Search Results

Search found 13909 results on 557 pages for 'old man'.

Page 502/557 | < Previous Page | 498 499 500 501 502 503 504 505 506 507 508 509  | Next Page >

  • Configuring VLAN's on two HP procurve switches

    - by pan
    Trying to route a new ISP (Microwave link) from one of my out buildings to my computer room and hence my firewall. Old ISP came direct into firewall. In the outbuilding the Microwave modem connects with cat5 to HP Procurve 2524 switch. Because this ISP is coming through my internal network, I plan on using a new vlan called "airspeed" only for this ISP traffic. Up until now I've just been using the Default_vlan on both HP switches (4108 + 2524). So far I've been unable to ping from my laptop to the ISP modem both of which are on the new vlan 2 ("Airspeed"). No traffic needs to cross from vlan 2 to vlan 1 so I've left the ports as untagged. I've used the subnet provide from my ISP as the new vlan 2 subnet. Can anybody see what I'm doing wrong here? I've added the configuration of both switch below. Rough diagram: Microwave modem (Gateway IP 77.75.00.49) | HP 2524 switch (port 24) | HP 2524 switch fibre link | HP 4108GL switch fibre link | HP 4108GL switch (port D1) | Laptop configured with IP 77.75.00.50 (for testing but will be connected to firewall) And my 4108GL config: ; J4865A Configuration Editor; Created on release #G.07.21 hostname "HP ProCurve Switch 4108GL" cdp run module 1 type J4864A module 2 type J4862B module 3 type J4862B module 4 type J4862B ip default-gateway 128.1.146.50 snmp-server community "public" Unrestricted snmp-server host 128.1.146.51 "public" Not-INFO snmp-server host 128.1.146.38 "public" vlan 1 name "DEFAULT_VLAN" untagged A1-A3,B1-B24,C1-C24,D2-D24 ip address 128.1.146.203 255.255.0.0 no untagged D1 exit vlan 2 name "Airspeed" untagged D1 ip address 77.75.00.51 255.255.255.248 exit Finally my 2524 config: ; J4813A Configuration Editor; Created on release #F.04.08 hostname "HP ProCurve Switch 2524" cdp run ip default-gateway 0.0.0.0 snmp-server community "public" Unrestricted snmp-server host 128.1.146.51 "public" Not-INFO snmp-server host 128.1.146.51 "public" snmp-server host 128.1.146.38 "public" vlan 1 name "DEFAULT_VLAN" untagged 1-23,25-26 no untagged 24 ip address 128.1.146.204 255.255.0.0 exit vlan 2 name "Airspeed" untagged 24 ip address 77.75.00.51 255.255.255.248 exit no aaa port-access authenticator active

    Read the article

  • Windows 7 + Deep Freeze - I'm stuck in an endless reboot loop

    - by myermian
    I have the following setup: Windows 7 Ultimate Deep Freeze I "thawed" my machine last night and performed a Windows Update. The update is having issues (it gets stuck at 32%, fails, and restarts my machine). When it reboots it attempts it again, and again, and again, etc. (Endless loop). I looked online and found some solutions, but none of them seem to be working: When I run Safe Mode, Safe Mode w/ Network, or Safe Mode w/ Command Prompt it attempts to revert the Windows Update changes. However, the problem is with Deep Freeze on (and now in "Frozen" mode) the reverted changes don't stay, and I'm back into the loop of death. Oh, and side note: "Safe Mode w/ Command Prompt" does not actually take me to a command prompt window? Perhaps because it is attempting to complete the Windows Update changes first? I have tried to select the option to NOT restart when an windows error occurs, but it still does. I tried the remainder of all the other options in the F8 screen. The only other option left is to find my Windows 7 Media Disc (I can't find it right now) and use it to repair windows (because for some reason the repair option does not show up in the F8 screen). Is there a way to disable Deep Freeze from loading? When I selected "Safe Mode w/ Command Prompt" I noticed that it loads the DpFrz.sys file. I know that when I'm in the Windows Boot Manager if I press F10 instead of F8 (while highlighting Windows 7) it takes me to an "Edit Boot Options" screen: Edit Windows boot options for: Windows 7 Path: \Windows\system32\winload.exe Partition: 2 Hard Disk: 8e90e329 [ /NOEXECUTE=OPTIN (I CAN EDIT THIS LINE) ] Update: I found my Windows 7 Media Disk and it did not help out. The laptop had the "System Restore" as a partition on the HDD. I later received (in the mail) a Windows 7 Upgrade Disc from Sony to upgrade my system from Windows Vista to Windows 7 Ultimate. I placed the disc into the DVD drive and it does not come up as a "bootable" disc. I'm going to try to find an alternative disc to see if I can get into Command Prompt. Update 2: I got a Windows Repair disc and got into a command prompt window. I got into the registry and disabled Deep Freeze. Also: I renamed the Pending.xml file to Pending.old I cleared out the Windows Temp directory I still am stuck in the loop (though, it isn't an issue with DeepFreeze anymore because I can make changes to the hard drive and they persist). Not sure what to do at this point? Update 3: I ran the repair option and it couldn't repair, but it did point me to something. It says the error was due to a driver that was failing. I have a feeling it is my UPEK Fingerprint scanner.

    Read the article

  • Graphics driver for ubuntu on dell latitude XT

    - by marc.riera
    Hi, we have a laptop (dell latitude xt) on our company, and we would like to install ubuntu on it. windows 7 works fine out of the box, so the hardware is fine. since this laptop has a touchscreen we just installed ubuntu 10.10 netbook edition 32x. But, we do not manage to enable the touchscreen, neither the vga graphic drivers. this is the output from lspci, if somebody cares. 00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 7930 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS7932 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc Device 7934 00:06.0 PCI bridge: ATI Technologies Inc RS7936 PCI Bridge 00:07.0 PCI bridge: ATI Technologies Inc Device 7937 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon Xpress 1250 03:01.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 03:01.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 03:01.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0b:00.0 Network controller: Broadcom Corporation BCM4321 802.11a/b/g/n (rev 03) I've tryied to install ati drivers 9.3 , which I downloaded and installed, unpacked and installed, builded and installed, but nothing worked. Looks like the latests version is just accepted to work on jaunty 9.04, so they are kind of old. what else I can do? thanks. Marc Information added: lsusb and lspci -n |grep 01:05.0 sysop@wl083517:~$ lspci -n |grep 01:05.0 01:05.0 0300: 1002:7942 sysop@wl083517:~$ lsusb Bus 006 Device 002: ID 413c:8138 Dell Computer Corp. Wireless 5520 Voda I Mobile Broadband (3G HSDPA) Minicard EAP-SIM Port Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 413c:8140 Dell Computer Corp. Wireless 360 Bluetooth Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 1b96:0001 N-Trig Duosense Transparent Electromagnetic Digitizer Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 03f0:1807 Hewlett-Packard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub sysop@wl083517:~$

    Read the article

  • How can I troubleshoot a "Hardware Malfunction" blue screen?

    - by AaronSieb
    My computer has suddenly started crashing to a blue screen with the following text: hardware malfunction call your hardware vendor for support *the system has halted* The crash occurs randomly during normal use. I have thus far always been able to reproduce it by transferring the contents of a large folder... But I'm not sure if this is caused by the file transfer, or simply because the transfer takes long enough for something else to trigger it. A bit about my hardware I have an dual core Intel CPU, and Asus motherboard. Video card is by nVidia, and connects via PCIe. My hard drives are in pairs, and connect via SATA to a RAID controller on the motherboard. They are configured to use a RAID0 configuration. What I've tried so far There is nothing in the Windows Event Log. WhoCrashed was unable to find any crash records. ScanDisk runs to completion (it launches prior to Windows load) and reports no errors. MemTest reports no errors (to 200% coverage). System temperatures are in the range of 40 to 50 degrees Celsius, with video card temperatures in the range of 60 to eighty degrees Celsius. I have stripped the system down to a minimal configuration (hard drive, video card, one memory module, motherboard, CPU, power supply). The problem still occurrs. However, this has allowed me to rule out a few components: It is not the video card because the problem still occurred after replacing the video card another one I had on hand. It is not the hard drive or anything software related because the problem occurred after a fresh installation of Windows on a replacement hard drive. It is not the hard drive cables because I replaced those with new ones and still had the problem. It is not the power supply because the problem still occurred after replacing the power supply with another one I had on hand. It is probably not the memory because I've tried three different memory modules in three different memory slots and was still able to replicate the issue. Is there anything I can do to confirm what's causing the issue? At the moment it seems as though it must be either the motherboard or CPU, but those are both difficult components to replace... In addition, both components are relatively new (two to three years old). I will gladly edit in any additional information I can get my hands on, and/or focus the question as I can find more details...

    Read the article

  • "The system time has changed" avents after waking from sleep

    - by Damir Arh
    Sometimes when my computer running Windows 7 wakes up from sleep, it has to adjust the time. When this happens the following system event is logged: <Event xmlns='http://schemas.microsoft.com/win/2004/08/events/event'> <System> <Provider Name='Microsoft-Windows-Kernel-General' Guid='{A68CA8B7-004F-D7B6-A698-07E2DE0F1F5D}'/> <EventID>1</EventID> <Version>0</Version> <Level>4</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x8000000000000010</Keywords> <TimeCreated SystemTime='2010-03-06T19:09:57.500000000Z'/> <EventRecordID>10672</EventRecordID> <Correlation/> <Execution ProcessID='4' ThreadID='56'/> <Channel>System</Channel> <Computer>GAME</Computer> <Security/> </System> <EventData> <Data Name='NewTime'>2010-03-06T19:09:57.500000000Z</Data> <Data Name='OldTime'>2010-03-06T17:34:32.870117200Z</Data> </EventData> <RenderingInfo Culture='sl-SI'> <Message>The system time has changed to ?2010?-?03?-?06T19:09:57.500000000Z from ?2010?-?03?-?06T17:34:32.870117200Z.</Message> <Level>Information</Level> <Task></Task> <Opcode>Info</Opcode> <Channel>System</Channel> <Provider>Microsoft-Windows-Kernel-General</Provider> <Keywords> <Keyword>Time</Keyword> </Keywords> </RenderingInfo> </Event> When this happens (I noticed it twice until now) the old time always corresponds to the time when computer entered sleep. The problem is that if Windows Media Center is scheduled for recording during this time, it just skips it as if the computer was turned off. I never had this problem running Windows Vista on the same machine. Any ideas what could be causing this problem and how to solve it are welcome.

    Read the article

  • All the Gear and No Idea: Suggestions for re-designing my home/office/entertainment network

    - by 5arx
    Help/ Advice/ Suggestions please: I have a load of kit that I love but which currently operate in disconnected, sometimes counter-productive way. Because I never really had a masterplan I just added these things one after another and connected them up in ad hoc ways. Since I bought my Macbook I've found I spend much less time on the MacPro that was until then my main machine. Perversely, as my job involves writing .Net software, I spend a lot of Mac time actually inside a Windows 7 VM. I stream media from the HP box to the PS3 and thus to the TV, but its not without its limitations/annoyances. We listen to each other's iTunes libraries but the music files are all over the place and it would be good to know they were all safely in one location (and fully backed up). I need to come up with a strategy that will allow me to use all the kit for work, play (recording live music, making tunes, iMovie work), pushing/streaming media to the TV and sharing files with my other half (she uses a Windows laptop and her iPod touch). Ideally I'd like to be able to work on any of the machines and have a shared homedrive that was visible to all machines so all my current files were synced up wherever i was. It would be great if I could access everything securely and quickly over the web. I'd also like to be able to set up a background backup process. The kit list thus far: Apple MacPro 8GB/3x250GB RAID0 + 1TB Apple MacBook Pro 13" 8GB/250GB - I spend a lot of my work time on a Windows 7 VM on this. Crappy Acer laptop (for children's use - iPlayer, watching movies/tv files) HP Proliant Server 4GB/80GB+160GB+300GB Sun Ultra 10 2 x 80GB (old, but in top-notch condition) PS3 160GB iPod Classic 2 x 8GB iPod Touch Observations: Part of the problem is our dual use of Windows and OS X - we can't go for a pure NT style roaming profile. Because the server is also used for hosting test/beta applications and a SQL Server db, it can't be dedicated to file serving. The two Macs really could do with sharing a roaming profile or similar. I'd love to be able to do something useful with the Ultra 10. My other half has been trying to throw it away for over five years now and regularly ask what function it serves in my study :-( I've got no shortage of 500GB external USB hard drives iMovie files are very large and ideally would be processed on a RAID system. Apple's TimeMachine isn't so great. If anyone could suggest all or part of a setup that would fulfil some of my requirements I'd be very grateful. I am willing to consider purchasing one or two more bits of kit (an Apple TV and a Squeezebox have been moted by friends) if they will help make efficiencies rather than add to the chaos and confusion. Thanks for looking.

    Read the article

  • Secondary DHCP server won't start on Centos 6.2

    - by Slowjoe
    I'm trying to create a backup DHCP server. Server times are in sync. Primary server starts fine. Secondary server won't start. Error from /var/log/messages is: Sep 15 14:47:45 stream dhcpd: Copyright 2004-2010 Internet Systems Consortium. Sep 15 14:47:45 stream dhcpd: All rights reserved. Sep 15 14:47:45 stream dhcpd: For info, please visit https://www.isc.org/software/dhcp/ Sep 15 14:47:45 stream dhcpd: /etc/dhcp/dhcpd.conf line 25: invalid statement in peer declaration Sep 15 14:47:45 stream dhcpd: #011max-response-default Sep 15 14:47:45 stream dhcpd: ^ Sep 15 14:47:45 stream dhcpd: /etc/dhcp/dhcpd.conf line 41: failover peer dhcp-failover: not found Sep 15 14:47:45 stream dhcpd: failover peer "dhcp-failover" Sep 15 14:47:45 stream dhcpd: ^ Sep 15 14:47:45 stream dhcpd: /etc/dhcp/dhcpd.conf line 49: failover peer dhcp-failover: not found Sep 15 14:47:45 stream dhcpd: failover peer "dhcp-failover" Sep 15 14:47:45 stream dhcpd: ^ Sep 15 14:47:45 stream dhcpd: WARNING: Host declarations are global. They are not limited to the scope you declared them in. Sep 15 14:47:45 stream dhcpd: /etc/dhcp/dhcpd.conf line 70: failover peer dhcp-failover: not found Sep 15 14:47:45 stream dhcpd: failover peer "dhcp-failover" Sep 15 14:47:45 stream dhcpd: ^ Sep 15 14:47:45 stream dhcpd: /etc/dhcp/dhcpd.conf line 78: failover peer dhcp-failover: not found Sep 15 14:47:45 stream dhcpd: failover peer "dhcp-failover" Sep 15 14:47:45 stream dhcpd: ^ Sep 15 14:47:45 stream dhcpd: Configuration file errors encountered -- exiting Sep 15 14:47:45 stream dhcpd: Sep 15 14:47:45 stream dhcpd: This version of ISC DHCP is based on the release available Sep 15 14:47:45 stream dhcpd: on ftp.isc.org. Features have been added and other changes Sep 15 14:47:45 stream dhcpd: have been made to the base software release in order to make Sep 15 14:47:45 stream dhcpd: it work better with this distribution. Sep 15 14:47:45 stream dhcpd: Sep 15 14:47:45 stream dhcpd: Please report for this software via the CentOS Bugs Database: Sep 15 14:47:45 stream dhcpd: http://bugs.centos.org/ Sep 15 14:47:45 stream dhcpd: Sep 15 14:47:45 stream dhcpd: exiting. Config file contents: # DHCP Server Configuration file. # see /usr/share/doc/dhcp*/dhcpd.conf.sample # see 'man 5 dhcpd.conf' # option domain-name "eng.foo.com"; option domain-name-servers ns0.eng.foo.com, ns1.eng.foo.com; option ntp-servers ntp.eng.foo.com; #option time-servers ntp.eng.foo.com; default-lease-time 3600; max-lease-time 7200; authoritative; log-facility local7; failover peer "dhcp-failover" { secondary; address 10.0.1.70; port 647; peer address 10.0.1.11; peer port 647; max-response-default 30; max-unacked-updates 10; load balance max seconds 3; } # # Management subnet # subnet 10.0.0.0 netmask 255.255.255.0 { option subnet-mask 255.255.255.0; option broadcast-address 10.0.0.255; option routers 10.0.0.1; option domain-search "eng.foo.com", "foo.com"; # Unknown clients get this pool pool { failover peer "dhcp-failover"; max-lease-time 300; range 10.0.0.240 10.0.0.249; allow unknown-clients; } # Known clients get this pool pool { failover peer "dhcp-failover"; max-lease-time 28800; range 10.0.0.150 10.0.0.199; deny unknown-clients; } include "/etc/dhcp/dhcpd.conf-engmgmt"; } # # Data subnet # subnet 10.0.1.0 netmask 255.255.255.0 { option subnet-mask 255.255.255.0; option broadcast-address 10.0.1.255; option routers 10.0.1.1; option domain-search "eng.foo.com", "foo.com"; # Unknown clients get this pool pool { failover peer "dhcp-failover"; max-lease-time 300; range 10.0.1.240 10.0.1.249; allow unknown-clients; } # Known clients get this pool pool { failover peer "dhcp-failover"; max-lease-time 28800; range 10.0.1.150 10.0.1.199; deny unknown-clients; } # For centos network installs if substring (option vendor-class-identifier, 0, 8) = "anaconda" { filename "/autohome/distro/ks/"; next-server eng-data.eng.foo.com; } # For PXE network installs if substring (option vendor-class-identifier, 0, 9) = "PXEClient" { filename "pxelinux.0"; next-server eng-data.eng.foo.com; } # For KVM PXE network installs if substring (option vendor-class-identifier, 0, 9) = "Etherboot" { filename "pxelinux.0"; next-server eng-data.eng.foo.com; } include "/etc/dhcp/dhcpd.conf-engdata"; }

    Read the article

  • Can't detect wireless networks, running ubuntu 9.10 on eeepc 1000he

    - by David Brown
    Hi, I am running Ubuntu 9.10 on an ASUS eeepc 1000HE, and my wireless card, RaLink RT 2860, is failing to recognize any wireless networks. It was working fine this morning, until I accidentally hit Fn F2, disabling the wireless card. I hit Fn F2 again to reenable it, but it no longer will detect any wireless networks (and other computers in the household do recognize them). Any help at all will be greatly appreciated! I googled quite a bit and talked to a human about this but could not fix it. We tried dhclient ra0, which returned There is already a pid file /var/run/dhclient.pid with pid 2438 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.2 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ Listening on LPF/ra0/00:25:d3:13:f4:20 Sending on LPF/ra0/00:25:d3:13:f4:20 Sending on Socket/fallback DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 6 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. No working leases in persistent database - sleeping. Other data: iwconfig returns (other stuff here...) ra0 RT2860 Wireless ESSID:"" Nickname:"RT2860STA" Mode:Auto Frequency=2.412 GHz Bit Rate=1 Mb/s RTS thr:off Fragment thr:off Link Quality=10/100 Signal level:0 dBm Noise level:-87 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ifconfig returns (other stuff here...) ra0 Link encap:Ethernet HWaddr 00:25:d3:13:f4:20 inet6 addr: fe80::225:d3ff:fe13:f420/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:583 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:19 ra0:avahi Link encap:Ethernet HWaddr 00:25:d3:13:f4:20 inet addr:169.254.7.117 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 Interrupt:19

    Read the article

  • Elasticsearch won't start anymore

    - by Oleander
    I restarted my elasticsearch instance 5 days ago and I haven't manage to start it since then. I get no output in the log file /var/log/elasticsearch/ nor does the elasticsearch binary print any information when running at using elasticsearch -f. I once manage to get this output. [2012-11-15 22:51:18,427][INFO ][node ] [Piper] {0.19.11}[29584]: initializing ... [2012-11-15 22:51:18,433][INFO ][plugins ] [Piper] loaded [], sites [] Running curl http://localhost:9200 resulted in curl: (7) couldn't connect to host. I've tried increasing the memory from 3gb to 10gb, but that didn't make any diffrence. Running /etc/init.d/elasticsearch start takes 30 seconds. ps aux | grep elasticsearch results in this output. /usr/local/share/elasticsearch/bin/service/exec/elasticsearch-linux-x86-64 /usr/local/share/elasticsearch/bin/service/elasticsearch.conf wrapper.syslog.ident=elasticsearch wrapper.pidfile=/usr/local/share/elasticsearch/bin/service/./elasticsearch.pid wrapper.name=elasticsearch wrapper.displayname=ElasticSearch wrapper.daemonize=TRUE wrapper.statusfile=/usr/local/share/elasticsearch/bin/service/./elasticsearch.status wrapper.java.statusfile=/usr/local/share/elasticsearch/bin/service/./elasticsearch.java.status wrapper.script.version=3.5.14 /usr/lib/jvm/java-7-openjdk-amd64/jre/bin/java -Delasticsearch-service -Des.path.home=/usr/local/share/elasticsearch -Xss256k -XX:+UseParNewGC -XX:+UseConcMarkSweepGC -XX:CMSInitiatingOccupancyFraction=75 -XX:+UseCMSInitiatingOccupancyOnly -XX:+HeapDumpOnOutOfMemoryError -Djava.awt.headless=true -Xms1024m -Xmx1024m -Djava.library.path=/usr/local/share/elasticsearch/bin/service/lib -classpath /usr/local/share/elasticsearch/bin/service/lib/wrapper.jar:/usr/local/share/elasticsearch/lib/elasticsearch-0.19.11.jar:/usr/local/share/elasticsearch/lib/elasticsearch-0.19.11.jar:/usr/local/share/elasticsearch/lib/jna-3.3.0.jar:/usr/local/share/elasticsearch/lib/log4j-1.2.17.jar:/usr/local/share/elasticsearch/lib/lucene-analyzers-3.6.1.jar:/usr/local/share/elasticsearch/lib/lucene-core-3.6.1.jar:/usr/local/share/elasticsearch/lib/lucene-highlighter-3.6.1.jar:/usr/local/share/elasticsearch/lib/lucene-memory-3.6.1.jar:/usr/local/share/elasticsearch/lib/lucene-queries-3.6.1.jar:/usr/local/share/elasticsearch/lib/snappy-java-1.0.4.1.jar:/usr/local/share/elasticsearch/lib/sigar/sigar-1.6.4.jar -Dwrapper.key=k7r81VpK3_Bb3N_5 -Dwrapper.port=32000 -Dwrapper.jvm.port.min=31000 -Dwrapper.jvm.port.max=31999 -Dwrapper.disable_console_input=TRUE -Dwrapper.pid=23888 -Dwrapper.version=3.5.14 -Dwrapper.native_library=wrapper -Dwrapper.service=TRUE -Dwrapper.cpu.timeout=10 -Dwrapper.jvmid=1 org.tanukisoftware.wrapper.WrapperSimpleApp org.elasticsearch.bootstrap.ElasticSearchF My current system: ElasticSearch Version: 0.19.11, JVM: 23.2-b09 Ubuntu 12.04 LTS I've tried re-install elasticsearch, removing old directories. Why can't I get it to start?

    Read the article

  • Postfix configuration - Uing virtual min but server is bouncing back my mail.

    - by brodiebrodie
    I have no experience in setting up postfix, and thought virtualmin minght do the legwork for me. Appears not. When I try to send mail to the domain (either [email protected] [email protected] or [email protected]) I get the following message returned This is the mail system at host dedq239.localdomain. I'm sorry to have to inform you that your message could not be delivered to one or more recipients. It's attached below. For further assistance, please send mail to <postmaster> If you do so, please include this problem report. You can delete your own text from the attached returned message. The mail system <[email protected]> (expanded from <[email protected]>): User unknown in virtual alias table Final-Recipient: rfc822; [email protected] Original-Recipient: rfc822;[email protected] Action: failed Status: 5.0.0 Diagnostic-Code: X-Postfix; User unknown in virtual alias table How can I diagnose the problem here? It seems that the mail gets to my server but the server fails to locally deliver the message to the correct user. (This is a guess, truthfully I have no idea what is happening). I have checked my virtual alias table and it seems to be set up correctly (I can post if this would be helpful). Can anyone give me a clue as to the next step? Thanks alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases broken_sasl_auth_clients = yes command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix debug_peer_level = 2 html_directory = no local_recipient_maps = $virtual_mailbox_maps mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man mydestination = $myhostname, localhost.$mydomain, localhost, $mydomain myorigin = $mydomain newaliases_path = /usr/bin/newaliases.postfix readme_directory = /usr/share/doc/postfix-2.3.3/README_FILES sample_directory = /usr/share/doc/postfix-2.3.3/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtpd_recipient_restrictions = permit_mynetworks reject_unauth_destination smtpd_sasl_auth_enable = yes soft_bounce = no unknown_local_recipient_reject_code = 550 virtual_alias_maps = hash:/etc/postfix/virtual My mail log file (the last entry) Sep 30 15:13:47 dedq239 postfix/cleanup[7237]: 207C6B18158: message-id=<[email protected]> Sep 30 15:13:47 dedq239 postfix/qmgr[7177]: 207C6B18158: from=<[email protected]>, size=1805, nrcpt=1 (queue active) Sep 30 15:13:47 dedq239 postfix/error[7238]: 207C6B18158: to=<[email protected]>, orig_to=<[email protected]>, relay=none, delay=0.64, delays=0.61/0.01/0/0.02, dsn=5.0.0, status=bounced (User unknown in virtual alias table) Sep 30 15:13:47 dedq239 postfix/cleanup[7237]: 8DC13B18169: message-id=<[email protected]> Sep 30 15:13:47 dedq239 postfix/qmgr[7177]: 8DC13B18169: from=<>, size=3691, nrcpt=1 (queue active) Sep 30 15:13:47 dedq239 postfix/bounce[7239]: 207C6B18158: sender non-delivery notification: 8DC13B18169 Sep 30 15:13:47 dedq239 postfix/qmgr[7177]: 207C6B18158: removed Sep 30 15:13:48 dedq239 postfix/smtp[7240]: 8DC13B18169: to=<[email protected]>, relay=gmail-smtp-in.l.google.com[209.85.216.55]:25, delay=1.3, delays=0.02/0.01/0.58/0.75, dsn=2.0.0, status=sent (250 2.0.0 OK 1254348828 36si15082901pxi.91) Sep 30 15:13:48 dedq239 postfix/qmgr[7177]: 8DC13B18169: removed Sep 30 15:14:17 dedq239 postfix/smtpd[7233]: disconnect from mail-bw0-f228.google.com[209.85.218.228] etc.aliases file below I have not touched this file - myvirtualdomain is a replacement for my real domain name # Aliases in this file will NOT be expanded in the header from # Mail, but WILL be visible over networks or from /bin/mail. # # >>>>>>>>>> The program "newaliases" must be run after # >> NOTE >> this file is updated for any changes to # >>>>>>>>>> show through to sendmail. # # Basic system aliases -- these MUST be present. mailer-daemon: postmaster postmaster: root # General redirections for pseudo accounts. bin: root daemon: root adm: root lp: root sync: root shutdown: root halt: root mail: root news: root uucp: root operator: root games: root gopher: root ftp: root nobody: root radiusd: root nut: root dbus: root vcsa: root canna: root wnn: root rpm: root nscd: root pcap: root apache: root webalizer: root dovecot: root fax: root quagga: root radvd: root pvm: root amanda: root privoxy: root ident: root named: root xfs: root gdm: root mailnull: root postgres: root sshd: root smmsp: root postfix: root netdump: root ldap: root squid: root ntp: root mysql: root desktop: root rpcuser: root rpc: root nfsnobody: root ingres: root system: root toor: root manager: root dumper: root abuse: root newsadm: news newsadmin: news usenet: news ftpadm: ftp ftpadmin: ftp ftp-adm: ftp ftp-admin: ftp www: webmaster webmaster: root noc: root security: root hostmaster: root info: postmaster marketing: postmaster sales: postmaster support: postmaster # trap decode to catch security attacks decode: root # Person who should get root's mail #root: marc abuse-myvirtualdomain.com: [email protected] My etc/postfix/virtual file is below - again myvirtualdomain is a replacement. I think this file was generated by Virtualmin and I have tried messing around with is with no success... This is the version without my changes. myunixusername@myvirtualdomain .com myunixusername myvirtualdomain .com myvirtualdomain.com [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected]

    Read the article

  • D-Link DIR-300 slows down / loses network

    - by basic6
    Hi there, there are 2 buildings (A and B). In bldg A is an open WLAN (which I'm allowed to use btw). In bldg B is a computer that I want to connect to that network. So I flashed an old D-Link DIR-300 AP with DD-WRT, mounted it to the wall (bldg B) near a window, attached a 13 dBi directional antenna (pointing to bldg A) and configured it as AP client in that wireless network. Then there's another AP, connected to the D-Link AP, acting as standard access point, which the computer is connected to. That's basically working so far, but: Every now and then the connection is lost. Not the connection between the computer and the D-Link (I can access the DD-WRT admin page normally) or the connection between the D-Link and the WLAN (in Status - Wireless it says it's still connected to the network), but when I want to access a web page (which only works if I'm connected to the wireless network from bldg A), my Firefox keeps "Looking for" (name resolution) without finding anything. When I reset the D-Link (power off, power on) in this situation, after some moments, everything's working fine again (Internet access). I've no idea why this is happening, but usually it's at most every few weeks (most times when nobody was using the computer, so no traffic). Compared to the connection speed when I connect directly to the WLAN in bldg A (Laptop), the speed in bldg B is rather slow, but I have the impression that this difference is worse in the last few days. A few minutes ago, I got 582 KB/s down and 911 KB/s up in bldg A (directly/laptop) and 84 KB/s down and 9 KB/s up in bldg B. The speed in bldg B used to be way higher (I remember 200 KB/s up) while the actual network speed in bldg A was lower than it is now (close to those 200). I'm aware that the wireless connection between those buildings should slow things down, but I'm wondering why this difference has become that extreme. Thanks for any tips... Update: I currently want to upload a large file (1.5 GB) via FTP (FileZilla). Since that caused the D-Link to disconnect (as described in first post), I took my laptop to bldg A, connected directly to the original WLAN (bypassing my D-Link) and tried the same upload. Guess what - same issue: At some point the connection is dead (at this point I would have reset my D-Link if I was connected to it). Just as the D-Link, my laptop is still connected, but not even name resolution is working ("Looking for..." in Firefox). After reconnecting, it's working again. Maybe my D-Link isn't the problem at all...

    Read the article

  • Some DHCP clients end up with wrong DNS server

    - by Nic Waller
    The scenario: DC running Windows Server 2008 R2 providing DNS + DHCP Cisco 1811 Router as the gateway 30 Windows XP DHCP clients on the LAN The problem: Some workstations are spontaneously switching to an incorrect DNS server. Specifically, ipconfig /all shows that they start using the gateway as a DNS server. This happens about 5-10 times a day to various computers, sometimes more than once per day. The workaround: Repairing the connection on the XP client always fixes the problem, and the correct DNS server address is obtained. We lost our main DNS/DHCP machine a week ago, and had to bring this one online as a spare. We've been having this issue since then. DHCP leases on the old and new servers are configured for "wired" (8 day) duration. There are definitely no other DHCP servers active on the LAN. So far there is no discernible pattern about which clients will show this problem, or when. When I ran DCDIAG /test:DNS it came back clean. Manual inspection of the DNS zone shows that all the records are appearing as expected, with no traces of the previous machine in there. Update Feb 27: Added screenshots. Here is a screenshot of the DHCP scope options on the 2008 R2 server. And here is a screenshot of ipconfig /all running on a healthy host. I don't have any ailing hosts at the moment, but will grab a screencap next time it happens. Update Feb 28: More screenshots. Here's a screenshot of DHCP and DNS traffic from a healthy client when repairing the local area connection. There's definitely only one server responding, but it does seem strange that the negotiation takes place twice. I'll try to get a similar capture from a sick machine this coming week. Update Mar 01: Caught a bad ipconfig. Here's a screenshot of ipconfig /all from a client that had this issue. It says the lease was issued this morning, but it doesn't even have an entry for the secondary DNS I set up yesterday. Both DNS servers were discovered properly when repairing the connection. Update Mar 01: It even got the sysadmin! This issue finally affected my personal workstation this morning. Unfortunately I had just rebooted and wasn't running a packet dump at the time. I set up a secondary server yesterday, and was logging all DNS traffic to it. My machine had not contacted the secondary DNS in over half an hour, so that says to me that it's just spontaneously reverting to the gateway without even failing over to secondary DNS first. Today I swapped the order of the DNS servers in DHCP, so the secondary is primary and vice versa. I will update again once I know how that goes.

    Read the article

  • Loose component cables causing HDMI video problems

    - by jwir3
    I'm not sure this is the correct forum, but I'll ask anyway. I have an A/V setup at home that has something like the following: Five Components (actually a few more, like a CD player, but they don't really relate to this question): Older Pioneer Receiver Digital Set Top Box Sony BluRay Player Samsung Plasma TV Speakers The reason for the receiver is so that all the sound can go through the speakers, rather than some going to the TV speakers and some to the external speakers. They are connected as follows: Digital Set Top Box connects via component video to Samsung TV directly via Component 2 (audio goes to Older Pioneer Receiver). Sony BluRay player is connected via HDMI 1 to TV, but audio goes to the receiver. Now, the problem I'm having is that when I have the digital set top box connected, there are times when the Netflix or Hulu streams I watch through the Sony BluRay player (it's connected to a router for internet access) will lose video. What I mean by this is that the sound of the episode will keep playing, but the screen will go black. If I jiggle the component cables, it will often come back. If I disconnect the component cables, it will always come back. I've noticed that one of the connections (the red component cable) doesn't like to sit very well in the component socket in the back of the digital set top box. It seems like there is a bad connection here, but it doesn't seem like this should be affecting the HDMI input at all. What I've noticed, though, is that when I disconnect the digital set top box completely (i.e. remove the component cable from the back of the TV), the problem seems to resolve itself. I'm not talking about actually removing the cable physically, because I thought perhaps the cables were mashing against one another, and possibly jiggling each other loose. To correct this possible problem, I took the component cable completely out of the cable ties it was in in the back of my entertainment center, as well as pulled the digital set top box out from the entertainment center altogether. It's now connected directly to the TV, without any other cables touching it to cause some kind of weird interference or just physical pulling on the cable. Same problem. If, however, I disconnect the component cable and just leave it sitting behind the TV, then the problem goes away. So, my question is this - what could be causing this? Is it a case where it's an improperly shielded component cable that's causing interference with the HDMI input, or something that's wrong with the TV? It's an intermittent problem, so it's difficult to track down. The TV isn't that old, so it's probably still under warranty. I'm just wondering if there is something else I can do that might reduce this problem without having to haul a massive television set out of my house to get repaired/replaced.

    Read the article

  • Lenovo Ideapad Y480 can't reinstall windows?

    - by elegantonyx
    Alright, so here's the deal... For a while, I wanted to mess with Linux. I don't know why, but I wanted to. So, what I did was use WUBI and install Ubuntu. Because of some unknown reason (Intel Rapid Start? Half the drivers being on a Lenovo-installed SSD [separate from the main hard drive]?) it wouldn't dual boot. So, I decided to use Linux Mint instead, and install it in a partition. Since Windows 7 Home Premium won't make partitions any more if you have a certain number already, I just shrank my system drive and left empty space for the installer to claim. When I installed Mint, it worked, but left my Windows 7 installation unable to boot and eventually it corrupted. I tried to use a system repair disc I burned earlier but it didn't find the Windows installation, so I assume the partition corrupted. I used this link:http://www.pcworld.com/article/248995/how_to_install_windows_7_without_the_disc.html to try and reinstall Windows. What happened was that originally it said that the partition I was trying to reinstall from had been locked down by the OEM (Lenovo). So, I went into GParted, wiped EVERYTHING, and selected 'Construct new Boot record' or whatever that function is, and now the error is: "Setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information." Does anyone know how to see the log files? Can anyone help? This system is a month old but the warranty only covers hardware failures, and I would need to pay around USD$60 for them to fix it. Please help. Any ideas? this is my main machine... Extra information: I have at my disposal: System Repair Disc (Burned myself) Windows 7 Home Premium 64 bit SP1 installation disk (burned from the pcworld links) Gparted Live CD Linux Mint 13 live cd A system backup (from the morning before this catastrophe) made using the Windows Backup and Restore. I put it on an external drive...that should be safe for now.

    Read the article

  • external hard drive is no longer recognized, gives buffer I/O errors

    - by BioGeek
    Hi all, The external hard drive which contains all my photos and where I backed-up all my important documents is no longer recognized. It is a three month old 500GB Iomage Prestige Desktop Hard Drive. When I plug it in, it is recognised as a USB device, because it shows up when I type lsusb, but dmesg gives this error message. [19712.013250] usb 2-2: new high speed USB device using ehci_hcd and address 21 [19712.145347] usb 2-2: configuration #1 chosen from 1 choice [19712.147214] scsi25 : SCSI emulation for USB Mass Storage devices [19712.147514] usb-storage: device found at 21 [19712.147519] usb-storage: waiting for device to settle before scanning [19717.148978] usb-storage: device scan complete [19717.149527] scsi 25:0:0:0: Direct-Access ST350082 0AS PQ: 0 ANSI: 2 CCS [19717.151020] sd 25:0:0:0: Attached scsi generic sg2 type 0 [19717.151685] sd 25:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) [19717.160402] sd 25:0:0:0: [sdb] Write Protect is off [19717.160412] sd 25:0:0:0: [sdb] Mode Sense: 34 00 00 00 [19717.160418] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165685] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165691] sdb: sdb1 [19719.171808] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19719.171818] sd 25:0:0:0: [sdb] Attached SCSI disk [19737.430998] sd 25:0:0:0: [sdb] Unhandled sense code [19737.431007] sd 25:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [19737.431016] sd 25:0:0:0: [sdb] Sense Key : Medium Error [current] [19737.431027] sd 25:0:0:0: [sdb] Add. Sense: Unrecovered read error [19737.431038] end_request: I/O error, dev sdb, sector 6160463 [19737.431050] Buffer I/O error on device sdb1, logical block 6160400 [19737.431060] Buffer I/O error on device sdb1, logical block 6160401 [19737.431067] Buffer I/O error on device sdb1, logical block 6160402 [19737.431075] Buffer I/O error on device sdb1, logical block 6160403 [19737.431082] Buffer I/O error on device sdb1, logical block 6160404 [19737.431088] Buffer I/O error on device sdb1, logical block 6160405 [19737.431096] Buffer I/O error on device sdb1, logical block 6160406 [19737.431102] Buffer I/O error on device sdb1, logical block 6160407 [19737.431114] Buffer I/O error on device sdb1, logical block 6160408 [19737.431121] Buffer I/O error on device sdb1, logical block 6160409 [19737.712183] sd 6:0:0:0: [sdb] Unhandled sense code [19737.712191] sd 6:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE [19737.712200] sd 6:0:0:0: [sdb] Sense Key : Hardware Error [current] [19737.712210] sd 6:0:0:0: [sdb] Add. Sense: No additional sense information [19737.712222] end_request: I/O error, dev sdb, sector 0 [19737.712232] Buffer I/O error on device sdb, logical block 0 Neither does the external drive show when I use fdisk: jeroen@phalacrocorax:~$ sudo fdisk -l [sudo] password for jeroen: Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000341ad Device Boot Start End Blocks Id System /dev/sda1 * 1 18714 150320173+ 83 Linux /dev/sda2 18715 19457 5968147+ 5 Extended /dev/sda5 18715 19457 5968116 82 Linux swap / Solaris` I popped the disk out of the casing put it on a SATA connect internally and then tried the file recovery programs testdisk/photorec and SpinRite, but both failed because they couldn't recognize the external harddisk. Do I have any other options?

    Read the article

  • Graphics driver for ubuntu on dell latitude XT

    - by marc.riera
    we have a laptop (dell latitude xt) on our company, and we would like to install ubuntu on it. windows 7 works fine out of the box, so the hardware is fine. since this laptop has a touchscreen we just installed ubuntu 10.10 netbook edition 32x. But, we do not manage to enable the touchscreen, neither the vga graphic drivers. this is the output from lspci, if somebody cares. 00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 7930 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS7932 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc Device 7934 00:06.0 PCI bridge: ATI Technologies Inc RS7936 PCI Bridge 00:07.0 PCI bridge: ATI Technologies Inc Device 7937 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon Xpress 1250 03:01.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 03:01.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 03:01.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0b:00.0 Network controller: Broadcom Corporation BCM4321 802.11a/b/g/n (rev 03) I've tryied to install ati drivers 9.3 , which I downloaded and installed, unpacked and installed, builded and installed, but nothing worked. Looks like the latests version is just accepted to work on jaunty 9.04, so they are kind of old. what else I can do? thanks. Marc Information added: lsusb and lspci -n |grep 01:05.0 sysop@wl083517:~$ lspci -n |grep 01:05.0 01:05.0 0300: 1002:7942 sysop@wl083517:~$ lsusb Bus 006 Device 002: ID 413c:8138 Dell Computer Corp. Wireless 5520 Voda I Mobile Broadband (3G HSDPA) Minicard EAP-SIM Port Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 413c:8140 Dell Computer Corp. Wireless 360 Bluetooth Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 1b96:0001 N-Trig Duosense Transparent Electromagnetic Digitizer Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 03f0:1807 Hewlett-Packard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub sysop@wl083517:~$

    Read the article

  • Restart mysql keeping the data

    - by sitonico
    I'm quite new using mysql, so let me know if I'm missing something. I took some holidays, and when I got back to work and I tried to log in phpmyadmin I got a ERROR 2002 (HY000): Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2). I never had this problem, so I was browsing to look for a solution. I tried some things, and I'm afraid I touched too much. I couldn't solve the problem, and the I realized that I had some actualizations to be done, and I thought that they may be helpful for mysql. Then I also realized that when I was doing this actualizations first day, they stopped because I had a lack of space, so I restarted then. Then,when the system was configuring mysql, it didn't advance. I waited for a long time and then I just stopped it and restarted the computer. After it, I just tried to uninstall mysql with sudo apt-get remove mysql-server-5.1, and install it again, but it didn't work. Now I have 2 questions: What do you think it is happening? Should I remove mysql completely? What should I do? I'm afraid of losing my databases, is there anyway to recover the data? Thank you very much in advance. -----------EDIT------- These are the messages: alfonso@alfonso-laptop:/$ tail -F /var/log/syslog | grep Feb 15 15:08:01 alfonso-laptop init: mysql post-start process (15192) terminated with status Feb 15 15:08:01 alfonso-laptop init: mysql main process (15263) terminated with status Feb 15 15:08:01 alfonso-laptop init: mysql main process ended, Feb 15 15:08:31 alfonso-laptop init: mysql post-start process (15264) terminated with status Feb 15 15:08:31 alfonso-laptop init: mysql main process (15358) terminated with status Feb 15 15:08:31 alfonso-laptop init: mysql main process ended, Feb 15 15:09:01 alfonso-laptop init: mysql post-start process (15359) terminated with status Feb 15 15:09:01 alfonso-laptop init: mysql main process (15447) terminated with status Feb 15 15:09:01 alfonso-laptop init: mysql main process ended, Feb 15 15:09:32 alfonso-laptop init: mysql post-start process (15448) terminated with status 1 This is the content of error.log-old 110128 13:17:20 [Note] /usr/sbin/mysqld: Normal shutdown 110128 13:17:20 [Note] Event Scheduler: Purging the queue. 0 events 110128 13:17:20 InnoDB: Starting shutdown... 110128 13:17:22 InnoDB: Shutdown completed; log sequence number 0 590872 110128 13:17:22 [Note] /usr/sbin/mysqld: Shutdown complete 110214 2:08:18 [Note] Plugin 'FEDERATED' is disabled. 110214 2:08:19 InnoDB: Started; log sequence number 0 590872 110214 2:08:19 [Note] Event Scheduler: Loaded 0 events 110214 2:08:19 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.41-3ubuntu12.8' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) -- Some links of similar problems https://bugs.launchpad.net/ubuntu/+source/mysql-dfsg-5.1/+bug/573318 http://www.linuxquestions.org/questions/linux-newbie-8/lamp-install-on-lucid-mysqld-sock-missing-mysql-terminating-status%3D1-853152/ It seems it's a permissions problem... But I don't know which permissions I should change... SOLVED -- mysql error 2002 "cannot connect to socket"

    Read the article

  • PHP: gethostbyname() suddenly no longer resolves names to IPs when run in Apache

    - by hurikhan77
    One of our older legacy servers which gets no further updates or reconfigurations suddenly stopped resolving hostnames to IPs when PHP is executed within Apache. However, it still works fine when executed from the CLI. From the RSS caches last modification time, I deduce that it stopped working on around Mar, 28th. To reproduce the problem, I created a script using fsockopen() and it said "connection failed (errno 2)". I further reduced the problem to being related with a failed name resolution: <?php $addr = gethostbyname("twitter.com"); echo "ADDR($addr)"; ?> When I run this through Apache, the output is ADDR(twitter.com), which is wrong. When I run this from the CLI, the output is ADDR(aaa.bbb.ccc.ddd) with varying IP addresses, as expected. Nothing on the server setup has changed. CLI and Apache module share the same php.ini. PHP is version v4.4.9 with Zend Optimizer v2.5.10. Apache is v1.3.31. I know the versions are old. But since nothing has been changed, a solution like "try to upgrade versions first" is no solution as the server's feature set/versioning is frozen and will be replaced soon. Still we need a solution. If I run dig through the script, it works in both environments (mod_php and CLI) but this is more than an ugly hack as it would involve many edits and testing throughout the whole script base which is also undesired as the PHP application on the server is frozen, too, and only receives security updates. It will be replaced by a complete rewrite (on the new server). But as the rewrite will take some time and successive replace parts of the legacy application, we need a fix for the resolver problem. I already googled a bit and while the problem is known, many did not find a fix. The fix to raise memory limits did not work. Restarts did not work. The resolver in mod_php just did stop working for no apparent reason. :-(

    Read the article

  • Optical SPDIF audio from motherboard not working with receiver

    - by simon b
    Hi, I hope someone can help; I can't get my SPDIF optical out working through my receiver and all the responses I can see on the web assume you have a sound card, while I settled for the (seemingly high end) sound on my motherboard (Asus P7P55D-E PRO), which appears to limit some of my options. My set-up is a "new out of the box" one and is: *Windows 7 PC (using PowerDVD10 for DVDs/Blurays and Windows media player for music) *Asus P7P55D-E PRO motherboard - has 8-channel audio TRS jacks and SPDIF optical and coaxial out *An old Yamaha receiver, whose only multi-channel input options are optical in and 6 channel RCA in. However, it still can handle DTS and DD *Boston Acoustic Soundware XS 5.1 speakers I've currently got the SPDIF optical out from the motherboard connected to the in on my receiver, have SPDIF enabled in the sound menu and the light is glowing red down the fibre. But I'm getting no sound at all. What I want is to be able to play DVDs/BluRays in 5.1 but also to be able to play music in multi-channel mode (even though I know this will be "fake" multichannel; it's more about where I sit in the room and my requirement to use the sub because the Boston is a satellite/sub set-up) My questions are: *Will optical work at all for multi-channel? THe latest posts I can see suggest it does but some people seem to say optical only outputs stereo. Whom to believe? *Even if it does work, I've read that I have to disable AC-3 decoding, or make various other changes, which don't seem to be possible without the menu options that a sound-card brings. Is the motherboard-only option just too inflexible? *Although my SPDIF device is enabled in the sound menu, it insists under "Jack information" that it is a "rear panel RCA jack", when of course it is not (both TOSLINK and rCA jacks do exist). Has the PC just forgotten that it has an optical? *I think I could relatively easily connect the 8-channel 3.5mm TRS jacks to my receiver 6-ch input jacks by way of TRS/RCA cables, but would that not stop me from being able to play music from media-player in multi-channel mode, as I'm not sure the motherboard can cope *Or do I need to bite the bullet and buy a sound-card? And if so, how can I be sure the one I get doesn't have the same problem? Any thoughts gratefully received, Cheers, simon

    Read the article

  • Ubuntu Lucid: Erratic screen behaviour after boot

    - by fgysin
    In short: about 50% of the time I have a screwed up monitor setup after reboot. About 50% it is totally correct. Now the longer version: I updated my machine from 9.04 to 10.04 (via 9.10). At first I run into some monitor problems (I have a 3-monitor setup) because of the known bug in the new xserver driver for xinerama. This messes up behaviour if the mouse goes either left or above the screen number 0, i.e. I had to make my left-most monitor screen 0. Everything worked out fine finally, I got my 3-monitor setup back with xinerama enabled to get one big desktop streched over 3 screens. Now the fun part: Every time I start up my machine only one of the 3 monitors gets a signal and is woken up: it only recognizes the left-most monitor (screen 0) and crams all the desktop stuff into this one screen. If I go into nvidia settings I only see one physical device although all 3 are connected and have power. When I look into the xorg.conf I can still see my old setup with 3 devices, 3 screens, xinerama active etc... But I was totally unable to get 3 montitors to work. (I tried unplugging monitors, reconfiguring whole nvidia setup, ...) But it gets even better: When I restart my machine (i.e. choose the restart option from the Ubuntu menu) it shuts down and tries to restart. The restart then gets stuck after showing the Ubuntu splash screen with the 'loading bar' (the moving dots thingy) and I am forced to kill the machine by cutting power. But after the power cut the machine boots up normally and suddenly I get my 3 monitor setup back up working. That is until the next time I shut down and start up, where it all starts over again and I only have one monitor... (see above) I really have a hard time seeing where the error is. It must be that the restart boot somehow differs from the 'normal' boot. But the fact that it gets stuck and I need to cut power which then basically triggers a 'normal' boot does not really support this theory... My setup (please tell me if you need further info): 3 monitors as 3 screens as one desktop (with xinerama) 2 nvidia cards where screen 0 and 1 are on card 0 and screen 2 is on card 1 Ubuntu 10.04 Lucid Lynx (updated from 9.10, 9.04, ....) I would appreciate every idea on the subject, at the moment I really don't have any clue what to do...

    Read the article

  • How to move a ruby on rails application to a new server

    - by ManiacZX
    I have a rails app on an old Ubuntu server I need to move onto a new machine. I haven't worked with ruby on rails so I don't really know anything about the structure of the app. I want to load this onto an Ubuntu 8.04 AMI on Amazon EC2 and am looking for any information regarding the migration process such as: Do I copy over the entire folder defined as the application root in the mongrel config (for ex: /u/apps/myapp/current) or just certain folders? Am I looking for trouble if I go with the latest versions of ruby and the various gems? Any general gotchas to look out for in the process. Current server information: root@webnode001:/# cat /proc/version Linux version 2.6.15-27-server (buildd@terranova) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP Fri Dec 8 18:43:54 UTC 2006 root@webnode001:/# rails -v Rails 1.2.3 root@webnode001:/# mongrel_rails cluster::configure --version Version 1.0.1 root@webnode001:/# gem -v 0.9.0 root@webnode001:/# gem list -l *** LOCAL GEMS *** actionmailer (1.3.3, 1.2.5) Service layer for easy email delivery and testing. actionpack (1.13.3, 1.12.5) Web-flow and rendering framework putting the VC in MVC. actionwebservice (1.2.3, 1.1.6) Web service support for Action Pack. activerecord (1.15.3, 1.15.2, 1.14.4) Implements the ActiveRecord pattern for ORM. activesupport (1.4.2, 1.4.1, 1.3.1) Support and utility classes used by the Rails framework. cgi_multipart_eof_fix (2.1) Fix an exploitable bug in CGI multipart parsing which affects Ruby <= 1.8.5 when multipart boundary attribute contains a non-halting regular expression string. daemons (1.0.7, 1.0.5, 1.0.4, 1.0.2) A toolkit to create and control daemons in different ways eventmachine (0.7.2, 0.7.0) Ruby/EventMachine socket engine library fastercsv (1.2.0, 1.1.0) FasterCSV is CSV, but faster, smaller, and cleaner. fastthread (1.0) Optimized replacement for thread.rb primitives ferret (0.11.4) Ruby indexing library. gem_plugin (0.2.2, 0.2.1) A plugin system based only on rubygems that uses dependencies only mongrel (1.0.1, 0.3.13.4) A small fast HTTP library and server that runs Rails, Camping, Nitro and Iowa apps. mongrel_cluster (0.2.1) Mongrel plugin that provides commands and Capistrano tasks for managing multiple Mongrel processes. mysql (2.7) MySQL/Ruby provides the same functions for Ruby programs that the MySQL C API provides for C programs. piston (1.3.3) Piston is a utility that enables merge tracking of remote repositories. rails (1.2.3, 1.1.6) Web-application framework with template engine, control-flow layer, and ORM. rake (0.7.3, 0.7.1) Ruby based make-like utility. sources (0.0.1) This package provides download sources for remote gem installation swiftiply (0.5.1) A fast clustering proxy for web applications.

    Read the article

  • Impossible to create/format install window 7 on unpartioned HD

    - by fra pet
    Hi guys i am getting nut reinstalling windows 7 on one of those Acer aspire all-in-one... The original OS(windows professional x64) was not starting, after the initial screen the bios was prompted. So step 1: i tried to access the system partition and reinstall everything but could not get at the point step 2: i set the bios to native ide and i tried to insert my original copy of windows professional and do a clean installation, but it does not allow me to format/create other partion form the installation mask step 3: my BAD, i tried to install ubuntu and i clean the whole hard drive, i was getting an error at some point during installation so i decided to get back to windows step 4: Windows 7 again, at the disk screen of the windows installation i entered into the prompt and played around with DISKPART... -i listed the disk and the HD was disk 0. -i selected disk 0. -i CLEAN disk 0 successfully. -i tried to create a CREATE PARTITION PRIMARY but gave an error cache corrupt and disk not up-to-date (after i try to create a partiton in disk 0 it disappear when i try LIST DISK and i have to restart before he can list DISK 0 again, RESCAN did not worked). -tried CLEAN ALL(2 hours) and succeeded. -try again to create primary partition and failed, same errors -try to install my old copy of windows xP pro and it seems to work, it create a partition, format(only quick worked, slow mode was at 0% after 1 hour so i stop), it start installing and around 90% installation said it could not copy a file and he stop -back on windows 7 again, it says that the hard drive has 490+gb unpartitioned but won't create a partition and format. -i tried again DISKPART as i though i messed up with the MBR when i installed ubuntu, so i did all of the instruction below http://www.sevenforums.com/tutorials/20864-mbr-restore-windows-7-master-boot-record.html http://support.microsoft.com/kb/927392 the errors were: on bootsect: the systne partiton was not found, Data error cyclic redundancy check on bootrec /FixMbr: A device attached to the system is not functioning but did not worked, and still can not partiton/format/install on a blank HD i tried some bootable clean disk tool and start infinite loop on the same errors the bios setting are: sata: native ide. if i put AHCL(or something like that does not load the HD and the DVD). quick start/quite start: disabled. Are there any other option or tools i can try before i try change the HD(That is my last option)? Thanks to everyone.

    Read the article

  • How to reset mysql's replication settings completely, without reinstalling it?

    - by user38060
    I set up mysql replication by adding references to binlogs, relay logs etc in my.cnf restarted mysql, it worked. I wanted to change it so I deleted all binlog related files including log-bin.index, removed binlog statements from my.cnf restarted server, works set master to '', purge master logs since now(), reset slave, stop slave, stop master. now, to set up replication again, I added binlog statements to the server. But then I hit this problem when restarting with: sudo mysqld (the only way to see mysql's startup errors) I get this error: /usr/sbin/mysqld: File '/etc/mysql/var/log-bin.index' not found (Errcode: 13) Because indeed, this file does not exist! (I deleted it, while trying to set up a new replication system) Hmm, if I change the config line to: log-bin-index = log-bin.index I get a different error: [ERROR] Can't generate a unique log-filename /etc/mysql/var/bin.(1-999) [ERROR] MSYQL_BIN_LOG::open failed to generate new file name. [ERROR] Aborting The first time I set up replication on this system, I didn't need to create this file. I did the same thing - added references to a previously non-existing file, and mysql created it. Same with relay logs, etc. I don't know why mysql insists on trying to read the old folder. Should I just reinstall the whole package again? That seems like overkill. my my.cnf: [client] port = 3306 socket = /var/run/mysqld/mysqld.sock [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] user = mysql socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp skip-external-locking bind-address = IP key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 8 myisam-recover = BACKUP table_cache = 64 sort_buffer =64K net_buffer_length =2K query_cache_limit = 1M query_cache_size = 16M slow_query_log_file = /etc/mysql/var/mysql-slow.log long_query_time = 1 log-queries-not-using-indexes expire_logs_days = 10 max_binlog_size = 100M server-id = 3 log-bin = /etc/mysql/var/bin.log log-slave-updates log-bin-index = /etc/mysql/var/log-bin.index log-error = /etc/mysql/var/error.log relay-log = /etc/mysql/var/relay.log relay-log-info-file = /etc/mysql/var/relay-log.info relay-log-index = /etc/mysql/var/relay-log.index auto_increment_increment = 10 auto_increment_offset = 3 master-host = HOST master-user = USER master-password=PWD replicate-do-db = DBNAME collation_server=utf8_unicode_ci character_set_server=utf8 skip-character-set-client-handshake [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash [myisamchk] key_buffer_size = 16M sort_buffer_size = 8M [mysqlhotcopy] interactive-timeout !includedir /etc/mysql/conf.d/ Update: Changing all the /etc/mysql/var/xxx paths in binlog & relay log statements to local has somehow solved the problem. I thought it was apparmor causing it at first, but when I added /etc/mysql/* rw, to apparmor's config and restarted it, it still couldn't read the full path.

    Read the article

  • Windows XP machine not seeing external FAT32 partitions correctly

    - by Rob_before_edits
    About 8 months ago my Windows XP machine stopped being able to see FAT32 external drives when I plug them in... mostly. I will explain... It happens with all my FAT32 drives, whether they be unpowered external hard drives, powered external hard drives, SDHC cards plugged directly into the machine's card reader, or SDHC cards plugged in via a separate USB card reader. All of these drives/cards used to work fine on this machine. They all stopped working at about the same time. NTFS volumes are not affected. If I plug in NTFS external drives they are recognized right away. I even have one external drive with two partitions on it, one is NTFS which is recognized, the other is FAT32, which is not recognized. If I attach a FAT32 drive, then reboot, then the drive almost always becomes visible to the machine after the reboot. Sometimes I can plug in a FAT32 drive and it works right away. Not often though. I'd say I get lucky more often with SDHC cards than hard drives. I'm developing a theory that I only get lucky with hard drives if I'm running Acronis Disk Director when I plug them in, though that usually doesn't work either - I need more data here, this may be a red herring. Getting lucky with a hard drive is really rare, usually I have to reboot. When a FAT32 is recognized, either because I got lucky or because I rebooted, I can almost never safely disconnect it. It tells me "The device 'Generic volume' cannot be stopped right now. Try stopping the device again later". I can't seem to get around this. IIRC, I've tried closing every open window, and still no luck. Since I care about my data usually the only way to disconnect a FAT32 drive is to shut down the machine. As you can imagine, two reboots just to read a drive is getting pretty old... When the machine fails to see a FAT32 drive it usually comes up with the appropriate drive letter and the words "Local Disk" in Windows Explorer instead of the correct partition name. If I click on it I get "J:\ is not accessible. The parameter is incorrect." Before this problem arose I always clicked the "safely remove" button for everything, including SDHC cards where I think it's not necessary. I've known for a long time that this is the correct procedure for hard drives, so I don't think failing to do this was the cause of this problem (before someone asks :) Any answers or suggestions most welcome.

    Read the article

  • Ubuntu Newbie Needs Assistance!!

    - by Steve Greene
    New Ubuntu User Needs Help!- version 9.10 does not communicate with laptop Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, even when sitting directly under the wireless router at the local library (literally), which puts out a wickedly-fast signal that my Windows Vista OS auto-detects and immediately connects to. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all, even though I am only a few feet from the router. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I desparately wish to convert to Ubuntu. I used Mac for ten years, and then Windows for ten years. Now, after 20 years, I want to live out my days as an open-source Ubuntu fanatic. I am ready to give the old status quo the boot! I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch so that I can move on in total Ubuntu bliss? My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System. I am running Windows Vista Home Basic, Service Pack 2. My current email is [email protected] if you have a workable solution that does not require programmer status to implement. Surely this must be a simple fix that I simply am overlooking, but being the new guy on the block, I have yet to be enlightened. Thanks for your help in coming up to speed!! Steve Wanna' be Ubuntu Fanatic "If you're not living on the edge, you're taking up too much space."

    Read the article

< Previous Page | 498 499 500 501 502 503 504 505 506 507 508 509  | Next Page >