Search Results

Search found 32568 results on 1303 pages for 'linux pwns mac'.

Page 529/1303 | < Previous Page | 525 526 527 528 529 530 531 532 533 534 535 536  | Next Page >

  • iptables question

    - by RubyFreak
    i have a small network, with one valid IP and a firewall with 3 network interfaces (LAN, WAN, DMZ). I want to enable PAT on this valid IP to redirect http traffic to a server in my DMZ. (done) I want to enable MASQ on this ip from traffic that comes from my LAN (done) I want from my LAN as well to access my http server at DMZ. (partially) Question: in the above scenario, i cannot from my LAN, to access my http server in the DMZ, since it has the IP used by the MASQ (the only valid ip that i have). What would be the best option to solve this problem? network interfaces: eth0 (WAN) eth1 (DMZ) eth2 (LAN) /sbin/iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE /sbin/iptables -A FORWARD --o eth1 -d 2.2.2.2 -p tcp --dport 80 -j ACCEPT /sbin/iptables -t nat -A PREROUTING -i eth0 -d 1.1.1.1 -p tcp --dport 80 -j DNAT --to 2.2.2.2 /sbin/iptables -A FORWARD -i eth0 -o eth1 -m state --state RELATED,ESTABLISHED -j ACCEPT /sbin/iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT /sbin/iptables -A FORWARD -i eth2 -o eth0 -j ACCEPT

    Read the article

  • How to migrate KVM based VMs running in LVM setup to Vmdk images

    - by Bond
    I am using KVM on Ubuntu Server 10.04. and Virtual Machines are running on it in LVM. I have to migrate some of them to Vmware server.How can I achieve this? I searched and came across some links but they all talked converting vmdk images to qcow or so.In this case I have OS in LVM. I also looked at man page of qemu-img and as I understand it should do what I am asking in this thread. But how exactly should I proceed in this case.Since it is not a file based image (OS running in an LVM which has filesystem in that LVM). So I am not able to understand what should I be doing to achieve the same. Can I achieve the above with snapshots of LVMs rather than shutting down the VM itself.

    Read the article

  • Route return traffic to correct gateway depending on service

    - by Marnix van Valen
    On my office network I have two internet connections and one CentOS server running a website (HTTPS on port 443). The website should be publicly accessible through the public IP of the first internet connection (ISP-1). The other internet connection, ISP-2, id the default gateway on the network. Both internet connections have routers (the household-kind) with NAT, SPI firewalls etc. The router on ISP-2 is a Netgear WNDR3700 (aka N600) with original firmware. The problem is that the website is unreachable. Looks like incoming traffic on ISP-1 will reach the server but the returning traffic is routed through ISP-2, effectively making the site unreachable. As far as I can tell I can't do port based routing on the WNDR3700. What are my options to make this work? I've been looking at implementing an iptables / routing based solution on the server itself but haven't been able to make that work. Update: Note that the server has one network interface connecting it to both routers.

    Read the article

  • use network drives as mount points during installation?

    - by ajsie
    is it possible to use network storage locations as mount points during installation? cause i want to separate system (ubuntu) with data (personal files). eg. if i have 5 computers i don't want to recreate /home/david 5 times. so i want to mount networkdrive/home to /home in local ubuntu server. so ALL users home folders could be used and maybe also networkdrive/projects to /projects. in that way its ok if i by accident repartitioned the local ubuntu server cause all data is not there on that server, but in the data server. is separating "data" from "logic" good in this case? and is it possible? what protocol should i use for the mapping over internet? (maybe the server is in Sweden, and the data is in Norway). thanks.

    Read the article

  • Default permission for newly-created files/folders using ACLs not respected by commands like "unzip"

    - by Ngoc Pham
    I am having trouble with setting up a system for multiple users accessing the same set of files. I've read tuts and docs around and played with ACLs but haven't succeeded yet. MY SCENARIO: Have multiple users, for example, user1 and user2, which is belong to a group called sharedusers. They must have all WRITE permission to a same set of files and directories, say underlying in /userdata/sharing/. I have the folder's group set to sharedusers and SGID to have all newly created files/dirs inside set to same group. ubuntu@home:/userdata$ ll drwxr-sr-x 2 ubuntu sharedusers 4096 Nov 24 03:51 sharing/ I set ACLs for this directory so I can have permission of sub dirs/files inheritted from its parents. ubuntu@home:/userdata$ setfacl -m group:sharedusers:rwx sharing/ ubuntu@home:/userdata$ setfacl -d -m group:sharedusers:rwx sharing/ Here's what I've got: ubuntu@home:/userdata$ getfacl sharing/ # file: sharing/ # owner: ubuntu # group: sharedusers # flags: -s- user::rwx group::r-x group:sharedusers:rwx mask::rwx other::r-x default:user::rwx default:group::r-x default:group:sharedusers:rwx default:mask::rwx default:other::r-x Seems okay as when I create new folder with new files inside and the permission is correct. ubuntu@home:/userdata/sharing$ mkdir a && cd a ubuntu@home:/userdata/sharing/a$ touch a_test ubuntu@home:/userdata/sharing/a$ getfacl a_test # file: a_test # owner: ubuntu # group: sharedusers user::rw- group::r-x #effective:r-- group:sharedusers:rwx #effective:rw- mask::rw- other::r-- As you can see, the sharedusers group has effective permission rw-. HOWEVER, if I have a zip file, and use unzip -q command to unzip the file inside the folder sharing, the extracted folders don't have group write permisison. Therefore, the users from group sharedusers cannot modify files under those extracted folders. ubuntu@home:/userdata/sharing$ unzip -q Joomla_3.0.2-Stable-Full_Package.zip ubuntu@home:/userdata/sharing$ ll drwxrwsr-x+ 2 ubuntu sharedusers 4096 Nov 24 04:00 a/ drwxr-xr-x+ 10 ubuntu sharedusers 4096 Nov 7 01:52 administrator/ drwxr-xr-x+ 13 ubuntu sharedusers 4096 Nov 7 01:52 components/ You an spot the difference in permissions between folder a (created before) and folder administrator extracted by unzip. And the ACLs of a files inside administrator: ubuntu@home:/userdata/sharing$ getfacl administrator/index.php # file: administrator/index.php # owner: ubuntu # group: ubuntu user::rw- group::r-x #effective:r-- group:sharedusers:rwx #effective:r-- mask::r-- other::r-- It also has ubuntu group, not sharedusers group as expected. Could someone please explain the problem and give me advice? Thank you in advance!

    Read the article

  • Limiting Failed SSH Logins

    - by nitins
    I would like to limit failure retries on my Fedora machine to 5. I think I can accomplish it with PAM. But was unable to to do this. I have referred to this article to do this http://www.puschitz.com/SecuringLinux.shtml Please provide suggestions

    Read the article

  • SELinux - Allow multiple services access to same /home/dir

    - by Mike Purcell
    I currently have SELinux enabled and have been able to configure apache to allow access to /home/src/web with a chcon command granting the 'httpd_sys_content_t' type. But now I am trying to serve the rsyslogd.conf file from the same directory, but every time I start rsyslogd I see an entry in my audit log saying that rsyslogd was denied access. My question is, is it possible to grant two applications the ability to access the same directory, while still keeping SELinux enabled? Current perms on /home/src: drwxr-xr-x. src src unconfined_u:object_r:httpd_sys_content_t:s0 src Audit log message: type=AVC msg=audit(1349113476.272:1154): avc: denied { search } for pid=9975 comm="rsyslogd" name="/" dev=dm-2 ino=2 scontext=unconfined_u:system_r:syslogd_t:s0 tcontext=system_u:object_r:home_root_t:s0 tclass=dir type=SYSCALL msg=audit(1349113476.272:1154): arch=c000003e syscall=2 success=no exit=-13 a0=7f9ef0c027f5 a1=0 a2=1b6 a3=0 items=0 ppid=9974 pid=9975 auid=500 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=30 comm="rsyslogd" exe="/sbin/rsyslogd" subj=unconfined_u:system_r:syslogd_t:s0 key=(null) -- Edit -- Came across this post, which is sort of what I am trying to accomplish. However when I viewed the list of allowed sebool params, the only relating to syslog was: syslogd_disable_trans (SELinux Service Protection), seems like I can maintain the current SELinux 'type' on the /home/src/ dir, but set the bool on syslogd_disable_trans to false. I wonder if there is a better approach?

    Read the article

  • Re-sync deleted files from rsync

    - by hfranco
    I need to recover files that have been deleted. My scenario: I have a rsync script that runs at 9PM and mirrors everything from server1 directory to another directory on backup server2. A couple of files have been accidentally deleted from server1. How do I recover those files from server1 with rsync?

    Read the article

  • Where is the xorg.conf file in Karmic Koala (Ubuntu 9.10) ?

    - by jfmessier
    I am trying to change this xorg.conf file that I used to modify under Ubuntu 9.04, so it can have the higher resolutions of my monitor. Under 9.04, the monitor was unknown, and I had to key in all resolutions in the file, and although it is found under 9.10, 9.10 does not have the highest resolution that My monitor can sustain. How can I change such setting ? Is xorg.conf moved, or replaced ? Merci :-) JF

    Read the article

  • How can I remove OLD history from Google Chrome?

    - by Norman Ramsey
    I'm working on a laptop with a modest hard drive, and 500MB is taken up with Google Chrome "History Index" and "Thumbnails" files. Some of these files are a year old. Chrome offers me the option to remove recent history, but I want the opposite: I want to remove old history. (Ideally I would remove the least recently used history information, but I don't expect to be able to do that.) Anyone have any ideas? I'm running the standard Debian google-chrome-beta package.

    Read the article

  • Debian Testing installs Iceweasel ESR (severely outdated)?

    - by Lucas Phillips
    I just reinstalled Debian Testing, and for some reason, instead of Iceweasel 25, I have 17. The installed and candidate versions are both 17.0.9esr-1~deb7u1. apt-get update && apt-get upgrade does nothing, and it seems that version 17 is the latest for this install. I was on Debian Testing before, and Iceweasel was at the latest version. Even Debian Stable had an Iceweasel version 20. Why would it be trying to install ESR now?

    Read the article

  • Using nawk, how to print the first names for all those in the 916 area code? [closed]

    - by Steve
    Possible Duplicate: Using nawk, how to print all first names containing four characters? Using nawk, how to print the first names for all those in the 916 area code? I've tried nawk ‘$3 ~ /(916)/{print $1}’ inputfile but didn' work. Jody Savage:(206) 548-1278:15:188:150 Guy Quigley:(916) 343-6410:250:100:175 Dan Savage:(406) 298-7744:450:300:275 Nancy McNeil:(206) 548-1278:250:80:75 John Goldenrod:(916) 348-4278:250:100:175 Chet Main:(510) 548-5258:50:95:135

    Read the article

  • How can I recover an ext4 filesystem corrupted after a fsck?

    - by Regan
    I have an ext4 filesystem on luks over software raid5. The filesystem was operating "just fine" for several years when I was beginning to run out of space. I had a 9T volume on 6x2T drives. I began upgrading to 3T drives by doing the mdadm fail, remove, add, rebuild, repeat process until I had a larger array. I then grew the luks container, and then when I unmounted and tried to resize2fs I was given the message the filesystem was dirty and needed e2fsck. Without thinking I just did e2fsck -y /dev/mapper/candybox and it began spewing all kinds of inode being removed type messages (can't remember exactly) I killed e2fsck and tried to remount the filesystem to backup data I was concerned about. When trying to mount at this point I get: # mount /dev/mapper/candybox /candybox mount: wrong fs type, bad option, bad superblock on /dev/mapper/candybox, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Looking back at my older logs I noticed the filesystem was giving this error each time the machine booted: kernel: [79137.275531] EXT4-fs (dm-2): warning: mounting fs with errors, running e2fsck is recommended So shame on me for not paying attention :( I then tried to mount using every backup superblock (one after another) and each attempt left this in my log: EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 0 failed (26534!=65440) EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 1 failed (38021!=36729) EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 2 failed (18336!=39845) ... EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 11911 failed (28743!=44098) BUG: soft lockup - CPU#0 stuck for 23s! [mount:2939] Attempts to restart e2fsck results in: # e2fsck /dev/mapper/candybox e2fsck 1.41.14 (22-Dec-2010) e2fsck: Group descriptors look bad... trying backup blocks... candy: recovering journal e2fsck: unable to set superblock flags on candy At this point, I decided it best to order some more drives and make an image using ddrescue Now two weeks later I have an image of the luks partition in a .img file. # ls -lh total 14T -rw-r--r-- 1 root root 14T Oct 25 01:57 candybox.img -rw-r--r-- 1 root root 271 Oct 20 14:32 candybox.logfile After numerous attempts using everything I could find online I could not coerce e2fsck to do anything on the image, so I used mkfs.ext4 -L candy candybox.img -m 0 -S and I was able to mount the dirty filesystem readonly without the journal and recover 960G of data. It gave all kinds of errors of various directories not existing and so forth but I was able to get some stuff. Which gave me some hope! I then ran e2fsck again and it had to recreate the root inode and gave a massive list of correcting group counts, I accepted the root inode creation and said no to everything else, leaving a completely empty filesystem. Re-ran again and said yes to all questions with the same result but now a "clean" but empty filesystem. extundelete gives me 0 recoverable inodes found. And now I'm stuck again, I can't come up with any other methods other than dropping to something like photorec which will give me an absolute mess with how large the filesystem was. I'm willing to re-copy the image from the original array and start over, if I can get any suggestions or ideas on a way to get more of my files back. I wish I could give more detailed logs of the commands that have run, but the output is long scrolled passed except for what gets logged to syslog and my memory is not as detailed due to the timeframe this has occurred over. Any help is greatly appreciated!

    Read the article

  • Configuring sendmail to forward mail for a specific domain to a specific mail server without using M

    - by aHunter
    I am new to sendmail and would like to configure sendmail to forward all mail for a specific email address to another internal mail server. I need it to ignore the MX records and only send it to the server I specify but am not sure which files to edit or how to configure the sendmail config. Is it sufficient to add the server to the /etc/hosts and the /etc/mail/local-host-names files? Thanks in advance.

    Read the article

  • How to delete files quicker than rm -rf?

    - by Byakugan
    Is there any way how to delete folder/files quicker than with command rm -rf? It seems my disc is filled with bilions of files (sessions of php5) which were not deleted in cron so I need to delete them manually but it takes hours and it is still not helping reducing the amount. Thank you. My command: rm -rf /var/lib/php5/* Tried also these commands: find /var/lib/php5 -name "sess_*" -exec rm {} \; And perl -e 'chdir "/var/lib/php5/" or die; opendir D, "."; while ($n = readdir D) { unlink $n }'

    Read the article

  • Sending mail results in "Sender address rejected: Domain not found"

    - by user1281413
    The setup: WHM/CPanel CentOS 5 server running Exim and Courier for mail services, and BIND for domain name services. I recently moved servers. The old server was running a HIGHLY similar configuration, and all accounts were ported via WHM. However, the server is unable to send, and sometimes receive email. Errors I am seeing (when I do get an error mail back) state: 450 4.1.8 : Sender address rejected: Domain not found Edit for clarity: this is the error response from remote mail servers. Numerous independent mail servers come back with the same error. (Email address is merely one valid example) My first instinct of course was to check the domain records. However, k-t.org appears to have a valid record (including an MX record), even after running it through domain checks on a completely different server elsewhere and online. Note that the issue appears to happen with all the domains hosted on the server, not just k-t.org I have also ensured that a PTR was created. My Googling has only lead me to people who had fairly basic DNS mistakes, but either I'm blind/dumb (possible, DNS is not my strong suite), or it's something that is a bit more archaic. I've run out of ideas, and I can't seem to find anything that could explain why servers are unable to resolve the domains. There doesn't seem to be anything missing or incorrect.

    Read the article

  • dhclient append settings from multiple DHCP servers

    - by Brian
    I have a server with two interfaces connected to two separate networks, using DHCP for both. When dhclient is writing /etc/resolv.conf, I would like it to append settings that aren't already there. For instance, if I receive from one DHCP server: nameserver 10.0.0.1 search one.mydomain.com and from another: nameserver 10.1.1.254 search two.mydomain.com Then resolv.conf should look like this: search one.mydomain.com two.mydomain.com nameserver 10.0.0.1 nameserver 10.1.1.254 At the moment, it seems the last dhclient overwrites whatever was there. I know I can preconfigure settings in dhclient.conf using supercede or append, but then I have to hard-code the values. I've scoured the man page for dhclient, but it seems like dhclient prefers to work alone (i.e. not in conjunction with any other dhclients)...or am I missing something?

    Read the article

  • Add user in CentOS 5

    - by Ron
    I created a new user in my CentOS web server with useradd. Added a password with passwd. But I can't log in with the user via SSH. I keep getting 'access denied'. I checked to make sure that the password was assigned and that the account is active. /var/log/secure shows the following error: Aug 13 03:41:40 server1 su: pam_unix(su:auth): authentication failure; logname= uid=500 euid=0 tty=pts/0 ruser=rwade rhost= user=root Please help, Thanks Thanks for the responses so far: I should add that it is a VPS on a remote computer, fresh out of the box. I can log in as the root user quite fine. I can also su to the new user, but I cannot log in as the new user. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

    Read the article

  • Name of log file where boot process is logged

    - by ant2009
    Hello, CentOS 5.3 After booting up. I am wondering what is the name of the log file that contains if all services where successfully loaded or not? For example when computer boots you get a list of start services and they can be OK or FAILED. Is there a log file where this information is kept? I had a look in the following directory /var/log/ but not sure which one will contain the informaiton that I need. Many thanks for any advice,

    Read the article

  • tmpreaper, --protect and a non-root user

    - by nsg
    Hi, I'm a little confused. I have a download directory that I want to remove all files older then 30 days with tmpreaper. Just one problem, the directory in question is a separate partition with a lost+found directory, of course I need to keep it so I added --protect 'lost+found', the problem is that tmpreaper outputs: error: chdir() to directory 'lost+found' (inode 11) failed: Permission denied (PID 30604) Back from recursing down `lost+found'. Entry matching `--protect' pattern skipped. `lost+found' I have tried with other pattern like lost* and so on... I'm running tmpreaper as a non-root user because there is no reason for superuser privileges because I own all files (except lost+found). Are I'm forced to run tmpreaper as root? Or are my shell-skills not as good as I thought? I guess the problem is: tmpreaper will chdir(2) into each of the directories you've specified for cleanup, and check for files matching the <shell_pattern> there. It then builds a list of them, and uses that to protect them from removal. Any thought and/or advice? Edit: The command I'm trying to run is something like $ /usr/sbin/tmpreaper -t --protect 'lost+found' 30d /mydir 1> /dev/null error: chdir() to directory `lost+found' (inode 11) failed: Permission denied Edit 2: I read the source code for tmpreaper-1.6.13 and found this if (safe_chdir (dirname)) exit(1); and if (chdir (dirname)) { message (LOG_ERROR, "chdir() to directory `%s' (inode %lu) failed: %s\n", dirname, (u_long) sb1.st_ino, strerror (errno)); return 1; } So it seems tmpreaper needs to be able to chdir in to all directories, ignored or not. I see two options left Run tmpreaper as root Move the download directory Find a alternative tool (tmpwatch?) I will give it some more research before i make a choice.

    Read the article

  • What is the most secure way to allow a user read access to a log file?

    - by gAMBOOKa
    My application requires read access to /var/log/messages, which belongs to user and group root. What is the minimal exposure level required on /var/log/messages so my application can read it? Presently, my plan is to change the group ownership of /var/log/messages to a new group, and add root and my application user to it, but this would also give the application write privileges to /var/log/messages. OS: Centos 5.5

    Read the article

  • How to run Firefox jailed without serious performance loss?

    - by Vi
    My Firefox configuration is tricky: Firefox runs at separate restricted user account which cannot connect to main X server. Firefox uses Xvfb (virtual "headless" X server) as X server. x11vnc is running on that Xvfb. On the main X server there is vncviewer running that connect to this x11vnc On powerful laptop (Acer Extensa 5220) it seems to work more or less well, but on "Acer Aspire One" netbook it is slowish (on a background that firefox is loaded with lots of extensions). How to optimise this scheme? Requirements: Browser cannot connect to main X server. Browser should be in chroot jail (no "suid" scripts, readonly for many things) Browser should have a lot of features (like in AutoPager, NoScript, WoT, AdBlockPlus)

    Read the article

< Previous Page | 525 526 527 528 529 530 531 532 533 534 535 536  | Next Page >