Search Results

Search found 21319 results on 853 pages for 'state management'.

Page 534/853 | < Previous Page | 530 531 532 533 534 535 536 537 538 539 540 541  | Next Page >

• Clicks or ticks every minute when HDD is idle [closed]

  - by Ramy

  Possible Duplicate: Clicks or ticks every minute when HDD is idle My HDD is a My passport... It's 2 weeks old. I hear this tick or click followed by another one about 8-9 secs later, and they repeat every minute almost exactly... They usually happen and the LED light blinking.. It's not like the other clicks you hear that indicate any inevitable HDD failure, it's much lower in volume. I don't know what that is, however it's different than the rest of the HDD usual sounds...It's close to the sound of the mouse click. It sometimes also happens when I access a file on the drive mostly after being idle for a while, sometimes randomly not really sure... The drive though is working well, the SMART report comes out OK and without warning, and disk management shows it healthy... What could be the cause of this??

  Read the article

• VMWare guest OS is not using full hard drive space

  - by syuusuke

  Hey everyone, I'm wondering if you can give me some insight on how to figure this out. I've recently virtualized a w2k3 server that had 10GB C:\ drive size. Once I finished virtualizing it, I expanded the disk to 20GB for C:\ and within guest OS (W2K3) computer management settings, you can see it recognizes as 20GB partition C:. But for some reason, if I opened windows explorer and see the properties of C:\, it will only show total size of 10GB. Does anyone know how to solve this or even had this problem before?

  Read the article

• Login sometimes failing immediately after restoring a database

  - by Ian Ringrose

  We have a set of automated tests that restore a database then run some .net code against the database. Sometimes after the database is restored the login from Ado.net fails. If I re-run the test, then the restore and login works OK. The restored database looks OK when viewed with Management Studio. This is only an problem on some machines. We are using SQL server 2008. Is there a known issue with a database restore “returning “ a very short time before the restored database is up and running.

  Read the article

• Limit number of simultaneous connections squid makes to a single server

  - by Ben Voigt

  Note: I am asking about outbound concurrent connection limits, not inbound, which is sufficiently covered on existing questions Modern browsers typically open a large number of simultaneous connections, to take advantage of the fact that TCP fairly shares bandwidth between connections. Of course, this doesn't result in fair sharing between users, so some servers have started penalizing hosts which open too many connections. This limit can be configured client-side (e.g. IE MaxConnectionsPerServer, Firefox network.http.max-connections-per-server), but the method differs for each browser and version, and many users aren't competent to adjust it themselves. So we turn to a squid transparent HTTP proxy for central management of HTTP download. How can the number of simultaneous connections from squid to a remote webserver be limited, so the webserver doesn't perceive it as abuse of concurrent connections? Ideally the limit would be per source address. Squid should accept virtually unlimited concurrent requests from the client browser, and issue them sequentially to the remote server, only N at a time, delaying (but not dropping) the others.

  Read the article

• How to setup Wordpress High Availability

  - by Ketam

  I have installed Galera Cluster on 3 cluster + 1 management. I wanted to make it like this, Server1: Home (www.domain.com) Server2: For BBpress/Forum (Forum Tab Menu will forward to forum.domain.com) Server3: BuddyPress Activity (Social Tab Menu will forward to social.domain.com) The purpose I am doing this is to distribute my resource and load balancing each other at same time. However, I have difficulty to setup Apache Load-Balancing/mod_proxy/clustering or any suitable to have high availability WordPress. Any best suggestion/solution to make high availability WordPress? Or how to? And another question is I tried to copy whole WordPress files & folders to Server2 connecting to local database (same data inside since it is already on Galera Cluster) but the page blank. Any advice? OS: Centos 6.2 Thanks in advanced.

  Read the article

• Hyper-V Guests suddenly stopped working

  - by Anton Gogolev

  Hi! Here's my configuration: Windows Server 2008 R2 Standard as a host OS, and two guests VMs running the same exact OS. Yesterday, Trial Activation on all OSes has expired and quite naturally all machines shut down. I rearmed the host, but cannot log on to either guest VMs. From what I see, they start up normally (State is listed as Running) but CPU Usage seems to be stuck at 3% and when I connect to it all I see is black textmode screen with cursor blinking. One of my VMs has several snapshots, and when I revert back, it starts up normally. Moreover, "reference VM" (the one I cloned these two VMs from) starts up just normally. How can I troubleshoot this issue?

  Read the article

• How to factory reset an EPSON Stylus Photo 1290 printer?

  - by Harry Wood

  How do I do factory reset on an EPSON Stylus Photo 1290 printer? The printer is refusing to work. It seems to be in some error state. I've tried re-installing drivers etc, but the printer itself seems to run some diagnostic routine when I switch it on, but will not do anything else. It will not move the carousel ready for me to change the printer cartridge or any other Is there'e some sequence of button presses on the printer to do a factory reset? The printer has three buttons on the front, plus a yellow button when the hood is open (as shown in this photo)

  Read the article

• Need help connecting to SRW2024 Linksys Switch from CentOS 5.4

  - by sxanness

  I am configured a Linksys SRW2024, I accidently changed the management VLAN before changing the VLAN configuration thus I can no longer access it with the net. The only way I have read to get into it now is via a console cable, my laptop with me is a MacBook Pro with no Serial port connection, apart from driving around a town that I am unfamilar with to find an adapter I thought I would try on a Linux box. I have a CentOS 5.4 server here (PowerEdge R300) that I am trying to use to talk to the switch. I tried minicom first but I do not see the console. Another site suggested the screen command. I tried "screen /dev/ttyS0 38400" but all I get is blinking curser, I do not see the configuration. I don't know if anyone here as any tips but I hope someone does. Thank You,

  Read the article

• Performance issues with new dedicated server [closed]

  - by Pierre Espenan

  I have just subscribed to a new dedicated server and am getting worst than expected PHP execution performance. Execution times are twice as high as on my old mutualized server! I'm definitely not an expert at server management, so I'm wondering what I missed. Here are some stuff that can help you understand what's wrong here : My server (in french but easy to understand) : http://www.online.net/fr/serveur-dedie/dedibox-sc phpinfo(); output : http://jsfiddle.net/E8b7W/embedded/result/ PHP bench script (dedicated server) : http://jsfiddle.net/EhXzK/embedded/result/ PHP bench script (old mutualized) : http://jsfiddle.net/ANbWt/embedded/result/ Is it normal to get such poor performances after a kernel update and basics "apt-get install" for apache2 and php ? Thanks !

  Read the article

• Hp Procurve Switch : port filtered

  - by user117140

  My HP Procurve switch is blocking port 22 and I dont know how to unblock it.Please let me know From the server, see port 22 is blocked [root@server ~]#nmap -p22,80,443 10.247.172.70 Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2012-04-16 14:12 IST mass_dns: warning: Unable to determine any DNS servers. Reverse DNS is disabled. Try using --system-dns or specify valid servers with --dns_servers Interesting ports on 10.247.172.70: PORT STATE SERVICE 22/tcp filtered ssh ------------------> see 80/tcp filtered http 443/tcp filtered https This is blocked on cisco switch but I dont have any clue how this is done. I know that vlan is configured on switch. vlan 54 ip ospf 10.247.172.65 area 0.0.0.10 vrrp vrid 54 owner virtual-ip-address 10.247.172.65 255.255.255.192 priority 255 enable exit exit Please let me know how to unblock ssh port 22 access on this switch?

  Read the article

• How to prevent Windows Home server waking for backup

  - by Andronicus

  Since changing the motherboard in my Windows home server it has been switching itself on every night to perform a scheduled backup. I don't want this to happen though, I want to switch the server on using Wake on lan, but I want to manually perform backups if/when required. I know I can disable backups of each computer, and the machine wont turn on, but I want to allow manually triggered backups, or automatic backups if the homeserver is on, but if its in sleep mode, I wish it to stay in that state unless I wake it. How can this be achieved?

  Read the article

• New Session Failed

  - by PhilPursglove

  We've started to see instances on our Intranet server where for any page the server just responds with the error page 'HTTP/1.1 New Session Failed'. It seems we can fix it by running IISRESET but this feels like we're only treating the symptom. The server is a virtualised server running IIS6 on Windows Server 2003 with 0.5Gb of RAM. Our Intranet is written in ASP, but we also have ASP.NET 2.0 applications running on the web site. The site is set up for Anonymous and Integrated Authentication. What causes IIS to get into this error state? Could the server be saturated with requests i.e. we need to scale out and move some applications onto another server? I've seen KB210842 but I'm not sure it applies as that is applicable to IIS 4

  Read the article

• Installing Java 6 on Ubuntu 10.04 fails on missing Java 6 JRE package

  - by David S

  I'm trying to install Java 6 on Ubuntu 10.04 and it's been harder than it should be. In another question about installing Java on Ubuntu/Linux it said that I needed to do the following: sudo add-apt-repository "deb http://archive.canonical.com/ lucid partner" However, that failed and I kept getting: sudo: add-apt-repository: command not found The solution to this, was to run: sudo apt-get install python-software-properties So, that seemed to work and the command above to "add-apt-repository" seems to complete with no errors. And I have run the following to confirm it got added. sudo vi /etc/apt/sources.list But, now when I run the following: sudo apt-get install sun-java6-jre I get: Reading package lists... Done Building dependency tree Reading state information... Done Package sun-java6-jre is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package sun-java6-jre has no installation candidate Where do I go from here?

  Read the article

• Cisco 1841 Box and Watchguard XTM21-W

  - by Corey

  I have never set one of these up before and need a little assistance. Right now we have a T1 line coming in from Sprint to a Cisco 1841 and then on to our router. However, when I plug the Cisco 1841 into Port 0 and the router into Port 3 it does not work. In Port 1 I have my management computer plugged in. We have one subnet and this must be easy but I cannot figure out how to make this work. When the firewall is plugged in then I get no internet or network access.

  Read the article

• USB sector 0 not fount Kingston USB DT100 G2

  - by java

  Windows constantly asks me "Foramt Disk". when i go to command prompt and type format H: /fs:ntfs or format H: /fs:fat32 response: Cannot determine the number of sectors on this volume. if the benefit DISKPART detail disk Kingston DT 100 G2 USB Device Disk ID: 00000000 Type : USB Status : Online Path : 0 Target : 0 LUN ID : 0 Location Path : UNAVAILABLE Current Read-only State : No Read-only : No Boot Disk : No Pagefile Disk : No Hibernation File Disk : No Crashdump Disk : No Clustered Disk : No DISKPART detail volume Read-only : No Hidden : No No Default Drive Letter: No Shadow Copy : No Offline : No BitLocker Encrypted : No Installable : No Volume Capacity : 0 B Volume Free Space : 0 B what the problem?

  Read the article

• How Can I prevent a specific application from being run on a specific machine using Group Policy?

  - by Mike

  I know this is possible to do and I am working on it with limited success. I believe the Group Policy I want is "Do Not Run Specified Windows Applications" - I can enable this and add the .exe I want to the list of programs not to be run. I have tried this on my local machine by running gpedit.msc going to User Config Admin Templates System and then choosing that policy and editing and enabling it. Doing it this way verifies that it works as I could then not run the specified .exe (XenAppWeb.exe) So this is great. I have created a GPO to do the same thing in GP Management on my domain controller where we centralize this, enforced it, applied it to an OU, and put one of our machines into this OU to test it. I have let it sit there for 3 days, run gpupdate /force, and when I try to run XenAppWeb.exe on this machine, it still lets me run it fine. What can I look at to troubleshoot this? I should note that I am trying to enact this policy on Windows XP machines (Virtual Machines) Thanks, Mike

  Read the article

• How do I upgrade Django 1.3.1 to 1.4? Any tips, tutorials, or warnings?

  - by hobbes3

  Django 1.4 was recently released. Almost all the information about Django 1.4 is in the release note, but I didn't see anything about how to upgrade. Should I just remove the django folder inside Python's site-packges and download 1.4? I think I originally installed Django using emerge and yum but I'm not sure if the package management systems are up-to-date with Django 1.4 yet. That might be ok on my server instance (Gentoo Linux), but on my local instance I am using virtualenvwrapper (on Mac OS 10.7), so maybe I want to create a new Python virtual environment for Djago 1.4. Or maybe not since I don't really care about backward compatibility with 1.3.1.

  Read the article

• Is there an way to get the top level classes included in a puppet node?

  - by pwan

  Is there an easy way to return the top level classes applied to a node. By this I mean the classes included in a node definition or ENC equivalent For example with the sample node below, I'd like to return 'return::me' and 'return::me2' for somehost, but not 'dontreturn::me' class return::me { include dontreturn::me } node "somehost" { include return::me include return::me2 } I see that /var/lib/puppet/state/classes.txt includes the full list of classes applied to the node, but that includes any additional classes included by to the top level classes. Is there some way to get at this data with a puppet faces command ? I suspect 'puppet nodes' might be useful, but I haven't been able to get it return what I what.

  Read the article

• Windows 2008 additional disk going offline with reboots on Amazon EC2

  - by Ernest Mueller

  OK, so I took the stock Windows 2008 64-bit Amazon AMI and wanted to add a D: drive for page file space and crash dumps. I launched the instance with a second EBS volume attached as xvdf and went into Disk Management set it online, and added the page file and crash dump settings and all that works. But when I reboot, the box comes back up with that second drive as "Offline." How do I get that disk to automatically come online on reboot (or most notably, when I turn this into an AMI and launch more instances off it - I've tried that too and same deal with the D:).

  Read the article

• Homegroup and NTFS permissions

  - by bytenik

  I'm running a copy of Windows 7 as a "server" at my home. I have several file shares that I want to make available to specific users only. I've modified the NTFS permissions to only allow these users to access their respective shares. However, while a locally logged on user can access the actual folders just fine, over the network the remote access is authenticating as HomeGroupUser$ rather than the actual user in question, as shown by the Computer Management panel for shares. I do have matching user accounts (i.e. my username locally is abc and a parallel account with username abc and the same password exists on the server machine). I don't want to disable homegroup because there are other shares where homegroup authentication would be desirable, especially for some people where they don't have a parallel account. Is there a way to get the system to authenticate first by matching username, and then by homegroup authentication if there's no matching user?

  Read the article

• OSX Lion - Stuck in Drag mode and mouse click events are not going through. Can I manually generate a mouseup event?

  - by Yuji Tomita

  My mouse is stuck in "drag" mode. This generally happens in Photoshop, but happens dragging files and such as well. Clicking rapidly here and there generally solves the problem. Sometimes though, it won't go away until a restart. Unplugging devices, etc., doesn't do anything. For example, right now, my mouse moves but can not click anything so I am using the keyboard to navigate this site. Is there a way to "reset" however the OS stores mouse states? Can I manually fire off a MouseUp event? It's strange that even when human input devices are unplugged, the files are still in drag state.

  Read the article

• OpenVPN Permission Denied Error

  - by LordCover

  I am setting OpenVPN up, and I'm in the state of adding users. Details: Host System: Windows Server 2003 32-bit. Guest System: Ubuntu Linux (with OpenVPN installed already), actually I downloaded it from OpenVPN.Net. Virtualization: VMWare v7.0 Problem: I can access the Access Server web portal (on the port 5480), but when I login to http://host_ip:943/admin and enter my (correct) login info, it shows me a page saying that "You don't have enough permissions". I am the (root) user!!!! that is really weird!!! Note: if I enter wrong login it will denote an incorrect login, this means that I am logging in successfully but the problem comes after the login process. What I tried: I tried to create another user after (root) logging in to Linux Bash using (useradd) command, but the same resulted.

  Read the article

• What does an ACPI BIOS configure during boot?

  - by RJSmith92

  When a PC boots with an ACPI BIOS, what does it exactly do? I understand that the point of ACPI is to allow the OS to control hardware resources and power management but before the OS is loaded does ACPI configure just the devices needed to boot and then let the OS configure the rest? If the OS wants to re-asign hardware resources does it store this information in the ACPI tables so that the next time the system is booted it assigns them how the OS wants? The ACPI driver asks the PCI bus driver (Pci.sys) to enumerate devices on it's bus once the OS is loaded, how are these devices configured whilst the PC is booting when it doesn't have other bus drivers? Any help with any of the above questions would be greatly appreciated. Thanks.

  Read the article

• Web Filter For Multiple Networks

  - by Rob

  I have been using a Barracuda web filter 310 in our network and I have just had enough of it. It does not support trunking and we have several networks that have users that need to be web filtered. (I guess if everyone just did their flippin jobs I would not have this issue) but the management wants me to get it resolved. Does anyone know the top five web filters that are better than the barracuda web filters that support network trunking so that I can have multiple domains and subnets going through it? Thanks in advance - everyone on this site is gold in my book!

  Read the article

• Hard Drive Fundamentals And Verifying Disk Performance

  - by Agnel Kurian

  Over the past few months, my Windows XP machine has slowed down to a crawl. It takes about 10-15 minutes to go from power-up to reaching a responsive state. I have reasons to believe that this is a result of the hard disk slowing down. Questions: Do hard disks slow down as a result of mechanical wear and tear ...or age? How do I check if my disk has slowed down? Conversely, how can I verify that my disk is indeed running at the speed it's designed to run at? Could drivers be at fault here? Do hard disks come with drivers or does Windows use a generic driver?

  Read the article

< Previous Page | 530 531 532 533 534 535 536 537 538 539 540 541  | Next Page >