Search Results

Search found 2022 results on 81 pages for 'subnet mask'.

Page 51/81 | < Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >

• Multiple Subnets on home network... would this work?

  - by rockinthesixstring

  We are looking at renting out the basement suit in our home and want to offer internet as part of the package. I however do not want the downstairs tennent to have access to our network (home office = private data). We currently have a pfsense firewall as our gateway and a Windows Server 2003 box is doing our primary DHCP (192.168.0.0/24) and DNS. Here's what I'd like to do... I'd like to setup another subnet on the DHCP server (192.168.1.0/24), and hook in another wireless router (as access point only) and address it as 192.168.1.1... from there the router will hook into our primary switch and then out through the firewall. Will Server 2003 (If I add a 192.168.1.x/24 IP to the nic) serve DHCP to the devices that connect to the new router, and will it isolate that from our network? Thanks in advance... I'm very new to multiple subnets.

  Read the article

• router propogation usng OSPF

  - by liv2hak

  I am using Juniper J-series routers to emulate a small telco and VPN customer.I need to use OSPF so that the path to each internal subnet is propogated to all PE nodes.The network topology is given below. To achieve this I am planning to run the following commands in UOW-TAU and UOW-HAM. set protocols ospf area 0.0.0.0 interface ge-0/0/0 set protocols ospf area 0.0.0.0 interface lo0.0 Do I need to do any additional configuration in TAU-PE1 and HAM-PE1 routers for it to receive the OSPF paths.? I am a beginner at the routing.Any help is appreciated.

  Read the article

• Apache2 proxypass

  - by gatsby

  i'm trying to figure out why my apache2 reverse proxy doesn't work... hope someone can clarify. i'm using an apache server as a gateway with proxy pass: 10.184.1.2 is the IP. these are PP instructions i inserted in the 000-default config file. ProxyPass / http://192.168.102.31/ ProxyPassReverse / http://192.168.102.31/ the host 192.168.102.31 is an internal IP of a subnet wich is not reachable directly by clients, but only by the apache gateway. when i try to access such a address: http://apache_gateway_name/dir i see the client trying to reach 192.168.102.31 address and of course timeout occurs. can someone help? Best regards

  Read the article

• Belking Wireless Router unable to connect to internet although wireless connection is working

  - by ptamzz

  I have a Belkin Basic N150 Wireless router. I'm trying to set up wireless connection using the wired ports my university has provided in my hostel room. Usually, when I connect my laptop using a LAN wire through the port, my settings are like IP: 10.5.130.X Subnet Mask: 255.255.254.0 Default Gateway: 10.5.130.250 DNS Server: 10.200.1.11 and I'm able to connect to the internet. Now instead of connecting my laptop directly, I've connected the lan wire to the Belkin Wireless Router, set the router as "Use as an Access Point" and in the IP field, I've put up 10.5.130.1. Now I've set the IP of my system manually to 10.5.130.3. I'm able to connect to the wi-fi but I'm still not able to connect to the internet. What am I missing?

  Read the article

• XenServer VM's lose network settings

  - by Ash

  We deploy virtual machines using Citrix XenServer 6.0 for our clients. Two seperate clients experience the same issue: when a Server 2008 virtual machine is restarted, the static IP addresses (network address, subnet, gateway, primary DNS) don't appear to apply correctly as the IP's cannot be pinged, network services cannot be accessed etc. The issue is resolved by manually switching the network adapters to DHCP, then re-setting them to the original static IP's. While not a major issue, it's a pain when restarting servers due to Windows Updates, plus iSCSI drives need to be manually connected to Windows again via iSCSI Initiator. We have tried removed the network adapters from the virtual machine under XenCentre but without luck. Anyone experienced similar issues?

  Read the article

• Using a MiFi via WDS

  - by Joril

  I have a Huawei R201 MiFi connected to the internet, and I'd like to use its internet connection even from devices that don't have WiFi, so I grabbed a wireless router I had lying around and configured WDS so that it'd connect to the MiFi, and this is working nicely (I can ping the MiFi from the router web interface). The next step was connecting my PC to the router via ethernet cable, but now I'm stuck... The PC can ping the router, but not the MiFi (they're all on the same subnet). Since the router can ping the MiFi, I guess this is some kind of routing issue? Should I get a more "flexible" router, such as one with DD-WRT maybe? Is what I'm trying to do even possible? (For the record the PC is running Lubuntu 11.10)

  Read the article

• Connect to RDS inside a VPC using Opsworks located in another VPC

  - by Consuelo Merino

  I have a RDS instance (mysql) inside a VPC called vpc-a (10.0.0.0/16). This instance is private, it can only be accessed from vpc-a. We created a stack on opsworks inside another VPC called vpc-b (10.1.0.0). We want to connect opsworks to the RDS but it doesn't work. It refuses to connect. I tried adding said subnet to the RDS security group. Also read a lot of documentation but I haven't stumbled across the answer. Any help would be greatly appreciated.

  Read the article

• How to automatically restart RRAS service after OpenVPN

  - by JT

  I have OpenVPN set up on a Windows Server 2003 box using a routed configuration. This allows users to connect and access the work LAN subnet. There are remote hosts/services however that are only accessible when used via the work network. To enable access these, I push routes out to the clients to make sure traffic to these destinations goes across the VPN, and NAT the traffic using RRAS. This all works, except: if I restart the OpenVPN service, network traffic stops working until I restart the RRAS service as well. Is there a good way for me to make the RRAS service start/restart after OpenVPN? Are service dependencies the way to go? Obviously I could write a batch file to do this, but I'd like to make the process as bullet-proof and obvious as I can so it doesn't cause problems for other admins.

  Read the article

• Linux Bridge, Samba netbios name/hostname access

  - by Christopher Wilson

  I am currently running a linux bridge in the following configuration ADSL Modem: 192.168.1.1 Linux Bridge: eth0: 192.168.1.2 eth1: no address Wireless Router: 192.168.0.1 My issue is that i cannot access the "Linux Bridge" shares using the WINS name of the server via client systems (yes i understand it is a transparent bridge but i can access it via the 192.168.1.2 address this is not on the same subnet as the client systems). This is the global section of my SMB.CONF [global] unix extensions = off os level = 20 netbios name = server guest account = nobody server string = 447 Server security = share #unix extensions = no #wins support = yes #wins server = 192.168.0.1 name resolve order = wins lmhosts hosts bcast interfaces bridge1 eth0 eth1 lo bind interfaces only = yes Can i access a bridged server using it's WINS name to access samba shares? Cheers Chris

  Read the article

• Sharing an external hard drive in Ubuntu using Samba

  - by cambraca

  /media/MYDISK is where my hard drive is mounted automatically. I created a symlink using: ln -s /media/MYDISK /home/camilo/MYDISK chmod 777 /home/camilo/MYDISK I'm setting up smb.conf like this: [myshare1] comment = external disk browsable = yes path = /home/camilo/MYDISK guest ok = yes read only = no create mask = 0775 Also, in the [global] section I tried adding the following lines: follow symlinks = yes wide links = yes unix extensions = no The problem is that when browsing the shared folder in Windows 7, I get a "\\etc\myshare1 is not accessible" error. When pointing the path to a regular folder it works fine. Also, when I point it directly to /media/MYDISK, it shows the same error. EDIT: to make it more interesting, I have no graphical interface, so I need to touch the config files directly..

  Read the article

• windows firewall and network location switch after establishing a vpn connection

  - by Konrads

  I am looking for a reasonable solution for network location switching after VPN connection is established for Windows 7. The scenario is as follows: For location public (employee plugging in his laptop in hotel, public wi-fi,etc) all inbound connections are restricted, only outbound VPN + www is enabled. Employee then initiates a VPN connection, VPN pushes routes to 10.0.0.0/8 subnet Now I would like to have lax security rules for traffic from/to 10.0.0.0/8 that comes through the VPN interface, while still protecting the laptop from traffic that comes via uplink interface as if it was private. How to achieve this switching and duality? One option I see is switching to IPSec...

  Read the article

• Local Area Connection in Slacware 13

  - by asdasd

  I have windows xp and slackware 13 on one computer, and the ISP provided me a new modem. There was manual how to configure it, so i start the web browser and typed it's ip address 192.168.1.1 and the web interface of the modem appeared so i logged in, that was easy. But under slackware, i don't know how to enter in the modem config / web interface. I type in 192.168.1.1 but it's not working. Here's the output of ifconfig eth0 : eth0 Link encap:Ethernet HWaddr 00:a1:b0:01:18:28 inet addr:169.254.73.8 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 Memory:febff400-febff4ff How can i log in into the modem from linux, i.e. find it's assigned ip under slackware ? Thank you.

  Read the article

• dd-wrt Bonjour/ netbios etc on two subnets

  - by user72182

  Hi I was wondering if any clever people out there could help me. I have a network setup with two different subnets 192.168.1.0 and 192.168.0.0 one router is connected to a VPN (via OpenVPN) the other is not. Both routers have static routes to each other and a device on one can communicate to another without issues when using IP addresses. My problem is I want to use services like Bonjour, Netbios and Apple Talk across the two networks, which currently does not work. A laptop connected on one subnet will not see a laptop connected on another. Is there anyway that you can connect the two networks together so these sort of local service will work??? I guess I have to forward the boardcast packets but I have no idea how to do this. Thanks for any help...

  Read the article

• How to tell Windows 7 to ignore a default gateway

  - by zildjohn01

  I currently have 2 network cards in my PC -- one connected to an internal network on a router with a disconnected WAN port (10.x.x.x), and one connected to the internet through a consumer router (192.168.0.x). Windows seems to recognize them correctly (my "Network and Sharing Center" lists them as "No Internet" and "Internet" respectively), however when I try browsing the internet it always tries the internal network's default gateway, rather than the one with internet access. Trying to ping a website results in "Reply from 10.0.0.1: Destination net unreachable.". A simple "route delete 0.0.0.0 mask 0.0.0.0 10.0.0.1" fixes the problems, but they return upon reboot, or upon renewing my IP. Is there any way to tell Windows to ignore one NIC's default gateway, or to at least give them priorities?

  Read the article

• CentOS: eth0 not starting on boot

  - by Cameron Aziz

  Whenever I reboot a CentOS Hyper-V VM, eth0 does not start automatically. All I need to do is perform ifup eth0 and all is fixed, but that isn't feasible from ssh! I am starting in runlevel 3. After I perform ifup eth0 on the console: [root@localhost ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:15:5D:2B:2B:07 inet addr:10.10.0.3 Bcast:10.10.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe2b:2b07/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:49 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4656 (4.5 KiB) TX bytes:6399 (6.2 KiB) Interrupt:9 Base address:0xa000 [root@localhost ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 BOOTPROTO=none IPADDR=10.10.0.3 NETMASK=255.255.255.0 GATEWAY=10.10.0.1 USERCTL=no ONBOOT=yes [root@localhost ~]# chkconfig --list | grep network network 0:off 1:off 2:on 3:on 4:on 5:on 6:off

  Read the article

• Using PowerShell, in Active Direcotry, how would I change all the DNS A records that have a given IP to a new IP?

  - by djsumdog

  We've been moving data centers and I have a lot of old records that were not correctly but in DNS as CNAME records, but A records that have a direct IP (e.g. 192.168.100.n) and they're all moving to a new subnet (10.19.100.n). I just need to write a powershell script to change all those records. I found this site: http://www.indented.co.uk/index.php/2008/12/30/administering-microsoft-dns-in-powershell/ and from it I made this simple script: $dnsServer = "meldc2" $scope = New-Object Management.ManagementScope("\\$dnsServer\root\MicrosoftDNS") $path = New-Object Management.ManagementPath("MicrosoftDNS_Zone") $options = New-Object Management.ObjectGetOptions($Null,[System.TimeSpan]::MaxValue, $True) $ZoneClass= New-Object Management.ManagementClass($scope,$path,$options) $Zones = Get-WMIObject -Computer $dnsServer -Namespace "root\MicrosoftDNS" -Class "MicrosoftDNS_Zone" $Zones | Get-Member foreach($Z in $Zones) { $Z | Select-Object Name,DsIntegrated,ZoneType,Reverse,Data } but that only gets me a listing of root zones. I don't understand how to iterate over all the entries in each of the zones. Also, all the examples I've seen involve adding new zones, but there aren't any examples I can find on modifying existing A records.

  Read the article

• Bridge and OpenVPN with shorewall

  - by Javier Martinez

  I have this scenario and everything it's working OK, but I want to configure my Shorewall and I can't do it. My interfaces are: br0 (bridge of eth0) tun0 (OpenVPN) vnet* (each one of bridged interfaces with public IP's) Public Main IP: 188.165.X.Y OpenVPN IP's: 172.28.0.x Bridge: public ip's So, I have the next configuration for shorewall: /etc/shorewall/zones #ZONE TYPE OPTIONS IN OUT # OPTIONS OPTIONS fw firewall inet ipv4 road ipv4 /etc/shorewall/interfaces #ZONE INTERFACE BROADCAST OPTIONS inet br0 detect routeback road tun+ detect routeback /etc/shorewall/policy #SOURCE DEST POLICY LOG LIMIT: CONNLIMIT: # LEVEL BURST MASK $FW all ACCEPT inet $FW DROP info road all DROP inet road DROP /etc/shorewall/tunnels #TYPE ZONE GATEWAY GATEWAY # ZONE openvpnserver:1194 inet 0.0.0.0/0 The problem is that even with shorewall running I am able to ping or connect to the virtual machines behind the bridge

  Read the article

• Windows/Samba connection error

  - by Gomibushi

  I have a Linux fileserver serving up /home for linux and windows users. I was able to connect from my windows client, but not from a DC. Then suddenly I could connect from the DC too. The linux servers run Centrify clients, and as such are part of the domain. All on same subnet. This is what the the log.smbd says, repeatedly: [2010/02/11 11:25:57, 0] lib/util_sock.c:read_data(534) read_data: read failure for 4 bytes to client 192.168.200.3. Error = Connection reset by peer On Windows it appeared as an "unknown error". EDIT: the error code is "0x80004005". We are developing a system depended on the samba share, and are worried this will appear again. It would be nice to pin point the root of this. Any ideas what this might be? Places to look?

  Read the article

• How do I force specific permissions for new files/folders on Linux file server?

  - by humble_coder

  I'm having an issue with my install of Ubuntu 9.10 (file server) and its samba permissions. Logging in and reading works fine. However, creation of new directories by users restricts access for other users. For instance, if Bob (Windows user who maps the drive) creates a folder in the directory, Jane (Mac user that simply smb mounts) can read from it, but can't write to it -- and vice versa. I then must go CHMOD 777 the directory for everyone to be happy. I've tried editing the "create/directory mask", and "force" options in the smb.conf file but this doesn't seem to help. I'm about to resort to CRONTABing a recursive chmod routine, although I'm sure this isn't the fix. How do I get all new items to always be 777? Does anyone have any suggestions to fix this ever-occurring situation? Best

  Read the article

• Correct way of bringing network interface down in linux

  - by Karolis T.

  For example: $ ifconfig dummy0 up $ ifconfig dummy0 "192.168.1.190 netmask 255.255.255.0" Calling ifconfig with no parameters shows the interface dummy0 Link encap:Ethernet HWaddr b6:1f:f3:92:6d:20 inet addr:192.168.1.190 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::b41f:f3ff:fe92:6d20/64 Scope:Link UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:1050 (1.0 KiB) How can I bring the interface down so that it doesn't show up in ifconfig ifconfig -a ifconfig dummy0 without rmmod dummy because dummy is used just for example purposes. If there is no way to do that, what "throw-away" IP could I set to it and be safe from any trouble? like $ ifconfig dummy0 down $ ifconfig dummy0 0.0.0.0

  Read the article

• Trixbox CentOS Default GW Problem (Multi-homed server)

  - by slashp

  I'm having an issue with a CentOS trixbox server which is dual-homed (one private facing NIC [eth1], one internet-facing NIC [eth0]). I can't seem to get the default gateway to set properly to our ISP's GW via eth0. I've modified the /etc/sysconfig/network to contain both a GATEWAY & GATEWAYDEV line and removed the GATEWAY line from /etc/sysconfig/network-scripts/ifcfg-eth1 (as well as /etc/sysconfig/network-scripts/ifcfg-eth0). No default GW shows up in the routing table unless it's specified in the ifcfg-eth1 file (which both the wrong interface and wrong gateway IP), otherwise, the routing table simply does not contain a default gateway..any ideas would be greatly appreciated! Thanks! EDIT Just realized when attempting to add the default gateway manually using the route add command, I receive an error stating: SIOCADDRT: Network is unreachable I know this error can occur when your default gateway and interface IP address are not on the same subnet..in this case, my public IP address of eth0 is a /29.

  Read the article

• Netboot Intel Macs without BSDP

  - by notpeter

  I have a netboot setup with DeployStudio that works great in my lab, but doesn't work on our main network. After some digging, I believe it's because our network admins are filtering BSDP (Boot Service Discovery Protocol) on our subnet at the switch level. Is it possible to hard code which server my clients (early 2007 iMac Core2Duos) should boot from without relying on BSDP? Perhaps relevant details: I do not have control over switch configs or DHCP settings. Client and server are running 10.6 Snow Leopard. The clients see the netboot server advertising itself in the 'Startup Disk' system preferences pane, but when I go to netboot it just leaves me with a flashing globe.

  Read the article

• Win 2k3 server's network problem.

  - by Sam

  I'm running 4 of Win2k3 64bit servers in the same subnet. It's been more than an year that I've running them without a problem. Recently, I kept losing the connection to one of the server. Let's say it's 'server A' which has a problem. Losing the connection means that I can't access to server A from the other servers. I've checked if server A has any internet connection problems or are there any abnomal event logs in the eventvwr - but haven't found any problems. The problem usually resolved if I restart the server again. But as time goes by, it keeps happen again and again. I can't afford to restart the server every time, and I really want to find out the reason. Can anyone help me out? Let me know if you guys need any of more information.

  Read the article

• Cannot Ping a server after configuring the Routing and Remote Access Services

  - by stacker

  After configuring the Routing and Remote Access Services to be a both VPN and NAT service, I cannot ping that server anymore from the external side. But when I configure it to be just a VPN server, or just a NAT server, I do able to ping it from the external side. My configuration is like: DC: 192.168.20.11 VPN and NUT: Nic 1: 192.168.20.1, NIC 2: 192.168.147.171 Client: 192.168.147.1 The mask is always: 255.255.255.0 I cannot understand why when configuring the VPN server to be a VPN and NAT, I cannot ping the server anymore.

  Read the article

• Configure TCP/IP to use DHCP and a Static IP Address at the Same Time

  - by Tiago

  My computer is configured to obtain a IP address automatically using DHCP. It only has one network adapter. How to configure an additional static IP address? I found a tutorial for Windows XP, but the procedure didn't work for Windows 7. Is it possible to configure two IP addresses on Windows 7, one being static e another being dynamic? How? The dynamic address I got now is 10.17.11.162. The static IP is 10.17.30.19. The network mask is the same: 255.255.224.0. Both work independently, but I don't know how to use both at the same time.

  Read the article

< Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >