Search Results

Search found 18791 results on 752 pages for 'edit lopez'.

Page 525/752 | < Previous Page | 521 522 523 524 525 526 527 528 529 530 531 532  | Next Page >

• How to configure networking on an appliance such that it can plug and play on any corporate network?

  - by Joshua Lim

  I had a chance to configure a Moxa NPort device server appliance on my client's network, it was very easy to do so, done in just 2 minutes. Here's what I did:- The Moxa device server had a preset IP address of 192.168.127.254 and subnet mask 255.255.255.0 - http://www.moxa.com/doc/manual/nport/5400/NPort_5400_Series_Users_Manual_v4.pdf Moxa provides a Windows software which I used to "scan" for the device server. It worked like magic! The software returns a list of device servers found. Each device server is identified by MAC address, and by selecting the device server using the software, I can reset the default IP address and subnet mask of that device server! In comparison, during an earlier project, I spent 2 hours trying to get KVM to work for a Windows 7 embedded appliance I'm trying to install in my client's network - http://superuser.com/questions/380305/how-to-configure-windows-7-professional-appliance-pc-on-my-clients-network-usin Prior to that, I have already tried pre-configuring the IP address and subnet mask to the one which my client provided, yet the appliance still can't connect to the client's network! I've also tried cross cable, didn't work either. After KVM worked, I discovered that the network settings were "lost" after I plug the machine into the client's network. Now my question is what can I do to setup my Windows 7 embedded appliance so that it can connect to any network like that the Moxa device server? I tried experimenting this on my network using a Windows machine configured to an IP address of 192.168.127.254 and subnet mask 255.255.255.0, but it doesn't connect to my network that uses 192.168.0.*. :( EDIT: I would like to point out that the Moxa Windows configuration software seems to be able to connect to any Moxa device connected to the network even if it is on a different subnet, as long as the network adapter shows "connected". This is important because the Moxa device has no VGSM port or interface to configure the IP address.

  Read the article

• Using gitlab behind Apache proxy all generated urls are wrong

  - by Hippyjim

  I've set up Gitlab on Ubuntu 12.04 using the default package from https://about.gitlab.com/downloads/ {edit to clarify} I've set up Apache to proxy and run the nginx server the package installed on port 8888 (or so I thought). As I had Apache installed already I have to run nginx on localhost:8888. The problem is, all images (such as avatars) are now served from http://localhost:8888, and all the checkout urls Gitlab gives are also localhost - instead of using my domain name. If I change /etc/gitlab/gitlab.rb to use that url, then Gitlab stops working and gives a 503. Any ideas how I can tell Gitlab what URL to present to the world, even though it's really running on localhost? /etc/gitlab/gitlab.rb looks like: # Change the external_url to the address your users will type in their browser external_url 'http://my.local.domain' redis['port'] = 6379 postgresql['port'] = 2345 unicorn['port'] = 3456 and /opt/gitlab/embedded/conf/nginx.conf looks like: server { listen localhost:8888; server_name my.local.domain; [Update] It looks like nginx is still listening on the wrong port if I don't specify localhost:8888 as the external_url. I found this in /var/log/gitlab/nginx/error.log 2014/08/19 14:29:58 [emerg] 2526#0: bind() to 0.0.0.0:80 failed (98: Address already in use) 2014/08/19 14:29:58 [emerg] 2526#0: bind() to 0.0.0.0:80 failed (98: Address already in use) 2014/08/19 14:29:58 [emerg] 2526#0: bind() to 0.0.0.0:80 failed (98: Address already in use) 2014/08/19 14:29:58 [emerg] 2526#0: bind() to 0.0.0.0:80 failed (98: Address already in use) 2014/08/19 14:29:58 [emerg] 2526#0: bind() to 0.0.0.0:80 failed (98: Address already in use) 2014/08/19 14:29:58 [emerg] 2526#0: still could not bind() Apache setup looks like: <VirtualHost *:80> ServerName my.local.domain ServerSignature Off ProxyPreserveHost On AllowEncodedSlashes NoDecode <Location /> ProxyPass http://localhost:8888/ ProxyPassReverse http://127.0.0.1:8888 ProxyPassReverse http://my.local.domain </Location> </VirtualHost> Which seems to proxy everything back ok if Gitlab listens on localhost:8888 - I just need Gitlab to start displaying the right URL, instead of localhost:8888.

  Read the article

• How to get german QWERTY on Windows?

  - by Arturas M

  Well I'm used to having the world standard keyboard which is qwerty and not qwertz... But on windows I can't find the choice for german input which would be qwerty, not qwertz. In linux there was german input with qwerty so it was fun. I believe it should be on Windows too? Cause i'm sick of this qwertz always having to correct and search for z or y... Yeah, I know, if Germans made a mistake, it wasn't loosing WW2... Edit: Maybe I wasn't clear enough, it's not about changing between different language inputs? It's about having all german keys in german input, just the z and y would be in the correct places like all the worlds keyboards use and like the US keyboard uses... Solution: Well unfortunately by searching everywhere and waiting for answers I couldn't find what I needed, so I came up with this solution - I used The The Microsoft Keyboard Layout Creator And created my own very custom layout by modifying the default german layout and switching places of z and y. In case somebody needs it and doesn't want to go the hard way, I decided to upload them, so here are the links to download and install the keyboard layout: http://www20.zippyshare.com/v/95071447/file.html http://rapidshare.com/files/3822150342/German%20QWERTY%202%20by%20Arturas%20M.zip It will appear as a choice under German input between languages in your language bar. If you just want to use this german layout, just remove all german layouts and install this one. Good luck and have fun using it!

  Read the article

• Gvim on Windows 7: ALT codes not working

  - by John Sonderson

  I would like to be able to enter ALT codes in Gvim on Windows 7 as documented on the following site: Alt Codes On Windows (Windows 7 in my case), to generate a character via an ALT code you make sure that the NumLock key on your keypad is toggled on, hold down the ALT key, enter the keycode on the numeric keypad, and then release the ALT key. However this does not work in Gvim on Windows (which ignores the fact that I am pressing the ALT key and just prints to entered keypad key directly onto the screen). How can I get these keystroke combinations to work in Gvim as well? Thanks. EDIT: As the answer below points out, the way to insert non-ASCII characters for which you do not have entries on your keyboard without changing the keyboard layout is as follows: Make sure you are in insert mode, and then type CTRL-V followed by the Unicode character code of interest, for instance: CTRL-V u00E0 (generates à) CTRL-V u00C8 (generates È) CTRL-V u00E8 (generates è) CTRL-V u00E9 (generates é) CTRL-V u00EC (generates ì) CTRL-V u00F2 (generates ò) etc... See for instance http://unicode-table.com/ for a full list of Unicode character codes. The following list of Unicode characters by language may also be useful: http://en.wikipedia.org/wiki/List_of_Unicode_characters In some cases such as this one, though, there might be an easier way to enter special characters (see :help digraphs and :digraphs). For example, while in insert mode you may be able to type the following: CTRL-K E! (yields É) CTRL-K a' (yields á) Note that as the following page shows: http://code.google.com/p/vim/source/browse/runtime/doc/digraph.txt Gvim 7.4 contains an even wider set of default digraphs than Gvim 7.3, thus providing convenience to an even broader set of languages. Regards.

  Read the article

• How to add a privilege to an account in Windows?

  - by mark

  Given: A VM running Windows 2008 I am logged on there using my domain account (SHUNRANET\markk) I have added the "Create global objects" privilege to my domain account: The VM is restarted (I know logout/logon is enough, but I had to restart) I logon again using the same domain account. It seems still to have the privilege: I run some process and examine its Security properties using the Process Explorer. The account does not seem to have the privilege: This is not an idle curiousity. I have a real problem, that without this privilege the named pipe WCF binding works neither on Windows 2008 nor on Windows 7! Here is an interesting discussion on this matter - http://social.msdn.microsoft.com/forums/en-US/wcf/thread/b71cfd4d-3e7f-4d76-9561-1e6070414620. Does anyone know how to make this work? Thanks. EDIT BTW, when I run the process elevated, everything is fine and the process explorer does display the privilege as expected: But I do not want to run it elevated. EDIT2 I equally welcome any solution. Be it configuration only or mixed with code. EDIT3 I have posted the same question on MSDN forums and they have redirected me to this page - http://support.microsoft.com/default.aspx?scid=kb;EN-US;132958. I am yet to determine the relevance of it, but it looks promising. Notice also that it is a completely coding solution that they propose, so whoever moved this post to the ServerFault - please reinstate it back in the StackOverflow.

  Read the article

• Windows Server 2008 backup VHD's - is it possible to mount/open in Windows 7?

  - by Simon

  Hi All, Is it possible to mount the VHD files created by the Windows Server 2008 backup utility onto a Windows 7 (release) client? Following an array failure I was very worried that there was a problem with both the backup sets on different USB drives as attaching the VHD to a Win 7 box did not show the expected structure (instead they behaved like unformatted disk space). Subsequently, I've attached the backup drive to a 2008r2 machine that I'd intended to be the replacement and the backup set can be browsed without issue (seemingly). When the new disks arrive I'll go through the recovery process and see where we are, but it looks promising so far. Is it simply the case that you can't take server created VHD's and mount them on desktop machines? (Rather than hyper-ventilating at the thought of years of lost photos and email, I'm now just mildly curious) Edit:One thing that has confused things is that the backup utility on Win7 is more restrictive about restoring from external devices than the equivilent on 2008r2. With r2, I can restore files 'from another server' and browse to external storage. Win7 only allows the back to be located on a network share. Once my box of new disks arrive and I've got something to restore onto, I'll move the smaller of the backup VHDs onto network storage reachable by Win7 and see if the VHD is readable. I haven't read up on the VHD process used by the backup app - I'm assuming it's a base VHD and differencing files used for incremental backups and that the restore app understands this. Finally: In retrospect the question should have been, 'can I restore a 2008r2 backup set via a Win 7 client' Thanks

  Read the article

• Deployment and Ownership issues

  - by kylemac

  As an extreme newbie, I am having difficulty managing ownership and permissions on my first box. What I can't figure out is how to deploy using one user, we will call him deploy and operate my php application with www-data user. Currently as it stands, I know my server runs as www-data through this function <?php echo(exec("whoami")); ?> but I am having to chown between deploy and www-data every time I deploy. There has got to be an easier way to deploy with one user and still run as www-data. EDIT: Here is the output from ls- l on the folder in question. You will see user deploy and group www-pub, the group is from an attempt to add the two different users to a new group and chown one of them in the hopes that they both would have the permissions (newb alert) drwxrwxr-x 4 deploy www-pub 4096 Mar 7 01:41 example.com I am using capistrano for deployment under the user deploy then once its done i chown to www-data, otherwise I can't use php to manipulate files. I am also unsure how to even change which user apache is running.

  Read the article

• how to prevent other computers from seeing our network computers through vpn

  - by Disco

  We have a local office domain consisting of Windows 7 and XP machines that is running on Windows Server 2008 R2. We also have users that connect via VPN into our network. My concern is that when a remote user opens up a folder, the Network section on the left side of the folder shows the remote user all the computer names in our local network. I would like to go about renaming our computers in the local network with more descriptive computer names, but I do not want the users off-site to be able to see these computer names by simply opening up a folder. (Granted, they can already do this, but our current naming scheme does not link computer names to users.) I would like to change our computer names so we can determine which computer belongs to which user more easily IF it can be done securely. How can I ensure that our local computer names are not showing up in the Network folder for remote, VPN-connected users? My online searches have turned up results where people are advised to turn off Network Sharing and Discovery, but that seems to only ensure that the local machine doesn't see other computer names. I want to prevent OUR computer names from showing up on OTHER computers, and I can't go into the VPN-connected computers and turn off THEIR Network Discovery settings. I would think there is a group policy that would control this but I have not found one yet and I don't know how I would apply it to VPN-connected computers. Thanks! EDIT: That's true, a Group Policy wouldn't run on users only connecting via VPN, good point. What about a VPN/router policy, then?

  Read the article

• How can I add subdomains of default accepted domain of Exchange 2010

  - by Christoph

  I have an Exchange 2010 that has several accepted domains. Now I want this server to accept - besides the default SMTP domain - all subdomains of the default domain. The documentation in Technet states When you create an accepted domain, you can use a wildcard character (*) in the address space to indicate that all subdomains of the SMTP address space are also accepted by the Exchange organization. For example, to configure Contoso.com and all its subdomains as accepted domains, enter *.Contoso.com as the SMTP address space. It is, however not possible to add e. g. *.contoso.com if contoso.com is already configured. Exchange complains in this case that the domain is already configured. It is also not possible to edit the "value", i. e. the domain name of an accepted domain. I know that I cannot modify the default accepted domain, but changing it to another does not help either, because the domain name itself can never be edited. The last idea was deleting the accepted domain and re-creating it with "*." prepended. This is, however, also impossible because it is of course not possible to delete or modify the default address policy and if a domain name is used in an address template it cannot be removed from the accepted domains. The question is: How can I make my Exchange 2010 server accept any subdomain of its default accepted domain with a wildcard?

  Read the article

• Has anyone managed to build php5-xapian on Ubuntu 12.04?

  - by jetboy

  As Xapian's been dropped from the Ubuntu repositories, I'm attempting to build my own .deb from the instructions here: http://article.gmane.org/gmane.comp.search.xapian.general/8855 http://beeznest.wordpress.com/2011/07/06/howto-build-your-own-binaries-of-php-xapian-bindings-for-debian/ I can only get things to progress beyond the first few seconds by leaving out 'rm debian/control', but if I do, it looks as if the Python and Ruby bindings are building and passing their versions of smoketest correctly. However, the PHP part of the build is failing with this error: /home/charlie/xapian-bindings-1.2.8/php/smoketest.php:38: include(xapian.php): failed to open stream: No such file or directory FAIL: smoketest.php There's a xapian.php file in /home/charlie/xapian-bindings-1.2.8/php/php5/ but if I copy it to /home/charlie/xapian-bindings-1.2.8/php/ or change the path to it in smoketest.php, the build fails right near the start with: dpkg-source: error: aborting due to unexpected upstream changes Unfortunately I'm out of my comfort zone building from source. Anyone got any ideas? Edit post James' answer: Builds fine if I follow instructions exactly. I built it on a test VM initially, but that didn't build the PHP package as PHP itself wasn't installed. Obvious gotcha, but worth mentioning. Installing generated the following error: Setting up php5-xapian (1.2.8-1) ... Processing triggers for libapache2-mod-php5 ... dpkg (subprocess): unable to execute installed post-installation script (/var/lib/dpkg/info/libapache2-mod-php5.postinst): Permission denied ssion denied dpkg: error processing libapache2-mod-php5 (--install): subprocess installed post-installation script returned error exit status 2 Errors were encountered while processing: libapache2-mod-php5 It's only a script for restarting Apache. Stopping Apache before running sudo dpkg -i php5-xapian_*.deb prevents the error. Xapian now shows up in phpinfo(). Job done. Thanks.

  Read the article

• Netgear GS724Tv3 and link aggregation Mac OS X Server 10.6.8

  - by Manca Weeks

  I need to link aggregate 2 sets of ports on the Netgear GS724T with my Apple server tower (latest generation). I have 2 built in ports and 2 ports on a PCIe ethernet card. It is not obvious to me how to properly configure the Netgear end. I have access to the Netgear box through its web interface, just don't know how to properly set the settings. I tried going to Netgear for help, but they said my software support has expired. I bought this unit on their recommendation - they say it is compatible with 802.3ad protocol. I cannot locate any references to this protocol in the manual and I noticed some people in formus say that this device is actually not compatible with 802.3ad and that Netgear is misleading potential customers by saying it is. Any help will be appreciated. Thanks, M My own answer - posted as edit because of restrictions on my user: OK folks, turns out one must use a Windows machine on this one or nothing makes sense. I was unable to get much farther than viewing the default inactive LAGs because in Firefox and Safari on Mac things don't make much sense - i.e. the Apply buttons (supposedly JavaScript) don't work. You can view the configurations, but none of the modifications you make stick. Then, in Switching - LAGs, choose the ports to include and make sure you switch the LAG type from Static to LACP and all is well. Haven't tested the performance of the config yet, but both sides appear to be happy with the configuration. Apple server says link active and so does the Netgear. Will report if any other discoveries. Thanks for all who read and to user84104 for responding. M

  Read the article

• RHEL 5.2 installing on ProLiant BL460c - hangs at 'now booting the kernel'

  - by Dr Rocket Mr Socket

  As the title states, I have a problem. This server and the installation disc are also on the other side of the world to me so... So far, I have tried to start the install with the parameters: linux text noapic noacpi no=apic no=acpi which results in the same hang. I have also disabled a PCI ethernet adapter, I am uneasy about disabling the onboard ethernet adapter I do not know if ILO uses this. Anyone have any advice? Much appreciated. EDIT: full output after trying to begin the installation. boot: linux text Loading initrd.img.................. Loading vmlinuz....... Uncompressing Linux...done. Now booting the kernel stays on this for hours EDIT2: adding the 'mem=40960M' (server has 40 gigs of ram) parameter allows it to proceed but the following output directly after 'Now booting the kernal' Memory: sized by int13 0e801h initrd extends beyond end of memory (0x00ef2090 > 0x00000000) disabling initrd Console: 16 point font, 400 scans Console: colour VGA+ 80x25, 1 virtual console (max 63) pcibios_init : BIOS32 Service Directory Structure at 0x000ffee0 pcibios_init : BIOS32 Service Directory entry at 0xf0000

  Read the article

• Is there a Windows 7 compatible IPSec VPN client that allows protocol and port specific rules?

  - by Sani Huttunen

  As the title says, I need to find a IPSec VPN client for Windows 7. On XP and Vista we've used SafeNet SoftRemote in which you can set up rules for specific protocols and ports. But SoftRemote isn't compatible with Windows 7. 172.xxx.xxx.1 TCP 1433 172.xxx.xxx.2 TCP 1433 172.xxx.xxx.10 ALL ... Since the VPN gateway is configured this way the client must mirror these settings. I've tried TheGreenBow, NCP Secure Entry, Cisco VPN Client and Shrew Soft VPN but none of these allows you to configure by protocol and port. Does anyone have any other suggestions? EDIT: Forgot to mention that agressive mode is also a requirement. --UPDATE-- I've got some news... I've managed to get SoftRemote to work on Windows 7 x64 through Windows XP Mode. After scouring all corners of the Internet for idéas I had enough information to construct a working solution. This solution will probably benefit other clients as well! You'll find a post here with detailed instructions of how I went about.

  Read the article

• Moving a lotus database causes incoming mail failure

  - by Logman

  Hey all, I moved a couple lotus note databases to another hd (ran out of space) by using a directory link/pointer on the domino server. USed a text file with the .DIR ext with the desired new path etc... well that works fine. I open up a lotus notes client, use the id and then OPEN the database. The directory link works fine, the new location of the db is opened with no problems. We found out that we couldnt FORWARD any mail: We did the following to make it work: Goto menu FILE|MOBILE|EDIT CURRENT LOCATION Goto tab MAIL and enter the correct path for "Mail File:" example: it should read "mail\morespace\flabor" and not "mail\flabor" "morespace" = directory link/pointer we can forward and reply to emails fine after that fix. The problem is that the user has no incoming email. Domino is still trying to send the incoming mail of that user to its old db location "mail\flabor" instead of "mail\morespace\flabor". Delivery error saying user does not exist. Is this a cache problem? We have reset the server ("Q" at the prompt), though we have not completely shut it down though. Thanks Frank

  Read the article

• Enabling mod_wsgi in Apache for a Django app on Gentoo

  - by hobbes3

  I installed Apache, Django, and mod_wsgi on Gentoo using emerge (on Amazon EC2). I know that the mod_wsgi is configured in /etc/apache2/modules.d/70_mod_wsgi.conf: <IfDefine WSGI> LoadModule wsgi_module modules/mod_wsgi.so </IfDefine> # vim: ts=4 filetype=apache So in my /etc/conf.d/apache I added the WSGI module: APACHE2_OPTS="-D DEFAULT_VHOST -D INFO -D SSL -D SSL_DEFAULT_VHOST -D LANGUAGE -D WSGI" But when I try to list the loaded module, mod_wsgi isn't listed. root ~ # apache2 -M | grep wsgi Syntax OK I also know that mod_wsgi isn't loading properly because the Apache configuration file doesn't recognize WSGIScriptAlias. By the way for Django to work I need to include a custom Apache configuration file. Where should I insert the line below? Include "/var/www/localhost/htdocs/mysite/apache/apache_django_wsgi.conf" I currently have that in the httpd.conf file but I feel like that file will get reseted whenever I upgrade Gentoo or related package. EDIT: it seems the mod_wsgi file is located in /usr/lib64/apache2/modules/mod_wsgi.so. Here is my detailed Apache settings: root@ip-99-99-99-99 /usr/portage/eclass # apache2 -V Server version: Apache/2.2.21 (Unix) Server built: Mar 7 2012 06:52:30 Server's Module Magic Number: 20051115:30 Server loaded: APR 1.4.5, APR-Util 1.3.12 Compiled using: APR 1.4.5, APR-Util 1.3.12 Architecture: 64-bit Server MPM: Prefork threaded: no forked: yes (variable process count) Server compiled with.... -D APACHE_MPM_DIR="server/mpm/prefork" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=128 -D HTTPD_ROOT="/usr" -D SUEXEC_BIN="/usr/sbin/suexec" -D DEFAULT_PIDLOG="/var/run/httpd.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_LOCKFILE="/var/run/accept.lock" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="/etc/apache2/mime.types" -D SERVER_CONFIG_FILE="/etc/apache2/httpd.conf"

  Read the article

• Estimating compressed file size using a list parameter

  - by Sai

  I am currently compressing a list of files from a directory in the following format: tar -cvjf test_1.tar.gz -T test_1.lst --no-recursion The above command will compress only those files mentioned in the list. I am doing this because this list is generated such that it fits a DVD. However, during compression the compression rate decreases the estimated file size and there is abundant space left in the DVD. This is something like a Knapsack algorithm. I would like to estimate the compressed file size and add some more files to the list. I found that it is possible to estimate file size using the following command: tar -cjf - Folder/ | wc -c This command does not take a list parameter. Is there a way to estimate compressed file size? I am also looking into options like perl scripts etc. Edit: I think I should provide more information since I have been doing a lot of web search. I came across a perl script(Link)that sort of emulates the Knapsack algorithm. The current problem with the above mentioned script is that it splits the files in their original state. When I compress the files after splitting them, there are opportunities for adding more files which I consider to be inefficient. There are 2 ways I could resolve the inefficiency: a) Compress individual files and save them in a directory using a script. The compressed file could provide a best estimate. I could generate a script using a folder of compressed files and use them on the uncompressed ones. b) Check whether the compressed file's size is less than the required size. If so, I should keep adding files until I meet the requirement. However, the addition of new files to the compressed file is an optimization problem by itself.

  Read the article

• Outlook, Word, and normal.dot (2003 Edition)

  - by mosiac

  I have one user that for some reason has been having macro issues with her normal.dot file. At first the fix was just remove the file because she isn't actually needing to save anything. This was really a temp fix. We found out that for some reason every time she opened up word it was trying to modify normal.dot but not asking. I set it up to ask so at least we could control the changes going on to normal.dot. There was one file disabled in Word that we enabled because it was a document she never used anymore, making us think that maybe that was the issue. We have automatic antivirus updates and scans so there is little chance of a virus. The issue has stopped as far as just using Word itself. She can open, close, edit, save, etc and never get the dialog. In Outlook however if she clicks reply or forward to an e-mail but decides not to send it, and just close it. She gets the pop up to save changes to normal.dot. This leads me to believe something in outlook about how she is setup to use Word as an e-mail editor is causing the problem. Am I even on the right track here? Short form: Word works fine with normal.dot, as an Outlook mail editor wants to change normal.dot. No idea what to do.

  Read the article

• Installing and running a guest OS on KVM-qemu with only serial console access

  - by nixnotwin

  I am trying to installing a bsd distro with virt-installer. With a Linux distro I used this: virt-install -n debian -r 1024 --vcpus=1 --accelerate -v --disk /var/kvm/installation-disks/debian.img,size=6--nographics --network=bridge:br0,model=ne2k_pci,mac=52:54:00:66:68:09 -l http://ftp.de.debian.org/debian/dists/squeeze/main/installer-amd64/current/images/ -x console=ttyS0,115200 This loads the installer directly from the online mirror. With Fedora I used this mirror: http://www.nic.funet.fi/pub/mirrors/fedora.redhat.com/pub/fedora/linux/releases/16/Fedora/x86_64/os/ Are there such mirrors for freebsd or openbsd? The reason I want direct installable ftp/http mirrors is because I can access my physical server only via ssh, and it doesn't have a X server or a window manager to give me a VNC GUI. When I tried installing centos 6 with an online mirror I was able to finish the installation via serial console, but after I rebooted it, the serial console never worked for me. I tried everything possible---editing menu.lst, inttab and securtty files. Fedora 16 booted fine from serial console, but got stuck when it loaded anaconda installer. I tried editing freebsd iso installation media by adding serial console option to boot option. And installation was successful. But couldn't boot into it becuase it wasn't giving console acess. I couldn't edit any files as ufs partition cannot be loaded with write access on my Ubuntu server 10.04. Only debian squeeze worked well, it worked for me even without editing a single configuration file. I want to have CLI versions of fedora/centos and freebsd/openbsd. But, looks like there isn't any hope for me to have them, as I have to depend on a serial console to do everything.

  Read the article

• Eee PC Seashell series netbook screen is cut off at bottom no matter the resolution

  - by Yzmir Ramirez

  I have an Eee PC 1015PE Seashell netbook running Windows 7 Home Premium with an Intel Graphics Media Accelerator 3150 (8.14.10.2230) with a "Generic Non-PnP Monitor" detected. I tried: Changing the resolution (Control Panel = Appearance and Personalization = Display = Screen Resolution) to 1024x768 Updating the video driver (to 8.14.10.2230) Uninstalling the driver and rebooting Pressing the Windows Key + "-" (magnifier) Pressing Ctrl + Mouse Scroll only resizes the desktop items Pressing Fn + F4 shows 1024x600 (which I think is what I should be using, but nothing happens) EDIT: Changed from Landscape to Portrait and it works Attached an External Monitor and when I extend or set as desktop it works only on the External Monitor (shows up as "Generic PnP Monitor in Device Manager) Basically the bottom inch of my desktop is off-screen hiding my start bar, but my wigets are in their proper position (the start bar is not hidden). Pressing Ctrl + Esc shows the start menu but its cut-off. I'm pretty sure I should be using 1024x600 resolution, any advice? What's odd is that this only started happening recently. EDIT2: Here are some screenshots showing the problem: Resized Window to fit: Opened Start Menu - notice it cut off: Maximized window and then scrolled down - notice no Start Menu: I downgraded my graphic driver I downloaded from the Intel Download Center for the Graphic Media Accelerator 3150 (now: 8.14.10.1972) and now my "Generic non-PnP Montior" detects as "Digital Flat Panel (1024x768 60Hz)".

  Read the article

• Write Fedora.iso to USB and boot it from a Macbook

  - by MTilsted

  I have an .iso image of the full Fedora 16 install (Downloaded from http://fedoraproject.org/en/get-fedora-options#formats as "Fedora 16 DVD") and the question now is: How do I write it on a USB stick, so I can install it on my Mac book? I tried using DD as the install guide said, and that gave me a USB stick which can boot from my PC. But it can't boot from the Mac (The Mac start menu don't show it as a boot option). Edit: I downloaded a live install image, and did this (SSD is my USB 4GB thing) /sbin/mkdosfs -F 32 -n usbdisk /dev/dev/sdd1 sudo livecd-iso-to-disk --format --reset-mbr --efi /tmp/download/Fedora-16-i686-Live-KDE.iso /dev/sdd1 And this produced an image which can boot on my pc but not on my mac. This seems to indicate that the --efi is not working, because if it really was EFI it would not boot on a normal pc, would it? I then tried this: (Difference being that I write the image directory to /dev/sdd instead of /dev/sdd1) but this still will not boot on the Mac (it newer shows up at the startup screen on the Mac). sudo livecd-iso-to-disk --format --reset-mbr --efi /tmp/download/Fedora- PS: My host Linux is Fedora 13.

  Read the article

• Is my laptop battery dead?

  - by Josh

  Recently my laptop battery will get extremely hot (definitely hotter than it should get) when I charge it. After that I usually end up removing it once it's fully charged to let it cool down, which takes a couple hours... Question is, is my battery dead? My last battery I had that died just ended up lasting 2 - 3 minutes on battery, no weird heat issues. And is there any way to possibly fix this? Probably not but I won't be able to get a replacement anytime soon. UPDATE: A few days ago when this happened and it cooled down, assuming it was fully charged, I ran my laptop on battery, and the battery life lasted about 10 minutes and then the laptop shutdown. I then plugged it in later and charged it back up, and for a while I had a orange light blinking on my laptop - which I assumed meant the battery was dead, especially since I got 10 minutes battery life. Then today, I turned my laptop on and was surprised to see that the battery was at 20% and charging (it's been plugged in since the incident above, so it should have been fully charged when I shut it off) I let it charge up, and as usual it got pretty hot around the time it was fully charged. So I turned my laptop off and pulled the battery out to let it cool down Now the thing is, just now I tried running it on battery, and it's been going for an hour now... so maybe its not dead? (also the orange light is no longer blinking...) Thanks in advance if anyone knows whats going on, and how to fix it, if its fixable =] EDIT: Some info if it helps... my laptop is about 2 years ago, and it's an Asus K50ID. I know laptop batteries usually don't last more than a year but I'm trying to keep this one going for as long as I can.

  Read the article

• DNS stops working occasionally

  - by Andrey

  I have tried using Google DNS and the one provided with DHCP. At some point my PC (Windows 7) stops resolving domain names, but DNS server is perfectly pingable. What can be the reason? Thanks! Edit: It is really weird. It can stop and start working in few seconds. The problem is that DNA requests are timing out, and the problem is that the DNS server is pingable at the same time. I can't understand how this could be possible and what might be an issue. C:\Windows\System32\drivers\etc>nslookup google.com DNS request timed out. timeout was 2 seconds. Server: UnKnown Address: 8.8.8.8 Non-authoritative answer: Name: google.com Addresses: 173.194.78.102 173.194.78.101 173.194.78.139 173.194.78.113 173.194.78.100 173.194.78.138 C:\Windows\System32\drivers\etc>nslookup google.com DNS request timed out. timeout was 2 seconds. Server: UnKnown Address: 8.8.8.8 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to UnKnown timed-out

  Read the article

• IIS URl Rewrite working inconsistently?

  - by Don Jones

  I'm having some oddness with the URL rewriting in IIS 7. Here's my Web.config (below). You'll see "imported rule 3," which grabs attempts to access /sitemap.xml and redirects them to /sitemap/index. That rule works great. Right below it is imported rule 4, which grabs attempts to access /wlwmanifest.xml and redirects them to /mwapi/wlwmanifest. That rule does NOT work. (BTW, I do know it's "rewriting" not "redirecting" - that's what I want). So... why would two identically-configured rules not work the same way? Order makes no different; Imported Rule 4 doesn't work even if it's in the first position. Thanks for any advice! EDIT: Let me represent the rules in .htaccess format so they don't get eaten :) RewriteEngine On # skip existing files and folders RewriteCond %{REQUEST_FILENAME} -s [OR] RewriteCond %{REQUEST_FILENAME} -l [OR] RewriteCond %{REQUEST_FILENAME} -d RewriteRule ^.*$ - [NC,L] # get special XML files RewriteRule ^(.*)sitemap.xml$ /sitemap/index [NC] RewriteRule ^(.*)wlwmanifest.xml$ /mwapi/index [NC] # send everything to index RewriteRule ^.*$ index.php [NC,L] The "sitemap" rewrite rule works fine; the 'wlwmanifest' rule returns a "not found." Weird.

  Read the article

• 1and1 ssh - connection refused

  - by kitensei

  I'm having troubles connecting through SSH to my 1&1 account. When I try to connect with command userXXX@host -p22 -vv I have the following output: OpenSSH_5.8p1 Debian-7ubuntu1, OpenSSL 1.0.0e 6 Sep 2011 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to mySite.com [ip_here] port 22. debug1: connect to address ip_here port 22: Connection refused Moreover, once I try to connect through SSH and it fails, even the HTTP access is dead, I cannot access the website through explorer anymore :/ please help < I'm running ubuntu 11.10 EDIT: don't know if it can help, here's the .htaccess of the 1and1 server Options +Indexes Satisfy any Order Deny,Allow Allow from 212.227.X.X Deny from all RemoveType .html .gif AuthType Basic AuthName "Access to /logs" AuthUserFile /kunden/homepages/43/d376072470/htpasswd Require user "user_here" and sftp.log: Mar 26 09:21:24 193.251.X USER_HERE Connection from 193.251.X port 51809 Mar 26 09:21:30 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:39 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:41 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:45 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:57 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 10:53:36 212.227.X tmp64459736-3228 Connection from 212.227.X port 23275 Mar 26 10:53:36 212.227.X tmp64459736-3228 Accepted password for tmp64459736-3228 from 212.227.X port 23275 ssh2 Mar 26 11:53:37 212.227.X tmp64459736-3228 Connection closed by 212.227.X Mar 26 18:58:17 212.227.X tmp64459736-5363 Connection from 212.227.X port 23353 Mar 26 18:58:17 212.227.X tmp64459736-5363 Accepted password for tmp64459736-5363 from 212.227.X port 23353 ssh2 Mar 26 19:53:36 212.227.X tmp64459736-8525 Connection from 212.227.X port 5166 Mar 26 19:53:36 212.227.X tmp64459736-8525 Accepted password for tmp64459736-8525 from 212.227.X port 5166 ssh2 Mar 26 19:58:17 212.227.X tmp64459736-5363 Connection closed by 212.227.X

  Read the article

• HTTP Error: 413 Request Entity Too Large

  - by Torben Gundtofte-Bruun

  What I have: I have an iPhone app that sends HTTP POST requests (XML format) to a web service written in PHP. This is on a hosted virtual private server so I can edit httpd.conf and other files on the server, and restart Apache. The problem: The web service works perfectly as long as the request is not too large, but around 1MB is the limit. After that, the server responds with: <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>413 Request Entity Too Large</title> </head><body> <h1>Request Entity Too Large</h1> The requested resource<br />/<br /> does not allow request data with POST requests, or the amount of data provided in the request exceeds the capacity limit. </body></html> The web service writes its own log file, and I can see that small messages are processed fine. Larger messages are not logged at all so I guess that something in Apache rejects them before they even reach the web service? Things I've tried without success: (I've restarted Apache after every change. These steps are incremental.) hosting provider's web-based configuration panel: disable mod_security httpd.conf: LimitXMLRequestBody 0 and LimitRequestBody 0 httpd.conf: LimitXMLRequestBody 100000000 and LimitRequestBody 100000000 httpd.conf: SecRequestBodyLimit 100000000 At this stage, Apache's error.log contains a message: ModSecurity: Request body no files data length is larger than the configured limit (1048576) It looks like my step #4 didn't really take, which is consistent with step #1 but does not explain why mod_security appears to be active after all. What more can I try, to get the web service to receive large messages?

  Read the article

< Previous Page | 521 522 523 524 525 526 527 528 529 530 531 532  | Next Page >