Search Results

Search found 59084 results on 2364 pages for 'local system'.

Page 520/2364 | < Previous Page | 516 517 518 519 520 521 522 523 524 525 526 527  | Next Page >

• Ipsec config problem // openswan

  - by user90696

  I try to configure Ipsec on server with openswan as client. But receive error - possible, it's auth error. What I wrote wrong in config ? Thank you for answers. #1: STATE_MAIN_I2: sent MI2, expecting MR2 003 "f-net" #1: received Vendor ID payload [Cisco-Unity] 003 "f-net" #1: received Vendor ID payload [Dead Peer Detection] 003 "f-net" #1: ignoring unknown Vendor ID payload [ca917959574c7d5aed4222a9df367018] 003 "f-net" #1: received Vendor ID payload [XAUTH] 108 "f-net" #1: STATE_MAIN_I3: sent MI3, expecting MR3 003 "f-net" #1: discarding duplicate packet; already STATE_MAIN_I3 010 "f-net" #1: STATE_MAIN_I3: retransmission; will wait 20s for response 003 "f-net" #1: discarding duplicate packet; already STATE_MAIN_I3 003 "f-net" #1: discarding duplicate packet; already STATE_MAIN_I3 003 "f-net" #1: discarding duplicate packet; already STATE_MAIN_I3 010 "f-net" #1: STATE_MAIN_I3: retransmission; will wait 40s for response 031 "f-net" #1: max number of retransmissions (2) reached STATE_MAIN_I3. Possible authentication failure: no acceptable response to our first encrypted message 000 "f-net" #1: starting keying attempt 2 of at most 3, but releasing whack other side - Cisco ASA. parameters for my connection on our Linux server : VPN Gateway 8.*.*.* (Cisco ) Phase 1 Exchange Type Main Mode Identification Type IP Address Local ID 4.*.*.* (our Linux server IP) Remote ID 8.*.*.* (VPN server IP) Authentication PSK Pre Shared Key Diffie-Hellman Key Group DH 5 (1536 bit) or DH 2 (1024 bit) Encryption Algorithm AES 256 HMAC Function SHA-1 Lifetime 86.400 seconds / no volume limit Phase 2 Security Protocol ESP Connection Mode Tunnel Encryption Algorithm AES 256 HMAC Function SHA-1 Lifetime 3600 seconds / 4.608.000 kilobytes DPD / IKE Keepalive 15 seconds PFS off Remote Network 192.168.100.0/24 Local Network 1 10.0.0.0/16 ............... Local Network 5 current openswan config : # config setup klipsdebug=all plutodebug="control parsing" protostack=netkey nat_traversal=no virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off nhelpers=0 conn f-net type=tunnel keyexchange=ike authby=secret auth=esp esp=aes256-sha1 keyingtries=3 pfs=no aggrmode=no keylife=3600s ike=aes256-sha1-modp1024 # left=4.*.*.* leftsubnet=10.0.0.0/16 leftid=4.*.*.* leftnexthop=%defaultroute right=8.*.*.* rightsubnet=192.168.100.0/24 rightid=8.*.*.* rightnexthop=%defaultroute auto=add

  Read the article

• Powerpoint 2010 crash on quickstyle menu

  - by Marcus Lindblom

  Windows 7 64-bit, recent install, added Office 2010. When I create some boxes and open the quick-style menu, it crashes (or stops responding, in windowese, and then it sends an error report). I've run the "Repair" from the installer, but it didn't help. There's nothing in Windows Update I've Googled and searched on Microsoft's site, but n Any other ideas? (It's not related to this ppt crash question as that concerns PPT 2007. Error in event log: Faulting application name: POWERPNT.EXE, version: 14.0.4754.1000, time stamp: 0x4b967cf2 Faulting module name: KERNELBASE.dll, version: 6.1.7600.16385, time stamp: 0x4a5bdfe0 Exception code: 0xe0000003 Fault offset: 0x000000000000aa7d Faulting process id: 0xee8 Faulting application start time: 0x01cb9dc710fd76d8 Faulting application path: C:\Program Files\Microsoft Office\Office14\POWERPNT.EXE Faulting module path: C:\Windows\system32\KERNELBASE.dll Report Id: 58766562-09ba-11e0-90d1-00215a139192 And: Fault bucket , type 0 Event Name: APPCRASH Response: Not available Cab Id: 0 Problem signature: P1: POWERPNT.EXE P2: 14.0.4754.1000 P3: 4b967cf2 P4: KERNELBASE.dll P5: 6.1.7600.16385 P6: 4a5bdfe0 P7: e0000003 P8: 000000000000aa7d P9: P10: Attached files: C:\Users\marcusl\AppData\Local\Temp\CVR86DD.tmp.cvr C:\Users\marcusl\AppData\Local\Temp\WERC765.tmp.WERInternalMetadata.xml These files may be available here: C:\Users\marcusl\AppData\Local\Microsoft\Windows\WER\ReportArchive\AppCrash_POWERPNT.EXE_d45f313d77f7e52cc8682b2b64cc3898127c2c_1106e3ac Analysis symbol: Rechecking for solution: 0 Report Id: 58766562-09ba-11e0-90d1-00215a139192 Report Status: 1

  Read the article

• Conditional hotkey or include in AutoHotKey

  - by Bowen

  Is there a way to define a Hotkey conditionally in AutoHotKey? I want to do different keyboard mappings for different machines with different physical keyboards. This is what I want to do: RegRead, ComputerName, HKEY_LOCAL_MACHINE, System\CurrentControlSet\Control\ComputerName, ComputerName If ( ComputerName = BDWELLE-DIM8300 ) { #Include %A_ScriptDir%\Mappings-BDWELLE-DIM8300.ahk } OR RegRead, ComputerName, HKEY_LOCAL_MACHINE, System\CurrentControlSet\Control\ComputerName, ComputerName If ( ComputerName = BDWELLE-DIM8300 ) { LWin::LAlt [more hotkey definitions that only apply to this machine] } but since AHK parses Hotkey definitions and #Include statements BEFORE interpreting If statements, the Hotkeys definitions (whether buried in an #Include or not) do not respect the If condition. Thanks for pointing me to AutoHotKey_L! Do you have a specific example of how to conditionally define a hotkey? The syntax is very confusing. Here's what I'm trying (after having installed AutoHotKey_L.exe in place of AutoHotKey.exe): RegRead, ComputerName, HKEY_LOCAL_MACHINE, System\CurrentControlSet\Control\ComputerName, ComputerName #If ( ComputerName = BDWELLE-DIM8300 ) LWin::LAlt but that doesn't seem to work...

  Read the article

• Reverse SSH Tunnel

  - by chris

  I am trying to forward web traffic from a remote server to my local machine in order to test out some API integration (tropo, paypal, etc). Basically, I'm trying to setup something similar to what tunnlr.com provides. I've initiated the ssh tunnel with the command $ssh –nNT –R :7777:localhost:5000 user@server Then I can see that server has is now listening on port 7777 with user@server:$netstat -ant | grep 7777 tcp 0 0 127.0.0.1:7777 0.0.0.0:* LISTEN tcp6 0 0 ::1:7777 :::* LISTEN $user@server:curl localhost:7777 Hello from local machine So that works fine. The curl request is actually served from the local machine. Now, how do I enable server.com:8888 to be routed through that tunnel? I've tried using nginx like so: upstream tunnel { server 0.0.0.0:7777; } server { listen 8888; server_name server.com; location / { access_log /var/log/nginx/tunnel-access.log; error_log /var/log/nginx/tunnel-error.log; proxy_pass http://tunnel; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_redirect off; } } From the nginx error log I see: [error] 11389#0: *1 connect() failed (111: Connection refused) I've been looking at trying to use iptables, but haven't made any progress. iptables seems like a more elegant solution than running nginx just for tunneling. Any help is greatly appreciated. Thanks!

  Read the article

• Cisco 891w multiple VLAN configuration

  - by Jessica

  I'm having trouble getting my guest network up. I have VLAN 1 that contains all our network resources (servers, desktops, printers, etc). I have the wireless configured to use VLAN1 but authenticate with wpa2 enterprise. The guest network I just wanted to be open or configured with a simple WPA2 personal password on it's own VLAN2. I've looked at tons of documentation and it should be working but I can't even authenticate on the guest network! I've posted this on cisco's support forum a week ago but no one has really responded. I could really use some help. So if anyone could take a look at the configurations I posted and steer me in the right direction I would be extremely grateful. Thank you! version 15.0 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname ESI ! boot-start-marker boot-end-marker ! logging buffered 51200 warnings ! aaa new-model ! ! aaa authentication login userauthen local aaa authorization network groupauthor local ! ! ! ! ! aaa session-id common ! ! ! clock timezone EST -5 clock summer-time EDT recurring service-module wlan-ap 0 bootimage autonomous ! crypto pki trustpoint TP-self-signed-3369945891 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-3369945891 revocation-check none rsakeypair TP-self-signed-3369945891 ! ! crypto pki certificate chain TP-self-signed-3369945891 certificate self-signed 01 (cert is here) quit ip source-route ! ! ip dhcp excluded-address 192.168.1.1 ip dhcp excluded-address 192.168.1.5 ip dhcp excluded-address 192.168.1.2 ip dhcp excluded-address 192.168.1.200 192.168.1.210 ip dhcp excluded-address 192.168.1.6 ip dhcp excluded-address 192.168.1.8 ip dhcp excluded-address 192.168.3.1 ! ip dhcp pool ccp-pool import all network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 dns-server 10.171.12.5 10.171.12.37 lease 0 2 ! ip dhcp pool guest import all network 192.168.3.0 255.255.255.0 default-router 192.168.3.1 dns-server 10.171.12.5 10.171.12.37 ! ! ip cef no ip domain lookup no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO891W-AGN-A-K9 sn FTX153085WL ! ! username ESIadmin privilege 15 secret 5 $1$g1..$JSZ0qxljZAgJJIk/anDu51 username user1 password 0 pass ! ! ! class-map type inspect match-any ccp-cls-insp-traffic match protocol cuseeme match protocol dns match protocol ftp match protocol h323 match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udp class-map type inspect match-all ccp-insp-traffic match class-map ccp-cls-insp-traffic class-map type inspect match-any ccp-cls-icmp-access match protocol icmp class-map type inspect match-all ccp-invalid-src match access-group 100 class-map type inspect match-all ccp-icmp-access match class-map ccp-cls-icmp-access class-map type inspect match-all ccp-protocol-http match protocol http ! ! policy-map type inspect ccp-permit-icmpreply class type inspect ccp-icmp-access inspect class class-default pass policy-map type inspect ccp-inspect class type inspect ccp-invalid-src drop log class type inspect ccp-protocol-http inspect class type inspect ccp-insp-traffic inspect class class-default drop policy-map type inspect ccp-permit class class-default drop ! zone security out-zone zone security in-zone zone-pair security ccp-zp-self-out source self destination out-zone service-policy type inspect ccp-permit-icmpreply zone-pair security ccp-zp-in-out source in-zone destination out-zone service-policy type inspect ccp-inspect zone-pair security ccp-zp-out-self source out-zone destination self service-policy type inspect ccp-permit ! ! crypto isakmp policy 1 encr 3des authentication pre-share group 2 ! crypto isakmp client configuration group 3000client key 67Nif8LLmqP_ dns 10.171.12.37 10.171.12.5 pool dynpool acl 101 ! ! crypto ipsec transform-set myset esp-3des esp-sha-hmac ! crypto dynamic-map dynmap 10 set transform-set myset ! ! crypto map clientmap client authentication list userauthen crypto map clientmap isakmp authorization list groupauthor crypto map clientmap client configuration address initiate crypto map clientmap client configuration address respond crypto map clientmap 10 ipsec-isakmp dynamic dynmap ! ! ! ! ! interface FastEthernet0 ! ! interface FastEthernet1 ! ! interface FastEthernet2 ! ! interface FastEthernet3 ! ! interface FastEthernet4 ! ! interface FastEthernet5 ! ! interface FastEthernet6 ! ! interface FastEthernet7 ! ! interface FastEthernet8 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto ! ! interface GigabitEthernet0 description $FW_OUTSIDE$$ES_WAN$ ip address 10...* 255.255.254.0 ip nat outside ip virtual-reassembly zone-member security out-zone duplex auto speed auto crypto map clientmap ! ! interface wlan-ap0 description Service module interface to manage the embedded AP ip unnumbered Vlan1 arp timeout 0 ! ! interface Wlan-GigabitEthernet0 description Internal switch interface connecting to the embedded AP switchport trunk allowed vlan 1-3,1002-1005 switchport mode trunk ! ! interface Vlan1 description $ETH-SW-LAUNCH$$INTF-INFO-FE 1$$FW_INSIDE$ ip address 192.168.1.1 255.255.255.0 ip nat inside ip virtual-reassembly zone-member security in-zone ip tcp adjust-mss 1452 crypto map clientmap ! ! interface Vlan2 description guest ip address 192.168.3.1 255.255.255.0 ip access-group 120 in ip nat inside ip virtual-reassembly zone-member security in-zone ! ! interface Async1 no ip address encapsulation slip ! ! ip local pool dynpool 192.168.1.200 192.168.1.210 ip forward-protocol nd ip http server ip http access-class 23 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ! ! ip dns server ip nat inside source list 23 interface GigabitEthernet0 overload ip route 0.0.0.0 0.0.0.0 10.165.0.1 ! access-list 23 permit 192.168.1.0 0.0.0.255 access-list 100 remark CCP_ACL Category=128 access-list 100 permit ip host 255.255.255.255 any access-list 100 permit ip 127.0.0.0 0.255.255.255 any access-list 100 permit ip 10.165.0.0 0.0.1.255 any access-list 110 permit ip 192.168.0.0 0.0.5.255 any access-list 120 remark ESIGuest Restriction no cdp run ! ! ! ! ! ! control-plane ! ! alias exec dot11radio service-module wlan-ap 0 session Access point version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname ESIRouter ! no logging console enable secret 5 $1$yEH5$CxI5.9ypCBa6kXrUnSuvp1 ! aaa new-model ! ! aaa group server radius rad_eap server 192.168.1.5 auth-port 1812 acct-port 1813 ! aaa group server radius rad_acct server 192.168.1.5 auth-port 1812 acct-port 1813 ! aaa authentication login eap_methods group rad_eap aaa authentication enable default line enable aaa authorization exec default local aaa authorization commands 15 default local aaa accounting network acct_methods start-stop group rad_acct ! aaa session-id common clock timezone EST -5 clock summer-time EDT recurring ip domain name ESI ! ! dot11 syslog dot11 vlan-name one vlan 1 dot11 vlan-name two vlan 2 ! dot11 ssid one vlan 1 authentication open eap eap_methods authentication network-eap eap_methods authentication key-management wpa version 2 accounting rad_acct ! dot11 ssid two vlan 2 authentication open guest-mode ! dot11 network-map ! ! username ESIadmin privilege 15 secret 5 $1$p02C$WVHr5yKtRtQxuFxPU8NOx. ! ! bridge irb ! ! interface Dot11Radio0 no ip address no ip route-cache ! encryption vlan 1 mode ciphers aes-ccm ! broadcast-key vlan 1 change 30 ! ! ssid one ! ssid two ! antenna gain 0 station-role root ! interface Dot11Radio0.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface Dot11Radio0.2 encapsulation dot1Q 2 no ip route-cache bridge-group 2 bridge-group 2 subscriber-loop-control bridge-group 2 block-unknown-source no bridge-group 2 source-learning no bridge-group 2 unicast-flooding bridge-group 2 spanning-disabled ! interface Dot11Radio1 no ip address no ip route-cache shutdown ! encryption vlan 1 mode ciphers aes-ccm ! broadcast-key vlan 1 change 30 ! ! ssid one ! antenna gain 0 dfs band 3 block channel dfs station-role root ! interface Dot11Radio1.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface GigabitEthernet0 description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router no ip address no ip route-cache ! interface GigabitEthernet0.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled ! interface GigabitEthernet0.2 encapsulation dot1Q 2 no ip route-cache bridge-group 2 no bridge-group 2 source-learning bridge-group 2 spanning-disabled ! interface BVI1 ip address 192.168.1.2 255.255.255.0 no ip route-cache ! ip http server no ip http secure-server ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag access-list 10 permit 192.168.1.0 0.0.0.255 radius-server host 192.168.1.5 auth-port 1812 acct-port 1813 key ***** bridge 1 route ip

  Read the article

• OpenVPN and TomatoVPN

  - by Bill Johnson

  Wondering if someone can help me with the following. I have updated my Linksys router with TomatoVPN and used the following config: Interface Type:TAP Protocol:UDP Port:1195 Firewall Custom Authorization Mode:Static Key I have then inserted the static key generated in OpenVPN saved and started the service. connect.ovpn. # Use the following to have your client computer send all traffic through your router # (remote gateway) remote (entered my DNS/DHCP servers external IP address here) port 1195 dev tap secret static.key.txt proto udp comp-lzo route-gateway 192.168.1.1 redirect-gateway float I've then placed my static key in a file in the same directory as your connect.ovpn (static.key.txt) Now OpenVPN is installed on a laptop that I use at home. I have plugged in the laptop to my home connection and started connect.ovpn The Local Area Connection is connected as 'Home Network 3' - and when I start OpenVPN it is connected as 'Local Area Connection 2' and this is showing as 'Unidentified Network' and it appears there is no network access. TAP-Win32 Adapter V9 appears to be the adaptors name and the IP and DNS properties are set to automatic. If I open up the OpenVPN GUI it shows an error message saying "Connecting to connect has failed". Looking at the error message behind this pop-up one line says "TCP/UDP Socket bind failed on local address [undef]:1195 Address already in use [WSAEADDRINUSE] Could anyone possibly help me further with this please?

  Read the article

• Fox Pro Database File Locked by Shadow Copy?

  - by leeand00

  I'm using Process Explorer to determine what process has a lock on a particular Fox Pro Database file in windows. It's telling me that System has a lock on it. When I go to kill the "System" process (which if you ask me doesn't sound like a very good idea), it asks me if I'm sure I want to kill the System process. I haven't answered yes yet. It's a company server, and I'm thinking that maybe my only option is to tell everybody to get off of it and reboot. Do I have any other options?

  Read the article

• Keyboard doesn't work after upgrade to Debian Wheezy

  - by mikhail

  After upgrade from lenny to wheezy keyboard and mouse don't work in X (keyboard available before it starts). I looked over internet about this issue and found some solutions: remove xorg.conf (http://forums.debian.net/viewtopic.php?f=7&t=62880) update udev and base-files (http://forums.debian.net/viewtopic.php?f=6&t=64927&p=376136#p376136) remove /run directory (http://forums.debian.net/viewtopic.php?f=6&t=64927&p=376136#p376136) reintall xserver and xorg But, nothing helped me :( Logs of X-server haven't got any messages about keyboard or mouse errors. Below you can see configuration of my system: krestyaninov@xxx# uname -a Linux xxx 3.0.0-1-686-pae #1 SMP Sat Aug 27 16:41:03 UTC 2011 i686 GNU/Linux krestyaninov@xxx# dpkg -l |grep udev ii libgudev-1.0-0 172-1 GObject-based wrapper library for libudev ii libudev0 172-1 libudev shared library ii udev 172-1 /dev/ and hotplug management daemon krestyaninov@xxx# dpkg -l |grep base-files ii base-files 6.5 Debian base system miscellaneous files krestyaninov@xxx# dpkg -l |grep xorg ii xorg 1:7.6+8 X.Org X Window System ... ii xserver-xorg 1:7.6+8 X.Org X server

  Read the article

• Project Server 2007 install issue - ProjectEventService won't start

  - by Brian Meinertz

  Trying to install PS2007 with SP1 on Server 2003. The install goes fine, but when running the SharePoint Configuration Wizard, it fails at stage 6 of 12 with the error: Failed to register SharePoint Services. An exception of type System.InvalidOperationException was thrown. Additional exception information: Cannot start service ProjectEventService on computer '.'. From the PSCDiagnostics log: Exception: System.InvalidOperationException: Cannot start service ProjectEventService on computer '.'. --- System.ComponentModel.Win32Exception: The service did not respond to the start or control request in a timely fashion. The ProjectEventService (Microsoft Office Project Server Event) won't even start manually using the Network Service account. Starting the service with a domain account works, but subsequently running the Config Wizard causes the service to be removed and re-provisioned to run using the Network Service account, which again fails. Presumably Network Service needs elevated permissions, but even adding it to the local Admin group makes no difference. Anyone come across this sort of issue before?

  Read the article

• Hylafax: Encounter "No font metric information" when try to send a fax

  - by Chau Chee Yang

  I am using Hylafax 6.0.5 on Fedora 13 x86_64. As there are no rpm package available for Fedora 13, I use the source tar ball to install hylafax myself. Everything seems fine during compile and install. I try to send a fax with sendfax and encounter error: # sendfax -n -d <fax-number> /etc/passwd /usr/local/sbin/textfmt: No font metric information found for "Courier-Bold". Usage: /usr/local/sbin/textfmt [-1] [-2] [-B] [-c] [-D] [-f fontname] [-F fontdir(s)] [-m N] [-o #] [-p #] [-r] [-U] [-Ml=#,r=#,t=#,b=#] [-V #] files... >out.ps Default options: -f Courier -1 -p 11bp -o 0 Error converting document; command was "/usr/local/sbin/textfmt -B -f Courier-Bold -Ml=0.4in -p 11 -s default >'/tmp//sndfaxp5GdJ9' <'/etc/passwd'" It seems like there is problem with font problem. I have ghostscript-fonts installed too. I can't find hyla.conf in path /etc/hylafax. There is no /etc/hylafax path in my file system. All configuration files seems located in /var/spool/hylafax/etc. Please advice. Thank you.

  Read the article

• Remove Downed Exchange Server from First Administrative Group

  - by Campo

  I had a server die. It is gone forever. It is still listed in the servers folder of the first administrative group in the Exchange System Manager. When I click "all tasks Remove Server" I get the following error: The Server "SERVERNAME" cannot be removed because: -One or more users currently use a mailbox on this server. These users must be moved to a mailbox store on a different server or be mail disabled before uninstalling this server. Facility: Exchange System Manager ID no: c103f492 Exchange System Manager Any help would be MUCH appreciated. I cannot access the mailbox stores anymore and I do not care about the lost mailboxes. We deleted the inactive and old users as well. So I am stumped on this one. I just need to remove the old machine. THANKS!

  Read the article

• Setting Ubuntu Global PATH for Ruby Enterprise Edition

  - by Wally Glutton

  Context: I recently installed Ruby Enterprise Edition (REE) on an Ubuntu 8.04 server. I would like for this new version of Ruby to globally supersede (for all users, crontabs, etc) the older version in /usr/local/bin. Attempted Solution #1: The REE documentation recommends placing the REE bin folder at the beginning of the global PATH in /etc/environment. I altered the PATH line in this file to read: PATH="/opt/ruby_ee/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games" This did affect my PATH at all. Attempted Solution #2: Next I followed these instructions and updated the PATH setting in the /etc/login.defs and /etc/crontab files. (I did not change /etc/sudoers.) This didn't affect my PATH either, even after logging out and rebooting the server. Other information: I seem to be having the same problem described here. I'm testing using the command: echo $PATH My shell is bash. My .bashrc doesn't not alter my PATH. I'm ssh'ed into the system for all testing. /opt/ruby_ee/ is a sym-link to /opt/ruby-enterprise-1.8.7-2011.03/

  Read the article

• Alfresco Community Edition Consultants

  - by Talkincat

  I am in the process of putting together an document management system based on Alfresco Community 3.2r2. Because Alfresco will not allow its partners to work with the Community edition, I have found it devilishly tricky to find consultants that specialize in Alfresco to help me with this project. Can anyone point me in the direction of someone that can help me get this system up an running? I will mostly need help with integrating Alfresco with Active Directory (LDAP passthrough, user/group sync and SSO) and performance tuning the system. Any help is greatly appreciated.

  Read the article

• Powershell script to send e-mails, losing text in e-mail attachment

  - by Beuy

  I have the following function to send e-mails in powershell with attachments: function SendMail(){ if($e -ine '') { $mail = New-Object System.Net.Mail.MailMessage $mail.From = $f; $mail.To.Add($t); $mail.Subject = $s; $att = New-Object System.Net.Mail.Attachment –ArgumentList $l $mail.Attachments.Add($att) $mail.Body = $b; $smtp = New-Object System.Net.Mail.SmtpClient($serv); $smtp.Send($mail); } } When I try to send a .txt file attachment it seems to strip out all of the information from within the text file. Any suggestions as to what's going wrong?

  Read the article

• Add a custom certificate authority to Ubuntu

  - by rmrobins

  Hello; I have created a custom root certificate authority for an internal network, example.com. Ideally, I would like to be able to deploy the CA certificate associated with this certificate authority to my Linux clients (running Ubuntu 9.04 and CentOS 5.3), such that all of the applications automatically recognize the certificate authority (i.e. I do not want to have to configure Firefox, Thunderbird, etc manually to trust this certificate authority). I have attempted this on Ubuntu by copying the PEM-encoded CA certificate to /etc/ssl/certs/ and /usr/share/ca-certificates/, as well as by modifying /etc/ca-certificates.conf and rerunning update-ca-certificates, however applications do not seem to recognize that I have added another trusted CA to the system. Therefore, is it possible to add a CA certificate once to a system, or is it necessary to manually add the CA to all of the possible applications that will attempt to make SSL connections to hosts signed by this CA in my network? If it is possible to add a CA certificate once to the system, where does it need to go? Thanks.

  Read the article

• Restart Fibre channel controller after blade bootup IBM HS bladecentre

  - by Spence

  I have a remote system that needs to resume on startup. If the system is simply powered on then the blades boot before the SAN is online and then the only thing you can do is restart the systems. Is it possible to restart the fibre channel controller? That way I could have a system restart the controller after boot, connect to the SAN and then restart all servers requiring SAN information? Please note that I'm not a sys admin, just shooting for ideas to get a clean startup to work, apologies if my terminology is wrong.

  Read the article

• Vista ICS issue

  - by Bill Grey

  I have a strange problem with Internet Connection Sharing on a laptop running Vista Business. This laptop is connected to the internet via the ethernet port, which goes to an ADSL modem. it is automatically assigned the IP address 192.168.1.50, and the modem/gateway is 192.168.1.1 My friends laptop is running Vista Home. Previously, I would create an ad hoc wireless network, enable ICS, and everything would be perfect. My friend would have internet access via this. However, something has now mysteriously broken. If I enable ICS on the wireless connection, it resets my Local Area Connection, assigning it the manual IP address of 192.168.0.1, which means my connection to the internet is destroyed. Both wireless adapters on each network are assigned auto configuration addresses, in the 168. range. They can see each other fine, but my friends laptop cannot access the internet via mine, even after I have restored the Local Area Connection settings. I understand the computer with ICS enabled must have the IP of 192.168.0.1, but previously, before whatever went wrong, my wireless adapter would be 192.168.0.1 and my friends computer would get an IP via DHCP. I have also tried setting static IP address and making a bridge, none of which works. How can I fix this problem, and prevent enabling ICS from touching my Local Area Connection? Both machines have no firewall, have appropriate settings etc...

  Read the article

• MySQL socket connections working, but not port connections

  - by Neil

  I installed MySQL community 5.1.45 on my Snow Leopard 10.6, using the pkg from their site. I had previously installed a MySQL binary from entropy.ch. In the previous installation, the connections were working fine before I upgrade to Snow Leopard. In Snow Leopard, both the installations are problematic. Using an app called Sequel Pro, if I connect with the socket operation, it connects properly. However, a standard connection with the same credentials doesn't work. From what I've understood, socket connections happen on the machine itself between processes, whereas normal connections occur over the network/ports, in this case a loopback to my machine, since the server and client are both on the same machine. My new CakePHP installation isn't being able to connect to the db with the root credentials I provided. Btw, I've been starting the MySQL server using the Preference Pane. When I tried running mysqld from terminal, it gave me: 100323 1:54:37 [Warning] Can't create test file /usr/local/mysql-5.1.45-osx10.6-x86_64/data/mbp.lower-test 100323 1:54:37 [Warning] Can't create test file /usr/local/mysql-5.1.45-osx10.6-x86_64/data/mbp.lower-test mysqld: Can't change dir to '/usr/local/mysql-5.1.45-osx10.6-x86_64/data/' (Errcode: 13) 100323 1:54:37 [ERROR] Aborting 100323 1:54:37 [Note] mysqld: Shutdown complete mbp is the name of my machine. How do I fix this so that my webserver can connect to the mysql server?

  Read the article

• configuration transfer over scp on commit not working on Juniper EX-2200 switch

  - by liv2hak

  I am making a series of configuration changes on Junos EX- 2200 switch.I have this router connected to another PC via an ethernet cable.The IP address of the switch is 192.168.1.1.I am able to ping from 192.168.1.1 to 192.168.1.0 and vice-versa. After the changes I make I do the following commands set system archival configuration transfer-on-commit set system archival configuration archive-sites "scp://[email protected]:/home/karthik/ws_karthik/sw1_config_1.txt" password godfather commit Where there is a user with user-name "karthik " and password "godfather".The path shown above also exists in the system How ever I don't see the configuration file sw1_config_1.txt created at the path specified. Also I have verified that sshd is running on the PC (192.168.1.10) Am I doing something wrong here? It would be great if anyone could help me out.

  Read the article

• Nexenta/OpenSolaris filer kernel panic/crash

  - by ewwhite

  I've an x4540 Sun storage server running NexentaStor Enterprise. It's serving NFS over 10GbE CX4 for several VMWare vSphere hosts. There are 30 virtual machines running. For the past few weeks, I've had random crashes spaced 10-14 days apart. This system used to open OpenSolaris and was stable in that arrangement. The crashes trigger the automated system recovery feature on the hardware, forcing a hard system reset. Here's the output from mdb debugger: panic[cpu5]/thread=ffffff003fefbc60: Deadlock: cycle in blocking chain ffffff003fefb570 genunix:turnstile_block+795 () ffffff003fefb5d0 unix:mutex_vector_enter+261 () ffffff003fefb630 zfs:dbuf_find+5d () ffffff003fefb6c0 zfs:dbuf_hold_impl+59 () ffffff003fefb700 zfs:dbuf_hold+2e () ffffff003fefb780 zfs:dmu_buf_hold+8e () ffffff003fefb820 zfs:zap_lockdir+6d () ffffff003fefb8b0 zfs:zap_update+5b () ffffff003fefb930 zfs:zap_increment+9b () ffffff003fefb9b0 zfs:zap_increment_int+68 () ffffff003fefba10 zfs:do_userquota_update+8a () ffffff003fefba70 zfs:dmu_objset_do_userquota_updates+de () ffffff003fefbaf0 zfs:dsl_pool_sync+112 () ffffff003fefbba0 zfs:spa_sync+37b () ffffff003fefbc40 zfs:txg_sync_thread+247 () ffffff003fefbc50 unix:thread_start+8 () Any ideas what this means?

  Read the article

• Getting Error while running RED5 server - class path resource [red5.xml] cannot be opened because it does not exist

  - by sunil221

  HI , I have installed java version "1.6.0_14" and Ant version 1.8.2 for red5 Server. when i am trying to run red5 server i am getting the following error please help Root: /usr/local/red5 Deploy type: bootstrap Logback selector: org.red5.logging.LoggingContextSelector Setting default logging context: default 11:27:39.838 [main] INFO org.red5.server.Launcher - Red5 Server 1.0.0 RC1 $Rev: 4171 $ (http://code.google.com/p/red5/) Red5 Server 1.0.0 RC1 $Rev: 4171 $ (http://code.google.com/p/red5/) SLF4J: Class path contains multiple SLF4J bindings. SLF4J: Found binding in [jar:file:/usr/local/red5/red5.jar!/org/slf4j/impl/StaticLoggerBinder.class] SLF4J: Found binding in [jar:file:/usr/local/red5/lib/logback-classic-0.9.26.jar!/org/slf4j/impl/StaticLoggerBinder.class] SLF4J: See http://www.slf4j.org/codes.html#multiple_bindings for an explanation. 11:27:39.994 [main] INFO o.s.c.s.FileSystemXmlApplicationContext - Refreshing org.springframework.context.support.FileSystemXmlApplicationContext@39d85f79: startup date [Mon Dec 21 11:27:39 EST 2009]; root of context hierarchy 11:27:40.149 [main] INFO o.s.b.f.xml.XmlBeanDefinitionReader - Loading XML bean definitions from class path resource [red5.xml] Exception org.springframework.beans.factory.BeanDefinitionStoreException: IOException parsing XML document from class path resource [red5.xml]; nested exception is java.io.FileNotFoundException: class path resource [red5.xml] cannot be opened because it does not exist Bootstrap complete

  Read the article

• Sharepoint 2007 Event ID 6482

  - by Dave M

  Our two server SharePoint 2007 SP2 farm has an issue. Event ID 6482 appears in the Application log of the Web front end many times a day. Often many time a minute. The full error is from Office SharePoint Server Event Type: Error Event Source: Office SharePoint Server Event Category: Office Server Shared Services Event ID: 6482 Date: 11/12/2009 Time: 3:05:22 PM User: N/A Computer: XXXXXX Description: Application Server Administration job failed for service instance Microsoft.Office.Server.Search.Administration.SearchServiceInstance (36a9b7ef-59aa-4f94-8887-8bf7b56f2f91). Reason: Error during encryption or decryption. System error code 0. Techinal Support Details: System.ArgumentException: Error during encryption or decryption. System error code 0. at Microsoft.Office.Server.Search.Administration.SearchServiceInstance.SynchronizeDefaultContentSource(IDictionary applications) at Microsoft.Office.Server.Search.Administration.SearchServiceInstance.Synchronize() at Microsoft.Office.Server.Administration.ApplicationServerJob.ProvisionLocalSharedServiceInstances(Boolean isAdministrationServiceJob) For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. The SharePoint site appears to be functioning normally and Search returns expected results. Any suggestions would be appreciated

  Read the article

• Freeradius authentication failed for unknown reason

  - by Moein7tl

  I followed this instruction to force freeradius to use mysql database. and run freeradius in debug mod. but it rejects all authentication. mysql database : mysql select * from radcheck; +----+----------+-----------+----+---------+ | id | username | attribute | op | value | +----+----------+-----------+----+---------+ | 1 | test | Password | == | test123 | | 2 | test | Auth-Type | == | Local | +----+----------+-----------+----+---------+ 2 rows in set (0.02 sec) radtest command : # radtest test test123 localhost 0 testing123 Sending Access-Request of id 235 to 127.0.0.1 port 1812 User-Name = "test" User-Password = "test123" NAS-IP-Address = 127.0.0.1 NAS-Port = 0 Message-Authenticator = 0x00000000000000000000000000000000 rad_recv: Access-Reject packet from host 127.0.0.1 port 1812, id=235, length=20 radiusd debug mod log: rad_recv: Access-Request packet from host 127.0.0.1 port 51034, id=235, length=74 User-Name = "test" User-Password = "test123" NAS-IP-Address = 127.0.0.1 NAS-Port = 0 Message-Authenticator = 0xbf111cbbae24fb0f0a558bfa26f53476 # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop ++[digest] returns noop [suffix] No '@' in User-Name = "test", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] No EAP-Message, not doing EAP ++[eap] returns noop ++[files] returns noop ++[expiration] returns noop ++[logintime] returns noop [pap] WARNING! No "known good" password found for the user. Authentication may fail because of this. ++[pap] returns noop ERROR: No authenticate method (Auth-Type) found for the request: Rejecting the user Failed to authenticate the user. Using Post-Auth-Type Reject # Executing group from file /usr/local/etc/raddb/sites-enabled/default +- entering group REJECT {...} [attr_filter.access_reject] expand: %{User-Name} - test attr_filter: Matched entry DEFAULT at line 11 ++[attr_filter.access_reject] returns updated Delaying reject of request 20 for 1 seconds Going to the next request Waking up in 0.9 seconds. Sending delayed reject for request 20 Sending Access-Reject of id 235 to 127.0.0.1 port 51034 Waking up in 4.9 seconds. Cleaning up request 20 ID 235 with timestamp +4325 Ready to process requests. where is the problem and how should I solve it?

  Read the article

• Application losing Printer within Terminal Services for remote users

  - by Richard

  Question: What I need to do is have a permanent link to a printer, normally only accessible through Terminal Services (Printer Redirect), to allow Sage Line 50 layouts to see that printer persistently, even after users have disconnected and reconnected to the Terminal Services session? Although the printer is accessible each time a user connects to the Sage Server via Terminal Services, it is given a different session number and therefore the Sage Layout sees it as a different printer. History behind question: Users using Terminal Services connecting to a Sage Server on a different site Using Sage Line 50 v 15 on that Server Users want to print invoices (sage layouts) locally Sage Server cannot see the users local printers, to get around this user uses the Print redirect features of Terminal Services The individual reports can be edited to point to a specific printer by default. This means the user just has to select an invoice and click print, then select the layout/report wanted and it auto prints that invoice to the default printer specified. The problem occurs because the layouts are edited to point to the users local printer "Ricoh 1018d (session#)", note the "(session#)" as this is the users local printer being redirected through the terminal services session. Users are able to print using the sage layouts once the default printer is setup within the layout and saved, but as soon as the users disconnects from the Terminal Services session and then reconnect in the morning go to print, it has lost the connection to that printer. I understand why its failed, because that the printer is on a per session basis and the layout would not be able to hold on to the connection from a previous session. Thanks in advance for any assistance...

  Read the article

• How do I get Windows 7 To Recognize a newly installed RAID 5 volume?

  - by GregH

  I had a previously running Windows 7 (64 bit) system. I added 3 new 1TB Seagate drives that I set up as a RAID 5 volume. I have a Gigabyte GA-P55M-UD2 motherboard. I installed the drives, set up the BIOS and configured the three drives as a RAID volume through the RAID setup utility that was accessed via Ctrl-I while the system was booting. I rebooted the system and could see the drives during the boot sequence. However, when Windows 7 was starting I got an error (quick blue screen) and then Windows tried to repair itself with no success. Do I need to install RAID drivers in Windows? How do I do it if Windows won't boot? Thanks in advance.

  Read the article

< Previous Page | 516 517 518 519 520 521 522 523 524 525 526 527  | Next Page >