Search Results

Search found 22968 results on 919 pages for 'stuck again'.

Page 522/919 | < Previous Page | 518 519 520 521 522 523 524 525 526 527 528 529  | Next Page >

• Mounting NAS share: Bad Address

  - by Korben

  I've faced to the problem that can't solve. Hope you can help me with it. I have a storage QNAP TS-459U, with it's own Linux, and 'massive1' folder shared, which I need to mount to my Debian server. They are connected by regular patch cord. Debian server has two network interfaces - eth0 and eth1. eth0 is for Internet, eth1 is for QNAP. So, I'm saying this: mount -t cifs //169.254.100.100/massive1/ /mnt/storage -o user=admin , where 169.254.100.100 is an IP of QNAP's interface. The result I get (after entering password): mount error(14): Bad address Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) Tried: mount.cifs, smbmount, with '/' at the end of the network share and without it, and many other variations of that command. And always its: mount error(14): Bad address Funny thing is when I was in Data Center, I had connected my netbook to QNAP by the same scheme (with Fedora 16 on it), and it connected without any problems, I could read/write files on the QNAP's NAS share! So I'm really stuck with the Debian. I can't undrestand where's the difference with Fedora, making this error. Yeah, I've used Google. Couldn't find any useful info. Ping to the QNAP's IP is working, I can log into QNAP's Linux by ssh, telnet on 139's port is working. This is network interface configuration I use in Debian: IP: 169.254.100.1 Netmask: 255.255.0.0 The only diffence in connecting to Fedora and Debian is that in Fedora I've added gateway - 169.254.100.129, but ping to this IP is not working, so I think it's not necessary at all. P.S. ~# cat /etc/debian_version wheezy/sid ~# uname -a Linux host 2.6.32-5-openvz-amd64 #1 SMP Mon Mar 7 22:25:57 UTC 2011 x86_64 GNU/Linux ~# smbtree WORKGROUP \\HOST host server \\HOST\IPC$ IPC Service (host server) \\HOST\print$ Printer Drivers NAS \\MASSIVE1 NAS Server \\MASSIVE1\IPC$ IPC Service (NAS Server) \\MASSIVE1\massive1 \\MASSIVE1\Network Recycle Bin 1 [RAID5 Disk Volume: Drive 1 2 3 4] \\MASSIVE1\Public System default share \\MASSIVE1\Usb System default share \\MASSIVE1\Web System default share \\MASSIVE1\Recordings System default share \\MASSIVE1\Download System default share \\MASSIVE1\Multimedia System default share Please, help me with solving this strange issue. Thanks before.

  Read the article

• Static IP on FEDORA12 from Virtualbox

  - by Krazy_Kaos

  I'm trying to get my FEDORA12 to have an STATIC IP - inside virtualbox - inside Ubuntu Let me rephrase that. I have an Ubuntu 9.04 system with vitualbox and a FEDORA12 vm there and I would like to put the fedora with an STATIC IP (amahi needs it), but I'm getting stuck... I'm using NAT (if that's any help) I tryid a few tutorials, but no go. I'm kind of new to the *nix world but I'm old school on M$ Edit: Screenshots UBUNTU 9.04 (host that has the vm) FEDORA (sory cant post pics... not enough rep) INFO: GUEST WITH STATIC: IFCONFIG: eth0 Link encap:Ethernet HWaddr 08:00:27:35:CC:DE inet addr:192.168.1.55 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe35:ccde/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7 errors:0 dropped:0 overruns:0 frame:0 TX packets:2764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574 (574.0 b) TX bytes:127121 (124.1 KiB) Interrupt:11 Base address:0xc020 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1856 errors:0 dropped:0 overruns:0 frame:0 TX packets:1856 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:181587 (177.3 KiB) TX bytes:181587 (177.3 KiB) NETSTAT -NR: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.2.1 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 GUEST WITH DHCP: IFCONFIG: eth0 Link encap:Ethernet HWaddr 08:00:27:35:CC:DE inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe35:ccde/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:105 errors:0 dropped:0 overruns:0 frame:0 TX packets:2966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:49787 (48.6 KiB) TX bytes:149969 (146.4 KiB) Interrupt:11 Base address:0xc020 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1903 errors:0 dropped:0 overruns:0 frame:0 TX packets:1903 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:185931 (181.5 KiB) TX bytes:185931 (181.5 KiB) NETSTAT -NR: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.0.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 10.0.2.2 0.0.0.0 UG 0 0 0 PS.: I'm still trying to workout the sudoer file to be able to exec the iptables command

  Read the article

• Lighttpd 403 Errors on HTML and PHP pages

  - by Brian

  I installed lighttpd on CentOS 5.5 64-bit. Everything seems fine and running except I cannot get past 403 errors on both HTML and PHP pages. I have used CHMOD and CHOWN, changed ownership in the config file, done everything possible and have been stuck for 2 days. Appreciate any help, and here's hoping to a stupid error on my part. Here is the log file with debug options on: 2011-02-21 11:23:13: (request.c.304) fd: 7 request-len: 408 GET /index.html HTTP/1.1 Host: 10.0.1.8 User-Agent: Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.6; en-US; rv:1.9.2.13) Gecko/20101203 Firefox/3.6.13 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 115 Connection: keep-alive Cache-Control: max-age=0 2011-02-21 11:23:13: (response.c.241) run condition 2011-02-21 11:23:13: (response.c.300) -- splitting Request-URI 2011-02-21 11:23:13: (response.c.301) Request-URI : /index.html 2011-02-21 11:23:13: (response.c.302) URI-scheme : http 2011-02-21 11:23:13: (response.c.303) URI-authority: 10.0.1.8 2011-02-21 11:23:13: (response.c.304) URI-path : /index.html 2011-02-21 11:23:13: (response.c.305) URI-query : 2011-02-21 11:23:13: (response.c.349) -- sanatising URI 2011-02-21 11:23:13: (response.c.350) URI-path : /index.html 2011-02-21 11:23:13: (response.c.470) -- before doc_root 2011-02-21 11:23:13: (response.c.471) Doc-Root : /srv/www/lighttpd 2011-02-21 11:23:13: (response.c.472) Rel-Path : /index.html 2011-02-21 11:23:13: (response.c.473) Path : 2011-02-21 11:23:13: (response.c.521) -- after doc_root 2011-02-21 11:23:13: (response.c.522) Doc-Root : /srv/www/lighttpd 2011-02-21 11:23:13: (response.c.523) Rel-Path : /index.html 2011-02-21 11:23:13: (response.c.524) Path : /srv/www/lighttpd/index.html 2011-02-21 11:23:13: (response.c.541) -- logical -> physical 2011-02-21 11:23:13: (response.c.542) Doc-Root : /srv/www/lighttpd 2011-02-21 11:23:13: (response.c.543) Rel-Path : /index.html 2011-02-21 11:23:13: (response.c.544) Path : /srv/www/lighttpd/index.html 2011-02-21 11:23:13: (response.c.561) -- handling physical path 2011-02-21 11:23:13: (response.c.562) Path : /srv/www/lighttpd/index.html 2011-02-21 11:23:13: (response.c.608) -- access denied 2011-02-21 11:23:13: (response.c.609) Path : /srv/www/lighttpd/index.html 2011-02-21 11:23:13: (response.c.128) Response-Header: HTTP/1.1 403 Forbidden Content-Type: text/html Content-Length: 345 Date: Mon, 21 Feb 2011 16:23:13 GMT Server: lighttpd/1.4.28 Here is the directory listing. I used CHOWN to set to lighttpd:lighttpd [root@localhost lighttpd]# ls -al total 40 drwxrwxrwx 2 lighttpd lighttpd 4096 Feb 21 10:48 . drwxrwxrwx 3 lighttpd lighttpd 4096 Feb 21 10:57 .. -rwxrwxrwx 1 lighttpd lighttpd 10 Feb 20 08:32 index.html -rwxrwxrwx 1 lighttpd lighttpd 20 Feb 21 10:48 index.php -rwxrwxrwx 1 lighttpd lighttpd 20 Feb 21 10:39 info.php [root@localhost lighttpd]# Requested Commands: [root@localhost lighttpd]# ls -ld / /srv /srv/www drwxr-xr-x 22 root root 4096 Feb 21 04:39 / drwxrwxrwx 3 lighttpd lighttpd 4096 Feb 20 07:38 /srv drwxrwxrwx 3 lighttpd lighttpd 4096 Feb 21 10:57 /srv/www [root@localhost lighttpd]# ps auxZ | grep lighttpd root:system_r:httpd_t lighttpd 3842 0.0 0.2 48368 896 ? S 12:24 0:00 /usr/sbin/lighttpd -f /etc/lighttpd/lighttpd.conf root:system_r:unconfined_t:SystemLow-SystemHigh root 3845 0.0 0.2 61152 764 pts/0 R+ 12:24 0:00 grep lighttpd

  Read the article

• using own mail server with external domain and dns. Now have internal dns. dkim test not working

  - by mojotaker

  I am not very knowledgeable in this area, but have been able to make great head way. Now i am stuck I setup my own mail server, e.g mailbox.example.com. I had the domain dns point to my mail server in my office. i was able to set up everything working fine. such as dkim and spf records. Recently i decided to setup an internal dns server in the office so as to resolve some addresses for some development servers internally. Ok the problem now is my mail server is sitting on the internal dns server (the mail server is on the same box as the dns server) its still able to send and receive emails but not sure if dkim is working properly. when i try to do a dkim test "amavisd test keys" i get "invalid (public key: not available)" and i know that that means i have a dns issue. so what should i do? I am currently looking at my internal dns zonefile and i dont know what to do (i am using bind dns server on an ubuntu-server box). do i configure a dkim txt record on the local dns ? or is there a way to forward dkim "request" to the external dns ? or do i have this whole thing done wrong ? To be clear Basically my internal domain name is the same as my external domain name (i.e example.com) i have a mail server within my internal domain mailbox.example.com, that uses my external domain dns (external dns has been setup to point to my emailserver (which of course is now sitting behind my internal dns)) dkim (i dont think its working because it fails the dkim test") Need help in determing the proper setup What is the proper way to set this up ? thank you Update: Here is my local dns zone file ; ; BIND data file for local loopback interface ; $TTL 604800 @ IN SOA webserver.example.com. root.example.com. ( //dns and webserver on the same box 2012030809 ; Serial 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; @ IN NS webserver.example.com. @ IN A 192.168.1.117 @ IN AAAA ::1 ns IN A 192.168.1.117 www IN A xx.xx.xx.xxx // ip of external domain box (bluehost) work around to let local clients access website newsletter IN A xx.xx.xxx.117 // external ip address of local network mailbox.example.com. IN A 192.168.1.111 // internal ip of mailbox (mailserver webserver.example.com. IN A 192.168.1.117 //internal ip of a webserver

  Read the article

• How to reinstall OEM Windows 98 SE?

  - by Sammy

  I'm trying to install Windows 98 SE on an old PC and it's not going well. I run into this problem. Searching for Boot Record from Floppy..OK Starting Windows 98... TOSHIBA Enhanced-IDE CD/DVD-ROM Device Driver (ATAPI) Version 2.24 (C)Copyright Toshiba Corp. 1995-1999. All rights reserved. Device Name : TOSCD001 Number of units : 1 MSCDEX Version 2.25 Copyright (C) MIcrosoft Corp. 1986-1995. All rights reserved. Drive Z: = Driver TOSCD001 unit 0 TOSHIBA MACHINE Invalid drive specification Path not found - C:\TOOLS\CDROMDRV.SYS Invalid drive specification Invalid drive specification After that last line, it leaves me at a bitmap image displaying instructions to reboot with Ctrl+Alt+Del. It doesn't say why I have to reboot, and it doesn't state any error type, it just want's me to reboot for no apparent reason. After reboot, it just boots up from Floppy again and it cycles through the same thing all over again. The computer has been restored to original specification. Original system recovery "CD-ROM" discs are available and they are not scratched or anything, they are in very good condition. It's a set of 3 CDs, and the first disc labeled "1/3" should be the one holding the OEM version of Windows 98 SE. There is also a boot disk for Windows 98. I'm not sure what the other two discs are for. This computer came with three language support, so those could be holding different language versions or additional OEM discs. But I'm quite sure that the first disc holds the main operating system. BIOS has been set to optimized defaults. Boot priority is as follows; Floppy, IDE-0, CD-ROM. Under Standard CMOS settings, BIOS scans and autoconfigures both the hard drive and the CD/DVD drive. On POST it finds them both, and it finds the DOS bootdisk and starts preparing for installation, as you can see above. So what's this "invalid drive specification" about? Why isn't the installation starting? Updates Update 1 Booting from CD disc 2 In desperation I tried booting from the second CD. Boot order was; Floppy, CD-ROM, IDE-0. It boots normally from floppy disk, just like above, but then returns following. File not found - Z:\3LNGINST\TOOLS\PARTINFO.TXT I accidentally pressed some key on the keyboard, and before I knew it, the following screen showed up. Create Primary DOS Partition Current fixed disk drive: 1 Verifying drive integrity, 16% complete. After completion another screen showed up. Create Primary DOS Partition Current fixed disk drive: 1 Do you wish to use the maximum available size for a Primary DOS Partition and make the partition active (Y/N)?....................? [Y] Verifying drive integrity, 7% complete. I didn't choose Yes, it was set automatically. After completion the computer was automatically rebooted. Then I got a new screen. This is in Norwegian/Swedish/Finnish. Here's the message in Swedish. Hårddisken är inte klar för återställning av programvara. Installationsprogrammet måste skapa nya partitioner (C:, D:, ...). VARNING! ALLT INNEHÅLL PÅ HÅRDDISKEN KOMMER ATT RADERAS! Tryck på en tangent om du vill fortsätta (eller CTRL-C för att avbryta). Let me translate that. Hard drive is not ready for restoring the software. Setup program has to create new partitions (C:, D:, ...). WARNING! ALL CONTENTS ON THE HARD DRIVE WILL BE ERASED! Press any key to continue (or CTRL-C to cancel). I pressed Enter and it started formatting the hard drive. WARNING, ALL DATA ON NON-REMOVABLE DISK DRIVE c: WILL BE LOST! Proceed with Format (Y/N)?y Formatting 14,67.53M 1 percent completed. It automatically sets the "y" option and starts formatting. Rebooting with CD disc 1 After completing this operation it rebooted automatically. I inserted CD disc 1 and there was no issue with "invalid drive specification" anymore. Instead, a bitmap menu was displayed where it asked me to choose a language. And I thought I had it there for a while but it didn't work out. After choosing the language, another menu was displayed asking me to choose a type of recovery (restore pre-installed software OR restore hard drive partitions and pre-installed software). I opted for the second option. Then a data destruction warning showed up where I just pressed 1 to Continue. It did something and then just rebooted and the same formatting screen shows up as before. So something is not right. Am I doing it wrong? I seem to have come past the CD-ROM driver issue at least. But now I'm stuck with this problem... it seems to have something to do with the hard drive. Like... why is is it always trying to format it? Isn't it enough to format it once? By the way, it needs to be formatted as FAT32, right? Windows 98 doesn't support NTFS? I think FDISK should have taken care of this already. I know this is an old hard drive, but I connected to my main computer and it was able to read and write to it without a problem. It does have bad sectors though, but it's expected on an old hard drive like this. Any ideas?.. Update 2 I seem to be repeatedly getting stuck at the format screen where it asks to press any key to continue. So tried to cancel it this time with Ctrl+C. This leaves me at: A:\TOOLS> I can do DIR and CD and I tried to change to Z: drive. I tried running "setup" but there is no such thing. Z:\>setup Bad command or file name Update 3 Floppy structure Here's the file/folder structure of the floppy disk. A:\>dir /s Volume in drive A has no label. Volume Serial Number is 1700-1069 Directory of A:\ 1999-10-11 10:44 <DIR> BMP 1998-05-11 22:01 93 880 COMMAND.COM 1999-10-11 10:44 <DIR> factory 1999-10-11 10:44 <DIR> lang 1999-10-11 10:44 <DIR> TOOLS 2000-05-19 15:32 339 CONFIG.SYS 1999-10-26 13:38 0 BOOTLOG.TXT 2000-06-08 08:32 3 691 AUTOEXEC.BAT 4 File(s) 97 910 bytes Directory of A:\BMP 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 0 File(s) 0 bytes Directory of A:\factory 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 2000-06-08 13:09 2 662 3LNGINSF.BAT 1 File(s) 2 662 bytes Directory of A:\lang 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 1998-11-24 08:02 49 575 FORMAT.COM 1998-11-24 08:02 63 900 FDISK.EXE 2 File(s) 113 475 bytes Directory of A:\TOOLS 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 1998-05-06 22:01 49 575 FORMAT.COM 1995-10-27 20:29 28 164 BMPVIEW.EXE 1999-01-26 15:54 15 MAKEPA32.TXT 1998-05-06 22:01 3 878 XCOPY.EXE 1998-05-06 22:01 41 472 XCOPY32.MOD 1998-05-06 22:01 33 191 HIMEM.SYS 1998-05-06 22:01 125 495 EMM386.EXE 1998-05-06 22:01 18 967 SYS.COM 1996-01-31 21:55 18 CLK.COM 1994-04-02 08:20 22 HARDBOOT.COM 1999-02-03 15:46 15 MAKEPA16.TXT 1999-04-14 16:36 7 840 PARTFO32.EXE 2000-05-19 15:01 1 169 PARTFORM.BAT 1996-10-02 01:47 1 642 MBRCLR.COM 1999-07-01 11:58 8 175 BIOSCHKN.EXE 1998-06-23 08:55 5 904 PAR-TYPE.EXE 1998-11-24 08:02 29 271 MODE.COM 1998-11-24 08:02 15 252 ATTRIB.EXE 1998-11-24 08:02 19 083 DELTREE.EXE 1999-04-21 15:01 23 304 NTBB.EXE 1997-05-07 14:19 1 SYS.TXT 1999-07-01 12:23 61 566 F3DCHK.EXE 1998-05-11 20:01 34 566 KEYBOARD.SYS 1998-05-11 20:01 19 927 KEYB.COM 1999-10-26 14:31 910 partinfo.txt 1998-06-16 15:58 5 936 CHKDRVAC.EXE 1998-05-06 22:01 63 900 FDISK.EXE 1998-05-06 22:01 45 379 SMARTDRV.EXE 1992-12-03 19:48 10 695 SCISET.EXE 1997-06-25 15:49 6 YENT 1998-05-06 22:01 25 473 MSCDEX.EXE 1998-05-06 22:01 5 239 CHOICE.COM 1997-07-18 17:41 6 876 MBR.COM 1997-07-01 15:01 6 545 CHK2GB.COM 1998-06-10 20:04 8 128 PARTFORM.EXE 1990-01-04 02:09 19 MAKEPAR2.TXT 1990-01-04 01:00 27 MAKEPAR3.TXT 1990-01-04 01:00 27 MAKEPAR4.TXT 1998-02-13 13:47 15 MAKEPART.TXT 1999-04-14 13:47 5 200 DISKSIZE.EXE 1999-05-06 14:56 7 856 PARTFO16.EXE 1999-01-13 11:13 13 720 CDROMDRV.SYS 42 File(s) 734 463 bytes Total Files Listed: 49 File(s) 948 510 bytes 12 Dir(s) 268 800 bytes free A:\> CONFIG.SYS contents Here's the content of CONFIG.SYS. DEVICE=A:\TOOLS\HIMEM.SYS /TESTMEM:OFF REM I=B000-B7ff for Desktop BIOSes rem DEVICE=A:\TOOLS\EMM386.EXE NOEMS I=B000-B7ff x=C000-D000 DEVICE=A:\TOOLS\EMM386.EXE NOEMS x=C000-D000 DEVICE=A:\TOOLS\CDROMDRV.SYS /D:TOSCD001 BUFFERS=10 FILES=69 DOS=HIGH,UMB STACKS=9,256 LASTDRIVE=Z SWITCHES=/F SHELL=A:\COMMAND.COM /P /E:2048 AUTOEXEC.BAT contents :BEGIN @ECHO OFF PATH=A:\;A:\TOOLS; MSCDEX /D:TOSCD001 /L:Z /M:10 smartdrv 1024 128 SET TOOLS=A:\TOOLS SET COMSPEC=A:\COMMAND.COM SET EXITDRIVE=C: SET EXITPATH=\ CALL Z:\SETENV.BAT > NUL :TOSHCHK BIOSChkN IF NOT ERRORLEVEL 1 goto C_ACCESS BMPVIEW Z:\3LNGINST\BMP\NO_TOSP3.bmp /X=120 /Y=80 PAUSE > NUL SET EXITDRIVE=A: GOTO END :C_ACCESS CALL PARTFORM.BAT :C_EMPTY IF EXIST C:\*.* GOTO C_NOTEMPTY call z:\setenv.bat>nul goto PREPDU :C_NOTEMPTY REM ------------------MENU------------------------ :STARTMENU CLS BMPVIEW Z:\3LNGINST\BMP\LANGSELC.BMP /X=120 /Y=120 CLK CHOICE /C:123 /N >NUL REM L is the language that is selected IF ERRORLEVEL 1 SET L=%LNG1% IF ERRORLEVEL 2 SET L=%LNG2% IF ERRORLEVEL 3 SET L=%LNG3% SET BMP=BMP%L% BMPVIEW Z:\3LNGINST\%bmp%\HDDMENU.BMP /X=72 /Y=82 CLK CHOICE /C:129F /N > NUL IF ERRORLEVEL 4 GOTO FACTORY_MENU IF ERRORLEVEL 3 GOTO EXIT_MENU IF ERRORLEVEL 2 GOTO PARTFORM_MENU IF ERRORLEVEL 1 GOTO FORMAT_MENU GOTO END :FACTORY_MENU BMPVIEW Z:\3LNGINST\%bmp%\qformat.bmp /X=120 /Y=140 CLK choice /c:12 /N >nul IF ERRORLEVEL 2 GOTO STARTMENU IF ERRORLEVEL 1 GOTO FORMATF GOTO END :EXIT_MENU BMPVIEW Z:\3LNGINST\%bmp%\9.bmp /XC /X=96 /Y=267 choice /C:1pause /T:1,01 >nul SET EXITDRIVE=A: SET EXITPATH=\lang cls mode mono rem keyb xx>nul cls GOTO END :PARTFORM_MENU BMPVIEW Z:\3LNGINST\%bmp%\2.bmp /XC /X=96 /Y=216 choice /C:1pause /T:1,01 >nul BMPVIEW Z:\3LNGINST\%bmp%\partform.bmp /X=120 /Y=140 CLK choice /c:12 /N >nul IF ERRORLEVEL 2 GOTO STARTMENU IF ERRORLEVEL 1 GOTO PART_FORM SET EXITDRIVE=A: GOTO END :FORMAT_MENU BMPVIEW Z:\3LNGINST\%bmp%\1.bmp /XC /X=96 /Y=165 choice /C:1pause /T:1,01 >nul BMPVIEW Z:\3LNGINST\%bmp%\qformat.bmp /X=120 /Y=140 CLK choice /c:12 /N >nul IF ERRORLEVEL 2 GOTO STARTMENU IF ERRORLEVEL 1 GOTO FORMAT SET EXITDRIVE=A: GOTO END REM ------------------ MENU END ------------------------ :FORMAT bmpview Z:\3LNGINST\%bmp%\1.bmp /XC /X=145 /Y=235 choice /C:1pause /T:1,01 >nul CLS IF (%QFORMAT%)==(NO) GOTO FULLFO FORMAT C: /Q /V:"" <A:\TOOLS\YENT >NUL call z:\setenv.bat>nul goto PREPDU :FULLFO FORMAT C: /V:"" <A:\TOOLS\YENT call z:\setenv.bat>nul goto PREPDU :FORMATF CLS IF (%QFORMAT%)==(NO) GOTO FULLFO_F FORMAT C: /Q /V:"" <A:\TOOLS\YENT >NUL call z:\setenv.bat>nul goto PREPDU_F :FULLFO_F FORMAT C: /V:"" <A:\TOOLS\YENT call z:\setenv.bat>nul goto PREPDU_F :PART_FORM bmpview Z:\3LNGINST\bmp\1.bmp /XC /X=145 /Y=235 choice /C:1pause /T:1,01 >nul MBR /! HARDBOOT REM ====================== Triple Select ====================== :PREPDU XCOPY z:\3LNGINST\*.* C:\*.* /E /S /V >NUL ATTRIB -H -R -S C:\TOOLS\CDROMDRV.SYS COPY A:\TOOLS\CDROMDRV.SYS C:\TOOLS /Y SYS C: >NUL goto REBOOT :PREPDU_F copy A:\TOOLS\SMARTDRV.EXE C:\ /Y ATTRIB -H -R -S C:\SMARTDRV.EXE copy A:\FACTORY\3LNGINSF.bat c:\ c:\3LNGINSF.bat cls REM ====================== Dual Select END ====================== REM --------------- END ------------------ :REBOOT SMARTDRV.EXE /C bmpview Z:\3LNGINST\BMP\reboot3.bmp /X=120 /Y=140 :FOREVER pause >nul goto FOREVER :END SMARTDRV.EXE /C %EXITDRIVE% cd %EXITPATH% echo on CD structure S:\>dir /s Volume in drive S is T3ELK4SC Volume Serial Number is 2042-5BC9 Directory of S:\ 2000-08-22 14:14 <DIR> 3LNGINSF 2000-08-22 14:14 <DIR> 3LNGINST 2000-06-15 15:57 <DIR> CRC 2000-06-15 12:04 387 667 767 T310C1NO.W98 2000-09-07 15:36 273 setenv.BAT 2 File(s) 387 668 040 bytes Directory of S:\3LNGINSF 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1999-10-27 10:51 1 806 AUTOEXEC.BAT 2000-08-22 14:14 <DIR> BMP 2000-05-19 15:29 265 CONFIG.SYS 2000-08-22 14:14 <DIR> POSTINST 2000-08-22 14:14 <DIR> TOOLS 2000-08-22 14:14 <DIR> WIN98SYS 2 File(s) 2 071 bytes Directory of S:\3LNGINSF\BMP 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1999-01-04 02:38 718 3.BMP 2000-07-05 11:22 60 118 Cdchg2.bmp 2000-07-05 11:22 60 118 Cdchg3.bmp 2000-07-05 13:37 60 118 Fin.bmp 2000-07-06 14:18 120 118 Menu.bmp 2000-07-05 13:34 60 118 Nor.bmp 2000-07-05 11:53 35 318 Progress.bmp 2000-07-05 13:40 60 118 Swe.bmp 2000-07-05 12:09 84 118 Wrongcd2.bmp 2000-07-05 12:09 84 118 Wrongcd3.bmp 12 File(s) 626 416 bytes Directory of S:\3LNGINSF\POSTINST 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-05-19 09:15 33 POSTINST.BAT 1 File(s) 33 bytes Directory of S:\3LNGINSF\TOOLS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-07-06 14:49 3 593 3LNGINST.BAT 1998-11-24 08:02 15 252 ATTRIB.EXE 1995-10-27 18:29 28 164 BMPVIEW.EXE 1999-01-13 11:13 13 720 CDROMDRV.SYS 1998-05-06 20:01 5 239 CHOICE.COM 1996-01-31 19:55 18 CLK.COM 1998-11-24 08:02 19 083 DELTREE.EXE 1998-05-06 20:01 125 495 EMM386.EXE 1999-07-01 12:23 61 566 F3DCHK.EXE 1998-05-06 20:01 49 575 FORMAT.COM 1994-04-02 06:20 22 HARDBOOT.COM 1998-05-06 20:01 33 191 HIMEM.SYS 1998-05-06 20:01 25 473 MSCDEX.EXE 1998-05-06 20:01 12 663 RAMDRIVE.SYS 1998-05-06 20:01 45 379 SMARTDRV.EXE 1997-05-07 14:19 1 SYS.TXT 1995-09-27 14:25 6 813 VOLCHECK.EXE 1998-05-06 20:01 3 878 XCOPY.EXE 1998-05-06 20:01 41 472 XCOPY32.MOD 1997-06-25 13:49 6 YENT 20 File(s) 490 603 bytes Directory of S:\3LNGINSF\WIN98SYS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1998-12-04 20:00 222 390 IO.SYS 1998-05-06 20:01 18 967 SYS.COM 1998-05-06 20:01 93 880 command.com 3 File(s) 335 237 bytes Directory of S:\3LNGINST 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1999-05-31 09:51 1 576 AUTOEXEC.BAT 2000-08-22 14:14 <DIR> BMP 2000-08-22 14:14 <DIR> Bmpfin 2000-08-22 14:14 <DIR> Bmpnor 2000-08-22 14:14 <DIR> Bmpswe 2000-05-19 15:30 265 CONFIG.SYS 2000-08-22 14:14 <DIR> POSTINST 2000-08-22 14:14 <DIR> TOOLS 2000-08-22 14:14 <DIR> WIN98SYS 2 File(s) 1 841 bytes Directory of S:\3LNGINST\BMP 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1999-01-04 02:38 718 3.BMP 2000-07-05 11:22 60 118 Cdchg2.bmp 2000-07-05 11:22 60 118 Cdchg3.bmp 2000-07-05 13:37 60 118 Fin.bmp 2000-07-06 14:18 120 118 Menu.bmp 2000-07-05 13:34 60 118 Nor.bmp 2000-07-05 11:53 35 318 Progress.bmp 2000-07-06 14:08 40 518 Reboot3.bmp 2000-07-05 13:40 60 118 Swe.bmp 2000-07-05 12:09 84 118 Wrongcd2.bmp 2000-07-05 12:09 84 118 Wrongcd3.bmp 2000-07-05 13:52 48 118 langselc.bmp 2000-07-05 11:47 57 318 no_tosp3.bmp 15 File(s) 772 370 bytes Directory of S:\3LNGINST\Bmpfin 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1998-06-13 00:07 718 9.bmp 2000-03-08 15:02 78 486 Hddmenu.bmp 2000-03-08 15:31 25 318 No_tospc.bmp 2000-03-08 15:37 36 518 PARTFORM.BMP 2000-03-08 15:42 36 518 Qformat.bmp 7 File(s) 178 994 bytes Directory of S:\3LNGINST\Bmpnor 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1998-06-13 00:07 718 9.bmp 1999-05-05 13:26 78 486 Hddmenu.bmp 1998-07-13 11:36 25 318 No_tospc.bmp 1998-07-13 11:41 36 518 PARTFORM.BMP 1998-07-13 11:45 36 518 Qformat.bmp 7 File(s) 178 994 bytes Directory of S:\3LNGINST\Bmpswe 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1998-06-13 00:07 718 9.bmp 1999-05-06 08:14 78 486 Hddmenu.bmp 1998-07-10 16:25 25 318 No_tospc.bmp 1998-07-10 16:29 36 518 PARTFORM.BMP 1998-07-10 17:08 36 518 Qformat.bmp 7 File(s) 178 994 bytes Directory of S:\3LNGINST\POSTINST 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-05-19 09:15 33 POSTINST.BAT 1 File(s) 33 bytes Directory of S:\3LNGINST\TOOLS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-05-19 14:52 3 898 3LNGINST.BAT 1995-10-27 18:29 28 164 BMPVIEW.EXE 1999-01-13 11:13 13 720 CDROMDRV.SYS 1998-05-06 20:01 5 239 CHOICE.COM 1996-01-31 19:55 18 CLK.COM 1998-05-06 20:01 125 495 EMM386.EXE 1999-07-01 12:23 61 566 F3DCHK.EXE 1998-05-06 20:01 49 575 FORMAT.COM 1994-04-02 06:20 22 HARDBOOT.COM 1998-05-06 20:01 33 191 HIMEM.SYS 1998-05-06 20:01 25 473 MSCDEX.EXE 2000-07-06 14:41 910 PARTINFO.TXT 1998-05-06 20:01 12 663 RAMDRIVE.SYS 1998-05-06 20:01 45 379 SMARTDRV.EXE 1997-05-07 14:19 1 SYS.TXT 1995-09-27 14:25 6 813 VOLCHECK.EXE 1998-05-06 20:01 3 878 XCOPY.EXE 1998-05-06 20:01 41 472 XCOPY32.MOD 1997-06-25 13:49 6 YENT 19 File(s) 457 483 bytes Directory of S:\3LNGINST\WIN98SYS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1998-12-04 20:00 222 390 IO.SYS 1998-05-06 20:01 18 967 SYS.COM 1998-05-06 20:01 93 880 command.com 3 File(s) 335 237 bytes Directory of S:\CRC 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-06-15 12:07 181 422 T310C1NO.ALL 2000-06-15 12:09 215 427 T310C1NO.CRC 2000-06-15 12:07 2 157 T310C1NO.HID 3 File(s) 399 006 bytes Total Files Listed: 104 File(s) 391 625 352 bytes 42 Dir(s) 0 bytes free S:\> Now which line or lines need to be changed? Do I really have to change drive letter Z: to C:? Proposed solutions Solution #1 Ramhound proposed to change the boot order to following; CD-ROM, IDE-0, Floppy This didn't help. In fact, here is the result of it. Searching for Boot Record from CDROM..Not Found Searching for Boot Record from IDE-0.. OK Missing operating system Any other ideas?... Solution #2 Rik proposed to run Z:\setup. Now that I have found a way to drop to DOS prompt with Ctrl+C as described above (Update 2), I did try running setup but there is no such command or file in there. So that didn't work.

  Read the article

• Sending text messages from Raspberry Pi via email fails

  - by vgm64

  I'm using mailx on my raspberry pi to try to send text messages updates for event monitoring. My phone number: 9876543210 My phone's email-to-text gateway address: [email protected] I can 1) Send emails from my raspberry pi to various email addresses. mail -r [email protected] -s "My Subject" [email protected] < body.txt and off it goes and is successfully delivered. 2) Send emails from various email address (not on RPi) using mailx to the above phone-email address and have them delivered as text messages. However, when sending emails to [email protected] from the Raspberry Pi using mailx the emails seem to spiral into the void and are never heard of again (no errors, no undeliverable messages, nothing). Does anyone know what could be causing this to go awry? Something about the basic deployment of the mail server on the pi? EDIT Based on @kobaltz's suggestion, I used sendmail instead. This led to a hang, then an error that stated that I lacked a fully qualified domain name (FQDN). I then used this website's instructions to add a domain name to the RPi. To paraphrase: I have set the FQDN in /etc/hostname: my-host-name.my-domain.com and /etc/hosts: 127.0.0.1 localhost.localdomain localhost 192.168.0.5 my-host-name.my-domain.com my-host-name Then add to /etc/mail/sendmail.cf: MASQUERADE_AS(`my-domain.com') MASQUERADE_DOMAIN(`my-host-name.my-domain.com') FEATURE(`masquerade_entire_domain') FEATURE(`masquerade_envelope') I put this in /etc/mail/sendmail.cf, BEFORE the MAILER() lines, ran sendmailconfig, answered Yes to the questions about using the existing files, and restarted sendmail. Emails now have the proper domain name. Progress, however, I am now stuck at the following error: 354 Enter mail, end with "." on a line by itself >>> . 050 <[email protected]>... Connecting to mxx.cingularme.com. via esmtp... 050 421 Service not available 050 >>> QUIT 050 <[email protected]>... Deferred: 421 Service not available 250 2.0.0 q9U3ZESt021150 Message accepted for delivery [email protected]... Sent (q9U3ZESt021150 Message accepted for delivery) Closing connection to [127.0.0.1] >>> QUIT

  Read the article

• Veewee, Vagrant, Puppet, Erlang and RabbitMQ

  - by Tobias

  I am kinda stuck with a problem I am trying to wrap my head around for days now. Here is what I am doing: By using Veewee, I am creating a VirtualBox image and then I create a Vagrant box from it. See here, here Finally I run puppet from Vagrant to install RabbitMQ, see here. Veewee, Vagrant and VirtualBox all run on MacOS X 10.7.4. The vagrant box itself is CentOS 6.2. This worked fine for quite some time until I was recreating the VirtualBox image a couple of days ago. During installation of the rabbitmq-plugins during my puppet run I now get the following error: /Stage[main]/Rabbitmq/Exec[rabbitmq-plugins]/returns: erlexec: HOME must be set My RabbitMQ puppet configuration can be found on my GitHub repo for that project, but here is the most important part: $version = "2.8.7" $url = "http://www.rabbitmq.com/releases/rabbitmq-server/v${version}/rabbitmq-server-${version}-1.noarch.rpm" package{"erlang": ensure => "present", } package{"rabbitmq-server": provider => "rpm", source => $url, require => Package["erlang"] } exec{"rabbitmq-plugins": path => "/usr/bin:/usr/sbin:/bin", command => "rabbitmq-plugins enable rabbitmq_management", require => Package["rabbitmq-server"] } My additional repositories, e.g. epel, are defined in veewees postinstall.sh right at the top of the file. Finally, this is what I get when I do '/etc/init.d/rabbitmq-server status' [{pid,2834}, {running_applications,[{rabbit,"RabbitMQ","2.8.7"}, {ssl,"Erlang/OTP SSL application","4.1.6"}, {public_key,"Public key infrastructure","0.13"}, {crypto,"CRYPTO version 2","2.0.4"}, {mnesia,"MNESIA CXC 138 12","4.5"}, {os_mon,"CPO CXC 138 46","2.2.7"}, {sasl,"SASL CXC 138 11","2.1.10"}, {stdlib,"ERTS CXC 138 10","1.17.5"}, {kernel,"ERTS CXC 138 10","2.14.5"}]}, {os,{unix,linux}}, {erlang_version,"Erlang R14B04 (erts-5.8.5) [source] [64-bit] [rq:1] [async-threads:30] [kernel-poll:true]\n"}, {memory,[{total,24993120}, {processes,10328496}, {processes_used,10321296}, {system,14664624}, {atom,1175905}, {atom_used,1143841}, {binary,17192}, {code,11416020}, {ets,766168}]}, {vm_memory_high_watermark,0.4}, {vm_memory_limit,205851852}, {disk_free_limit,1000000000}, {disk_free,7089795072}, {file_descriptors,[{total_limit,924}, {total_used,4}, {sockets_limit,829}, {sockets_used,2}]}, {processes,[{limit,1048576},{used,131}]}, {run_queue,0}, {uptime,6}] Sources in the web suggest, that I have to set HOME. Of course I was logging into the box if HOME was set, for user vagrant it was '/home/vagrant' and for root it was 'root'. As always, any hints/ideas/suggestions/assumptions are more than welcome. Thanks a lot! Cheers, Tobi

  Read the article

• Error codes 80070490 and 8024200D in Windows Update

  - by Sammy

  How do get past these stupid errors? The way I have set things up is that Windows Update tells me when there are new updates available and then I review them before installing them. Yesterday it told me that there were 11 new updates. So I reviewed them and I saw that about half of them were security updates for Vista x64 and .NET Framework 2.0 SP2, and half of them were just regular updates for Vista x64. I checked them all and hit the Install button. It seemed to work at first, updates were being downloaded and installed, but then at update 11 of 11 total it got stuck and gave me the two error codes you see in the title. Here are some screenshots to give you an idea of what it looks like. This is what it looks like when it presents the updates to me. This is how it looks like when the installation fails. I'm not sure if you're gonna see this very well but these are the updates it's trying to install. Update: This is on Windows Vista Ultimate 64-bit with integrated SP2, installed only two weeks ago on 2012-10-02. Aside from this, the install is working flawlessly. I have not done any major changes to the system like installing new devices or drivers. What I have tried so far: - I tried installing the System Update Readiness Tool (the correct one for Vista x64) from Microsoft. This did not solve the issue. Microsoft resource links: Solutions to 80070490 Windows Update error 80070490 System Update Readiness Tool fixes Windows Update errors in Windows 7, Windows Vista, Windows Server 2008 R2, and Windows Server 2008 Solutions to 8024200D: Windows Update error 8024200d Essentially both solutions tell you to install the System Update Readiness Tool for your system. As I have done so and it didn't solve the problem the next step would be to try to repair Windows. Before I do that, is there anything else I can try? Microsoft automatic troubleshooter If I click the automatic troubleshooter link available on the solution web page above it directs me to download a file called windowsupdate.diagcab. But after download this file is not associated to any Windows program. Is this the so called Microsoft Fix It program? It doesn't have its icon, it's just blank file. Does it need to be associated? And to what Windows program?

  Read the article

• ActiveMQ Pure Master / Slave - Out of sync

  - by pico

  What i have : 1 master broker and 1 slave broker both in ActiveMQ 5.4.0 What i use : waitForSlave on master side and failover uri on slave side (in the master connector URI) What i want to do : I want to wait some delay (like 5 seconds) in case of a tiny network failures between master and slave before starting slave transpôrt connectors So i put this in slave config : <broker xmlns="http://activemq.apache.org/schema/core" brokerName="slave" dataDirectory="${activemq.base}/data" useJmx="true" persistent="true" populateJMSXUserID="true" masterConnectorURI="failover://(tcp://master:61616)?initialReconnectDelay=1000&amp;maxReconnectDelay=30000" shutdownOnMasterFailure="false" advisorySupport="false"> It seems to work but after a network hang between master and slave, the slave reconnect successfully and then the master logs a lot of : 2010-10-18 17:08:44,421 | ERROR | Slave Failed | org.apache.activemq.broker.ft.MasterBroker | ActiveMQ Task java.lang.IllegalStateException: Cannot lookup a connection that had not been registered: ID:master-1040-634226732611718750-0:0 at org.apache.activemq.broker.MapTransportConnectionStateRegister.lookupConnectionState(MapTransportConnectionStateRegister.java:93) at org.apache.activemq.broker.TransportConnection.lookupConnectionState(TransportConnection.java:1412) at org.apache.activemq.broker.TransportConnection.processRemoveConsumer(TransportConnection.java:561) at org.apache.activemq.command.RemoveInfo.visit(RemoveInfo.java:76) at org.apache.activemq.broker.TransportConnection.service(TransportConnection.java:309) at org.apache.activemq.broker.TransportConnection$1.onCommand(TransportConnection.java:185) at org.apache.activemq.transport.ResponseCorrelator.onCommand(ResponseCorrelator.java:116) at org.apache.activemq.transport.TransportFilter.onCommand(TransportFilter.java:69) at org.apache.activemq.transport.vm.VMTransport.iterate(VMTransport.java:218) at org.apache.activemq.thread.DedicatedTaskRunner.runTask(DedicatedTaskRunner.java:98) at org.apache.activemq.thread.DedicatedTaskRunner$1.run(DedicatedTaskRunner.java:36) On the slave side everything is fine. So after that, i've tried to stop the master to see if the slave is capable of turning master after these "network hangs". The master took long time to shutdown (10 seconds) and then some error message appears in slave logs : 2010-10-18 17:09:32,915 | WARN | Async error occurred: java.lang.IllegalStateException: Cannot lookup a connection that had not been registered: ID:master-1049-634226732657812500-0:3 | org.apache.activemq.broker.TransportConnection.Service | VMTransport: vm://slave#5 java.lang.IllegalStateException: Cannot lookup a connection that had not been registered: ID:master-1049-634226732657812500-0:3 at org.apache.activemq.broker.MapTransportConnectionStateRegister.lookupConnectionState(MapTransportConnectionStateRegister.java:93) at org.apache.activemq.broker.TransportConnection.lookupConnectionState(TransportConnection.java:1412) at org.apache.activemq.broker.TransportConnection.processRemoveSession(TransportConnection.java:600) at org.apache.activemq.command.RemoveInfo.visit(RemoveInfo.java:74) at org.apache.activemq.broker.TransportConnection.service(TransportConnection.java:309) at org.apache.activemq.broker.TransportConnection$1.onCommand(TransportConnection.java:185) at org.apache.activemq.transport.ResponseCorrelator.onCommand(ResponseCorrelator.java:116) at org.apache.activemq.transport.TransportFilter.onCommand(TransportFilter.java:69) at org.apache.activemq.transport.vm.VMTransport.iterate(VMTransport.java:218) at org.apache.activemq.thread.DedicatedTaskRunner.runTask(DedicatedTaskRunner.java:98) at org.apache.activemq.thread.DedicatedTaskRunner$1.run(DedicatedTaskRunner.java:36) Are they any ways to keep my kaha stores (they are individual stores) synchronised? The main problem is that the slave never turn master after a master failure, it stay block on this message : 2010-10-18 17:09:33,681 | WARN | Transport (master/172.21.60.61:61616) failed to tcp://master:61616 , attempting to automatically reconnect due to: java.net.SocketException: Software caused connection abort: socket write error | org.apache.activemq.transport.failover.FailoverTransport | ActiveMQ Transport: tcp://master/172.21.60.61:61616 I'm totally stuck with these syncs problems, any help welcome! Regards

  Read the article

• Connectivity issues with dual NIC machine in EC2

  - by Matt Sieker

  I'm trying to get some servers set up in EC2 in a Virtual Private Cloud. To do this, I have two subnets: 10.0.42.0/24 - Public subnet 10.0.83.0/24 - Private subnet To bridge these two, I have a Funtoo instance with a pair of NICs: eth0 10.0.42.10 eth1 10.0.83.10 Which has the following routing table: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.83.0 * 255.255.255.0 U 0 0 0 eth1 10.0.83.0 * 255.255.255.0 U 203 0 0 eth1 10.0.42.0 * 255.255.255.0 U 202 0 0 eth0 loopback * 255.0.0.0 U 0 0 0 lo default 10.0.42.1 0.0.0.0 UG 0 0 0 eth0 default 10.0.42.1 0.0.0.0 UG 202 0 0 eth0 An elastic IP is attached to the eth0 interface, and I can connect to it fine remotely. However, I cannot ping anything in the 10.0.83.0 subnet. For now iptables is not set up on the box, so there's no rules that would get in the way (Eventually this will be managed by Shorewall, but I should get basic connectivity done first) Subnet details from the VPC interface: CIDR: 10.0.83.0/24 Destination Target 10.0.0.0/16 local 0.0.0.0/0 [ID of eth1 on NAT box] Network ACL: Default Inbound: Rule # Port (Service) Protocol Source Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY Outbound: Rule # Port (Service) Protocol Destination Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY   CIDR: 10.0.83.0/24 VPC: Destination Target 10.0.0.0/16 local 0.0.0.0/0 [Internet Gateway ID] Network ACL: Default (replace) Inbound: Rule # Port (Service) Protocol Source Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY Outbound: Rule # Port (Service) Protocol Destination Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY I've been trying to work this out most of the evening, but I'm just stuck. I'm either missing something obvious, or am doing something very wrong. I would think I'd be able to ping from either interface on this box without issue. Hopefully some more pairs of eyes on this configuration will help. EDIT: I am an idiot. After I bothered to install nmap to run some more tests, I discover I can see the ports, and connect to them, pings are just being blocked.

  Read the article

• LaunchDaemon causing Lion to hang on boot

  - by Brett

  I've got a Mac Mini 2011, which I intend to use for a few tasks such as Plex and running a few VM's. I've installed virtualbox, along with XAMPP and phpvirtualbox, which all worked fine. However, getting this to run on startup is proving a real PITA! I'm at the moment trying to get vboxwebsrv running on boot. I've created a launchd plist within /Library/LaunchDaemons to run it and it works fine... well sort of. Lion when booting will show the spinning wheel and stop, never showing a GUI - however if I remote in via screen sharing or SSH, I can login fine and see that vboxwebsrv has launched successfully. Setting this plist to disabled makes lion boot up fine again. Initially I thought it was due to it staying open, so tried to add -b which causes it to run in the background, this just caused launchd to constantly spawn new processes and didn't even fix my problem of Lion being stuck at the spinning wheel. Does anyone have any ideas? I'm losing my mind here! PLIST: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>Disabled</key> <false/> <key>KeepAlive</key> <false/> <key>UserName</key> <string>vbox</string> <key>RunAtLoad</key> <true/> <key>OnDemand</key> <false/> <key>Label</key> <string>org.virtualbox.vboxwebsvc</string> <key>ProgramArguments</key> <array> <string>/Applications/VirtualBox.app/Contents/MacOS/vboxwebsrv</string> </array> </dict> </plist>

  Read the article

• Cannot run a VM with more than three network interfaces with KVM

  - by Bostonvaulter

  I'm running KVM on top of Ubuntu 10.10 Server I can create VM's (Virtual Machine) and network interfaces fine but I cannot seem to add more than three network interfaces. As soon as I have a VM with four network interfaces it gets stuck on startup at the starting SeaBIOS page with this message: Starting SeaBIOS (version pre-0.6.1-20100702_143500-palmer) So far I've verified this with two VM's, a Ubuntu 10.10 desktop and a Vyatta router. The specific network hardware I assign to the VM's doesn't seem to matter. I'm trying to have one bridged interface and three private networks using Vyatta to route between them. Does anyone know why I can't run a VM with more than three network interfaces? Edit: Additionally the KVM thread responsible for the specific VM hangs using ~100% CPU (i.e. one core). Here's the command for the process that is hanging: /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 512 -smp 1,sockets=1,cores=1,threads=1 -name vyatta -uuid 6dff7c94-6810-423e-5fea-fec10da0e9b7 -nodefaults -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/vyatta.monitor,server,nowait -mon chardev=monitor,mode=readline -rtc base=utc -boot c -drive file=/home/rams/virtual-machines/vyatta.img,if=none,id=drive-ide0-0-0,boot=on,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -device rtl8139,vlan=0,id=net0,mac=00:54:00:be:cc:4b,bus=pci.0,addr=0x3 -net tap,fd=97,vlan=0,name=hostnet0 -device rtl8139,vlan=1,id=net1,mac=52:54:00:da:59:ed,bus=pci.0,addr=0x5 -net tap,fd=98,vlan=1,name=hostnet1 -device rtl8139,vlan=2,id=net2,mac=52:54:00:ce:22:b6,bus=pci.0,addr=0x6 -net tap,fd=99,vlan=2,name=hostnet2 -device rtl8139,vlan=3,id=net3,mac=52:54:00:1e:bc:46,bus=pci.0,addr=0x7 -net tap,fd=101,vlan=3,name=hostnet3 -chardev pty,id=serial0 -device isa-serial,chardev=serial0 -usb -vnc 127.0.0.1:0 -k en-us -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 Edit: I've also found an error in dmesg that might be related (it also shows up when running virtd in verbose mode): 14:47:24.399: warning : qemudParsePCIDeviceStrs:1422 : Unexpected exit status '1', qemu probably failed I've also tried disabling app armor but that doesn't seem to make a difference.

  Read the article

• Setting Timeouts: SQL Server 2008/IIS 7.5

  - by Julie

  We have recently migrated from a Win 2003/SQL Server 2000 system to Win 2008 64 bit R2, SQL Server 2008 R2. Our websites are in classic asp, and this can't be changed to another scripting language at this time. On the old server, if I got stuck in some kind of endless loop, the page would throw an error. On the new server, I have a page that has some sort of looping problem, that even though the SQL SP is called only once (and runs fine run as a query on the server) it pegs SQL server and therefore locks all of our websites. I'll get my code figured out, no biggie. But I need to make sure the server times out when this happens. (The page I'm working on runs fine with certain instances of the query, and locks with others using a different query variable. I can't have something like that sneak up on me on a page I haven't touched for three years.) I can't figure out how an SP that runs once on the server, from an ASP page, is tying up SQL server this way. It's obviously some sort of a timeout issue, but I can't figure out where/which timeout values to change. I actually have to remote desktop to the server and kill the process in SQL server. I'm afraid I'm a generalist, and server management is not my thing, even though it's my responsibility, so I am almost certain to have questions about any answer that I receive. How can I track this down? What settings do I need to change? More info: It's not SQL Server On our test site, I created an ASP file that just did an endless loop (do while 1=1) and had the same problem - the other websites wouldn't load - without SQL server being involved. So I think the reason the process was hanging is that the page wasn't timing out as it should, and so the connection to SQL was never closed. Killing the process in SQL server would reset the page somehow. For my intentional endless loop, I had to refresh the app pool to get rid of it. This points more to either IIS or the ASP settings. The ASP timeouts are set to whatever the default were when the server was first loaded. I still can't figure out why one file is locking up all websites, though. Again, that didn't happen on the old server.

  Read the article

• Triple monitor setup in linux

  - by Brendan Abel

  I'm hoping there are some xorg gurus out there. I'm trying to get a three monitor setup working in linux. I have 2 lcd monitors and a tv, all different resolutions. I'm using 2 video cards; a 9800 GTX and 7900Gt. I've seen a lot of different posts about people trying to make this work, and in every case, they either gave up, or Xinerama magically solved all their problems. Basically, my main problem is that I cannot get Xinerama to work. Every time I turn it on in the options, my machine gets stuck in a neverending boot cycle. If I disable Xinerama, I just have three Xorg screens, but I can't drag windows from one to the other. I can get the 2 lcds on Twinview, and the tv on a separate Xorg screen no problem. But I don't really like this solution. I'd rather have them all on separate screens and stitch them together with Xinerama. Has anyone done this? Here's my xorg.conf for reference. p.s. This took me all of 30 seconds to set up in Windows XP! p.s.s. I've seen somewhere that maybe randr can solve my problems? But I'm not quite sure how? Section "Monitor" Identifier "Main1" VendorName "Acer" ModelName "H233H" HorizSync 40-70 VertRefresh 60 Option "dpms" EndSection #Section "Monitor" # Identifier "Main2" # VendorName "Acer" # ModelName "AL2216W" # HorizSync 40-70 # VertRefresh 60 # Option "dpms" #EndSection Section "Monitor" Identifier "Projector" VendorName "BenQ" ModelName "W500" HorizSync 44.955-45 VertRefresh 59.94-60 Option "dpms" EndSection Section "Device" Identifier "Card1" Driver "nvidia" VendorName "nvidia" BusID "PCI:5:0:0" BoardName "nVidia Corporation G92 [GeForce 9800 GTX+]" Option "ConnectedMonitor" "DFP,DFP" Option "NvAGP" "0" Option "NoLogo" "True" #Option "TVStandard" "HD720p" EndSection Section "Device" Identifier "Card2" Driver "nvidia" VendorName "nvidia" BusID "PCI:4:0:0" BoardName "nVidia Corporation G71 [GeForce 7900 GT/GTO]" Option "NvAGP" "0" Option "NoLogo" "True" Option "TVStandard" "HD720p" EndSection Section "Module" Load "glx" EndSection Section "Screen" Identifier "ScreenMain-0" Device "Card1-0" Monitor "Main1" DefaultDepth 24 Option "Twinview" Option "TwinViewOrientation" "RightOf" Option "MetaModes" "DFP-0: 1920x1080; DFP-1: 1680x1050" Option "HorizSync" "DFP-0: 40-70; DFP-1: 40-70" Option "VertRefresh" "DFP-0: 60; DFP-1: 60" #SubSection "Display" # Depth 24 # Virtual 4880 1080 #EndSubSection EndSection Section "Screen" Identifier "ScreenProjector" Device "Card2" Monitor "Projector" DefaultDepth 24 Option "MetaModes" "TV-0: 1280x720" Option "HorizSync" "TV-0: 44.955-45" Option "VertRefresh" "TV-0: 59.94-60" EndSection Section "ServerLayout" Identifier "BothTwinView" Screen "ScreenMain-0" Screen "ScreenProjector" LeftOf "ScreenMain-0" #Option "Xinerama" "on" # most important option let you window expand to three monitors EndSection

  Read the article

• Layer 3 switch routing

  - by Yoshiwaan

  I need help moving over to using our layer 3 switch as the inter vlan routing device rather than our cisco router. I've mostly got it working but I've got stuck near the end and need some advice (I think I just need a bit of education on the subject really). Cur I have a Dell PowerConnect 7048 connecting to a Cisco 1841 router. I've got a few key excerpts from the configs to provide the key information. On the powerconnect I have the following: ip routing ip default-gateway 172.31.14.1 ip route 0.0.0.0 0.0.0.0 172.31.14.1 253 ! interface vlan 1 ip address 172.31.14.254 255.255.255.0 exit interface vlan 2 ip address 172.31.19.254 255.255.255.0 exit interface vlan 4 ip address 172.31.16.254 255.255.255.0 ! interface Gi1/0/1 description 'Link to L7Router01' switchport mode trunk switchport trunk allowed vlan except 3,7-4093 exit ! and on the Cisco the following: interface FastEthernet0/0 ip address 172.31.14.1 255.255.255.0 ip nat inside ip virtual-reassembly ! interface FastEthernet0/0.2 description Accounts VLAN encapsulation dot1Q 2 ip address 172.31.19.1 255.255.255.0 ip nat inside ip virtual-reassembly ! interface FastEthernet0/0.4 description Voice VLAN encapsulation dot1Q 4 ip address 172.31.16.1 255.255.255.0 ip nat inside ip virtual-reassembly ! So what I'm doing is moving clients over so that their default gateway is a 172.31.x.254 address rather than a 172.31.x.1 address. This works great for inter-vlan routing, I have no issues with this. The switch can also access the router no worries, and users on the 172.31.14.0/24 network can access all interfaces and sub-interfaces on the router, including 172.31.14.1. They can also access all of the interfaces that the router connects off to, no worries there. The problem I have is that users on the 172.31.16.0/24 and 172.31.19.0/24 subnets cannot access either 172.31.14.1 or any of the subnets the router connects to. They can, however, connect to BOTH of the sub interfaces on the router from either subnet. What am I missing here? Why can't the vlans connect to the non-sub interface on the router? Are tagged packets being sent to this interface?

  Read the article

• OCZ Vertex 2 not recognized by Ubuntu installer

  - by Zsub

  As I boot into the Ubuntu 10.10 (or 11.04, doesn't matter) live environment or installer, it just refuses to recognise my Vertex 2. It reports the disk as ATA and not supporting smart, shows no serial number, and doesn't list the size correctly. All fdisk tells me is Unable to read /dev/sda (it's the only storage in the PC). I'm now running a temporary install of Windows 7 off of it, which worked like a charm, so where am I going wrong with Ubuntu... Specs: Asus M4N68T-M LE V2 (BIOS 0702, most recent) OCZ Vertex 2 SSD 60 GB Amd Athlon II X4 640 Patriot PSD34G13332 4GB DDR3 ram (two banks) EDIT I installed a second drive, installed Ubuntu on that and booted, it recognised the SSD just fine. I'm now trying to apt-get upgrade the live-environment. I wonder if there is any way to sort of install Ubuntu from Ubuntu (I boot into the working install on the other drive, install it on the SSD and then boot from the SSD). EDIT2 Ok, so that doesn't work. The install detects the SSD, however, it cannot format it. EDIT3 After a fresh boot I can read out SMART-data and even perform a read-benchmark, but if I try to format it, or do a write-bench, it'll crap out and after that it says SMART is not supported. So basically it seems I can't write to the disk, as it will stop working when I do, I will try to run repeated read-benchmarks to see if that has any effect. EDIT4 I'm running several read benchmarks on the drive right now, they give results that are to be expected from an SSD. If the read-benches don't fail, I can use fdisk on the disk, but it is now stuck trying to re-read the partition table after issueing the 'w' command. EDIT5 Parted Magic did recognize the drive and with hdparm -I even could tell me the drive was in a frozen state. I powercycled it (just pull out the plug from the SSD and plug it back in) and it wasn't frozen anymore. After that I could upgrade the firmware on the drive (still using Parted Magic) and format it to Ext4. After I rebooted into the Ubuntu installer, it wouldn't get recognized and hdparm didn't want to talk to it saying HDIO_DRIVE_CMD(identify) failed: Invalid exchange. EDIT6 For some reason if I enable one of the RAID controllers (the one the SSD is connected to, obviously) Ubuntu will let me format it, mount it and write to it. The installer also recognizes it. However if the raid controller is enabled but no array is defined the motherboard can't boot from it :(

  Read the article

• Django + gunicorn + virtualenv + Supervisord issue

  - by Florian Le Goff

  Dear all, I have a strange issue with my virtualenv + gunicorn setup, only when gunicorn is launched via supervisord. I do realize that it may very well be an issue with my supervisord and I would appreciate any feedback on a better place to ask for help... In a nutshell : when I run gunicorn from my user shell, inside my virtualenv, everything is working flawlessly. I'm able to access all the views of my Django project. When gunicorn is launched by supervisord at the system startup, everything is OK. But, if I have to kill the gunicorn_django processes, or if I perform a supervisord restart, once that gunicorn_django has relaunched, every request is answered with a weird Traceback : (...) File "/home/hc/prod/venv/lib/python2.6/site-packages/Django-1.2.5-py2.6.egg/django/db/__init__.py", line 77, in connection = connections[DEFAULT_DB_ALIAS] File "/home/hc/prod/venv/lib/python2.6/site-packages/Django-1.2.5-py2.6.egg/django/db/utils.py", line 92, in __getitem__ backend = load_backend(db['ENGINE']) File "/home/hc/prod/venv/lib/python2.6/site-packages/Django-1.2.5-py2.6.egg/django/db/utils.py", line 50, in load_backend raise ImproperlyConfigured(error_msg) TemplateSyntaxError: Caught ImproperlyConfigured while rendering: 'django.db.backends.postgresql_psycopg2' isn't an available database backend. Try using django.db.backends.XXX, where XXX is one of: 'dummy', 'mysql', 'oracle', 'postgresql', 'postgresql_psycopg2', 'sqlite3' Error was: cannot import name utils Full stack available here : http://pastebin.com/BJ5tNQ2N I'm running... Ubuntu/maverick (up-to-date) Python = 2.6.6 virtualenv = 1.5.1 gunicorn = 0.12.0 Django = 1.2.5 psycopg2 = '2.4-beta2 (dt dec pq3 ext)' gunicorn configuration : backlog = 2048 bind = "127.0.0.1:8000" pidfile = "/tmp/gunicorn-hc.pid" daemon = True debug = True workers = 3 logfile = "/home/hc/prod/log/gunicorn.log" loglevel = "info" supervisord configuration : [program:gunicorn] directory=/home/hc/prod/hc command=/home/hc/prod/venv/bin/gunicorn_django -c /home/hc/prod/hc/gunicorn.conf.py user=hc umask=022 autostart=True autorestart=True redirect_stderr=True Any advice ? I've been stuck on this one for quite a while. It seems like some weird memory limit, as I'm not enforcing anything special : $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 20 file size (blocks, -f) unlimited pending signals (-i) 16382 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) unlimited virtual memory (kbytes, -v) unlimited file locks (-x) unlimited Thank you.

  Read the article

• DPM 2010 "Disk failed or disk not found"

  - by SysAdmin

  I have an HP Proliant ML110 G5 server with Windows server 2008R2 only dedicated for DPM 2010. This server has a limit in HD of 8TB which has already been met. I'm now stuck in this situation where my disk keeps failing "Disk failed or Disk not found" in the disk management. Only after I reboot the system the disk comes back up. Today I was running my monthly tape backup on a certain protection group and the disk failed again while the tape job was running (so the job wasn't completed). This is the description of the error in the alerts: "The disk Disk 1 - Hitachi HDS722020ALA330 SCSI Disk Device cannot be detected or has stopped responding. All subsequent protection activities that use this disk will fail until the disk is brought back online. (ID 3120)". My backup system is becoming useless! I don't think that is a hardware issue (please correct me if I'm wrong) since the HD works fine for a certain period of time which is becoming shorter and shorter. I basically have no more option to fix this problem. I tried to fix any error that was coming up in the event viewer with no luck (included one regarding the SQL2008 compatibility issue). The disk keeps failing! Now I'm only trying to recover/migrate the data from the disk that is having problem but my issue now is that I cannot add any drives to my server since I already got installed the maximum storage capacity 8TB. I thought about 2 simple options. Please tell me what you guys think about it; Unplug one of the 2 storage pool disks (disk0, that one without problem) from the machine and install a new one in order to migrate the data with the Migration tool for DPM. Remove the defective disk (disk1), put back the disk0 and run the synchronization/consistency check on all the groups to recreate replicas and recovery points. Run diskpart.exe and clean up the disk (loosing all data) and hoping that he will work after I sync all the protection groups. Both solutions are not elegant but I have no better options at the moment. Please I need some help. Thanks for your time Angelo

  Read the article

• DB2 Integrity Checks and Exception Tables

  - by imthefirestartr

  I am working on planning a migration of a DB2 8.1 database from a horrible IBM encoding to UTF-8 to support further languages etc. I am encountering an issue that I am stuck on. A few notes on this migration: We are using db2move to export and load the data and db2look to get the details fo the database (tablespaces, tables, keys etc). We found the loading process worked nicely with db2move import, however, the data takes 7 hours to load and this was unacceptable downtime when we actually complete the conversion on the main database. We are now using db2move load, which is much faster as it seems to simply throw the data in without integrity checks. Which leads to my current issue. After completing the db2move load process, several tables are in a check pending state and require integrity checks. Integrity checks are done via the following: set integrity for . immediate checked This works for most tables, however, some tables give an error: DB21034E The command was processed as an SQL statement because it was not a valid Command Line Processor command. During SQL processing it returned: SQL3603N Check data processing through the SET INTEGRITY statement has found integrity violation involving a constraint with name "blah.SQL120124110232400". SQLSTATE=23514 The internets tell me that the solution to this issue is to create an exception table based on the actual table and tell the SET INTEGRITY command to send any exceptions to that table (as below): db2 create table blah_EXCEPTION like blah db2 SET INTEGRITY FOR blah IMMEDIATE CHECKED FOR EXCEPTION IN blah USE blah_EXCEPTION NOW, here is the specific issue I am having! The above forces all the rows with issues to the specified exception table. Well that's just super, buuuuuut I can not lose data in this conversion, its simply unacceptable. The internets and IBM has a vague description of sending the violations to the exception tables and then "dealing with the data" that is in the exception table. Unfortunately, I am not clear what this means and I was hoping that some wise individual knows and could help me out and let me know how I can retrieve this data from these tables and place the data in the original/proper table rather than these exception tables. Let me know if you have any questions. Thanks!

  Read the article

• Clonezilla restore from Samba - no 'restoredisk' option

  - by MT_Head

  I used a CloneZilla LiveCD to back up a couple of Windows machines to a Samba share. Now I'm trying to restore those images, and CloneZilla won't even give me the 'restoredisk' or 'restorepart' options on the menu. I'm guessing that this is because CZ isn't recognizing a valid image... but why? Here's a listing of the folder on the Samba share: -rwxrwxrwx 1 marc users 319 May 31 03:45 blkdev.list -rwxrwxrwx 1 marc users 5307 May 31 04:41 clonezilla-img -rwxrwxrwx 1 marc users 4 May 31 04:31 disk -rwxrwxrwx 1 marc users 16091 May 31 04:31 Info-dmi.txt -rwxrwxrwx 1 marc users 11029 May 31 04:31 Info-lshw.txt -rwxrwxrwx 1 marc users 1502 May 31 04:31 Info-lspci.txt -rwxrwxrwx 1 marc users 170 May 31 04:31 Info-packages.txt -rwxrwxrwx 1 marc users 80 May 31 04:41 Info-saved-by-cmd.txt -rwxrwxrwx 1 marc users 10 May 31 04:31 parts -rwxrwxrwx 1 marc users 2097152000 May 31 04:06 sda1.ntfs-ptcl-img.gz.aa -rwxrwxrwx 1 marc users 247361656 May 31 04:08 sda1.ntfs-ptcl-img.gz.ab -rwxrwxrwx 1 marc users 823182034 May 31 04:31 sda2.ntfs-ptcl-img.gz.aa -rwxrwxrwx 1 marc users 36 May 31 03:45 sda-chs.sf -rwxrwxrwx 1 marc users 31744 May 31 03:45 sda-hidden-data-after-mbr -rwxrwxrwx 1 marc users 512 May 31 03:45 sda-mbr -rwxrwxrwx 1 marc users 315 May 31 03:45 sda-pt.parted -rwxrwxrwx 1 marc users 285 May 31 03:45 sda-pt.parted.compact -rwxrwxrwx 1 marc users 259 May 31 03:45 sda-pt.sf (I've been experimenting with various permissions trying to get this to work; that's why they're currently all "rwxrwxrwx"...) I've got my CZ LiveCD stuck in a (different) machine with a 160GB SATA disk that I'm fine with overwriting; although CZ doesn't show a directory listing, it does show that the correct folder is mounted as /home/partimag. But a moment later, after selecting either Beginner or Expert, I'm only presented with the "savedisk", "saveparts", and "exit" options. What am I doing wrong? I am confident that the initial backup was successful; I can post the log if desired, or any other information that might be germane. Edit: I've copied the contents of the folder onto a 16GB USB stick and set THAT as /home/partimag. Still nothing. What the hell is CZ looking for?

  Read the article

• Installing Glassfish 3.1 on Ubuntu 10.10 Server

  - by andand

  I've used the directions here to successfully install Glassfish 3.0.1 on an virtualized (VirtualBox and VMWare) Ubuntu 10.10 Server instance without any real difficulty not resolved by more closely following the directions. However when I try applying them to Glassfish 3.1, I seem to keep getting stuck at section 6. "Security configuration before first startup". In particular, there are some differences I noted: 1) There are two keys in the default keystore. The 's1as' key is still there, but another named 'glassfish-instance' is also there. When I saw this, I deleted and recreated them both along with a 'myAlias' key which I was going to use where needed. 2) When turning the security on it seems like part of the server thinks it's on, but others don't. For instances: $ /home/glassfish/bin/asadmin set server-config.network-config.protocols.protocol.admin-listener.security-enabled=true server-config.network-config.protocols.protocol.admin-listener.security-enabled=true Command set executed successfully. $ /home/glassfish/bin/asadmin get server-config.network-config.protocols.protocol.admin-listener.security-enabled server-config.network-config.protocols.protocol.admin-listener.security-enabled=true Command get executed successfully. $ /home/glassfish/bin/asadmin --secure list-jvm-options It appears that server [localhost:4848] does not accept secure connections. Retry with --secure=false. javax.net.ssl.SSLHandshakeException: Remote host closed connection during handshake Command list-jvm-options failed. $ /home/glassfish/bin/asadmin --secure=false list-jvm-options -XX:MaxPermSize=192m -client -Djavax.management.builder.initial=com.sun.enterprise.v3.admin.AppServerMBeanServerBuilder -XX: UnlockDiagnosticVMOptions -Djava.endorsed.dirs=${com.sun.aas.installRoot}/modules/endorsed${path.separator}${com.sun.aas.installRoot}/lib/endorsed -Djava.security.policy=${com.sun.aas.instanceRoot}/config/server.policy -Djava.security.auth.login.config=${com.sun.aas.instanceRoot}/config/login.conf -Dcom.sun.enterprise.security.httpsOutboundKeyAlias=s1as -Xmx512m -Djavax.net.ssl.keyStore=${com.sun.aas.instanceRoot}/config/keystore.jks -Djavax.net.ssl.trustStore=${com.sun.aas.instanceRoot}/config/cacerts.jks -Djava.ext.dirs=${com.sun.aas.javaRoot}/lib/ext${path.separator}${com.sun.aas.javaRoot}/jre/lib/ext${path.separator}${com.sun.aas.in stanceRoot}/lib/ext -Djdbc.drivers=org.apache.derby.jdbc.ClientDriver -DANTLR_USE_DIRECT_CLASS_LOADING=true -Dcom.sun.enterprise.config.config_environment_factory_class=com.sun.enterprise.config.serverbeans.AppserverConfigEnvironmentFactory -Dorg.glassfish.additionalOSGiBundlesToStart=org.apache.felix.shell,org.apache.felix.gogo.runtime,org.apache.felix.gogo.shell,org.apache.felix.gogo.command -Dosgi.shell.telnet.port=6666 -Dosgi.shell.telnet.maxconn=1 -Dosgi.shell.telnet.ip=127.0.0.1 -Dgosh.args=--nointeractive -Dfelix.fileinstall.dir=${com.sun.aas.installRoot}/modules/autostart/ -Dfelix.fileinstall.poll=5000 -Dfelix.fileinstall.log.level=2 -Dfelix.fileinstall.bundles.new.start=true -Dfelix.fileinstall.bundles.startTransient=true -Dfelix.fileinstall.disableConfigSave=false -XX:NewRatio=2 Command list-jvm-options executed successfully. Also the admin console responds only to http (not https) requests. Thoughts?

  Read the article

• How to make Linux reliably boot on multi-cpu machines?

  - by Adam Tabi

  I've got two machines, one with 4x12 AMD Opteron cores (AMD Opteron(tm) Processor 6176), one with 2x8 Xeon cores (HT disabled; Intel(R) Xeon(R) CPU E5-2660 0 @ 2.20GHz). On both machines I experience difficulties during boot of Linux using recent kernels. The system hangs during the initialization of the kernel, before or just when initramfs started initializing the hardware. The last thing which got displayed was a stacktrace like this: CPU: 31 PID: 0 Comm: swapper/31 Tainted: G D 3.11.6-hardened #11 Hardware name: Supermicro X9DRT-HF+/X9DRT-HF+, BIOS 3.00 07/08/2013 task: ffff880854695500 ti: ffff880854695a28 task.ti: ffff880854695a28 RIP: 0010:[<ffffffff8100a82e>] [<ffffffff8100a82e>] default_idle+0x6/0xe RSP: 0000:ffff8808546b3ec8 EFLAGS: 00000286 RAX: ffffffff8100a828 RBX: ffff880854695a28 RCX: 00000000ffffffff RDX: 0100000000000000 RSI: 0000000000000000 RDI: ffff88107fdec690 RBP: ffff8808546b3ec8 R08: 0000000000000000 R09: ffff880854695500 R10: ffff880854695500 R11: 0000000000000001 R12: ffff880854695a28 R13: ffff880854695a28 R14: ffff880854695a28 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff88107fde0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000002b43256a960 CR3: 00000000016b5000 CR4: 00000000000607f0 Stack: ffff8808546b3ed8 ffffffff8100aec9 ffff8808546b3f10 ffffffff8109ce25 334ab55852ec7aef 000000000000001f ffffffff8102d6c0 0000000000000000 0000000000000000 ffff8808546b3f48 ffffffff810276e0 ffff8808546b3f28 Call Trace: [<ffffffff8100aec9>] arch_cpu_idle+0x20/0x2b [<ffffffff8109ce25>] cpu_startup_entry+0xed/0x138 [<ffffffff8102d6c0>] ? flat_init_apic_ldr+0x80/0x80 [<ffffffff810276e0>] start_secondary+0x2c9/0x2f8 I compiled the kernel myself and it works fine, if I boot with nolapic. Yet, only one core is used. Also, the kernel of RHEL6 seems to work fine. I suspect that there are some patches used to make things work. Using the kernel config file from RHEL6 and building a more recent kernel yields the same problems. On the Xeon machine, things got better by disabling Hyperthreading completely. The machine now boots successfully on at least 4 out of 5 times. And if it boots, multicore stuff works just fine. However, I'm wondering about what to do about the AMD machine. So to sum it up: Gentoo kernel 3.6 - 3.11 won't reliably boot those machines unless you reduce the amount of cores (e.g. via nolapic). RHEL6 kernel (which is 2.6.32) boots just fine. RH kernel config used to build a 3.x kernel won't yield a working kernel. Not distribution specific (apart from the kernel being used). These stack traces got printed every minute or so. The kernel seems to be stuck in an endless loop. Yet, a recent kernel is needed for various reasons. So the question is: What does the RHEL6 kernel do, what vanilla or gentoo kernels don't do? Is there a boot option that might lead to a reliable boot with all the cores enabled? Best, Adam

  Read the article

• Providing reverse records for records that map to ISP IP

  - by thejartender

  I have been instructed to use my ISP ip (as a temporary fix for mapping my name server and domain records as my router dishes out rfc 1918 adresses to devices in my network where I am running an Ubuntu server, my router and my development laptop andso I have fixed: $TTL 3H @ IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); thejarbar.org. IN A 10.0.0.42 @ IN NS ns.thejarbar.org. yuccalaptop IN A 10.0.0.19 ns IN A 10.0.0.42 gw IN A 10.0.0.138 www IN CNAME thejarbar.org. To a temporary version of: $TTL 3H @ IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); thejarbar.org. IN A 88.89.190.171 @ IN NS ns.thejarbar.org. yuccalaptop IN A 10.0.0.19 ns IN A 88.89.190.171 gw IN A 10.0.0.138 www IN CNAME thejarbar.org. I am using bind and when using named-checkzone on this file according to my zone configurations, this file has no errors. I then run dig thejarbar.org @88.89.190.171 and get an expected authorative reply. My issue is creating my reverse DNS SOA zone and I would gratly appreciate assistance and guidance. I am stuck on how to represent the reverse records correctly for the eddresses that map to my isp IP. I am trying: $TTL 3H 0.0.10.in-addr.arpa. IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); 171.190.89.88. IN PTR thejarbar.org. 171.190.89.88. IN NS ns.thejarbar.org. 19 IN PTR yuccalaptop.thejarbar.org. 138 IN PTR gw.thejarbar.org. www IN PTR www.thejarbar.org. But running named-checkzone on this file leaves an erroneous return that IN: has no NS records I would greatly appreciate assistance

  Read the article

• TomCat starts, but does not load properly

  - by user37136

  Hey guys, I've been working on this for a day now and still don't know what's wrong. I am essentially building a second environment for our web and app server. I got apache to load up just fine, but tomcat is proving to be difficult. It appears to start and load just fine, but when it comes to loading our application, its just got stuck for 2-5 minutes and then shut down. Here is the log on the original machine where it works fine: 2010-02-12 11:52:40,506 INFO Web application servlet context is initializing... 2010-02-12 11:52:40,540 DEBUG Servlet context attribute added: select_jobType=[{1,Undefined}, {100,Completion}, {200,Plugging}, {300,R+M}, {400,Workover}, {500,Swab - tubing}, {600,Swab - fluid}] 2010-02-12 11:52:40,540 DEBUG Servlet context attribute added: select_jobTaskType=[{1,Undefined}, {100,Rod part}, {200,Tubing leak}, {300,Pump change}, {400,Stripping job}, {500,Long stroke}, {600,A/L optimization}] 2010-02-12 11:52:40,541 DEBUG Servlet context attribute added: select_wellType=[{1,Undefined}, {100,Rod pump}, {200,ESP}, {300,Injector}, {400,PC pump}, {500,Co-Rod}, {600,Flowing}, {700,Storage}] 2010-02-12 11:52:40,541 DEBUG Servlet context attribute added: select_assetType=[{1,Rig}, {100,Disabled rig}] 2010-02-12 11:52:40,542 DEBUG Servlet context attribute added: select_state=[{AL,Alabama}, {AK,Alaska}, {AZ,Arizona}, {AR,Arkansas}, {CA,California}, {CO,Colorado}, {CT,Connecticut}, {DE,Delaware}, {FL,Florida}, {GA,Georgia}, {HI,Hawaii}, {ID,Idaho}, {IL,Illinois}, {IN,Indiana}, {IA,Iowa}, {KS,Kansas}, {KY,Kentucky}, {LA,Louisiana}, {ME,Maine}, {MD,Maryland}, {MA,Massachusetts}, {MI,Michigan}, {MN,Minnesota}, {MS,Mississippi}, {MO,Missouri}, {MT,Montana}, {NE,Nebraska}, {NV,Nevada}, {NH,New Hampshire}, {NJ,New Jersey}, {NM,New Mexico}, {NY,New York}, {NC,North Carolina}, {ND,North Dakota}, {OH,Ohio}, {OK,Oklahoma}, {OR,Oregon}, {PA,Pennsylvania}, {RI,Rhode Island}, {SC,South Carolina}, {SD,South Dakota}, {TN,Tennessee}, {TX,Texas}, {UT,Utah}, {VT,Vermont}, {VA,Virginia}, {WA,Washington}, {WV,West Virginia}, {WI,Wisconsin}, {WY,Wyoming}, {ACO,Atlantic Coast Offshore}, {FOAK,Federal Offshore Alaska}, {NGOM,Northern Gulf of Mexico}, {PCO,Pacific Coastal Offshore}] 2010-02-12 11:52:40,542 INFO KeyviewContextMonitor.contextInitialized: Loaded drop-down lists:com/key/portal/web/common/lists.properties 2010-02-12 11:52:40,937 DEBUG Servlet context attribute added: org.apache.struts.action.SERVLET_MAPPING=*.do 2010-02-12 11:52:40,937 DEBUG Servlet context attribute added: org.apache.struts.action.ACTION_SERVLET=org.apache.struts.action.ActionServlet@155d578 2010-02-12 11:52:41,939 DEBUG Servlet context attribute added: org.apache.struts.action.MODULE=org.apache.struts.config.impl.ModuleConfigImpl@e08e9d 2010-02-12 11:52:41,962 DEBUG Servlet context attribute added: org.apache.struts.action.FORM_BEANS=org.apache.struts.action.ActionFormBeans@b31c3c 2010-02-12 11:52:41,967 DEBUG Servlet context attribute added: org.apache.struts.action.FORWARDS=org.apache.struts.action.ActionForwards@102c646 2010-02-12 11:52:41,973 DEBUG Servlet context attribute added: org.apache.struts.action.MAPPINGS=org.apache.struts.action.ActionMappings@127276a 2010-02-12 11:52:41,974 DEBUG Servlet context attribute added: org.apache.struts.action.MESSAGE=org.apache.struts.util.PropertyMessageResources@18cae13 2010-02-12 11:52:41,984 DEBUG Servlet context attribute added: org.apache.struts.action.PLUG_INS=[Lorg.apache.struts.action.PlugIn;@f875ae 2010-02-12 11:52:46,816 INFO Sucessfully loaded application properties com/key/core/properties/application On my second environment, it didn't execute the last line. I start tomcat with the exact same command line !/bin/ksh export JAVA_HOME=/app/java export CATALINA_HOME=/app/tomcat export CATALINA_BASE=/app/keyview/appserver CATALINA_OPTS=" -Xms128m -Xmx800m -Dapplication.props=com/key/core/properties/application -Dlog4j.configuration=com/key/core/log/log4j.xml -Djava.awt.headless=true -Dlog4j.debug" export CATALINA_OPTS ${CATALINA_HOME}/bin/startup.sh I bolded the line that I think are in error. Thanks

  Read the article

• Upgrading TFS 2005 to TFS 2010 fails at "Executing servicing step Upgrade Version Control Identities"

  - by nadeemmar

  Hi all, I have been trying to upgrade our TFS 2005 to TFS 2010 but with no luck so far. I went through the TFS Installation guide and many upgrade guides but with no luck in overcoming the issue I am facing which seems to be unique and different to other described issues. In our company, we have a domain forest with several domains. Lets say domain A, B, and C. TFS is in domain A and has users from all these three domains. All domains have trust reltionships between them. However, domain C was deleted several months ago. In the upgrade process, whenever I reach the collection upgrade step, the following error is raised: [Info @09:57:50.997] [2010-12-29 09:55:47Z][Informational] Step Data: ExtensionType = Microsoft.TeamFoundation.VersionControl.Server.PlugIns.WorkspaceSecurityNamespaceExtension [Info @09:57:50.997] [2010-12-29 09:55:47Z] Servicing step Create VersionControl Security Namespaces passed. (ServicingOperation: UpgradePreTfs2010Databases; Step group: Upgrade.TfsVersionControl) [Info @09:57:50.997] [2010-12-29 09:55:47Z] Executing servicing step Upgrade Version Control Identities. (ServicingOperation: UpgradePreTfs2010Databases; Step group: Upgrade.TfsVersionControl) [Info @09:57:50.997] [2010-12-29 09:55:47Z][Informational] Step Performer: VersionControl [Info @09:57:50.997] [2010-12-29 09:55:47Z][Informational] Step Type: UpgradeIdentity [Info @09:57:50.997] [2010-12-29 09:55:47Z][Informational] Step Data Text: [Error @09:57:50.997] [2010-12-29 09:55:51Z][Error] Sync error for identity: System.Security.Principal.WindowsIdentity, S-1-5-21-1004336348-527237240-682003330-2818 - The trust relationship between the primary domain and the trusted domain failed I looked for the SID and it seems to be for a user in the deleted domain C. With a bit of googling, I figured out that TFSConfig Identities command can be used to remap users from one domain to the other. I went ahead and created local users that matches the users we have from domain C and ran the TFSConfig Identities /Change command and it executed successfully. However, I still get the same error. I am stuck and can't figure out how to move forward :( I need your expertise, has anyone faced this issue before? Do I need to change these identities on TFS 2005 before I commence the upgrade? I forgot to mention, I am following the upgrade with a move approach. I created a virtual machine for testing the upgrade. Installed SQL server 2008, restored the TFS databases and installed TFS 2010 and ran the upgrade wizard. Regards, Nadeem

  Read the article

< Previous Page | 518 519 520 521 522 523 524 525 526 527 528 529  | Next Page >