing must be enabled to view usage reports. Please contact your administrator to ensure that these services are enabled. " error I cannot do all the steps since SSP needs to be setup which i cant above.

  Read the article

• Disk IO slow on ESXi, even slower on a VM (freeNAS + iSCSI)

  - by varesa

  I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas 8.0.4). Those two machines are connected to each other with Gigabit ethernet. The raid-z volume is divided into three parts: two zvols, shared with iscsi, and one directly on top of zfs, shared with nfs and similar. I ssh'd into the freeNAS box, and did some testing on the disks. I used ddto test the third part of the disks (straight on top of ZFS). I copied a 4GB (2x the amount of RAM) block from /dev/zero to the disk, and the speed was 80MB/s. Other of the iSCSI shared zvols is a datastore for the ESXi. I did similar test with time dd .. there. Since the dd there did not give the speed, I divided the amount of data transfered by the time show by time. The result was around 30-40 MB/s. Thats about half of the speed from the freeNAS host! Then I tested the IO on a VM running on the same ESXi host. The VM was a light CentOS 6.0 machine, which was not really doing anything else at that time. There were no other VMs running on the server at the time, and the other two "parts" of the disk array were not used. A similar dd test gave me result of about 15-20 MB/s. That is again about half of the result on a lower level! Of course the is some overhead in raid-z - zfs - zvolume - iSCSI - VMFS - VM, but I don't expect it to be that big. I belive there must be something wrong in my system. I have heard about bad performance of freeNAS's iSCSI, is that it? I have not managed to get any other "big" SAN OS to run on the box (NexentaSTOR, openfiler). Can you see any obvious problems with my setup?

  Read the article

• 32 core (each physical core) 2.2 GhZ or 12 core (6 physical cores) 3.0GHZ?

  - by Tejaswi Rana

  I am working on a multithreaded application (Forex trading app built on C#) and had the client upgrade from the 12 core 3.0GHZ machine (Intel) to a 32 core 2.2 Ghz machine (AMD). The PassMark benchmark results were significantly higher when using multicores doing Integer, Floating and other calculations while for a single core calculation it was a bit slower than the pack (others that were being compared to with similar config as the 12 core one). Oh it also comes with 64 GB RAM (4 times as the other one) and a much faster SSD. So after configuring and running the application on that machine, not only did it not perform as well, it was significantly slower. We're talking about 30seconds - 1 minute slower on an app that usually completes processing within 5-20 secs. The application uses MAX DEGREE of PARALLELISM (TPL) which I've tried setting to number of cores and also half of that. I've also tried running single threaded and without setting any limits in parallel threading. While it may be the hardware has some issues, I am wondering if the CPU processing speed is the issue. I can overclock to 3.0 GHZ. But is that even a good idea? Server Info - AMD http://www.passmark.com/forum/showthread.php?4013-AMD-Dual-6272-performance-is-60-lower-than-benchmarks Seems that benchmark was wrong to start with - officially. Intel i7 3930k OS (same in both) Windows 7 Professional 64-bit

  Read the article

• OpenVPN Client timing out

  - by Austin

  I recently installed OpenVPN on my Ubuntu VPS. Whenenver I try to connect to it, I can establish a connection just fine. However, everything I try to connect to times out. If I try to ping something, it will resolve the IP, but will time out after resolving the IP. (So DNS Server seems to be working correctly) My server.conf has this relevant information (At least I think it's relevant. I'm not sure if you need more or not) # Which local IP address should OpenVPN # listen on? (optional) ;local a.b.c.d # Which TCP/UDP port should OpenVPN listen on? # If you want to run multiple OpenVPN instances # on the same machine, use a different port # number for each one. You will need to # open up this port on your firewall. port 1194 # TCP or UDP server? ;proto tcp proto udp # "dev tun" will create a routed IP tunnel, # "dev tap" will create an ethernet tunnel. # Use "dev tap0" if you are ethernet bridging # and have precreated a tap0 virtual interface # and bridged it with your ethernet interface. # If you want to control access policies # over the VPN, you must create firewall # rules for the the TUN/TAP interface. # On non-Windows systems, you can give # an explicit unit number, such as tun0. # On Windows, use "dev-node" for this. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel if you # have more than one. On XP SP2 or higher, # you may need to selectively disable the # Windows firewall for the TAP adapter. # Non-Windows systems usually don't need this. ;dev-node MyTap # SSL/TLS root certificate (ca), certificate # (cert), and private key (key). Each client # and the server must have their own cert and # key file. The server and all clients will # use the same ca file. # # See the "easy-rsa" directory for a series # of scripts for generating RSA certificates # and private keys. Remember to use # a unique Common Name for the server # and each of the client certificates. # # Any X509 key management system can be used. # OpenVPN can also use a PKCS #12 formatted key file # (see "pkcs12" directive in man page). ca ca.crt cert server.crt key server.key # This file should be kept secret # Diffie hellman parameters. # Generate your own with: # openssl dhparam -out dh1024.pem 1024 # Substitute 2048 for 1024 if you are using # 2048 bit keys. dh dh1024.pem # Configure server mode and supply a VPN subnet # for OpenVPN to draw client addresses from. # The server will take 10.8.0.1 for itself, # the rest will be made available to clients. # Each client will be able to reach the server # on 10.8.0.1. Comment this line out if you are # ethernet bridging. See the man page for more info. server 10.8.0.0 255.255.255.0 # Maintain a record of client <-> virtual IP address # associations in this file. If OpenVPN goes down or # is restarted, reconnecting clients can be assigned # the same virtual IP address from the pool that was # previously assigned. ifconfig-pool-persist ipp.txt # Configure server mode for ethernet bridging. # You must first use your OS's bridging capability # to bridge the TAP interface with the ethernet # NIC interface. Then you must manually set the # IP/netmask on the bridge interface, here we # assume 10.8.0.4/255.255.255.0. Finally we # must set aside an IP range in this subnet # (start=10.8.0.50 end=10.8.0.100) to allocate # to connecting clients. Leave this line commented # out unless you are ethernet bridging. ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 # Configure server mode for ethernet bridging # using a DHCP-proxy, where clients talk # to the OpenVPN server-side DHCP server # to receive their IP address allocation # and DNS server addresses. You must first use # your OS's bridging capability to bridge the TAP # interface with the ethernet NIC interface. # Note: this mode only works on clients (such as # Windows), where the client-side TAP adapter is # bound to a DHCP client. ;server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. ;push "route 192.168.10.0 255.255.255.0" ;push "route 192.168.20.0 255.255.255.0" # To assign specific IP addresses to specific # clients or if a connecting client has a private # subnet behind it that should also have VPN access, # use the subdirectory "ccd" for client-specific # configuration files (see man page for more info). # EXAMPLE: Suppose the client # having the certificate common name "Thelonious" # also has a small subnet behind his connecting # machine, such as 192.168.40.128/255.255.255.248. # First, uncomment out these lines: ;client-config-dir ccd ;route 192.168.40.128 255.255.255.248 # Then create a file ccd/Thelonious with this line: # iroute 192.168.40.128 255.255.255.248 # This will allow Thelonious' private subnet to # access the VPN. This example will only work # if you are routing, not bridging, i.e. you are # using "dev tun" and "server" directives. # EXAMPLE: Suppose you want to give # Thelonious a fixed VPN IP address of 10.9.0.1. # First uncomment out these lines: ;client-config-dir ccd ;route 10.9.0.0 255.255.255.252 # Then add this line to ccd/Thelonious: # ifconfig-push 10.9.0.1 10.9.0.2 # Suppose that you want to enable different # firewall access policies for different groups # of clients. There are two methods: # (1) Run multiple OpenVPN daemons, one for each # group, and firewall the TUN/TAP interface # for each group/daemon appropriately. # (2) (Advanced) Create a script to dynamically # modify the firewall in response to access # from different clients. See man # page for more info on learn-address script. ;learn-address ./script # If enabled, this directive will configure # all clients to redirect their default # network gateway through the VPN, causing # all IP traffic such as web browsing and # and DNS lookups to go through the VPN # (The OpenVPN server machine may need to NAT # or bridge the TUN/TAP interface to the internet # in order for this to work properly). push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" # Certain Windows-specific network settings # can be pushed to clients, such as DNS # or WINS server addresses. CAVEAT: # http://openvpn.net/faq.html#dhcpcaveats # The addresses below refer to the public # DNS servers provided by opendns.com. ;push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" # Uncomment this directive to allow different # clients to be able to "see" each other. # By default, clients will only see the server. # To force clients to only see the server, you # will also need to appropriately firewall the # server's TUN/TAP interface. ;client-to-client # Uncomment this directive if multiple clients # might connect with the same certificate/key # files or common names. This is recommended # only for testing purposes. For production use, # each client should have its own certificate/key # pair. # # IF YOU HAVE NOT GENERATED INDIVIDUAL # CERTIFICATE/KEY PAIRS FOR EACH CLIENT, # EACH HAVING ITS OWN UNIQUE "COMMON NAME", # UNCOMMENT THIS LINE OUT. ;duplicate-cn # The keepalive directive causes ping-like # messages to be sent back and forth over # the link so that each side knows when # the other side has gone down. # Ping every 10 seconds, assume that remote # peer is down if no ping received during # a 120 second time period. keepalive 10 120 # For extra security beyond that provided # by SSL/TLS, create an "HMAC firewall" # to help block DoS attacks and UDP port flooding. # # Generate with: # openvpn --genkey --secret ta.key # # The server and each client must have # a copy of this key. # The second parameter should be '0' # on the server and '1' on the clients. ;tls-auth ta.key 0 # This file is secret # Select a cryptographic cipher. # This config item must be copied to # the client config file as well. ;cipher BF-CBC # Blowfish (default) ;cipher AES-128-CBC # AES ;cipher DES-EDE3-CBC # Triple-DES # Enable compression on the VPN link. # If you enable it here, you must also # enable it in the client config file. comp-lzo # The maximum number of concurrently connected # clients we want to allow. ;max-clients 100 # It's a good idea to reduce the OpenVPN # daemon's privileges after initialization. # # You can uncomment this out on # non-Windows systems. ;user nobody ;group nogroup # The persist options will try to avoid # accessing certain resources on restart # that may no longer be accessible because # of the privilege downgrade. persist-key persist-tun # Output a short status file showing # current connections, truncated # and rewritten every minute. status openvpn-status.log # By default, log messages will go to the syslog (or # on Windows, if running as a service, they will go to # the "\Program Files\OpenVPN\log" directory). # Use log or log-append to override this default. # "log" will truncate the log file on OpenVPN startup, # while "log-append" will append to it. Use one # or the other (but not both). ;log openvpn.log ;log-append openvpn.log # Set the appropriate level of log # file verbosity. # # 0 is silent, except for fatal errors # 4 is reasonable for general usage # 5 and 6 can help to debug connection problems # 9 is extremely verbose verb 3 # Silence repeating messages. At most 20 # sequential messages of the same message # category will be output to the log. ;mute 20 I've tried on multiple computers by the way. The same result on all of them. What could be wrong? Thanks in advance, and if you need other information I'll gladly post it. Information for new comments root@vps:~# iptables -L -n -v Chain INPUT (policy ACCEPT 862K packets, 51M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 3 packets, 382 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 4641 298K ACCEPT all -- * * 10.8.0.0/24 0.0.0.0/0 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT 1671K packets, 2378M bytes) pkts bytes target prot opt in out source destination And root@vps:~# iptables -t nat -L -n -v Chain PREROUTING (policy ACCEPT 17937 packets, 2013K bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 8975 packets, 562K bytes) pkts bytes target prot opt in out source destination 1579 103K SNAT all -- * * 10.8.0.0/24 0.0.0.0/0 to:SERVERIP Chain OUTPUT (policy ACCEPT 8972 packets, 562K bytes) pkts bytes target prot opt in out source destination

  Read the article

• MySQL Server Is Slow

  - by user2853965746

  I have two MySQL servers and one was just recently setup. The one I just recently setup is a bit slower than my older one, which kind of bothers me because I don't want my clients to be upset with the speed difference when I launch the new one. The older server runs on Ubuntu (~13.04 I believe) and the new one is on Debian 6. Both servers are 2GB ram, but my newer server is has an SSD, so I thought it might be the same speed if not faster. Anyway, the speed difference isn't too much (both are still under a second, but still noticeable). Whenever I select 50 rows from the user table on my older server (SELECT * FROM users LIMIT 50), I get the results in 0.003 s. There is 100,000+ accounts in that table. Whenever running the same command on the same table with only six dev accounts, it takes 0.069 s. It may not seem like a lot, but it's noticeable when you're used to a fast response. I added skip-name-resolve to the config and it didn't seem to help. Basically I'm asking if anyone knows what can cause a MySQL server to be slow in Debian 6? Should I just drop it and switch to Ubuntu like the older server (I don't think the OS is the problem, but you never know)? The older server is under a lot of use too, it's used a lot for web api's on my website. A lot of connections and stuff, and it still remains fast.

  Read the article

• Can access SSH but can't access cPanel web server

  - by Tom

  I've built a Cent OS 6.0 vps and then i've installed the latest cPanel/WHM. This isn't my first installation but i've noticed something weird especially that i've never used the 6.0 version.. when i tried to install cPanel, it didn't recognize wget so installed it, then cPanel said that Perl isn't installed, i've installed that and the installation went well since then. Now, when i've tried to access the server via the browser with the IP Adress as i've used to, it didn't work, it was just loading forever, i tried the 2087 port, still the same. but SSH works. I've also tried the commands to start the server manually but none of them worked. How to fix that? Edit: iptables -nL Result root@server [~]# iptables -nL Chain INPUT (policy ACCEPT) target prot opt source destination acctboth all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT) target prot opt source destination acctboth all -- 0.0.0.0/0 0.0.0.0/0 Chain acctboth (2 references) target prot opt source destination tcp -- 216.119.149.168 0.0.0.0/0 tcp dpt:80 tcp -- 0.0.0.0/0 216.119.149.168 tcp spt:80 tcp -- 216.119.149.168 0.0.0.0/0 tcp dpt:25 tcp -- 0.0.0.0/0 216.119.149.168 tcp spt:25 tcp -- 216.119.149.168 0.0.0.0/0 tcp dpt:110 tcp -- 0.0.0.0/0 216.119.149.168 tcp spt:110 icmp -- 216.119.149.168 0.0.0.0/0 icmp -- 0.0.0.0/0 216.119.149.168 tcp -- 216.119.149.168 0.0.0.0/0 tcp -- 0.0.0.0/0 216.119.149.168 udp -- 216.119.149.168 0.0.0.0/0 udp -- 0.0.0.0/0 216.119.149.168 all -- 216.119.149.168 0.0.0.0/0 all -- 0.0.0.0/0 216.119.149.168 all -- 0.0.0.0/0 0.0.0.0/0

  Read the article

• restoring a failed SBS 2000 box...

  - by Brad Pears

  Hi there, I read a post where you had mentioned you have had a PERC card blow up on you in an SBS box... I've got a similar situation where one of my RAID drives failed and then the power supply failed before I could replace the drive... I then replaced the power supply and the failed drive and reconfigured the RAID array. I had a recent full backup of the my Win2k SBS's C: drive stored on my SYmantec backup exec server so I installed win2K server on the c: partition and then once I had that up and running, installed the backup exec agent so as to do a restore of the entire c drive including system state. THis all worked just fine, until I had to reboot. I received an "incorrect drive configuration" error and then it hangs. I figure that likely makes sense becasue I think my RAID array is configured slightly different now in that the partitions may be sizeded ever so slightly differently now than they were before I think... Is there a way I can just restore from my backup BUT maybe exclude some of the registry and hidden boot files it wants to restore so that it is booting with the current configuration now active on that machine - not the pre blow up configuration files? I also read a post that indicated you might have to install the exact same service pack etc... etc.. before attemting a restore but that does not make sense to me being as the entire c drive contents are going to be overwritten by the restore anyway? THe basic OS install is just to be able to get the backup exec agent installed . I can;t understand why one would need to install the exact same SP level. CAn you shed some light on what I might be able to do to get this thing up and running? Thanks,Brad

  Read the article

• Windows XP Language, explorer.exe

  - by nmuntz

  Hi, I was given by my company a laptop with Windows XP Professional in Spanish. I would like to translate it to English, since I really DISLIKE to use localized versions of programs. I have read about Windows MUI packs, however you MUST have Windows XP Pro in English in order to translate it to other language, you can't translate it TO English from other language. Since reinstalling the OS using a Win XP CD in english is not an option (don't have the license nor the CD, and don't have domain privileges to rejoin my computer to the domain), I was wondering what are the essential files that contain localized strings of text. I was doing some research, and apparently explorer.exe has many of the Windows Error Messages and other strings. Will replacing my original explorer.exe with one from Windows XP in English be enough (and work) for having a "basic" english version of windows? Im mainly interested in having error messages, start menu, and the control panel in english. Also, does it HAVE to be the same version as the Service Pack im running? Besides explorer.exe are there any other essential files that i should try to get and replace? Do you see any "dangers" in replacing this files with english version ones? Thanks in advance for your help.

  Read the article

• Windows 7 Can't Connect to Network Drive on Windows XP

  - by Alex Yan

  I have a Windows XP desktop and a Windows 7 laptop both connected to a TrendNET TEW-432BRP router, which is connected to the Internet. They both have static IPs. The desktop has an external hard drive connected to it. The laptop is wireless and the desktop is wired. I enabled sharing on the external hard drive about two years ago when I bought it. I mapped it as a network drive on the laptop. I think it was yesterday, the laptop just stopped recognizing any of the computers on my network (When I open network, my laptop's the only one on it). I also get an error message "An error occurred while connecting A: to \CERTIFIED-DATA\Expansion Microsoft Windows Network: The network path was not found. The connection has not been restored" when I try to connect to the network drive. Both computers run Avast, and there hasn't been any problems with it. This has happened before but I never figured out why and how to fix it. It's usually fixed when I reinstall the OS of the affected system. Edit: I can't navigate the computer using \\CERTIFIED-DATA. I get a message saying "Windows cannot access \CERTIFIED-DATA. Check the spelling of the name, Otherwise, there might be a problem with your network" I clicked diagnose on the message and it failed to find anything wrong I clicked diagnose on my wireless connection, and it just keeps trying to check if something is wrong with the connection I can ping it successfully

  Read the article

• Linking to a chat room via XMPP: URI

  - by Coderer

  I found out how to link directly to a chat room on a Jabber conference server -- it took a bit of digging, and I wound up actually looking at the spec before I was sure I was doing it right. I confirmed here, so I'm pretty sure I've got it. The results, though, are puzzling. If I click a link of the style xmpp:[email protected] I get a new chat session with user "dude" at example.com, as expected. If I tack on a nonsense query (xmpp:[email protected]?foobar), it's ignored, which is what the spec says should happen. However, if I use xmpp:[email protected]?join, as in the link above, nothing happens. I dug a little deeper, and found out that on my (Linux) system, xmpp URIs are handled via purple-url-handler, so I dropped to a terminal and ran it manually. The result was that any xmpp URI ran fine except one that includes a ?join query. The ?join query results in a dbus crash, pointing specifically to line 2356 of dbus-message.c -- a little Googling suggests this probably is dbus's less-than-elegant way of telling me that somebody is using dbus incorrectly. Am I crafting my link correctly? Is this an OS or maybe application issue? Does this work on other platforms / browsers / etc? More importantly, is there any easy way to fix it?

  Read the article

• Windows Bluescreen - atikmpag.sys

  - by Mochan

  Information Name: atikmpag.sys bluescreen (BSOD or BlueScreen of Death) Error code: 0x00000116 Appears when: Playing games, watching videos Can be reproduced: Yes Cause: Graphics Card is the main assumption System Specifications Before we begin - I will inform you of my specifications. OS: Windows 7 x64 Home Edition Model: Dell Inspiron 15R Special Edition (aka Inspiron 7520) (Add 2GB of RAM to the model linked) Hard Drive: 1TB CPU: Intel Quad-Core i7 Sandy Bridge (I think) Processor at 2.10GHz (I think it can be clocked to 3GHz?) RAM: 6GB (I think 1 x 4GB and 1 x 2GB) Display: 15.6" HD (1366x768) Graphics: AMD Radeon HD 7500M 2GB Details So now that you know some basics about my computer, I'll get to the problem. Being an Ubuntu user I hardly use Windows, but occasionally I do. Like to run Skyrim and other games incompatible with Linux and WINE. The new Sims 3 Seasons patch is also now not supported. When playing these two games and other ones, theoretically. I have also heard others saying that while watching HD movies and video series it also happens. While watching the bluescreen as it happens, I see it is the 'atikmpag.sys' error. I have not installed much and nothing significant. I think I have downloaded Skyrim, Firefox and The Sims 3. I haven't done much more... since Ubuntu is definitely the best in comparison! (No hate, just a joke :P). I can reproduce it easily (just by running a game for less than a minute). It is always there each time, but it's never at a specific time or anything. So far I have found that it may be caused by lack of power to the graphics card, or it may be damaged or fried. Since I've had the computer for a mere 4 months (and have had other problems with it also). I have contacted Dell but they are useless beyond belief. Anyone with any information, solutions or details are encouraged to share your knowledge, as it would be immensely appreciated.

  Read the article

• Macbook Pro won't boot from DVD with SSD

  - by Adam Carr

  Here's the timeline of events. Had a running MBP 17 Early 2011 Thunderbolt with OWC Mercury Extreme Pro SSD 115GB drive. Installed Windows 7 via bootcamp. I have done this multiple times before and every time I need to format the bootcamp partition before installing. I think this time I actually deleted the partition and then selected the freespace to install. This worked fine for the most part but I wasn't able to boot the boot camp partition using vmware fusion. I gave up and used the boot camp assistant to revert back to one mac partition. I was getting some odd behavior so I rebooted the machine. It then came up with a message saying no bootable partiton. This made me think (and still does) that the windows install using the free space versus the boot camp partition caused the windows MBR boot loader to get installed incorrectly and mucked up the OS X installation. Ok, fine, I can just reinstall. I can't seem to boot from the original MBP installation DVD. I hold down c on boot but I never get past the all grey screen. I hear the DVD drive spin up but it eventually stops. I put the original HD back in it and everything works fine but when I put the SSD in, I can't boot from the DVD drive. I have already set up an RMA with OWC to send back the drive but considering the order of events, I feel as though it isn't a hardware issue but can't seem to figure out how to fix it. I can always send it back in but figured I would check and see if anyone could offer some guideance/assistence before doing so.

  Read the article

• .NET 3.5 installation comes up with Error 0x800F0906, then 0x800F0081F using dism

  - by Austin Meadows

  I've recently tried installing .NET 3.5 for an application on Windows 8.1. I used the OS's popup thing to download/install .NET 3.5 and always get error code 0x800F0906. Upon further research, I found I would have to pop in my Windows 8 CD and install it with this command, where "E:\" is where my CD is mounted: Dism /online /enable-feature /featurename:NetFx3 /All /Source:E:\sources\sxs /LimitAccess This and any derivative of it (e.g., removing /LimitAccess) has not worked for me and has either given me the same error code (0x800F0906) or a different one, 0x800F0081F. I've even copied the sxs folder to my hard drive, just in case something was going on with the CD Drive, only to have the same results. In that case, I used this command line: Dism /online /enable-feature /featurename:NetFx3 /All /Source:C:\dotnet35 /LimitAccess I find this surreal because in both cases, the files are indeed there but the program thinks it's not. Here's the CBS.log file. Any ideas on how to fix this? Any help is very appreciated :) EDIT: I now have a proper dism.log file, I'm not sure what happened to the last one or why it did that. Here's the link to the new log file. It's interesting to note that it doesn't recognize some of the commands in the script such as "featurename" or "source".

  Read the article

• Portable USB drives hidden pertition - New request

  - by ZXC

  This question was made by Francesco on Jul 29 '11 at 17:14. and the replies were not satisfactory due they not point to an important problem that´s: Why could anyone want to make certain data only accesible for a program but not to the users?. For example: If I want to do a safe distribution of original music for demostration purposes I will need several requisites: 1) The music should be heard using a simple procedure like selecting the name of each song on a playlist of a mediaplayer. 2) The portable media, ussually a portable USB drive, must hide for complete and should make unaccesible the files that contain the audio data to anything but the mediaplayer, that must be in the first partition, the one that is visible. 3) Considering that´s impossible to really hide files in a non-hidden partition, a second hidden partition should be created in the USB drive and the audio data will be stored there. 4) The trick is to read the audio data files stored in the hidden partition with a mediaplayer stored in the visible partition, the media player also should be a complete standalone program and independent from any library of the operating system except of the OS audio system. 5) The hidden partition should have a copy protection scheme that could impede to do copies of the data or create working ISO images of it. I know that this description could not be technically accurate but it has a complete logic from the needs of a music producer against the problem of piracy. The philosophy that surrounds the concept is to transform a virtual object like a digital string of audio in a solid object like the analog vinyl discs are.

  Read the article

• Why does USB thumb drive screw up boot sequence?

  - by Carl B

  I am looking for understanding to a boot issue. I have at times had some files and such that I save and retrieve from my thumb drive. I use the front panel as it is nice and easy to get to and I typically power down my system nightly. If I forget to pull the drive and power on the system, it becomes the first bootable device. As there is no OS on the USB Drive I get the BOOTMGR is missing press CTRL+ALT+DELETE. When I go into BIOS to see Boot sequence, there’s the thumb drive up top, DVD drive is missing and not found in the list of devices. All of the hard drives are next in line. When I pull the USB drive, and reboot, everything is back to normal. Old boot sequence is in place, DVD drive right where it should be and no issues. So why does this happen with a USB drive in port at boot up? If it can’t be booted from, shouldn’t the next drive be attempted? Note: This happens when the thumb drive is plugged into a USB port on the front panel. It does not seem to happen on rear panel ports.

  Read the article

• No digital audio output with Asus Xonar DG

  - by Lunatik

  I've purchased an Asus Xonar DG as replacement for faulty onboard audio in a Medion 8822 as it has an optical output which is all I really need to feed my HTPC. I uninstalled the previous drivers/devices, switched the PC off, inserted the Asus card, powered up, disabled the onboard audio in the BIOS, then installed the driver that came on the CD (same version as on Asus' website as of today) and everything went perfectly - no errors. I set the audio devices up in Windows and in the Asus utility (SPDIF enabled, 6-ch audio) as I would expect to see them work, but the only thing is I have no digital audio from test tones within Windows/the Asus utility, PCM audio or Dolby Digital from DVD. Analogue audio is fine. I've uninstalled things and reinstalled a couple of times now, as well as trying almost all combinations of analogue/digital outputs but can't get it sorted. Does anyone have any tips on how to get this working? This card has just been released so there isn't much out there to go on. Notes: The light on the toslink port is lit. OS is Vista 32-bit SP2 and all up to date, pretty much a fresh install with almost no 3rd party applications installed This page seems to suggest that a digital output device in Windows is not needed with Xonar cards as it was with the previous Realtek so I have it set to Analog. The only other output device is S/PDIF pass-thru

  Read the article

• Can't mount FAT32 drive under Ubuntu Linux

  - by Josh

  I have a 320GB USB drive with a single large FAT32 partition. The volume mounts perfectly fine on my Mac OS X 10.5.8 machine and Disk Utility on the mac reports no issues with the volume. I can read/write all data on the drive. However when I connect the drive to my Ubuntu 9.10 Karmic system, the partition does not mount. dmesg|tail says: [ 2752.334822] scsi3 : SCSI emulation for USB Mass Storage devices [ 2752.335040] usb-storage: device found at 3 [ 2752.335044] usb-storage: waiting for device to settle before scanning [ 2757.330301] usb-storage: device scan complete [ 2757.331005] scsi 3:0:0:0: Direct-Access WD 3200AAK External 1.65 PQ: 0 ANSI: 0 [ 2757.331772] sd 3:0:0:0: Attached scsi generic sg2 type 0 [ 2757.355647] sd 3:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 2757.360737] sd 3:0:0:0: [sdb] Write Protect is off [ 2757.360749] sd 3:0:0:0: [sdb] Mode Sense: 00 00 00 00 [ 2757.360755] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367618] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367631] sdb: sdb1 [ 2762.797622] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2762.797636] sd 3:0:0:0: [sdb] Attached SCSI disk [ 2822.866228] FAT: bogus number of reserved sectors [ 2822.866237] VFS: Can't find a valid FAT filesystem on dev sdb1. When I run fsck.vfat -a /dev/sdb1 I get: root@cartman:~# fsck.vfat -a /dev/sdb1 dosfsck 3.0.3, 18 May 2009, FAT32, LFN Logical sector size is zero. Googling "vfat Logical sector size is zero" produced no consensus as to the solution. I would prefer not to have to completely reformat the disk if possible because it contains about 280GB of data I would rather not have to find a temporary home for. Any suggestions?

  Read the article

• How do I get the F1-F12 keys to switch screens in gnu screen in cygwin when connecting via SSH?

  - by Mikey

  I'm connecting to a desktop running cygwin via SSH from the terminal app in Mac OS X. I have already started screen on the cygwin side and can connect to it over the SSH session. Furthermore, I have the following in the .screenrc file: bindkey -k k1 select 1 # F1 = screen 1 bindkey -k k2 select 2 # F2 = screen 2 bindkey -k k3 select 3 # F3 = screen 3 bindkey -k k4 select 4 # F4 = screen 4 bindkey -k k5 select 5 # F5 = screen 5 bindkey -k k6 select 6 # F6 = screen 6 bindkey -k k7 select 7 # F7 = screen 7 bindkey -k k8 select 8 # F8 = screen 8 bindkey -k k9 select 9 # F9 = screen 9 bindkey -k F1 prev # F11 = prev bindkey -k F2 next # F12 = next However, when I start multiple windows in screen and attempt to switch between them via the function keys, all I get is a beep. I have tried various settings for $TERM (e.g. ansi, cygwin, xterm-color, vt100) and they don't really seem to affect anything. I have verified that the terminal app is in fact sending the escape sequence for the function key that I'm expecting and that my bash shell (running inside screen) is receiving it. For example, for F1, it sends the following (hexdump is a perl script I wrote that takes STDIN in binmode and outputs it as a hexadecimal/ascii dump): % hexdump [press F1 and then hit ^D to terminate input] 00000000: 1b4f50 .OP If things were working correctly, I don't think bash should receive the escape sequence because screen should have caught it and turned it into a command. How do I get the function keys to work?

  Read the article

< Previous Page | 497 498 499 500 501 502 503 504 505 506 507 508  | Next Page >