Search Results

Search found 32459 results on 1299 pages for 'no internet connection'.

Page 514/1299 | < Previous Page | 510 511 512 513 514 515 516 517 518 519 520 521  | Next Page >

• Cisco: Site-to-site VPN with cisco 878 and ASA weirdness

  - by cpf

  I currently have 2 sites, both connected to each other through 2 firewalls / routers in a site-to-site VPN. Pinging from server to server (Using 2mb/2mb SDSL) through that VPN obviously works, however, at one site, we have another internet connection (7m/400k ADSL), and only the link between the two sites should be on the other connection. All pc's should go over the other connection for internet, just communication between servers & Communication between pc's and the server at the other side should go through there too. What is configured at the moment is the server is using the SDSL directly as default gateway. Since it's not intended to surf anything it is a safe config. PC's are configured on the ADSL as default gateway. Now I wanted to route through everything that uses the range used on the other site, it should be sent from the ADSL modem to the SDSL modem, which has the VPN connection. I figured I could use OSPF to do so, however, OSPF doesn't seem to "detect" the range of the external site. Also (due to bad ip subnetting thanks to the other administrator), the ip used internally as the server on the other site also exists on the internet (causing a lot of confusion), so rdp-ing from our server to the server of the other site works (somehow), but tracerouting on the SDSL router (which should actually, in my opinion, go over the VPN) actually goes all over the internet. My question(s): Why doesn't the SDSL router ping the external ip through VPN, but the server does? Why can't I route from the ADSL router to the SDSL over VPN? I would seriously appreciate some help, since I can't figure out why it does it like this.

  Read the article

• pfSense: How to route traffic out the WAN port?

  - by Ian Boyd

  Expert version i want to create a route in pfSense that will send traffic out the physical WAN port, not the PPPoE WAN port. i want to talk to talk to the web-server on my DSL modem, but it doesn't see packets wrapped in a PPPoE header. Long version My pfSense router is responsible for setting up the PPPoE connection over DSL to my ISP. When a machine on the LAN wants to sent packets to the internet, the default route sends packets out over the PPPoE connection. Those packets, wrapped in a PPPoE header, are sent on the ethernet cable to my DSL modem. From there they are sent the ISP, and the internet at large. i want a way to send a packet out the WAN port itself - not the PPPoE WAN port. My modem is sitting out there, with a http interface where i can monitor connection speed signal-to-noise ratio bandwidth connection time Whenever i try to set a route for destination of 192.168.2.1 (the IP that the modem will listen to for HTTP requests) to go out the WAN port, they instead end up going out the PPPoE port. The difference being that they're wrapped in a PPPoE protocol packet, and the modem isn't being sent the packet, it's being delivered to the ISP. Given that pfSense has no ability to direct traffic out the physical WAN port: how can i direct traffic out the physical WAN port on pfSense?

  Read the article

• Cisco SR520w FE - WAN Port Stops Working

  - by Mike Hanley

  I have setup a Cisco SR520W and everything appears to be working. After about 1-2 days, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device. If I unplug and then plug in the network cable connecting the WAN port of the SR520W to my Comcast Cable Modem, traffic startings flowing again. Also, if I restart the SR520W, the traffic will flow again. Any ideas? Here is the running config: Current configuration : 10559 bytes ! version 12.4 no service pad no service timestamps debug uptime service timestamps log datetime msec no service password-encryption ! hostname hostname.mydomain.com ! boot-start-marker boot-end-marker ! logging message-counter syslog no logging rate-limit enable secret 5 <removed> ! aaa new-model ! ! aaa authentication login default local aaa authorization exec default local ! ! aaa session-id common clock timezone PST -8 clock summer-time PDT recurring ! crypto pki trustpoint TP-self-signed-334750407 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-334750407 revocation-check none rsakeypair TP-self-signed-334750407 ! ! crypto pki certificate chain TP-self-signed-334750407 certificate self-signed 01 <removed> quit dot11 syslog ! dot11 ssid <removed> vlan 75 authentication open authentication key-management wpa guest-mode wpa-psk ascii 0 <removed> ! ip source-route ! ! ip dhcp excluded-address 172.16.0.1 172.16.0.10 ! ip dhcp pool inside import all network 172.16.0.0 255.240.0.0 default-router 172.16.0.1 dns-server 10.0.0.15 10.0.0.12 domain-name mydomain.com ! ! ip cef ip domain name mydomain.com ip name-server 68.87.76.178 ip name-server 66.240.48.9 ip port-map user-ezvpn-remote port udp 10000 ip ips notify SDEE ip ips name sdm_ips_rule ! ip ips signature-category category all retired true category ios_ips basic retired false ! ip inspect log drop-pkt no ipv6 cef ! multilink bundle-name authenticated parameter-map type inspect z1-z2-pmap audit-trail on password encryption aes ! ! username admin privilege 15 secret 5 <removed> ! crypto key pubkey-chain rsa named-key realm-cisco.pub key-string <removed> quit ! ! ! ! ! ! crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 connect auto group EZVPN_GROUP_1 key <removed> mode client peer 64.1.208.90 virtual-interface 1 username admin password <removed> xauth userid mode local ! ! archive log config logging enable logging size 600 hidekeys ! ! ! class-map type inspect match-any SDM_AH match access-group name SDM_AH class-map type inspect match-any SDM-Voice-permit match protocol sip class-map type inspect match-any SDM_ESP match access-group name SDM_ESP class-map type inspect match-any SDM_EASY_VPN_REMOTE_TRAFFIC match protocol isakmp match protocol ipsec-msft match class-map SDM_AH match class-map SDM_ESP match protocol user-ezvpn-remote class-map type inspect match-all SDM_EASY_VPN_REMOTE_PT match class-map SDM_EASY_VPN_REMOTE_TRAFFIC match access-group 101 class-map type inspect match-any Easy_VPN_Remote_VT match access-group 102 class-map type inspect match-any sdm-cls-icmp-access match protocol icmp match protocol tcp match protocol udp class-map type inspect match-any sdm-cls-insp-traffic match protocol cuseeme match protocol dns match protocol ftp match protocol h323 match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp extended match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udp class-map type inspect match-any L4-inspect-class match protocol icmp class-map type inspect match-all sdm-invalid-src match access-group 100 class-map type inspect match-all dhcp_out_self match access-group name dhcp-resp-permit class-map type inspect match-all dhcp_self_out match access-group name dhcp-req-permit class-map type inspect match-all sdm-protocol-http match protocol http ! ! policy-map type inspect sdm-permit-icmpreply class type inspect dhcp_self_out pass class type inspect sdm-cls-icmp-access inspect class class-default pass policy-map type inspect sdm-permit_VT class type inspect Easy_VPN_Remote_VT pass class class-default drop policy-map type inspect sdm-inspect class type inspect SDM-Voice-permit pass class type inspect sdm-cls-insp-traffic inspect class type inspect sdm-invalid-src drop log class type inspect sdm-protocol-http inspect z1-z2-pmap class class-default pass policy-map type inspect sdm-inspect-voip-in class type inspect SDM-Voice-permit pass class class-default drop policy-map type inspect sdm-permit class type inspect SDM_EASY_VPN_REMOTE_PT pass class type inspect dhcp_out_self pass class class-default drop ! zone security ezvpn-zone zone security out-zone zone security in-zone zone-pair security sdm-zp-in-ezvpn1 source in-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-ezpn1 source out-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-ezvpn-out1 source ezvpn-zone destination out-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-self-out source self destination out-zone service-policy type inspect sdm-permit-icmpreply zone-pair security sdm-zp-out-in source out-zone destination in-zone service-policy type inspect sdm-inspect-voip-in zone-pair security sdm-zp-ezvpn-in1 source ezvpn-zone destination in-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-self source out-zone destination self service-policy type inspect sdm-permit zone-pair security sdm-zp-in-out source in-zone destination out-zone service-policy type inspect sdm-inspect ! bridge irb ! ! interface FastEthernet0 switchport access vlan 75 ! interface FastEthernet1 switchport access vlan 75 ! interface FastEthernet2 switchport access vlan 75 ! interface FastEthernet3 switchport access vlan 75 ! interface FastEthernet4 description $FW_OUTSIDE$ ip address 75.149.48.76 255.255.255.240 ip nat outside ip ips sdm_ips_rule out ip virtual-reassembly zone-member security out-zone duplex auto speed auto crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 ! interface Virtual-Template1 type tunnel no ip address ip virtual-reassembly zone-member security ezvpn-zone tunnel mode ipsec ipv4 ! interface Dot11Radio0 no ip address ! encryption vlan 75 mode ciphers aes-ccm ! ssid <removed> ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Dot11Radio0.75 encapsulation dot1Q 75 native ip virtual-reassembly bridge-group 75 bridge-group 75 subscriber-loop-control bridge-group 75 spanning-disabled bridge-group 75 block-unknown-source no bridge-group 75 source-learning no bridge-group 75 unicast-flooding ! interface Vlan1 no ip address ip virtual-reassembly bridge-group 1 ! interface Vlan75 no ip address ip virtual-reassembly bridge-group 75 bridge-group 75 spanning-disabled ! interface BVI1 no ip address ip nat inside ip virtual-reassembly ! interface BVI75 description $FW_INSIDE$ ip address 172.16.0.1 255.240.0.0 ip nat inside ip ips sdm_ips_rule in ip virtual-reassembly zone-member security in-zone crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 inside ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 75.149.48.78 2 ! ip http server ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ip nat inside source list 1 interface FastEthernet4 overload ! ip access-list extended SDM_AH remark SDM_ACL Category=1 permit ahp any any ip access-list extended SDM_ESP remark SDM_ACL Category=1 permit esp any any ip access-list extended dhcp-req-permit remark SDM_ACL Category=1 permit udp any eq bootpc any eq bootps ip access-list extended dhcp-resp-permit remark SDM_ACL Category=1 permit udp any eq bootps any eq bootpc ! access-list 1 remark SDM_ACL Category=2 access-list 1 permit 172.16.0.0 0.15.255.255 access-list 100 remark SDM_ACL Category=128 access-list 100 permit ip host 255.255.255.255 any access-list 100 permit ip 127.0.0.0 0.255.255.255 any access-list 100 permit ip 75.149.48.64 0.0.0.15 any access-list 101 remark SDM_ACL Category=128 access-list 101 permit ip host 64.1.208.90 any access-list 102 remark SDM_ACL Category=1 access-list 102 permit ip any any ! ! ! ! snmp-server community <removed> RO ! control-plane ! bridge 1 protocol ieee bridge 1 route ip bridge 75 route ip banner login ^CSR520 Base Config - MFG 1.0 ^C ! line con 0 no modem enable line aux 0 line vty 0 4 transport input telnet ssh ! scheduler max-task-time 5000 end I also ran some diagnostics when the WAN port stopped working: 1. show interface fa4 FastEthernet4 is up, line protocol is up Hardware is PQUICC_FEC, address is 0026.99c5.b434 (bia 0026.99c5.b434) Description: $FW_OUTSIDE$ Internet address is 75.149.48.76/28 MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 01:08:15, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/23/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 0 packets/sec 336446 packets input, 455403158 bytes Received 23 broadcasts, 0 runts, 0 giants, 37 throttles 41 input errors, 0 CRC, 0 frame, 0 overrun, 41 ignored 0 watchdog 0 input packets with dribble condition detected 172529 packets output, 23580132 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out 2. show ip route Gateway of last resort is 75.149.48.78 to network 0.0.0.0 C 192.168.75.0/24 is directly connected, BVI75 64.0.0.0/32 is subnetted, 1 subnets S 64.1.208.90 [1/0] via 75.149.48.78 S 192.168.10.0/24 is directly connected, BVI75 75.0.0.0/28 is subnetted, 1 subnets C 75.149.48.64 is directly connected, FastEthernet4 S* 0.0.0.0/0 [2/0] via 75.149.48.78 3. show ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet 75.149.48.65 69 001e.2a39.7b08 ARPA FastEthernet4 Internet 75.149.48.76 - 0026.99c5.b434 ARPA FastEthernet4 Internet 75.149.48.78 93 0022.2d6c.ae36 ARPA FastEthernet4 Internet 192.168.75.1 - 0027.0d58.f5f0 ARPA BVI75 Internet 192.168.75.12 50 7c6d.62c7.8c0a ARPA BVI75 Internet 192.168.75.13 0 001b.6301.1227 ARPA BVI75 4. sh ip cef Prefix Next Hop Interface 0.0.0.0/0 75.149.48.78 FastEthernet4 0.0.0.0/8 drop 0.0.0.0/32 receive 64.1.208.90/32 75.149.48.78 FastEthernet4 75.149.48.64/28 attached FastEthernet4 75.149.48.64/32 receive FastEthernet4 75.149.48.65/32 attached FastEthernet4 75.149.48.76/32 receive FastEthernet4 75.149.48.78/32 attached FastEthernet4 75.149.48.79/32 receive FastEthernet4 127.0.0.0/8 drop 192.168.10.0/24 attached BVI75 192.168.75.0/24 attached BVI75 192.168.75.0/32 receive BVI75 192.168.75.1/32 receive BVI75 192.168.75.12/32 attached BVI75 192.168.75.13/32 attached BVI75 192.168.75.255/32 receive BVI75 224.0.0.0/4 drop 224.0.0.0/24 receive 240.0.0.0/4 drop 255.255.255.255/32 receive Thanks in advance, -Mike

  Read the article

• python mysqldb - mysql server gone away - can't reconnect

  - by david.barkhuizen

  Hi Folks, When attempting to import a bunch of data into mysql tables using python and mysqldb, I run into the following error '2006 - mySQL Server has gone away', and then I am unable to reconnect again within the script. I am iniitially re-using a connection object across transactions ( delineated by conn.commit() ), then when I first encounter this exception, if I create a new connection by calling MySQLdb.connect(), this new connection also fails with the same exception. This error does not occur immediately, I can pump a fair amount of data into the db, but then faithfully occurs after I have inserted a couple thousand records, so roughly once the db has committed a certain transaction volume, it always falls over like this. If I rerun the script, WITHOUT restarting the db server. then it resumes where it left off, pumps in some data, then falls over again. Before recommendations to change time-out timings, does anyone know why I am not able to establish a new connection after the initial failure ? - Even if I try a couple of times waiting a couple of seconds between each. (btw, I'm running Windows 7, mysql server 5.1.48, mysqldb 1.2.3.gamma.1, python 2.6)

  Read the article

• Unexpected behaviour when dynamically add node in HAproxy server

  - by Anand Soni

  I wanted to use HAProxy for my web app for load balancing purpose. I am trying to add a new rabbitmq node dynamically in HAProxy server using command : haproxy -p /var/run/haproxy.pid -sf $(cat /var/run/haproxy.pid). I am doing tcp connection mode with leastconn balance algorithm in load balancing. What is expected is when there is 3 connection in one rabbitmq, I add a new rabbit server in HAProxy server. so the next connection would pass to 2nd rabbitmq server which is not happening in my case. It distributes the connection in haphazardly manner. Here is my config file: defaults log global mode http option httplog option dontlognull retries 3 option redispatch maxconn 2000 contimeout 5000 clitimeout 5000 srvtimeout 5000 listen rabbitmq 0.0.0.0:5672 mode tcp stats enable balance leastconn option tcplog server rabbit01 xx.xx.xx.xx:5672 check server rabbit02 xx.xx.xx.xx:5672 check listen tomcatq 0.0.0.0:80 mode http stats enable balance roundrobin stats refresh 10s stats refresh 10s stats uri /lb?stats stats auth admin:admin option httplog What is the problem causing this behavior? Any suggestion will appreciated.

  Read the article

• SQL Server 2008: Can't connect to remote server via management studio but can telnet in fine

  - by WarpKid

  Hi, I am in the process of trying to configure SQL Server 2008 to accept remote connections. I have been through all the documentation I can find and yet when I attempt to connect through management studio I get an error stating that the server could not be found. Interestingly I can connect through telnet to the remote server via the port that sql server is listening on. In the SQL Server logs I can see the connection attempt. So SQL Server is up and running and listening on the correct port - no firewall blocking it. It would appear that by default SQL Server is listening on port 50314 by default but management studio attempts to connect on port 1433.Weird. Server Management Studio = no dice. Anyone got any ideas? Server is set to allow remote connections - TCP IP is enabled, firewall is off. Thanks UPDATE FOR TO CLEAR THINGS UP A BIT We are seeing the connection attempt when we telnet in on port 50314 in the sql server logs. When we login through management studio we see it attempting connection on port 1433. There is no sign of this connection attempt in the logs.

  Read the article

• How to restore infrared support in Windows XP?

  - by Emil Rasmussen

  My infrared port is not working on my Windows XP SP 3 (Thinkpad X60). I can see it Device Manager, and it's status is, that it is working probably. The problem manifests in several ways. Originally I was trying to transfer data from my Polar RS800CX watch, and the Polar ProTrainer 5 software gave me the this error message: "Communication port couldn't be opened". Then I tried to connect the watch to another computer, and the infrared connection was established immediately. I then tried to connect the other computer to my Thinkpad X60. The other computer again immediately showed the Wireless Link icon "'computername' is in range" in the notification area. But nothing is shown on the Thinkpad, and a file transfer to the Thinkpad is unsuccessful with an error message that reports that "the target machine actively refused it [the connection]". This brings me to conclude that the infrared support in Windows on the Thinkpad is somehow broken. This is further supported by the fact that I can't find the "Wireless Link" icon in the Control Panel and when I try to run the irprops.cpl nothing happens. So the question is, how to reinstall the infrared support? Some of the solutions that I have explored is: I have tried to disable/enable the infrared in the BIOS - to trick a re-installation. The IR modules settings on the other computer that can get a successful IR connection is an exact match to the ThinkPad that can't get a connection. The was a problem in Windows XP SP 2 with the Wireless Link icon - MS KB article - but that hotfix can't be applied on SP 3 installation. I also guess that the hotfix is included in SP 3. Any other suggestions?

  Read the article

• Server and Network Lag

  - by DanSpd

  At my home I have a server and my computer. Server has Windows Server 2008 Standart 64 bit installed and then my computer has Windows 7 64 bit installed. My home router is DIR-615 My server has a game server installed on it and basically total open connections on server are around 700. Once its around 700 server and then whole home network lags really badly. My internet connection is good and only around 600kb/s is being used out of 2mb/s (real download/upload speeds). So far I assume that my router has a connection limit and with server + my computer connections it peaks at around 1k and lags everything. Another assumption server lag comes from connection limit. On the internet I have read that standart version of server has connection limit of 700 + 10 reserved. I do not rmember where I found that information but it was on microsoft website. So I have two options. First is to upgrade my router to Netgear FVS318G-100 and second is to change connections limit on server. Any advices? Thank you

  Read the article

• Server and Network Lag

  - by DanSpd

  At my home I have a server and my computer. Server has Windows Server 2008 Standart 64 bit installed and then my computer has Windows 7 64 bit installed. My home router is DIR-615 My server has a game server installed on it and basically total open connections on server are around 700. Once its around 700 server and then whole home network lags really badly. My internet connection is good and only around 600kb/s is being used out of 2mb/s (real download/upload speeds). So far I assume that my router has a connection limit and with server + my computer connections it peaks at around 1k and lags everything. Another assumption server lag comes from connection limit. On the internet I have read that standart version of server has connection limit of 700 + 10 reserved. I do not rmember where I found that information but it was on microsoft website. So I have two options. First is to upgrade my router to Netgear FVS318G-100 and second is to change connections limit on server. Any advices? Thank you

  Read the article

• Server and Network Lag

  - by DanSpd

  At my home I have a server and my computer. Server has Windows Server 2008 Standart 64 bit installed and then my computer has Windows 7 64 bit installed. My home router is DIR-615 My server has a game server installed on it and basically total open connections on server are around 700. Once its around 700 server and then whole home network lags really badly. My internet connection is good and only around 600kb/s is being used out of 2mb/s (real download/upload speeds). So far I assume that my router has a connection limit and with server + my computer connections it peaks at around 1k and lags everything. Another assumption server lag comes from connection limit. On the internet I have read that standart version of server has connection limit of 700 + 10 reserved. I do not rmember where I found that information but it was on microsoft website. So I have two options. First is to upgrade my router to Netgear FVS318G-100 and second is to change connections limit on server. Any advices? Thank you

  Read the article

• Cisco SG 300-28P PoE switch appears to have damaged my domain server's network IF

  - by cdonner

  I just replaced the old HP ProCurve switch with a new Cisco SG 300-28P managed switch. It has PoE on all ports. Everything works, except for my domain server that went offline and the network interface appears to be dead. Windows says the network cable is disconnected, and no lights blink on the switch. Tried different cables and different ports on the switch. The Cisco PoE ports are supposed to be auto-sensing, i.e. not to send power to a device that cannot handle it. Is this technique not 100% reliable? The server is a SHUTTLE XS35V2 with an onboard network chip, so it is probably fried. My questions: is this plausible? who's fault is it - Shuttle or Cisco (i.e. which support line should I try first)? UPDATE: I did go back and tried another switch between the server and the Cisco switch, and indeed, the connection came back to live. When everything is powered down and I start fresh, with the server connected to the Cisco switch, the port light will blink for a while and the connection status is "No Internet connection" at first until it goes off after about 20 seconds and the connection status changes to "Network cable disconnected". On the other switch it works. Clearly not a PoE issue now. I will start looking into the Cisco's onboard diagnostic functions, but so far I have not noticed anything unusual in the log.

  Read the article

• Unable to add datasource in ColdFusion 9 and SQL Server 2008 R2

  - by Evik James

  I just installed SQL Server 2008 R2 and ColdFusion 9.0.1 on my Windows 7 machine for development use only. I have ColdFusion running well and serving pages (that aren't connected to a database). I can view my databases in SQL Server Management Studio. I successfully restored a few small databases and now I am trying to set up datasources for them through the ColdFusion Administrator. On my other machine, this was super easy. Not so much this time. The database I just added is named "Test". I am getting this error: Connection verification failed for data source: Test java.sql.SQLNonTransientConnectionException: [Macromedia][SQLServer JDBC Driver]Error establishing socket to host and port: localhost:1433. Reason: Connection refused: connect The root cause was that: java.sql.SQLNonTransientConnectionException: [Macromedia][SQLServer JDBC Driver]Error establishing socket to host and port: localhost:1433. Reason: Connection refused: connect It looks like the connection between ColdFusion and SQL Server is being refused. I know, brilliant observation, right? On my other machine, I was able to create datasources with just the default settings, no server name, username, or password. Any clue as to what might be the cause and how I might fix it?

  Read the article

• Fedora, ssh and sudo

  - by Ricky Robinson

  I have to run a script remotely on several Fedora machines through ssh. Since the script requires root priviliges, I do: $ ssh me@remost_host "sudo touch test_sudo" #just a simple example sudo: no tty present and no askpass program specified The remote machines are configured in such a way that the password for sudo is never asked for. For the above error, the most common fix is to allocate a pseudo-terminal with the -t option in ssh: $ ssh -t me@remost_host "sudo touch test_sudo" sudo: no tty present and no askpass program specified Let's try to force this allocation with -t -t: $ ssh -t -t me@remost_host "sudo touch test_sudo" sudo: no tty present and no askpass program specified Nope, it doesn't work. In /etc/sudoers of course I have this line: #Defaults requiretty ... but I can't manually change it on tens of remote machines. Am I missing something here? Is there an easy fix? EDIT: Here is the sudoers file of a host where ssh me@host "sudo stat ." works. Here is the sudoers file of a host where it doesn't work. EDIT 2: Running tty on a host where it works: $ ssh me@host_ok tty not a tty $ ssh -t me@host_ok tty /dev/pts/12 Connection to host_ok closed. $ ssh -t -t me@host_ok tty /dev/pts/12 Connection to host_ok closed. Now on a host where it doesn't work: $ ssh me@host_ko tty not a tty $ ssh -t me@host_ko tty not a tty Connection to host_ko closed. $ ssh -t -t me@host_ko tty not a tty Connection to host_ko closed.

  Read the article

• Default route not on LAN

  - by jarmund

  I have a network that in principle looks like this: H1---\ /----Inet1 H2---->---GW1---< H3---/ \----GW2-----Inet2 H1 and H2 = Hosts that need access to internet with GW1 Inet1 = Internet link over 3G connection Inet2 = 5GHz link to Internet (not always up) GW1 = Works as a router, automatically picking the "best" connection between Inet1 and Inet2 (the latter via GW2). GW2 = 5GHz wifi router And here's the problem: H3 only needs internet access when Inet2 is up. What i was thinking of doing was a routing table that looks like this: route to GW2 via GW1 default route is via GW2 I first set the route to GW2 via GW1 without a problem. But when i try route add default gw 1.2.3.4 (1.2.3.4 being the IP of GW2), it complains "SIOCADDRT: No such device" Is the problem that the default gw i'm trying to set is not reachable directly? Is there a different approach that would allow me to achieve this? An alternative (and hypothetical) approach: Since H3 will be using a static IP, is it possible to do some magic with iptables on GW1 to forward any packets from H3 to GW3, thereby "tricking" H3 into using GW2 as its default router?

  Read the article

• SSH over HTTPS with proxytunnel and nginx

  - by Thermionix

  I'm trying to setup an ssh over https connection using nginx. I haven't found any working examples, so any help would be appreciated! ~$ cat .ssh/config Host example.net Hostname example.net ProtocolKeepAlives 30 DynamicForward 8118 ProxyCommand /usr/bin/proxytunnel -p ssh.example.net:443 -d localhost:22 -E -v -H "User-Agent: Mozilla/4.0 (compatible; MSIE 6.0; Win32)" ~$ ssh [email protected] Local proxy ssh.example.net resolves to 115.xxx.xxx.xxx Connected to ssh.example.net:443 (local proxy) Tunneling to localhost:22 (destination) Communication with local proxy: -> CONNECT localhost:22 HTTP/1.0 -> Proxy-Connection: Keep-Alive -> User-Agent: Mozilla/4.0 (compatible; MSIE 6.0; Win32) <- <html> <- <head><title>400 Bad Request</title></head> <- <body bgcolor="white"> <- <center><h1>400 Bad Request</h1></center> <- <hr><center>nginx/1.0.5</center> <- </body> <- </html> analyze_HTTP: readline failed: Connection closed by remote host ssh_exchange_identification: Connection closed by remote host Nginx config on the server; ~$ cat /etc/nginx/sites-enabled/ssh upstream tunnel { server localhost:22; } server { listen 443; server_name ssh.example.net; location / { proxy_pass http://tunnel; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_redirect off; } ssl on; ssl_certificate /etc/ssl/certs/server.cer; ssl_certificate_key /etc/ssl/private/server.key; } ~$ tail /var/log/nginx/access.log 203.xxx.xxx.xxx - - [08/Feb/2012:15:17:39 +1100] "CONNECT localhost:22 HTTP/1.0" 400 173 "-" "-"

  Read the article

• Hints on diagnosing performance issue in OpenBSD firewall

  - by Tom

  My OpenBSD 4.6 pf firewall has started having really bad performance in the past few weeks. I've isolated the firewall (as opposed to the WAN connection, switch, cable, etc.) as the problem, but need a hint on how to further diagnose or fix the problem. The facts: Normal setup is: DSL Modem - FW Ext. NIC - FW Int. NIC - Switch - Laptop Normal setup described above gives only 25 Kbps! Plugging the laptop straight from the DSL modem gives a 1 MBps connection (full speed, as advertised). Therefore, the DSL connection seems to be OK. Plugging the laptop directly into the firewall's internal NIC (bypassing the switch) also gives only 25 Kbps. Therefore, the switch does not seem to be a problem. I've replaced the ethernet cables, but it didn't help. Here's the weird thing. Reloading the ruleset (/sbin/pfctl -Fa -f /etc/pf.conf) causes the laptop's connection to go up to 1 Mbps (i.e. full speed) for a few minutes before it gradually degrades back down to 25Kbps again. Any ideas on what's wrong or how I could further diagnose the problem?

  Read the article

• Networking problems in VMWare with wireless bridge

  - by Robert Koritnik

  Barebone data: virtualization: VMWare Workstation 6.5 (latest) Host: Windows Server 2008 x64 Guest: Windows Server 2008 x86 Host network adapter: wireless Guest network adapter 1: over Bridge VMNet (automatic) Guest network adapter 2: over Host only VMNet Problem When I surf the net within VM my internet connection just gets stalled (not dropped). It doesn't experience any timeout whatsoever, it just stops downloading/communicating. For instance: I start downloading a file with a browser (IE/FF/CR doesn't matter) and I have to pause/restart download when speed drops to 0. I could wait indefinitelly but connection won't pickup automatically. What did I miss in my network configuration? Update 1 I've tested this in various combinations. This works fine when host is connected via Ethernet. But when connected via Wifi, the connection on the guest works as previously described. It connects fine. It gets a valid IP from DHCP... Everything is cool as long as you don't start doing some intensive network traffic (ie. download a 2MB file) In this case it starts downloading and stops after a while. Speed just drops to 0B/s... Sometimes it picks up back, sometimes it doesn't. Connection still stays and works. I can ping around with no problem.

  Read the article

• OSX: Mimic Ubuntu IP Masquerading via iptables with ipfw

  - by Dogbert

  Good day, I am attempting to replicate a setup I have between a router and an Ubuntu PC, and have the same setup working on my MacBook (10.6, Snow Leopard). First, I have a router that has a USB port. When I plug it into my Ubuntu PC, it creates an RNDIS connection, allowing me to connect to the router over the USB cable via an IP connection. When I plug it into my computer via USB, it gets assigned an IP address of 172.16.84.1, and a new adapter appears when I type ifconfig. I can then SSH into the device via ssh [email protected]. When I log in to the device, I flush the routes, then create the default route: admin@localhost> route -f admin@localhost> route add default 172.16.84.2 Now, in my Ubuntu machine, I use iptables to enable IP masquerading: root@Valhalla> sudo iptables -t nat -A POSTROUTING -s 172.16.84.2 -j MASQUERADE Once this is all done, the router has internet access over the USB connection to my PC. I am trying to replicate this exact setup on my MacBook now (Snow Leopard), but iptables does not exist for OSX, not even a Macports version exists. I have scoured through other questions on StackOverflow that cover the usage of the ipfw command, which apparently works as a drop-in replacement for iptables. However, the syntax is significantly different, and I'm pretty much lost. Does anyone with some experience with ipfw have some suggestions on how I could accomplish this and create a NAT connection via IP masquerading like I could with my Ubuntu PC? Thank you for your assistance.

  Read the article

• can't Remote desktop to windows XP, blaming the server side

  - by Jin

  After rebooting my work PC (windows XP sp3) this Wednesday (thank to Microsoft Tuesday), I found that I can't remote desktop to my work PC from home (with VPN to company). I have been remote-desktop to work for years and I am really surprised since connectivity is not the problem, so I brought up wireshark to sniff the packets. I can see after TCP handshake, client sent X.224 Connection Request 03 00 00 13 0e e0 00 00 00 00 00 01 00 08 00 03 00 00 00 server sent X.224 Connection Confirm. 03 00 00 0b 06 d0 00 00 12 34 00 According to "MS-RDPBCGR", the official spec on RDP, the server should include Negotiation Response in the "Connection Confirm" message but it didn't. It's empty. I googled a lot but didn't find any clue on why server did that. By the way, I used the same remote desktop client and can connect to other windows XP PC. Here are a couple of pieces of information that may help to give a clue: Since TCP handshake (server port being 3389), I believe the svchost service is actually running. going to control panel -- system window, --- "Remote" tab, the remote desktop is indeeded checked and it states that my username is allowed. according to the packet capture, client didn't even get a chance to tell server what user was trying to logon. Yes, the progress bar showed up a few seconds and then it went back to the "Remote desktop Connection" window again. Searched "windowsupdate.log", didn't find any appearance of the word "remote".

  Read the article

• How to connect through a proxy using Remote Desktop?

  - by scottmarlowe

  So I've got a home server running Windows Server 2003. I use a dual network card setup and Routing and Remote Access to link the internal, private network to the external connection. The external connection hooks directly to my cable modem (so no routers or other devices sitting between). The problem I'm having is that I can't connect remotely from a location outside the house (so connecting to the server's external connection) to the server using either Remote Desktop or VNC. I have enabled both ports in Routing and Remote Access's firewall to allow access, and I have enabled Remote Desktop in Windows Server 2003. The odd thing is that I can access my home server's SVN repository and I can even ping the server's IP. I am using the IP to attempt to connect, though I use a dyndns.com provided name to connect to my SVN repository, so it shouldn't make a difference (I know the IP is getting resolved correctly). Any ideas on where to start diagnosing this one? I haven't seen anything in my server's event log. If any other info is needed, let me know. Thanks. UPDATE: One last piece of information: We use a proxy server at work, which I'm nearly 100% sure is the culprit. I have a workaround--if I connect to our VPN (even though I'm already inside the building) I am able to connect to my home server. This is with VNC. However, is there a way to connect through a proxy using Remote Desktop? ONE MORE UPDATE: Indeed, it was the http proxy I'm sitting behind at work that was causing the issue. An acceptable workaround is to use my VPN connection to bypass the proxy, and I'm in!

  Read the article

• Windows 7 wireless not seeing any networks

  - by jkohlhepp

  I think I have managed to confuse Windows 7. When I did the install, I had the network cable plugged in to my router, but the wireless card was also enabled. During the install, Windows 7 seemed to see my wireless network and even asked me for the WEP key. I know that it used the WEP key because I initially entered an invalid one and it gave me an error. Then the network said "SoAndSoWireless Connected". However, when I unplug or disable my wired network card, then I have no internet, and it can't see any networks. When I plug in the wired network card, it says "SoAndSoWireless Connected". Under Network and Internet Network Connections I have "Local Area Connection" and "Wireless Network Connection". The wired one's status is "SoAndSoWireless" and the wireless status is "Not Connected". Also, the wireless connection can't seem to see any other wireless networks in the area and I know there are tons. My neighbors have several. I've somehow seemingly confused Windows 7 into thinking that my wired network card is my wireless card or something. Any ideas on how to un-confuse it? This is a desktop machine by the way, if it matters. EDIT: Ah, I think part of the problem is that I named my network accidentally the same as the name of the wireless network being broadcast by the wireless router. So that might be why it says that name on the hard-wired connection. Perhaps the drivers just are completely not working for the wireless card. Thanks, ~ Justin

  Read the article

• SFTP only works occasionally

  - by 82din

  I suddenly get this error using SFTP: Status: Connecting to example.com... Response: fzSftp started Command: open "[email protected]" 22 Command: Pass: ********* Status: Connected to example.com Status: Retrieving directory listing... Command: pwd Response: Current directory is: "/root" Command: ls Status: Listing directory /root Error: Connection timed out Error: Failed to retrieve directory listing I tried using FileZila, Cyberduck, Shell (Terminal), same result. However, it worked fine today (just a few seconds) in Passive mode. I guess something changed in my network, so I have tried both: Active and Passive mode: Connecting to probe.filezilla-project.org Response: 220 FZ router and firewall tester ready USER FileZilla Response: 331 Give any password. PASS 3.6.0.2 Response: 230 logged on. Checking for correct external IP address Retrieving external IP address from http://checkip.dyndns.org:8245/ Checking for correct external IP address IP <external IP> big-bf-ccc-f Response: 200 OK PREP 49565 Response: 200 Using port 49565, data token 380352881 PORT 186,15,222,5,193,157 Response: 200 PORT command successful LIST Response: 150 opening data connection Response: 503 Failure of data connection. Server sent unexpected reply. Connection closed Because I'm working behind a router, I get my external IP from http://checkip.dyndns.org:8245/ I also tested different range of ports.

  Read the article

• SSRS 2005 inaccessible after install

  - by Gabriel Guimarães

  Hi I've just installed SQL 2005 and Database Engine is ok, however I can't access it for nothing. When I go to http://localhost/reports I get this prompt for a username and password and it fails with 401.1. When I tried to disable kerberos on the virtual directories, nothing changed. I've tried changing the auth to anonymous and get: Internet Explorer cannot display the webpage. When I access from another machine, I get the prompt only once and get this error. Internet Explorer cannot display the webpage. Can't access this with IE or SSMS 2005. If I try to access with Management Studio i get this error: TITLE: Microsoft SQL Server Management Studio The underlying connection was closed: An unexpected error occurred on a receive. (Microsoft.SqlServer.Management.UI.RSClient) ADDITIONAL INFORMATION: Unable to read data from the transport connection: An existing connection was forcibly closed by the remote host. (System) An existing connection was forcibly closed by the remote host (System) BUTTONS: OK By the way the server info: its a Win 2003 R2 Standard with IIS 6 Can't seem to understand this. Does anyone have a hint?

  Read the article

• Setting up vncserver on OpenSolaris zone

  - by k.park

  I am running OpenSolaris 5.10 and set up a sparse zone(inherits most of bin directories from global zone). I ended up copying many etc and var files from global zone, eventually most of the stuff(firefox,gvim, etc.) working through ssh via X11. However, I am having problems setting up vncserver on the zone. This is what I get if I tried to start the vncserver. vncext: VNC extension running! vncext: Listening for VNC connections on port 5911 vncext: created VNC server for screen 0 Fatal server error: could not open default font 'fixed' _X11TransNAMEDOpenClient: Cannot open /tmp/.X11-pipe/X11 for NAMED connection _X11TransOpen: transport open failed for local/%zone%:11 xsetroot: unable to open display '%zone%:11' _X11TransNAMEDOpenClient: Cannot open /tmp/.X11-pipe/X11 for NAMED connection _X11TransOpen: transport open failed for local/%zone%:11 _X11TransNAMEDOpenClient: Cannot open /tmp/.X11-pipe/X11 for NAMED connection _X11TransOpen: transport open failed for local/%zone%:11 _X11TransNAMEDOpenClient: Cannot open /tmp/.X11-pipe/X11 for NAMED connection _X11TransOpen: transport open failed for local/%zone%:11 vncconfig: unable to open display "%zone%:11" twm: unable to open display "%zone%:11" xterm Xt error: Can't open display: %zone%:11 I already chmoded /tmp/.X11-pipe with 777, and there is no pipe in /tmp/.X11-pipe or /tmp/.X11-unix directory. Here is my cat /etc/release: OpenSolaris 2009.06 snv_111b X86 Copyright 2009 Sun Microsystems, Inc. All Rights Reserved. Use is subject to license terms. Assembled 07 May 2009 BRAND: ipkg

  Read the article

• Unable to connect to FTP server using Filezilla with router in-between

  - by pkswatch

  While connecting to my web server using filezilla, i am getting this error: Status: Resolving address of ftp.mysite.org.in Status: Connecting to 199.199.199.18:21... Status: Connection established, waiting for welcome message... Response: 220---------- Welcome to Pure-FTPd [privsep] [TLS] ---------- Response: 220-You are user number 1 of 150 allowed. Response: 220-Local time is now 17:58. Server port: 21. Response: 220-This is a private system - No anonymous login Response: 220-IPv6 connections are also welcome on this server. Response: 220 You will be disconnected after 5 minutes of inactivity. Command: AUTH TLS Response: 234 AUTH TLS OK. Status: Initializing TLS... Error: GnuTLS error -9: A TLS packet with unexpected length was received. Status: Server did not properly shut down TLS connection Error: Could not connect to server I use a cradlepoint CTR35 wifi router to connect to the wired internet connection. When i connect to the same server without this router, the connection works flawlessly. So i guess there is some problem with my router firewall settings, but i dont know what! Can somebody help me out please? Note: The server requires EXPLICIT FTP OVER TLS and does not work with plain FTP sessions. And i can connect to other servers using plain FTP with the router in between.

  Read the article

< Previous Page | 510 511 512 513 514 515 516 517 518 519 520 521  | Next Page >