Search Results

Search found 9088 results on 364 pages for 'after power failure'.

Page 53/364 | < Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >

• Mainboard shuts itself off after half a second or so

  - by heishe

  Here's the problem: When I start the PC, the mainboard powers up, then stays that way maybe 0.2-0.5 seconds, and then shuts off again. I say mainboard, and not PC, because I removed all the parts from the system and disconnected everything but the mainboard power supply (the broad 12 pin thingy). When I have the other parts (cpu, graphics card, ram, etc.) installed and connected, the basic behaviour stays the same, but now the mainboard runs for about 6 or 7 seconds (this is a guess) before shutting off. This all started when my monitor wouldn't receive a video signal today, without giving POSTs, so I took the graphics card and the RAM out to see if it changes anything. It didn't, except that from that point on the mainboard would start to have this behavior where it just stays on for a very short time and then shuts off again. I already tested it with a backup PSU - same behavior. What could this be? I'm thinking it can't be on a physical level (transistors burned through or something like that), since then the mainboard either shouldn't start at all or it should detect hardware failures in non-essential parts of the syste and start beeping. Sorry, I forgot to mention. It's an MSI P67A-C43. I already checked the capacitors if someone popped, but I can't find anything. I also tried resetting the cmos, but that didn't change anything.

  Read the article

• vmdk Recovery after migration from 3.5 to 4 and fallback tentative.

  - by olgirard

  Hy, I've tryed to migrate some VM from my 3.5i environment to a brand new vSphere 4.0 U1. The two platforms are running simultaneously, sharing the same SAN. I Migrate my VM by stopping it, unregistering in vcenter (esx ver. 3.5, i call it esx3), register in vSphere (esx ver. 4, i call it esx4), and migrate upgrade virtual hardware before powering it up (First mistake). vMotion was enabled on esx4, seem to be a second mistake. After a day or so, i encountred problems joigning the esx server (esx4) and decided to unregister my server for esx4 and fallback to esx3. esx3 refused to boot, i supposed this was due to virtual hardware in Version 7 so i recreated a new VM pointing to the vmdk of the old VM. Everithing seemed fine until i log into the server and discover that i was running on the original disk ith every snapshots ignored even those created on esx3. I tried to reboot VM on esx4 but VM doesn't power up because "The parent virtual disk has been modified since the child was created". I've got a copy of a later state of the drive but generated between two snapshots (ovf generated with canverter standalone) as a backup. Do i have a chance to recover at least some files on the virtual drive or (as i tink) all is played, i've done enought mistakes for this time. Thanks for your help.

  Read the article

• Single computer on network cannot connect to internet.

  - by user34630

  Hi All, I hope you can help me out! :) I have 3 computers and one device (Xbox) on my home network; 2 running XP and one on Vista. The computer that can't connect to the internet (XP) is old and failing, and shows no warning before it completely runs out of battery. Thus today, I started it up forgetting that I had unplugged it the night before, and it just ran out of battery entirely whilst I was using it and died. I think that before this I had been browsing the internet, but I can't remember for certain. (i.e. The problem I am having may or may not have been caused by this 'hard' power off). Anyway, now when I start the computer up it takes 5-10 minutes after logging on to display the start bar and icons. Also, I cannot browse the internet. The computer seems to connect to the network OK (I have tried both wired and wireless), but I can't visit sites and can't ping web addresses. Pinging the router fails, as does pinging another of my computers on the network. I have never encountered something like this before, and whilst I am no noob I am also not a sysadmin, haha. :( Any help is greatly appreciated, thank you for your time. P.S. I have tried a system restore (newbie move?).

  Read the article

• Video output vanishes and it isn't the video card... suggestions?

  - by Ira Baxter

  I have a high-end dual processor Dell workstation that operated for several years without problem. Recently, the video output has gone flaky, in the sense that after 2-3 days, it loses synch with the monitor (sometimes you can still see a hashed-mess of the what you expect to see on the screen). Poking at the keyboard, and accessing the file system on the machine from over the network, indicates that the machine is running fine and its just the video. A reboot fixes the problem... for another day or two. This in effect makes the machine unusable. So, I replaced the video card with an exact duplicate bought from e-bay. (I checked after the dupe arrived to be sure, yep, same model number). I still get the same behavior. So unless I believe that both video cards are broken the same way, I have to beleive this is a problem with the motherboard/power supply, neither of which I am inclined to replace. The only other possibility I can think of is a Windows update to the graphics driver. How would I check for this? Anybody had a similar problem? Otherwise we're junking what used to be a perfectly good machine. (Another couple of hours of more wasted effort and that's it in terms of economics anyway).

  Read the article

• Intel Motherboard Lightning Victim Dies Hard

  - by Stetson RDT

  Today, I have a more hardware-related question. I have an Intel board, and I really do not know which board it is, I built the machine for a relative, but he forgot to keep the documentation. Long story short, the computer was disconnected during a lightning storm, but a lightning strike travelled in via the ethernet cable (It was directly connected to a power brick commonly seen on those long distance ISP Wireless transmitters), and the motherboard was shocked. I am attempting to get this PC going. The problem is as follows: The computer will randomly reboot, just in the middle of anything as it pleases. May load to EFI (or whatever BIOS is nowadays), may load to bootloader, may even get to the OS. But before 5 minutes is up, the system will always die. Out of curiosity, I plugged my voltmeter in to a molex connector. On the 5V side, it gets a good, consistant +5.13V. On the 12V side, it fluctuates, as follows: Upon immediate startup, it soars to 12.11-12.13V. It will now do one of two things: it will immediately jump down to 12.04-12.05V, or hover for about a minute at 12.11-12.13, then jump down. It seems the longer the voltage stays at 12.11-12.13, the shorter the machine will stay running. Also, post codes, whenever the machine locks up, but does not die hard, seem to be between "AA" and "AC". Does this make any sense to anybody? Do you all think this motherboard is salvageable? It was an expensive bugger, and I'd prefer to not replace it.

  Read the article

• Is my motherboard failing, or is there some other issue?

  - by ThatGuy

  So, several months ago I put together my own desktop PC. I set up a dual boot to Windows and Ubuntu. Recently, without changing any settings or installing anything new, the wifi stopped working on windows (I use a wifi adapter). It said it was connected, Network settings showed that it was working and running trouble shooting had no results. My internet still works on any other device. I found that removing the adapter from the motherboard and plugging it back in was the only thing that fixed the problem. Reinstalling the wifi drivers did not help. I purchased a new Wifi adapter, but the problem persists. More recently, I had a much more discouraging development. Sometimes, turning on the computer results in a boot loop: BIOS never starts. Instead, the monitor turns on as if it got a signal, then immediately turns off. This loops on it's own indefinitely until I hold down power, hard reset it, and try again. Sometimes it works, sometimes it doesn't. I haven't tested much on the Ubuntu side. It appears that wifi works at least some of the time, but since I've had issues just getting to BIOS I'm not confident the issue is on the software side. I've also noticed issues with some of the USB ports no longer working, but that seems to be off and on. Finally, as of a few minutes ago, I booted to windows to discover that everything was running very slowly. Slow here is a relative word, but I have a Samsung 840 pro SSD and I'm used to applications running nigh instantly, and it was a solid 3 minutes before any of my applications would load. Anyway, my question is this: Is it likely that my motherboard is failing? Either way, what steps can I take to try and pin down the problem and figure out what to do?

  Read the article

• Computer won't start up. Stuck on Lenovo splash screen. Help Diagnose

  - by Ace Legend

  I have some (I'm not sure exactly what model) Lenovo 21" IdeaCentre. Honestly, the computer works off and on. I have had problems with it not being able to shutdown, which I fixed. The fan seems to be constantly running, a few other problems as well. Anyway, nobody was using it when all of a sudden it switched to a blue screen. I was in the kitchen, but when I got over to the computer I read the message. It said something about bad drivers, but that is all I saw and then it restarted. However, when it got to the Lenovo Splash screen, nothing happened. I waited there for over 10 minutes, but still nothing. I tried to turn of the computer, but the only way to do it was to pull out the power cable. I then removed all USB devices and tried again. Still nothing. It also won't respond to keyboard input when I try to use enter to interrupt normal startup. My guess is some piece of hardware is damaged inside the machine. However, I have no idea what piece it is. Does anybody have any idea what could be wrong with it? Thanks.

  Read the article

• Hard Drive problem: is it the SATA controller or the HDD itself?

  - by Drooling_Sheep

  I have a Samsung 1.5TB hard drive hooked up to an ECS H55H-I mini-ITX motherboard. I have XBMC 10 (modified Ubuntu 10.04) installed for use as an HTPC. The hard drive encounters occasional errors during normal use which cause it to be remounted read-only. I have updated the BIOS on the motherboard, changed the SATA cable and moved it to different ports on the motherboard, installed and re-installed the OS (including different versions of XBMC and generic ubuntu), all to no avail. I recently ran tests both with badblocks -sv and smartctl -t long. Both reported no errors. This makes me think the motherboard or SATA controller is probably the issue. Does anyone know of any further tests I can do to help narrow this down? The processor is a Core i3. I forget the model number but it's one of the 32nm ones with on-package graphics. There's no discrete video card or optical drive. The power supply is a 150W Rosewill (pretty sure) that came with the case.

  Read the article

• Seriousness of a "Smart" disk error. How long will it last?

  - by Workshop Alex

  I have an 1 TB data disk and the bios and Windows are reporting a "Smart" error. At least, I get a Smart event but it doesn't indicate how serious the failure could be. My system is about 6 months old, including the disk so the warranty will cover the damage. Unfortunately, I lack a second disk of 1 TB in size which I can use to make a full backup. The most important data on this disk is safe, but there's a lot of work data which can be regenerated but this would cost a lot of time. So I ordered an USB disk of 1 TB which will arrive in three days. By then I can make a full backup of the data and afterwards, it can crash. But will the disk live that long? (Well, I won't use the PC as long as I can't make a backup.) How serious is such a Smart event? I know it's serious enough to have it replaced, but will it live for another week or could it die any moment?Update: I purchased an 1 TB external disk and spent most of the day making a backup of the 1 TB disk. It survived that. I then received a new disk, since it was still under warranty and replaced the hard disk. Then I had to spend most of a day again to put back the backup. I need to send back the faulty disk and now have an additional external disk, which could always be practical. :-) The Smart Error report did not cause any failures on the original disk. I won't advise to ignore these warnings, but the disk still has enough life in it to last a few more days. (Just make sure you have a good back-up.) And oh, the horror of having to make a complete backup such a huge disk. :-) If your data is important, make sure you have something that supports incremental backups and lots of space. (In my case, the data wasn't very important, just practical to have on-disk together.)

  Read the article

• Repair corrupt hard disk on Mac without install CD

  - by Sarah

  The hard disk of my late 2009 MacBook Pro appears to have become corrupted. I am traveling and do not have my install CD (and won't for several weeks, nor will I be anywhere near an Apple store). The hard disk is not the original, which failed in June 2011. It's some Hitachi replacement installed by IT. History: I was typing an email this afternoon, my computer suddenly started making soft clicking sounds and then froze. I was not moving around. I rebooted, which took a while. I heard more clicking sounds and the computer froze at least once again. It's now kind of working, with mdworker sucking up one CPU. There are no awkward hard drive sounds when I run Chrome or play music. However, when I launched Stickies, I found no trace of my saved Stickies. I ran a live disk verification from within Disk Utility, and it reported Problem: As reported, I don't have access to an installation disc and am nowhere near an area where I can get one for at least two weeks. I have the option of asking someone to go to some trouble and expense to get one for me, but I'm not sure it's worth it: I've read that I can use fsck from single-user mode to repair the disk. Should I just try this? Is it risky? I'm concerned that the clicky sound portends imminent (mechanical) hard drive failure, so it's not worth doing a silly repair. This hard disk is backed up, but I definitely won't be able to access the backup while traveling. I'd like to maximize the probability that I can keep using my computer (and all its current files) while traveling. Update I bit the bullet and ran fsck -fy from single-user mode. It only needed one pass (modification) to reach the "okay" stage. However, rebooting took nearly 5 min and involved several rounds of scratchy sounds and a few bad clicks. I'm now back to kind of using my computer (the same files are missing as before). When I ran live disk verification from Disk Utility this time, however, it reported that the volume appears to be OK. Am I right to infer from the scratchy sounds, however, that my hard drive is still rapidly on its way out? Is there anything else I can do to increase its functionality over the next few weeks?

  Read the article

• Security failure - This is not a secure document but has security embed parameters

  - by dimitris mistriotis

  I try to create a private version and therefore I used something like this in php: var scribd_doc = scribd.Document.getDoc( 28394353, 'xxx'); scribd_doc.addParam("use_ssl", true); scribd_doc.addParam('public', false); scribd_doc.grantAccess("cbccf6e7-1ff7-9034-8a7c-a0c2a5b225ed", <?php echo "'" . trim($_COOKIE['PHPSESSID']) . "'" ?>, <?php echo "'" . scribd_calculate_signature($documentID = '28394353', $sessionID = trim($_COOKIE['PHPSESSID']), $userID = "cbccf6e7-1ff7-9034-8a7c-a0c2a5b225ed") . "'" ?>); ... ... scribd_doc.write( 'embedded_flash' ); Which is the api of scribd for javascript with the addition of the signature. My result is the "Security failure - This is not a secure document but has security embed parameters" Error, which is not well documented. The document is set to private. Any ideas?

  Read the article

• PC hangs and reboots from time to time

  - by Bevor

  Hello, I have a very strange problem: Since I have my new PC, I have always had problems with it. From time to time the computer freezes for some seconds and suddendly reboots by itself. I've had this problem since Ubuntu 9.10. The same with 10.04 and 10.10. That's why I don't think it's a software failure because the problem persist too long. It doesn't have anything to do with what I'm doing at this time. Sometimes I listen to music, sometimes I only use Firefox, sometimes I'm running 2 or 3 VMs, sometimes I watch DVD. So it's not isolatable. I could freeze once a day or once a week. I put the PC to the vendor twice(!). The first time they changed my power supply but the problem persisted. The second time they told me that they made some heavy performance tests 50 hours long but they didn't find anything. (How can that be that I have daily freezes with normal usage). The vendor didn't check the hard discs because they used their own disc with Windows. (So they never checked the Linux installation). Yesterday I made some intensive hard disc scans with "SMART" but no errors were found. I ran memtest for 3 times but no errors found. I already had this problem in my old flat, so I doubt that I has something to do with current fluctuation. I already tried another electrical socket and changed to connector strip but the problem persists. At the moment I removed 2 of the RAMs (2x 2GB). In all I have 6GB, 2x2GB and 2x1GB. Could this difference maybe be a problem? Here is a list of my components. I hope that anybody find something I didn't think about yet. And here a list of my components: 1x AMD Phenom II X4 965 Black Edition, 3,4Ghz, Quad Core, S-AM3, Boxed 2x DDR3-RAM 2048MB, PC3-1333 Mhz, CL9, Kingston ValueRAM 2x DDR3-RAM 1024MB, PC3-1333 Mhz, CL9, Kingston ValueRAM 2x SATA II Seagate Barracuda 7200.12, 1TB 32MB Cache = RAID 1 1x DVD ROM SATA LG DH16NSR, 16x/52x 1x DVD-+R/-+RW SATA LG GH-22NS50 1x Cardreader 18in1 1x PCI-E 2.0 GeForce GTS 250, Retail, 1024MB 1x Power Supply ATX 400 Watt, CHIEFTEC APS-400S, 80 Plus 1x Network card PCI Intel PRO/1000GT 10/100/1000 MBit 1x Mainboard Socket-AM3 ASUS M4A79XTD EVO, ATX lshw: description: Desktop Computer product: System Product Name vendor: System manufacturer version: System Version serial: System Serial Number width: 64 bits capabilities: smbios-2.5 dmi-2.5 vsyscall64 vsyscall32 configuration: boot=normal chassis=desktop uuid=80E4001E-8C00-002C-AA59-E0CB4EBAC29A *-core description: Motherboard product: M4A79XTD EVO vendor: ASUSTeK Computer INC. physical id: 0 version: Rev X.0X serial: MT709CK11101196 slot: To Be Filled By O.E.M. *-firmware description: BIOS vendor: American Megatrends Inc. physical id: 0 version: 0704 (11/25/2009) size: 64KiB capacity: 960KiB capabilities: isa pci pnp apm upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb ls120boot zipboot biosbootspecification *-cpu description: CPU product: AMD Phenom(tm) II X4 965 Processor vendor: Advanced Micro Devices [AMD] physical id: 4 bus info: cpu@0 version: AMD Phenom(tm) II X4 965 Processor serial: To Be Filled By O.E.M. slot: AM3 size: 800MHz capacity: 3400MHz width: 64 bits clock: 200MHz capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp x86-64 3dnowext 3dnow constant_tsc rep_good nonstop_tsc extd_apicid pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs skinit wdt npt lbrv svm_lock nrip_save cpufreq *-cache:0 description: L1 cache physical id: 5 slot: L1-Cache size: 512KiB capacity: 512KiB capabilities: pipeline-burst internal varies data *-cache:1 description: L2 cache physical id: 6 slot: L2-Cache size: 2MiB capacity: 2MiB capabilities: pipeline-burst internal varies unified *-cache:2 description: L3 cache physical id: 7 slot: L3-Cache size: 6MiB capacity: 6MiB capabilities: pipeline-burst internal varies unified *-memory description: System Memory physical id: 36 slot: System board or motherboard size: 2GiB *-bank:0 description: DIMM Synchronous 1333 MHz (0.8 ns) product: ModulePartNumber00 vendor: Manufacturer00 physical id: 0 serial: SerNum00 slot: DIMM0 size: 1GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: DIMM Synchronous 1333 MHz (0.8 ns) product: ModulePartNumber01 vendor: Manufacturer01 physical id: 1 serial: SerNum01 slot: DIMM1 size: 1GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:2 description: DIMM [empty] product: ModulePartNumber02 vendor: Manufacturer02 physical id: 2 serial: SerNum02 slot: DIMM2 *-bank:3 description: DIMM [empty] product: ModulePartNumber03 vendor: Manufacturer03 physical id: 3 serial: SerNum03 slot: DIMM3 *-pci:0 description: Host bridge product: RD780 Northbridge only dual slot PCI-e_GFX and HT1 K8 part vendor: ATI Technologies Inc physical id: 100 bus info: pci@0000:00:00.0 version: 00 width: 32 bits clock: 66MHz *-pci:0 description: PCI bridge product: RD790 PCI to PCI bridge (external gfx0 port A) vendor: ATI Technologies Inc physical id: 2 bus info: pci@0000:00:02.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:a000(size=4096) memory:f8000000-fbbfffff ioport:d0000000(size=268435456) *-display description: VGA compatible controller product: G92 [GeForce GTS 250] vendor: nVidia Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:18 memory:fa000000-faffffff memory:d0000000-dfffffff memory:f8000000-f9ffffff ioport:ac00(size=128) memory:fbbe0000-fbbfffff *-pci:1 description: PCI bridge product: RD790 PCI to PCI bridge (PCI express gpp port C) vendor: ATI Technologies Inc physical id: 6 bus info: pci@0000:00:06.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:41 ioport:b000(size=4096) memory:fbc00000-fbcfffff ioport:f6f00000(size=1048576) *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: e0:cb:4e:ba:c2:9a size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:45 ioport:b800(size=256) memory:f6fff000-f6ffffff memory:f6ff8000-f6ffbfff memory:fbcf0000-fbcfffff *-pci:2 description: PCI bridge product: RD790 PCI to PCI bridge (PCI express gpp port D) vendor: ATI Technologies Inc physical id: 7 bus info: pci@0000:00:07.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:42 ioport:c000(size=4096) memory:fbd00000-fbdfffff *-firewire description: FireWire (IEEE 1394) product: VT6315 Series Firewire Controller vendor: VIA Technologies, Inc. physical id: 0 bus info: pci@0000:03:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress ohci bus_master cap_list configuration: driver=firewire_ohci latency=0 resources: irq:19 memory:fbdff800-fbdfffff ioport:c800(size=256) *-pci:3 description: PCI bridge product: RD790 PCI to PCI bridge (PCI express gpp port E) vendor: ATI Technologies Inc physical id: 9 bus info: pci@0000:00:09.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:43 ioport:d000(size=4096) memory:fbe00000-fbefffff *-ide description: IDE interface product: 88SE6121 SATA II Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:04:00.0 version: b2 width: 32 bits clock: 33MHz capabilities: ide pm msi pciexpress bus_master cap_list configuration: driver=pata_marvell latency=0 resources: irq:17 ioport:dc00(size=8) ioport:d880(size=4) ioport:d800(size=8) ioport:d480(size=4) ioport:d400(size=16) memory:fbeffc00-fbefffff *-storage description: SATA controller product: SB700/SB800 SATA Controller [IDE mode] vendor: ATI Technologies Inc physical id: 11 bus info: pci@0000:00:11.0 logical name: scsi0 logical name: scsi2 version: 00 width: 32 bits clock: 66MHz capabilities: storage msi ahci_1.0 bus_master cap_list emulated configuration: driver=ahci latency=64 resources: irq:44 ioport:9000(size=8) ioport:8000(size=4) ioport:7000(size=8) ioport:6000(size=4) ioport:5000(size=16) memory:f7fffc00-f7ffffff *-disk:0 description: ATA Disk product: ST31000528AS vendor: Seagate physical id: 0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: CC38 serial: 9VP3WD9Z size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=000ad206 *-volume:0 UNCLAIMED description: Linux filesystem partition vendor: Linux physical id: 1 bus info: scsi@0:0.0.0,1 version: 1.0 serial: 81839235-21ea-4853-90a4-814779f49000 size: 972MiB capacity: 972MiB capabilities: primary ext2 initialized configuration: filesystem=ext2 modified=2010-12-06 18:32:58 mounted=2010-11-01 07:05:10 state=unknown *-volume:1 UNCLAIMED description: Linux swap volume physical id: 2 bus info: scsi@0:0.0.0,2 version: 1 serial: 22b881d5-6f5c-484d-94e8-e231896fa91b size: 486MiB capacity: 486MiB capabilities: primary nofs swap initialized configuration: filesystem=swap pagesize=4096 *-volume:2 UNCLAIMED description: EXT3 volume vendor: Linux physical id: 3 bus info: scsi@0:0.0.0,3 version: 1.0 serial: ad5b0daf-11e8-4f8f-8598-4e89da9c0d84 size: 47GiB capacity: 47GiB capabilities: primary journaled extended_attributes large_files recover ext3 ext2 initialized configuration: created=2010-02-16 20:42:29 filesystem=ext3 modified=2010-11-29 17:02:34 mounted=2010-12-06 18:32:50 state=clean *-volume:3 UNCLAIMED description: Extended partition physical id: 4 bus info: scsi@0:0.0.0,4 size: 882GiB capacity: 882GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume UNCLAIMED description: Linux filesystem partition physical id: 5 capacity: 882GiB *-disk:1 description: ATA Disk product: ST31000528AS vendor: Seagate physical id: 1 bus info: scsi@2:0.0.0 logical name: /dev/sdb version: CC38 serial: 9VP3SCPF size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=000ad206 *-volume:0 UNCLAIMED description: Linux filesystem partition vendor: Linux physical id: 1 bus info: scsi@2:0.0.0,1 version: 1.0 serial: 81839235-21ea-4853-90a4-814779f49000 size: 972MiB capacity: 972MiB capabilities: primary ext2 initialized configuration: filesystem=ext2 modified=2010-12-06 18:32:58 mounted=2010-11-01 07:05:10 state=unknown *-volume:1 UNCLAIMED description: Linux swap volume physical id: 2 bus info: scsi@2:0.0.0,2 version: 1 serial: 22b881d5-6f5c-484d-94e8-e231896fa91b size: 486MiB capacity: 486MiB capabilities: primary nofs swap initialized configuration: filesystem=swap pagesize=4096 *-volume:2 UNCLAIMED description: EXT3 volume vendor: Linux physical id: 3 bus info: scsi@2:0.0.0,3 version: 1.0 serial: ad5b0daf-11e8-4f8f-8598-4e89da9c0d84 size: 47GiB capacity: 47GiB capabilities: primary journaled extended_attributes large_files recover ext3 ext2 initialized configuration: created=2010-02-16 20:42:29 filesystem=ext3 modified=2010-11-29 17:02:34 mounted=2010-12-06 18:32:50 state=clean *-volume:3 UNCLAIMED description: Extended partition physical id: 4 bus info: scsi@2:0.0.0,4 size: 882GiB capacity: 882GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume UNCLAIMED description: Linux filesystem partition physical id: 5 capacity: 882GiB *-usb:0 description: USB Controller product: SB700/SB800 USB OHCI0 Controller vendor: ATI Technologies Inc physical id: 12 bus info: pci@0000:00:12.0 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:16 memory:f7ffd000-f7ffdfff *-usb:1 description: USB Controller product: SB700 USB OHCI1 Controller vendor: ATI Technologies Inc physical id: 12.1 bus info: pci@0000:00:12.1 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:16 memory:f7ffe000-f7ffefff *-usb:2 description: USB Controller product: SB700/SB800 USB EHCI Controller vendor: ATI Technologies Inc physical id: 12.2 bus info: pci@0000:00:12.2 version: 00 width: 32 bits clock: 66MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=64 resources: irq:17 memory:f7fff800-f7fff8ff *-usb:3 description: USB Controller product: SB700/SB800 USB OHCI0 Controller vendor: ATI Technologies Inc physical id: 13 bus info: pci@0000:00:13.0 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:18 memory:f7ffb000-f7ffbfff *-usb:4 description: USB Controller product: SB700 USB OHCI1 Controller vendor: ATI Technologies Inc physical id: 13.1 bus info: pci@0000:00:13.1 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:18 memory:f7ffc000-f7ffcfff *-usb:5 description: USB Controller product: SB700/SB800 USB EHCI Controller vendor: ATI Technologies Inc physical id: 13.2 bus info: pci@0000:00:13.2 version: 00 width: 32 bits clock: 66MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=64 resources: irq:19 memory:f7fff400-f7fff4ff *-serial UNCLAIMED description: SMBus product: SBx00 SMBus Controller vendor: ATI Technologies Inc physical id: 14 bus info: pci@0000:00:14.0 version: 3c width: 32 bits clock: 66MHz capabilities: ht cap_list configuration: latency=0 *-ide description: IDE interface product: SB700/SB800 IDE Controller vendor: ATI Technologies Inc physical id: 14.1 bus info: pci@0000:00:14.1 logical name: scsi5 version: 00 width: 32 bits clock: 66MHz capabilities: ide msi bus_master cap_list emulated configuration: driver=pata_atiixp latency=64 resources: irq:16 ioport:1f0(size=8) ioport:3f6 ioport:170(size=8) ioport:376 ioport:ff00(size=16) *-cdrom:0 description: DVD reader product: DVDROM DH16NS30 vendor: HL-DT-ST physical id: 0.0.0 bus info: scsi@5:0.0.0 logical name: /dev/cdrom1 logical name: /dev/dvd1 logical name: /dev/scd0 logical name: /dev/sr0 version: 1.00 capabilities: removable audio dvd configuration: ansiversion=5 status=nodisc *-cdrom:1 description: DVD-RAM writer product: DVDRAM GH22NS50 vendor: HL-DT-ST physical id: 0.1.0 bus info: scsi@5:0.1.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd1 logical name: /dev/sr1 version: TN02 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-multimedia description: Audio device product: SBx00 Azalia (Intel HDA) vendor: ATI Technologies Inc physical id: 14.2 bus info: pci@0000:00:14.2 version: 00 width: 64 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: driver=HDA Intel latency=64 resources: irq:16 memory:f7ff4000-f7ff7fff *-isa description: ISA bridge product: SB700/SB800 LPC host controller vendor: ATI Technologies Inc physical id: 14.3 bus info: pci@0000:00:14.3 version: 00 width: 32 bits clock: 66MHz capabilities: isa bus_master configuration: latency=0 *-pci:4 description: PCI bridge product: SBx00 PCI to PCI Bridge vendor: ATI Technologies Inc physical id: 14.4 bus info: pci@0000:00:14.4 version: 00 width: 32 bits clock: 66MHz capabilities: pci subtractive_decode bus_master resources: ioport:e000(size=4096) memory:fbf00000-fbffffff *-network description: Ethernet interface product: 82541PI Gigabit Ethernet Controller vendor: Intel Corporation physical id: 5 bus info: pci@0000:05:05.0 logical name: eth1 version: 05 serial: 00:1b:21:56:f3:60 size: 100MB/s capacity: 1GB/s width: 32 bits clock: 66MHz capabilities: pm pcix bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000 driverversion=7.3.21-k6-NAPI duplex=full firmware=N/A ip=192.168.1.2 latency=64 link=yes mingnt=255 multicast=yes port=twisted pair speed=100MB/s resources: irq:20 memory:fbfe0000-fbffffff memory:fbfc0000-fbfdffff ioport:ec00(size=64) memory:fbfa0000-fbfbffff *-usb:6 description: USB Controller product: SB700/SB800 USB OHCI2 Controller vendor: ATI Technologies Inc physical id: 14.5 bus info: pci@0000:00:14.5 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:18 memory:f7ffa000-f7ffafff *-pci:1 description: Host bridge product: Family 10h Processor HyperTransport Configuration vendor: Advanced Micro Devices [AMD] physical id: 101 bus info: pci@0000:00:18.0 version: 00 width: 32 bits clock: 33MHz *-pci:2 description: Host bridge product: Family 10h Processor Address Map vendor: Advanced Micro Devices [AMD] physical id: 102 bus info: pci@0000:00:18.1 version: 00 width: 32 bits clock: 33MHz *-pci:3 description: Host bridge product: Family 10h Processor DRAM Controller vendor: Advanced Micro Devices [AMD] physical id: 103 bus info: pci@0000:00:18.2 version: 00 width: 32 bits clock: 33MHz *-pci:4 description: Host bridge product: Family 10h Processor Miscellaneous Control vendor: Advanced Micro Devices [AMD] physical id: 104 bus info: pci@0000:00:18.3 version: 00 width: 32 bits clock: 33MHz configuration: driver=k10temp resources: irq:0 *-pci:5 description: Host bridge product: Family 10h Processor Link Control vendor: Advanced Micro Devices [AMD] physical id: 105 bus info: pci@0000:00:18.4 version: 00 width: 32 bits clock: 33MHz *-scsi physical id: 1 bus info: usb@2:3 logical name: scsi8 capabilities: emulated scsi-host configuration: driver=usb-storage *-disk:0 description: SCSI Disk physical id: 0.0.0 bus info: scsi@8:0.0.0 logical name: /dev/sdc *-disk:1 description: SCSI Disk physical id: 0.0.1 bus info: scsi@8:0.0.1 logical name: /dev/sdd *-disk:2 description: SCSI Disk physical id: 0.0.2 bus info: scsi@8:0.0.2 logical name: /dev/sde *-disk:3 description: SCSI Disk physical id: 0.0.3 bus info: scsi@8:0.0.3 logical name: /dev/sdf *-network DISABLED description: Ethernet interface physical id: 1 logical name: vboxnet0 serial: 0a:00:27:00:00:00 capabilities: ethernet physical configuration: broadcast=yes multicast=yes

  Read the article

• Computer loses all installed programs and appears to return OS-only state

  - by Jake

  This is a story regarding 3 laptops of different brand and models. On separate occassions, I configured each of these Windows 7 / Vista computers with the necessary configuration and applications (which are supposedly the same actually), e.g. join office domain, same windows updates, microft office etc. These machinese were configure in our office in Singapore, and then they were taken to India for use. Someday in India, when booting up the laptop, all went fine except when it reach the log in screen, it was no longer possible to login with domain credentials. Logging into the laptop local admin account will lead to discover that the machine has returned to "OS-only state". All the configurations and applications were gone. The actual user profiles are still in the C: drive so files can still be retrieved, but under Control Panel Uninstall Programs it is evident that at least the registry is corrupted. The above scenario happen to the first 2 laptops. For the third, the system reports "Operating System Not Found" on boot up. I cannot think of any reason except to suspect a power fluctuation issue. Question is, will a power issue create this behaviour? What else can cause this issue?

  Read the article

• Are These Parts compatible?

  - by ell

  I have never assembled a PC before, although I have taken an old one apart and replaced a few parts in others here and there so I have (very) limited experience. I have been looking to make a pc and here are the parts I might buy: Foxconn P45AL Intel P45 (Socket 775) DDR2 Motherboard (with onboard sound I believe) Gigabyte GeForce GTX 460 OC 768MB GDDR5 PCI-Express Graphics Card Already have 2 1gb sticks of dual channel DDR2 memory Intel Core 2 Quad Q8400 LGA775 'Yorkfield' 2.66GHz 4MB-cache Processor Samsung SpinPoint F3 1TB SATA-II 32MB Cache Hard Drive Antec Dark Fleet Series DF10 Gaming Enclosure – Black I already have monitor, mouse, keyboard and DVD/CD drive Akasa Freedom Power 1000W Modular Power Supply I have never done this before so feel free to laugh at me for getting something obvious wrong, forgetting a vital component etc. but is all of this compatible? And have I gone overkill on the PSU, if so, please recommend one. Thanks in advance, ell. EDIT: Added PSU which I forgot to mention EDIT: I would be using this to surf the internet, write e-mails, chat, word process, play games such as team fortress 2 & spring rts (at highest graphics hopefully), some 3d modelling in blender, some opengl programming, and image editing in GIMP.

  Read the article

• Ret Failure with SDL using FASM on Win32

  - by Jon Purdy

  I'm using SDL with FASM, and have code that's minimally like the following: format ELF extrn _SDL_Init extrn _SDL_SetVideoMode extrn _SDL_Quit extrn _exit SDL_INIT_VIDEO equ 0x00000020 section '.text' public _SDL_main _SDL_main: ccall _SDL_Init, SDL_INIT_VIDEO ccall _SDL_SetVideoMode, 640, 480, 32, 0 ccall _SDL_Quit ccall _exit, 0 ; Success, or ret ; failure. With the following quick-and-dirty makefile: SOURCES = main.asm OBJECTS = main.o TARGET = SDLASM.exe FASM = C:\fasm\fasm.exe release : $(OBJECTS) ld $(OBJECTS) -LC:/SDL/lib/ -lSDLmain -lSDL -LC:/MinGW/lib/ -lmingw32 -lcrtdll -o $(TARGET) --subsystem windows cleanrelease : del $(OBJECTS) %.o : %.asm $(FASM) $< $@ Using exit() (or Windows' ExitProcess()) seems to be the only way to get this program to exit cleanly, even though I feel like I should be able to use retn/retf. When I just ret without calling exit(), the application does not terminate and needs to be killed. Could anyone shed some light on this? It only happens when I make the call to SDL_SetVideoMode().

  Read the article

• Windows 7 hangs after going into sleep a second time

  - by Brian Stephenson

  I've searched everywhere around Google and can't figure out why this is happening so I decide to ask here to see if anyone has a problem like this. Like it says in the title, whenever I sleep ONCE I'm able to wake the system, but going back to sleep again AFTER waking up for the first time results in it hanging on no input and no output, with the fan spinning as fast as possible and alot of heat being spewed out by the fan as well. I've tried various things like setting all USB Hub Root's to not get switched off for power saving, disabling USB selective suspend, disabling PCI-e link state power management, and even unplugging ALL USB devices and it wont wake up after the second attempt. And I've even waited up to a full hour of the CPU fan spinning loudly and it's still stuck trying to wake up. The only USB devices I use are a Microsoft USB Comfort Curve Keyboard 2000 (IntelliType Pro) and a generic HID compliant mouse from Creative model number OMC90S "CREATIVE MOUSE OPTICAL LITE". My other devices like external drives and controllers are unplugged when I'm not using them as having too many USB devices plugged in at a time causes a deadlock on almost all of the ports I have. Here's my system specifications (Most of these are from CPU-Z): Brand: Gateway DX4300-19 Mainboard: Gateway RS780 Chipset: AMD 780G Rev 00 Southbridge: AMD SB700 Rev 00 LPCIO: ITE IT8718 BIOS: American Megatrends Inc. ver P01-A4 09/15/2009 CPU: AMD Phenom II X4 810 at 2.60 GHz RAM: 8.0 GB DDR2 Dual Channel Ganged Mode at 400 MHz GPU: ATI Radeon HD3200 Graphics Intergrated - RS780 OS: Windows 7 Home Premium x64 OEM (Acer Group) HDD: WDC WD10EADS-22M2B0 1.0 TB (Western Digital Green Caviar) My BIOS has absolutely no control over how I setup the sleep mode to be either S1 or S3. So I can't check these settings or even change them. Hybrid sleep is also disabled, I can successfully go into hibernation and wake from hibernation but this is painfully slow due to a harddrive problem I'm having with this "Green Drive". (Hibernation takes over ~3 minutes to complete) Any help would be appreciated, thanks.

  Read the article

• Maven test failure xml FileNotFoundException

  - by James

  My Maven build is failing on Hudson with a FileNotFoundException, I do not get the same failure through NetBeans. The FileNotFoundException is for some xml files in the same packages as my test classes themselves. It would appear these are not getting copied as part of the build in the same way the class files are. Do I have to add something to my POM for the xml files to be copied? If any more information is required please let me know, I wanted to keep the question short incase it was something simple.

  Read the article

• Computer sponteously reboots when doing heavy file copy to/from disk

  - by Mark Hosang

  I've been fighting with this problem for the last 3 weeks where my machine will just instantly reboot. No BSOD, and when i checked the event log all that was reported was the generic "Kernal-power" error with the detailed information pointing to a hard crash. This is a machine that was working for 18 months before these crashes started happening. When they started happening is after I added 3 HDs in a RAID-5, upped the memory to 12gb, moved to a new house, added a SSD and added about 5 case fans. I have thus eliminated the RAID, and determined that the SSD was not the cause (because it was still crashing even though the ssd wasn't connected). I've run memtest several times over night with no memory problems showing up. I've run IntelBurnTest to max out the cpu to see if it was a heat issue and at full tilt after 20 min it was only at 85C and the machine didn't crash. I also took a look at the voltages during this test, with a screenshot at the bottom of this post I've ruled out a software issue by reinstalling windows 7 ultimate x64 a total of 5 times, but even during that the install it crashes. Happens sometime during file copying at the beginning, or during uncompressing files, or sometimes during running windows update. The only discernible pattern i can see is that it seems to crash when hard disks might be spinning up or when they are accessed heavily from large file transfers. My current guess is that it is probably an issue with the MB, PSU or the power coming through the outlet. Any suggestions of what i could try to troubleshoot or what may be wrong? Specs PSU: Seasonic M12 700w Mem: 12gb CPU: i7-920 with stock heatsink MB: Asus P6T HDs: 3 green WD and 1 Corsair force 3 120b with 1.3.3 firmware Running full tilt voltages Idling Voltages

  Read the article

• Simple electric DC question. Current consumption

  - by Bobb

  Suppose you have DC power supply and a consumer connected to it (i.e. computer PSU and a hard drive). Suppose PSU which was supplied with the consumer has output 5V 1A. So I assume that the consumer should not consume more than 1A. Suppose the original PSU is broken now and I want to replace it with the one I have which is 5V 10A. My guess is that current is something which depends on the consumer. So if the consumer consumes normally 1A then it will not consume more than that even if it is connected to 10A PSU. In other word - am I right assuming that the consumer will not burn out being connected to a power supply with higher current output? P.S. my understanding is that voltage is something independent from the consumer. If you give it higher voltage it will burn (voltage is from PSU to the consumer). However current must be in opposite - consumer sucks as much current as it need not as much as PSU can provide (of course given that max PSU current is greater than the consumer needs)

  Read the article

• At what point does the performance gap between GPU & CPU become so great that the CPU is holding back a system?

  - by Matthew Galloway

  I know that generally speaking for gaming performance the GPU is the primary factor which holds back performance, with everything else such as RAM/motherboard/PSU/CPU being secondary in importance to the graphics card. But at some point the other components ARE going to be significant in holding back the whole system! For instance nobody would be silly enough to play modern games with 512MB RAM and the very latest graphics cards (such as an HD7970) as I bet the performance increase over such a system with only 512MB but a mid range card would be non-existent! Thus it would be a "waste" for such a person to buy any high end graphics card without resolving first the system's other problems. The same point applies to other components, such as if it only had a Pentium II a current high end graphics card would be wasted on it! So my core question is how do you determine at what point for your system is spending on extra GPU power be completely "wasted"? (also, a slightly more nuanced question is trying work out at what point might the extra graphics power not be "wasted" but would be "sub optimal" value for money, when the expenditure should then be split around graphics card and other components. As obviously a gamer shouldn't always just spend on upgrading the graphics card! But needs to balance it out)

  Read the article

• Simple electric DC question. Currency consumption

  - by Bobb

  Suppose you have DC power supply and a consumer connected to it (i.e. computer PSU and a hard drive). Suppose PSU which was supplied with the consumer has output 5V 1A. So I assume that the consumer should not consume more than 1A. Suppose the original PSU is broken now and I want to replace it with the one I have which is 5V 10A. My guess is that current is something which depends on the consumer. So if the consumer consumes normally 1A then it will not consume more than that even if it is connected to 10A PSU. In other word - am I right assuming that the consumer will not burn out being connected to a power supply with higher current output? P.S. my understanding is that voltage is something independent from the consumer. If you give it higher voltage it will burn (voltage is from PSU to the consumer). However current must be in opposite - consumer sucks as much current as it need not as much as PSU can provide (of course given that max PSU current is greater than the consumer needs)

  Read the article

• Computer does not boot, often

  - by tam

  I've ran into a issue with my computer that it does no longer reach POST, but simply powers on for a fraction of a second and powers off. But this is not always, some times it boots just normally and it works as it should, no issues with not enough power or anything. But as soon as I turn it of, I can not turn it back on, but then again at some random point it just powers up again, and resumes normal operation. If I disconnect the 8pin ATX connector from the motherboard, it powers up, fans and disks spinning normally until I power it off again. So this problem only happens when ATX is connected, which seems odd, I normally always saw this kind of an error if ATX was not connected, but here it's the exact opposite. It also does not emit any sound on the buzzer, except the normal beep, when it powers up normally. I have already tried: Remove graphics card Remove one and/or all RAM sticks Disconnect everything non-essential, even hard drives Clear CMOS I have not yet tried to remove all components and tried to boot everything outside of the case, because I did not have the time to disassemble and bleed the water loop. However, I can confirm that nothing is stuck underneath the motherboard, not is any of those brass raisers touching the board where it should not. Specs: Gigabyte GA-970A-UD3 AMD FX6300 ATI HD7850 I think this should be enough for this issue.

  Read the article

• Ldap invalid credentials not loading authentication failure url

  - by Murari

  Able to do the custom ldap authentication for external db authorities. But when i am trying to test wrong password the authentication failure url is not showing instead my browser prints the exception details.Below is my securitycontext.xml and exption given <http auto-config="false" access-decision-manager-ref="accessDecisionManager" access-denied-page="/accessDenied.jsp"> <!-- Restrict access to ALL other pages --> <intercept-url pattern="/index.jsp" filters="none" /> <!-- Don't set any role restrictions on login.jsp --> <intercept-url pattern="/**" access="IS_AUTHENTICATED_ANONYMOUSLY" /> <intercept-url pattern="/service/**" access="PRIV_Report User, PRIV_305" /> <logout logout-success-url="/index.jsp" /> <form-login authentication-failure-url="/index.jsp?error=1" default-target-url="/home.jsp" /> <anonymous/> </http> <b:bean id="accessDecisionManager" class="org.springframework.security.vote.AffirmativeBased"> <b:property name="decisionVoters"> <b:list> <b:ref bean="roleVoter" /> <b:ref bean="authenticatedVoter" /> </b:list> </b:property> </b:bean> <b:bean id="roleVoter" class="org.springframework.security.vote.RoleVoter"> <b:property name="rolePrefix" value="PRIV_" /> </b:bean> <b:bean id="authenticatedVoter" class="org.springframework.security.vote.AuthenticatedVoter"> </b:bean> <b:bean id="contextSource" class="org.springframework.security.ldap.DefaultSpringSecurityContextSource"> <b:constructor-arg value="ldap://mydomain:389" /> </b:bean> <b:bean id="ldapTemplate" class="org.springframework.ldap.core.LdapTemplate"> <b:constructor-arg ref="contextSource" /> </b:bean> <b:bean id="ldapAuthenticationProvider" class="com.zo.sas.gwt.security.login.server.SASLdapAuthenticationProvider"> <b:property name="authenticator" ref="ldapAuthenticator" /> <custom-authentication-provider /> </b:bean> <b:bean id="ldapAuthenticator" class="com.zo.sas.gwt.security.login.server.SASAuthenticator"> <b:property name="contextSource" ref="contextSource" /> <b:property name="userDnPatterns"> <b:value>uid={0},OU=People</b:value> </b:property> </b:bean> and my exception logs..... org.springframework.ldap.AuthenticationException: [LDAP: error code 49 - Invalid Credentials]; nested exception is javax.naming.AuthenticationException: [LDAP: error code 49 - Invalid Credentials] org.springframework.ldap.support.LdapUtils.convertLdapException(LdapUtils.java:180) org.springframework.ldap.core.support.AbstractContextSource.createContext(AbstractContextSource.java:266) org.springframework.ldap.core.support.AbstractContextSource.getContext(AbstractContextSource.java:106) com.zo.sas.gwt.security.login.server.SASAuthenticator.authenticate(SASAuthenticator.java:55) com.zo.sas.gwt.security.login.server.SASLdapAuthenticationProvider.authenticate(SASLdapAuthenticationProvider.java:45) org.springframework.security.providers.ProviderManager.doAuthentication(ProviderManager.java:188) org.springframework.security.AbstractAuthenticationManager.authenticate(AbstractAuthenticationManager.java:46) org.springframework.security.ui.webapp.AuthenticationProcessingFilter.attemptAuthentication(AuthenticationProcessingFilter.java:82) org.springframework.security.ui.AbstractProcessingFilter.doFilterHttp(AbstractProcessingFilter.java:258) org.springframework.security.ui.SpringSecurityFilter.doFilter(SpringSecurityFilter.java:53) org.springframework.security.util.FilterChainProxy$VirtualFilterChain.doFilter(FilterChainProxy.java:390) org.springframework.security.ui.logout.LogoutFilter.doFilterHttp(LogoutFilter.java:89) org.springframework.security.ui.SpringSecurityFilter.doFilter(SpringSecurityFilter.java:53) org.springframework.security.util.FilterChainProxy$VirtualFilterChain.doFilter(FilterChainProxy.java:390) org.springframework.security.context.HttpSessionContextIntegrationFilter.doFilterHttp(HttpSessionContextIntegrationFilter.java:235) org.springframework.security.ui.SpringSecurityFilter.doFilter(SpringSecurityFilter.java:53) org.springframework.security.util.FilterChainProxy$VirtualFilterChain.doFilter(FilterChainProxy.java:390) org.springframework.security.util.FilterChainProxy.doFilter(FilterChainProxy.java:175) org.springframework.web.filter.DelegatingFilterProxy.invokeDelegate(DelegatingFilterProxy.java:183) org.springframework.web.filter.DelegatingFilterProxy.doFilter(DelegatingFilterProxy.java:138) This is my index.jsp <html> <script type="text/javascript" language="javascript"> var dictionary = { loginErr: "${SPRING_SECURITY_LAST_EXCEPTION.message}", error: "${param.error}" }; </script> <head> </head> <body > <iframe src="javascript:''" id="__gwt_historyFrame" style="width:0;height:0;border:0"></iframe> <script type="text/javascript" language="javascript" src="com.zo.sas.gwt.sasworkflow.home.Home.nocache.js"></script> </body> </html>

  Read the article

• smtp exception "failure sending mail" in C#.net

  - by Ajay_Kumar

  Hello, I am making smtp mail application c#.net.This is working ok for Gmail setting but i have to work it for VSNL connection.I am getting an error exception "Failure sending mail" my setting seems looks perfect.What is the exact problem ? why this exception coming ? Thanks MailMessage mailMsg = new MailMessage(); MailAddress mailAddress = new MailAddress("[email protected]"); mailMsg.To.Add(textboxsecondry.Text); mailMsg.From = mailAddress; // Subject and Body mailMsg.Subject = "Testing mail.."; mailMsg.Body = "connection testing.."; SmtpClient smtpClient = new SmtpClient("smtp.vsnl.net", 25); System.Net.NetworkCredential credentials = new System.Net.NetworkCredential("[email protected]", "password"); smtpClient.EnableSsl = true; smtpClient.UseDefaultCredentials = false; smtpClient.Credentials = credentials; smtpClient.Send(mailMsg);

  Read the article

• Can I charge USB devices from a powered hub that isn't connected to a PC?

  - by Anodyne

  This will probably sound familiar to most of you... In my home, we have a whole bunch of devices that can be charged via USB (two iPhones, a BlackBerry, an iPod Touch, etc ad nauseam). We also have a bunch of USB chargers, each of which has a single USB port on it. I'd like to have something permanently connected to AC power with at least 4 USB ports on it, so we can just plug devices in and don't need to go looking for a free outlet. So here's the question: if I buy a powered USB hub, will that do the job even if I don't connect it to a PC? Ideally if you have a hub that you can personally verify will be suitable, let me know the manufacturer and model :-) Thanks in advance! EDIT: The solution I eventually went for was this: Kensington 4-Port USB Charger for Mobile Devices (Europe) There's also a US version here: Kensington 4-Port USB Charger for Mobile Devices (USA) It arrived yesterday, so I used it to charge the following devices, all at the same time, overnight last night: 32GB iPhone 3GS 16GB iPhone 3G First-generation iPod Touch Kensington Portable Power Pack for Mobile Devices I can't say anything about the charging speed (as I left it overnight) but all devices were fully charged this morning.

  Read the article

< Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >