Search Results

Search found 13560 results on 543 pages for 'free lancer'.

Page 511/543 | < Previous Page | 507 508 509 510 511 512 513 514 515 516 517 518  | Next Page >

  • Unmountable boot volume blue screen, what should I do?

    - by Josh
    I was trying to install an update from NVIDIA for my GTX 560, but while it was installing, my computer shut off. After a few minutes, I turned it back on. It got to the Windows boot screen and then had a blue screen error and if left on it would just keep doing that. A few details about my PC: I haven't added any new hardware or software, I'm running Windows XP Professional 32 bit and Windows XP Professional 64 bit on the same hard drive for about 2 years now. I have 2 other hard drives also, but I don't have one large enough to hold everything from my main hard drive, so formatting isn't an option. Now, as for what I've done so far: I've scanned the RAM with "memtest - 86 v3.4" and it said that it was good. I scanned the hard drive in question with chkdsk /r and it gets to 50% and tells me something along the lines of "the drive has one or more unrepairable problems". I also tried to use chkdsk on the drive I installed the new copy of Windows XP on and it got to 75% then jumped back down to 50% and stayed there (I had to reboot the pc). So, after that, I turned off auto reboot and got to read the blue screen error code and I looked it up only to find that nobody seems to have this problem, just problems close to it. The error code is 0x000000ed and I've seen a lot of these online but none that matched the detailed part of the code UNMOUNTABLE_BOOT_VOLUME 0x000000ed (0xfffffadf513c19a0, 0xffffffffc0000006, 0, 0) So, I have installed another copy of Windows XP Professional 32 bit on one of my other hard drives in hopes of accessing the data on the drive in question and when it booted it asked if I wanted chkdsk to scan the drive in question and this is what it found: file record segments 12740, 12741, 12742 and 12743 were reported unreadable. Then it says "recovering lost files" but it sits there for a few seconds and then just boots to Windows. I can't access the drive in question from Windows as far as I can tell, it just says "drive not accessible" and when I go to properties it says that the drive has 100% free space. So, after that failed I didn't give up, I looked for another way to access the drive in question. I used a Ubuntu bootable disk and was able to access the drive in question without any problems. However, I can't access the registry editor because it's a .exe file and that won't load from Ubuntu. I made a copy of the "Windows" folder and put it on one of my other drives and that's where I'm stuck at now. I'm sure my drive works fine, I know chkdsk can't fix the problem with it and I know what caused the problem in the first place for the most part, but I don't know what to do about it. I have a laptop that I can use to download and burn disks if needed and I also have the other copy of Windows XP Professional 32 bit that I can use that's installed on the computer in question (so I know it's not a hardware issue). I'm pretty sure it's a driver issue or the update was editing the registry when it shut off and left me when a broken registry. I've tried accessing C:\Windows\System32\CONFIG only to find that the Windows XP disk repair option can't even access the files on the drive in question. It seems I'll need to be able to do everything from Ubuntu unless there is something I haven't tried with the Windows XP disk. I didn't install the update on Windows XP 64 bit but yet it also has the same blue screen error (that's where the error code above came from but I haven't checked to see if they are the same). They both stopped working at the same time, so I assume it's one problem causing both to not work.

    Read the article

  • What was scientifically shown to support productivity when organizing/accessing file and folders?

    - by Tom Wijsman
    I have gathered terabytes of data but it has became a habit to store files and folders to the same folder, that folder could be kind of seen as a Inbox where most files (non-installations) enter my system. This way I end up with a big collections of files that are hard to organize properly, I mostly end up making folders that match their file type but then I still have several gigabytes of data per folder which doesn't make it efficient such that I can productively use the folder. I'd rather do a few clicks than having to search through the files, whether that's by some software product or by looking through the folder. Often the file names themselves are not proper so it would be easier to recognize them if there were few in a folder, rather than thousands of them. Scaling in the structure of directory trees in a computer cluster summarizes this problem as following: The processes of storing and retrieving information are rapidly gaining importance in science as well as society as a whole [1, 2, 3, 4]. A considerable effort is being undertaken, firstly to characterize and describe how publicly available information, for example in the world wide web, is actually organized, and secondly, to design efficient methods to access this information. [1] R. M. Shiffrin and K. B¨orner, Proc. Natl. Acad. Sci. USA 101, 5183 (2004). [2] S. Lawrence, C.L. Giles, Nature 400, 107–109 (1999). [3] R.F.I. Cancho and R.V. Sol, Proc. R. Soc. London, Ser. B 268, 2261 (2001). [4] M. Sigman and G. A. Cecchi, Proc. Natl. Acad. Sci. USA 99, 1742 (2002). It goes further on explaining how the data is usually organized by taking general looks at it, but by looking at the abstract and conclusion it doesn't come with a conclusion or approach which results in a productive organization of a directory hierarchy. So, in essence, this is a problem for which I haven't found a solution yet; and I would love to see a scientific solution to this problem. Upon searching further, I don't seem to find anything useful or free papers that approach this problem so it might be that I'm looking in the wrong place. I've also noted that there are different ways to term this problem, which leads out to different results of papers. Perhaps a paper is out there, but I'm not just using the same terms as that paper uses? They often use more scientific terms. I've once heard a story about an advocate with a laptop which has simply outperformed an advocate with had tons of papers, which shows how proper organization leads to productivity; but that story didn't share details on how the advocate used the laptop or how he had organized his data. But in any case, it was way more useful than how most of us organize our data these days... Advice me how I should organize my data, I'm not looking for suggestions here. I would love to see statistics or scientific measurement approaches that help me confirm that it does help me reach my goal.

    Read the article

  • How to transfer data between two netowks efficiently

    - by Tono Nam
    I will like to transfer files between two places over the internet. Right now I have a VPN and I am able to browse, download and transfer files. So my question is not really how to transfer the files; Instead, I will like to use the most efficient approach because the two places constantly share a lot of data. The reason why I want to get rid of the vpn is because it is two slow. Having high upload speed is very expensive/impossible on residential places so I will like to use a different approach. I was thinking about using programs such as http://www.dropbox.com . The problem with dropbox is it only enables 2 GB of storage in order for it to be free. I think the deals they offer are ok and I might be willing to pay to get that increase in speed. But I am concerned with the speed of transferring data. Dropbox will upload the file to their server then send it from the server to the other location. I will like it even faster lol. Anyways I was thinking why not create a program my self. This is the algorithm that I was thinking let me know if it sounds to crazy. (remember my goal is to transfer files as fastest as possible) Things that I will use in this algorithm: Server on the internet called S ( has fast download and upload speed. I pay to host a website and some services in there. I want to take advantage of it) Client A on location 1 Client B on location 2 So lets say on location 1 20 large files are created and need to be transferred to location 2. Client A compresses the files with the highest compression ratio possible. Client A starts sending data via UDP to client B. Because I am using UDP I will include the sequence number on each package. Have server S help speed up things. For example every time a package is lost we can use Server S to inform client A that it needs to resend a package. Anyways I think this approach will increase the transfer rate. I do not know if it is possible to start sending data meanwhile it is being compressed. Also if it is possible to start decompressing data even if we are not done receiving all the info. Maybe it will be faster to start sending the files right away without compressing. If I knew that I will always be sending large text files then I will obviously use the compression. I need this as a general algorithm. So i guess my question is should using UDP over TCP could increase performance by using an extra server to keep track of lost packages? and How should I compress files before sending? compressing a 1 GB file with the highest compression ration takes about 1 hour! I will like to take advantage of that time by sending it meanwhile it is compressed.

    Read the article

  • Postfix : relay access denied

    - by kfa
    Since I can't find a solution that works with my config, I lean on you guys to help me out with this. I've installed postfix and dovecot on a CentOS server. Everything's running well. But when I try to send an e-mail from Outlook to tld that is not .com, server returns : Relay access denied. Here's the result from the postconf -n command alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix debug_peer_level = 2 home_mailbox = Maildir/ html_directory = no inet_protocols = all mailbox_size_limit = 104857600 mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man message_size_limit = 20971520 mydestination = $myhostname, $mydomain, localhost, localhost.$mydomain newaliases_path = /usr/bin/newaliases.postfix readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES sample_directory = /usr/share/doc/postfix-2.6.6/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtp_tls_loglevel = 3 smtpd_tls_auth_only = yes smtpd_tls_cert_file = /etc/postfix/mailserver.pem smtpd_tls_key_file = /etc/postfix/mailserver.pem smtpd_tls_received_header = yes smtpd_tls_security_level = encrypt smtpd_tls_session_cache_timeout = 3600s tls_random_source = dev:/dev/urandom unknown_local_recipient_reject_code = 550 Here's the maillog error : Nov 23 13:26:24 website_name postfix/smtpd[16391]: extract_addr: input: <mrm@website_name.com> Nov 23 13:26:24 website_name postfix/smtpd[16391]: smtpd_check_addr: addr=mrm@website_name.com Nov 23 13:26:24 website_name postfix/smtpd[16391]: ctable_locate: move existing entry key mrm@website_name.com Nov 23 13:26:24 website_name postfix/smtpd[16391]: extract_addr: in: <mrm@website_name.com>, result: mrm@website_name.com Nov 23 13:26:24 website_name postfix/smtpd[16391]: fsspace: .: block size 4096, blocks free 23679665 Nov 23 13:26:24 website_name postfix/smtpd[16391]: smtpd_check_queue: blocks 4096 avail 23679665 min_free 0 msg_size_limit 20971520 Nov 23 13:26:24 website_name postfix/smtpd[16391]: > unknown[178.193.xxx.xxx]: 250 2.1.0 Ok Nov 23 13:26:24 website_name postfix/smtpd[16391]: < unknown[178.193.xxx.xxx]: RCPT TO:<[email protected]> Nov 23 13:26:24 website_name postfix/smtpd[16391]: extract_addr: input: <[email protected]> Nov 23 13:26:24 website_name postfix/smtpd[16391]: smtpd_check_addr: [email protected] Nov 23 13:26:24 website_name postfix/smtpd[16391]: ctable_locate: move existing entry key [email protected] Nov 23 13:26:24 website_name postfix/smtpd[16391]: extract_addr: in: <[email protected]>, result: [email protected] Nov 23 13:26:24 website_name postfix/smtpd[16391]: >>> START Recipient address RESTRICTIONS <<< Nov 23 13:26:24 website_name postfix/smtpd[16391]: generic_checks: name=permit_sasl_authenticated Nov 23 13:26:24 website_name postfix/smtpd[16391]: generic_checks: name=permit_sasl_authenticated status=0 Nov 23 13:26:24 website_name postfix/smtpd[16391]: generic_checks: name=reject_unauth_destination Nov 23 13:26:24 website_name postfix/smtpd[16391]: reject_unauth_destination: [email protected] Nov 23 13:26:24 website_name postfix/smtpd[16391]: permit_auth_destination: [email protected] Nov 23 13:26:24 website_name postfix/smtpd[16391]: ctable_locate: leave existing entry key [email protected] Nov 23 13:26:24 website_name postfix/smtpd[16391]: NOQUEUE: reject: RCPT from unknown[178.193.xxx.xxx]: 554 5.7.1 <[email protected]>: Relay access denied; from=<mrm@website_name.com> to=<[email protected]> proto=ESMTP helo=<[192.168.1.38]> Nov 23 13:26:24 website_name postfix/smtpd[16391]: generic_checks: name=reject_unauth_destination status=2 Nov 23 13:26:24 website_name postfix/smtpd[16391]: > unknown[178.193.xxx.xxx]: 554 5.7.1 <[email protected]>: Relay access denied Nov 23 13:26:24 website_name postfix/smtpd[16391]: smtp_get: EOF What's wrong with this? UPDATE : added to main.cf broken_sasl_auth_clients = yes smtpd_recipient_restrictions = permit_mynetworks permit_sasl_authenticated smtpd_sasl_auth_enable = yes smtpd_sasl_path = private/auth smtpd_sasl_security_options = noanonymous noplaintext smtpd_sasl_tls_security_options = $smtpd_sasl_security_options smtpd_sasl_type = dovecot UPDATE : EHLO EHLO mail.perflux.com 250-perflux.com 250-PIPELINING 250-SIZE 20971520 250-VRFY 250-ETRN 250-STARTTLS 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN

    Read the article

  • Server Admin is not allowing me to configure DNS

    - by Clinton Blackmore
    We have a Mac OS X 10.5.8 Server running DNS (and a few other services). When I connect to it (using Server Admin 10.5.3 [which comes from the Server Admin 10.5.7 tools]), and click to look at the DNS settings, all appears normal -- it shows many reverse entries and two top-level domains. However, when I select one of our domains and open the disclosure triangle, the list is empty! [There should be over a dozen entries, and the reverse entries do show up.] If I then tell it I want to add, say, an A Record to the domain, almost everything disappears -- and I am left with a list showing our two domains, one with a disclosure triangle underneath it showing a single entry, and one reverse entry to correspond to the new A record. named appears to be working fine. DNS names resolve. It appears to simply be that Server Admin is having problems with the data on the computer. No one here would have manually created a DNS entry. Now, while I think I've backed up the DNS (I backed up /var/named/, /etc/named.conf, and /etc/dns/, as mentioned here), I'm really not sure if just replacing the files would restore the DNS settings we have if things go south. I am contemplating going to settings and changing the log level from "Information" to "Debug", but 1) I am just a little concerned that it might write a bad configuration to the disk, and 2) I think it would only affect named and not Server Admin, and, so far as I can tell, named is not having a problem. (Nothing looks strange in /Library/Logs/named.log when I open it via Console/Terminal. Oddly, though, when I click on the 'log' button for DNS in Server Admin, I see no text at all, just a fully white window. When I look at one of our secondary DNS servers, I am able to see the log file through Server Admin.) This entry appears in the system log when I run Server Admin on the server: Jun 17 09:02:08 od1 Server Admin[3892]: Unexpected call to doMarkConfigurationAsDirty by 'DNS' plugin during updateConfigurationViewFromDescription It seems to occur after I've looked at DNS, look at another service, and then click back on DNS. Think that the most likely cause is a corrupt configuration file, I glanced through all the files that I backed up, and none of them is obviously gobbledygook. Here are some oddities I find when running Server Admin from a remote computer to manage the DNS. When I click to see the log file for DNS, the server starts writing messages like these to its system.log: Jun 17 09:59:04 od1 kernel[0]: Limiting open port RST response from 252 to 250 packets per second Jun 17 09:59:06 od1 kernel[0]: Limiting open port RST response from 258 to 250 packets per second This stops when I click on a different service. The inderterminate progress indicator (the spinning wheel that appears beside the "Revert" and "Save" buttons in the bottom-right corner of Server Admin) looks really strange. As far as I can tell, instead of just spinning and waiting, it is being told to start spinning repeatedly, resulting in a jerky animation. Here are some of the messages being logged on the computer running Server Admin: At startup: *** ERROR: -[GRAxes computeLayout]:1124 - plotRect height = 0.000000 <= 0.0 *** *** ERROR: -[GRChartView computeLayout]:1194 - Layout for overlay axes (0x18758f50) failed. *** (These messages don't concern me too much as they go away for a while if you delete ~/Library/Preferences/com.apple.ServerAdmin.plist). At shutdown: 2010-06-17 10:02:17.202 Server Admin[7770:10b] *** -[GroupTextField windowDidResignKey:]: unrecognized selector sent to instance 0x16e12490 More concerning are these messages: 2010-06-17 09:59:47.269 Server Admin[7770:10b] Unexpected call to doMarkConfigurationAsDirty by 'DNS' plugin during updateConfigurationViewFromDescription Server Admin(7770,0xb0453000) malloc: *** error for object 0x1c115390: double free *** set a breakpoint in malloc_error_break to debug 2010-06-17 10:01:00.795 Server Admin[7770:10b] *** -[ServiceEntry sessionHost]: unrecognized selector sent to instance 0x2af500 Any thoughts on: what the problem is how I can troubleshoot it or how to fix it? If I do need to wipe out DNS and restart, is there a good way to do this?

    Read the article

  • Issues with Verizon's "Network Extender" device talking on my home network.

    - by Logan
    I recently switched my phone service to Verizon from ATT, and I get somewhat spotty service in my house. I called them and they sent me a "network extender" device for free. Its a femtocell that connects to my home network. The directions that come with it are very dumbed down, basically just say to connect it to your router and put it near a window (so it can get a GPS signal, it has to make sure its within the correct area before operating). The problem I'm having is the network light on it stays red. The troubleshooting information that came with it tells me this means there is a bad network connection. Its connected through an ASUS router running DD-WRT. No other devices on my network have a problem with it, including a Western Digital WDLIVE device, mine and my wife's cell phones (via wifi), a Wii, and an Xbox. If I connect the device directly to my cable modem, the light goes blue (which means good) and it starts working. So this tells me that its definately a configuration issue with my router. Verizon basically washed their hands of me when I connected it to my cable modem, and told me that its a router issue and to try a different router. Because normal people just have extra routers laying around their houses... When I connect it to the router, I can watch the DHCP Clients list on the status page, and the MAC of the network extender quickly fills up the clients list, grabbing every available DHCP address. Its like it grabs an address, can't connect to the internet, releases it, grabs another, then another, then another. So in the DHCP server settings I assigned a static IP to its MAC. This made it quit doing what it was doing before, but its still not working. I found the ports I needed to open on verizon's website, and opened them in the port forwarding config on my router. This still didn't help. So, I tried setting the network extender device's IP as the DMZ IP on the router. This still did no good. I called Verizon back and got the tech to write up a report which he passed on to a "senior network tech" who I got a call back from a few hours ago. This guy told me that while an ASUS router isn't listed as a supported device, he's not really sure why its not working. He suggested restoring the firmware to stock ASUS firmware and trying again. I have a very hard time believing its DD-WRT doing this, since every other device is working just fine with it. But its also not the Network Extender, since it works just fine when connected directly to the modem. At this point I'm out of ideas, and the next step is to restore the stock firmware on my router, and then going to walmart and getting a linksys WRT-54G to try. Is there anything else I could try before going that drastic? Cliffs- -Network extender won't work behind router, works when connected directly to cable modem. -Extender goes nuts when allowed to pick its own DHCP address, I had to assign it a static IP. -Won't work when correct ports are forwarded to it -Won't work with a DMZ address.

    Read the article

  • Hide subdomain AND subdirectory using mod_rewrite?

    - by Jeremy
    I am trying to hide a subdomain and subdirectory from users. I know it may be easier to use a virtual host but will that not change direct links pointing at our site? The site currently resides at http://mail.ctrc.sk.ca/cms/ I want www.ctrc.sk.ca and ctrc.sk.ca to access this folder but still display www.ctrc.sk.ca. If that makes any sense. Here is what our current .htaccess file looks like, we are using Joomla so there already a few rules set up. Help is appreciated. # Helicon ISAPI_Rewrite configuration file # Version 3.1.0.78 ## # @version $Id: htaccess.txt 14401 2010-01-26 14:10:00Z louis $ # @package Joomla # @copyright Copyright (C) 2005 - 2010 Open Source Matters. All rights reserved. # @license http://www.gnu.org/copyleft/gpl.html GNU/GPL # Joomla! is Free Software ## ##################################################### # READ THIS COMPLETELY IF YOU CHOOSE TO USE THIS FILE # # The line just below this section: 'Options +FollowSymLinks' may cause problems # with some server configurations. It is required for use of mod_rewrite, but may already # be set by your server administrator in a way that dissallows changing it in # your .htaccess file. If using it causes your server to error out, comment it out (add # to # beginning of line), reload your site in your browser and test your sef url's. If they work, # it has been set by your server administrator and you do not need it set here. # ##################################################### ## Can be commented out if causes errors, see notes above. #Options +FollowSymLinks # # mod_rewrite in use RewriteEngine On ########## Begin - Rewrite rules to block out some common exploits ## If you experience problems on your site block out the operations listed below ## This attempts to block the most common type of exploit `attempts` to Joomla! # ## Deny access to extension xml files (uncomment out to activate) #<Files ~ "\.xml$"> #Order allow,deny #Deny from all #Satisfy all #</Files> ## End of deny access to extension xml files RewriteCond %{QUERY_STRING} mosConfig_[a-zA-Z_]{1,21}(=|\%3D) [OR] # Block out any script trying to base64_encode crap to send via URL RewriteCond %{QUERY_STRING} base64_encode.*\(.*\) [OR] # Block out any script that includes a <script> tag in URL RewriteCond %{QUERY_STRING} (\<|%3C).*script.*(\>|%3E) [NC,OR] # Block out any script trying to set a PHP GLOBALS variable via URL RewriteCond %{QUERY_STRING} GLOBALS(=|\[|\%[0-9A-Z]{0,2}) [OR] # Block out any script trying to modify a _REQUEST variable via URL RewriteCond %{QUERY_STRING} _REQUEST(=|\[|\%[0-9A-Z]{0,2}) # Send all blocked request to homepage with 403 Forbidden error! RewriteRule ^(.*)$ index.php [F,L] # ########## End - Rewrite rules to block out some common exploits # Uncomment following line if your webserver's URL # is not directly related to physical file paths. # Update Your Joomla! Directory (just / for root) #RewriteBase / ########## Begin - Joomla! core SEF Section # RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_URI} !^/index.php RewriteCond %{REQUEST_URI} (/|\.php|\.html|\.htm|\.feed|\.pdf|\.raw|/[^.]*)$ [NC] RewriteRule (.*) index.php RewriteRule .* - [E=HTTP_AUTHORIZATION:%{HTTP:Authorization},L] # ########## End - Joomla! core SEF Section EDIT Yes, mail.ctrc.sk.ca/cms/ is the root directory. Currently the DNS redirects from ctrc.sk.ca and www.ctrc.sk.ca to mail.ctrc.sk.ca/cms. However when it redirects the user still sees the mail.ctrc.sk.ca/cms/ url and I want them to only see www.ctrc.sk.ca.

    Read the article

  • How to automate org-refile for multiple todo

    - by lawlist
    I'm looking to automate org-refile so that it will find all of the matches and re-file them to a specific location (but not archive). I found a fully automated method of archiving multiple todo, and I am hopeful to find or create (with some help) something similar to this awesome function (but for a different heading / location other than archiving): https://github.com/tonyday567/jwiegley-dot-emacs/blob/master/dot-org.el (defun org-archive-done-tasks () (interactive) (save-excursion (goto-char (point-min)) (while (re-search-forward "\* \\(None\\|Someday\\) " nil t) (if (save-restriction (save-excursion (org-narrow-to-subtree) (search-forward ":LOGBOOK:" nil t))) (forward-line) (org-archive-subtree) (goto-char (line-beginning-position)))))) I also found this (written by aculich), which is a step in the right direction, but still requires repeating the function manually: http://stackoverflow.com/questions/7509463/how-to-move-a-subtree-to-another-subtree-in-org-mode-emacs ;; I also wanted a way for org-refile to refile easily to a subtree, so I wrote some code and generalized it so that it will set an arbitrary immediate target anywhere (not just in the same file). ;; Basic usage is to move somewhere in Tree B and type C-c C-x C-m to mark the target for refiling, then move to the entry in Tree A that you want to refile and type C-c C-w which will immediately refile into the target location you set in Tree B without prompting you, unless you called org-refile-immediate-target with a prefix arg C-u C-c C-x C-m. ;; Note that if you press C-c C-w in rapid succession to refile multiple entries it will preserve the order of your entries even if org-reverse-note-order is set to t, but you can turn it off to respect the setting of org-reverse-note-order with a double prefix arg C-u C-u C-c C-x C-m. (defvar org-refile-immediate nil "Refile immediately using `org-refile-immediate-target' instead of prompting.") (make-local-variable 'org-refile-immediate) (defvar org-refile-immediate-preserve-order t "If last command was also `org-refile' then preserve ordering.") (make-local-variable 'org-refile-immediate-preserve-order) (defvar org-refile-immediate-target nil) "Value uses the same format as an item in `org-refile-targets'." (make-local-variable 'org-refile-immediate-target) (defadvice org-refile (around org-immediate activate) (if (not org-refile-immediate) ad-do-it ;; if last command was `org-refile' then preserve ordering (let ((org-reverse-note-order (if (and org-refile-immediate-preserve-order (eq last-command 'org-refile)) nil org-reverse-note-order))) (ad-set-arg 2 (assoc org-refile-immediate-target (org-refile-get-targets))) (prog1 ad-do-it (setq this-command 'org-refile))))) (defadvice org-refile-cache-clear (after org-refile-history-clear activate) (setq org-refile-targets (default-value 'org-refile-targets)) (setq org-refile-immediate nil) (setq org-refile-immediate-target nil) (setq org-refile-history nil)) ;;;###autoload (defun org-refile-immediate-target (&optional arg) "Set current entry as `org-refile' target. Non-nil turns off `org-refile-immediate', otherwise `org-refile' will immediately refile without prompting for target using most recent entry in `org-refile-targets' that matches `org-refile-immediate-target' as the default." (interactive "P") (if (equal arg '(16)) (progn (setq org-refile-immediate-preserve-order (not org-refile-immediate-preserve-order)) (message "Order preserving is turned: %s" (if org-refile-immediate-preserve-order "on" "off"))) (setq org-refile-immediate (unless arg t)) (make-local-variable 'org-refile-targets) (let* ((components (org-heading-components)) (level (first components)) (heading (nth 4 components)) (string (substring-no-properties heading))) (add-to-list 'org-refile-targets (append (list (buffer-file-name)) (cons :regexp (format "^%s %s$" (make-string level ?*) string)))) (setq org-refile-immediate-target heading)))) (define-key org-mode-map "\C-c\C-x\C-m" 'org-refile-immediate-target) It sure would be helpful if aculich, or some other maven, could please create a variable similar to (setq org-archive-location "~/0.todo.org::* Archived Tasks") so users can specify the file and heading, which is already a part of the org-archive-subtree functionality. I'm doing a search and mark because I don't have the wherewithal to create something like org-archive-location for this setup. EDIT: One step closer -- almost home free . . . (defun lawlist-auto-refile () (interactive) (beginning-of-buffer) (re-search-forward "\* UNDATED") (org-refile-immediate-target) ;; cursor must be on a heading to work. (save-excursion (re-search-backward "\* UNDATED") ;; must be written in such a way so that sub-entries of * UNDATED are not searched; or else infinity loop. (while (re-search-backward "\* \\(None\\|Someday\\) " nil t) (org-refile) ) ) )

    Read the article

  • Moving users folder on Windows-7 to another partition - bad idea?

    - by Donat
    Hi, I'd like to re-submit here a question posted by Benjol on Aug 17at 5:57 "Moving users folder on Windows Vista to another partition - bad idea?" (I can't post one than one link until I earn "10 reputation" and removed my "answer" there to post my follow-up questions here). I am anxiously getting ready at long last to to carry out a clean install (using custom install option) from Vista to Windows-7 Home Premium 64bit with the free upgrade I received late October. For my Vista system I successfully set-up last Summer a multi-partitions scheme with Users and Program Data on a a different partition than the operating system (see link below, and its subsequent links in my comment for details). http://tuts4tech.net/2009/08/05/windows-7-move-the-users-and-program-files-directories-to-a-different-partition/comment-page-1/#comment-562 I was planning a similar set-up for windows 7, a little more streamlined, with OS, Program Files on C:, Users and Program Data on D:, and TV media recording on a separate partition. Reading the Question submitted by Benjol, I am second guessing too. Is moving Users and Program Data on a different partition than the default primary partition with OS and Program Files such a good idea? The couple of people I talked to at the official Microsoft Windows 7 booth at CES 2010 gave the same answer to the intention of moving the Users profile folder to another partition. In a nutshell, they all told me that they used to do this in XP and less in Vista but not anymore with Windows 7... "It is stable, after two months still no problem" I had the feeling it was a scripted answer to emphasize how Windows 7 is so stable and efficient... (Will Windows-7 system not become bugged down over the course of several months to a year or two? Only time will tell) Long story short, I share the same view than Benjol expressed with respect to being "able to backup and restore system and user data independently." I just received a 2TB usb2, eSATA external hard drive as a back-up drive, which includes NTI Shadow 4 (4.1.0.150) for back-up solution. I took note of the issue with NTUSER.DAT and I will read more about Volume Shadow Copy Service (VSS) for Windows 7. I am willing to put the effort if placing Users and Program Data on a different partition would allow to restore a fresher OS+Program image when the system gets bugged down. Questions: Is it such a bad idea? What is the "easy route" referred by Benjol in his post? Is it to just relocate folders to another partition using the Folder property tool? (It is not practical for several users and might not provide a straightforward restore process of just OS and Program Files when needed.) I am starting to learn about Windows 7 libraries. Would Windows 7 libraries be another alternative to achieve this? All this reading to decide how to organize the partition scheme for my custom system is starting to be confusing. I apologize for this lengthy Question. It is my first day here on SuperUser and I am just learning how different from a discussion thread it is. Thank you in advance for all your suggestions and comments. Donat

    Read the article

  • Choice of an OS for a home ZFS NAS

    - by OlafM
    I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post.

    Read the article

  • Cheapest way to connect 20-24 Sata II HDDs in a budget storage server?

    - by Joe Hopfgartner
    I need to assemble a high density storage server for as cheap as possible. It's been a while for me and the last systems I integrated didn't even have Sata yet... During my Research I of course stumbled about Nexsan SATA Beast, the BackBlaze storage Pods as well as some ridiculously overpriced HP Proliant or Dell storage solutions. Finally I choose Norco cases as the way to go. My eye is set on the RPC-4020, which is a 4U 19" Rackmount case with 20 Hot Swap 3.5" SATA/SAS Hdd trays (Backplanes included) and room for two 2.5" OS drives as well as a Slim Line CD-Rom. The backplanes connect with a single SATA port for each drive, so there are 20 internal SATA ports to to be connected. They also have redundant power ports which I think is quite nice. The cheapest price I have found is 290$ + 40$ shipping. In europe the cheapest unfortunately is 370€ (500$) + 40 € shipping... A nice alternative would be the RPC-4224 which has SFF-8087 Mini SAS connectors that bundle 4 SATA trays each. But it doesn't seem to be available in Europe (where i am) anywhere. So here comes my problem: What Mainboard/Controller to choose to connect them for as cheap as possible while still having nice data rates? I have to say that the server is intended as a Storage server with 1gps connectivity and the data transfer will be distributed very evenly across all drives. I also don't require any raid functionality. This is all done at application level, I just need JBOD. So for example if I go for the RPC 4020 Model I need to connect 20 Storage + 1 OS + 1 CDROM Sata ports. I searched a bit and stumbled across this very low priced controller: http://www.intel.com/products/server/raid-controllers/SASWT4I/SASWT4I-overview.htm They sell it for 115 € here and the specs say it can control up to 122 hard discs and has 4 Mini SAS connectors. So I would use 4 Mini SAS 36pin - 4 SATA 7pin cables to connect 4 SATA drives to each port and choose a Mainboard taht has 6 SATA on board (for example this one) and hurray, I can connect my 22 SATA devices for as low as about ~ 220 EUR (cpu, ram, psu, case not counted) Question: WOULD THAT WORK? And if not, why? 2nd Question: If I go for the 4220 or 4224 Model, I have internal Mini SAS connectors. Am I right in assuming that the backplane than acts as a "SAS Expander"? And can I just plug these SAS connectors into any SAS port I can find on my controller / mainboard or are there certain requirements? I know that SATA port multipliers only work with controllers that are ready for that. But isn't this expansion already implemented in the SAS standard? I am sorry that this is a very broad question, but I really spent the last week reading up and it seems to be not so clear! Especially all the controlling hardware specifications! 3rd Question: A lot of hardware specs feature "internal channels" and "internal connectors". The connecors are the physical numbers of places where I can plug a cable in. I got that. But are the "internal channels" always the maximum numbers of physical drives that can be used in the end? Or can I enhance this further by Expanders/Fanouts? 4th and last question: What do you think about the setup so far? Do you know any good alternatives? Maby I am completely going the wrong way and some DAS would be way better? Are there any comparable chassis available in europe? Please feel free to say whatever you think is relevant to the subject!

    Read the article

  • Exchange 2003-Exchange 2010 post migration GAL/OAB problem

    - by user68726
    I am very new to Exchange so forgive my newbie-ness. I've exhausted Google trying to find a way to solve my problem so I'm hoping some of you gurus can shed some light on my next steps. Please forgive my bungling around through this. The problem I cannot download/update the Global Address List (GAL) and Offline Address Book (OAB) on my Outlook 2010 clients. I get: Task 'emailaddress' reported error (0x8004010F) : 'The operation failed. An object cannot be found.' ---- error. I'm using cached exchange mode, which if I turn off Outlook hangs completely from the moment I start it up. (Note I've replaced my actual email address with 'emailaddress') Background information I migrated mailboxes, public store, etc. from a Small Business Server 2003 with Exchange 2003 box to a Server 2008 R2 with Exchange 2010 based primarily on an experts exchange how to article. The exchange server is up and running as an internet facing exchange server with all of the roles necessary to send and receive mail and in that capacity is working fine. I "thought" I had successfully migrated everything from the SBS03 box, and due to huge amounts of errors in everything from AD to the Exchange install itself I removed the reference to the SBS03 server in adsiedit. I've still got access to the old SBS03 box, but as I said the number of errors in everything is preventing even the uninstall of Exchange (or the starting of the Exchange Information Store service), so I'm quite content to leave that box completely out of the picture while trying to solve my problem. After research I discovered this is most likely because I failed to run the “update-globaladdresslist” (or get / update) command from the Exchange shell before I removed the Exchange 2003 server from adsiedit (and the network). If I run the command now it gives me: WARNING: The recipient "domainname.com/Microsoft Exchange System Objects/Offline Address Book - first administrative group" is invalid and couldn't be updated. WARNING: The recipient "domainname.com/Microsoft Exchange System Objects/Schedule+ Free Busy Information – first administrative group" is invalid and couldn't be updated. WARNING: The recipient "domainname.com/Microsoft Exchange System Objects/ContainernameArchive" is invalid and couldn't be updated. WARNING: The recipient "domainname.com/Microsoft Exchange System Objects/ContainernameContacts" is invalid and couldn't be updated. (Note that I’ve replaced my domain with “domainname.com” and my organization name with “containername”) What I’ve tried I don’t want to use the old OAB, or GAL, I don’t care about either, our GAL and distribution lists needed to be organized anyway, so at this point I really just want to get rid of the old reference to the “first administrative group” and move on. I’ve tried to create a new GAL and tell Exchange 2010 to use that GAL instead of the old GAL, but I'm obviously missing some of the commands or something dumb I need to do to start over with a blank slate/GAL/OAB. I'm very tempted to completely delete the entire "first administrative group" tree from adsiedit and see if that gets rid of the ridiculous reference that no longer exists but I dont want to break something else. Commands run to try to create a new GAL and tell exch10 to use that GAL: New-globaladdresslist –name NAMEOFNEWGAL Set-globaladdresslist GUID –name NAMEOFNEWGAL This did nothing for me except now when I run get-globaladdresslist or with the | FL pipe I see two GALs listed, the “default global address list” and the “NAMEOFNEWGAL” that I created. After a little more research this morning it looks like you can't change/delete/remove the default address list, and the only way to do what I'm trying to do would be to maybe remove the default address list via adsiedit and recreate with a command something like new-GlobalAddressList -Name "Default Global Address List" -IncludedRecipients AllRecipients. This would be acceptable but I've searched and searched and can't find instructions or a breakdown of where exactly the default GAL lives in AD, and if I'd have to remove multiple child references/records. Of interest I'm getting an event ID 9337 in my application log OALGen did not find any recipients in address list \Global Address List. This offline address list will not be generated. -\NAMEOFMYOAB --------- on my Exchange 2010 box, which pretty much to me seems to confirm my suspicion that the empty GAL/OAB is what's causing the Outlook client 0x8004010F error. Help please!

    Read the article

  • Intermittent lockups, unable to diagnose in over a year

    - by Magsol
    Here's a real doosie; I may just give my firstborn child to whomever helps me solve this problem. In July 2008, I assembled what would be my desktop computer for graduate school. Here are the specs of the machine I built: Thermaltake 750W PSU Corsair Dominator 2x2GB 240-pin SDRAM Thermaltake Tower Asus P5K Deluxe Motherboard Intel Core 2 Quad Q9300 2.5GHz CPU 2 x GeForce 8600 GT WD Caviar Blue 640GB hard drive CD burner DVD burner Soon thereafter, I ordered a new motherboard (because I was an idiot; that first motherboard supported CrossFire, not SLI), an Asus P5N-D. I was originally running Windows XP SP3. Pretty much right into the start of the fall semester, my desktop would simply lock up after awhile. If my system was largely idling, it would be after 1-3 days. If was gaming, it often happened an hour or two into my gaming session, indicating a link to activity level. Here's where it started getting interesting. I started looking at the system temps. The CPU was warmer than it should have been (~60s C), so I purchased some more efficient cooling compound a way better cooler for it. Now it hardly goes over 40 C. Intel was even kind enough to swap it out for free, just to rule it out. Lockups continued. The graphics cards were also running pretty warm: about 60 C idling. Removing one of them seemed to improve stability a little bit...as in, it wouldn't lock up quite as frequently, but still always eventually locked up. But it didn't matter which card I used or removed, the lockups continued. I reverted back to the original motherboard, the P5K Deluxe. Lockups continued. I purchased an entirely new motherboard, eVGA's nForce 750i. Lockups continued. Ran memtest86+ over and over and over, with no errors. Even RMA'd the memory. Lockups continued. Replaced the PSU with a Corsair 750W PSU. Lockups continued. Tried disconnecting all IDE drives (HDDs are SATA). Lockups continued. Replaced both graphics cards with a single Radeon HD 4980. Average temps are now always around 50 C when idling, 60 C only when gaming. Lockups continued. Throughout the whole ordeal, the system has been upgraded from Windows XP SP3 to Vista 32-bit, to Vista 64-bit, and is now at Windows 7 64-bit. Lockups have occurred at every step along the way (each OS was in place for at least a few months before the next upgrade). Edit: By "upgrade" I mean clean install each time. In addition to those reformats, I have performed many, many other reformats of the system and a reinstall of whatever OS had been previously installed in an attempt to rectify this problem, to no avail./Edit When the system locks up, there's no blue screen, no reboot, no error message of any kind. It simply freezes in place until I hit the reset button. Very, very rarely, once Windows boots back up, the system informs me that Windows has recovered from an error, but it can never find the source aside from some piece of hardware. I've swapped out every component in this computer, and there are more fans in it than I care to count...though for the sake of completeness: top 80mm case fan (out) rear 80mm case fan (out) rear 120mm case fan (out) front 120mm case fan (in) side 250mm case fan (in) giant CPU fan on-board motherboard fan (the eVGA board) triple-fan memory setup (came with the memory) PSU internal fan another 120mm fan I stuck on the underside of the video card to keep hot air from collecting at the bottom of the case I'm truly out of ideas. ANY help at all would be oh-so-very GREATLY appreciated. Thank you!

    Read the article

  • Choice and setup of version control

    - by Peter M
    I am about to set up an new laptop and in the process transition to a new version control system as part of a general cleanup. Currently I use a centralized version control system (yes it is VSS, and yes I know all the pro's and con's of that system, but as a single user system it works well for me). I have very little requirements for a new system and I am free to choose among any of the current mainstream players, but cost constraints will push me towards oss. Some of my requirements are: Runs on a single machine (ie the laptop in question) under windows I am not sharing things with other developers or workers - this is more for my own historical benefits. I want to version source code, documentation and binary files I have a large hierarchy of projects that are unrelated (see below) I have files within the hierarchy that don't need to be controlled (but could be) Some projects use Visual Studio, so some integration there could be nice. There could be some sharing of files between jobs. I generally only need a small about of branching in code files The directory hierarchy that I have at the moment is somewhat like: Root | |--Customer #1 | | | |--Job #1 | | | | | |--Data files received from Customer for Job (not controlled) | | |--Documentation files (controlled) | | |--Project information files (not controlled - but could be) | | |--Software Project Files (controlled) | | |--Scratch dir for job (not controlled) | | | |--Job #2 | | (same structure as above) | |--Customer #2 | |.. | |--Cusmtomer #n |.. Currently I have about 22 customers with differing numbers of projects underneath them. At the moment I have a single VSS repository based at the root of the directory structure. If I kept with a centralized system (ie SVN) I believe that I should keep the same approach and continue with a single repository based from the root dir. Is this a valid approach? However if I move to a distributed tool then I am unsure of how I should handle the situation. My initial guess is that I should not have a repository based on the root of my entire directory structure - but that is a guess so I really don't know how valid it is. Should I pitch a distributed approach at the Root, Customer, Job or sub-Job directory level? Also what I am not clear on with distributed tools (and perhaps with SVN as well), is if I can branch parts of a repository. For example, I can see branching source code in software projects as being useful, but branching my documentation as not being useful. So if I pitch a repository at the Job level, can I just branch the Software Project Files? Or would all files in that Job be branched? Every time I look at distributed tools I get a nagging feeling that they are not suited to my style of setup. I am uncomfortable with idea of having to manually set up something like 50 to 80 separate repositories (if I pitch at the Job level, or 20+ if at the Customer level) within my directory hierarchy. This feeling also extends to having all those repositories scattered around as well - however I do have a backup strategy that I trust, so this latter feeling is pretty well unfounded. So what advice can you all give me? Thanks in advance!

    Read the article

  • Server Cabinet/Room Cooling

    - by user37226
    Hello all. I currently have two desktops and three servers in my office sitting on the floor (I know this is bad). With that many servers the ambient temperature in the room goes up quickly. I am located in Dallas, TX so during the winter, if the heat is kept low, it is not a problem, but during the summer it easily jumps the room +10 degrees. I have decided and found a free 42U server cabinet that a hosting company was throwing away to house all of these systems in. One server is in a rack mount case while the other four servers are housed in mid-tower cases. I have purchased shelves for each computer and plan to lay the towers side ways on these shelves (as replacing the cases costs a heck of a lot of money). I like the idea of housing all of these systems in the cabinet because it will save a lot of room and clean up all of the cabling currently laying all over the office floor. When putting this setup together over the next couple of weeks, I want to address issues with dust and cooling. The server cabinet has a fan on top, front plexiglass door and a rear metal door with vent wholes on the bottom. First the cooling issues. I know I am going to want to have cool air enter the bottom of the cabinet and exit the top. I do not want the room heating up though as this will make my work area hot and then make the servers warmer as the air eventually reenters the cabinet. I had an idea to fix this problem, but am unsure if it will work. I was thinking of taking flexible piping and adapting it to the back fans of the computer having the other end of the pipe at the top close to the cabinet's top mounted fan. I was then thinking of creating a duct around the top fan into the attic. Now I am very concerned that the attic will cause issues with this type of setup because during July/August time frame, the attic is easily 120 degrees F. I could also use the flexible pipe to take it to an attic exhaust vent if it would be better to vent it into the 100 degree air outside (at least there may be wind. The other option would be to buy a small portable air conditioner. This may be a possibility, but do I want to spend the extra money on power? I bet this increases the noise. Plus they are around $250 on Amazon. What would you all recommend? Depending on the solution I end up running with above, I would also like to limit the dust that gets into the cabinet. If I were to cut a whole and mount a second cabinet fan on the bottom of the rear door, could I possibly mount a standard home air filter on the other side of that whole? Thanks in advance for your recommendations. I look forward to reading your interesting ideas.

    Read the article

  • Server Cabinet/Room Cooling

    - by user37226
    Hello all. I currently have two desktops and three servers in my office sitting on the floor (I know this is bad). With that many servers the ambient temperature in the room goes up quickly. I am located in Dallas, TX so during the winter, if the heat is kept low, it is not a problem, but during the summer it easily jumps the room +10 degrees. I have decided and found a free 42U server cabinet that a hosting company was throwing away to house all of these systems in. One server is in a rack mount case while the other four servers are housed in mid-tower cases. I have purchased shelves for each computer and plan to lay the towers side ways on these shelves (as replacing the cases costs a heck of a lot of money). I like the idea of housing all of these systems in the cabinet because it will save a lot of room and clean up all of the cabling currently laying all over the office floor. When putting this setup together over the next couple of weeks, I want to address issues with dust and cooling. The server cabinet has a fan on top, front plexiglass door and a rear metal door with vent wholes on the bottom. First the cooling issues. I know I am going to want to have cool air enter the bottom of the cabinet and exit the top. I do not want the room heating up though as this will make my work area hot and then make the servers warmer as the air eventually reenters the cabinet. I had an idea to fix this problem, but am unsure if it will work. I was thinking of taking flexible piping and adapting it to the back fans of the computer having the other end of the pipe at the top close to the cabinet's top mounted fan. I was then thinking of creating a duct around the top fan into the attic. Now I am very concerned that the attic will cause issues with this type of setup because during July/August time frame, the attic is easily 120 degrees F. I could also use the flexible pipe to take it to an attic exhaust vent if it would be better to vent it into the 100 degree air outside (at least there may be wind. The other option would be to buy a small portable air conditioner. This may be a possibility, but do I want to spend the extra money on power? I bet this increases the noise. Plus they are around $250 on Amazon. What would you all recommend? Depending on the solution I end up running with above, I would also like to limit the dust that gets into the cabinet. If I were to cut a whole and mount a second cabinet fan on the bottom of the rear door, could I possibly mount a standard home air filter on the other side of that whole? Thanks in advance for your recommendations. I look forward to reading your interesting ideas.

    Read the article

  • Router 2wire, Slackware desktop in DMZ mode, iptables policy aginst ping, but still pingable

    - by user135501
    I'm in DMZ mode, so I'm firewalling myself, stealthy all ok, but I get faulty test results from Shields Up that there are pings. Yesterday I couldn't make a connection to game servers work, because ping block was enabled (on the router). I disabled it, but this persists even due to my firewall. What is the connection between me and my router in DMZ mode (for my machine, there is bunch of others too behind router firewall)? When it allows router affecting if I'm pingable or not and if router has setting not blocking ping, rules in my iptables for this scenario do not work. Please ignore commented rules, I do uncomment them as I want. These two should do the job right? iptables -A INPUT -p icmp --icmp-type echo-request -j DROP echo 1 > /proc/sys/net/ipv4/icmp_echo_ignore_all Here are my iptables: #!/bin/sh # Begin /bin/firewall-start # Insert connection-tracking modules (not needed if built into the kernel). #modprobe ip_tables #modprobe iptable_filter #modprobe ip_conntrack #modprobe ip_conntrack_ftp #modprobe ipt_state #modprobe ipt_LOG # allow local-only connections iptables -A INPUT -i lo -j ACCEPT # free output on any interface to any ip for any service # (equal to -P ACCEPT) iptables -A OUTPUT -j ACCEPT # permit answers on already established connections # and permit new connections related to established ones (eg active-ftp) iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT #Gamespy&NWN #iptables -A INPUT -p tcp -m tcp -m multiport --ports 5120:5129 -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 6667 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 28910 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29900 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29901 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29920 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p udp -m udp -m multiport --ports 5120:5129 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 6500 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 27900 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 27901 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 29910 -j ACCEPT # Log everything else: What's Windows' latest exploitable vulnerability? iptables -A INPUT -j LOG --log-prefix "FIREWALL:INPUT" # set a sane policy: everything not accepted > /dev/null iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT DROP iptables -A INPUT -p icmp --icmp-type echo-request -j DROP # be verbose on dynamic ip-addresses (not needed in case of static IP) echo 2 > /proc/sys/net/ipv4/ip_dynaddr # disable ExplicitCongestionNotification - too many routers are still # ignorant echo 0 > /proc/sys/net/ipv4/tcp_ecn #ping death echo 1 > /proc/sys/net/ipv4/icmp_echo_ignore_all # If you are frequently accessing ftp-servers or enjoy chatting you might # notice certain delays because some implementations of these daemons have # the feature of querying an identd on your box for your username for # logging. Although there's really no harm in this, having an identd # running is not recommended because some implementations are known to be # vulnerable. # To avoid these delays you could reject the requests with a 'tcp-reset': #iptables -A INPUT -p tcp --dport 113 -j REJECT --reject-with tcp-reset #iptables -A OUTPUT -p tcp --sport 113 -m state --state RELATED -j ACCEPT # To log and drop invalid packets, mostly harmless packets that came in # after netfilter's timeout, sometimes scans: #iptables -I INPUT 1 -p tcp -m state --state INVALID -j LOG --log-prefix \ "FIREWALL:INVALID" #iptables -I INPUT 2 -p tcp -m state --state INVALID -j DROP # End /bin/firewall-start

    Read the article

  • PC runs very slowly for no apparent reason

    - by GalacticCowboy
    I have a Dell Latitude D820 that I've owned for about 2.5 years. It is a Core 2 Duo T7200 2.0GHz, with 2 GB of RAM, an 80 GB hard drive and an NVidia Quadro 120M video card. The computer was purchased in late November of 2006 with XP Pro, and included a free upgrade to Vista Business. (Vista was available on MSDN but not yet via retail, so the Vista Business upgrades weren't shipped until March of '07.) Since we had an MSDN subscription at the time, I installed Vista Ultimate on it pretty much as soon as I got it. It ran happily until sometime in the spring of 2007 when Media Center (which I had never used except to watch DVDs) started throwing some kind of bizarre SQL (CE?) error. This error would pop up at random times just while using the computer. Furthermore, Media Center would no longer start. I never identified the cause of this error. I had the Vista Business upgrade by this time, so I nuked the machine, installed XP and all the drivers, and then the Vista Business upgrade. Again, it ran happily for a few months and then started behaving badly once again. Vista Business doesn't have Media Center, so this exhibited completely unrelated symptoms. For no apparent reason and at fairly random times, the machine would suddenly appear to freeze up or run very slowly. For example, launching a new application window (any app) might take 30-45 seconds to paint fully. However, Task Manager showed very low CPU load, memory, etc. I tried all the normal stuff (chkdsk, defrag, etc.) and ran several diagnostic programs to try to identify any problems, but none found anything. It eventually reached the point that the computer was all but unusable, so I nuked it again and installed XP. This time I decided to stick with XP instead of going to Vista. However, within the past couple of months it has started to exhibit the same symptoms in XP that I used to see in Vista. The computer is still under Dell warranty until December, but so far they aren't any help unless I can identify a specific problem. A friend (partner in a now-dead business) has an identical machine that was purchased at the same time. His machine exhibits none of these symptoms, which leads me to believe it is a hardware issue, but I can't figure out how to identify it. Any ideas? Utilities? Seen something similar? At this point I can't even identify any pattern to the behavior, but would be willing to run a "stress test"-style app for as long as a couple days if I had any hope that it would find something. EDIT July 17 I'm testing jerryjvl's answer regarding the video card, though I'm not sure it fully explains the symptoms yet. This morning I ran a video stress test. The test itself ran fine, but immediately afterward the PC started acting up again. I left ProcExp open and various system processes were consuming 50-60% of the CPU but with no apparent reason. For example, "services.exe" was eating about 40%, but the sum of its child processes wasn't higher than about 5%. I left it alone for several minutes to settle down, and then it was fine again. I used the "video card stability test" from firestone-group.com. Its output isn't very detailed, but it at least exercises the hardware pretty hard. EDIT July 22 Thanks for your excellent suggestions. Here is an update on what I have tried so far. Ran memtest86, SeaTools (Seagate), Hitachi drive fitness test, video card stability test (mentioned above). The video card test was the only one that seemed to produce any results, though it didn't occur during the actual test. I defragged the drive (again...) with JkDefrag I dropped the video card

    Read the article

  • Can I make my drives visible and change their partition type without losing my data?

    - by user165408
    I have made a lot of mistakes and now I cannot see my hard disk nor I can start my operating system on my laptop. All my passwords and important files on my hdd without any backup. I followed this course of action Changed my hard disk partitions to dynamic just for getting 5th partition. (1st mistake) Decreased partitions to 4 again. Backed up operating system from 4th to 3rd partition with Norton Ghost. Booted from a live CD for Windows XP. Formatted 4th partition and moved my all important data from 1st and 2nd partitions to the 4th partition. Deleted 1st and 2nd partitions and got 1 partition from half of empty space. So I have just 3 partitions and empty space between 1st and 2nd partitions. Tried to install Windows 8 to the first partition but it did not allow because it is dynamic. Also it did not allow to install to other partitions. Tried to install Windows XP to the 1st partition but it said if I continue I cannot use other drivers. Therefore I escaped from installing it. Booted from the Windows XP live CD then increased 1st partiton to less than 400mb of empty space. Therefore I thought it will be adjacent but it was shown as 2 partitions. In my computer I see just 3 drivers. Using Norton Ghost I recovered my OS to the 1st partition. (2nd mistake it was on 4th partition originally) Booted from a Windows XP live CD I tried to install bcdedit to the Windows XP live CD but it did not work. Then I tried to install EaseUS Partition Master Home Edition. It was installed with errors then I start it and it showed me an error like there is no hard disk. I looked to my PC and my drivers were not there. Booted from the Norton Ghost CD and it did not show me my drivers either, but before I was able to see them. I checked numbers of partition shown by the Norton Ghost utility and they are still have same numbers so I have to see my drivers but I cannot see them now. My hard disk is shown as extarnal dynamic now so I cannot see any drive in my PC in the live Windows XP. There are two options; first one is import extarnal disk and second one is convert disk to basic. Will they delete my data? I fear booting from CDs like Windows XP live CD, Norton Ghost CD, and the operating system CD/DVD, because they may overwrite a few MB their data to my data. These recover tools are already exist in Windows XP live CD by The Ultimate Boot CD for Windows. Can any of them help me? CompuAppa SwissKnife V3 DBXtract Disk Investigator Fab's AutoBackup 2.0 FileRecovery Floppy Repair Free Undelete Handy Recovery Recovery Manager Restorastion Restorastion Help File by UBCD4Win UnChk Unstoppable Copier Finally How can I make it so that my drives are visible again without losing my data? How can I convert my dynamic partitions to basic without losing my data?

    Read the article

  • Specifying a Postfix Instance to send outbound email

    - by Catherine Jefferson
    I have a CentOS 6.5 server running Postfix 2.6x (the default distribution) with five public IPv4 IPs bound to it. Each IP has DNS and rDNS set separately. Each uses a different hostname at a different domain. I have five Postfix instances, one bound to each IP, like this example: 192.168.34.104 red.example.com /etc/postfix 192.168.36.48 green.example.net /etc/postfix-green 192.168.36.49 pink.example.org /etc/postfix-pink 192.168.36.50 orange.example.info /etc/postfix-orange 192.168.36.51 blue.example.us /etc/postfix-blue I've tested each IP by telneting to port 25. Postfix answers and banners properly with the correct hostname. Email is received on all of these instances with no problems and is routed to the correct place. This setup, minus the final instance, has existed for a couple of years and works. I never bothered to set up outbound email to go through any but the main instance, however; there was no need. Now I need to send email from blue.example.us that actually leaves from that interface and IP, such that the Received headers show blue.example.us as the sending mailhost, so that SPF and DKIM validate, etc etc. The email that will be sent from blue.example.com is a feedback loop sent by a single shell account on the server (account5), an account that is dedicated to sending this email. The account receives the feedback loop emails from servers on other networks, saves the bodies of those emails, and then generates a new outbound email header, appends the saved body, and sends the email. It's sending by piping each email to sendmail -oi -t. We're doing it this way to mask the identities of the initial servers. The procmail script that processes these emails works correctly. However, I cannot configure this account to send email through the proper Postfix instance/IP/interface. The exact same account and script sends email through the main Postfix instance /etc/postfix without any issues. When I change MAIL_CONFIG to point to /etc/postfix-blue in either .bash_profile or the Procmail script that handles this email, though, I get this error: sendmail: fatal: User account5(###) is not allowed to submit mail I've read the manuals on Postfix.org, searched Google, and tried the suggestions in three previous answers here on ServerFault.com: Postfix - specify interface to deliver outbound mail on Postfix user is not allowed to submit mail Postfix rejects php mails I have been careful to stop and restart Postfix after each configuration change, and tested the results. Nothing has worked. The main postfix instance happily accepts outbound email from account5. The postfix-blue instance continues to reject email from account5 with the sendmail error above. As tempting as it is to blame machine hostility, I know that I must be missing something or doing something wrong. Does anybody have any suggestions as to what it might be? Please feel free to ask for further information about my setup if you need it. =-=-=-=-=-=-=-=-=-= At the request of the responder, here are main.cf and master.cf for a) the main postfix instance ("red.example.com") and b) the FBL instance ("blue.example.us") [NOTE: All parameters not specified below were left at the default Postfix 2.6 settings] MAIN: master.cf smtp inet n - n - - smtpd main.cf myhostname = red.example.com mydomain = example.com inet_interfaces = $myhostname, localhost inet_protocols = all lmtp_host_lookup = native smtp_host_lookup = native ignore_mx_lookup_error = yes mydestination = $myhostname, localhost.$mydomain, localhost local_recipient_maps = mynetworks = 192.168.34.104/32 relay_domains = example.com, example.info, example.net, example.org, example.us relayhost = [192.168.34.102] # Separate physical server, main mailserver. relay_recipient_maps = hash:/etc/postfix/relay_recipients alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases smtpd_banner = $myhostname ESMTP $mail_name multi_instance_wrapper = ${command_directory}/postmulti -p -- multi_instance_enable = yes multi_instance_directories = /etc/postfix-green /etc/postfix-pink /etc/postfix-orange /etc/postfix-blue FBL: master.cf 184.173.119.103:25 inet n - n - - smtpd main.cf myhostname = blue.example.us mydomain = blue.example.us <= Deliberately set to subdomain only. myorigin = $mydomain inet_interfaces = $myhostname lmtp_host_lookup = native smtp_host_lookup = native ignore_mx_lookup_error = yes mydestination = $myhostname local_recipient_maps = unix:passwd.byname $alias_maps $virtual_alias_maps mynetworks = 192.168.36.51/32, 192.168.35.20/31 <= Second IP is backup MX servers relay_domains = $mydestination recipient_canonical_maps = hash:/etc/postfix-blue/canonical virtual_alias_maps = hash:/etc/postfix-fbl/virtual alias_maps = hash:/etc/aliases, hash:/etc/postfix-blue/canonical alias_maps = hash:/etc/aliases, hash:/etc/postfix-blue/canonical mailbox_command = /usr/bin/procmail -a "$EXTENSION" DEFAULT=$HOME/Mail/ MAILDIR=$HOME/Mail smtpd_banner = $myhostname ESMTP $mail_name authorized_submit_users = multi_instance_name = postfix-blue multi_instance_enable = yes

    Read the article

  • File Server - Storage configuration: RAID vs LVM vs ZFS something else... ?

    - by privatehuff
    We are a small company that does video editing, among other things, and need a place to keep backup copies of large media files and make it easy to share them. I've got a box set up with Ubuntu Server and 4 x 500 GB drives. They're currently set up with Samba as four shared folders that Mac/Windows workstations can see fine, but I want a better solution. There are two major reasons for this: 500 GB is not really big enough (some projects are larger) It is cumbersome to manage the current setup, because individual hard drives have different amounts of free space and duplicated data (for backup). It is confusing now and that will only get worse once there are multiple servers. ("the project is on sever2 in share4" etc) So, I need a way to combine hard drives in such a way as to avoid complete data loss with the failure of a single drive, and so users see only a single share on each server. I've done linux software RAID5 and had a bad experience with it, but would try it again. LVM looks ok but it seems like no one uses it. ZFS seems interesting but it is relatively "new". What is the most efficient and least risky way to to combine the hdd's that is convenient for my users? Edit: The Goal here is basically to create servers that contain an arbitrary number of hard drives but limit complexity from an end-user perspective. (i.e. they see one "folder" per server) Backing up data is not an issue here, but how each solution responds to hardware failure is a serious concern. That is why I lump RAID, LVM, ZFS, and who-knows-what together. My prior experience with RAID5 was also on an Ubuntu Server box and there was a tricky and unlikely set of circumstances that led to complete data loss. I could avoid that again but was left with a feeling that I was adding an unnecessary additional point of failure to the system. I haven't used RAID10 but we are on commodity hardware and the most data drives per box is pretty much fixed at 6. We've got a lot of 500 GB drives and 1.5 TB is pretty small. (Still an option for at least one server, however) I have no experience with LVM and have read conflicting reports on how it handles drive failure. If a (non-striped) LVM setup could handle a single drive failing and only loose whichever files had a portion stored on that drive (and stored most files on a single drive only) we could even live with that. But as long as I have to learn something totally new, I may as well go all the way to ZFS. Unlike LVM, though, I would also have to change my operating system (?) so that increases the distance between where I am and where I want to be. I used a version of solaris at uni and wouldn't mind it terribly, though. On the other end on the IT spectrum, I think I may also explore FreeNAS and/or Openfiler, but that doesn't really solve the how-to-combine-drives issue.

    Read the article

  • Choice of an OS for a home ZFS NAS

    - by OlafM
    I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post. UPDATES Given the first answers, I will strongly suggest the person paying the hardware to insert a second HD. Better 2x2TB than 1x3TB (3 TB is oversized anyway). I was trying to keep the initial costs down to spread them over a longer period, but better having something good from the beginning.

    Read the article

  • IPv6: Should I have private addresses?

    - by AlReece45
    Right now, we have a rack of servers. Every server right now has at least 2 IP addresses, one for the public interface, another for the private. The servers that have SSL websites on them have more IP addresses. We also have virtual servers, that are configured similarly. Private Network The private range is currently just used for backups and monitoring. Its a gigabit port, the interface usage does not usually get very high. There are other technologies we're considering using that would use this port: iSCSI (implementations usually recommends dedicating an interface to it, which would be yet another IP network), VPN to get access to the private range (something I'd rather avoid) dedicated database servers LDAP centralized configuration (like puppet) centralized logging We don't have any private addresses in our DNS records (only public addresses). For our servers to utilize the correct IP address for the right interface (and not hard code the IP address) probably requires setting up a private DNS server (So now we add 2 different dns entries to 2 different systems). Public Network Our public range has a variety of services include web, email, and ftp. There is a hardware firewall between our network and the "public" network. We have (relatively secure) method to instruct the firewall to open and close administrative access (web interfaces, ssh, etc) for our current IP address. With either solution discussed, the host-based firewalls will be configured as well. The public network currently runs at a dedicated 20Mbps link. There are a couple of legacy servers with fast-ethernet ports, but they are scheduled for decommissioning. All of the other production boxes have at least 2 Gigabit Ethernet ports. The more traffic-heavy servers have 4-6 available (none is using more than the 2 Gigabit ports right now). IPv6 I want to get an IPv6 prefix from our ISP. So at least every "server" has at least one IPv6 interface. We'll still need to keep the IPv4 addressees up and available for legacy clients (web servers and email at the very least). We have two IP networks right now. Adding the public IPv6 address would make it three. Just use IPv6? I'm thinking about just dumping the private IPv4 range and using the IPv6 range as the primary means of all communications. If an interface starts reaching its capacity, utilize the newly free interfaces to create a trunk. It has the advantage that if either the public or private traffic needs to exceed 1Gbps. The traffic for each interface is already analyzed on a regular basis to predict future bandwidth use. In the rare instances where bandwidth unexpected peaks: utilize QoS to ensure traffic (like our limited SSH access) is prioritized correctly so the problem can be corrected (if possible, our WAN is the bottleneck right now). It also has the advantage of not needing to make an entry for every private address. We may have private DNS (or just LDAP), but it'll be much more limited in scope with less entries to duplicate. Summary I'm trying to make this network as "simple" as possible. At the same time, I want to make sure its reliable, upgradeable, scalable, and (eventually) redundant. Having one IPv6 network, and a legacy IPv4 network seems to be the best solution to me. Regarding using assigned IPv6 addresses for both networks, sharing the available bandwidth on one (more trunked if needed): Are there any technical disadvantages (limitations, buffers, scalability)? Are there any other security considerations (asides from firewalls mentioned above) to consider? Are there regulations or other security requirements (like PCI-DSS) that this doesn't meet? Is there typical software for setting up a Linux network that doesn't have IPv6 support yet? (logging, ldap, puppet) Some other thing I didn't consider?

    Read the article

  • Distributed and/or Parallel SSIS processing

    - by Jeff
    Background: Our company hosts SaaS DSS applications, where clients provide us data Daily and/or Weekly, which we process & merge into their existing database. During business hours, load in the servers are pretty minimal as it's mostly users running simple pre-defined queries via the website, or running drill-through reports that mostly hit the SSAS OLAP cube. I manage the IT Operations Team, and so far this has presented an interesting "scaling" issue for us. For our daily-refreshed clients, the server is only "busy" for about 4-6 hrs at night. For our weekly-refresh clients, the server is only "busy" for maybe 8-10 hrs per week! We've done our best to use some simple methods of distributing the load by spreading the daily clients evenly among the servers such that we're not trying to process daily clients back-to-back over night. But long-term this scaling strategy creates two notable issues. First, it's going to consume a pretty immense amount of hardware that sits idle for large periods of time. Second, it takes significant Production Support over-head to basically "schedule" the ETL such that they don't over-lap, and move clients/schedules around if they out-grow the resources on a particular server or allocated time-slot. As the title would imply, one option we've tried is running multiple SSIS packages in parallel, but in most cases this has yielded VERY inconsistent results. The most common failures are DTExec, SQL, and SSAS fighting for physical memory and throwing out-of-memory errors, and ETLs running 3,4,5x longer than expected. So from my practical experience thus far, it seems like running multiple ETL packages on the same hardware isn't a good idea, but I can't be the first person that doesn't want to scale multiple ETLs around manual scheduling, and sequential processing. One option we've considered is virtualizing the servers, which obviously doesn't give you any additional resources, but moves the resource contention onto the hypervisor, which (from my experience) seems to manage simultaneous CPU/RAM/Disk I/O a little more gracefully than letting DTExec, SQL, and SSAS battle it out within Windows. Question to the forum: So my question to the forum is, are we missing something obvious here? Are there tools out there that can help manage running multiple SSIS packages on the same hardware? Would it be more "efficient" in terms of parallel execution if instead of running DTExec, SQL, and SSAS same machine (with every machine running that configuration), we run in pairs of three machines with SSIS running on one machine, SQL on another, and SSAS on a third? Obviously that would only make sense if we could process more than the three ETL we were able to process on the machine independently. Another option we've considered is completely re-architecting our SSIS package to have one "master" package for all clients that attempts to intelligently chose a server based off how "busy" it already is in terms of CPU/Memory/Disk utilization, but that would be a herculean effort, and seems like we're trying to reinvent something that you would think someone would sell (although I haven't had any luck finding it). So in summary, are we missing an obvious solution for this, and does anyone know if any tools (for free or for purchase, doesn't matter) that facilitate running multiple SSIS ETL packages in parallel and on multiple servers? (What I would call a "queue & node based" system, but that's not an official term). Ultimately VMWare's Distributed Resource Scheduler addresses this as you simply run a consistent number of clients per VM that you know will never conflict scheduleing-wise, then leave it up to VMWare to move the VMs around to balance out hardware usage. I'm definitely not against using VMWare to do this, but since we're a 100% Microsoft app stack, it seems like -someone- out there would have solved this problem at the application layer instead of the hypervisor layer by checking on resource utilization at the OS, SQL, SSAS levels. I'm open to ANY discussion on this, and remember no suggestion is too crazy or radical! :-) Right now, VMWare is the only option we've found to get away from "manually" balancing our resources, so any suggestions that leave us on a pure Microsoft stack would be great. Thanks guys, Jeff

    Read the article

  • Windows 7 disk errors after a few hours of runtime

    - by GFK
    I'm having trouble understanding what is going on with my work PC. Whenever I boot it, it runs fine for a while, then starts to randomly show disk errors. The displayed error often contains the message "not enough storage is available to process this command", although depending on the application that fails it can be different. This has happened for weeks now and is getting worse. This is what troubles me: It never seems to impact critical parts of the system (no BSOD, no freeze). Only some applications seem impacted, refusing to function correctly after a while: Outlook 2010 cannot download RSS feeds anymore, Firefox 6 or IE9 cannot download anything bigger than 3MB without failing, Windows Update fails, all msi installers fail, Visual Studio 2010 starts failing in weird manners... It only happens after a while using it (typically 3 hours, but it seems that installing a program or compiling several times makes it shorter) Rebooting solves it (temporarily). The system: The OS is Windows 7 Pro Spanish SP1, 32 bits The system is an HP Compaq 6000 Pro with 4 GB memory (only 3.4GB usable since the system is 32bit), one 500GB hard drive. Installed applications include: Visual Studio 2010, SQL Server 2008 R2, VMWare Workstation 7, Microsoft Security Essentials, Office 2010. Shutting down all related services and processes doesn't seem to change anything. The diagnostics I've run so far: Hard drive : 465GB, 165GB free Process Explorer : physical and virtual memory seem ok (pagefile is 5.3GB, physical memory usage 70%, system commit 39%) Windows Memory diagnostic tool: OK CHKDSK returned: 488282111 KB total disk space. 281668248 KB in 265779 files. 150188 KB in 62949 indexes. 0 KB in bad sectors. 571755 KB in use by the system. The log file has occupied 65536 kilobytes. 205891920 KB available on disk. For non-spanish speakers, that means all ok. SMART diagnostic tools (DiskCheckup) report all values normal. temperatures are in the normal range (HWinfo). The event viewer doesn't seem to contain any significant message. ran CCleaner 3, without any noticeable effect. I was thinking about some file number limit (between Visual Studio projects and other applications, there are around 300.000 files on the hard drive), but I couldn't find any. It's possible there is something related with the use of the temporary folders (it's the only explanation I have for why applications fail but Windows doesn't), but I cannot confirm that. Only thing I cannot find out is if chkdsk reporting 65MB for the log is normal. It seems since Vista it always reports this. Any other cleaning/diagnostic tool you might know of? Edit: I ran several other tools since I first published the question: Seagate SeaTools (the HD manufacturer's analysis tool): complete test run OK. Intel Rapid 10.1 (the HD controller manufacturer's troubleshooting tool): the HD's ok. Microsoft Desktop Heap Monitor: Desktop Heap Information Monitor Tool (Version 8.1.2925.0) Copyright (c) Microsoft Corporation. All rights reserved. Session ID: 1 Total Desktop: ( 46464 KB - 11 desktops) WinStation\Desktop Heap Size(KB) Used Rate(%) WinSta0\Winlogon (s1) 128 3.6 WinSta0\Disconnect (s1) 64 3.8 WinSta0\Default (s1) 20480 3.0 msswindowstation\mssrestricteddesk (s0) 1024 0.2 __X78B95_89_IW__A8D9S1_42_ID (s0) 1024 0.2 Service-0x0-3e5$\Default (s0) 1024 0.6 Service-0x0-3e4$\Default (s0) 1024 0.3 Service-0x0-3e7$\Default (s0) 1024 2.1 WinSta0\Winlogon (s0) 128 1.9 WinSta0\Disconnect (s0) 64 3.8 WinSta0\Default (s0) 20480 0.0 All ok, desktop heap usage < 5% Edit 2: I tried totally resetting my account by creating a new one, logging under this new one and delete the first one (local rights and files), then logging back with this deleted account (it is a domain account). No luck. Also, I found out often the error is "not enough storage is available to process this command". Searching on the internet, I found an old troubleshooting tip (setting a registry key to raise the IRP stack limit, whatever it is) which did not change anything.

    Read the article

< Previous Page | 507 508 509 510 511 512 513 514 515 516 517 518  | Next Page >