Search Results

Search found 16644 results on 666 pages for 'traffic management'.

Page 528/666 | < Previous Page | 524 525 526 527 528 529 530 531 532 533 534 535  | Next Page >

• Firebox 1250e Core Failing?

  - by Noah

  We have 2 Firebox 1250e Core firewall boxes in our production environment, serving as an active and passive mode. A few months back, the active box was flashing a warning light, so our consultant removed it, and plugged it in to a test network. Everything appeared to be working fine, so he reloaded it into the production environment, and we didn't see any other issues. Fast forward to last week, and out network was constantly dropping connections over RDC, timing out, and performing as if there was a traffic issue. I turned off the production box and everything began to work fine immediately. At this point though, I'm not sure how to proceed. Should the box be completely replaced? Is there any recommended testing we could do to determine if there is a failure of some type with this device? Should we try upgrading the software on it? I know the environment isn't the issue, since the passive box (which is now the active one) is working fine. We'd like to have 2 in production though for safety failover purposes. I am not a network admin, but am hoping someone here might be able to provide some guidance.

  Read the article

• My linux server "Number of processes created" and "Context switches" are growing incredibly fast

  - by Jorge Fuentes González

  I have a strange behaviour in my server :-/. Is a OpenVZ VPS (I think is OpenVZ, because /proc/user_beancounters exists and df -h returns /dev/simfs drive. Also ifconfig returns venet0). When I do cat /proc/stat, I can see how each second about 50-100 processes are created and happens about 800k-1200k context switches! All that info is with the server completely idle, no traffic nor programs running. Top shows 0 load average and 100% idle CPU. I've closed all non-needed services (httpd, mysqld, sendmail, nagios, named...) and the problem still happens. I do ps -ALf each second too and I don't see any changes, only a new ps process is created each time and the PID is just the same as before + 1, so new processes are not created, so I thought that process growing in cat /proc/stat must be threads (Yes, seems that processes in /proc/stat counts threads creation too as this states: http://webcache.googleusercontent.com/search?q=cache:8NLgzKEzHQQJ:www.linuxhowtos.org/System/procstat.htm&hl=es&tbo=d&gl=es&strip=1). I've changed to /proc dir and done cat [PID]\status with all PIDs listed with ls (Including kernel ones) and in any process voluntary_ctxt_switches nor nonvoluntary_ctxt_switches are growing at the same speed as cat /proc/stat does (just a few tens/second), Threads keeps the same also. I've done strace -p PID to all process too so I can see if any process is crating threads or something but the only process that has a bit of movement is ssh and that movement is read/write operations because of the data is sending to my terminal. After that, I've done vmstat -s and saw that forks is growing at the same speed processes in /proc/stat does. As http://linux.die.net/man/2/fork says, each fork() creates a new PID but my server PID is not growing! The last thing I can think of is that all process data that proc/stat and vmstat -s show is shared with all the other VPS stored in the same machine, but I don't know if that is correct... If someone can throw some light on this I would be really grateful.

  Read the article

• Network Load Balancing, intermittent port problem on Windows Server 2008

  - by Jimmy Chandra

  Trying to troubleshoot an intermittent problem on a Windows Server 2008 NLB. I think it might be related to an NLB issue. We are using Windows Network Load Balancing to balance load for our multiserver SharePoint front ends. Say... Web Front End 1 IP is 192.168.1.100 and Web Front End 2 IP is 192.168.1.101, the NLB is setup to load balance both WFE servers on any incoming traffic to the IP 192.168.1.200. Sometimes we got an intermittent issue where when we try to access the SharePoint site using 192.168.1.200:8080 (say the site is set up to run on port 8080) from a remote client, it will display page not found. Pinging the 192.168.1.200 will give responses, but when trying to telnet to 192.168.1.200:8080 it just won't connect. However, browsing the SharePoint site directly on individual WFE (192.168.1.100 and 192.168.1.101) show no problem whatsoever. My guess also (we didn't get a chance to try it yet, but I think it should work), if I try connecting remotely to individual server, it will respond just fine. But any attempt on trying to connect using the virtual IP (192.168.1.200) will fail miserably. Funny thing is, after a while it will return back to normal. Anyone had similar experience with this type of problem while implementing NLB before? We are doing this in a virtual environment.

  Read the article

• OpenVPN (Tunnelblick) Suddenly Dropping Constantly

  - by Jeremy Privett

  I've been using Tunnelblick on my Mac for OpenVPN for about a year now. All of a sudden, this morning, it decided that it was going to take a nasty turn for the worse with no explanation. Here are the symptoms I'm seeing: I can connect to the VPN fine, initially. After about 2 - 5 minutes of no interruption, the connection suddenly dies. I can still see the VPN route using netstat -rn, and Tunnelblick believes it's still connected. No VPN traffic can go through and I can't even ping the VPN gateway. Eventually, Tunnelblick will catch on that the connection has died (usually about 5 - 10 minutes later) and shoot itself to restart and then the cycle starts over again. I've tried everything I can think of to figure this one out. I've completely flushed my system by rebooting and removing Tunnelblick and all traces of OpenVPN from my system and re-installing from scratch. No dice, same problem. I'm at my wits end, because I desperately need to get this fixed as the VPN is required for me to be able to do my job. Any ideas you have would be greatly appreciated.

  Read the article

• Bridging my laptop's wireless and wired adaptors

  - by stacey.richards

  I would like to be able to connect a desktop computer that does not have a wireless adapter to my wireless network. I could just run a network cable from my ADSL/wireless router to the desktop computer but sometimes this is not practical. What I would really like to do is bridge my laptop's wireless and wired adapters in such a way that I can run a network cable from my laptop to a switch and another network cable from the switch to a desktop computer so that the desktop computer can access the Internet through my ADSL/wireless router via my latop: +--------------------+ |ADSL/wireless router| +--------------------+ | +-------------------------+ |laptop's wireless adaptor| | | |laptop's wired adaptor | +-------------------------+ | +------+ |switch| +------+ | +-----------------------+ |desktop's wired adapter| +-----------------------+ A bit of Googling suggests that I can do this by bridging my laptop's wireless and wired adapters. In Windows XP's Network Connections I select both the Local Area Connection and the Wireless Network Connection, right click and select Bridge Connections. From what I gather, this (layer 2?) bridge will examine the MAC address of traffic coming from the wireless network and pass it through to the wired network if it suspects that a network adapter with that MAC address may be on the wired side, and vice-versa. If this is the case, I would assume that when the desktop computer attempts to get an IP address from a DHCP server (which is running on the ADSL/wireless router), it would send a DHCP broadcast packet which would pass through the laptop's bridge to the router and the reply would return through the laptop's bridge back to the desktop. This doesn't happen. With some more Googling I find some instruction how this can be done with Linux. I reboot to Ubuntu 9.10 and type the following: sudo apt-get install bridge-utils sudo brctl addbr br0 sudo brctl addif br0 wlan0 sudo brctl addif br0 eth0 sudo ipconfig wlan0 0.0.0.0 sudo ipconfig eth0 0.0.0.0 Once again, the desktop cannot reach the ADSL/wireless router. I suspect that I'm missing some simple important step. Can anyone shed some light on this for me?

  Read the article

• Unable to PPTP through NAT on Cisco 881

  - by MasterRoot24

  I'm trying to connect to a PPTP server which is sat behind a Cisco 881 NAT router. The server is running Ubuntu Server 12.04 and is running Poptop pptpd as the PPTP daemon listening for connections. As discussed in my other question, I'm trying to setup a Cisco 881 router to replace my old Linksys WAG320N. This same server and WAN connection worked fine with the WAG320N with no special configuration, other than allowing 1723 in through the firewall. On the Cisco 881, I'm using the newer ip nat enable or NAT NVI to setup static routes in through the firewall for the services running behind the router. My reason being that I can't run another copy of my live DNS domains internally with local IP addresses in. For the purposes of this question, though, I have rebuilt the router with ip nat inside/outside style NAT'ing, but this issue is still apparent. HTTP/SMTP/IMAP etc. all work ok from both the WAN and LAN interfaces of the router. I'm only having issues with SIP (see other question) and PPTP. My issue is that the GRE doesn't appear to be passing through NAT correctly and one end of the connection is not receiving GRE traffic when it should be, so the server hangs up the connection. Here's an example of /var/log/syslog with debug enabled in /etc/pptpd.conf: Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: MGR: Launching /usr/sbin/pptpctrl to handle client Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: local address = 192.168.1.50 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: remote address = 192.168.1.51 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: pppd options file = /etc/ppp/pptpd-options Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Client 82.132.248.216 control connection started Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Received PPTP Control Message (type: 1) Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Made a START CTRL CONN RPLY packet Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: I wrote 156 bytes to the client. Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Sent packet to client Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Received PPTP Control Message (type: 7) Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Set parameters to 100000000 maxbps, 64 window size Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Made a OUT CALL RPLY packet Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Starting call (launching pppd, opening GRE) Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: pty_fd = 6 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: tty_fd = 7 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: I wrote 32 bytes to the client. Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Sent packet to client Dec 11 21:06:30 <HOSTNAME> pptpd[22627]: CTRL (PPPD Launcher): program binary = /usr/sbin/pppd Dec 11 21:06:30 <HOSTNAME> pptpd[22627]: CTRL (PPPD Launcher): local address = 192.168.1.50 Dec 11 21:06:30 <HOSTNAME> pptpd[22627]: CTRL (PPPD Launcher): remote address = 192.168.1.51 Dec 11 21:06:30 <HOSTNAME> pppd[22627]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Dec 11 21:06:30 <HOSTNAME> pppd[22627]: pppd 2.4.5 started by root, uid 0 Dec 11 21:06:30 <HOSTNAME> pppd[22627]: Using interface ppp0 Dec 11 21:06:30 <HOSTNAME> pppd[22627]: Connect: ppp0 <--> /dev/pts/3 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: GRE: Bad checksum from pppd. Dec 11 21:06:31 <HOSTNAME> pptpd[22626]: CTRL: Received PPTP Control Message (type: 15) Dec 11 21:06:31 <HOSTNAME> pptpd[22626]: CTRL: Got a SET LINK INFO packet with standard ACCMs Dec 11 21:07:00 <HOSTNAME> pppd[22627]: LCP: timeout sending Config-Requests Dec 11 21:07:00 <HOSTNAME> pppd[22627]: Connection terminated. Dec 11 21:07:00 <HOSTNAME> avahi-daemon[1042]: Withdrawing workstation service for ppp0. Dec 11 21:07:00 <HOSTNAME> pppd[22627]: Modem hangup Dec 11 21:07:00 <HOSTNAME> pppd[22627]: Exit. Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: GRE: read(fd=6,buffer=6075a0,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: Reaping child PPP[22627] Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: Client 82.132.248.216 control connection finished Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: Exiting now Dec 11 21:07:00 <HOSTNAME> pptpd[5803]: MGR: Reaped child 22626 As far as Cisco are concerned, all I need is ip nat source static tcp <SERVER LAN IP> 1723 interface FastEthernet4 1723 but of course this doesn't seem to the be helping the GRE traffic through as it should. Trying the connection to the LAN IP of the server from the same LAN as the server (behind the router), the PPTP connection works fine, so I'm confident that the server's config is ok. Furthermore, all I needed on my WAG320N was to open 1723 in the firewall. Here's my current router config: ! ! Last configuration change at 20:20:15 UTC Tue Dec 11 2012 by xxx version 15.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname xxx ! boot-start-marker boot-end-marker ! ! enable secret 4 xxxx ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 ! crypto pki trustpoint TP-self-signed-xxx enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-xxx revocation-check none rsakeypair TP-self-signed-xxx ! ! crypto pki certificate chain TP-self-signed-xxx certificate self-signed 01 xxx quit ip gratuitous-arps ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ! ! ! ! ! ip domain list dmz.xxx.local ip domain list xxx.local ip domain name dmz.xxx.local ip name-server 192.168.1.x ip cef login block-for 3 attempts 3 within 3 no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO881-SEC-K9 sn xxx ! ! username admin privilege 15 secret 4 xxx username joe secret 4 xxx ! ! ! ! ! ip ssh time-out 60 ! ! ! ! ! ! ! ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 switchport access vlan 2 no ip address ! interface FastEthernet4 ip address dhcp ip nat enable duplex auto speed auto ! interface Vlan1 ip address 192.168.1.x 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat enable ! interface Vlan2 ip address 192.168.0.x 255.255.255.0 ! ip forward-protocol nd ip http server ip http access-class 1 ip http authentication local ip http secure-server ! ! ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.x 1723 interface FastEthernet4 1723 ! ! access-list 1 permit 192.168.0.0 0.0.0.255 access-list 2 permit 192.168.1.0 0.0.0.255 ! ! ! ! control-plane ! ! banner motd Authorized Access only ! line con 0 exec-timeout 15 0 login authentication local_auth line aux 0 exec-timeout 15 0 login authentication local_auth line vty 0 4 access-class 2 in login authentication local_auth length 0 transport input all ! ! end UPDATE 16/12/2012: The only progress that I have been able to make on this issue is that I'm confident that the issue is caused by the GRE tunnels (which are required for the PPTP connection to complete) are being blocked. When attempting a connection, I can see in show ip nat nvi translations that both a TCP translation on 1723 is setup and also a GRE translation is setup also. I appear to be able to see GRE related packets on the LAN that the server is on, so I am lead to believe that the server is sending(?) GRE packets, however running Wireshark on a client PC when attempting a connection shows absolutely no GRE packets. Whilst there are no configuration directives in my config posted above (that I can pin point) which would specifically block them, it would appear that the GRE packets are not being allowed in/out of the router's firewall, even though a NAT translation entry is setup to the server's LAN address. Would anyone be able to provide me with some help to ensure that GRE packets are not blocked by the router's firewall, so that this can be ruled out as a possible issue please?

  Read the article

• How To Find Reasons of Why Site Goes Online/Offline

  - by HollerTrain

  Seems today a website I manage has been going online and offline throughout the entire day. I have no idea what is causing the issue so I am seeking guidance on where to start. It is a Wordpress based site. So here is what I DO know: I use a program that pings the server every minute and when the server is not responding me it emails me, so I can know exactly when the site is online and offline. The site between 8pm to 12pm 12.28, and around the 1a hour early morning 12.29 (New York City timezone, and all times below are in same timezone). At the time of the ups/downs I see a lot of strain on the memory usage. Look at the load average when the site is going online/offline (http://screencast.com/t/BRlfXkqrbJII). Then I ran this command to restart http (http://screencast.com/t/usVtYWZ2Qi) and the memory usage then goes down to this (http://screencast.com/t/VdTIy3bgZiQB). An hour after I restarted http, the site then went offline/online so restarting the http didn't do much help. When the site is going offline/online, I ran the top command and get this (http://screencast.com/t/zEwr7YQj3). Here is a top command when the site is at it's lowest (http://screencast.com/t/eaMfha9lbT - so this would be dubbged "normal"). Here is a bandwidth report (http://screencast.com/t/AS0h2CH1Gypq). The traffic doesn't seem to be that much (http://screencast.com/t/s7hrWNNic1K), but looking at my times the site is going up/down this may be one of the reasons? I have the dvp Nitro package at Media Temple (http://mediatemple.net/webhosting/nitro/). So at this point I would request some help in trying to figure out what the cause of this is, and how I can go about pinpointing this issue. ANY HELP is greatly appreciated.

  Read the article

• How to configure a trusted connection between IIS 7 and SQL Server 2005?

  - by user1180652

  How do configure a trusted connection between IIS 7 and SQL Server 2005? My webapp was working fine with Windows Authentication enabled in IIS. Now, in order to solve a problem, we need to use a trusted connection. Unfortunately, enabling the trusted connection in the web.config broke the webapp. Oddly enough, when I run this application with trusted connection from my local dev machine (using the Cassini web server) IIS (Windows Server 2008) is running on one machine. The database (SQL Server 2005 but could migrate to 2008) is running on another machine. We are on a Windows domain running AD. All traffic is within our own firewall - no public access. Beyond that, I can't provide much info but I can find it. We're very "compartmentalized" (we have server people, security people, oracle people, SQL Server people, etc.) Thanks! Update 02/14/2012 0902: The webapp is now functional (app no longer broken) but the main issue is still unresolved. Now I have the app's application pool running as a domain account with permissions on the SQL Server box and IIS box. We were using this account to run the application but, and here's the problem, we need to log the real user name that made a change. When using the service account, the name of that service account appeared in the audit tables, making the auditing quite useless. So, not I'm at least running again. The connection string in the web.config is using "Trusted_Connection=True", the appPool is using a domain account with access to both boxes, BUT when I make a change (logged in as me) the name of the service account (appPool identity) is still logged in the audit tables. I also manually granted full permissions to the service account on the webapp folder. What do I need to do in order to log my name, not the service account, in the audit tables? Everything I'm reading says I need to establish a trusted connection between the two servers.

  Read the article

• High CPU usage in my digitalocean droplet

  - by Ibrahim Azhar Armar

  I am experiencing high CPU usage here is the stats i got from server, the consumption after every restart in 15 minutes go upto 100%, what could go wrong? I have a wordpress copy installed on the server which does not have much traffic, here is the stats that i got from using top command in server. top - 11:46:02 up 12 min, 3 users, load average: 40.89, 16.03, 6.11 Tasks: 132 total, 41 running, 91 sleeping, 0 stopped, 0 zombie Cpu(s): 24.3%us, 61.5%sy, 0.0%ni, 0.0%id, 4.0%wa, 0.0%hi, 0.0%si, 10.2%st Mem: 2050896k total, 1988656k used, 62240k free, 284k buffers Swap: 0k total, 0k used, 0k free, 4712k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 31 root 20 0 0 0 0 R 39 0.0 1:35.53 kswapd0 899 root 20 0 15988 172 0 S 14 0.0 0:05.00 irqbalance 418 syslog 20 0 243m 600 0 S 13 0.0 0:06.85 rsyslogd 944 mysql 20 0 1320m 53m 0 S 12 2.7 0:21.15 mysqld 2357 root 20 0 17344 532 164 R 11 0.0 0:14.27 top 960 root 20 0 246m 3816 0 S 3 0.2 0:08.18 php5-fpm 2431 www-data 20 0 344m 64m 908 R 2 3.2 0:04.23 apache2 2435 www-data 20 0 304m 63m 836 R 2 3.2 0:03.43 apache2 2413 www-data 20 0 349m 63m 920 R 2 3.2 0:07.51 apache2 2465 www-data 20 0 349m 64m 944 R 2 3.2 0:05.04 apache2 2518 www-data 20 0 307m 41m 1204 R 2 2.1 0:01.37 apache2 2406 www-data 20 0 346m 56m 1144 R 2 2.8 0:03.76 apache2 2456 www-data 20 0 345m 55m 1184 R 2 2.8 0:02.67 apache2 2373 www-data 20 0 351m 63m 784 R 2 3.2 0:11.09 apache2 2439 www-data 20 0 306m 35m 916 R 2 1.8 0:02.51 apache2 2450 www-data 20 0 345m 55m 1088 R 2 2.8 0:02.96 apache2 2486 www-data 20 0 299m 10m 876 R 2 0.5 0:01.19 apache2 2523 www-data 20 0 300m 27m 796 R 2 1.4 0:00.99 apache2

  Read the article

• AWS VPC ELB vs. Custom Load Balancing

  - by CP510

  So I'm wondering if this is a good idea. I have a Amazon AWS VPC setup with a public and private subnets. So I all ready get the Internet Gateway and NAT. I was going to setup all my web servers (Apache2 isntances) and DB servers in the private subnet and use a Load Balancer/Reverse Proxy to pick up requests and send them into the private subnets cluster of servers. My question then, is Amazons ELB's a good use for these, or is it better to setup my own custom instance to handle the public requests and run them through the NAT using nginx or pound? I like the second option just for the sake of having a instance I can log into and check. As well as taking advantage of caching and fail2ban ddos prevention, as well as possibly using fail safes to redirect traffic. But I have no experience with their ELB's, so I thought I'd ask your opinions. Also, if you guys have an opinion on this as well, would using the second option allow me to only have 1 public IP address and be able to route SSH connections through port numbers to respective instances? Thanks in advance!

  Read the article

• VLAN Through Switch Doesn't Work

  - by vcsjones

  I have the following scenario: I have a Cisco Aironet 1040 access point. I have it configured with two SSIDs, each going to a different VLAN. So: SSID internal : VLAN 90 SSID guest : VLAN 70 On the router side, I have a Cisco RV220W (with the radios now turned off) and have setup VLANs with like VLAN IDs. VLAN 90 : 192.168.90.0/24 VLAN 70 : 192.168.70.0/24 As far as DHCP is concerned, each VLAN has a "DHCP Server" in the router's configuration: So with the access point connected directly to the router, everything works great. I connect to the internal network, and I get a 192.168.90.x address, and the guest network gets a 70.xxx address. Next I introduced a Cisco SG200-50 PoE switch between the router and the access point. The port is configured as a trunk port, so the VLAN tags should go right through the switch back to the router. However, when something is connected to the access point, nothing works. It isn't able to get an IP address, and manually assigning one doesn't seem to let any traffic route. Given that the access point works correctly when connected to the router directly, I believe the switch is misconfigured. What am I missing here? What can I use to better diagnose what the problem might be? It's small business equipment, so CLI access is not available. Below are screenshots of the switch's config. The access point is connected to GE2.

  Read the article

• How to use Cisco AnyConnect VPN Client?

  - by ktm5124

  I wrote a related question earlier, which is still unresolved. This question is much more specific. So I installed Cisco AnyConnect VPN Client on Snow Leopard. I connect to my work VPN. Once connected, I can't ping my work machine. I don't see any computers on the network. If the client were not running, I wouldn't believe myself to be connected to the VPN. Is there something that I am doing wrong? Do I have to route my network traffic through the tunnel manually? (ifconfig route comes to mind) Is the POST request that I am about to submit going to go through the tunnel created by my VPN? I guess the main question is: why do I feel so in the dark? Cisco says I am connected to my VPN, but for all I know it is invisible. N.B. I do have the up-to-date Cisco VPN Client: version 2.3.2016. I installed it about a week ago.

  Read the article

• apache performance timing out

  - by Mike

  Im running a webserver where I'm hosting about 6-7 websites. Most of these websites get their content from MySQL which is hosted on the same server. Traffic average per day is about 500-600 unique visitors, about 150K hits per week. But for some reason sometimes websites send a timeout, OR sometimes websites dont load all images. I know that I should perhaps separate static content from dynamic content, but for now I think that's not a possibility. I would appreciate any suggestions on how could I improve the performance of apache, so it doesn't keep timing out. Server is running on Sempron LE 1300; 2.3GHz,512K Cache 2GB RAM 10Mbps/1Mbps Services: MySQL, ProFTPD, Apache. Private + Shared = RAM used Program ---------------------------------------------------- 1.2 MiB + 54.0 KiB = 1.2 MiB proftpd 4.1 MiB + 23.0 KiB = 4.1 MiB munin-node 20.8 MiB + 120.5 KiB = 20.9 MiB mysqld 47.3 MiB + 9.9 MiB = 57.3 MiB apache2 (22) top: Mem: 2075356k total, 1826196k used, 249160k free, Timeout 35 KeepAlive On MaxKeepAliveRequests 300 KeepAliveTimeout 5 <IfModule mpm_prefork_module> StartServers 10 MinSpareServers 20 MaxSpareServers 20 MaxClients 60 MaxRequestsPerChild 1000 </IfModule> <IfModule mpm_worker_module> StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule>

  Read the article

• Issue with multiple bridging for KVM hosts

  - by Henry-Nicolas Tourneur

  I'm using KVM and libvirt on my host (Debian lenny) + 2 bridges per guest (one for mgmt, one for public traffic). That setup isn't stable at all, sometimes I can do pings to a management ip, sometimes not. I don't know if my bridging paramateres are correct, could you check ? or if there is anything wrong ... Please also note that interface on guest doesn't flap and that I got not logs on my host. Of course forwarding is enabled. iface eth3 inet manual auto bond0 iface bond0 inet manual slaves eth1 eth2 pre-up ip link set bond0 up down ip link set bond0 down auto br0 iface br0 inet static address 10.160.0.7 netmask 255.255.255.128 bridge_ports eth3 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br0:1 iface br0:1 inet static address 10.160.0.9 netmask 255.255.255.128 auto br0:2 iface br0:2 inet static address 10.160.0.10 netmask 255.255.255.128 auto br1 iface br1 inet static address 217.4.40.242 netmask 255.255.255.240 gateway 217.4.40.241 pre-up /etc/network/firewall start bridge_ports bond0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br1:1 iface br1:1 inet static address 217.4.40.252 netmask 255.255.255.240 auto br1:2 iface br1:2 inet static address 217.4.40.253 netmask 255.255.255.240

  Read the article

• Arch Linux drops me on my school network

  - by Kravlin

  I'm running a Lenovo X61 which i carry around my college for getting on the internet at various points in the day. The network has always been finicky but recently it's gotten worse. I'll connect using iwconfig, get an ip from dhcpcd and log in using vpnc to their system. Sometimes I'll stay connected for hours but most of the time within 30 seconds my network traffic will drop to zero and i'll be unable to do anything. My computer still belives it's connected, however to try again i need to put my wireless interface down, put it back up and try again. It's gotten so bad that i've got a window on my computer pinging yahoo or google constantly in order to know if i'm still able to get online. I know other people who have used Arch Linux that don't have the same problems as well as people who use Ubuntu who haven't had any problems either. It seems like my computer is a special case. Does anyone have any suggestions on how to fix it? dmesg doesn't show anything out of the ordinary going on and i don't know where else to look for errors or other things to try. Edit: this doesn't happen on my home network. It's a problem that only happens at school.

  Read the article

• Any non-custom way to manage iptables with fail2ban and libvirt+kvm?

  - by Peter Hansen

  I have an Ubuntu 9.04 server running libvirt/kvm and fail2ban (for SSH attacks). Both libvirt and fail2ban integrate with iptables in different ways. Libvirt uses (I think) some XML config and during startup (?) configures forwarding to the VM subnet. Fail2ban installs a custom chain (probably at init) and periodically modifies it to ban/unban probable attackers. I also need to install my own rules to forward various ports to servers running in VMs and on other machines, and set up rudimentary security (e.g. drop all INPUT traffic except the few ports I want open), and of course I'd like the ability to add/remove rules safely without restarting. It seems to me iptables is a powerful tool that's sorely lacking some sort of standardized way of juggling all this stuff. Every project, and every sysadmin, seems to do it differently! (And I think there's lots of "cargo cult" admin going on here, with people cloning crude approaches like "use iptables-save like so".) Short of figuring out the gory details of exactly how both of these (and potentially other) tools manipulate the netfilter tables, and developing my own scripts or just manually executing iptables commands, is there any way to safely work with iptables while not breaking the functionality of these other tools? Any nascent standards or projects defined to bring sanity to this area? Even a helpful web page I missed that might cover at least these two packages together?

  Read the article

• Enabling NAT forwarding using a second WAN interface and a second gateway on ubuntu

  - by nixnotwin

  I have 3 interfaces: eth0 192.168.0.50/24 eth1 10.0.0.200/24 eth2 225.228.123.211 The default gateway is 192.168.0.1 which I want to keep as it is in the changes I want to make. I want to masquerade eth1 10.0.0.200/24 and enable NAT forwarding to eth2. So I have done this: ip route add 225.228.123.208/29 dev eth2 src 225.228.123.211 table t1 ip route add default via 225.228.123.209 dev eth2 table t1 ip rule add from 225.228.123.211 table t1 ip rule add to 225.228.123.211 table t1 Now I can receive ping replies from any internet host if I did: ping -I eth2 8.8.8.8 To enable NAT forwarding I did this: sudo iptables -A FORWARD -o eth2 -i eth1 -s 10.0.0.0/24 -m conntrack --ctstate NEW -j ACCEPT sudo iptables -A FORWARD -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT sudo iptables -t nat -A POSTROUTING -o eth1 -j MASQUERADE But it isn't working. To test I used a client pc and put it on 10.0.0.0/24 network and gateway was set as 10.0.0.200. I want to have 192.168.0.1 as default gateway. And the traffic that comes in via eth1 10.0.0.200/24 should be forwarded to eth2 225.228.123.211. I have enabled forwarding on ubuntua also.

  Read the article

• Simple Linux program that takes any HTTP/HTTPS request and returns a single page?

  - by ultrasawblade

  I have a Linux box operating as router. There's a NIC that's connected to the internet (WAN), a NIC connected to an 8-port GbE switch (LAN), and a NIC connected to a Linksys wireless N-router (WLAN). Routing between everything is working perfectly. I have security completely disabled on the wireless router, but the WLAN NIC is firewalled such that it will only accept DNS queries and PPTP VPN connections. Currently HTTP/HTTPS traffic and everything else is blocked. I would like to run something that listens on port 80/443 of the WLAN NIC, and, for non VPN'ed connections, given any HTTP/HTTPS request it will return a single webpage saying "Unauthenticated" and explain how to sign into the VPN. A transparent proxy seems to be what I need, but my searches all seem to direct me to Squid, which is already running on my server and seems overkill for this simple task. Is there a simpler, lightweight program out there that does just this or should I just suck it up and run two instances of Squid (or figure out how to configure it)? Or, is this entire VPN thing I'm doing complete nonsense and I should just enable encryption on the wireless router?

  Read the article

• Why would my wireless cut in and out every minute or so?

  - by Strilanc

  I've been having problems with my wireless. I moved to a new apartment, and the wireless seems incredibly unreliable. Sometimes it will be stable for hours until, all of a sudden, it starts cutting in and out. I'll get 30-90 seconds of normal behavior, then 5-30 seconds of nothing, then repeat. Sometimes the connection will stop working entirely, until I power-cycle the router. It is extremely, extremely annoying. Surfing the web isn't too bad, assuming you can stand the random 5-30 second waits. But some connections are sensitive enough to timeout, and it certainly makes multiplayer games unplayable. Facts: I confirmed the problem using ping google.com -t. I get normal traffic, interspersed with bursts of "Request timed out.". I've never had this problem before with this laptop. I didn't bring my own router or modem to the apartment. I'm using what the old tenant had. Hooking directly to the modem via an ethernet cable results in a stable connection. Temporarily cutting power to the router sometimes fixes the problem. Sometimes it doesn't. I reset the router, but the problem remained. Apparently the previous tenant had issues with the internet, but I don't know what they were specifically. The router is a D-Link DIR-615, and their tech support is useless.

  Read the article

• IPtables: DNAT not working

  - by GetFree

  In a CentOS server I have, I want to forward port 8080 to a third-party webserver. So I added this rule: iptables -t nat -A PREROUTING -p tcp --dport 8080 -j DNAT --to-destination thirdparty_server_ip:80 But it doesn't seem to work. In an effort to debug the process, I added these two LOG rules: iptables -t mangle -A PREROUTING -p tcp --src my_laptop_ip --dport ! 22 -j LOG --log-level warning --log-prefix "[_REQUEST_COMING_FROM_CLIENT_] " iptables -t nat -A POSTROUTING -p tcp --dst thirdparty_server_ip -j LOG --log-level warning --log-prefix "[_REQUEST_BEING_FORWARDED_] " (the --dport ! 22 part is there just to filter out the SSH traffic so that my log file doesn't get flooded) According to this page the mangle/PREROUTING chain is the first one to process incomming packets and the nat/POSTROUTING chain is the last one to process outgoing packets. And since the nat/PREROUTING chain comes in the middle of the other two, the three rules should do this: the rule in mangle/PREROUTING logs the incomming packets the rule in nat/PREROUTING modifies the packets (it changes the dest IP and port) the rule in nat/POSTROUTING logs the modified packets about to be forwarded Although the first rule does log incomming packets comming from my laptop, the third rule doesn't log the packets which are supposed to be modified by the second rule. It does log, however, packets that are produced in the server, hence I know the two LOG rules are working properly. Why are the packets not being forwarded, or at least why are they not being logged by the third rule? PS: there are no more rules than those three. All other chains in all tables are empty and with policy ACCEPT.

  Read the article

• Bandwidth Suggestion

  - by Campo

  I have been asked to analyze the bandwidth usage of a company and make a recommendation for upgrading their Internet connection(s). Here is the layout 3 DLS lines so it is 3x(6 Down, 1 Up Each) into a load balancer out to the office's network. 30 VOIP phones run on a T1 (1.5 Down, 1.5 Up) The users at the company are heavily uploading. It is my suspicion that the issue in slowdown is being cause by multiple people uploading and others not being able to get requests out for even simple http requests. My initial idea is to get them a fiber line with a 10 down and 10 up. What do others think on this plan? Will that be enough to host their network traffic? What do I do about the VOIP line afterward? The fiber is expensive and I know the T1 does a great job for their VOIP so I do not want to suggest a DSL line because I know it may not be sufficient. I would also like to save them some money if I can. Maybe even get a faster fiber line and forgo the T1. Though I know their load balance/switch can only handle 20MB/S throughput. Looking for some confirmation/suggestions on my plan. I am planning on going in to get some real diagnostic numbers. Any suggestions on software to use for that? Preferably Windows software.

  Read the article

• How to Load Balance 2 Internet Connections on a Windows 7 machine?

  - by Jimmy Chandra

  It's sort of related to this particular question, but that one is on Mac. I am looking for similar solution on Windows 7. I have 2 network connections: (Connection A) Wireless terminal connecting to ISP A (3G / EVDO internet provider) (Connection B) Broadband wired connection connecting to ISP B (Cable internet provider) Both has access to the internet. When I try connecting to a website and checking the networking tab on my Task Manager, I only see the network traffic being routed to only Connection A. Is there a way to make the computer to utilize both network (in a sense using all the bandwidth available from both the Cable ISP and the 3G / EVDO ISP) at the same time? If so, what do I need to do to set this up ... on Windows 7? Here is a bit more info on my network connections (ipconfig /all): PPP adapter Wireless Terminal: IPv4: aa.bb.ccc.ddd(preferred) Subnet mask: 255.255.255.255 Default Gateway: 0.0.0.0 DNS: aa.ee.f.ggg aa.ee.f.hhh Primary Wins: jjj.ii.k.l Secondary Wins: jjj.ii.k.m Ethernet adapter LAN: IPv4: 192.168.1.100 (connected to a router by wired that itself connect to a cable modem) subnet mask: 255.255.255.0 Default gateway: 192.168.1.1 (the wireless router) DHCP: 192.168.1.1 (the wireless router) DNS: xxx.yy.zz.ww rr.sss.t.uuu For my own privacy, I don't believe the actual number matters, the patterns are representative of the ip numbering scheme...

  Read the article

• When should NTPd broadcast/broadcastclient be used instead of client/server or peer modes?

  - by Luke404

  The NTP deamon if often used in its simplest mode, which is client/server: you specify one or more server directives in your ntp.conf and your clients will use those servers. In addition to that, when you run your own NTP servers, it is good practice to peer them together, so if one of them looses connectivity to its upstream servers, it will get time from its peers. But NTPd can also work with broadcast and/or multicast distribution of time data, with the documentation stating: broadcast and multicast modes are intended for configurations involving one or a few servers and a possibly very large client population The documentation also says elsewhere: It is possible and frequently useful to configure a host as both broadcast client and broadcast server. A number of hosts configured this way and sharing a common broadcast address will automatically organize themselves in an optimum configuration based on stratum and synchronization distance. I can see one obvious administrative benefit: you don't have to manually specify and update your list of NTP servers in the clients ntp.conf, so to me it looks tempting to use broadcast mode even for a small client population (say 5+ clients with 3~4 servers). I expect network traffic to be a little higher with broadcasts instead of client/server associations, but given the usual gigabit ethernet LAN the impact should be negligible unless you have a very very large number of hosts in the same broadcast domain. At the end of the day, when should broadcast mode be used or avoided? Are there pros and cons I haven't seen?

  Read the article

• Homebrew large data cluster access for 2 user levels?

  - by Yegor

  The title probably makes little sense, so here is an example. I have a file hosting site, that serves a large amount of semi-randomly accessed files. The setup is as follows: High horsepower front-end +DB server that also does encoding for files that need encoding Fresh file server, which stores newly uploaded content, thats probably (and usually) rapidly accessible, which has 500GB of raided SSD storage, that can push over 3GBit of traffic. 3 cheap node servers, containing 2 x 750GB SATA drives in raid1, where files older than 2 weeks are archived, from the SSD server (mentioned above). Files on each server are accessed via subdomains (via modsec) in a straight forward fashion (server1.domain.com, server2.domain.com, etc) Where I have the problem is this. I introduced a "premium" service where people pay a small fee every month, and get ad-free, quick accesses to stuff on the site. Once they are logged in, they access same files via premium.server1.domain.com via a different modsec script, with a different pass phrase. That all works fine and dandy.... except the cheap node servers are all IO bound, so accessing the files on them via a different, unsaturated network makes no difference, since it cannot read off the drive fast enough. What would be a good way to make files on the site be accessible via 2 different network routes, 1 of which will be saturated (the "free network") while all other files are on an un-saturated "premium" network?

  Read the article

• SSL connection hangs as client hello (curl, openssl client, apt-get, wget, everything)

  - by Niklas B

  Hi, I've run into a problem on my Debian VPS (a xen domU) regarding SSL. Namely almost all SSL connections hangs at client hello. For example: # curl -vI https://graph.facebook.com About to connect() to graph.facebook.com port 443 (#0) Trying 66.220.146.48... connected Connected to graph.facebook.com (66.220.146.48) port 443 (#0) successfully set certificate verify locations: CAfile: none CApath: /etc/ssl/certs SSLv3, TLS handshake, Client hello (1): It's the same when using the openssl client. However, some of the SSL traffic works (for example https://www.nordea.se). Server #uname -a Linux server.com 2.6.26-1-xen-amd64 #1 SMP Fri Mar 13 21:39:38 UTC 2009 x86_64 GNU/Linux It does however work on my Dom 0 (the main xen host). Apt-get I can't even run apt-get update with the debian security sources (hangs on reading headers) Open SSL At the begining I thought I had an old openssl client (0.9.8o-4) since I appeared to have a newer on the Dom 0 (0.9.8g-15+lenny8) but doing a manuanl update on the openssl deb didn't help. Open SSL Client This is the full output of when the openssl client hangs: http://pastebin.com/PAjwMap9 Closing thoughts I've Googled the crap out of this, and I'm not getting any further. I've seen problems with curl, apt-get etc. but they are all specific relating to the very application - not general for the system. Any thoughts?

  Read the article

< Previous Page | 524 525 526 527 528 529 530 531 532 533 534 535  | Next Page >