Search Results

Search found 1910 results on 77 pages for 'voice modem'.

Page 53/77 | < Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >

• Share internet with my phone?

  - by Kenneth Cochran

  Most people want to use their cellphone as a modem for their computer, commonly referred to as 'tethering'. I'm actually interested in doing the opposite: Sharing my landline internet connection(which is much faster than any 3G service) with by cellphone. My phone is a Verizon BlackBerry Curve 8330 and it has USB and bluetooth connections. I know both USB and Bluetooth are capable of supporting tcp/ip traffic what's not so clear is: Is IP over USB or Bluetooth standardized? Is it supported on my phone? Has my cellphone company crippled my phone to prevent me from using it?

  Read the article

• Unexpected network traffic?

  - by robwalker

  My internet connection is via a fixed wireless connection using a 900MHz Motorola Canopy module. The router reports a fairly consistent 32-64Kbps of incoming traffic on the WAN port. When I attached a PC directly to the port and run Wireshark, I get a dump showing a lot of chatter from other machines that I presume are connected to the same tower. This didn't include end-to-end traffic, but was there were a lot of ARP requests, SSDP traffic, ICMP and other network discovery type stuff. Is this 'normal' or does it suggest a misconfiguration somewhere? As far as I can tell there is no need for my modem to be receiving any of this traffic (other than wanting to know what the names of my neighbours machines and printers are!) Since the internet connection is slow at the best of time, having this amount of background noise seems very wasteful.

  Read the article

• Is there a way to submit a batch of commands to a Cisco router and have them execute from the router?

  - by atroon

  I need to change the configuration of a remote (6 hours' drive) client's Cisco 871 (IOS 12.4.15T) from my location because of some new internet service at his location. To be more precise, I need to change the default route, ip address of the outside interface (Fa4) and disable the PPPoE setup there. Unfortunately, doing any of this will (obviously) break the connection to the router. I do not have an out-of-band management modem set up (I know, I know). Is there any way to enter the commands I need to have run and have them execute one after the other, from a file on flash:? I have never tried anything like that before. Essentially a DOS-style batch file is exactly what I need. Nothing like it seems to be out there except using kron to execute CLI commands, but that is specified here as only taking EXEC commands, not configuration ones. Is there hope, or do I travel?

  Read the article

• Netgear Router missing Wireless Configuration Menu Link

  - by ccisystems

  I have a Netgear WiFi router DG834G v3. On it it says it's a WiFi, ADSL 2+ modem, switch, etc. There is an antenna on the back and a WiFi indicator on the front. However, when I connect to it via the web interface, the wireless setup link is missing from the menu. The top label indicates it is a DG834 (without G). I have received it from a friend and was really looking forward to using it but I really need the WiFi part. I looked on Netgear's site as I thought someone must have uploaded the wrong firmware for the device sometime - so I upgraded to the latest firmware, but it still says it's NOT a 'G' device and the wireless menu is nowhere to be found. I'd appreciate a push in the right direction as to what I could do. Is it possible that the WiFi chip is broken or something and the device does not detect it and the firmware reverts the device to a different version?

  Read the article

• Linux Bridge, Samba netbios name/hostname access

  - by Christopher Wilson

  I am currently running a linux bridge in the following configuration ADSL Modem: 192.168.1.1 Linux Bridge: eth0: 192.168.1.2 eth1: no address Wireless Router: 192.168.0.1 My issue is that i cannot access the "Linux Bridge" shares using the WINS name of the server via client systems (yes i understand it is a transparent bridge but i can access it via the 192.168.1.2 address this is not on the same subnet as the client systems). This is the global section of my SMB.CONF [global] unix extensions = off os level = 20 netbios name = server guest account = nobody server string = 447 Server security = share #unix extensions = no #wins support = yes #wins server = 192.168.0.1 name resolve order = wins lmhosts hosts bcast interfaces bridge1 eth0 eth1 lo bind interfaces only = yes Can i access a bridged server using it's WINS name to access samba shares? Cheers Chris

  Read the article

• which vista services can be disabled with impunity?

  - by GwenKillerby

  I use Vista on a HP pavilion DV2 laptop. When I look through all the services my laptop starts, it really seems there's way too much of it. I multi boot with XP and 7. Both startup in 40 seconds. Vista takes four minutes. Is there some software that can determine which services I don't need? On 7, there's no propietary HP stuff at all, yet it seems to run fine. Because all these service, there's a LOT of them and some just sit there doing nothing, monitoring for updates I don't really need or want or need to know about the second they're available. my laptop is the only computer i use at home, there's no home network, aside from the modem-router, which is cabled, not wifi. Take for instance Parental controls, and stuff for people with bad eyesight, Tablet PC. I really never use any of that stuff. Hope this question is specific enough. thanks, Gwen.

  Read the article

• Ubuntu cannot access internet, LAN is fine

  - by Kevin Southworth

  I have an Ubuntu 8.04 LTS server that is directly connected to our Comcast Business Gateway modem and I have configured it with 1 of our 5 allotted Static IPs. My other machines on our LAN can connect to this server (via ssh, web, ping, etc.) but I cannot access this server from outside our network, and this machine cannot get out to the internet either (ping google.com fails with unknown host). Here is my /etc/networking/interfaces file: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 173.162.54.19 netmask 255.255.255.248 broadcast 173.162.54.23 gateway 173.162.54.22 and my /etc/resolv.conf: nameserver 68.87.77.130 nameserver 68.87.72.130 output from sudo route -n: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 173.162.54.16 0.0.0.0 255.255.255.248 U 0 0 0 eth0 0.0.0.0 173.162.54.22 0.0.0.0 UG 100 0 0 eth0 I have a Windows 2008 machine with an almost identical Static IP, static DNS setup and it works correctly, can access it within the LAN and also from public internet, the Windows machine and the Ubuntu machine are both directly connected to the Comcast Business Gateway. I have tried rebooting Ubuntu, rebooting my Comcast modem, but nothing seems to make it work. I'm an Ubuntu noob, is there some other config I need to apply to make this work? UPDATE: Yes I am able to ping my default gateway 173.162.54.22 output of iptables --list -n: Chain INPUT (policy DROP) target prot opt source destination ufw-before-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-input all -- 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy DROP) target prot opt source destination ufw-before-forward all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-forward all -- 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT) target prot opt source destination ufw-before-output all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-output all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-after-forward (1 references) target prot opt source destination LOG all -- 0.0.0.0/0 0.0.0.0/0 limit: avg 3/min burst 10 LOG flags 0 level 4 prefix `[UFW BLOCK FORWARD]: ' RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-after-input (1 references) target prot opt source destination RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:137 RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:138 RETURN tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:139 RETURN tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:445 RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:67 RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:68 LOG all -- 0.0.0.0/0 0.0.0.0/0 limit: avg 3/min burst 10 LOG flags 0 level 4 prefix `[UFW BLOCK INPUT]: ' RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-after-output (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-before-forward (1 references) target prot opt source destination ufw-user-forward all -- 0.0.0.0/0 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-before-input (1 references) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ctstate RELATED,ESTABLISHED DROP all -- 0.0.0.0/0 0.0.0.0/0 ctstate INVALID ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 3 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 4 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 11 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 12 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp spt:67 dpt:68 ufw-not-local all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 224.0.0.0/4 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 224.0.0.0/4 ufw-user-input all -- 0.0.0.0/0 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-before-output (1 references) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW,RELATED,ESTABLISHED ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW,RELATED,ESTABLISHED ufw-user-output all -- 0.0.0.0/0 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-not-local (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 ADDRTYPE match dst-type LOCAL RETURN all -- 0.0.0.0/0 0.0.0.0/0 ADDRTYPE match dst-type MULTICAST RETURN all -- 0.0.0.0/0 0.0.0.0/0 ADDRTYPE match dst-type BROADCAST LOG all -- 0.0.0.0/0 0.0.0.0/0 limit: avg 3/min burst 10 LOG flags 0 level 4 prefix `[UFW BLOCK NOT-TO-ME]: ' DROP all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-user-forward (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-user-input (1 references) target prot opt source destination ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:80 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:22 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-user-output (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0

  Read the article

• Public IP shows strange characters and Facebook registers logged-in session to a different location

  - by Stuart Kershaw

  I'm encountering some IP strangeness today and hoping to find an explanation. In short, I'm based in Seattle, WA with my ISP being Comcast. While browsing Facebook's account settings, I noticed that my active session was located to Mount Laurel, NJ. At that point I ran a search in Google for 'my public IP', which returned an interesting result: a string of characters in the following format: 2601:8:b000:xxx:xxxx:xxxx:xxxx:xxxx Normally, a search for my IP returns something like: 67.xxx.xx.xxx A phone call to Comcast got me nowhere, but using Comcast's phone-menu debugging tools, I was able to send a 'refresh signal' to my modem. After that, the search for 'my public IP' yielded the expected result... for about 5 minutes, and then it returned to the new string of characters. Does anyone know of an explanation for this?

  Read the article

• What's causing "shutdown state" after TFTP reloaded Cisco `running-config` on 871?

  - by xtian

  Cisco CCP Write Configuration borked my 871w config while I was trying to setup port forwarding. I tested the 871's flash memory with fsck and rewrote the minimal config for TFTP (which is the same for Cisco's CCP app.). Thne, I successfully uploaded a previously working running-config from Win Vista using SolarWinds TFTP Server, unfortunately the restore was not entirely successful. The old running config was saved to the 871's startup-config and I can login using console port. Some other things that are working are the hostname and welcome message but that's about it. Startup shows an error SETUP: new interface NVI0 placed in "shutdown" state after tftp. The missing light on the access point modem for ethernet link show the 871'a outside FE4 is not working. SO...what's the possible problem with reloading a previously working config (approximately 4 months with the same config) via TFTP? Is there something I can look for on the 871 to verify the config?

  Read the article

• Does a bad Internet connection increase bandwidth usage?

  - by Synetech

  My (Rogers) cable connection has been pretty bad recently (channels 3 and 10 are particularly fuzzy—it’s analog, not digital cable). Not surprisingly, this has caused my cable modem to drop out and have to reestablish a connection a couple of times since it started. The poor connection of course means higher corruption (not necessarily dropped per se) which causes the TCP/IP stack to have to retransmit packets more often. Reduction of bandwidth throughput aside, I got to wondering if it increases the actual bandwidth usage. That is, if there is a high error rate on the line causing packets to have to be retransmitted: Does this increase a bandwidth monitoring program’s numbers? Does the ISP count the retransmitted packets toward the monthly cap? Based on what I remember from my university networking courses and common sense, I have a feeling that the answer to both questions is yes, but I cannot reliably measure the first, and have no authoritative answer for the second. I’m wondering if maybe the retransmitted packets are acknowledged as being duplicates and thus not counted somewhere along the line.

  Read the article

• Can I set up a 2nd home wireless router, with router2 connecting to the internet through a desktop which is wirelessly connected to router1?

  - by gil b.

  Hi, I apologize for the crudeness of my MSPaint drawing, but please view my diagram of what I'd like to accomplish: Proposed home network architecture Currently, all devices are connected to 1 wireless router. I would like to make my own subnet, with a box in-between my subnet and the shared wireless router, so that I can learn about IDS, traffic analysis, etc. I was also given a cisco PIX firewall to play around with, and it'd be an added bonus if I could incorporate that into my network. The reason for this proposed architecture is so that I can monitor all MY traffic, without seeing anything going on with my roommates' traffic. my MAIN Question is, is it possible to have my desktop connect to the wireless router with internet via wireless card AND share that connection via the ethernet card, hooked to wireless router 2? cable modem - wireless router - desktop pc connected wirelessly - wireless router 2 getting internet from wired connection to desktop pc - laptops connected wirelessly The PIX can be left out for now, but I'm wondering if it could eventually be incorporated? THANKS!

  Read the article

• Netgear VPN can't access specific server

  - by Critologist

  I have a Netgear FVS318N configured with a VPN. I'm trying to access my call recorder with the provided software from another office. I've already setup the VPN connection, and it works. I can connect and ping the remote router and a few other things on the network. However, I can't ping or connect to my call recorder. If I move outside of the office network (i.e. connect directly to the cable modem or via a mobile hotspot), I can connect and ping the call recorder just fine. The office has a simple Linksys WRT54G router and is using AT&T Uverse. The remote location is using Charter Cable with a Netgear FVS318N. Has anyone ever encountered anything like this before? I've setup an identical VPN previously for a different client using similar hardware and never encountered this. Thanks in advance!

  Read the article

• Windows 7 "Could not reconnect all network drives" on boot

  - by Thermionix

  Windows 7 won't reconnect to my network drives on startup. Once it is done booting opening Windows Explorer and clicking each share will mount them. Windows 7 Enterprise N Service Pack 1 I have attempted formatting the windows machine - first thing done to machine was to map the network drives, upon reboot they were disconnected. It is running on an Crucial M4 64gb SSD. The host of the network shares is a Ubuntu-Server machine connected through a gigabit switch. A modem provides dhcp, although both these machines have static IP's defined. It won't reconnect the drives regardless of whether they're SAMBA shares or NFS shares - therefore I believe it's an issue with the windows machine. Ubuntu 11.10 (GNU/Linux 3.0.0-12-server x86_64) I've tried using ip address instead of netbios name for mapping shares on the windows machine, Also tried setting EnableLinkedConnections=1 gpedit.msc Computer Configuration - Administrative Templates - System-Logon - always wait for the network at computer startup and logon = yes

  Read the article

• How to share my localhost over the internet?

  - by Loolooii

  I really want to share my localhost over the internet to show my friends the progress of the website we're working on, so that I don't need to upload it to the public server each time I make a change. showoff.io is not free and localtunnel gives me "failed to authenticate" when trying to upload my public key (a lot of people seem to have this problem and there doesn't seem to be a solution for this). Does anyone know any other free service I can use or any other solution at all? I'm using a Mac. Thanks. UPDATE: with localhost I mean a web server running on my computer, I have a dynamic IP address and no I'm not behind a router (just using a wireless modem).

  Read the article

• Virtual Hosting in RHEL5

  - by Kumar P

  We having RHEL5 linux server with few windows xp clients. We providing web development in php. Now my developers as for common local php server for keep their projects in same place. Currently proxy server and samba sharing are running in RHEL5 server. I installed httpd,php,MySQL in server. And i would like to configure virtual hosting too for LAN. What i want do for it ? In server we have 2 Ethernet ports, 1 for local connection and another one for Internet. Internet provided by ADSL provider. (192.168.0.0 series for ADSL modem connection and 10.1.1.0 for LAN connection. If i want to use virtual hosting , am i want to setup local DNS server ? My requirements are, setup php with mySQL server for Local clients with multiple hosting , without disturbing proxy and samba. Help me to solve it.

  Read the article

• Routing using Linux with 2 NIC cards

  - by Kevin Parker

  Configured Clear OS to be in Gateway mode on a machine with two NIC cards. eth0:192.168.2.0/24 with ip 192.168.2.27 which is connected to a modem and thus have internet connectivity. eth1:192.168.122.0/24 with ip 192.168.122.10 which is connected to other machines in LAN through switch. LAN machines with network 192.168.122.0 is not getting internet.How can they get internet Through Clear OS gateway.I have enabled packet forwarding in clear os using "ip_forward=1" What am i missing?.Can you please help me in this. Following are the static routing i have added: on LAN machine1 with ip address 192.168.122.11 ip route add 192.168.2.0/24 via 192.168.122.10 dev eth0 ip route show 192.168.2.0/24 via 192.168.122.10 dev eth0 192.168.122.0/24 dev eth0 proto kernel scope link src 192.168.122.11 But still 192.168.2.0/24 network is not reachable.Where can be the problem??

  Read the article

• Credentials needed for BT line on Netgear router

  - by Bali C

  I have recently bought a new Netgear router to replace my current BTHomeHub as it doesn't support wireless. I did buy a WAP but figured it would be easier to use a router with wireless built in. (It's a modem/router combo). I have got as far as setting up the router on the web interface, but then it asks for a username and password to connect to the net, I can only assume this is for the phone line? I have tried some passwords I could find written down but they don't work, the internet light comes on and then when the creds fail it goes off. I have been on the homehubs web interface and been through all the settings it has to find the credentials it is using which obviously work, but no joy. Is there anything obvious I am missing, or is there a way I can retrieve my settings from my existing router? Any pointers will be very appreciated.

  Read the article

• Disconnected from WiFi, Windows claims otherwise [closed]

  - by Manu

  I'm connected via wifi to my ISP's router/modem. While Windows says that I'm always connected, I keep getting messages from Netgear Genie that I've lost contact to the Internet, and I cannot access webpages until it comes back. There are two other computers in the house, one connected to the router via ethernet, the other via wifi, both seem to have no such problems. I've wondered if Netgear genie itself was the problem, but I am regularly disconnected even if I uninstall it. And I'd rather have it since it accurently tells me if I'm connected or not. Why does windows says I'm online if I can't access any online game, or website ? I've removed the connection, recreated it, I've even copied the settings to a usb key from the computer that has wifi access. Is there a tool that can tell me which program, if any, is disconecting me ?

  Read the article

• Configuration of Home Network

  - by Wen Jie

  Previously my home network is as follows Speedtouch ST536 -> Linksys WRT54G But now as I have upgraded my internet subscription. My service provider gave me a "2Wire 2701 HGV" modem. I was wondering if it is possible to put the "2Wire" as an access point. So I might have a configuration as follows? Room Living Room Speedtouch ST536 -> Linksys WRT54G {Wireless} 2Wire 2701 HGV Because I find that my signal is very weak. Is there any way for me to do that?

  Read the article

• Router loses connection to internet randomly

  - by tvanover

  I have a Belkin wireless G plus Mimo router and it randomly loses the connection to the internet. It seems to happen for a second or two, not enough to impact day to day browsing. But enough to disconnect games, or stall videos I am watching. It happens whether I am plugged into the router or connecting via wifi. I am unsure if it is my router or Comcast that is causing this issue. If I connect a computer directly to the modem the problem never occurs, so that tells me it is probably the router. But I also had a Netgear wireless router WGR614, and it had the same problem. I don't know where to start looking for the source of the problem. What logs should I be combing through? All my machines are win 7 of varying versions.

  Read the article

• Trouble with resolving hostnames on CentOS using Bind

  - by cabaret

  I'm taking a course on server administration at school and I have managed to set up virtual hosting in apache and a dns server on a virtual machine. However, I have now set up an old pc to run CentOS and I'm trying the same on that box. The problem I ran into now is that I can't resolve hostnames from the linux box. I have set up the nameserver in /etc/resolv.conf to the IP of the CentOS machine, but when I try for example ping google.com I get ping: unknown host google.com However, when I do ping 66.102.13.105 (which is the Google IP, figured that out by pinging on my mac) I get: PING 66.102.13.105 (66.102.13.105) 56(84) bytes of data. 64 bytes from 66.102.13.105: icmp_seq=1 ttl=52 time=15.5 ms Slightly confused why this is happening. Could it be because of my router sitting in between the linux machine and the cable modem? It's a D-Link somethingsomething. Thanks in advance

  Read the article

• Can't find a wireless access point's IP address after changing router IP/LAN settings

  - by flagg19

  I have a modem/router, Netgear DG834, and a wireless access point (AP), Netgear WG602. The AP is directly connected to the router. My old working configuration was: Router IP address : 192.168.0.1 Access point IP address: 192.168.0.10 My new configuration is: Router IP address : 192.168.1.1 Access point IP address: ???.???.???.??? I changed my router's IP address/LAN settings to set up a VPN with another Netgear router that had the same LAN configuration. The wireless network is still up and perfectly working, but I can't find the AP's IP address. I've tried broadcast ping but the AP won't respond. I looked at the router "attached devices", but it's not there. I've played around with Nmap and arp request but the AP is totally invisible. I can fix it by resetting it to factory settings, but I'm very interested in learning more about this problem. I'm also interested in network security and this fact of having an invisible AP well, it's something I'd like to understand.

  Read the article

• Prevent users from Router 2 seeing Router 1 computers

  - by Patrick Robert Shea O'Connor

  I've got 2 Netgear N300 (WNR2000v3) routers. Here's my setup: Modem Router 1 Private Users/Router 2 Public Wireless Users on "Guest" Network. I want to prevent users who are connected to Router 2's "Guest" network from accessing anything that is connected to Router 1. There is an option when setting up the "Guest" network called "Allow guest to access My Local Network" which I thought if unchecked would do this very thing; however, I can still access files and such of computers connected to Router 1. Router 1 assigns 192.0.0.x IP addresses, Router 2 assigns 10.0.0.x IP addresses, how can they even see each other? Do I need to change the subnet or something else?

  Read the article

• Connect macbook to my LAN through a VPN - best solution?

  - by LewisMc

  So I have a LAN connected via a ADSL/PPPoA, this is using a bog-standard DLink router supplied by my ISP (talktalk UK). I have a NAS within the LAN that is running FreeNAS and I want to be able to connect to it when I'm out and about. It's running an atom so it's quite low on juice consumption but I don't want to have it on all day and night so I've been waking it via a magic packet and booting it down from the web admin when I need it. So I want to connect to the LAN, I presume via a VPN, to be able to send a magic packet. But what is the best method to accomplish this, or is there an easier way? I've been looking at the cisco 857 integrated router and the Netgear prosafe 318(behind modem) but not sure If I'm on the right track with what I want to achieve as I've not much experience or knowledge with VPN's or networking (software engineering student). I have tried port forwarding but to no avail, either with magic packets or even connecting outside the LAN via DYNDNS. Thanks,

  Read the article

• Wireless is connected but no internet when PC Turns on

  - by mhesabi

  I have a PC that is connected to ADSL Modem router (linksys WAG54g2) directly via Ethernet cable And a laptop and also other devices such as another laptops and smarth phones. However when I turn On the PC or turn it off, some strange problem happens. My wireless network seems connected on laptop but there is no internet activity and can't open a webpage until I turn router off and on again manually. (other devices including the PC itself can't use the internet either) My router configured this way: Encapsulation: RFC 2516 PPPoE Multiplexing: LLC DHCP Server: Enabled and network sharing center IPv4 configuration is obtain IP address automatically How Can I fix this issue?

  Read the article

< Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >