Search Results

Search found 18786 results on 752 pages for 'edit insanely'.

Page 515/752 | < Previous Page | 511 512 513 514 515 516 517 518 519 520 521 522  | Next Page >

• Intel Atom overheating in ASUS EEE Box 1501P

  - by Sergey L.

  I have had an ASUS EEE Box 1501P for just a little bit over a year. Of course it breaks 2 months after the warranty runs out. http://www.asus.com/Eee/EeeBox_PC/EeeBox_PC_EB1501P/ I have been using the box as a Home Media Center. Running mostly 24/7 often pausing a video overnight. Since last week the fan started running extremely loud. After some digging I found that the Intel Atom CPU in it is overheating and the built-in sensor is reporting temperatures way over 105°C. This got me worried, so I took the unit apart. Completely vacuumed the heat sink, oiled the fan, but the unit is still showing the same behaviour. After turning it on and just observing the hardware monitor in the BIOS the temperature slowly rises from 40°C to over 95°C in appx 5 min. I am running the newest BIOS and a lightweight Linux OPENELEC OS with XBMC on it. Now I am wondering if it could be a faulty heat sensor in the Atom. Recommended running temperature is up to 85°C, but I have not detected any performance hits when running at the above mentioned 105°C and there seem to be no software faults. How can an Atom with an attached heat sink and a fan running at full capacity even get this hot in the first place at 0 load? Aren't those things designed to generate virtually no heat? Could it be a faulty heat sensor? What shall I try to fix this? I would prefer not to damage the CPU, since it is hard fused into the motherboard and cannot be replaced. I could remove the heat pipe/heat sink, but it is getting hot, so heat is properly transferring from the CPU to the heat pipe, the fan is running at full capacity, is recently oiled and warm air is making it out of the exhaust. Edit: One more note: The North-bridge (or whatever it is called nowadays) is on the same heat pipe.

  Read the article

• How do I diagnose a bottleneck in an Intel Atom based Ubuntu server?

  - by Jon Cage

  I have a small media server at home which has software raid and a gigabit link to the rest of my network. For some reason though, I only get ~10MB/s transfers when copying to/from the server. I use software RAID5 (mdadm) over 4 1TB disks. On top of that I then use LVM to give me a huge pool of disk space which is then split up into multiple partitions which can be resized as and when they need it. I'm guessing this it most likely the cause, but I'd like to know for sure where the root cause is. So, how can I benchmark network throughput (Windows 7 desktop <- Ubuntu server) and hard disk performance to try and identify where my bottleneck might be? [Edit] If anyone's interested, the motherboard is an Intel Desktop Board D945GCLF2. So that's a 300 series Atom processor with the Intel® 945GC Express Chipset [Edit2] I feel like such a fool! I just checked my desktop and I had the slower of the two onboard NICs plugged in so the server is probably not at fault here. Transferring a copy of ubuntu off the server I get ~35-40MB/s according to Windows 7. I'll do those HD tests when I get a chance though (just for completeness).

  Read the article

• can not connect to SQL running on amazon ec2 machine

  - by njj56

  I am using SQL managment studio 2008 running on an Amazon EC2 machine. I am unable to connect to the database in my asp.net application. The EC2 instance has been set to accept connections over the SQL port. I am also able to remote the machine as well as view websites hosted on the server. Listed below is part of the connection string relating to this instance. When the program is ran and this connection string is called, it returns tcp error 0 - no return response. it just times out. <add name="ProjectServer" connectionString="Data Source=*IP ADDRESS HERE*,1433;Initial Catalog=*Catalog Name*;User ID=IP-0A6ED514\Administrator;"/> I removed the ip and the catalog name for the example, but I am sure they are correct. The only thing that I could think may cause an error, is the differences in names between the user id and the server name - the server name is ip-0A6ED514\sharepoint but the user name is ip-0A6ED514\administrator when I log into the sql server manager on the EC2 instance. A password is not used. Not sure if I would need to leave in a blank string for password - also not sure if the difference between server name and user id to log in makes a difference. Any help is appreciated. Thank you. update - when this connection string is used with out the port, i get tcp provider error 40 - when the port is in there, i get error 0 edit- the sql server is using windows authentication - does this make a difference? Usually I always use SQL server authentication

  Read the article

• DNS Resolution doesn't work after uninstalling Cisco VPN & Deterministic Network Enhancer in Win 7

  - by Craig M

  I just upgraded my home PC to Windows 7 Ultimate 32 bit. After trying various methods to get the Cisco VPN client to work, I gave up and decided to just run it in XP mode. The last steps I tried were in this article ( http://social.technet.microsoft.com/Forums/en-US/w7itproappcompat/thread/d880dfe5-7f44-4955-8620-2a9355d8ea8b/ ) After that, I uninstalled the Cisco client and rebooted. I uninstalled the Deterministic Network Enhancer and rebooted again. Both uninstalled successfully, but now I'm not able to resolve any DNS. The only way I can resolve DNS is to reinstall the DNE, reboot, and uninstall the DNE. Then I am able to resolve DNS lookups until I reboot again. Once it's rebooted, no more DNS. Any ideas? Edit: I completely forgot I'd asked this question until harrymc posted his answer. I've since found out that to fix this problem, I need to disable my Local Area Connection and re-enable it. Once I do that I have no trouble making network connections until the next time I reboot at which point I repeat the process. It's annoying, but manageable since I reboot very infrequently.

  Read the article

• Configure an Azure VM for Dynamic DNS for Cloud Services

  - by Adam

  I am trying to setup an azure VM with proper DNS to allow multiple cloud services to communicate across cloud service boundaries. As I understand it, I need to provide my own DNS server. I do not have any on-premise infrastructure, so I am trying to configure an Azure VM to act as my DNS. This SO question (http://stackoverflow.com/questions/21858926/azure-how-to-connect-one-cloud-service-with-other-in-one-virtual-network) is very similar to my setup. This article (http://msdn.microsoft.com/en-us/library/windowsazure/jj156088.aspx) describes my particular case: Name resolution between virtual machines and role instances located in the same virtual network, but different cloud services Here is what I have done: Created Azure Virtual Network and declared subnets for each of my cloud services. Created an Azure VM (Windows 2012 R2) with DNS enabled RDP to the VM and enabled the DNS role and installed features Added the appropriate NetworkConfiguration xml section to each of my cloud services .csfg files Re-deployed my cloud services I have verified that I setup the virtual network and networkconfiguration properly because my cloud service hosts are able to communicate with each other if I use the internal ips. However, name resolution doesn't appear to be working, and it doesn't appear that my cloud service roles can communicate with my DNS server. How do I configure my VM so that my different cloud services roles register themselves with my DNS server? EDIT: I think I am 1 step closer to getting this to work. The cloud services that I was using are in an old affinity group which is not supported by VMs, so I was unable to add my VM into my virtual network. I created a new VNET in a new affinity group with my VM added into it. However, I still don't know how to configure the azure VM's DNS server so that the cloud services register themselves for name resolution. Also, an added bonus guaranteed to get a +1 would be to explain if it is possible to register a DNS entry for the VIP for an internal endpoint of my cloud services so we can get load balancing. Thanks!

  Read the article

• Linux Mint 13 is not booting on dual boot computer

  - by Brian

  thanks in advance for your time. I have 2 hard drives in my computer a 300 GB drive which is my primary drive for windows 7 and a 1.5 TB drive that I'd used for storage. When I got it I partitioned 500 GB for use in Linux. So, I created a bootable USB and clicked the "Install by Current Operating System" option from Mint. It installed it to the free 500 GB like I'd hoped it would. Now, I can't get it to boot though. I've tried using EasyBCD to create the boot entry and it hangs on a black screen. Thanks. EDIT @ Ryhuk It presents a menu with two options 1) Windows and 2) Mint. This was a menu I created with easyBCD. When I select option 1 it boots to windows fine. When I select option 2 it hangs on a black screen with just a white bar flashing (Can't remember what its called, it marks the current cursor location on a text field) and won't respond to any key presses but alt ctrl del.

  Read the article

• Configuring vlans on Cisco SG200 series switch with Ubuntu server

  - by nixnotwin

  I created a vlan on Ubuntu with vconfig tool with 21 as id and eth1 as the host port. I connected eth1 to one of the ports on the swtich (GE23) as all ports trunk by default. In the webgui I created a vlan named test with the id 21 and I made GE2 are port as an access port. In port to vlan mapping I selected vlan 21 and added it port GE2 by selecting untagged option. I have assigned 192.168.1.1/24 as the ip of eth1.21 on Ubuntu. If I connect another cleint pc to GE2 port with a ip of 192.168.1.2/24 I cannot ping the server ip (192.168.1.1/24). Ping from server to client also does not work. I inspected packets that are sent out eth1 on the server and I could see the vlan 21 tag. And I connect the other end of the cable to a different Linux pc and inspected the packets but no vlan tags can be seen. What could be preventing me from getting vlans working? Edit 1 screenshots:

  Read the article

• Server Restart's and Respective Orders

  - by TheD

  EDIT:Not meaning to be disrespectful to any of the answers, but, the main question was whether rebooting a DC at the beginning of a cycle, then all the other servers, or rebooting it at the end once all the others are back online - is there a reason for doing it either way? I'm still not sure based on current responses. This will most likely seem like a fairly, maybe even stupid, question, but it's something I have been wondering about. As part of a regular process for clients servers are restarted remotely after patches and every client tends to have a similar order - but there always seems to be a small debate when it comes down to when do you reboot your DC. For example, 4 servers, 1 DC, 1xExchange, 1xBESX and 1xRandom, lets say it has some CRM software installed, is it best to reboot the DC first, then Exchange, then BESX and so on - or reboot all the servers, then reboot the DC last? - Perhaps it doesn't matter at all and it's just a case of how you have always done it. Would it change in a Hyper-V environment for example, with a physical DC, 1 VHost with all your servers virtualised on that Host? Rebooting the VHost and Virtual Machines first, then the DC at the end, or vice versa? Thanks!

  Read the article

• Data recovery on a data HDD (no OS)

  - by aCuria

  I am helping a family member with a dead hard disk. It is a seagate 200Gb 3.5" HDD in one of those old-school external enclosures. The problem was that windows failed to detect the hard disk when plugged in through USB. I removed the hard disk from its enclosure, and plugged it into my desktop PC. The BIOS does detect it upon POST, but unfortunately windows 7 would refuse to boot. It will get stuck on the loading screen with the glowing windows logo. Safe mode doesn't help either. What options do I have before going for some professional data recovery? edit: Someone modified the Title to something completely different from what I was asking, i just changed it back. 1) 2 HDD drives, DiskA(Dead), DiskB(my OS disk) 2) when B is connected to my system, everything works fine 3) when A AND B is connected, failure to boot. POSTs fine, but windows wont load 4) A has NO OS, its PURE data. It came from an EXTERNAL HDD enclosure which doesnt belong to me, and im trying to do data recovery.

  Read the article

• Cannot send email outside of network using Postfix

  - by infmz

  I've set up an Ubuntu server with Request Tracker following this guide (the section about inbound mail would be relevant). However, while I'm able to send mail to other users within the network/domain, I cannot seem to reach beyond - such as my personal accounts etc. Now I have no idea what is causing this, I thought that all it takes is for the system to fetch mail through our exchange server and be able to deliver in the same way. However, that hasn't been the case. I have found another server setup in a similar fashion (CentOS 5, Request Tracker but using Sendmail), however it is a dated server and whoever's built it has kindly left no documentation on how it works, making it a pain to use that as a reference system! :) At one point, I was told I need to set up a relay between the local server's email add and our AD server but this didn't seem to work. Sorry, I know next to nothing about mailservers, my colleagues nothing about Linux so it's a hard one for me. Thank you! EDIT: Result of postconf -N with details masked =) alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 mydestination = myhost.mydomain.com, localhost.mydomain.com, , localhost myhostname = myhost.mydomain.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relayhost = EXCHANGE IP smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes Sample log message: Sep 4 12:32:05 theedgesupport postfix/smtp[9152]: 2147B200B99: to=<[email protected]>, relay= RELAY IP :25, delay=0.1, delays=0.05/0/0/0.04, dsn=5.7.1, status=bounced (host HOST IP said: 550 5.7.1 Unable to relay for [email protected] (in reply to RCPT TO command))

  Read the article

• Accounting setup in freeradius with mikrotik and the "always" module

  - by Matt

  I have a freeradius setup that is being used to provide authentication for users on a wireless network. The access points are all Mikrotik hardware and the users are connected 24/7. We've been using Daloradius with mysql and freeradius 2. The boss wants to use the accounting information and while this is all set up and appears to be working, I've found that not all the accounting information is present. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly. So he started poking around at this link: http://wiki.mikrotik.com/wiki/RouterOs_MySql_Freeradius#Configuring_RouterOs_for_Radius_.26_PPP.2A_AAA And was looking specifically at the following section. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly always fail { rcode = fail } always reject { rcode = reject } always ok { rcode = ok simulcount = 0 mpp = no } However, that link references freeradius 1 and I can't find this in the radius.conf file for freeradius 2. What does it do and could it be a reason I'm missing data? EDIT: I have found one issue. We have a backup freeradius server that is also receiving the accounting packets. Although they are replicating, it's only a master/slave configuration. If the slave receives accounting packets it won't replicate them back to the master. Although I suspect this might solve it, the boss is not convinced due to the always module. Is there anything special I need to configure in the mikrotik AP's or freeradius 2 for clients connected 24/7.

  Read the article

• running automated fsck on remote server

  - by GriffinHeart

  I had another question about df, and now i came to conclusion i need to run fsck my partition, i've been reading about it and would like some advice, if possible. The situation is like this, no physical access to the server and i want to run fsck. from what i read i just need to touch /forcefsck and when i reboot it will run fsck. My question is, at its basis, with what arguments will the fsck run? Will it need user input to correct errors, etc? and after running will it save a log of what happened? if this was how it ran it would be perfect, anyway of enforcing that on reboot? fsck -v -p /machine/disk/p1 2>&1 > fscklog.txt Also here they describe this: it's also a good idea on debian and debian-derivatives like ubuntu to edit /etc/default/rcS on remote servers and set "FSCKFIX=yes" that adds "-y" to the boot time fsck, so it doesn't risk the remote server being stuck waiting for someone to login at the console and run fsck. But on Centos that doesn't seem to exist I only have ssh access at the moment so that is why i'm being so picky with it. here's some info about disks and mounted volumes on the server: http://pastebin.centos.org/33314 Thanks.

  Read the article

• scp No such file or directory

  - by Joe

  I've a confusing question for which superuser doesn't seem to have a good answer, and neither google. I'm trying to scp a file from a remote server to my local machine. The command is this scp user@server:/path/to/source/file.gz /path/to/destination The error I get is: scp: /path/to/source/file.gz: No such file or directory user is my username on the server. The command syntax appears fine to me. ssh works fine and I can cd to the file and it doesn't seem to be an access control issue? Thanks; Edit: Thank you John. I spotted the issue. ls returned this: -r--r--r-- 1 nobody users 168967171 Mar 10 2009 /path/to/source/file.gz So, the file was on a read-only file system and user is able to read it but not scp. I just copied the file to a different directory and chown it and worked fine. It would be good if someone can explain why this is the case though.

  Read the article

• Reconfiguring, then deleting obsolete pagefile.sys from C: in one go using a batch script

  - by DanielSmedegaardBuus

  I'm trying to set up an automated script for a Windows XP installer. It's a batch script that runs on first boot after installation, and among the things I'm trying to accomplish, is removing the pagefile from C: entirely, and putting a 16-768 MB pagefile on D: instead. Here're my batch file instructions: echo === Creating new page file on D: ... cscript %windir%\system32\pagefileconfig.vbs /create /i 16 /m 768 /vo d: >nul echo. echo === Removing old page file from C: ... cscript %windir%\system32\pagefileconfig.vbs /delete /vo C: attrib -s -h c:\pagefile.sys del c:\pagefile.sys My problem is that while these are sane commands, the removal of the pagefile on C: requires me to reboot before those commands succeed.b Or, in other words — I have to first create the D: pagefile, then reboot and delete the c:\pagefile.sys file, or I'm stuck with a c:\pagefile.sys file which isn't even recognized by Windows itself (it'll just say that there's a page file on D:, and that C: has no pagefile at all). Obviously because already some pages are written to the C:\pagefile.sys file. So how would I go about accomplishing this in one go? Or, in two gos, if this is "batch scriptable" :) TIA, Daniel :) EDIT: I should probably clarify: Running those commands above are all valid, but they'll only succeed fully if I re-run the "attrib" and "del" commands at next boot. The C: pagefile is in use at the time, so I cannot delete the file it uses, and Windows itself won't remove it when I configure it to not use C: as a page file drive. Instead, it'll leave an orphaned c:\pagefile.sys file behind (which is really large). I don't necessarily need this to work in one go, registering the last two commands to run after a reboot would also be great :)

  Read the article

• Mysql server won't start - no logs

  - by Owen

  After a restart, mysql won't start. sudo service mysql start gives start: Job failed to start and the logs are empty, so I have no idea where to start. I'm pretty sure permissions problems are taken care of. Edit: All disks have at least 1G of space and sh -x /etc/init.d/mysql start gives me: + set -e + basename /etc/init.d/mysql + INITSCRIPT=mysql + JOB=mysql + [ mysql = upstart-job ] + [ -z start ] + COMMAND=start + shift + [ -z ] + ECHO=echo + echo Rather than invoking init scripts through /etc/init.d, use the service(8) Rather than invoking init scripts through /etc/init.d, use the service(8) + echo utility, e.g. service mysql start utility, e.g. service mysql start + echo + echo Since the script you are attempting to invoke has been converted to an Since the script you are attempting to invoke has been converted to an + echo Upstart job, you may also use the start(8) utility, e.g. start mysql Upstart job, you may also use the start(8) utility, e.g. start mysql + grep -q start/ + status mysql + [ -z ] + [ start = stop ] + [ -n ] + start mysql start: Rejected send message, 1 matched rules; type="method_call", sender=":1.105" (uid=1000 pid=3208 comm="start mysql ") interface="com.ubuntu.Upstart0_6.Job" member="Start" error name="(unset)" requested_reply="0" destination="com.ubuntu.Upstart" (uid=0 pid=1 comm="/sbin/init")

  Read the article

• Apache directive for authenticated users?

  - by Alex Leach

  Using Apache 2.2, I would like to use mod_rewrite to redirect un-authenticated users to use https, if they are on http.. Is there a directive or condition one can test for whether a user is (not) authenticated? For example, I could have set up the restricted /foo location on my server:- <Location "/foo/"> Order deny,allow # Deny everyone, until authenticated... Deny from all # Authentication mechanism AuthType Basic AuthName "Members only" # AuthBasicProvider ... # ... Other authentication stuff here. # Users must be valid. Require valid-user # Logged-in users authorised to view child URLs: Satisfy any # If not SSL, respond with HTTP-redirect RewriteCond ${HTTPS} off RewriteRule /foo/?(.*)$ https://${SERVER_NAME}/foo/$2 [R=301,L] # SSL enforcement. SSLOptions FakeBasicAuth StrictRequire SSLRequireSSL SSLRequire %{SSL_CIPHER_USEKEYSIZE} >= 128 </Location> The problem here is that every file, in every subfolder, will be encrypted. This is quite unnecessary, but I see no reason to disallow it. What I would like is the RewriteRule to only be triggered during authentication. If a user is already authorised to view a folder, then I don't want the RewriteRule to be triggered. Is this possible? EDIT: I am not using any front-end HTML here. This is only using Apache's built-in directory browsing interface and its in-built authentication mechanisms. My <Directory> config is: <Directory ~ "/foo/"> Order allow,deny Allow from all AllowOverride None Options +Indexes +FollowSymLinks +Includes +MultiViews IndexOptions +FancyIndexing IndexOptions +XHTML IndexOptions NameWidth=* IndexOptions +TrackModified IndexOptions +SuppressHTMLPreamble IndexOptions +FoldersFirst IndexOptions +IgnoreCase IndexOptions Type=text/html </Directory>

  Read the article

• Linux Sound Drivers - Recompiling kernel with ehcd-hcd module

  - by jhome

  I just installed Linux Mint and I am trying to get my usb soundcard to work. I am completely new to Linux so I have only been learning about all the important parts of the OS this afternoon. No one I know has compiled kernel so I can't ask anyone. I am following instructions on this site: http://wiki.ubuntuusers.de/Benutzer/BigMc#Final-setup-of-US-122L-US-144 "Recompile your Kernel with ehcd-hcd as a module: Instructions for Ubuntu (german) Change "Device Drivers - USB support - EHCI HCD (USB 2.0) support)" to "M" when configuring. Make sure you also install the kernel headers." I know how to do any of these processes. Someone mentioned a package manager. Is recompiling basically in layman's terms reinstallation? Where do I go to the change device drivers? Cheers Edit: I am attempting to be able to use my Tascam US-144 on Linux Mint. Apparently, to use it properly it has to regress to functionality of a former unit (US-122), so according to the instructions a USB port has to be USB 1.0, rather than USB 2.0. I've tried using that ndis** programme for wireless drivers but with no success.

  Read the article

• Block protect (Keep last line of paragraph with next paragraph)

  - by Ed Cottrell

  Is there a way to force Microsoft Word 2010 to keep the last line of a paragraph with the next paragraph? An example of when this is relevant is when starting a block quote; it doesn't look good to have the block quote start at the top of a new page, particularly when it's introduced by a partial sentence, like this: "Lorem ipsum" is sample text widely used in the publishing industry, as the text has spacing roughly similar to that of English and therefore looks "normal" but unintelligible to an English reader's eye, allowing the reader to focus on design elements. It begins, Lorem ipsum dolor sit amet, consectetur adipiscing elit. Nam rhoncus laoreet risus, quis congue leo viverra congue. Suspendisse magna massa, viverra imperdiet est eu, ultrices volutpat lectus. Sed pulvinar est id risus lobortis venenatis. There shouldn't be a page break after "begins," because it looks like the sentence ends abruptly. "Keep lines together" won't work, because by definition we're talking about two paragraphs. "Keep with next" won't work if the first paragraph is larger than a couple of lines, because then you get an awkwardly large space at the bottom of a page. Manual line breaks obviously work, but only when the document is final, which is often less certain than it seems. I know WordPerfect has a feature called "block protect" that does this, but I have not found even an acceptable substitute in Word. I have played with style separators and hidden paragraph breaks, but to no avail. I would love a special character, kind of like the nonbreaking space or zero width optional space, that tells Word to move to the next page if the next paragraph would otherwise start the page. A macro would also be great, but I haven't been able to find a starting point (like how to detect where non-manual page breaks fall). Edit: It looks like "Keep with next" works this way in Word 2013, but I specifically need a fix that works in Word 2010.

  Read the article

• 554 5.7.1 <mail_addr>: Relay access denied centos postfix

  - by Relicset

  I have problem in send mail from postfix in centos I have following setup mail server postfix for sending mail but I am getting error. As in the link I tried following commands telnet localhost smtp Trying ::1... Connected to localhost. Escape character is '^]'. 220 mydomain.com ESMTP Postfix ehlo localhost 250-mydomain.com 250-PIPELINING 250-SIZE 10240000 250-VRFY 250-ETRN 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN mail from:<domain.com> 250 2.1.0 Ok rcpt to:<[email protected]> 554 5.7.1 <[email protected]>: Relay access denied Edit-1 In terminal this works echo TEST | mail -v -s "Test mail" [email protected] my postconf -n shows belog information alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix debug_peer_level = 2 home_mailbox = Maildir/ html_directory = no inet_interfaces = localhost inet_protocols = all mail_owner = postfix mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man mydestination = $myhostname, localhost.$mydomain, localhost, $mydomain mydomain = dummy.com myhostname = dummy.com mynetworks = all mynetworks_style = host myorigin = $mydomain newaliases_path = /usr/bin/newaliases.postfix queue_directory = /var/spool/postfix readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES sample_directory = /usr/share/doc/postfix-2.6.6/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop unknown_local_recipient_reject_code = 550 What configuration I have to perform to send mails from my server.

  Read the article

• Find out the type of an automounted device

  - by Steve Bennett

  I'm working on a system (Ubuntu Precise) with a mount defined in /etc/fstab as follows: /dev/vdb /mnt auto defaults,nobootwait,comment=cloudconfig 0 2 Originally I just wanted to find out if it's NFS (due to potential MySQL locking issues). Judging from man mount, it's not: If no -t option is given, or if the auto type is specified, mount will try to guess the desired type. Mount uses the blkid library for guessing the filesystem type; if that does not turn up anything that looks familiar, mount will try to read the file /etc/filesystems, or, if that does not exist, /proc/filesystems. All of the filesystem types listed there will be tried, except for those that are labeled "nodev" (e.g., devpts, proc and nfs). If /etc/filesystems ends in a line with a single * only, mount will read /proc/filesystems afterwards. But, out of curiosity now, how can I find out more about what type of device it actually is? (For context, this is a VM running on OpenStack. The device is a 60Gb allocation mounted from somewhere - but I don't know how.)` EDIT Including answers here: $ mount /dev/vdb on /mnt type ext3 (rw,_netdev) $ df -T /dev/vdb ext3 61927420 2936068 55845624 5% /mnt

  Read the article

• How can I debug user mode driver failures in Windows 8

  - by Tom

  I have a 32 GB SD Card. Whenever I insert this card in to my newly upgraded Windows 8 laptop the OS stops responding normally. Metro Apps won't work. The system may or may not log in. Desktop apps may or may not be able to do things. When I remove the card and restart then all is fine. As soon as I put the card back in, the system starts misbehaving again. I've run Windows Update, so I have the latest drivers from Microsoft. This does not occur with the 8 GB cards I have. Unfortunately I only have one 32 GB card, so I can't test with others. From examining the system event log I've determined this is happening due to a user mode driver failure. How can I best debug this issue from here? How can I figure out which driver this is related to? Will there be a Dr. Watson crash dump somewhere? Details - System - Provider [ Name] Microsoft-Windows-DriverFrameworks-UserMode [ Guid] {2E35AAEB-857F-4BEB-A418-2E6C0E54D988} EventID 10110 Version 1 Level 1 Task 64 Opcode 0 Keywords 0x2000000000000000 - TimeCreated [ SystemTime] 2012-10-29T00:51:57.532718300Z EventRecordID 40417 Correlation - Execution [ ProcessID] 1056 [ ThreadID] 3796 Channel System Computer thebrain - Security [ UserID] S-1-5-18 - UserData - UMDFHostProblem [ lifetime] {811E3DC4-FBC6-420B-ABCC-AD7505A36F3B} - Problem [ code] 3 [ detectedBy] 2 ExitCode 3 - Operation [ code] 259 Message 72448 Status 4294967295 Edit 1 So I tried using Debug View from SysInternals (you can get it here: http://technet.microsoft.com/en-us/sysinternals/bb896647.aspx). That gave me this information: which is not especially helpful. Then I tried connecting WinDbg to WUDFHost.exe (the process that seems to host user mode drivers) to see if it could catch the error. Get it here: http://msdn.microsoft.com/en-US/windows/hardware/hh852363 Instructions: http://msdn.microsoft.com/en-US/library/windows/hardware/ff554716(v=vs.85).aspx That didn't help much. It didn't catch any exceptions as I'd hoped (which would point me to the cause of the crash at least). Here's the stack of one of the threads:

  Read the article

• Windows Server 2008 R2 install reboots unexpectedly during "Completing installation" phase

  - by knda

  I am attempting to install Windows Server 2008 R2 onto a Cisco UCS C201 M2 rack mounted server but am having major difficulties and wondering if anyone has some insight or items they could recommend for me to look at to get this one resolved. Installation is being attempted via the Cisco remote console (using CIMC's Virtual dvd-rom).. following the first phase of Setup where the installation files are copied to the target hard drive, then a reboot occurs to load Setup from the HDD, mid-way in the "Completing Installation" phase the system then reboots unexpectedly. System configuration Cisco UCS C201 M2 (2RU rack mounted server) 16GB RAM, 2x 73GB 15K SAS, 4x 300GB 10k SAS Add-on cards - Intel quad-port GigE card (no fibre channel cards) Storage - LSI MegaRAID SAS 9261-8i. onboard SATA is disabled (no SATA drives connected) KVM - Belkin No physical DVD-ROM.. :( I have... Run memtest86+, no RAM faults Disabled/enabled SATA support (BIOS) Attempted install from USB DVD-ROM, no effect Attempted unattended install scripted via Cisco Configuration Manager DVD provided Removed Belkin KVM in case that was causing drama Discovered that the Cisco website is "awesome" for searching for PDFs/Drivers cough, reverted back to Google Downloaded latest LSI drivers from LSI's site and used during Server 2008 install checked Windows ISO against checksum's from MS site checked Windows ISO by using it for an install in a VM Running out of ways to troubleshoot this as I am not sure how to enable any sort of 'verbose' mode during the setup process. Next step I have planned is to remove the Intel NIC and try the installation again.. Edit: Problem was the "Cisco INTEL QUAD PT GBE" (1000/PT) .. will have to see if this card is faulty or if it's just drivers.. thanks for the help.

  Read the article

• Why my 2nd ip from traceroute is not answering the ping anymore?

  - by Pedro77

  My Internet is really laggy today, I did a tracerout and I realize that I'm having no answer from an ip at the beginning of the traceroute. see: Tracing route to 12.129.202.154 over a maximum of 30 hops 1 <1 ms <1 ms <1 ms 192.168.0.1 2 * * * Request timed out. 3 8 ms 8 ms 8 ms bd044008.virtua.com.br [189.4.64.8] 4 9 ms 8 ms 8 ms bd044009.virtua.com.br [189.4.64.9] 5 26 ms 26 ms 24 ms embratel-T0-1-5-0-tacc01.cas.embratel.net.br [200.174.243.21] 6 360 ms 15 ms 12 ms ebt-T0-15-0-12-tcore01.ctamc.embratel.net.br [200.244.140.218] 7 330 ms 349 ms 261 ms ebt-Bundle-POS11942-intl04.mianap.embratel.net.br [200.230.220.10] 8 139 ms 141 ms 139 ms sl-st30-mia-.sprintlink.net [144.223.64.221] Connection diagram: PC - Router configured as access point - Router (192.168.0.1) - Cable modem (192.168.100.1). Well, I think it is odd that the 2nd ip is not returning the ping. I looked some old tracerout logs to see what was the 2nd ip. The ip was: 10.19.0.1 So, what this 2nd ip stand for? How can I find why it is not answering the ping? I don't understand it, if does not answer the ping, how can the packets continue (yeah newbie question)? edit: well, because the hope 3 have a ping of 8 ms the hop 2 request time out should really not be a problem. But it is still odd that the 2nd hop stopped to answer ping request. So my doubts are: 1. Were the ip 10.19.0.1 is from? 2. Why it stopped to answer ping requests? 3. How can hop 7 be smaller than 6 and 8 smaller than 7 and 6!?? Shouldn't the pings be higher for each hop? Like: hop 3 time should be the sum of the hops before it plus its own time (hop 3 = 1+2+3) ??

  Read the article

• 1 document pending in printer queue in System Tray that won't go away

  - by White Phoenix

  Edit: I didn't want to do it, but I restarted my computer - cleared the problem right away. Though if I were running a Windows 2003/2008 server, I would hate to have to restart the domain controller just to get rid of this irritating problem. If I run into this problem again, I'm going to try that remove printer/reinstall printer thing. Thanks for your help @Psychogeek. Points for your attempt. Running Windows 7, 32-bit Professional. My printer is an HP OfficeJet Wireless 8500. It's connected to my network wirelessly through TCP/IP as a standalone device. I was having some print problems awhile back and had to do some print spooler stuff as part of my troubleshooting (stopping the Print Spooler service, clearing the print spooler files from C:\Windows\System32\spool\PRINTERS and then restarting the service). I've finally narrowed it down to it being application specific, so that's that. However, as a leftover from all that troubleshooting, my printer icon is stuck in the tray - when I mouseover the icon, Windows says that there is 1 document(s) pending for my username. However, when I open up that printer's queue, there's nothing in there. I restarted the Printer Spooler service and also checked C:\Windows\System32\spool\PRINTERS if there's anything in there - nothing. I did a quick Google search and an answer from one of those "reps" at the Microsoft Socialnet site says for me to uninstall and reinstall the printer. The funny thing is, when I send print jobs, they print just fine - that 1 mystery document stuck in queue isn't stopping anything from happening. Short of having to do that, are there any other quick troubleshooting steps I may be missing?

  Read the article

• Shared printer stops working on clients but not host computer

  - by Tony

  I have a Brother MFC-7420 USB all-in-one laser printer. It is plugin via USB to my Windows 7 x64 machine. I have it shared to a few users on my home network. My wife's laptop running Vista x64 can normally print fine to the printer. However it seems that every day or two, when she pushes print on a something it just sits in her laptop's print queue and never makes it to my desktop. The only thing that seems to fix this is if she restarts her laptop. Not a big deal but this problem is sort of annoying. I don't know if this affects but the laptop is put into hibernate at night and I turn my desktop off at night. Does anyone know why this happens and if there is something easy to do to fix the problem besides restart the computer? EDIT: I was thinking that maybe my wife's laptop loses its connection to the printer. Is there a way to reset a connection to a shared printer? Or maybe reauth with the printer?

  Read the article

< Previous Page | 511 512 513 514 515 516 517 518 519 520 521 522  | Next Page >