Search Results

Search found 17953 results on 719 pages for 'someone someoneelse'.

Page 508/719 | < Previous Page | 504 505 506 507 508 509 510 511 512 513 514 515  | Next Page >

• Hardware Requirements & Tuning - Flash Media Server 3.5 Interactive

  - by Anthony Kanago

  I am trying to spec out a server to purchase (physically, not rented from someone like softlayer.com) to run an intranet instace of Flash Media Server 3.5 Interactive. In general, the server will likely be fielding somewhere on the order of 400 connections at a time at the upper limit. Of course, should this increase, we don't want to be stuck. While the decision is not final, we will likely be running the server on Red Hat rather than Windows. The server will be run on gigabit ethernet. I have two related questions: What sort of hardware would I need realistically to support this? What advice can you offer for settings in tuning FMS/the OS to be performant to this level? We are looking for a bare minimum that will run this effectively to save on costs. Realistically, the average number of connections will be fairly low (50-150) by comparison with that upper limit estimate. To reiterate: we just want to be cautious in not getting caught when we need more power, but we also need a low-cost solution (doesn't everyone?) and that may take priority. Windows and RedHat are the two officially supported operating systems. Since FMS is stated to be 32-bit only, I'm sticking with a 32-bit OS. The hardware requirements listed by Adobe on their website are: 3.2GHz Intel® Pentium® 4 processor (dual Intel Xeon® or faster recommended) 2GB of RAM (4GB recommended) 1Gb Ethernet card So what realistically do I need for those sorts of connection numbers, and what can I due to tune things up to get more out of less hardware? Thanks!

  Read the article

• How do I get more information on a potential network freeloader?

  - by Dov

  I have a home network set up, complete with a relatively good password. I'm in Mac OS X 10.6 (Snow Leopard) and have been noticing, on occasion, a computer showing up in my Finder's Shared section, that is not one of my own (the "pe-xpjalle" box pictured below). He has a tendency to come and go. How can I figure out his MAC address or something, so I can block him? I checked my "Logs and Statistics" in the Airport Utility, and didn't see that computer under DHCP clients. I'd rather not change my password, since I have quite a few devices I'd have to update. Is there any other reason he's show up on my network besides having guessed my password? Update: I fixed the Dropbox URL above (how embarrassing, I'm new to Dropbox. Thanks for the heads up, Doug.) Update 2: I tried clicking on "Connect as..." just for the hell of it, and got the dialog below. Now I have even less an idea what's going on than before. I don't have Parallels of VMware running, just the following: Transmission, NetNewsWire, Mail, Things, Safari, iTunes, Photoshop, Pages, Yojimbo, Preferences, AppleScript Editor, Software Update, Airport Utility, and Terminal. I don't think any of those create a virtual network machine, right? And no VMware machine of mine has ever had a name resembling "pe-xpjalle". Update 3: I just changed my passwords on both my N- and G-only networks, and I'm still seeing this, so I highly doubt that it's someone who's figured out my password (twice now). I'm really stumped.

  Read the article

• Puppet: array in parameterized classes VS using resources

  - by Luke404

  I have some use cases where I want to define multiple similar resources that should end up in a single file (via a template). As an example I'm trying to write a puppet module that will let me manage the mapping between MAC addresses and network interface names (writing udev's persistent-net-rules file from puppet), but there are also many other similar usage cases. I searched around and found that it could be done with the new parameterised classes syntax: if implemented that way it should end up being used like this: node { "myserver.example.com": class { "network::iftab": interfaces => { "eth0" => { "mac" => "ab:cd:ef:98:76:54" } "eth1" => { "mac" => "98:76:de:ad:be:ef" } } } } Not too bad, I agree, but it would rapidly explode when you manage more complex stuff (think network configurations like in this module or any other multiple-complex-resources-in-a-single-config-file stuff). In a similar question on SF someone suggested using Pienaar's puppet-concat module but I doubt it could get any better than parameterised classes. What would be really cool and clean in the configuration definition would be something like the included host type, it's usage is simple, pretty and clean and naturally maps to multiple resources that will end up being configured in a single place. Transposed to my example it would be like: node { "myserver.example.com": interface { "eth0": "mac" => "ab:cd:ef:98:76:54", "foo" => "bar", "asd" => "lol", "eth1": "mac" => "98:76:de:ad:be:ef", "foo" => "rab", "asd" => "olo", } } ...that looks much better to my eyes, even with 3x options to each resource. Should I really be passing arrays to parameterised classes, or there is a better way to do this kind of stuff? Is there some accepted consensus in the puppet [users|developers] community? By the way, I'm referring to the latest stable release of the 2.7 branch and I am not interested in compatibility with older versions.

  Read the article

• How can I make Mac OS X Address Book display a person’s home address from an LDAP server?

  - by Arcturus

  Hi, (I've posted this question on Stack Overflow first, but someone told me it belonged here.) I have a custom LDAP server, which I can customize to generate whichever object class and attributes I need. I'm trying to display people from that server in the Mac OS X address book. Names and organizations display correctly, as well as work-related phone and address. However, I've never been able to have a home address displayed in the address book. This is an example of output from running a ldapsearch: # extended LDIF # # LDAPv3 # base <dc=example,dc=com> with scope subtree # filter: (givenName=Joh*) # requesting: ALL # # 10041, example.com dn: uid=10041,dc=example,dc=com objectclass: top objectclass: person objectclass: organizationalPerson objectclass: inetOrgPerson objectclass: mozillaOrgPerson uid: 10041 cn: John Doe givenName: John sn: Doe o: Acme telephoneNumber: 500 00 00 mobile: 500 00 00 mail: [email protected] street: Baker St postalCode: 10098 l: New York c: US homePostalAddress: White St mozillaHomePostalCode: 10098 mozillaHomeLocalityName: New York mozillaHomeCountryName: US # search result search: 2 result: 0 Success # numResponses: 2 # numEntries: 1 Every piece of information shows up in the address book up to here: homePostalAddress: White St mozillaHomePostalCode: 10098 mozillaHomeLocalityName: New York mozillaHomeCountryName: US Which object class or attribute name should I use to have the home address show up in the Mac OS X address book?

  Read the article

• Windows Server 2008 SMTP & POP3 Configuration

  - by Alex Hope O'Connor

  This is the first time I have ever configured a VPS server without 3rd party applications such as Plesk control panel. I have got most functionality working in all my websites except I am very unsure as to how I can setup my email functionality on this new server. Basically I want the standard POP3 functionality, a bunch of accounts with private boxes, all able to send and receive emails using their individual usernames and passwords. My server setup is pretty simple, its a VPS with IIS & DNS Server running. What I have tried to do to setup SMTP & POP3 is adding the SMTP Server feature through the Server Manager Console (very unsure of the configuration as guides I found did not explain), I then installed a 3rd party application called Visdeno SMTP Extender as it claims to be a POP3 service providing accounting and the ability to communicate with email clients. That is as far as I have gotten as I can not seem to find too much information on the subject. So can someone please tell me how to go about configuring these services in order to provide standard SMTP & POP3 functionality? Thanks, Alex.

  Read the article

• How to setup a virtual host in Ubuntu?

  - by Rade

  I have an app that's accessible via 1.2.3.4/myapp. The app is installed in /var/www/myapp. I've set up a subdomain(apps.mydomain.com) that points to 1.2.3.4. I want the server to point to var/www/myapp if I type apps.mydomain.com/myapp, how do I do that? I have experience creating virtual hosts(lots of them) locally but I'm lost because it's now in production and it's a little different. Here's my virtual host config: <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName apps.mydomain.com/myapp DocumentRoot /var/www/myapp/public <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride All Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> Any idea why I still see the files instead of pointing me to the document root? Just in case someone might ask, the app is based on Laravel 4 framework. It's really bad right now because anyone can access the files from the browser.

  Read the article

• Trying to install ffmpeg-php and having installation issues.

  - by dallasclark

  I've installed ffmpeg successfully using the ffmpeginstaller 3 series (http://www.ffmpeginstaller.com/download). ffmpeg is working fine without any known issues with bash. The ffmpeginstaller is meant to install ffmpeg-php but it cannot be found and I receive an error when I execute php -v PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/ffmpeg.so' - /usr/lib64/php/modules/ffmpeg.so: cannot open shared object file: No such file or directory in Unknown on line 0 Looking at the '/usr/lib64/php/modules/' folder, it doesn't contain the ffmpeg.so file. I've tried to install ffmpeg-php manually but I receive the following error checking for ffmpeg headers... configure: error: ffmpeg headers not found. Make sure you've built ffmpeg as shared libs using the --enable-shared option Should I install ffmpeg with series 4 or 5 of ffmpeginstaller or does someone know how to fix this issue? Thanks in advance ! System Specs cat /etc/redhat-release CentOS release 5.5 (Final) cat /proc/version Linux version 2.6.18-028stab068.5 (root@rhel5-64-build) (gcc version 4.1.2 20070626 (Red Hat 4.1.2-14)) #1 php -v PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/ffmpeg.so' - /usr/lib64/php/modules/ffmpeg.so: cannot open shared object file: No such file or directory in Unknown on line 0 PHP 5.2.13 (cli) (built: Mar 2 2010 18:08:48) Copyright (c) 1997-2010 The PHP Group Zend Engine v2.2.0, Copyright (c) 1998-2010 Zend Technologies Any other details you need, just let me know.

  Read the article

• Can a wifi AP act as a client, and a server at the same time?

  - by nbolton

  I feel this is SF worthy (as opposed to SU) as I go into a bit of detail on gateways/routing. Here's my ideal setup (if possible) -- there is a wifi network (lets call it bob's) with which I want access to, but I have a few other computers on my network which I want to keep behind a firewall. So I was thinking of buying a wireless access point so that I could set it up to connect to bob's network from the AP, and then from my server, connect to the AP via ethernet. So that's the first bit. Second part is that I want to have my own private wifi network off the back of this; can I then tell the AP to serve a new network called foobar. When I say private network, I mean that my server is actually a Debian linux install with routing configured (and I also do some QoS stuff on, etc). So ideally, I'd like all the clients on the private network to be behind the server in terms of routing. However, if the private clients connect to the server via wifi, then aren't they exposed to the "public" network? That is, if someone is savvy enough to scan for my IP range. Also, to do routing I'd need to connect two ethernet cables between the server and the AP (because you can't do routing/QoS on virtual devices) -- which isn't a problem really; but I'm not sure whether the AP will allow me to separate the public and private LANs. Or, as well as the AP, am I better getting a wifi-to-ethernet adapter for the server? I could use a wifi usb, but this can be tricky to set up on headless linux; plus the signal strength is a bit lousy. If this question is a bit vague/spurious in places, please comment and I will explain in more detail.

  Read the article

• Disabling mouse acceleration in Mac OS X

  - by aib

  I've been looking for a solution to the unusable mouse problem in Mac OS X for ages. I've tried a gazillion programs and fiddled with every setting there is or there can be added. So far, I haven't found a way to get linear mouse response in Mac OS X. At this point I'm seriously considering installing another operating system. But before I do that, or go hacking around OS binaries, maybe someone here has a solution? I want linear mouse response. I want high sensitivity. I like my touchpad acceleration and would like to keep it if possible. Any ideas? P.S. I've been at this for a long time, I'll probably have already tried the most popular answers. I'm running Mac OS X 10.6.5 on a MacBook Pro. I don't use a particular brand of mouse. I'm not looking for any commercial solutions. I've tried: Mouse Acceleration Preferences Pane, the Snow Leopard version of which can get me close to a linear response, but at the cost of tracking speed (sensitivity). Answers on this question: Make Mac OS X mouse acceleration more Windows-like About every code snippet I found via Google.

  Read the article

• Can’t connect to SQL Server 2008 - looks like Shared Memory problem

  - by user38556

  I am unable to connect to my local instance of SQL Server 2008 Express using SQL Server Management Studio. I believe the problem is related to a change I made to the connection protocols. Before the error occurred, I had Shared Memory enabled and Named Pipes and TCP/IP disabled. I then enabled both Named Pipes and TCP/IP, and this is when I started experiencing the problem. When I try to connect to the server with SSMS (with either my SQL server sysadmin login or with windows authentication), I get the following error message: A connection was successfully established with the server, but then an error occurred during the login process. (provider: Named Pipes Provider, error: 0 - No process is on the other end of the pipe.) (Microsoft SQL Server, Error: 233) Why is it returning a Named Pipes error? Why would it not just use Shared Memory, as this has a higher priority order in the list of connection protocols? It seems like it is not listening on Shared Memory for some reason? When I set Named Pipes to enabled and try to connect, I get the same error message. My windows account is does not have administrator priviliges on my computer - perhaps this is making a difference in some way (as some of the discussions in this post about an "SuperSocketNetLib\Lpc" registry key seems to suggest). I have tried restarting the SQL Server service, by the way, and also tried to get someone to log onto the machine with an admin account to restart the SQL Server service. Still no luck.

  Read the article

• How to update the hard disk device drivers for a ghosted hard drive image so it can run on different hardware: Ultra ATA > SATA

  - by rism

  I've ghosted a Winxp machine from one laptop with Ultra ATA drive, and would like to set it up on another laptop as a multiboot option on another hard driver with a SATA drive. I can install the partition fine but if i make it active and try to boot it it blue screens. The blue screen is so fast i cant even read it, other than to make out it's saying "something", im picking probably hard drive as it goes through POST fine. So basically i would like to boot into my Win7 OS, and then somehow manipulate the XP partition to use updated drivers for the new hard drive/laptop so that i can then at least boot into the XP OS on the new machine and update all the other drivers in safe mode or whatever to get it to run. I assume someone is going to tell me to just do a fresh install, but that kinda defeats the purpose of ghosting at this point. There is a significant amount of personalisation, development setup on the XP machine that i would like to just transfer as is. As it stands ive invested minmal time in getting it to run, just a ghost and recovery and then a blue screen boot or two, so its still well worth it to me, time wise to try this way. Thanks.

  Read the article

• Time drift in Cloud Server - need to mainpulate GRUB config

  - by Aditya Advani

  We are hosting a VPS on a popular host and are experiencing a regular time drift of several minutes a day forward (approx 7). Linux Kernel: 2.6.18-164.11.1.el5 GNU/Linux Distro: CentOS release 5.4 (Final) We reached out to our hosting provider and their support advised us " This is a known issue with Cloud Servers. To fix this you will need to add one line to your grub config located at: /boot/grub/menu.lst The line you need to add is: noapic nolapic divider=10 nolapic_timer This should correct this issue. You will need to restart after this is added in. " Because I am wary of manipulating grub, mostly I'm terrified that our server may fail to restart - I ask you guys, the pro *nix admins - where exactly in this file does the recommended insertion below: # line from 1&1 for time syncing issue (Case 5163) noapic nolapic divider=10 nolapic_timer go? Please specify where exactly, and whether the order of commands is or is not important. Why is the block below "title CentOS ..." indented? If someone could give me an overview of how this works or point me to a resource that's easy to follow, that's what I'm looking for immediately, a light overview or basic understanding of what I;m doing. If GRUB and bootloaders are a deep dark treasure trove of kernel hacking or something, that's great well-recommended in-depth resources are also very welcome. This is my current /boot/grub/menu.lst # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file #boot=/dev/sda # serial --unit=0 --speed=57600 terminal --timeout=5 serial console timeout=5 title CentOS (2.6.18-164.11.1.el5) root (hd0,0) kernel /boot/vmlinuz-2.6.18-164.11.1.el5 ro root=/dev/hda1 console=tty0 console=tty initrd /boot/initrd-2.6.18-164.11.1.el5.img MOST IMPORTANT: I need to know where in the file above it is appropriate to paste the suggested line so I can confidently restart my VPS after manipulating GRUB config

  Read the article

• Inter-vlan routing issues

  - by DKNUCKLES

  I've been brought in to help administer a network and I've run into an issue - I'm not sure why this one is beyond me, however I figure an extra set of eyes on the problem may help resolve the issue. I have an HP MSM720 controller and at the time I'm trying to set up a basic hotspot set up with access points. For the time being I'm just looking to have people authenticate with a PSK and access the internet and other resources (namely printers) on other vlans. The user authenticates and the DHCP server on the controller gives them a 192.168.1.0/24 address. They are able to successfully browse the internet and ping machines on other networks, however they are unable to print to network printers that sit on the same LANs as the very computers that wireless clients can ping. The (extremely simplified) topology is as follows Computers on the wireless 192.168.1.1 network are able to ping computers on the 192.168.0.0 network, however cannot ping or print to the printers on the same network. I'm baffled and I have no idea why this is the case. Can anyone shed some light on this for me? Can someone spot the error of my configuration? EDIT : It should be noted that for whatever reason other computers on the 10.0.100.0/24 network cannot even ping the gateway of the Wireless Access network (192.168.1.1) - I'm not sure if this is relevant. These are the VLANS listed on the controller.

  Read the article

• Is it possible to be a Linux professional studying on your own?

  - by Marc Jr

  I read economics at university(nothing to see with linux, isn't it? :P). I have some basic knowledge about booting process, Linux Kernel compiling from source and stuff like that. But of course I have still much to learn sometimes some errors appears and "voila" I am lost. I had: Ubuntu, Fedora, OpenSuse, Arch.. using Gentoo now. I'd like to know what you linux users, professionals, administrators... would think it is the best way to learn linux in a professional way. Is it worth studying it and passing the LPIC test enough to work in the linux world? or do I need going to IT uni? I've heard LFS is a good way of learning about linux, is that real? I've been thinking about getting to LFS learn about more deeply about the linux process and learning scripts. It is possible to do this way? if anyone has a tip or a good way of doing, maybe someone did it. Any tip is very welcome. Words from a person in love with linux. :D The best, Marc

  Read the article

• ISA Server 2006 SSL Certificate Dilemma

  - by JohnyD

  I'm making so great headway in offering our services over https with help from a Go Daddy certificate, later to be upgraded to Thawte SSL123 certs. But, I've just run into one whopper of a problem. Here's my setup: I run an ISA 2006 firewall. Our web services are distributed over 2 servers. One is Windows 2000 (www.domain.com) and the other is Windows 2003 (services.domain.com). So, I'll need to purchase 2 certs for both www and services, import them into IIS6 on their respective machines, then export them with the primary key (making sure to Include all certificates in the certification path if possible... that had me stumped for a while), and then to finally import them into ISA's local computer Personal store. The problem I've just run into is that I have separate firewall rules for services.domain.com and www.domain.com... because requests need to be forwarded to different web servers. Each of these firewall rules use the same httplistener. I have just found out that you can only use 1 certificate per httplistener. To make matters worse you can only have a single httplistener per ip / port. Is this correct? I can only use a single certificate for a single ip address? This would seem to be a severe limitation. Am I wrong? If I'm not then I've got a whole lot more work ahead of me as I'll have to set up extra ip's, add them to the firewall's network interface, create new listeners using that ip, etc... Can someone please confirm that I'm doing this correctly / incorrectly? Once I got my head wrapped around it all it seemed easy... then this. Thanks in advance.

  Read the article

• Apple video adapters: Mini-DVI to DVI + DVI to video?

  - by Ken

  I have: a Macbook (which has Mini-DVI output) an Apple Mini-DVI to DVI adapter (so I can hook up my Macbook to my DVI LCD) a Mac mini (which has DVI output) I see that I can get a DVI-to-Video (s-video and composite) adapter from Apple that will let me hook up my Mac mini to my TV set (which has only component, s-video, and composite -- nothing digital). So far so good. Question: Will that same adapter also let me hook my Macbook to my TV? That is, can I hook Macbook - Mini-DVI to DVI - DVI to video - TV set, and see picture? I know there are digital/analog/integrated variants of DVI, and it's not at all clear to me what pins these things have and what signals they're sending. One website I found suggested that it would work, and another suggested that it wouldn't even physically connect. So I'm looking for, ideally, someone who's actually tried it, or has these adapters sitting around to try. I know I can buy 2 adapters (Mini-DVI to Video, and DVI to Video) to do this, but at $20 a pop I'll avoid that if at all possible.

  Read the article

• How do I decode this WordPress hack?

  - by Dennis Wurster

  I found an offending string in a client's WordPress-powered website, and I just want to know what it does. @preg_replace("\x40\50\x2e\53\x29\100\x69\145","\x65\166\x61\154\x28\142\x61\163\x65\66\x34\137\x64\145\x63\157\x64\145\x28\151\x6d\160\x6c\157\x64\145\x28\42\x5c\156\x22\54\x66\151\x6c\145\x28\142\x61\163\x65\66\x34\137\x64\145\x63\157\x64\145\x28\42\x5c\61\x22\51\x29\51\x29\51\x3b","\x4c\62\x68\166\x62\127\x55\166\x64\62\x56\151\x4c\63\x56\172\x5a\130\x4a\172\x4c\172\x49\167\x4d\152\x6b\165\x59\155\x6c\156\x4e\151\x39\172\x61\130\x52\154\x63\171\x39\151\x61\127\x63\62\x4c\63\x42\61\x59\155\x78\160\x59\61\x39\157\x64\107\x31\163\x4c\62\x5a\166\x63\156\x56\164\x4c\62\x4a\151\x4c\127\x6c\165\x59\62\x78\61\x5a\107\x56\172\x4c\62\x70\172\x4c\62\x70\170\x64\127\x56\171\x65\123\x38\165\x59\62\x46\152\x61\107\x55\166\x4c\151\x55\64\x4d\152\x68\106\x4a\124\x41\167\x4d\124\x4d\154\x51\152\x68\107\x4d\171\x56\103\x51\172\x46\103\x4a\125\x49\171\x4d\153\x49\154\x4e\105\x59\61\x4e\167\x3d\75"); Can someone outline the steps it takes to decode this? I know what preg_replace() is, but I don't know how to decode the arguments to the function, or how PHP processes it into something it can make use of.

  Read the article

• Windows roaming profile when creating a new user profile

  - by molecule

  When a particular user is having a lot of problems with Windows XP e.g. applications crashing, unresponsive applications (which used to work), and as a general troubleshooting practice for a domain user, I normally rename that user's old profile and get him/her to logon to create a "fresh" profile (on the same PC). More often than not, this will solve the problem albeit some reconfiguration i.e. Outlook, Excel add-ins etc. As I took over the systems admin role from another administrator, I would like to know what is the easiest way to find out (either through a third party or some Windows administrative tool) what settings are carried over if the profile is a Roaming Profile. I tested creating a new user profile for one of my users and it seems basic Outlook settings such as the user's mailbox and PSTs are carried over automatically when I create a new user profile. I suspect this is done through a batch file loaded as part of the login script. However, my knowledge of scripting is limited and I don't want any corruptions to be carried over to the new profile. Can someone share their experiences on this? Thanks in advance.

  Read the article

• PHP Startup: Unable to load dynamic library 'C:"\php\php_mysql.dll' - The specified module could not be loaded

  - by Tiny

  I'm trying to upgrade php 5.4.14 from php 5.4.3 in wamp server 2.2e. I have downloaded php-5.4.14-Win32-VC9-x86 (thread safe). Extracted it under C:\wamp\bin\php. Copied wampserver.conf from C:\wamp\bin\php\php5.4.3 to C:\wamp\bin\php\php5.4.14. Renamed php.ini-development to phpForApache.ini. -The port number the wamp server has been changed in the http.conf file to 8087 from its default 80. This is mentioned here though it is about upgrading from php 5.3.5 to php 5.4.0. After this, Restarting of the wamp server and services all over again has all been done and those two versions appeared in the menu php-versions (which is opened when the icon of the server is clicked). But when I attempt to enable a library like php_mysql or php_mysqli, a warning message box appears. PHP Startup: Unable to load dynamic library 'C:"\php\php_mysql.dll' - The specified module could not be loaded. I have also tried to removing the semicolon before them in the php.ini file but to no avail. I'm running Microsoft Windows XP Professional Version 2002, service pack 3. Where might be the problem? EDIT: I have changed extension_dir from C:\php to c:\wamp\bin\php\php5.4.14\ext\ in php.ini as the answer below indicates and the library is now loaded correctly but it says, 1045 - Access denied for user 'root'@'localhost' (using password: YES) though the user name and the password are the same as they are in MySQL in the config.inc.php file under phpmyadmin. I have also tried to restart MySQL56 service from Control Panel-Services(Local) but it keeps giving the same error. Does someone know why this happens?

  Read the article

• PXE booting LACP hosts on Force10 S50N with FTOS

  - by lolwutreddit

  Hardware: S50N Firmware: FTOS 8.4.2.6 Problem: We're trying to PXE boot some servers that are connected via port-channel interfaces with LACP. Current Work-around: we PXE boot a server with a single interface (eth0), and then use a Perl script to turn up the port-channel interfaces after the server is built. Details: Is anyone doing anything similar on Force10 S50 switches with FTOS? If not, is anyone doing this on another S series, or larger chassis-based Force10? I'm wondering if Native VLAN will solve this, since ports in a port-channel cannot explicitly have a VLAN set, and they don't seem to use the tagged or untagged VLAN that the port channel is in. I will confirm this next (I think it's the only thing I haven't tried) Juniper Example: http://broken.net/openindiana/how-to-pxe-boot-systems-on-lacp-using-juniper-switches/ Cisco: there are plenty of documented ways to solve this issue on IOS and Nexus Update/Edit: since there seems to be no way to use interface or port-channel mode commands to get the individual interfaces to show up in spanning-tree (rtsp in this case), the ports should never go into a forwarding state. I'm not going to mess with it anymore unless a) someone that has experience passes it on, or b) Force10 comes up with a solution for this (I'm guessing it will only be introduced on other S platforms (S55, S60), since the S50 seems to be near EOL). I'm basing that on the fact that the Open Automation type features are only being supported on the newer switches.

  Read the article

• Resolving "JBoss Web Console is Accessible to Unauthenticated Remote Users" vulnerability

  - by IAmJeff

  Our security team has determined there is a vulnerability in one of our systems. We are using version JBoss 5.1.0GA on RHEL 5.10. Vulnerability description: JBoss Web Console is Accessible to Unauthenticated Remote Users Yes, this looks familiar. Refer to Question 501417. I do not find the answer there complete. Can someone (or multiple someones) answer Does a newer version of JBoss fix this vulnerability? Are there links describing, in more detail, manual modification of JBoss configuration files to resolve the issue? Are there others options to remediate this vulnerability? Why don't I find the other answer complete? I'm not at all familiar with JBoss, so this answer seems a bit too simple. The web-console.war contains commented-out templates for basic security in its WEB-INF/web.xml as well as commented-out setup for a security domain in WEB-INF/jboss-web.xml. Just uncomment those basic security blocks and restart? Is there anything else I need to include? This seems generic. Do I need to include anything about my environment, such as absolute paths, etc.? Am I making this too complicated?

  Read the article

• Web Deploy 3.0 Installation Fails

  - by jkarpilo

  I am having difficulty installing Microsoft Web Deploy 3.0 to a Windows Server 2008 R2 box. I have tried installing with both the Web Platform Installer and the MSI package but installation fails while trying to execute the MSI custom action ExecuteRegisterUIModuleCA. This server is a VM and a member of a farm but shared config is disabled while I'm installing. Here's the point at which it fails in the MSI log (starting at line 1875): MSI (s) (80:FC) [15:29:01:358]: Executing op: ActionStart(Name=IISBeginTransactionCA,,) MSI (s) (80:FC) [15:29:01:374]: Executing op: CustomActionSchedule(Action=IISBeginTransactionCA,ActionType=3073,Source=BinaryData,Target=IISBeginTransactionCA,) MSI (s) (80:A8) [15:29:01:374]: Invoking remote custom action. DLL: C:\Windows\Installer\MSI6C6A.tmp, Entrypoint: IISBeginTransactionCA MSI (s) (80:FC) [15:29:01:436]: Executing op: ActionStart(Name=IISRollbackTransactionCA,,) MSI (s) (80:FC) [15:29:01:436]: Executing op: CustomActionSchedule(Action=IISRollbackTransactionCA,ActionType=3329,Source=BinaryData,Target=IISRollbackTransactionCA,) MSI (s) (80:FC) [15:29:01:436]: Executing op: ActionStart(Name=IISCommitTransactionCA,,) MSI (s) (80:FC) [15:29:01:436]: Executing op: CustomActionSchedule(Action=IISCommitTransactionCA,ActionType=3585,Source=BinaryData,Target=IISCommitTransactionCA,) MSI (s) (80:FC) [15:29:01:436]: Executing op: ActionStart(Name=IISExecuteCA,,) MSI (s) (80:FC) [15:29:01:452]: Executing op: CustomActionSchedule(Action=IISExecuteCA,ActionType=3073,Source=BinaryData,Target=IISExecuteCA,CustomActionData=1^3^21^WebDeployment_Current^154^Microsoft.Web.Deployment.UI.PackagingModuleProvider, Microsoft.Web.Deployment.UI.Server, Version=9.0.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35^1^1^0^^1^3^28^DelegationManagement_Current^171^Microsoft.Web.Management.Delegation.DelegationModuleProvider, Microsoft.Web.Management.Delegation.Server, Version=9.0.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35^1^1^0^^1^7^38^system.webServer/management/delegation^4^Deny^16^MachineToWebRoot^0^^3^yes^1^7^31^system.webServer/wdeploy/backup^4^Deny^20^MachineToApplication^0^^2^no^) MSI (s) (80:84) [15:29:01:452]: Invoking remote custom action. DLL: C:\Windows\Installer\MSI6CB9.tmp, Entrypoint: IISExecuteCA 1: IISCA IISExecuteCA : Begin CA Setup 1: IISCA IISExecuteCA : CA 'ExecuteRegisterUIModuleCA' completed with return code hr=0x8007000d 1: IISCA IISExecuteCA : CA 'IISExecuteCA' completed with return code hr=0x8007000d 1: IISCA IISExecuteCA : End CA Setup CustomAction IISExecuteCA returned actual error code 1603 (note this may not be 100% accurate if translation happened inside sandbox) Action ended 15:29:05: InstallFinalize. Return value 3. I can't seem to find any information regarding this particular issue; can someone help point me in the right direction?

  Read the article

• How to Protect Sensitive (HIPAA) SQL Server Standard Data and Log Files

  - by Quesi

  I am dealing with electronic personal health information (ePHI or PHI) and HIPAA regulations require that only authorized users can access ePHI. Column-level encryption may be of value for some of the data, but I need the ability to do like searches on some of the PHI fields such as name. Transparent Data Encryption (TDE) is a feature of SQL Server 2008 for encrypting database and log files. As I understand it this prevents someone who gains access to the MDF, LDF, or backup files from being able to do anything with the files because they are encrypted. TDE is only on enterprise and developer versions of SQL Server and enterprise is cost-prohibitive for my particular scenario. How can I get similar protection on SQL Server Standard? Is there a way to encrypt the database and backup files (is there a third-party tool)? Or just as good, is there a way to prevent the files from being used if the disk were attached to another machine (linux or windows)? Administrator access to the files from the same machine is fine, but I just want to prevent any issues if the disk were removed and hooked up to another machine. What are some of the solutions for this that are out there?

  Read the article

• Create new folder for new sender name and move message into new folder

  - by Dave Jarvis

  Background I'd like to have Outlook 2010 automatically move e-mails into folders designated by the person's name. For example: Click Rules Click Manage Rules & Alerts Click New Rule Select "Move messages from someone to a folder" Click Next The following dialog is shown: Problem The next part usually looks as follows: Click people or public group Select the desired person Click specified Select the desired folder Question How would you automate those problematic manual tasks? Here's the logic for the new rule I'd like to create: Receive a new message. Extract the name of the sender. If it does not exist, create a new folder under Inbox Move the new message into the folder assigned to that person's name I think this will require a VBA macro. Related Links http://www.experts-exchange.com/Software/Office_Productivity/Groupware/Outlook/A_420-Extending-Outlook-Rules-via-Scripting.html http://msdn.microsoft.com/en-us/library/office/ee814735.aspx http://msdn.microsoft.com/en-us/library/office/ee814736.aspx http://stackoverflow.com/questions/11263483/how-do-i-trigger-a-macro-to-run-after-a-new-mail-is-received-in-outlook http://en.kioskea.net/faq/6174-outlook-a-macro-to-create-folders http://blogs.iis.net/robert_mcmurray/archive/2010/02/25/outlook-macros-part-1-moving-emails-into-personal-folders.aspx Update #1 The code might resemble something like: Public WithEvents myOlApp As Outlook.Application Sub Initialize_handler() Set myOlApp = CreateObject("Outlook.Application") End Sub Private Sub myOlApp_NewMail() Dim myInbox As Outlook.MAPIFolder Dim myItem As Outlook.MailItem Set myInbox = myOlApp.GetNamespace("MAPI").GetDefaultFolder(olFolderInbox) Set mySenderName = myItem.SenderName On Error GoTo ErrorHandler Set myDestinationFolder = myInbox.Folders.Add(mySenderName, olFolderInbox) Set myItems = myInbox.Items Set myItem = myItems.Find("[SenderName] = " & mySenderName) myItem.Move myDestinationFolder ErrorHandler: Resume Next End Sub Update #2 Split the code as follows: Sent a test message and nothing happened. The instructions for actually triggering a message when a new message arrives are a little light on details (for example, no mention is made regarding ThisOutlookSession and how to use it). Thank you.

  Read the article

• How can I manually install pecl_http on Ubuntu 9.10?

  - by Richard

  This is essentially a repost of http://stackoverflow.com/questions/4159369/ubuntu-9-04-pecl-extension-downloads-but-does-not-install. Hoping maybe someone can help me here. I've done this: sudo apt-get install php-pear sudo apt-get install php5-dev sudo apt-get install libcurl3-openssl-dev which installs fine. However, the next step: sudo pecl install pecl_http Doesn't install the extension, but merely downloads it. There are no error messages. So I have unpacked it and built it myself per http://php.net/manual/en/install.pecl.phpize.php Essentially: cd pecl_http phpize ./configure make make install I also make test'd to check all ok - and it failed one test: HttpRequest, which is kind of fundamental to this package. And indeed this doesn't work: $r = new HttpRequest('http://www.google.com'); $r->send; echo $r->getResponseCode(); No request is sent, the response code is zero, but no errors either. How can I get this damn thing installed? Is this a bug? Am I doing something wrong? Any alternatives, workarounds? Help appreciated. Thanks

  Read the article

< Previous Page | 504 505 506 507 508 509 510 511 512 513 514 515  | Next Page >