Search Results

Search found 16793 results on 672 pages for 'sharepoint services'.

Page 509/672 | < Previous Page | 505 506 507 508 509 510 511 512 513 514 515 516  | Next Page >

• Service or software to auto-sync one server to another so they are identical?

  - by Ryan

  We have a main node in a DC data center and want to setup a back-up node in Seattle. The back-up node will only be used if the DC node goes down and we switch it over while DC node is repaired. The question is, what kind of services out there allow me to sync the data, I suppose we want to do it fairly frequently so if something goes down there isn't much loss in data between the time of failure and the last back-up/sync. Is there any common solution for this? It's Windows Server 2003 running Parallels Virtuozzo.

  Read the article

• How to accelerate and notice failure of potentially faulty disks

  - by rainier

  Hey, I got a bunch of 'used' servers, whose disks should have been checked, but they have been shipped around the county in crate which can't help. I just had one disk go bad (despite being mirrored, currently trying to get more details). The server was fine for about a week before everything ground to a halt this afternoon. Is there any way 'accelerate' the failure of faulty disks, with the goal of bringing the disk to failure before we launch production services? Would doing lots of I/O with 'dd' or 'iozone' be a good way to test these potentially faulty disks? Any other tests/tools that would help recognized failures before they happen?

  Read the article

• Windows Server 2003: Nat Port Forwarding Not Working

  - by jM2.me

  The setup is following: Internet (108.99.XXX.XX) <- Windows Server 2003 (10.0.0.1) <- Switch <- Office Computers (10.0.0.100-200 some static routes some manual some automatic) Windows Server has NAT installed on it and two network interfaces are configured properly. The problem is, whenever I try to forward port 80 (or any other) from office computer (lets say 10.0.0.100), it fails. Nic #1 Settings: All settings are obtained from ISP Nic #2 Settings: Set manually IP: 10.0.0.1 Mask: 255.255.255.0 Nat Server is configured to automatically assign IP addresses to private network. Settings are: IP: 10.0.0.0 Mask: 255.255.255.0 Forwarding was done in Routing and Remote Access (local) - IP Routing - NAT/Basic Firewall - Local Area Connection (right click_properties) - services and ports - Web Server HTTP - Private Address: 10.0.0.100 SO what is causing the problem of failure to forward any port from other computer inside private network?

  Read the article

• Lost support for Web Access on Verizon BlackBerry World Edition

  - by Jimsmithkka

  Hello all, I believe that some silliness has occurred with my blackberry after a OS upgrade. I have 2010 Blackberry world edition phone, purchased off a friend who went iPhone, that at first worked with web on the Verizon network. When i connected it to my PC to transfer contacts, it prompted for an OS upgrade, which I performed. Post-Upgrade I have found that i can no longer access any of the web services: eg. AppWorld, Email, Twitter, Browser. And they all state that i need to upgrade my account to gain access. I had a Storm previous to this that worked fine, and at the VZ store they told me this device is no longer supported (new in 2010 though), and they got me a free "upgrade" to the Blackberry flip. What i could use help with is finding a source stating it is discontinued or a guide that will help me re-enable the web features. I can provide further info later if needed (currently at work with the flip, the WorldEdition is at home).

  Read the article

• Should a MobiTex service with a highly resilient website offer content over WAP?

  - by makerofthings7

  I'm trying to offer services over the MobiTex network (also see wiki) and want to reduce double-work. I'm trying to understand if it is a good idea to WAP enable my website. Given that WAP usage is increasing (since MMS is a hybrid of SMS + WAP), and the FCC has required every operator in the 700Mhz range to implement it I'd like to fully understand if there are benefits to the technology for certain critical applications. For example, if GPRS allows SMS traffic, voice, and Data, presumably they are handled by different Gateways. If there is another gateway for WAP traffic I would think that it would act as a backup if the data gateway was overloaded. Are there resiliency benefits to using WAP on a critical website? i.e. Content delivery (push or pull)

  Read the article

• Failing RAM, or something else?

  - by Thanatos

  I have a IBM Thinkpad T43, currently running Windows XP. Programs were crashing, XP was blue-screen-of-deathing, (more than usual) - it was basically unusable, but I couldn't get any informative error out of XP. I booted Ubuntu off a thumbdrive, which made it to the desktop, but as soon as I started to try to do anything, X segfaulted, along with several other services, followed quickly by kernel warnings and a kernel panic. I'm currently running Memtest86+ on this machine, which is spitting out numerous errors. (16k over 3 passes, and counting) The failing areas are numerous, and look something like this: 0001055da4 - XX.X MB, etc. The addresses that fail seem to cluster around 0-20 MB, 250MB, and, more rarely, 750MB, 1000MB, and 1200MB. However, a lot (but not all) of the failing addresses that I've seen end in XXXXXXX?da4 where the ? is a 1 or a 5. The machine has two sticks of RAM, one 512MB, one 1024 MB, the 512MB mapped to the lower addresses, the 1024 MB stick following. Is this indeed RAM failure, or should I consider other things before purchasing more RAM?

  Read the article

• iPhone game center can't create sandbox account

  - by William Jockusch

  Whenever I try to create an account on the simulator or device, I get a message "game center account services are currently unavailable. Please try again later." Furthermore, I have never been able to sign in to the game center app on the simulator. Interestingly, if I reset my device with iTunes, I can then log in to the Game Center app with my regular apple id. But whenever if I log out, then try to create a sandbox account for an app I am developing, it always fails as described above. Any suggestions?

  Read the article

• How can i use one Domain Controller to manage 3 separate small firms

  - by Plamen Jordanov

  currently we have one Domain Controller that have 15 users and cup off services(hMailServer, IIS, DNS, Active Directory). Now the owners of the firm created two new firms which computers and networks are my responsibility. Now i wonder how exactly to join users in existing domain. Did you think that is a good idea to just include all computers and user from all firms under one domain or there is another solution ? Did some of you run into this kind of situation and what did you do ? ---Edit--- Brent, Dan thank for info guys. For now i will follow Brent advice until we get the new server witch we will virtualize and the old server will be our second DC on different location. Heck we even might think some Pay-as-you-go VPS solution for DC redundancy.

  Read the article

• Linux router with diffent gateways for incomming and outgoing connections

  - by nkout

  I have the following topology: LAN Users:192.168.1.2 - 254 (192.168.1.0/24) gateway1: 192.168.2.2/24 used for all outgoing connections of LAN users (default gateway) gateway2: 192.168.3.2/24 used for incoming services (destination NAT, ports 80,443 are forwarded to 192.168.2.1) linux router-server R eth0 192.168.1.1/24: LAN eth1 192.168.2.1/24: WWAN1 eth2 192.168.3.1/24: WWAN2 I want to: route all outgoing traffic coming from LAN and R via 192.168.2.2 route the responses to incoming connections via 192.168.3.2 My config: ifconfig eth0 up 192.168.1.1 netmask 255.255.255.0 ifconfig eth1 up 192.168.2.1 netmask 255.255.255.0 ifconfig eth2 up 192.168.3.1 netmask 255.255.255.0 echo 0 >/proc/sys/net/ipv4/ip_forward route add default gw 192.168.2.2 iptables -t nat -A POSTROUTING -d !192.168.0.0/16 -j MASQUERADE I want to add iptables rule to mark incoming traffic from WWAN2 and send back the responses to WWAN2, while keeping default gateway on WWAN1

  Read the article

• Interested in scp recipe for sftp [closed]

  - by GJZ

  You wrote in a reply this Blockquote The problem is that sftp runs as the user's id -- first, the sftp client ssh's into the target host as the given user, then runs sftp-server. Since sftp-server is running as a regular user, it has no way to "give away" a file (change owner of a file). However, if you are able to use scp, and assign a key pair to each user, you can get around this. This involves adding a user's key to root's ~/.ssh/authorized_keys file, with a "command=" parameter to force it to run a script that sanitizes and alters the arguments of the server-side scp program. I've used this technique before to set up an anonymous scp dropbox that allowed anyone to submit a file, and ensure that no one could retrieve submitted files and also prevent overwrites. If you are open to this technique, let me know and I'll update this post with a quick recipe. We are interested in this scp quick recipe for our community services file sharing. Best Regards, Gert Jan Zeilstra

  Read the article

• FreeBSD 9 (amd64) reboot/shutdown process is very slow

  - by nbari

  I have a Dell Poweredge 2900 III with FreeBSD 9 (amd64), the server uses mfi wich handles a raid10, I had to reboot the server, but notice that either when rebooting or shutting down the server, something is going wrong, besides taking to much time to reboot/shutdown, after rebooting I notice that that some ldap instances within some jails could'nt start and this was because the database was corrupted. This make me think that probably something was wrong with the disks or mfi card, but checking the disk array / logs everything seems to be working fine. My set up is something like this: Host server has the minimum base of FreeBSD 9 amd64, within I create some jails, the ones contain services like mysql, email, and some others ldap. With FreeBSD 7 and 8 I didn't notice this behavior but with FreeBSD 9 something is not working well. I did a clean installation of FreeBSD 9 and root filesystem is using ZFS. Attached is an image hoping some one can give me a hint of what to check or any kind of advice. reboot capture screen image

  Read the article

• How do I set logfile rotation limit for CF8 -out logs?

  - by melikeum

  I'm trying to set the number of logs to keep for the CF -out logs. I found a jrunsvc command line switch to set this but it throws an error saying the value must be at least 1000: jrunsvc.exe -logfileRotationLimit 50 "ColdFusion 8 Application Server" Error: log file rotaion limit must be at least 1000 The default is 200 files which seems excessive but 1000 is even worse. Am I not understanding this value properly? I did set it to 1001 and then I found this registry entry: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\ColdFusion 9 Application Server\LogFileRotationLimit I'm hesitant to set it there manually in case the value does not equal the number of files to keep.

  Read the article

• Cloning Windows 2003 Server to new hard drive results in failure

  - by Level1Coder

  Scenario: Old hdd is a Seagate 320gb SATA drive New hdd is a WD 320gb SATA drive Created an exact clone and replaced old hdd with new hdd. Boot up with new hdd, it gets into Windows 2003 server environment but things look weird. Lots of system event failures in the event viewer log. System is barely unusable, critical services are all down. Boot up with old hdd, everything is fine. QUESTION: Is it possible to do a simple clone of a Windows 2003 server system? All I'm changing is the hard drive, everything else stays the same (old CPU/old mobo/etc..)

  Read the article

• How can I re-create Microsoft Cluster Service resource groups on a different cluster?

  - by PersonalNexus

  I use Microsoft Cluster Service on a cluster of Windows Server 2003 machines containing several dozen resource groups. In the process of migrating to newer hardware, I would like move resources to the new machines on resource group at a time spread out over a few days to ease the migration and minimize risk. I was wondering of there was a smarter way to do this than manually re-creating resources on the new and then deleting them on the old cluster? The cluster has already been set up properly, the only missing is the resource groups and the resources they contain (IP, network names, services...). I have looked through the options of the cluster admin GUI and cluster.exe's commandline options, but haven't found anything like an import/export feature to copy over the configuration of a resource or entire resource group. Does something like this exist?

  Read the article

• Real-time Image Resize, Cropping and Caching Server Product

  - by Elijah

  I'm investigating what products are out there that will allow you to request images through a HTTP API in arbitrary image sizes. The server would behind a CDN but would still need to be able to handle a fair bit of traffic and be possibly load-balanced. I've been tasked with writing such a service, but I wanted to do some due diligence to see what commercial or open source solutions are out there. Google has not been particularly helpful. It may be because I have been searching for the wrong term. Third-party sites and services are out of the question because of corporate policies.

  Read the article

• How to configure Nginx to serve a variety of back-ends via multiple FCGI processes?

  - by Ben Horton

  I've seen a lot of tutorials showing one how to set up PHP/Python/Perl/RoR on nginx via various FCGI processes. None of the tutorials that I found show one how to serve multiple FCGI services off one server. How would one configure the stable nginx (nginx-0.7.64) to serve multiple FCGI processes (one for each of the above languages)? Example addresses for each FCGI process are as follows: 127.0.0.1:8080 - PHP 127.0.0.1:8081 - Python 127.0.0.1:8082 - Perl 127.0.0.1:8083 - Ruby on Rails An example configuration file that shows one how to implement multiple FCGI's off one server is really what I need. Perhaps others will benefit as well.

  Read the article

• Is Cygwin the best Unix environment for Windows? [closed]

  - by nik

  Which Unix like environment do you prefer on Windows? I have found Cygwin to be very comfortable for a Windows platform (usually XP). I am wondering if there is a better alternative (not because I want to move away from Cygwin). What are the features of Cygwin that you like OR, What are features you find in alternatives that you miss in Cygwin? I am often miss binary compatibility of applications built on Cygwin. These cannot be run directly on another Windows platform. But, usually fetching a copy of cygwin1.dll suffices. A collection of other tools, many of which work directly on the Windows subsystem rather than emulating Unix, like Cygwin does: Have been referred PowerShell a lot of times for scripting on Windows Earlier, UnixUtils was suggested more often Microsoft Windows Services for Unix

  Read the article

• Workaround for API limits [closed]

  - by blunders

  Problem: Planning on building out a client services company that requires access to APIs. Most APIs are limited based on user, IP, etc. - and even though the API calls would be on a per client basis, there's no way to get usage not tied to IPs. (Theoretical) Solution: Have each client install on their network a proxy/VPN that would allow my systems to connect and use their assigned usage. So, it's possible there's a better solution than the one I've thought of, but it's the only one I've been able to come up with.

  Read the article

• Windows Server 2008 is stuck at "configuring updates - stage 3 of 3 - 0% complete"

  - by Chris

  This has happened the last two times I've done updates to this system, and I really have no idea what is going on. It is installing a only a month's worth of updates. It only responds to ping and no services are up, so I can't view the system remotely (I have to hook up a monitor to see this message). In the past I've just restarted the system at this point and it eventually finishes updating. I want to know what I can do to avoid this situation, how to diagnose what is going on, and how to get any kind of remote access during the updates. Edit: I can start the machine in safe mode (where I did nothing but backup some files). I restarted and it no longer tries to do a windows update, just goes to the desktop where everything seems extremely broken. I can click on some things, but not launch most programs. I guess all I can do at this point is do a system restore or something.

  Read the article

• Can you have a staging and production slot in Azure Websites

  - by Barry King

  I'm looking at hosting 3 Websites (there will all use the same linked database resource but I think I have to use 3 websites within Azure for this); www.website.com, provider.website.com and admin.website.com. Using Windows Azure Websites, can you have a Staging, Production slot? I think this feature is only available to Azure Cloud Services but there is little documentation on this. If its not possible, other than spinning up 3 more sites to act as the staging sites is there another way? I want the ability to "swap" from staging to production.

  Read the article

• Run .sh (no service) file on startup

  - by MyTitle

  How to execute a script once at startup time on CentOS 6.3? I added file with following containment #chkconfig: 2345 95 20 #description: Some description sh /opt/somePath/my.sh into /etc/ini.d and it works fine (I executed required chmod, chkconfig). But my.sh file is compatible to run as service. And when I try to run in same way another .sh file (which can't to tun as service) I get exceptions on starting X. So I want to know how I can run .sh files which are not services. Thanks.

  Read the article

• Filtering attachment types in Google Apps (free Google Business)

  - by Ernest

  We have Google apps in our company for mail delivery, our business can't pay the business version yet, however, we need to control the attachment types that employees download. We recently switched from another hosting provider who recomended us to plug Google Apps for mail when we moved the domain, we had a firewall before which was able to prevent certain file types to be downloaded. I know the business version has section for filtering mail (postini services). Is there a hack around my problem? Anyone ever had this problem? Thank you! UPDATE: The main problem is gmail apps uses ssl connection, can this be changed ? how can i get the firewall to filter files only allowing *.doc, *.xls y *.pdf.

  Read the article

• What is the best method to determine an account through DNS A record configuration?

  - by Matt

  I apologize if my description of the problem is unclear. I am working for an online CMS that allows external domains to be used similar to Tumblr or Flavors.me. I noticed both of these services simply require you to add an A record to your domain's DNS. When trying this, I added an A record for a blank name and "www" both leading to my webserver's IP. While this successfully routes to my server, it doesn't retain the used domain. This leaves me without any idea of what account they're attempting to reach at the application layer. I'm using nginx as my webserver. I have changed all the nameservers for a domain before, and that works properly, however that causes complications with other issues such as mail and isn't feasible on a scaled solution. What should I be doing here? Is the A record the correct method of accomplishing this? How are sites like Tumblr and Flavors.me determining which account is being referenced by the domain?

  Read the article

• Windows Server 2008 small business server 64-Bit Vmware Server 2 IIS 7 HTTP Error 503. The service i

  - by deeztech69

  Hello, I've tried to install vmware server 2 on a small business server 2008 host and IIS 7 stopped working. Everytime I tried to access any website on the server including OWA I get HTTP Error 503. The service is unavailable. I've tried to restart the IIS services and websites with no luck. Removed vmware server and the problem persists. There are no errors in the application logs concerning IIS or anything related. I'm stumped. Does anyone have an idea what's happenning here and how to fix it?

  Read the article

• Linux server failover

  - by Lukasz

  I have two Linux servers (CentOS6) - both are identically configured connected to the same switch with a direct link between them. I only have one external IP that is assigned to eth0 on both servers (connected to the internet switch) with the interface shutdown on server 2. How can I failover to server 2 if server 1 dies - as stated they are linked directly so they can check for availability of each other via ping/tcp/udp. I toyed with Heartbeat but the documentation seems to be non-existent - not sure how to bring up an interface and start some services if the other server dies.

  Read the article

< Previous Page | 505 506 507 508 509 510 511 512 513 514 515 516  | Next Page >