Search Results

Search found 25669 results on 1027 pages for 'ill be back'.

Page 504/1027 | < Previous Page | 500 501 502 503 504 505 506 507 508 509 510 511  | Next Page >

• 12.04 update crash, now cannot boot

  - by EdW

  Boot now freezes the system at the "Ubuntu purple screen" with the 5 dots under it. I cannot even CTRL-ALT-F1 to get to an alternate console. Have to push reset button on computer to reboot. After the 12.04 update crash, the system would boot, but I had no icons and no launch bar and errors about missing dependencies. CTRL-ALT-F1 and ran apt-get -f install and it appeared to get the missing packages. I followed with a apt-get update; apt-get upgrade. It appeared to install all of the remaining 12.04 update packages. Rebooted to same blank screen - no icons, but got a compiz error. In console I tried "unity --reset" rebooted ... Nothing ... It's dead in the water. Tried to boot into Recovery Mode - black screen - I cannot even CTRL-ALT-Del - have to push reboot button. Fortunately, I have Mint on another partition and I can access the broken 12.04 partition. Ideas? I can back up all of my folders using Mint, but I would hate to have to do a new install.

  Read the article

• Cannot open an external hard drive in Windows

  - by SeeBees

  In Windows 7, I was installing wubi ubuntu to an external hard drive when suddenly it disconnected from the PC. After I connected it back to PC, and double clicked the drive's icon, Windows didn't show the content of the disk but asked me whether I wanted to format it. The hard drive has only one partition. Its format is NTFS. I also connected the disk to Windows XP. It makes the Windows Explorer super slow and I cannot open the disk as well. I can open the disk on Ubuntu and Mac. Is it possible to restore the disk and make it run in Windows? Thanks

  Read the article

• Disable discrete AMD GPU

  - by Smajl

  My notebook has two graphic cards and it suffers from severe overheating after installing Ubuntu (no problem with Windows 7 on the same machine). I figured out that the problem may be in the graphic card and I would like to disable the discrete one. I followed some tutorials on this topic (for example http://planetoss.com/articles/how-to-disable-the-discrete-amd-graphics-card-in-linux/). But the problem is, that after executing the commands, nothing really happens and both GPU are still running. Here is what I have done: smajl@smajl-mini:~$ sudo chown smajl /sys/kernel/debug/vgaswitcheroo/switchsmajl@smajl-mini:~$ echo IGD > /sys/kernel/debug/vgaswitcheroo/switch smajl@smajl-mini:~$ sudo cat /sys/kernel/debug/vgaswitcheroo/switch 0:IGD:+:DynPwr:0000:01:05.0 1:DIS-Audio: :Pwr:0000:02:00.1 2:DIS: :DynPwr:0000:02:00.0 smajl@smajl-mini:~$ echo OFF > /sys/kernel/debug/vgaswitcheroo/switch smajl@smajl-mini:~$ sudo cat /sys/kernel/debug/vgaswitcheroo/switch 0:IGD:+:DynPwr:0000:01:05.0 1:DIS-Audio: :Pwr:0000:02:00.1 2:DIS: :DynPwr:0000:02:00.0 What am I missing here? Also, more on the overheating topic: 1) Installed TLP 2) updated system 3) set power setting mode to "power save" ...and nothing helps Tried same thing with Linux Mint without success. Is there anything else to try if I manage to disable the second GPU and the problem preserves? Otherwise I would have to get back to win in order not to melt my laptop.. :-/

  Read the article

• How to force my laptop to use the discrete GPU?

  - by Anton Roth

  My laptop (Asus X7BSV) is stuck using only the integrated GPU. It has a nVidia GT540M as well, but I cannot get it to work. I am using a Windows 7 x64 with latest drivers. This occurred after I attached an external USB monitor I need for work, and since then I cannot swap back to the nVidia GPU (dxdiag for example says that the primary GPU is the Intel integrated one). Asus support asked me to completely reinstall the system, but that is something I do not want to do. I checked the BIOS, there is no option as to what GPU to use. The nVidia card itself is working, since I can use CUDA on it, and it worked with a Ubuntu Live CD. In the nVidia software management I tried setting it to global setting, high performance GPU (nVidia), but that had no impact. What am I missing here? I did uninstall/delete all drivers and software related to the external monitor, but that did not help.

  Read the article

• Wireless DHCP doesn't work until wired Ethernet plugged in

  - by MT_Head

  A client of mine has an Asus R1F tablet running Windows XP Tablet SP3. It has an Intel 3945ABG wireless card; wired Ethernet is a Realtek something-or-other. In the past few days, it's developed an odd problem: WiFi authenticates, but can't get an address via DHCP. plug in wired Ethernet - both interfaces get good addresses unplug cable, WiFi continues to work until shutdown. Next morning, repeat process. I've tried: turning WiFi off/on (there's a slider switch) disabling/re-enabling via Device Mangler uninstalling and reinstalling the driver for the 3945ABG... changing from Intel Pro/SET to Windows Wireless Zero Config (and back) restarting the router changing the static DHCP assignments at the router upgrading the router firmware, just on general principles The router/access point is pfSense 1.2.3RC1 (was 1.2.2); wireless card is Atheros-based. None of the 12 other users (5 with tablets) are having problems.

  Read the article

• The security database on the server does not have a computer account for this workstation trust relationship

  - by alex

  I have a Server 2008 machine called OTTO I recently, by mistake, booted up an old machine, also called OTTO (the hardware was unstable, so the new one was set up to take it's place) I shut down the old machine, turned it off, and recycled it (it won't ever be back on) Now, whenever i try to log in to the real OTTO with the domain account (mydomain\Administrator) i get the following error: The security database on the server does not have a computer account for this workstation What can I do to fix this? It doesn't appear in active directory any more I've added it, but I'm guessing this had no effect, due to a different SID I can log in as the local administrator however

  Read the article

• RPi and Java Embedded GPIO: Hooking Up Your Wires for Java

  - by hinkmond

  So, you bought your blue jumper wires, your LEDs, your resistors, your breadboard, and your fill of Fry's for the day. How do you hook this cool stuff up to write Java code to blink them LEDs? I'll step you through it. First look at that pinout diagram of the GPIO header that's on your RPi. Find the pins in the corner of your RPi board and make sure to orient it the right way. The upper left corner pin should have the characters "P1" next to it on the board. That pin next to "P1" is your Pin #1 (in the diagram). Then, you can start counting left, right, next row, left, right, next row, left, right, and so on: Pins # 1, 2, next row, 3, 4, next row, 5, 6, and so on. Take one blue jumper wire and connect to Pin # 3 (GPIO0). Connect the other end to a resistor and then the other end of the resistor into the breadboard. Each row of grouped-together holes on a breadboard are connected, so plug in the short-end of a common cathode LED (long-end of a common anode LED) into a hole that is in the same grouping as where the resistor is plugged in. Then, connect the other end of the LED back to Pin # 6 (GND) on the RPi GPIO header. Now you have your first LED connected ready for you to write some Java code to turn it on and off. (As, extra credit you can connect 7 other LEDs the same way to with one lead to Pins # 5, 7, 11, 13, 15, 19 & 21). Whew! That wasn't so bad, was it? Next blog post on this thread will have some Java source code for you to try... Hinkmond

  Read the article

• Sending changes to a terrain heightmap over UDP

  - by Floomi

  This is a more conceptual, thinking-out-loud question than a technical one. I have a 3D heightmapped terrain as part of a multiplayer RTS that I would like to terraform over a network. The terraforming will be done by units within the gameworld; the player will paint a "target heightmap" that they'd like the current terrain to resemble and units will deform towards that on their own (a la Perimeter). Given my terrain is 257x257 vertices, the naive approach of sending heights when they change will flood the bandwidth very quickly - updating a quarter of the terrain every second will hit ~66kB/s. This is clearly way too much. My next thought was to move to a brush-based system, where you send e.g. the centre of a circle, its radius, and some function defining the influence of the brush from the centre going outwards. But even with reliable UDP the "start" and "stop" messages could still be delayed. I guess I could compare timestamps and compensate for this, although it'd likely mean that clients would deform verts too much on their local simulations and then have to smooth them back to the correct heights. I could also send absolute vert heights in the "start" and "stop" messages to guarantee correct data on the clients. Alternatively I could treat brushes in a similar way to units, and do the standard position + velocity + client-side prediction jazz on them, with the added stipulation that they deform terrain within a certain radius around them. The server could then intermittently do a pass and send (a subset of) recently updated verts to clients as and when there's bandwidth to spare. Any other suggestions, or indications that I'm on the right (or wrong!) track with any of these ideas would be greatly appreciated.

  Read the article

• How to stop jucheck from running? Java won't remember "Check for Updates Automatically" setting.

  - by Ken

  I've installed Java on Windows Vista, and every day I get a Vista security warning asking me if I want to run "jucheck". Apparently this is the Java automatic updater. Well, I don't want it to run on its own, ever. I cancel it, and quit it. I right-click on the taskbar and unclick "Check for Updates Automatically", and then click "Never Check", and "Apply". And yet, it never remembers this setting. If I come back to the "Java Control Panel" right after clicking "OK", the very same box is checked again, all on its own. Is there some way to kill jucheck once and for all? If I simply delete jucheck.exe, will Java (other than the automatic check) still work, and will manual updates still work, and will it stop even trying to update every morning?

  Read the article

• Exchange mail users cannot send to certain lists

  - by blsub6

  First of all, everyone's on Exchange 2010 using OWA I have a dynamic distribution list that contains all users in my domain called 'staff'. I can send to this list, other people can send to this list, but I have one user that cannot send to this list. Sending to this list gives the user an email back with the error: Delivery has failed to these recipients or groups: Staff The e-mail address you entered couldn't be found. Please check the recipient's e-mail address and try to resend the message. If the problem continues, please contact your helpdesk. and then a bunch of diagnostic information that I don't want to paste here because I don't want to have to censor all of the sensitive information contained (lazy) Can you guys throw me some possible reasons why this would happen? If there are an innumerable number of reasons, where should I start to troubleshoot this? EDIT One Exchange server inside the network that acts as a transport server, client access server and mailbox server and one Edge Transport server in the DMZ.

  Read the article

• Social Retailing

  - by David Dorf

  For retailers the move to mobile has been obvious.  More and more consumers are interacting with retailers, both online and in the store, using their mobile devices.  Retailers are quick to invest in both consumer facing mobile apps as well as ones to equip employees.  But when I talk to retailers about social, the value isn't as clear-cut.  Intuitively, retailers know that better relationships with customers will result in higher sales, but the trip to get there has many paths. The interesting thing about social media is that it has the potential to permeate all parts of the business.  Obviously it works well for marketing, but it also has a place with recruiting, knowledge management, trend analysis, and employee collaboration.  Information gathered from social media can enhance existing processes like assortment planning, product development, space planning, promotion planning, and replenishment.  Letting the customer influence each of these areas helps align the experience. One of the things holding retailers back is the lack of consistent and integrated tools to manage social media and make sense of the huge amounts of data.  To that end Oracle has been aggressively acquiring in the space, as depicted in the infographic below.  Soon, social will get the same level of investment as mobile. The Social CRM Arms Race: A Timeline - An infographic by the team at Pardot Marketing Automation

  Read the article

• Adding extra fan on my setup. please advice on proper Exhaust or Intake of Fan.

  - by Pennf0lio

  Hi, I modify my Computer case so that I can add more computer fan to make my computer cool this summer. I would need your thoughts how I can improve my idea and I'm open to all of your advices. Status: Fan Position (The blue circles are the fan's location) At the side I have to intake blowing fresh air at the motherboard and at the top and back I have Exhaust fan blowing out hot air. The computer fans will be powered by 12v adapter (recycled) so that my power supply wouldn't be overloaded. I need a practical advice, I don't want to spend to much on this. Thanks.

  Read the article

• Windows 7 add printer, cancelled, but port still in use. How to remove?

  - by Jake

  I tried to add a network printer at www.xxx.yyy.zzz, but halfway it when it asked for a driver, I cancelled it because I do not have the driver at hand. Later when I try to add again, it tells me the port (www.xxx.yyy.zzz), which is automatically specified as the same as the IP for the printer, is already in use and then suggest www.xxx.yyy.zzz_1 Now, I cannot find the www.xxx.yyy.zzz printer anywhere such that I can remove it and use back the same port. How should I do it? Any ideas? Thanks.

  Read the article

• Correct nvidia+intel graphics setup in 14.04

  - by Espressofa

  Just upgraded to 14.04 to try to fix some other issues. Now, something has gone wrong with my graphics. I have a Thinkpad T530 with Intel and Nvidia graphics cards. $ inxi -SGx System: Host: xyz Kernel: 3.13.0-24-generic x86_64 (64 bit, gcc: 4.8.2) Desktop: N/A Distro: Ubuntu 14.04 trusty Graphics: Card-1: Intel 3rd Gen Core processor Graphics Controller bus-ID: 00:02.0 Card-2: NVIDIA GF108M [NVS 5400M] bus-ID: 01:00.0 X.Org: 1.15.1 drivers: fbdev,vesa,intel,nouveau (unloaded: nvidia) Resolution: [email protected] GLX Renderer: N/A GLX Version: N/A Direct Rendering: N/A $ glxinfo name of display: :0 Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Error: couldn't find RGB GLX visual or fbconfig Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Error: couldn't find RGB GLX visual or fbconfig Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". I'm not sure what I did but now something is wrong with my graphics, as should be visible from the above commands. nvidia-detector says "none" as well. I used to have bumblebee but then some website said to remove it and now something's clearly wrong. What's the right way to set things up? Should I try to add bumblebee back? Here's what's installed now: $ dpkg --get-selections | grep nvidia nvidia-319 install nvidia-331 install nvidia-libopencl1-331 install nvidia-opencl-icd-331 install nvidia-prime install nvidia-settings install nvidia-settings-319 install

  Read the article

• NT4 server generate too much weird DNS queries, How can i see the source PID?

  - by Hanan N.

  I have a NT4 server that in the last two weeks started to generate too many weird DNS queries to the DNS server is set to use. I have got warnings from the IPS system that it has blocked the responses from the DNS server back to the NT4 server. The queries it generate doesn't relate to any computer in the network, it is like 120624100088.xxxxxxx.net where xxx is the internal network, the numbers are just random at each query. I have done some research on how to get the PID that is generating the queries, and i found that only Process Monitor could give me that information, but since it is NT4 system Process Monitor doesn't work on it. It is a production server and i am just can't stop services as i want. I would like to get your advice on how can i get the PID that is generating these queries? Thanks.

  Read the article

• How do you apply development practices like version control, testing and continuous integration/deployment to system administration?

  - by arex1337

  Imagine you're going to manage a number of servers with a number of different services that's used by a number of people. Now say you want to reconfigure or replace some software on one of those servers. Obviously you don't want to work on servers that are in production. If this was a code change, as a developer, I would make the change on my local development machine, test it locally and commit the change to a version control system. The changes could then be deployed in a staging environment, tested further and finally deployed in a production environment. It would also be easy for me to roll back, if necessary. Generally, or specifically, how do you achieve this in system administration? (The first thing that comes to mind is to use virtual machines and put virtual machine images in version control, but I'm sure there is a lot of literature and clever solutions I'm not presently aware of.)

  Read the article

• How do I increase the open files limit for a non-root user?

  - by iCode

  This is happening on Ubuntu Release 12.04 (precise) 64-bit Kernel Linux 3.2.0-25-virtual I'm trying to increase the number of open files allowed for a user. This is for an my ecplise java application where the current limit of 1024 is not enough. According to the posts I've found so far, I should be able to put lines into /etc/security/limits.conf like this; soft nofile 4096 hard nofile 4096 to increase the number of open files allowed for all users. But, that's not working for me, and I think the problem is not related to that file. For all users, the default limit is 1024, regardless of what is in /etc/security/limits.conf (I have been rebooting after changing that file) $ ulimit -n 1024 Now, despite the entries in /etc/security/limits.conf I can't increase that; $ ulimit -n 2048 -bash: ulimit: open files: cannot modify limit: Operation not permitted The weird part is that I can change the limit downwards, but can't change it upwards - even to go back to a number which is below the original limit; $ ulimit -n 800 $ ulimit -n 800 $ ulimit -n 900 -bash: ulimit: open files: cannot modify limit: Operation not permitted As root, I can change that limit to whatever I want, up or down. It doesn't even seem to care about the supposedly system-wide limit in /proc/sys/fs/file-max # cat /proc/sys/fs/file-max 188897 # ulimit -n 188898 # ulimit -n 188898 So far, I haven't found any way to increase the open files limit for a non-root user, and I really don't want to be running my application as root. How should I properly do this? I have looked at all the posted and tried the given options but no luck!

  Read the article

• Tackling thin content on an images gallery

  - by Ted Wilmont

  We run an images gallery as part of our site, however we have over 8,000 images and every image has a separate HTML page of its own to display the image caption, related image and comments from users of the site. This seems to be a problem especially with the Google Panda update because these pages are technically "thin content". What would be the best way to tackle this? We'd love some feedback and advice regarding this scenario. We have a few options we thought of already but can't decide: We could noindex the separate image pages and loose any image search listings we have for the image in favour of removing these thin pages from the index. We could 301 all of the individual image pages back to the image category listing and anchor each image (e.g. #img2122) and include all of the comments and description on the category listing page itself. If we was to simply list all of the images and content on the category pages themself; what's the best method? We could add all of the content in the anchor tags and use jQuery to display them in a box when a user clicks on the image or we could use Ajax to retrieve the information. However, what's the best Ajax method for SEO? Any ideas, suggestions, tips or advice is greatly appreciated and thank you in advance for any given.

  Read the article

• Restoring GRUB2 on Software RAID 0 using LiveCD after Windows 7 wiped it

  - by unknownthreat

  I have installed Ubuntu 10.10 on my system. However, I need to install Windows 7 back, and I expect that it would alter GRUB and it did. Right now, my partition on my Software RAID 0 looks like this: nvidia_acajefec1 is Ubuntu 10.10 and nvidia_acajefec3 is Windows 7. I've been following some guides around and I am always stuck at GRUB not able to detect the usual RAID content. I've tried running: sudo grub > root (hd0,0) GRUB complains it couldn't find my hard disk. So I tried: find (hd0,0) And it complains that it couldn't find anything. So I tried: find /boot/grub/stage1 It said "file not found". Here's the text from the console: ubuntu@ubuntu:~$ grub Probing devices to guess BIOS drives. This may take a long time. [ Minimal BASH-like line editing is supported. For the first word, TAB lists possible command completions. Anywhere else TAB lists the possible completions of a device/filename. ] grub> root (hd0,0) root (hd0,0) Error 21: Selected disk does not exist grub> find /boot/grub/stage1 find /boot/grub/stage1 Error 15: File not found Fortunately, I got one person suggesting that what I've been trying to do is for GRUB Legacy, not GRUB2. So I went to the suggested website, ** (http://grub.enbug.org/Grub2LiveCdInstallGuide) **try to look around, and try: ubuntu@ubuntu:~$ sudo fdisk -l Unable to seek on /dev/sda This is just the step 2 of the instruction in the http://grub.enbug.org/Grub2LiveCdInstallGuide and I cannot proceed because it cannot seek /dev/sda. However, ubuntu@ubuntu:~$ sudo dmraid -r /dev/sdb: nvidia, "nvidia_acajefec", stripe, ok, 488397166 sectors, data@ 0 /dev/sda: nvidia, "nvidia_acajefec", stripe, ok, 488397166 sectors, data@ 0 So what now? Do you have an idea for how to make fdisk see my RAID array on live cd (Ubuntu 10.10)? Honestly, I am lost, very lost in trying to restore GRUB2 on this software RAID 0 system right now.

  Read the article

• RDS Replication across regions

  - by Bryan Migliorisi

  We are using Amazon AWS for our web services but given the recent instabilities in their infrastructure, we are trying to figure out how to run our application across multiple regions for additional redundancy. Ideally, we would run our entire app in a active-active configuration in multiple regions but our main concern is that we are using RDS, which I understand cannot replicate across regions. One possible solution (though we have not tried or proven it would work) would be to do mysqldump or EBS snapshots every hour or so but this would mean that we would be forced to run in an active-passive configuration. Our data would be at most an hour behind. This carries its own issues around data synchronization when we failover and the master comes back up, so its not the best solution. Are there any proven solutions for replicating RDS across regions?

  Read the article

• iSCSI RAID1 on two servers, fail scenario

  - by Franz Kafka

  Hallo, a simple question: Image I have two servers, each server has two disks in RAID1. Now I merge the two arrays with iSCSI to one RAID1 disk. Two questions: Can I do the merging of the 4 disks in one go? I can't image how. First I will have to install the os, and then the raid controller is already set up to RAID1. If a whole server fails the other server would continue working without any problems? Does iSCSI notice that the other server is missing and treet this as if the two disks were broken? When the server comes back online the data is resynced, as if I installed new disks into a array? Can I image that this way? Thanks alot.

  Read the article

• Deliver email to Gmail AND Office 365?

  - by gbegley

  We moved our Office app hosting from Google Apps to Office 365. Many of us miss Google Apps, especially its superior search functionality. The pressure to use Office 365 has disappeared; many (but not all) of us would like to go back to Google Apps. Is it possible to configure our domain's mail delivery so that messages are delivered to both Google Apps's Gmail and Office 365, allowing users to choose which platform they prefer? If so, what are the options? Google Apps documentation specifies the ability to deliver messages to a secondary mail server using routing configuration. Currently our MX records are point to Office 365. If I change the MX records to point to Google Apps Mails servers, is the "Office 365 MX record address" the address I would want to use for a Google Apps Routing Target?

  Read the article

• Switch monitor configurations on Windows 7

  - by Horst Walter

  I use one of my PCs for flight simulation as well as for home theater. In case one it has 2 monitors attached, and in case 2 (home theater) a HD TV is being used. All 3 monitors are attached at the same time to the graphics card. How could it best switch best between different configurations. In case 1 I'd like to have the configuration with monitor 1/2, alternatively I'd like quickly to switch to another config only with the HD TV as primary screen. A similar question has been asked 6 months back with no full solution yet, so I come up with it again. The comment there of Darius (Windows + P key) is the best so far.

  Read the article

• how can I pass an environment variable through an ssh command?

  - by Ross Rogers

  How can I pass a value into an ssh command, such that the environment that is started on the host machine starts with a certain environment variable set to my choosing? EDIT: The goal is to pass the current kde desktop ( from dcop kwin KWinInterface currentDesktop ) to the new shell created so that I can pass back an nfs locations to my JEdit instance on the original server which is unique for each KDE desktop. ( Using a mechanism like emacsserver/emacsclient) The reason multiples ssh instances can be in flight at one time is because when I'm setting up my environment, I'm opening a bunch of different ssh instances to different machines.

  Read the article

• UDF Partition reported full when it is not

  - by Capt.Nemo

  I was using these instructions to setup an external hard disk with udf. I have been able to setup a multi-partition system using those instructions, but I seem to have hit a wall, where the partition is reported as full while writing to the disk. Every other tool available to me reports it as free. Relevant lshw output Here's a screenshot showing the disk: Both the output of df and the file manager (caja) report the disk as free. Filesystem Size Used Avail Use% Mounted on /dev/sda9 9.0G 7.6G 910M 90% / udev 974M 12K 974M 1% /dev /dev/sda1 50G 47G 295M 100% /media/Data /dev/sda6 49G 41G 5.9G 88% /home /dev/sda2 155G 127G 29G 82% /media/Entertainment /dev/sda8 14G 13G 516M 96% /media/Stuff /dev/sdb2 120G 1.9G 112G 2% /media/3c887659-5676-4946-875b-b797be508ce7 /dev/sdb3 11G 2.6G 7.7G 25% /media/108b0a1d-fd1a-4f38-b1c6-4ad1a20e34a3 /dev/sdb1 802G 34G 768G 5% /media/disk I seem to have hit a wall near the 35GB mark. Despite being shown as 35gb/860gb used everywhere, the following happens on a write attempt: [2017][/media/Dory]$ echo D>>echo bash: echo: write error: No space left on device Writing byte by byte, the maximum I can take it to is 34719248K. The most weird part is that on mounting it Windows, Windows can write to the disk easily, and the writes are being read fine back in Ubuntu. However, the used-bytes remains at 34719248K in Ubuntu (It goes higher on Windows, however).

  Read the article

< Previous Page | 500 501 502 503 504 505 506 507 508 509 510 511  | Next Page >