Search Results

Search found 19009 results on 761 pages for 'network shares'.

Page 515/761 | < Previous Page | 511 512 513 514 515 516 517 518 519 520 521 522  | Next Page >

• Linksys WRT54G2 not showing connected PC's in DHCP table

  - by Moose

  For some reason all of a sudden my linksys WRT54G2 no longer shows PC's connected in the DHCP table. It was being touchy then all of a sudden they all just disappeared. It showed 2 of the 4 connected then it showed the other 2 then it only showed 1 and then it was showing none. I seem to be having a connection reset every 30-60 minutes also not sure if that is related to the router going bad or if it is just comcast being it's typical crappy self. I have tried to reset my router and my cable modem and both problems still seem to keep happening(no PC's in table and connection reset every 30-60 mins). Now I know the router doesn't store clients after a router reboot but they normally show up within a matter of minutes for me in the past. Before anyone asks yes all devices on the network are using DHCP and not static. Could this be a sign of the router starting to go bad?

  Read the article

• allowing 2 VM's to communicate RED HAT 64 bit

  - by ????? ????????

  My physical PC is running 2 VMs on virtualbox. Both of the VM's are linux 64 bit. I am going through this tutorial: http://www.cyberciti.biz/faq/rhel-centos-fedoracore-linux-network-card-configuration/ in order to expose both of their IP's so that they can speak to each other. Mike Schwager November 25, 2009 at 10:55 pm Whoops! In section 3, you forgot about editing /etc/hosts. I believe RedHat comes complete with the system’s host ip address set up in /etc/hosts. Don’t forget to give it a look. I agree with Mike because after I looked into the /etc/hosts files, it has just default localhost stuff in it. How should I reconfigure the hosts file?

  Read the article

• Path of md device wrong after reboot

  - by flammi88

  I have to set up a software raid (level1) on a Ubuntu server 12.04. It should serve files in the network via Samba. The server has the following disks: 250gb Sata hdd (Ubuntu is installed on that drive) 2 TB Sata hdd (first disk in raid array, data disk) 2 TB Sata hdd (second data disk) I created one partition on every data disk with the type Linux raid autodetect. In the second step I created the raid1 with the following command: mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/sdb1 /dev/sdc1 After that, I added the array to the mdconf: mdadm --examine --scan >> /etc/mdadm/mdadm.conf The problem is: After a reboot the array is not available on the path /dev/md0. Instead of that it gets reassembled as /dev/md/0 but it is not very reliable. Has anybody a solution for this issue?

  Read the article

• NetBeans Podcast #58

  - by TinuA

  Download mp3: 52 minutes – 44.1 MB Subscribe to the NetBeans Podcast on iTunes NetBeans Community News with Geertjan and Tinu NetBeans IDE 7.1 Release Candidate 1 Download the release candidate build Is NetBeans IDE 7.1 release ready? Give your feedback in the NetBeans Community Acceptance Survey. (Survey deadline is Wednesday, December 7th.) NetBeans Governance Board: Term 19 Sven Reimers is voted in for a second term; Zoran Sevarac is the newbie on the board; and John Jullion Ceccarelli continues as the Oracle representative.  NetBeans Calendar Community Interview: Sven Reimers Software architect and NetBeans Dream Team member Sven Reimers joins Geertjan for a recap of highlights and hot topics from Devoxx 2011. Also covered: His re-election to the NetBeans Governance Board. NetCAT 7.1 Report with Jirka Kovalsky The NetCAT program (NetBeans Community Acceptance Testing) is a customary part of the NetBeans release cycle, giving users the opportunity to help test and get the NetBeans IDE release ready. Program manager Jirka Kovalsky reports back on how the team for 7.1 fared. API Design with Jarda Tulach Jarda has a new API Design book coming out! Visit his API Design site for details. Community Interview: Zoran SevaracZoran Sevarac has an impressive profile: Founder of the open-source project Neuroph, a Java frameworks for neural network development; software engineering teaching assistant; founder of the first NetBeans User Group in Serbia; artificial intelligence researcher; NetBeans Platform Certified trainer; new member of the NetBeans Governance Board. Zoran takes a break from his busy(!) schedule to chat about his experience using NetBeans technology, his efforts to educate the local developer community about Java and NetBeans, as well as his newest role in the NetBeans Community. Neuroph: Smart Java Apps with Neural Networks (Dzone article) More DZone articles about Neuroph and NUG Serbia Have ideas for NetBeans Podcast topics? Send them to nbpodcast at netbeans dot org.

  Read the article

• Accessing IPv6 router interface from a minimal Fedora installation?

  - by Zack

  I've recently installed Fedora 16 and am trying to set up a simple apache server. The only problem I've run into so far is that I'm unable to access my router's web interface from any box on my network. It assigns addresses via dhcp, and the router always responds to a ping. The server is also picking up an IP from the router on the proper subnet. Now, all I really need to do is forward a port, however I am receiving "Unable to connect" through the web interfaces and "connection refused" via telnet. What are my options, and how might I go about troubleshooting this? Will I need the server's ip to be static in order to change these settings? The router is a "Netopia" model, if that helps.

  Read the article

• FotoJeff.com | My Photography Blog

  - by Jeff Julian

  I have been recently been doing more photography and Flickr was only allowing me to do so much with the images in displaying them.  No customization of skin, no page grouping, no post like pages.  So I decided to host a WordPress blog to host my images.  I really wanted to try WordPress to see what features single-hosted blog products offer that our multiple-hosted blog system could take advantage of.  So far the product is very cool, I can see how such a large developer network would help produce such cool “apps” for WP.  The product makes if very easy to make changes to your hosted environment that would be a little scary for a multiple blog host.  I need to compare features for their hosted solution. Any who, FotoJeff.com is my new photography blog home.  I have been working with the Kansas City Rescue Mission a lot lately so most of my shots are for them. FotoJeff.com – Photography Blog of Jeff Julian My hope is to make this blog again my technology blog, Staff of Geeks our Geekswithblogs.net announcement blog and FotoJeff.com my photography blog.  I need to start dog fooding my thoughts on blogging and keep the noise down (by making more noise with this post :D). Technorati Tags: FotoJeff.com,Photography,Blogs,Geekswithblogs

  Read the article

• Windows Azure Virtual Machine Test Drive Kit

  - by Clint Edmonson

  The public preview of hosted Virtual Machines in Windows Azure is now available to the general public. This platform preview enables you to evaluate our new IaaS and Enterprise Networking capabilities. Once you have registered for the 90 Day Free Trial and created a new account, you can access the preview directly at this link: https://account.windowsazure.com/PreviewFeatures If you’ve been to any of my presentations lately, you’ll know that I’m fired up about these new offerings. As I’ve worked through some scenarios for myself and with my customers, I’ve been collecting the resources that helped me to ramp up. Here’s a collection of links to the items I’ve found most useful: Core Resources Digital Chalk Talk Videos – detailed technical overviews of the new Windows Azure services and supporting technologies as announced June 7, including Virtual Machines (IaaS Windows and Linux), Storage, Command Line Tools http://www.meetwindowsazure.com/DigitalChalkTalks Scenarios Videos on You Tube – “how to” guides, including “Create and Manage Virtual Networks”, “Create & Manage SQL Database”, and many more http://www.youtube.com/user/windowsazure Windows Azure Trust Center - provides a comprehensive of view of Windows Azure and security and compliance practices http://www.windowsazure.com/en-us/support/trust-center/ MSDN Forums for Windows Azure http://www.windowsazure.com/en-us/support/preview-support/ Microsoft Knowledge Base article Microsoft server software support for Windows Azure Virtual Machines Videos Deep Dive into Running Virtual Machines on Windows Azure Windows Azure Virtual Machines and Virtual Networks Windows Azure IaaS and How It Works Deep Dive into Windows Azure Virtual Machines: From the Cloud Vendor and Enterprise Perspective An Overview of Managing Applications, Services, and Virtual Machines in Windows Azure Monitoring and Managing Your Windows Azure Applications and Services Overview of Windows Azure Networking Features Hybrid Will Rule: Options to Connect, Extend and Integrate Applications in Your Data Center and Windows Azure Business Continuity in the Windows Azure Cloud Linux on Windows Azure Blogs Understanding Windows Azure Virtual Machines An Overview of Windows Azure Virtual Network Virtual Machines and Windows Running SQL Server in a Windows Azure Virtual Machine Support for Linux Virtual Machines on Windows Azure

  Read the article

• Cyrus IMAP: Unable to connect to remote host: Connection refused

  - by Nick

  I'm working on setting up a Cyrus 2.2 IMAP server on Ubuntu Server 9.04. If I telnet from the server itself: # telnet localhost imap I get: * OK IMAP Cyrus IMAP4 v2.2.13-Debian-2.2.13-14ubuntu3 server ready Which is what I should be seeing. If I try from another machine on the network: telnet 192.168.5.122 imap I get: telnet: Unable to connect to remote host: Connection refused To the best of my knowledge, there is no firewall running on the box. I've tried restarting the saslauthd and cyrus2.2 daemons, with no effect. What else can I try?

  Read the article

• SSRS Subscription Fails

  - by Chad

  Our SSRS server is not executing a subscription correctly. (Only subscription we have btw) We created a subscription to export a report as an excel file to the file system. Tried running the job that gets generated, and this error happens 'EXECUTE AS LOGIN' failed for the requested login 'NT AUTHORITY\NETWORK SERVICE'. The step failed. It's not the most helpful in tracking down what exactly it was trying to do. EDIT Digging further into the logs I also get these errors w3wp!extensionfactory!f!7/30/2010-14:29:26:: w WARN: The extension Report Server FileShare does not have a LocalizedNameAttribute. w3wp!extensionfactory!11!7/30/2010-14:34:48:: w WARN: The extension Report Server Email does not have a LocalizedNameAttribute.

  Read the article

• Ping only works after about 30 seconds

  - by Ricardo Polo

  Today I am working on this issue and I would love your ideas. There is a network with something like this LAN 1 -- WAN CHANNEL--- LAN 2 The LAN 1 have two segments. When I make a ping from LAN 1 segment 1 it works like a charm. When I make a ping from LAN 1 segment 2 I have no ping, but after about 30 seconds of continues ping (ping -t) it start to work perfect. After some time of no activity with the destination host the issue happens again. Tracing the route packets stops in the last router before the target. This is the first router in LAN 2 after the WAN channel. In the next screenshot you can see thie issue, the first ping is before a continuos ping and the second one is while continous ping is running. Thank you in advance

  Read the article

• Distributing Files using a Group Policy on Windows Server 2003

  - by tonedeath

  A piece of software that we use at our office has recently moved to a new licensing system. This means that from now on a new set of license key files will need to be distributed to each of our 25 client installations every year. All of the clients run XP and are part of an AD domain controlled by a Windows 2003 DC. I'm already using group policies to deploy software updates. I gather that this is possible with Group Policy Preferences in Server 2008. I'm just looking for a good method using Server 2003. The same set of files need copying to each client. I also have them hosted on a network share accessible by each client. I'm more of a *nix person, so I'm not particularly up on scripting in a Windows environment.

  Read the article

• Cannot Access Web Interface on HP 2510G

  - by Stephen

  I am currently setting up a new infrastructure with HP 2510s as edge switches and an HP E5406 as the main switch. I also have a DHCP and DNS server running on the same network. When i first set up one of my 2510 switches, I gave it a static IP through the console and then went to the web interface to continue my configuration. Later, I realized that I assigned it the wrong IP address, so i went through the web interface and changed the IP address to the correct one. Now, I can't access the web interface. I can telnet to the switch on the new IP address, but the web interface will not load. If I switch from static IP to DHCP, it loads the web interface. Any ideas on what could be causing the web server in the 2510 not to load with the new static IP address?

  Read the article

• Gist (or other git-backed pastebin) on my own Server?

  - by Jim Dennis

  Does anyone know of a package to allow me to run a clone of gist on my own internal servers? I'd like to encourage our dev. teams to use a GIST like pastebin (with syntax highlighting and, preferably, with a git-based or git compatible backend). However, I want the code to remain within our network. Suggestions? (By the way, I've glanced at things like pygist but that's a client rather than providing the pastebin server side functionality. I suppose one option would be to add support for a Git backend to: pasttle

  Read the article

• Should I install an AV product on my domain controller?

  - by mhud

  Should I run a server-specific antivirus, regular antivirus, or no antivirus at all on my servers, particularly my Domain Controllers? Here's some background about why I'm asking this question: I've never questioned that antivirus software should be running on all windows machines, period. Lately I've had some obscure Active Directory related issues that I have tracked down to antivirus software running on our domain controllers. The specific issue was that Symantec Endpoint Protection was running on all domain controllers. Occasionally, our Exchange server triggered a false-positive in Symantec's "Network Threat Protection" on each DC in sequence. After exhausting access to all DCs, Exchange began refusing requests, presumably because it could not communicate with any Global Catalog servers or perform any authentication. Outages would last about ten minutes at a time, and would occur once every few days. It took a long time to isolate the problem because it was not easily reproducible and generally investigation was done after the issue resolved itself.

  Read the article

• Route packets from one VPN to another

  - by Mike

  I have two OpenVPN servers (10.8.0.0 and 10.9.0.0) set up on my OpenSUSE server. Within one network, each computer is visible to any other one, but I'd like to make it so that computers are visible across networks. I'd like to route the packets like this: when a user (say 10.8.0.6) pings an address on the other VPN (10.9.0.6), the packets are routed to the 10.9.0.1 and then to the appropriate computer in this VPN. How do I achieve this using iptables or a different tool? I tried the commands at the end of this section with no avail.

  Read the article

• Print server not being recognized after switching router and upgrading to 64 bit

  - by picardo

  I recently upgraded Windows 7 from 32 bit to 64 bit. I also switched my router from a very old model of Netgear to TP-Link. Before these updates, I had been using a USB print server by IOGear. After the updates, I took care to reinstall the drivers for both the print server and the printer, and picked the option to install a printer via TCP/IP, but no matter what I did, the driver software couldn't locate the print server on my network. I hit refresh, restarted my machine, turned off the firewalls and tried again. Still nothing. I'm at my wit's end. What else is left to try? Edit: More info. The print server is connected to the router via LAN line. The computer is connected to the router with a wireless connection.

  Read the article

• Assigning static IP and domain name mapping to local server in LAN

  - by yashbinani

  I have developed a web application which will be deployed in a LAN environemnt. Clients will be Computers/Android Tablets/IPAD In order for communication between client and local server 1) need to assign a static IP to local server. 2) need a domian name mapping for that IP address in Local environment. 3) router should assign the same static IP if it gets restarted etc. I am using a windows XP machine as Local server OS. Do i need to take care of router configurations before buying one, or all routers will have same capability to perform this task. I am not a network specialist, so Sorry if this question sounds stupid. Thanks

  Read the article

• Windows Server Backup 2012 error - "The version does not support this version of the file format."

  - by Cylindric

  I'm trying out Windows Server 2012, specifically Windows Server Backup, as it would be a very useful way to see us through until we can upgrade our 'real' backup system. I'm backing up to a network share, and a Server 2008 WSB works fine. On the 2012 server however, I get an error: Backup of volume \?\Volume{298d1a7d-f80f-11e1-93e8-806e6f6e6963}\ has failed. The version does not support this version of the file format. It's a VHDX written by WSB, so I'm not sure what version it's complaining about. I can see a whole bunch of files in the destination, so I don't think it's a simple authentication issue, but I only get about 8Mb of VHDX written.

  Read the article

• issue when promoting a second server as domain on r2 2008

  - by Mouradb

  Hello, I'm in an odd situatuion here, I've upgraded my network to a 2008 domain from a 2003 with out any issue, this works fine and all the FSMO are in one DC, I was about to install a second domain on a 2008R2 and this error is coming up again and again. I The problem is I keep getting an area telling me that I need to run adprep /domainPrep /forestPrep, but when I run it on the First DC, it tells me this has already been run and updated and it is aborted. Does anyone have any ideas on why I can't add a Server 2008 machine as a domain controller?

  Read the article

• Trouble with setting up Mac SSH with TP-LINK router

  - by arxanas

  I have a Mac running OS X 10.7.2, and a TP-Link TL-WR740N (whose control panel looks like this). Remote Login is on in the Mac's System Preferences, and port 22 is set to forward on the router. I can access my Mac as a web server using the external IP on port 80, which I have set up through the same port-forwarding mechanism provided by the router, but when I try to ssh server@external-ip, it just times out after a long while. (The same thing happens when I try vnc.) I can, however, ssh and vnc successfully into that computer while I'm on the same network when using its internal IP. Since ssh appears to work and port forwarding appears to work, I can't figure out what's causing the problem. Does anyone have any idea what might cause this?

  Read the article

• Win a Free License for Windows 7 Ultimate or Silverlight Spy at Our West Palm Beach .Net User Group

  - by Sam Abraham

  Shervin Shakibi, Microsoft Regional Director, ASP.Net MVP and Microsoft Certified Trainer will be our speaker at our West Palm Beach .Net User Group May meeting,  Shervin founded the FlaDotNet Users Group Network to which our West Palm Beach .Net User Group belongs. Shervin will be talking to us about the new features of Silverlight 4.0. I am personally looking forward to attending this event as I have always found Shervin's talks fun and a great learning experience.   At the end of our meeting, we will be having a free raffle. We will be giving away 1 free Windows 7 Ultimate license and 2 free Silverlight Spy licenses as well as several books and other giveaways. Usually, everybody goes home with a freebie.  We will also continue having ample networking time while enjoying free pizza/soda sponsored by Sherlock Technology and SISCO Corporation who is a new sponsor of our group.   Koen Zwikstra, Silverlight MVP and Founder of First Floor Software has kindly offered the West Palm Beach .Net User Group several free licenses of Silverlight Spy to raffle during our meetings. We will start by raffling two copies during our May meeting.   Silverlight Spy is a very valuable tool in debugging Silverlight applications. It has been mentioned at MIX10 ( http://firstfloorsoftware.com/blog/silverlight-spy-at-mix10/) as well as by Microsoft Community Leaders (http://blogs.msdn.com/chkoenig/archive/2008/08/29/silverlight-spy.aspx)   I am using Silverlight Spy myself and will probably be using it to demonstrate Silverlight internals during my talks. I think Koen's gift to our group will bring great value to our fortunate members who end up winning the licenses. Thank you Koen for your kind gift and looking forward to meeting you all on May 25th 2010 6:30 PM at CompTec (http://www.fladotnet.com/Reg.aspx?EventID=462)   Sam Abraham Site Director - West Palm Beach .Net User Group

  Read the article

• Connecting to Aerohive APs from Laptops running Win. 7 using authentication from a Windows 2008 domain server

  - by user264116

  I have deployed a wireless network using Aerohive access points. 2 of them are set up as radius servers. I want my users to be able to use the same user name and password they use when they log onto our domain. They are able to do this from android devices or computers running Windows 8. It will not work on Windows 7 machines. How do I remedy this situation, keeping in mind that the machines are personal machines not company owned and I will have no way to change their hardware or software.

  Read the article

• Permissions problem on mounting afp drive

  - by Ron Gejman

  I am trying to mount a network drive via AFP on an Ubuntu 10.04 server machine. After installing AFP support, I use the following command: sudo mount_afp afp://USER:[email protected]/directory/ /media/dir This seems to work and it tells me that mounting succeeded. However, when I navigate to /media/dir I get the following error: cd: cfs: Input/output error Permissions in /media are: d????????? ? ? ? ? dir/ drwx------ 12 user 4.0K 2010-10-25 16:08 otherdisk/ So there is a permissions problem here. I eventually want to mount this drive automatically using fstab. What do I need to do to make the disk accessible?

  Read the article

• MX Record Propagation

  - by Ryan

  How long does it take a change in MX records to propagate? Is the MX record TTL the max time it will take or do we also need to wait for all DNS records to propagate? We are changing our mail server from Exchange 2003 to Exchange Online. Our current MX records (at Network Solutions) have a 1 & 2 hour TTL (primary and backup MX respectively). When we change the MX records to point to Exchange Online should all MX records worldwide be updated within 2-4 hours or should we assume the traditional 48 hours for DNS to propagate? I assume that once all MX records propagate that all new incoming email will be directed to the new server.

  Read the article

• Start synergy on boot of Ubuntu 12.04

  - by SwimBikeRun

  I am having problems getting synergy to start on boot of my Ubuntu 12.04 desktop machine. I followed the troubleshooting at Start synergy on boot? completely, but I still couldn't get synergy to start on boot up. I tried running my client starter script manually and here is what resulted: m@m-o:/etc/synergy$ cat startsynergyc #!/bin/bash /usr/bin/synergyc -n MWin1 3.22.21.145 m@m-o:/etc/synergy$ ll total 28 drwxr-xr-x 2 root root 4096 Oct 30 14:29 ./ drwxr-xr-x 143 root root 12288 Oct 30 14:31 ../ -rwxr-xr-x 1 root root 54 Oct 30 14:29 startsynergyc* -rwxr-xr-x 1 root root 67 Oct 30 14:06 startsynergys* -rw-r--r-- 1 root root 659 Oct 30 14:06 synergy.conf m@m-o:/etc/synergy$ ./startsynergyc INFO: Synergy 1.4.14 Client on Linux 3.8.0-32-generic #47~precise1-Ubuntu SMP Wed Oct 2 16:19:35 UTC 2013 x86_64 It appears that synergy is running. This is exactly what is being told to startup with ubuntu assuming I did the lightdm modification correctly. However, I don't see any synergy running, and I certainly can't control the other computer. Btw, I changed my ip in the log from what it actually is ~ Is this a necessary precaution or are ips local to the network? What does knowing my IP allow someone to do?

  Read the article

< Previous Page | 511 512 513 514 515 516 517 518 519 520 521 522  | Next Page >