Search Results

Search found 18766 results on 751 pages for 'me again'.

Page 519/751 | < Previous Page | 515 516 517 518 519 520 521 522 523 524 525 526  | Next Page >

• Connecting a laptop to a TV via HDMI

  - by Madmartigan

  I just bought a new Dell XPS17 laptop (Win7) that only has HDMI output. My last 2 laptops had VGA, which I used to connect to my Sony Bravia 32" TV with no issues, but with the HDMI it's been quite a headache. Drivers for display adapters have been updated to the latest versions: Intel(R) HD Graphics Family NVIDIA GeForce GT 550M I went to a store and plugged in to 4 different TVs from different manufacturers. A sales rep and I spent about 30 minutes being baffled by the results (which are the same as my current TV): Extreme buggy behavior in the Nvidia and Windows display/resolution control panel Can not extend or duplicate displays, can only select one Third and fourth output devices "randomly" detected by the Windows control panel Could not get the screen to fit the output (edges cut off on all sides by about a half inch) Resolution and colors less than perfect. Artifacts around text. Display "randomly" cuts out Defaults to TV output only when plugged in Can not change resolution on either device when connected No audio from the TV Plugged in to 3 monitors from different manufacturers: Defaults to duplicated displays when plugged in Everything works perfectly So far, four people have gone through all the settings in the latop with no luck. I had similar, but not exactly matching results with a different laptop. I'm using the Sony Bravia currently at home, but in order to get it to work I have to turn on the laptop, wait until the display shows up on it, close the lid, then cycle through each output channel on the TV until I come back around to the HDMI port again, but still I have the symptoms described above. However: Once in a while, it just works. Sometimes, seemingly randomly, the output fits the screen perfectly. Sometimes the audio comes through the speakers too, but not always. Usually my screen saver "Mystify" will come up with a message that it cannot be displayed due to a limitation of the video card, but then sometimes it works fine. These 3 things seem to be independent of each other and don't always happen together. So, is there any way to get the laptop to output correctly to a TV, or is it just not meant to be?

  Read the article

• Windows File Access Denied

  - by Tom

  I seem to have a general problem with "access denied on Windows". It manifests itself every time if e.g: My bat file calls a compiler creates a file on disk My bat file renames a file But I also have files downloaded (FireFox) to Windows desktop where Windows is giving me "access denied" if I try delete the file. Tried disable AVG + make exception in AVG resident shield (I have tried checking with Task Manager + Winternals process explorer that it is not process running still running that should cause the locks.) Windows 7. My user account is an administrator. All files are created by same user account. The problem is recent, but some things I first noticed yesterday (when I started calling .bat files again which I have used for many years) I have tried: Starting e.g. Windows Explorer with "run as administrator", but that makes no difference right-click - properties - security and changes permissions/ownership (I also get "access denied" when trying this so this does not help) Here is a ascreenshot if I try change security of a "locked" file. (The problem here is the locking occurs continously every time the file is created) ! If I click on, it states I am not the owner? Which baffles me as I just created it. (Yes, through a .bat file calling executables that create the file. But all running under my administrator user account. Interestingly after having this dialog open, the file somehow sometimes suddenly seem to allow me delete it)

  Read the article

• How to reinstall bootloader after migration to SSD

  - by hijarian

  I must say, it was difficult to name this question. Basically, I need to properly reinstall the bootloader on my system, because I already have the working system disks for my OSes. The long story is this: I had the large slow HDD with Windows7 & Debian Wheezy dual-boot on it, perfectly bootable. Then, I ordered the SSD drive and prepared my system partitions to fit onto the much smaller SSD. I wanted the following schema: 128 GB Windows 24 GB / on Debian 86 GB /home on Debian Strange size for /home because there's no such thing as true 256GB disk drive. So, I've prepared such a partitions on my initial HDD and installed the new SSD and then I loaded the GParted live USB (can't remember now how it was really named), and then just copypasted the partitions from HDD to SSD. So, now I have the following partitions across the physical disks: SSD 128 GB copy of original Windows partition 24 GB copy of presumably Debian / 86 GB copy of presumably Debian /home HDD 128 GB Windows 24 GB / on Debian 86 GB /home on Debian ... several other partitions with non-system data ... And the behavior of the system right after the Ctrl+C, Ctrl+V in GParted was as follows: no GRUB, system boots right into the Windows on HDD. In BIOS settings are to boot from SSD first. I managed to create the Debian Testing installation USB and loaded it into the rescue mode, found that it identified my SSD as /dev/sda and installed the GRUB to the /dev/sda. Now my system loads the GRUB which lists both Windows and Debian. From HDD. So, I am now back into initial position. Please, how I should set up the GRUB so it'll load the OSes correctly from SSD? Should I fire up my Debian, fiddle with the GRUB's config and reinstall it again to the same place (at SSD)?

  Read the article

• Failed to re-publish a page - Tridion 2011 SP1

  - by Wilson Yu

  We are getting some strange error when re-publishing the same page. The page was published successfully the first time and we can see the page from presentation server. It failed with the following error (see below) when we tried to publish it again (no change to page). The page ran OK within template builder and we got the correct html output, it failed in the last committing deployment step (Prepare Transport, Transporting, Preparing Deployment and Deploying are all successful). Once it fails to publish the second time, it always fails to publish, and we can't un-publish it either. Also when we make a copy of the failed page and create a new page, we can publish the new page first time, the new page then fails to publush the second time with the same error. Does anyone know what would cause this error? any help would be greatly appreciated. Here is the error msg: Committing Deployment Failed Phase: Deployment Prepare Commit Phase failed, Unable to prepare transaction: tcm:0-4210-66560, For input string: "", For input string: "", Unable to prepare transaction: tcm:0-4210-66560, For input string: "", For input string: ""

  Read the article

• How do I upgrade Windows Server 2008 R2 Standard (OEM Key) to Enterprise (MSDN Key) using DISM?

  - by Tom Crane

  (Originally asked as After upgrading to 2008 R2 Enterprise and installing more RAM, Windows can only see 4.00 GB but now I know what the question really is...) My Dell server came preinstalled with 2008 R2 Standard. I upgraded to Enterprise to take advantage of more than 32GB RAM. This server is purely for dev and testing, so I want to use my MSDN product key for the upgrade. I originally tried to uprade using the MSDN Enterprise key, but it wouldn't have it: dism /online /Set-Edition:ServerEnterprise /ProductKey:[MSDN key] => Error DISM DISM Transmog Provider: PID=5728 Product key is keyed to [], but user requested transmog to [ServerEnterprise] - CTransmogManager::ValidateTransmogrify I tried several things, including changing the current product key to the MSDN one. Eventually I used a KMS generic key which can be found in several technet forum posts. dism /online /Set-Edition:ServerEnterprise /ProductKey:[KMS Generic Key] ... and this appeared to work. I then changed the product key again (using the control panel) to the MSDN key, thinking that was the end of the matter. Only later when tried to start up VMs did I realise I only had 4GB of usable RAM. I didn't make the connection with the licensing changes at this point and went off on a wild goose chase of BIOS settings, memory configurations and the like. Only later when I saw this... http://social.technet.microsoft.com/Forums/en/winserverTS/thread/6debc586-0977-4731-b418-ca1edb34fe8b ...did I make the connection and reapply the KMS Generic key - which gave me all the RAM back. But now I have a system that isn't properly licensed, presumably I won't be able to activate it as it is, so I've got 2 days to enjoy it. With the MSDN key applied, only 4GB RAM is usable. Is there a way round this without a) rebuilding the server from scratch with the MSDN key from the start or b) buying a retail Enterprise license

  Read the article

• SQuirreL Client: Opening up a table in a separate tab

  - by Dalin Seivewright

  I've switched to SQuirrel Client to view an Oracle database with a variety of tables. At any given time, I need to look at the contents of several related tables at the same time. The problem is that, at least by default, SQuirrel Client does not open up multiple tables at a time. When you click on a different Table object, the main view is refreshed with newly selected table data. Oracle's SQLDeveloper (which I am trying to move away from) did this by default if I recall, but there was an option to "freeze" panes. Does a similar option exist in SQuirrel Client? I do not require the ability to view the contents of two different tables on the same screen (i.e. a split view) but I would like the ability to have tabs for each table so I can quickly switch between each table view rather then having to find the table in the table list over and over again. Note: I am using this in a professional capacity but if it does not "belong" here then I suppose it could be moved to superuser.

  Read the article

• Computer Won't Boot Properly, unless in safe mode?

  - by Mr_CryptoPrime

  I bought a computer today and booted it up, but when I did I only got a blank screen. I checked to make sure it wasn't the monitor by connecting it to my old computer...it worked. I then tried connecting my monitor to both DVI ports and found that the bottom one did work. However, now it just boots up and says "loading windows" and then when the login screen is suppose to come up the screen just goes blank and monitor says "no input, check cord" (or something like that). I tried reinstalling windows and then I was able to log on normally. I used the CD's and reinstalled all the drivers, then rebooted...now I am stuck right back where I started. I tried taking out the RAM and inserting into different slots, that didn't fix anything. I was able to boot up into windows using safe-mode. I suspected that my ATI Radeon 6950 was the issue and downloaded the drivers, but I can't install them on safe-mode. Someone said to install C++ distr. and I tried doing that to fix driver installation problem of "failed to load detection driver" but it wouldn't let me do that either. Please someone help me, I don't want to have to deal with the evil redtape of sending it back to get a replacement! My computer: -Content--text-_-"http://www.newegg.com/Product/Product.aspx?Item=N82E16883229236&nm_mc=TEMC-RMA-Approvel&cm_mmc=TEMC-RMA-Approvel--Content--text-_- Driver detection problem: http://www.hardwareheaven.com/hardwareheaven-tools-discussion/174912-failed-load-detection-driver-installation-error.html Driver download page: http://sites.amd.com/us/game/downloads/Pages/radeon_win7-64.aspx#1 I am using windows 7. Thanks again.

  Read the article

• SVN hangs on commit - any suggestions for troubleshooting?

  - by Richard Beier

  We're having a problem with SVN... Subversion clients such as TortoiseSVN hang when we commit any more than a few files at a time to our server. Everything appears to actually be committed successfully to the repository; but the client hangs after all the data has been transmitted. We're using version 1.4.4 of the SVN server. We use the svn:// protocol rather than http to connect. We've reproduced this problem with several clients: TortoiseSVN (1.6.10), AnkhSVN (2.1), and the Silk command-line client (1.6.12). This is happening for everyone on the team, though some people seem to be more affected than others. If someone commits only a few files, it often works; but with more than half a dozen files, it usually hangs. Does anyone have troubleshooting suggestions? This has been happening sporadically for a while, but it's become pretty consistent lately. We've been working around the issue by killing the hung SVN client, doing "svn cleanup", and then doing "svn up"; but sometimes that causes tree conflicts. Another workaround is to blow away the workspace and check it out again after every commit; but of course that's pretty annoying. Are there any diagnostics that could help us troubleshoot this? We're considering upgrading to SVN 1.6 server, and installing the server on a new machine; but we're wondering if there's an easier solution. Thanks for your help, Richard

  Read the article

• Why is writing to my external hard drive slow, while benchmarks show fast writing?

  - by matix2267

  I have an iOmega eGo 320GB portable drive connected through USB2.0 to my laptop running Windows Vista. It's been working fine for quite some time until recently it became very slow when writing e.g. when copying ~300MB movie over to the drive at first it is extremely fast but it actually doesn't write it only puts in cache and then hangs on last 10-20MBs for about a minute. When copying larger files it's the same story: starts fast but then slows down to ~5MB/s (sometimes even slower down to 2MB/s). Strange thing is that I have always had caching disabled for this drive (it was disabled by default and I never bothered changing it). At first I thought that the disk is dying so I checked S.M.A.R.T. values and everything is fine there. I also run chkdsk and it seemed to fix the problem - it worked fast for a few minutes but then it slowed down again. I also tried plugging it into another USB port - no difference. Additionally I noticed that reading under certain circumstances is sometimes slower e.g. loading times for some games are ~10 times longer, whereas simple copying files from this drive to my internal HDD is fast. I ran a speed benchmark using CrystalDiskMark with a 5x100MB run and strangely got these results: read write (MB/s) Seq 33.05 28.25 512k 17.30 15.27 4k 0.267 0.372 4kQD32 0.510 0.260 This is different from what most other people have (I've found many threads about slow disk write while googling but all of them were slow on benchmarks too) which is why I decided to post this problem here. BTW most of the time when writing (or sometimes reading) the activity led is mostly idle (blinks a while and then stops for longer, sometimes has slower blinks ~1 sek, sometimes goes off for a few seconds - extremely long blink :) ) but when benchmarking, defragmenting or just reading (copying from this drive, installing apps from installers there, watching HD videos) it is blinking really fast (like it should) and there are no slowdowns. It shouldn't be driver issue unless stock Windows drivers have some issues I'm not aware of.

  Read the article

• PowerConnect 3548p SNTP and web interface not working

  - by Force Flow

  I have been unable to get SNTP and access to the web interface working properly on a Dell PowerConnect 3548p. In the logs, this message appears over and over again: 04-Jan-2000 20:19:29 :%MNGINF-W-ACL: Management ACL drop packet received on interface Vlan 172 from 172.17.0.3 to 172.18.0.10 protocol 17 service Snmp 172 is the management vlan. 172.17.0.3 is the DNS server 172.18.0.10 is the switch's IP address. The DNS server and the switch are located on different subnets and separated by routers. I am unable to access the web interface of the switch from the 172.17.x.x subnet. I can only access the web interface of the switch if I am accessing it from the 172.18.x.x subnet. There is also a managed linksys switch on the 172.18.x.x subnet on the 172 vlan, which has no problem with SNTP. I can also access it from the 172.17.x.x network. So, it stands to reason that this is not a firewall or routing issue, but with the 3548p switch. I suspect the issue is with management permissions/ACLs on the 3348p switch, but that's about as much as I've been able to determine so far. Any ideas?

  Read the article

• Java: very slow tomcat and too big war file

  - by NaN

  I created some sort of RESTful API backend for a mobile app. It's written completely in Java using Jersey as Framework. At the moment no database is used, it's all in the memory, but this is no problem so far (it's only for prototyping purposes). I ordered the smallest package from digital ocean and installed tomcat7. All in all tomcat works, but I have three major problems: 1) It takes a long time until tomcat deploys the app: I deploy it per tomcat manager and it takes about 2 minutes unit the site works (excl. war upload time). 2) The war files are quite big (16MB): I don't know why they are so big. There are no database dependencies and most logic is written in plain java. Okay, we are using jersey, but 16MB are a lot for the logic of a small webservice. 3) I have to restart tomcat all 3 days or so. It looks like a memory leak or something similar. If the app runs for a few days the response time is quite high and the server seems to be frozen. It works again, if I restart tomcat per ssh. You can find my mvn pom file right here. Do you have some tips? Are there good tomcat alternatives?

  Read the article

• Winamp playing sound but no video

  - by Greg Sansom

  I am having problems playing video in Winamp (the movie I am trying to play is an AVI - not sure if other formats work). I have installed the K-Lite Codec Pack, and the video does work in Winamp Classic. I can also play the video in Winamp on another machine (although I can't remember the exact configuration details of that machine - and I don't think they're relevant). There are a few symptoms: The content of the Video view is either empty, transparent, or displays rendering from other programs. Opening the Visualization view shows the following error: MILKDROP ERROR DirectX initialization failed (GetDeviceCaps). This means that no valid 3D-accelerated display adapter could be found on your computer. If you know this is not the case, it is possible that your graphics subsystem is unstable; please try rebooting your computer and then try to run the plugin again. Otherwise, please install a 3D-accelerated display adapter. Trying to open streams via the SHOUTCast TV plugin shows Error opening video output, and the video does not open. Opening the file with WMC causes the following error (although the movie still plays): Error creating DX9 allocation presenter CreateDevice failed D3DERR_NOTAVAILABLE There are no warnings displayed in Device Manager, although the display adapter is the standard Windows one. Running DxDiag shows no problems (codec for Video listed as XviD 1.1.2 Final). GSpot reports that codecs are installed. System specs: - Windows Server 2008 r2 Standard 64-bit, with latest updates; - .NET 3.5.1 installed; - Winamp v5.6.01 (latest version); - DirectX 11 (Latest version); - K-Lite Codec Pack 7.0.0 (Full); - Machine is HP DC7600 - full specs here. Please comment if there is any more information which will help to diagnose the problem.

  Read the article

• Does my Oracle DBA need root access?

  - by Dr I

  I'm currently discussing with my Oracle DBA Collegue that request a root access on our production servers. I'm not so hot to let him use the root access on our production servers. He is arguing that he need it to perform some operations like restarting the server and some other obscure arguments. The point is that I'm not agree with him because I've set him a Oracle user/group and a dba group where Oracle user belong. Everything is running smoothy and without any root permissions for now. I also think that all administrative tasks like scheduled server restart and so one need to be operated by the proper administrator (The Systems administrator on our case) to avoid any kind of issues related to a misunderstanding of the infrastructure interactions. So, I need the help of both, sysadmins and Oracle DBAs to lead me on the correct direction. If my collegue really need this rights I'll give him, but I'm just basically quite affraid of that because of security and integrity concerns. I know that my collegue is really good as a Oracle DBA and he know is work very well, but I also know that I've very few cases where a software and its admin really need root access. Once again, I'm not looking for pros/cons but rather an advice on the way that I should take to deal with this situation.

  Read the article

• How to include worksheet 3 and 4 in a cell formula provided?

  - by user21255

  I have been kindly given this formula with an explanation on how it works: Insert this formula into the cell B4 of the sheet "Cases": =IF(NOT(ISBLANK('1st'!B25)),'1st'!B25,IF(NOT(ISBLANK(INDIRECT("'2nd'!R" & (ROW($B4)-(COUNTA('1st'!$B:$B)-COUNTA('1st'!$B$1:$B$24))-4+25) & "C" & COLUMN(B4),FALSE))),INDIRECT("'2nd'!R" & (ROW($B4)-(COUNTA('1st'!$B:$B)-COUNTA('1st'!$B$1:$B$24))-4+25) & "C" & COLUMN(B4),FALSE),"")) Copy the formula to the other cells in the worksheet; the relative addresses will adjust automatically. The formula works like this: Check if there is content in 1st. If yes, copy it. If no, find out how many entries there are in 1st in total. (This is done by using the COUNTA function on the whole B column in 1st and subtracting the number of non-empty cells above the actual case data.) Use this information together with the current cells's number to find out the location of the cell that has to be copied from 2nd. Create the address of the cell and use the ISBLANK function on the INDIRECT function with that address to check if the cell is empty. If it is not, use the INDIRECT function again to display it. If it is empty, just display an empty string. Now this works fine when I have only 2 sheets. But lets say I want to include a third and fourth sheet (name as 3rd and 4th respectively), then what and should I put the formula for this in the formula above? There are actually 31 sheets but if I know how to add 3rd and 4th sheet in the formula, then I can figure out how to do the rest. Thanks

  Read the article

• IPTables Rule for Google Apps SMTP

  - by XpresServers

  I am trying to add iptables rule to allow traffic on ports 465 & 587 to google apps smtp servers. But I got not luck. My WHMCS installation works fine with google apps when I turn off iptables but iptables turn on itself again and email stop working. Please add rules to allow traffic from port 465 and 587. Following are my IPTables rules grabbed from /etc/sysconfig/iptables # Generated by iptables-save v1.3.5 on Fri Oct 5 01:33:52 2012 *filter :INPUT ACCEPT [2191:434537] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [2390:987151] :acctboth - [0:0] -A INPUT -j acctboth -A OUTPUT -p tcp -m multiport --dports 25,465,587 -m owner --gid-owner mailman -j ACCEPT -A OUTPUT -p tcp -m multiport --dports 25,465,587 -m owner --gid-owner mail -j ACCEPT -A OUTPUT -d 127.0.0.1 -p tcp -m multiport --dports 25,465,587 -m owner --uid-owner cpanel -j ACCEPT -A OUTPUT -p tcp -m multiport --dports 25,465,587 -m owner --uid-owner root -j ACCEPT -A OUTPUT -j acctboth -A OUTPUT -o eth0 -p tcp -m tcp --sport 587 -m state --state ESTABLISHED -j ACCEPT -A OUTPUT -o eth0 -p tcp -m tcp --sport 465 -m state --state ESTABLISHED -j ACCEPT <<IN THIS SPACE RULES ARE RELATED TO SPECIFIC IPS ONLY>> -A acctboth -i ! lo COMMIT # Completed on Fri Oct 5 01:33:52 2012 # Generated by iptables-save v1.3.5 on Fri Oct 5 01:33:52 2012 *nat :PREROUTING ACCEPT [196:12398] :POSTROUTING ACCEPT [191:15070] :OUTPUT ACCEPT [190:15010] -A OUTPUT -p tcp -m multiport --dports 25,465,587 -m owner --gid-owner mailman -j RETURN -A OUTPUT -p tcp -m multiport --dports 25,465,587 -m owner --gid-owner mail -j RETURN -A OUTPUT -d 127.0.0.1 -p tcp -m multiport --dports 25,465,587 -m owner --uid-owner cpanel -j RETURN -A OUTPUT -p tcp -m multiport --dports 25,465,587 -m owner --uid-owner root -j RETURN -A OUTPUT -p tcp -m multiport --dports 25,465,587 -j REDIRECT COMMIT # Completed on Fri Oct 5 01:33:52 2012 Thanks Hassan

  Read the article

• Cannot Start Passenger 3.0.18 Using Mountain Lion (OS X Server) and RVM

  - by LightBe Corp

  I recently did a clean install of Mountain Lion on my Mac Mini Server. I installed version 3.0.18 using a gem according to the directions on http://www.phusionpassenger.com with no errors that I could see. rvmsudo gem install passenger-enterprise-server-3.0.18.gem rvmsudo passenger-install-apache2-module Here are my entries in /etc/apache2/httpd.conf with my username masked: LoadModule passenger_module /Users/username/.rvm/gems/ruby-1.9.3-p327/gems/passenger-enterprise-server-3.0.18/ext/apache2/mod_passenger.so PassengerRoot /Users/username/.rvm/gems/ruby-1.9.3-p327/gems/passenger-enterprise-server-3.0.18 PassengerRuby /Users/username/.rvm/wrappers/ruby-1.9.3-p327/ruby I uncommented out the following statement: Include /private/etc/apache2/extra/httpd-vhosts.conf Here is a sample virtual host entry. I have three of them in the file. <VirtualHost *:80> ServerName www.mydomain.com ServerAlias mydomain.com PassengerAppRoot /Users/username/Sites/myfolder/ DocumentRoot /Users/username/Sites/myfolder/public <Directory /Users/username/Sites/myfolder/public> Allow from all AllowOverride all Options -MultiViews </Directory> </VirtualHost> I have restarted Apache several times. Here is information from my server: [~]$ ps -ef | grep Passenger 501 18804 303 0 12:39PM ttys000 0:00.00 grep Passenger [~]$ rvmsudo passenger-status Password: **ERROR: Phusion Passenger doesn't seem to be running.** [~]$ rvmsudo passenger-config --version 3.0.18 I have tried doing online searches on this. I was surprised that there was not all that much on this specific error even though from my understanding Passenger has been around for a few years. I have posted this issue on the Phusion Passenger Google Groups but have not heard anything. Any help would be appreciated, the sooner the better LOL. Seriously I need to have one of my three websites up by tomorrow evening. This is the only issue stopping that from happening. Thanks again.

  Read the article

• Linux Startup Script after Gnome Login

  - by Eric

  I have a Fedora server that I want to spawn an interactive python script after the user logs on. This script will ask the user for various types of information for configuring the system or it will search for the previous config file and show them the predefined information. Originally I was going to put this in rc.local or make it run with init.d but that messed up the boot due to how the script is spawned. So I would like this script to run as soon as the user logs in to Gnome. I've searched around quite a bit and found this answer which appears to be exactly what I want, but it isn't working the way I want it to. Below is my entry. [Desktop Entry] Name=MyScript GenericName=Script for initial configuration Comment=I really want this to work Exec=/usr/local/bin/myscript.sh Terminal=true Type=Application X-GNOME-Autostart-enabled=true Whenever I login, nothing happens. So I then did a test to modified "myscript.sh" to just echo some text to a file and it worked fine. So it appears the portion that isn't working is the script popping open a terminal and waiting for the users input. Are there any additional options I need to add to make this work? I can confirm when I run /usr/local/bin/myscript.sh from the CLI it works fine. I have also tried adding "StartupNotify=true" and still no luck. Edit @John - I tried moving my Exec= to /usr/local/bin/myscript-test and this is what myscript-test contains. #!/bin/bash xterm -e /usr/local/bin/myscript.sh Yet again, when I just run the myscript-test it works fine. However when I put that in my autostart, nothing happens. Edit 2 - I did a few more tests and it did start working but I had to remove Terminal=True before the xterm would pop. Thanks for your help.

  Read the article

• How do I stop linux from trying to mount android phone as usb storage?

  - by user1160711

  When I plug in my Motorola Triumph to my fedora 17 linux box USB port, I get an endless series of errors on the linux box as it desperately attempts to mount the phone as a USB drive. Stuff like this: Jun 23 10:26:00 zooty kernel: [528926.714884] end_request: critical target error, dev sdg, sector 4 Jun 23 10:26:00 zooty kernel: [528926.715865] sd 16:0:0:1: [sdg] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jun 23 10:26:00 zooty kernel: [528926.715869] sd 16:0:0:1: [sdg] Sense Key : Illegal Request [current] Jun 23 10:26:00 zooty kernel: [528926.715872] sd 16:0:0:1: [sdg] Add. Sense: Invalid field in cdb Jun 23 10:26:00 zooty kernel: [528926.715876] sd 16:0:0:1: [sdg] CDB: Read(10): 28 20 00 00 00 00 00 00 04 00 If I go ahead and tell the phone to allow linux to mount the USB storage, the messages stop, and I get a mounted drive, but if all I want to do is use the debug bridge, my log on linux will continue to fill with this junk. Is there some udev magic I can do to make the system ignore this particular device as far as usb storage goes? I just noticed that if I tell the phone to enable USB storage, let linux recognize the new disk, then tell the phone to disable USB storage again, I get one additional log message about capacity changing to zero, but the endless spew of messages stops, so I guess one work around is to enable and disable USB right away.

  Read the article

• virtual machines, dual booting and data disks on SSD

  - by stevemarvell

  This is in planning, so if I've got the strategy wrong, please let me know. There are multiple questions here, but I think they all degenerate to the same answers. The hardware is a laptop with a single SSD. I'm trying to not lose the performance of the SSD. I plan a native dual booting Windows (plus cygwin) and Linux machine which is my BYOD and represents the development environment. I keep the codebase on a shared partition (though sometimes this is an external thunderbolt SSD) which can be natively "mounted" by whichever OS is in operation. I boot into one or the other environments depending on the task in hand. Sometime I have to develop with windows tools, but generally, Linux is my preferred development environment. It would be ideal if I could VM the other OS and run either in either. I'm going to assume, because I've not found a sensible VM based solution, that I have get samba involved to share the code partition between VMs. Is this going to blow my SSD performance in the VM? The client also supplies me with a VM for the target environment, usually linux. This is not often suited to development and is used for testing only. I normally keep two copies of this, one as a sandbox and one which I deploy to using the client's preferred method. I keep these VM snapshots on the shared partition. The latter is interacted with over the network and so has no disk sharing requirements. However, it would be useful for the sandbox to be able to "mount" the code base from the natively running OS. Is this samba or nfs again, depending on the native OS? Am I missing a trick which allows this to all work smoothly with all four environments running at once without loosing the SSD performance?

  Read the article

• How I can fix the "Display Driver has stopped responding and has recovered"?

  - by Vitor Rangel

  I'm using a GeForce GTX 580, with Windows 7 64-bit. The driver version of the GTX is 301.42. The problem happens after a few minutes, when I'm playing specifc games. It won't happen in all games - And I don't have any idea why these games doesn't work. The games that doesn't work: Battlefield 3, Civilization V, Sniper Elite V2. The games that work: Mass Effect 3, Crysis 2, Team Fortress 2, Left 4 Dead 2, Skyrim, L.A. Noire. As you can see, it's not a problem of "The games that demand more stop working". I've tryed updating the driver of the graphics-card, the bios of the motherboard, even formated my computer (It was needing it) and instaled every driver in the last version possible. This problem happens since I bought my graphics-card, 6 months ago. After a few minutes, from 10 to 20, the pixels in the monitor become strange, with random colors and effects, like it was broken. Then, everything goes black, and the message appears "Display Driver has stopped responding and has recovered". After that, I need to close the game and start again. I am not overclocking, and my temperature never goes higher than 70ºC.

  Read the article

• Removing extended partition without deleting logical in it

  - by HisDudeness

  I'm running a Linux-based laptop, and in order to multi-boot several distros in it, I created an extended partition which contains a bunch of logical ones with GParted. Now, after quite a long time with this setup, I've changed my mind because of the consequent lack of storing space for my data partition. Now I want to keep one distro alone like it's normal, and eventually have some other operating systems stored in external supports to plug in and use if I want. Obviously, also this partition I want to keep (and to enlarge a little too) is just a logical inside the extended I want to keep. For what concerns the number I'm ok, meaning I currently have this big distro dedicated extended, the swap and the data partitions, so there's space for another primary before I delete the extended, but I don't know how to delete it without touching the logical in it, I don't want to reinstall the system losing all changes and settings, and I don't want to keep an extended partition for a logical alone. How can I do? Do I have to create a new primary, copy the logical content in it and then delete everything? Will the system boot and maintain exactly all the features it has now? Or is there a way to convert an extended into a primary once it contains just one logical? Or can I directly move a logical out of an extended turning it into a primary? Or, again, am I screwed?

  Read the article

• Windows 7 caches FTP credentials?

  - by Martin Booka Weser

  On my remote maschine i have an iis 7.5 (win server 2008) and set up an ftp site with iis manager authentication. I then did active directory user isolation and isolated my users to physical folders according to their names. So far, so good. I can access with ftp cliens from everywhere with different test accounts that i previously set up in the iis manager auth. Every user connects to its own folder. When i now tested with windows 7 as a client i did the following. Explorer - computer - right click - add network address - the ip of my remote maschine - user1 - password1 Perfect - it works. I now want to connect with user2. So I deleted this network address and set up a new connection, but with user2 (or even anonymous) instead. Now the strange thing: Windows doesn't even ask me for a password again. It just connects me to the folder of the user1. I already disabled ftp caching in the IIS and i disabled the user1 account in IIS manager authentication! Still, if i set up a network connection with this windows 7 it connects to the folder user1 . No matter which username i use (anonymous, administrator, user2,...). And if i connect with other ftp clients or other computers it all works perfectly. So I assume that this one windows somehow caches the credentials... But then, why does the IIS still accepts this credentials even if i disabled this user1 account??? Thanks.

  Read the article

• Comparing 2 (or 3 Files If Possible) "Line By Line"

  - by PythEch

  I want to find out the differences of 2 (or 3 files if possible) line by line. Diff utils can do this, however it gives inaccurate results. Because, 2 files have exact number of lines which is "134". But diff gives me "Added Lines" and "Removed Lines". However this is wrong, they have exact the same number of lines, there is no added or removed lines. The text files which I want to find differences of them, have only numbers written, maybe that's why that algortihm fails. I couldn't find any option to prevent that, however I may be wrong, I mean there should be an option for that, but again, I couldn't find. This is what I get (5am.txt vs 6am.txt, there is a huge problem): This is what I want (6am.txt vs 7am.txt, still has problems): But, first the first image still has this problem, at the last lines. Edit: After I figured out that there is no utility to do this, I handled myself. I almost did the same thing as what RedGrittyBrick have done. This script imitates diff utility so I (or you) can use it with diff2html. To use it with diff2html, just change line diff_stdout = os.popen("diff %s" % string.join(argv[1:]), "r") to diff_stdout = os.popen("script.py %s" % string.join(argv[1:]), "r") and name this script whatever you want: import sys f1=open(sys.argv[1],"r") f1_read=f1.readlines() f1.close() f2=open(sys.argv[2],"r") f2_read=f2.readlines() f2.close() changed={} first_c = "" for n in range(len(f1_read)): if f1_read[n]!=f2_read[n]: if first_c == "": first_c=n+1 changed[first_c]=n+1 else: first_c="" #Let's imitate diff-utils... for (x, y) in changed.items(): print "%d,%dc%d,%d" % (x,y,x,y) for i in range(x,y+1): sys.stdout.write("< %s" % f1_read[i-1]) print "---" for i in range(x,y+1): sys.stdout.write("> %s" % f2_read[i-1]) Final results:

  Read the article

• Unable to connect via NetBIOS Name

  - by grom

  I can't connect to machines/shares by NetBIOS names. Below is console output showing the problem. C:\>nbtstat -n Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] NetBIOS Local Name Table Name Type Status --------------------------------------------- BEAST <00> UNIQUE Registered WORKGROUP <00> GROUP Registered BEAST <20> UNIQUE Registered WORKGROUP <1E> GROUP Registered WORKGROUP <1D> UNIQUE Registered ..__MSBROWSE__.<01> GROUP Registered C:\>nbtstat -A 192.168.1.3 Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] NetBIOS Remote Machine Name Table Name Type Status --------------------------------------------- BRCLAPTOP <00> UNIQUE Registered WORKGROUP <00> GROUP Registered BRCLAPTOP <20> UNIQUE Registered WORKGROUP <1E> GROUP Registered MAC Address = 00-1C-BF-14-B8-6E C:\>ping beast Pinging beast [fe80::59b8:179f:b90b:a63f%11] with 32 bytes of data: Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Ping statistics for fe80::59b8:179f:b90b:a63f%11: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\>ping brclaptop Ping request could not find host brclaptop. Please check the name and try again. C:\>nbtstat -a brclaptop Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] Host not found.

  Read the article

• Windows VirtualBox failed to attach USB device to Linux Guest

  - by joltmode

  I have Windows 7 64bit Host system, and I am using VirtualBox 4.1.18 (r78361). I have an Arch Linux Guest OS. I have installed VirtualBox Extension Pack (to enable USB2 support) and added my USB device filter to VM. I have also installed the Guest Additions provided by Arch: virtualbox-archlinux-additions (but I have no idea whether it's actually needed for my environment). I can see my USB device from VirtualBox Devices menu. Whenever I am trying to access it, I end up with: Failed to attach the USB device Kingston DT 100 G2 [0100] to the virtual machine Archlinux. USB device 'Kingston DT 100 G2' with UUID {a836ec33-0f41-4ca7-a31d-09cceaf5d173} is busy with a previous request. Please try again later. Details ? Result Code:    E_INVALIDARG (0x80070057) Component:      HostUSBDevice Interface:      IHostUSBDevice {173b4b44-d268-4334-a00d-b6521c9a740a} Callee:         IConsole {1968b7d3-e3bf-4ceb-99e0-cb7c913317bb} From what I have googled, most guides shows how to solve this the other way around - Linux Host to Windows Guest. How do I resolve this? Update I have tried to Eject (virtually, not physically) the device from my Windows Host system and then try to access the Device from Guest. Same error.

  Read the article

< Previous Page | 515 516 517 518 519 520 521 522 523 524 525 526  | Next Page >