Search Results

Search found 13776 results on 552 pages for 'password reset'.

Page 535/552 | < Previous Page | 531 532 533 534 535 536 537 538 539 540 541 542  | Next Page >

• Installing multiple php versions plus extensions on freebsd

  - by jgtumusiime

  I'm a currently learning how to work with freebsd. Lately I have been trying to run multiple php versions along with their respective packages. However, I seem to be running into issues while making installations. The default location for my php installation is /usr/local/etc/, however I want to be able to install php5.2, php5.3 and php5.4 in /usr/local/etc/php52, /usr/local/etc/php53 and /usr/local/etc/php54 respectively. Using ports I simply achieved this by doing cd /usr/ports/lang/php5x && make PREFIX="/usr/local/etc/php5x" install clean. The problem now is: How do I do the same for extensions of all my PHP versions? When I try installing php-extensions like so: cd /usr/ports/lang/php5x-extension && make PREFIX="/usr/local/etc/php5x/lib/php" install clean, I get this error ... ===> PHPizing for php53-bcmath-5.3.17 env: /usr/local/bin/phpize: No such file or directory *** Error code 127 Stop in /usr/ports/math/php53-bcmath. *** Error code 1 Stop in /usr/ports/lang/php53-extensions. My PHPize is located in /usr/local/etc/php5x/bin/phpize So how do I get make or whatever to look for phpize in the right path? Is there a cleaner, may be simpler way of maintaining multiple php installations? I need to achieve this because of compatibility issues from some legacy code that runs on 5.2 and breaks on 5.3. Thank you. ================= So I successfully installed an configured freebsd jail and I would like to install software within my jail but I cannot connect to the network. Here is my rc.conf jail_enable="YES" # Set to NO to disable starting of any jails jail_list="mambo2" # Space separated list of names of jails jail_mambo2_rootdir="/usr/jails/j01" # jail's root directory jail_mambo2_hostname="mambo2.ug" # jail's hostname jail_mambo2_ip="192.168.100.174" # jail's IP address jail_mambo2_devfs_enable="YES" # mount devfs in the jail jail_mambo2_devfs_ruleset="mambo2_ruleset" # devfs ruleset to apply to jail here is my jail ifconfig output mambo2# ifconfig rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 00:c1:28:00:48:db media: Ethernet autoselect (100baseTX <full-duplex>) status: active plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST,NEEDSGIANT> metric 0 mtu 1500 lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 mambo2# I created a /etc/resolv.conf for nameservers mambo2# cat /etc/resolv.conf nameserver 192.168.100.251 nameserver 8.8.8.8 mambo2# Here is a list of jails running [root@mambo /usr/home/jtumusiime]# jls JID IP Address Hostname Path 5 192.168.100.174 mambo2.ug /usr/jails/j01 my host has 4 ip addresses, 3 public and one private: 192.168.100.173 I tried creating a jail using ezjail and this does not work out. [root@mambo /usr/home/jtumusiime]# ezjail-admin update -p -i Error: Cannot find your copy of the FreeBSD source tree in . Consider using 'ezjail-admin install' to create the base jail from an ftp server. [root@mambo /usr/home/jtumusiime]# I have an updated copy of freebsd 7.1 source in /usr/src/ and I did #make buildworld while building the first jail mambo2 Here is an excerpt of ouput of ezjail-admin install ... 221 Goodbye. Trying 193.162.146.4... Connected to ftp.freebsd.org. 220 ftp.beastie.tdk.net FTP server (Version 6.00LS) ready. 331 Guest login ok, send your email address as password. 230 Guest login ok, access restrictions apply. Remote system type is UNIX. Using binary mode to transfer files. 200 Type set to I. 550 pub/FreeBSD-Archive/old-releases/i386/7.1-RELEASE/base: No such file or directory. 221 Goodbye. Could not fetch base from ftp.freebsd.org. Maybe your release (7.1-RELEASE) is specified incorrectly or the host ftp.freebsd.org does not provide that release build. Use the -r option to specify an existing release or the -h option to specify an alternative ftp server. Querying your ftp-server... The ftp server you specified (ftp.freebsd.org) seems to provide the following builds: Trying 193.162.146.4... total 10 drwxrwxr-x 13 1006 1006 512 Feb 20 2011 8.2-RELEASE drwxrwxr-x 13 1006 1006 512 Apr 10 2012 8.3-RELEASE lrwxr-xr-x 1 1006 1006 16 Jan 7 2012 9.0-RELEASE -> i386/9.0-RELEASE drwxrwxr-x 7 1006 1006 1024 Feb 19 2012 ISO-IMAGES -rw-rw-r-- 1 1006 1006 637 Nov 23 2005 README.TXT drwxrwxr-x 5 1006 1006 512 Nov 2 02:59 i386 I do not want to upgrade my freebsd installation. I have googled around; but all on vail

  Read the article

• Cisco PIX 8.0.4, static address mapping not working?

  - by Bill

  upgrading a working Pix running 5.3.1 to 8.0.4. The memory/IOS upgrade went fine, but the 8.0.4 configuration is not quite working 100%. The 5.3.1 config on which it was based is working fine. Basically, I have three networks (inside, outside, dmz) with some addresses on the dmz statically mapped to outside addresses. The problem seems to be that those addresses can't send or receive traffic from the outside (Internet.) Stuff on the DMZ that does not have a static mapping seems to work fine. So, basically: Inside - outside: works Inside - DMZ: works DMZ - inside: works, where the rules allow it DMZ (non-static) - outside: works But: DMZ (static) - outside: fails Outside - DMZ: fails (So, say, udp 1194 traffic to .102, http to .104) I suspect there's something I'm missing with the nat/global section of the config, but can't for the life of me figure out what. Help, anyone? The complete configuration is below. Thanks for any thoughts! ! PIX Version 8.0(4) ! hostname firewall domain-name asasdkpaskdspakdpoak.com enable password xxxxxxxx encrypted passwd xxxxxxxx encrypted names ! interface Ethernet0 nameif outside security-level 0 ip address XX.XX.XX.100 255.255.255.224 ! interface Ethernet1 nameif inside security-level 100 ip address 192.168.68.1 255.255.255.0 ! interface Ethernet2 nameif dmz security-level 10 ip address 192.168.69.1 255.255.255.0 ! boot system flash:/image.bin ftp mode passive dns server-group DefaultDNS domain-name asasdkpaskdspakdpoak.com access-list acl_out extended permit udp any host XX.XX.XX.102 eq 1194 access-list acl_out extended permit tcp any host XX.XX.XX.104 eq www access-list acl_dmz extended permit tcp host 192.168.69.10 host 192.168.68.17 eq ssh access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 192.168.68.0 255.255.255.0 eq ssh access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 192.168.68.0 255.255.255.0 eq 5901 access-list acl_dmz extended permit udp host 192.168.69.103 any eq ntp access-list acl_dmz extended permit udp host 192.168.69.103 any eq domain access-list acl_dmz extended permit tcp host 192.168.69.103 any eq www access-list acl_dmz extended permit tcp host 192.168.69.100 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.100 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.101 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.101 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.104 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.104 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.69.104 eq 8080 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.69.104 eq 8099 access-list acl_dmz extended permit tcp host 192.168.69.105 any eq www access-list acl_dmz extended permit tcp host 192.168.69.103 any eq smtp access-list acl_dmz extended permit tcp host 192.168.69.105 host 192.168.68.103 eq ssh access-list acl_dmz extended permit tcp host 192.168.69.104 any eq www access-list acl_dmz extended permit tcp host 192.168.69.100 any eq www access-list acl_dmz extended permit tcp host 192.168.69.100 any eq https pager lines 24 mtu outside 1500 mtu inside 1500 mtu dmz 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 static (dmz,outside) XX.XX.XX.103 192.168.69.11 netmask 255.255.255.255 static (inside,dmz) 192.168.68.17 192.168.68.17 netmask 255.255.255.255 static (inside,dmz) 192.168.68.100 192.168.68.100 netmask 255.255.255.255 static (inside,dmz) 192.168.68.101 192.168.68.101 netmask 255.255.255.255 static (inside,dmz) 192.168.68.102 192.168.68.102 netmask 255.255.255.255 static (inside,dmz) 192.168.68.103 192.168.68.103 netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.104 192.168.69.100 netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.105 192.168.69.105 netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.102 192.168.69.10 netmask 255.255.255.255 access-group acl_out in interface outside access-group acl_dmz in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.97 1 route dmz 10.71.83.0 255.255.255.0 192.168.69.10 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute dynamic-access-policy-record DfltAccessPolicy no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet 192.168.68.17 255.255.255.255 inside telnet timeout 5 ssh timeout 5 console timeout 0 threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp ! service-policy global_policy global prompt hostname context Cryptochecksum:2d1bb2dee2d7a3e45db63a489102d7de

  Read the article

• postfix relaying all mail through office365 problems

  - by amrith

  This is a rather long question with a long list of things tried and travails so please bear with me. The summary is this. I am able to relay email from ubuntu through office365 using postfix; the configuration works. It only works as one of the users; more specifically the user who authenticates against office365 is the only valid "from" More details follow. I have a machine in Amazon's cloud on which I run a bunch of jobs and would like to have statuses mailed over to me. I use office365 at work so I want to relay mail through office365. I'm most familiar with postfix so I used that as the MTA. Configuration is ubuntu 12.04LTS; I've installed postfix and mail-utils. For this example, let me say my company is "company.com" and the machine in question (through an elastic IP and a DNS entry) is called "plaything.company.com". hostname is set to "plaything.company.com", so is /etc/mailname On plaything, I have the following users registered alpha, bravo, and charlie. I have the following configuration files. alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all inet_protocols = ipv4 mailbox_size_limit = 0 mydestination = plaything.company.com, localhost.company.com, , localhost myhostname = plaything.company.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relayhost = [smtp.office365.com]:587 sender_canonical_maps = hash:/etc/postfix/sender_canonical smtp_sasl_auth_enable = yes smtp_sasl_password_maps = hash:/etc/postfix/sasl_passwd smtp_sasl_security_options = noanonymous smtp_sasl_tls_security_options = noanonymous smtp_tls_CAfile = /etc/ssl/certs/ca-certificates.crt smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes As the machine is called plaything.company.com I went through the exercise of registering all the appropriate DNS entries to make office365 recognize that I owned plaything.company.com and allowed me to create a user called [email protected] in office365. In office365, I setup [email protected] as having another email address of [email protected]. Then, I made the following sender_canonical [email protected] [email protected] I created a sasl_passwd file that reads: smtp.office365.com [email protected]:123456password123456 let's just say that the password for [email protected] is 1234...456 With all this setup, login as alpha and mail [email protected] Cc: Subject: test test and the whole thing works wonderfully. email gets sent off by postfix, TLS works like a champ, authenticates as daemon@... and [email protected] in Office365 gets an email message. The issue comes up when logged in as bravo to the machine. sender is [email protected] and office365 says: status=bounced (host smtp.office365.com[132.245.12.25] said: 550 5.7.1 Client does not have permissions to send as this sender (in reply to end of DATA command)) this is because I'm trying to send mail as bravo@... and authenticating with office365 as daemon@.... The reason it works with alpha@... is because in office365, I setup [email protected] as having another email address of [email protected]. In Postfix Relay to Office365, Miles Erickson answers the question thusly: Don't send mail to Office365 as a user from your Office365-hosted e-mail domain. Use a subdomain instead, e.g. [email protected] instead of [email protected]. It wouldn't hurt to set up an SPF record for services.mydomain.com or whatever you decide to use. Don't authenticate against mail.messaging.microsoft.com as an Office365 user. Just connect on port 25 and deliver the mail to your domain as any foreign SMTP agent would do. OK, I've done #1, I have those records on DNS but for the most part they are not relevant once Office365 recognizes that I own the domain. Here are those records: CNAME records: - msoid.plaything.company.com - autodiscover.plaything.company.com MX record: - plaything.company.com (plaything-company-com.mail.protection.outlook.com) TXT record: - plaything.company.com (v=spf1 include:spf.protection.outlook.com -all) I've tried #2 but no matter what I do, office365 just blows away the connection with "not authenticated". I can try even a simple telnet to port 25 and attempt to send and it doesn't work. 250 BY2PR01CA007.outlook.office365.com Hello [54.221.245.236] 530 5.7.1 Client was not authenticated Connection closed by foreign host. Is there someone out there who has this kind of a configuration working where multiple users on a linux machine are able to relay mail using postfix through office365? There has to be someone out there doing this who can tell me what is wrong with my setup ...

  Read the article

• Three ways to upload/post/convert iMovie to YouTube

  - by user44251

  For Mac users, iMovie is probably a convenient tool for making, editing their own home movies so as to upload to YouTube for sharing with more people. However, uploading iMovie files to YouTube can't be always a smooth run, I did notice many people complaining about it. This article is delivered for guiding those who are haunted by the nightmare by providing three common ways to upload iMovie files to YouTube. YouTube and iMovie YouTube is the most popular video sharing website for users to upload, share and view videos. It empowers anyone with an Internet connection the ability to upload video clips and share them with friends, family and the world. Users are invited to leave comments, pick favourites, send messages to each other and watch videos sorted into subjects and channels. YouTube accepts videos uploaded in most container formats, including WMV (Windows Media Video), 3GP (Cell Phones), AVI (Windows), MOV (Mac), MP4 (iPod/PSP), FLV (Adobe Flash), MKV (H.264). These include video codecs such as MP4, MPEG and WMV. iMovie is a common video editing software application comes with every Mac for users to edit their own home movies. It imports video footage to the Mac using either the Firewire interface on most MiniDV format digital video cameras, the USB port, or by importing the files from a hard drive where users can edit the video clips, add titles, and add music. Since 1999, eight versions of iMovie have been released by Apple, each with its own functions and characteristic, and each of them deal with videos in a way more or less different. But the most common formats handled with iMovie if specialty discarded as far as to my research are MOV, DV, HDV, MPEG-4. Three ways for successful upload iMovie files to YouTube Solution one and solution two suitable for those who are 100 certainty with their iMovie files which are fully compatible with YouTube. For smooth uploading, you are required to get a YouTube account first. Solution 1: Directly upload iMovie to YouTube Step 1: Launch iMovie, select the project you want to upload in YouTube. Step 2: Go to the file menu, click Share, select Export Movie Step 3: Specify the output file name and directory and then type the video type and video size. Solution 2: Post iMovie to YouTube straightly Step 1: Launch iMovie, choose the project you want to post in YouTube Step 2: From the Share menu, choose YouTube Step 3: In the pop-up YouTube windows, specify the name of your YouTube account, the password, choose the Category and fill in the description and tags of the project. Tick Make this movie more private on the bottom of the window, if possible, to limit those who can view the project. Click Next, and then click Publish. iMovie will automatically export and upload the movie to YouTube. Step 4: Click Tell a Friend to email friends and your family about your film. You are also allowed to copy the URL from Tell a Friend window and paste it into an email you created in your favourite email application if you like. Anyone you send to email to will be able to follow the URL directly to your movie. Note: Videos uploaded to YouTube are limited to ten minutes in length and a file size of 2GB. Solution 3: Upload to iMovie after conversion If neither of the above mentioned method works, there is still a third way to turn to. Sometimes, your iMovie files may not be recognized by YouTube due to the versions of iMovie (settings and functions may varies among versions), video itself (video format difference because of file extension, resolution, video size and length), compatibility (videos that are completely incompatible with YouTube). In this circumstance, the best and reliable method is to convert your iMovie files to YouTube accepted files, iMovie to YouTube converter will be inevitably the ideal choice. iMovie to YouTube converter is an elaborately designed tool for convert iMovie files to YouTube workable WMV, 3GP, AVI, MOV, MP4, FLV, MKV for smooth uploading with hard-to-believe conversion speed and second to none output quality. It can also convert between almost all popular popular file formats like AVI, WMV, MPG, MOV, VOB, DV, MP4, FLV, 3GP, RM, ASF, SWF, MP3, AAC, AC3, AIFF, AMR, WAV, WMA etc so as to put on various portable devices, import to video editing software or play on vast amount video players. iMovie to YouTube converter can also served as an excellent video editing tool to meet your specific program requirements. For example, you can cut your video files to a certain length, or split your video files to smaller ones and select the proper resolution suitable for demands of YouTube by Clip or Settings separately. Crop allows you to cut off unwanted black edges from your videos. Besides, you can also have a good command of the whole process or snapshot your favourite pictures from the preview window. More can be expected if you have a try.

  Read the article

• SonicOS Enhanced 5.8.1.2 L2TP VPN Authentication Failed

  - by Dean A. Vassallo

  I have a SonicWall TZ 215 running SonicOS Enhanced 5.8.1.2-6o. I have configured the L2TP VPN using the default crypto suite ESP: 3DES/HMAC SHA1 (IKE). Proposals are as such: IKE (Phase 1) Proposal DH Group: Group 2 Encryption: 3DES Authentication: SHA1 Life Time (seconds): 28800 Ipsec (Phase 2) Proposal Protocol: ESP Encryption: 3DES Authentication: SHA1 Enable Perfect Forward Secrecy DISABLED Life Time (seconds): 28800 When attempting to connect via my Mac OS X client I get an authentication error. It appears to pass the pre-authentication but fails to complete. I am at a complete loss. I reconfigured from scratch multiple times...used simple usernames and passwords to verify this wasn't a miskeyed password issue. I have Here are the logs (noted IP has been removed for privacy): 7/1/13 8:19:05.174 PM pppd[1268]: setup_security_context server port: 0x1503 7/1/13 8:19:05.190 PM pppd[1268]: publish_entry SCDSet() failed: Success! 7/1/13 8:19:05.191 PM pppd[1268]: publish_entry SCDSet() failed: Success! 7/1/13 8:19:05.191 PM pppd[1268]: pppd 2.4.2 (Apple version 727.1.1) started by dean, uid 501 7/1/13 8:19:05.192 PM pppd[1268]: L2TP connecting to server ‘0.0.0.0’ (0.0.0.0)... 7/1/13 8:19:05.193 PM pppd[1268]: IPSec connection started 7/1/13 8:19:05.208 PM racoon[1269]: accepted connection on vpn control socket. 7/1/13 8:19:05.209 PM racoon[1269]: Connecting. 7/1/13 8:19:05.209 PM racoon[1269]: IPSec Phase 1 started (Initiated by me). 7/1/13 8:19:05.209 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). 7/1/13 8:19:05.209 PM racoon[1269]: >>>>> phase change status = Phase 1 started by us 7/1/13 8:19:05.231 PM racoon[1269]: >>>>> phase change status = Phase 1 started by peer 7/1/13 8:19:05.231 PM racoon[1269]: IKE Packet: receive success. (Initiator, Main-Mode message 2). 7/1/13 8:19:05.234 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Main-Mode message 3). 7/1/13 8:19:05.293 PM racoon[1269]: IKE Packet: receive success. (Initiator, Main-Mode message 4). 7/1/13 8:19:05.295 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Main-Mode message 5). 7/1/13 8:19:05.315 PM racoon[1269]: IKEv1 Phase 1 AUTH: success. (Initiator, Main-Mode Message 6). 7/1/13 8:19:05.315 PM racoon[1269]: IKE Packet: receive success. (Initiator, Main-Mode message 6). 7/1/13 8:19:05.315 PM racoon[1269]: IKEv1 Phase 1 Initiator: success. (Initiator, Main-Mode). 7/1/13 8:19:05.315 PM racoon[1269]: IPSec Phase 1 established (Initiated by me). 7/1/13 8:19:06.307 PM racoon[1269]: IPSec Phase 2 started (Initiated by me). 7/1/13 8:19:06.307 PM racoon[1269]: >>>>> phase change status = Phase 2 started 7/1/13 8:19:06.308 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). 7/1/13 8:19:06.332 PM racoon[1269]: attribute has been modified. 7/1/13 8:19:06.332 PM racoon[1269]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). 7/1/13 8:19:06.332 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). 7/1/13 8:19:06.333 PM racoon[1269]: IKEv1 Phase 2 Initiator: success. (Initiator, Quick-Mode). 7/1/13 8:19:06.333 PM racoon[1269]: IPSec Phase 2 established (Initiated by me). 7/1/13 8:19:06.333 PM racoon[1269]: >>>>> phase change status = Phase 2 established 7/1/13 8:19:06.333 PM pppd[1268]: IPSec connection established 7/1/13 8:19:07.145 PM pppd[1268]: L2TP connection established. 7/1/13 8:19:07.000 PM kernel[0]: ppp0: is now delegating en0 (type 0x6, family 2, sub-family 3) 7/1/13 8:19:07.146 PM pppd[1268]: Connect: ppp0 <--> socket[34:18] 7/1/13 8:19:08.709 PM pppd[1268]: MS-CHAPv2 mutual authentication failed. 7/1/13 8:19:08.710 PM pppd[1268]: Connection terminated. 7/1/13 8:19:08.710 PM pppd[1268]: L2TP disconnecting... 7/1/13 8:19:08.711 PM pppd[1268]: L2TP disconnected 7/1/13 8:19:08.711 PM racoon[1269]: IPSec disconnecting from server 0.0.0.0 7/1/13 8:19:08.711 PM racoon[1269]: IKE Packet: transmit success. (Information message). 7/1/13 8:19:08.712 PM racoon[1269]: IKEv1 Information-Notice: transmit success. (Delete IPSEC-SA). 7/1/13 8:19:08.712 PM racoon[1269]: IKE Packet: transmit success. (Information message). 7/1/13 8:19:08.712 PM racoon[1269]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). 7/1/13 8:19:08.713 PM racoon[1269]: glob found no matches for path "/var/run/racoon/*.conf" 7/1/13 8:19:08.714 PM racoon[1269]: pfkey DELETE failed: No such file or directory

  Read the article

• LDAP query on linux against AD returns groups with no members

  - by SethG

  I am using LDAP+kerberos to authenticate against Active Directory on Windows 2003 R2. My krb5.conf and ldap.conf appear to be correct (according to pretty much every sample I found on the 'net). I can login to the host with both password and ssh keys. When I run getent passwd, all my ldap user accounts are listed with all the important attributes. When I run getent group, all the ldap groups and their gid's are listed, but no group members. If I run ldapsearch and filter on any group, the members are all listed with the "member" attribute. So the data is there for the taking, it's just not being parsed properly. It would appear that I simply am using an incorrect mapping in ldap.conf, but I can't see it. I've tried several variations and all give the same result. Here is my current ldap.conf: host <ad-host1-ip> <ad-host2-ip> base dc=my,dc=full,dc=dn uri ldap://<ad-host1> ldap://<ad-host2> ldap_version 3 binddn <mybinddn> bindpw <mybindpw> scope sub bind_policy hard nss_reconnect_tries 3 nss_reconnect_sleeptime 1 nss_reconnect_maxsleeptime 8 nss_reconnect_maxconntries 3 nss_map_objectclass posixAccount User nss_map_objectclass posixGroup Group nss_map_attribute uid sAMAccountName nss_map_attribute gidNumber msSFU30GidNumber nss_map_attribute uidNumber msSFU30UidNumber nss_map_attribute cn cn nss_map_attribute gecos displayName nss_map_attribute homeDirectory msSFU30HomeDirectory nss_map_attribute loginShell msSFU30LoginShell nss_map_attribute uniqueMember member pam_filter objectcategory=User pam_login_attribute sAMAccountName pam_member_attribute member pam_password ad Here's the kicker: this config works 100% fine on a different linux box with a different distro. It does not work on the distro I am planning on switching to. I have installed from source the versions of pam_ldap and nss_ldap on the new box to match the old box, which fixed another problem I was having with this setup. Other relevant info is the original AD box was Windows 2003. It's mirror died a horrible hardware death so I'm trying to add two more 2003-R2 servers to the mirror tree and ultimately drop the old 2003 box. The new R2 boxes appear to have joined the DC forest properly. What do I need to do to get groups working? I've exhausted all the resources I could find and need a different angle. Any input is appreciated. Status update, 7/31/09 I have managed to tweak my config file to get full info from the AD and performance is nice and snappy. I replaced the back-rev'd copies of pam_ldap and nss_ldap with the current ones for the distro I'm using, so it's back to a standard out-of-the-box install. Here's my current config: host <ad-host1-ip> <ad-host2-ip> base dc=my,dc=full,dc=dn uri ldap://<ad-host1> ldap://<ad-host2> ldap_version 3 binddn <mybinddn> bindpw <mybindpw> scope sub bind_policy soft nss_reconnect_tries 3 nss_reconnect_sleeptime 1 nss_reconnect_maxsleeptime 8 nss_reconnect_maxconntries 3 nss_connect_policy oneshot referrals no nss_map_objectclass posixAccount User nss_map_objectclass posixGroup Group nss_map_attribute uid sAMAccountName nss_map_attribute gidNumber msSFU30GidNumber nss_map_attribute uidNumber msSFU30UidNumber nss_map_attribute cn cn nss_map_attribute gecos displayName nss_map_attribute homeDirectory msSFU30HomeDirectory nss_map_attribute loginShell msSFU30LoginShell nss_map_attribute uniqueMember member pam_filter objectcategory=CN=Person,CN=Schema,CN=Configuration,DC=w2k,DC=cis,DC=ksu,DC=edu pam_login_attribute sAMAccountName pam_member_attribute member pam_password ad ssl off tls_checkpeer no sasl_secprops maxssf=0 The remaining problem now is when you run the groups command, not all subscribed groups are listed. Some are (one or two), but not all. Group memberships are still honored, such as file and printer access. getent group foo still shows that the user is a member of group foo. So it appears to be a presentation bug, and does not interfere with normal operation. It also appears that some (I have not determined exactly how many) group searches do not resolve correctly, even though the group is listed. eg, when you run "getent group bar", nothing is returned, but if you run "getent group|grep bar" or "getent group|grep <bar_gid>" you can see that it indeed listed and your group name and gid are correct. This still seems like an LDAP search or mapping error, but I can't figure out what it is. I'm a heckuva lot closer than earlier in the week, but I'd really like to get this last detail ironed out.

  Read the article

• Create user in Oracle 11g with same priviledges as in Oracle 10g XE

  - by Álvaro G. Vicario

  I'm a PHP developer (not a DBA) and I've been working with Oracle 10g XE for a while. I'm used to XE's simplified user management: Go to Administration/ Users/ Create user Assign user name and password Roles: leave the default ones (connect and resource) Privileges: click on "Enable all" to select the 11 possible ones Create This way I get a user that has full access to its data and no access to everything else. This is fine since I only need it to develop my app. When the app is to be deployed, the client's DBAs configure the environment. Now I have to create users in a full Oracle 11g server and I'm completely lost. I have a new concept (profiles) and there're like 20 roles and hundreds of privileges in various categories. What steps do I need to complete in Oracle Enterprise Manager in order to obtain a user with the same privileges I used to assign in XE? ==== UPDATE ==== I think I'd better provide a detailed explanation so I make myself clearer. This is how I create a user in 10g XE: Roles: [X] CONNECT [X] RESOURCE [ ] DBA Direct Asignment System Privileges: [ ] CREATE DATABASE LINK [ ] CREATE MATERIALIZED VIEW [ ] CREATE PROCEDURE [ ] CREATE PUBLIC SYNONYM [ ] CREATE ROLE [ ] CREATE SEQUENCE [ ] CREATE SYNONYM [ ] CREATE TABLE [ ] CREATE TRIGGER [ ] CREATE TYPE [ ] CREATE VIEW I click on Enable All and I'm done. This is what I'm asked when doing the same in 11g: Profile: (*) DEFAULT ( ) WKSYS_PROF ( ) MONITORING_PROFILE Roles: CONNECT: [ ] Admin option [X] Default value Edit List: AQ_ADMINISTRATOR_ROLE AQ_USER_ROLE AUTHENTICATEDUSER CSW_USR_ROLE CTXAPP CWM_USER DATAPUMP_EXP_FULL_DATABASE DATAPUMP_IMP_FULL_DATABASE DBA DELETE_CATALOG_ROLE EJBCLIENT EXECUTE_CATALOG_ROLE EXP_FULL_DATABASE GATHER_SYSTEM_STATISTICS GLOBAL_AQ_USER_ROLE HS_ADMIN_ROLE IMP_FULL_DATABASE JAVADEBUGPRIV JAVAIDPRIV JAVASYSPRIV JAVAUSERPRIV JAVA_ADMIN JAVA_DEPLOY JMXSERVER LOGSTDBY_ADMINISTRATOR MGMT_USER OEM_ADVISOR OEM_MONITOR OLAPI_TRACE_USER OLAP_DBA OLAP_USER OLAP_XS_ADMIN ORDADMIN OWB$CLIENT OWB_DESIGNCENTER_VIEW OWB_USER RECOVERY_CATALOG_OWNER RESOURCE SCHEDULER_ADMIN SELECT_CATALOG_ROLE SPATIAL_CSW_ADMIN SPATIAL_WFS_ADMIN WFS_USR_ROLE WKUSER WM_ADMIN_ROLE XDBADMIN XDB_SET_INVOKER XDB_WEBSERVICES XDB_WEBSERVICES_OVER_HTTP XDB_WEBSERVICES_WITH_PUBLIC System Privileges: <Empty> Edit List: ACCESS_ANY_WORKSPACE ADMINISTER ANY SQL TUNING SET ADMINISTER DATABASE TRIGGER ADMINISTER RESOURCE MANAGER ADMINISTER SQL MANAGEMENT OBJECT ADMINISTER SQL TUNING SET ADVISOR ALTER ANY ASSEMBLY ALTER ANY CLUSTER ALTER ANY CUBE ALTER ANY CUBE DIMENSION ALTER ANY DIMENSION ALTER ANY EDITION ALTER ANY EVALUATION CONTEXT ALTER ANY INDEX ALTER ANY INDEXTYPE ALTER ANY LIBRARY ALTER ANY MATERIALIZED VIEW ALTER ANY MINING MODEL ALTER ANY OPERATOR ALTER ANY OUTLINE ALTER ANY PROCEDURE ALTER ANY ROLE ALTER ANY RULE ALTER ANY RULE SET ALTER ANY SEQUENCE ALTER ANY SQL PROFILE ALTER ANY TABLE ALTER ANY TRIGGER ALTER ANY TYPE ALTER DATABASE ALTER PROFILE ALTER RESOURCE COST ALTER ROLLBACK SEGMENT ALTER SESSION ALTER SYSTEM ALTER TABLESPACE ALTER USER ANALYZE ANY ANALYZE ANY DICTIONARY AUDIT ANY AUDIT SYSTEM BACKUP ANY TABLE BECOME USER CHANGE NOTIFICATION COMMENT ANY MINING MODEL COMMENT ANY TABLE CREATE ANY ASSEMBLY CREATE ANY CLUSTER CREATE ANY CONTEXT CREATE ANY CUBE CREATE ANY CUBE BUILD PROCESS CREATE ANY CUBE DIMENSION CREATE ANY DIMENSION CREATE ANY DIRECTORY CREATE ANY EDITION CREATE ANY EVALUATION CONTEXT CREATE ANY INDEX CREATE ANY INDEXTYPE CREATE ANY JOB CREATE ANY LIBRARY CREATE ANY MATERIALIZED VIEW CREATE ANY MEASURE FOLDER CREATE ANY MINING MODEL CREATE ANY OPERATOR CREATE ANY OUTLINE CREATE ANY PROCEDURE CREATE ANY RULE CREATE ANY RULE SET CREATE ANY SEQUENCE CREATE ANY SQL PROFILE CREATE ANY SYNONYM CREATE ANY TABLE CREATE ANY TRIGGER CREATE ANY TYPE CREATE ANY VIEW CREATE ASSEMBLY CREATE CLUSTER CREATE CUBE CREATE CUBE BUILD PROCESS CREATE CUBE DIMENSION CREATE DATABASE LINK CREATE DIMENSION CREATE EVALUATION CONTEXT CREATE EXTERNAL JOB CREATE INDEXTYPE CREATE JOB CREATE LIBRARY CREATE MATERIALIZED VIEW CREATE MEASURE FOLDER CREATE MINING MODEL CREATE OPERATOR CREATE PROCEDURE CREATE PROFILE CREATE PUBLIC DATABASE LINK CREATE PUBLIC SYNONYM CREATE ROLE CREATE ROLLBACK SEGMENT CREATE RULE CREATE RULE SET CREATE SEQUENCE CREATE SESSION CREATE SYNONYM CREATE TABLE CREATE TABLESPACE CREATE TRIGGER CREATE TYPE CREATE USER CREATE VIEW CREATE_ANY_WORKSPACE DEBUG ANY PROCEDURE DEBUG CONNECT SESSION DELETE ANY CUBE DIMENSION DELETE ANY MEASURE FOLDER DELETE ANY TABLE DEQUEUE ANY QUEUE DROP ANY ASSEMBLY DROP ANY CLUSTER DROP ANY CONTEXT DROP ANY CUBE DROP ANY CUBE BUILD PROCESS DROP ANY CUBE DIMENSION DROP ANY DIMENSION DROP ANY DIRECTORY DROP ANY EDITION DROP ANY EVALUATION CONTEXT DROP ANY INDEX DROP ANY INDEXTYPE DROP ANY LIBRARY DROP ANY MATERIALIZED VIEW DROP ANY MEASURE FOLDER DROP ANY MINING MODEL DROP ANY OPERATOR DROP ANY OUTLINE DROP ANY PROCEDURE DROP ANY ROLE DROP ANY RULE DROP ANY RULE SET DROP ANY SEQUENCE DROP ANY SQL PROFILE DROP ANY SYNONYM DROP ANY TABLE DROP ANY TRIGGER DROP ANY TYPE DROP ANY VIEW DROP PROFILE DROP PUBLIC DATABASE LINK DROP PUBLIC SYNONYM DROP ROLLBACK SEGMENT DROP TABLESPACE DROP USER ENQUEUE ANY QUEUE EXECUTE ANY ASSEMBLY EXECUTE ANY CLASS EXECUTE ANY EVALUATION CONTEXT EXECUTE ANY INDEXTYPE EXECUTE ANY LIBRARY EXECUTE ANY OPERATOR EXECUTE ANY PROCEDURE EXECUTE ANY PROGRAM EXECUTE ANY RULE EXECUTE ANY RULE SET EXECUTE ANY TYPE EXECUTE ASSEMBLY EXPORT FULL DATABASE FLASHBACK ANY TABLE FLASHBACK ARCHIVE ADMINISTER FORCE ANY TRANSACTION FORCE TRANSACTION FREEZE_ANY_WORKSPACE GLOBAL QUERY REWRITE GRANT ANY OBJECT PRIVILEGE GRANT ANY PRIVILEGE GRANT ANY ROLE IMPORT FULL DATABASE INSERT ANY CUBE DIMENSION INSERT ANY MEASURE FOLDER INSERT ANY TABLE LOCK ANY TABLE MANAGE ANY FILE GROUP MANAGE ANY QUEUE MANAGE FILE GROUP MANAGE SCHEDULER MANAGE TABLESPACE MERGE ANY VIEW MERGE_ANY_WORKSPACE ON COMMIT REFRESH QUERY REWRITE READ ANY FILE GROUP REMOVE_ANY_WORKSPACE RESTRICTED SESSION RESUMABLE ROLLBACK_ANY_WORKSPACE SELECT ANY CUBE SELECT ANY CUBE DIMENSION SELECT ANY DICTIONARY SELECT ANY MINING MODEL SELECT ANY SEQUENCE SELECT ANY TABLE SELECT ANY TRANSACTION UNDER ANY TABLE UNDER ANY TYPE UNDER ANY VIEW UNLIMITED TABLESPACE UPDATE ANY CUBE UPDATE ANY CUBE BUILD PROCESS UPDATE ANY CUBE DIMENSION UPDATE ANY TABLE Object Privileges: <Empty> Add: Clase Java Clases de Trabajos Cola Columna de Tabla Columna de Vista Espacio de Trabajo Función Instantánea Origen Java Paquete Planificaciones Procedimiento Programas Secuencia Sinónimo Tabla Tipos Trabajos Vista Consumer Group Privileges: <Empty> Default Consumer Group: (*) None Edit List: AUTO_TASK_CONSUMER_GROUP BATCH_GROUP DEFAULT_CONSUMER_GROUP INTERACTIVE_GROUP LOW_GROUP ORA$AUTOTASK_HEALTH_GROUP ORA$AUTOTASK_MEDIUM_GROUP ORA$AUTOTASK_SPACE_GROUP ORA$AUTOTASK_SQL_GROUP ORA$AUTOTASK_STATS_GROUP ORA$AUTOTASK_URGENT_GROUP ORA$DIAGNOSTICS SYS_GROUP And, of course, I wonder what options I should pick.

  Read the article

• Windows 7 client can't connect to CentOS PPTP VPN

  - by Chris

  Have a Macintosh (10.8.2) that connects just fine to a CentOS 6.0 virtual private server (OpenVZ, with PPP added by the host) via PPTP. A Windows 7 Home Premium client (virtualized in Sun's Virtual Box), on the same computer, using the same Ethernet connection, cannot connect to the Linux VPN server. I have iptables disabled (for testing) on the Linux box. I have the Windows firewall turned off. /var/log/messages looks like this, for a Windows connection: Oct 12 18:44:30 production pptpd[1880]: CTRL: Client 66.104.246.168 control connection started Oct 12 18:44:30 production pptpd[1880]: CTRL: Starting call (launching pppd, opening GRE) Oct 12 18:44:30 production pppd[1881]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Oct 12 18:44:30 production pppd[1881]: pptpd-logwtmp: $Version$ Oct 12 18:44:30 production pppd[1881]: pppd options in effect: Oct 12 18:44:30 production pppd[1881]: debug#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: nologfd#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: dump#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: plugin /usr/lib/pptpd/pptpd-logwtmp.so#011#011# (from command line) Oct 12 18:44:30 production pppd[1881]: require-mschap-v2#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: refuse-pap#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: refuse-chap#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: refuse-mschap#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: name pptpd#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: pptpd-original-ip 66.104.246.168#011#011# (from command line) Oct 12 18:44:30 production pppd[1881]: 115200#011#011# (from command line) Oct 12 18:44:30 production pppd[1881]: lock#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: local#011#011# (from command line) Oct 12 18:44:30 production pppd[1881]: novj#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: novjccomp#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: ipparam 66.104.246.168#011#011# (from command line) Oct 12 18:44:30 production pppd[1881]: proxyarp#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: 192.168.97.1:192.168.97.10#011#011# (from command line) Oct 12 18:44:30 production pppd[1881]: nobsdcomp#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: require-mppe-128#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: mppe-stateful#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: pppd 2.4.5 started by root, uid 0 Oct 12 18:44:30 production pppd[1881]: Using interface ppp0 Oct 12 18:44:30 production pppd[1881]: Connect: ppp0 <--> /dev/pts/1 (At this point the Windows machine displays a dialog, reading: "Verifying user name and password...") Oct 12 18:45:00 production pppd[1881]: LCP: timeout sending Config-Requests Oct 12 18:45:00 production pppd[1881]: Connection terminated. Oct 12 18:45:00 production pppd[1881]: Modem hangup Oct 12 18:45:00 production pppd[1881]: Exit. Oct 12 18:45:00 production pptpd[1880]: GRE: read(fd=6,buffer=8059660,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Oct 12 18:45:00 production pptpd[1880]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Oct 12 18:45:00 production pptpd[1880]: CTRL: Client 66.104.246.168 control connection finished The Macintosh connecting looks like this in /var/log/messages: Oct 12 18:50:49 production pptpd[1920]: CTRL: Client 66.104.246.168 control connection started Oct 12 18:50:49 production pptpd[1920]: CTRL: Starting call (launching pppd, opening GRE) Oct 12 18:50:49 production pppd[1921]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Oct 12 18:50:49 production pppd[1921]: pptpd-logwtmp: $Version$ Oct 12 18:50:49 production pppd[1921]: pppd options in effect: Oct 12 18:50:49 production pppd[1921]: debug#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: nologfd#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: dump#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: plugin /usr/lib/pptpd/pptpd-logwtmp.so#011#011# (from command line) Oct 12 18:50:49 production pppd[1921]: require-mschap-v2#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: refuse-pap#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: refuse-chap#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: refuse-mschap#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: name pptpd#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: pptpd-original-ip 66.104.246.168#011#011# (from command line) Oct 12 18:50:49 production pppd[1921]: 115200#011#011# (from command line) Oct 12 18:50:49 production pppd[1921]: lock#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: local#011#011# (from command line) Oct 12 18:50:49 production pppd[1921]: novj#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: novjccomp#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: ipparam 66.104.246.168#011#011# (from command line) Oct 12 18:50:49 production pppd[1921]: proxyarp#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: 192.168.97.1:192.168.97.10#011#011# (from command line) Oct 12 18:50:49 production pppd[1921]: nobsdcomp#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: require-mppe-128#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: mppe-stateful#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: pppd 2.4.5 started by root, uid 0 Oct 12 18:50:49 production pppd[1921]: Using interface ppp0 Oct 12 18:50:49 production pppd[1921]: Connect: ppp0 <--> /dev/pts/1 Oct 12 18:50:52 production pppd[1921]: MPPE 128-bit stateless compression enabled Oct 12 18:50:52 production pppd[1921]: Unsupported protocol 'IPv6 Control Protocol' (0x8057) received Oct 12 18:50:52 production pppd[1921]: Unsupported protocol 'Apple Client Server Protocol Control' (0x8235) received Oct 12 18:50:52 production pppd[1921]: Cannot determine ethernet address for proxy ARP Oct 12 18:50:52 production pppd[1921]: local IP address 192.168.97.1 Oct 12 18:50:52 production pppd[1921]: remote IP address 192.168.97.10 Oct 12 18:50:52 production pppd[1921]: pptpd-logwtmp.so ip-up ppp0 chris 66.104.246.168 I'm baffled...

  Read the article

• postfix 5.7.1 Relay access denied when sending mail with cron

  - by zensys

  Reluctant to ask because there is so much here about 'postfix relay access denied' but I cannot find my case: I use php (Zend Framework) to send emails outside my network using the Google mail server because I could not send mail outside my server (user: web). However when I sent out an email via cron (user: root, I believe), still using ZF, using the same mail config/credentials, I get the message: '5.7.1 Relay access denied' I guess I need to know one of two things: 1. How can I use the google smtp server from cron 2. What do I need to change in my config to send mail using my own server instead of google Though the answer to 2. is the more structural solution I assume, I am quite happy with an answer to 1. as well because I think Google is better at server maintaince (security/spam) than I am. Below my ZF application.ini mail section, main.cf and master.cf: application.ini: resources.mail.transport.type = smtp resources.mail.transport.auth = login resources.mail.transport.host = "smtp.gmail.com" resources.mail.transport.ssl = tls resources.mail.transport.port = 587 resources.mail.transport.username = [email protected] resources.mail.transport.password = xxxxxxx resources.mail.defaultFrom.email = [email protected] resources.mail.defaultFrom.name = "my company" main.cf: # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = /usr/share/doc/postfix # TLS parameters smtpd_tls_cert_file = /etc/postfix/smtpd.cert smtpd_tls_key_file = /etc/postfix/smtpd.key smtpd_use_tls = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = mail.second-start.nl mydomain = second-start.nl alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all html_directory = /usr/share/doc/postfix/html message_size_limit = 30720000 virtual_alias_domains = virtual_alias_maps = proxy:mysql:/etc/postfix/mysql-virtual_forwardings.cf, mysql:/etc/postfix/mysql-virtual_email2email.cf virtual_mailbox_domains = proxy:mysql:/etc/postfix/mysql-virtual_domains.cf virtual_mailbox_maps = proxy:mysql:/etc/postfix/mysql-virtual_mailboxes.cf virtual_mailbox_base = /home/vmail virtual_uid_maps = static:5000 virtual_gid_maps = static:5000 smtpd_sasl_auth_enable = yes broken_sasl_auth_clients = yes smtpd_sasl_authenticated_header = yes # see under Spam smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination proxy_read_maps = $local_recipient_maps $mydestination $virtual_alias_maps $virtual_alias_domains $virtual_mailbox_maps $virtual_mailbox_domains $relay_recipient_maps $relay_domains $canonical_maps $sender_canonical_maps $recipient_canonical_maps $relocated_maps $transport_maps $mynetworks $virtual_mailbox_limit_maps virtual_transport = dovecot dovecot_destination_recipient_limit = 1 # Spam disable_vrfy_command = yes smtpd_delay_reject = yes smtpd_helo_required = yes smtpd_helo_restrictions = permit_mynetworks, check_helo_access hash:/etc/postfix/helo_access, reject_non_fqdn_hostname, reject_invalid_hostname, permit smtpd_recipient_restrictions = permit_sasl_authenticated, reject_unauth_destination, reject_invalid_hostname, reject_non_fqdn_sender, reject_non_fqdn_recipient, reject_unknown_sender_domain, reject_unknown_recipient_domain, permit_mynetworks, reject_non_fqdn_hostname, reject_rbl_client sbl.spamhaus.org, reject_rbl_client zen.spamhaus.org, reject_rbl_client cbl.abuseat.org, reject_rbl_client bl.spamcop.net, permit smtpd_error_sleep_time = 1s smtpd_soft_error_limit = 10 smtpd_hard_error_limit = 20 master.cf: # ========================================================================== # service type private unpriv chroot wakeup maxproc command + args # (yes) (yes) (yes) (never) (100) # ========================================================================== smtp inet n - - - - smtpd #smtp inet n - - - 1 postscreen #smtpd pass - - - - - smtpd #dnsblog unix - - - - 0 dnsblog #tlsproxy unix - - - - 0 tlsproxy #submission inet n - - - - smtpd # -o smtpd_tls_security_level=encrypt # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING #smtps inet n - - - - smtpd # -o smtpd_tls_wrappermode=yes # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING #628 inet n - - - - qmqpd pickup fifo n - - 60 1 pickup cleanup unix n - - - 0 cleanup qmgr fifo n - n 300 1 qmgr #qmgr fifo n - - 300 1 oqmgr tlsmgr unix - - - 1000? 1 tlsmgr rewrite unix - - - - - trivial-rewrite bounce unix - - - - 0 bounce defer unix - - - - 0 bounce trace unix - - - - 0 bounce verify unix - - - - 1 verify flush unix n - - 1000? 0 flush proxymap unix - - n - - proxymap proxywrite unix - - n - 1 proxymap smtp unix - - - - - smtp # When relaying mail as backup MX, disable fallback_relay to avoid MX loops relay unix - - - - - smtp -o smtp_fallback_relay= # -o smtp_helo_timeout=5 -o smtp_connect_timeout=5 showq unix n - - - - showq error unix - - - - - error retry unix - - - - - error discard unix - - - - - discard local unix - n n - - local virtual unix - n n - - virtual lmtp unix - - - - - lmtp anvil unix - - - - 1 anvil scache unix - - - - 1 scache # # ==================================================================== # Interfaces to non-Postfix software. Be sure to examine the manual # pages of the non-Postfix software to find out what options it wants. # # Many of the following services use the Postfix pipe(8) delivery # agent. See the pipe(8) man page for information about ${recipient} # and other message envelope options. # ==================================================================== # # maildrop. See the Postfix MAILDROP_README file for details. # Also specify in main.cf: maildrop_destination_recipient_limit=1 # maildrop unix - n n - - pipe flags=DRhu user=vmail argv=/usr/bin/maildrop -d ${recipient} # # ==================================================================== # # Recent Cyrus versions can use the existing "lmtp" master.cf entry. # # Specify in cyrus.conf: # lmtp cmd="lmtpd -a" listen="localhost:lmtp" proto=tcp4 # # Specify in main.cf one or more of the following: # mailbox_transport = lmtp:inet:localhost # virtual_transport = lmtp:inet:localhost # # ==================================================================== # # Cyrus 2.1.5 (Amos Gouaux) # Also specify in main.cf: cyrus_destination_recipient_limit=1 # #cyrus unix - n n - - pipe # user=cyrus argv=/cyrus/bin/deliver -e -r ${sender} -m ${extension} ${user} # # ==================================================================== # Old example of delivery via Cyrus. # #old-cyrus unix - n n - - pipe # flags=R user=cyrus argv=/cyrus/bin/deliver -e -m ${extension} ${user} # # ==================================================================== # # See the Postfix UUCP_README file for configuration details. # uucp unix - n n - - pipe flags=Fqhu user=uucp argv=uux -r -n -z -a$sender - $nexthop!rmail ($recipient) # # Other external delivery methods. # ifmail unix - n n - - pipe flags=F user=ftn argv=/usr/lib/ifmail/ifmail -r $nexthop ($recipient) bsmtp unix - n n - - pipe flags=Fq. user=bsmtp argv=/usr/lib/bsmtp/bsmtp -t$nexthop -f$sender $recipient scalemail-backend unix - n n - 2 pipe flags=R user=scalemail argv=/usr/lib/scalemail/bin/scalemail-store ${nexthop} ${user} ${extension} mailman unix - n n - - pipe flags=FR user=list argv=/usr/lib/mailman/bin/postfix-to-mailman.py ${nexthop} ${user} dovecot unix - n n - - pipe flags=DRhu user=vmail:vmail argv=/usr/lib/dovecot/deliver -d ${recipient}

  Read the article

• Getting HAPROXY to redirect http to https in users browser session

  - by Jon

  We are currently using a Internet cloud provider to host our SaaS platform. The platform consists of a Firewall - Cloud Provider SLB - - Apache Web Server - HAPROXY SLB - Liferay Platform We have had to use HAPROXY because of an issue with the cloud providers SLB that meant we were unable to use it for load balancing the Liferay platform applications. I have implemented HAPROXY in our secure tier and that seems to do the trick of load balancing the requests quite adequately. However during testing we encountered a functional issue whereby selecting a sub-menu from the web portal resulted in the application hanging, using an http analyser we saw that the request being passed back to the users browser was in http, from discussing this with the software vendor it transpires that the Liferay application has some hard-coded http links, and that other customers have worked around this by using physical NLB's such as F5 and redirecting the http traffic to https. The entry in the HAPROXY logs reads: haproxy[2717]: haproxy[2717]: <Apache Web Agent>:37957 [11/Apr/2013:08:07:00.128] http-uapi uapi/<ServerName> 0/0/0/9/10 200 4912 - - ---- 4/2/1/2/0 0/0 "GET /servicedesk/controller?docommand=renderradform&!key=esd_sfb001_frm_feedback_forms_list&isportalintegratedmode=true&USR=joe.bloggs%40gmail.com&_dc=1365667773097&redirecturl=controller%3Fdocommand%3Drenderbody%26%21key%3DESD_SFB001_FRM_FEEDBACK_FORMS_LIST%26isportalintegratedmode%3Dtrue&sso_token=ALiYv2UqzLsAhSw1ZchRDlCHlq44Bhj9&ONERROR=%2Fweb%2Fjsp%2Fapps%2Fportal-integration-error.jsp&itype=login&slicetoken=NW51O%242aRo%2C_Zz%2476P_9DTtnFmz6%28bhk&AUTOFORWARDURL=controller%3Fdocommand%3Drenderbody%26%21key%3DESD_SFB001_FRM_FEEDBACK_FORMS_LIST%26isportalintegratedmode%3Dtrue&LOGINPAGE=https%3A%2F%2F<FQDN of Web Portal>%2Fweb%2F4732cf01-82c3-4bc5-b6c9-552253e672cf%2Fworkflow-tools&appid=1&!uid=1&!redownloadToken=7.0.3.1.1363611301.0&userlocale=en_US&!datechanged=2012-05-18%2015:05:31.38 HTTP/1.1" :37957 [11/Apr/2013:08:07:00.128] http-uapi uapi/<ServerName> 0/0/0/9/10 200 4912 - - ---- 4/2/1/2/0 0/0 "GET /servicedesk/controller?docommand=renderradform&!key=esd_sfb001_frm_feedback_forms_list&isportalintegratedmode=true&USR=joe.bloggs%40gmail.com&_dc=1365667773097&redirecturl=controller%3Fdocommand%3Drenderbody%26%21key%3DESD_SFB001_FRM_FEEDBACK_FORMS_LIST%26isportalintegratedmode%3Dtrue&sso_token=ALiYv2UqzLsAhSw1ZchRDlCHlq44Bhj9&ONERROR=%2Fweb%2Fjsp%2Fapps%2Fportal-integration-error.jsp&itype=login&slicetoken=NW51O%242aRo%2C_Zz%2476P_9DTtnFmz6%28bhk&AUTOFORWARDURL=controller%3Fdocommand%3Drenderbody%26%21key%3DESD_SFB001_FRM_FEEDBACK_FORMS_LIST%26isportalintegratedmode%3Dtrue&LOGINPAGE=https%3A%2F%2F<FQDN of Web Portal>%2Fweb%2F4732cf01-82c3-4bc5-b6c9-552253e672cf%2Fworkflow-tools&appid=1&!uid=1&!redownloadToken=7.0.3.1.1363611301.0&userlocale=en_US&!datechanged=2012-05-18%2015:05:31.38 HTTP/1.1" The corresponding HTTP browser entry shows: http://<FQDN of ServiceDesk>/servicedesk/controller?docommand=renderradform&!key=esd_org019_frm_contact_list&isportalintegratedmode=true&USR=joe.bloggs%40gmail.com&_dc=1365665987887&redirecturl=controller%3Fdocommand%3Drenderbody%26%21key%3DESD_ORG019_FRM_CONTACT_LIST%26isportalintegratedmode%3Dtrue&sso_token=3NxsXYORMPp32SwL8ftVUCMH2QdWLH82&ONERROR=%2Fweb%2Fjsp%2Fapps%2Fportal-integration-error.jsp&itype=login&slicetoken=NW51O%242aRo%2C_Zz%2476P_9DTtnFmz6%28bhk&AUTOFORWARDURL=controller%3Fdocommand%3Drenderbody%26%21key%3DESD_ORG019_FRM_CONTACT_LIST%26isportalintegratedmode%3Dtrue&LOGINPAGE=https%3A%2F%2F<FQDN of Web Portal>>%2Fweb%2F4732cf01-82c3-4bc5-b6c9-552253e672cf%2Fapplication-setup&appid=1&!uid=1&!redownloadToken=7.0.3.1.1363611301.0&userlocale=en_US&!datechanged=2012-10-26%2019:00:25.08 From reading through the forums and other sites it looks like we should be use to use HAPROXY to redirect the traffic to https, but try as I might I cant get it to work. This is our HAPROXY configuration: global log 127.0.0.1 local2 chroot /var/lib/haproxy pidfile /var/run/haproxy.pid maxconn 4000 user haproxy group haproxy daemon stats socket /var/lib/haproxy/stats defaults mode http log global option httplog option dontlognull option http-server-close option forwardfor except 127.0.0.0/8 option redispatch retries 3 timeout http-request 10s timeout queue 1m timeout connect 10s timeout client 1m timeout server 1m timeout http-keep-alive 10s timeout check 10s maxconn 3000 frontend http-openfire bind *:7070 default_backend openfire backend openfire balance roundrobin server <serverName> <IPv4 Address>:7070 check server <serverName> <IPv4 Address>:7070 check frontend http-uapi bind *:7080 default_backend uapi backend uapi balance roundrobin server <serverName> <IPv4 Address>:7080 check server <serverName> <IPv4 Address>:7080 check frontend http-sec bind *:8080 default_backend sec backend sec balance roundrobin server <serverName> <IPv4 Address>:8080 check server <serverName> <IPv4 Address>:8080 check frontend http-wall bind *:9080 default_backend wall backend wall balance roundrobin server <serverName> <IPv4 Address>:9080 check server <serverName> <IPv4 Address>:9080 check frontend http-xmpp bind *:9090 default_backend xmpp backend xmpp balance roundrobin server <serverName> <IPv4 Address>:9090 check server <serverName> <IPv4 Address>:9090 check frontend http-aim bind *:10080 default_backend aim backend aim balance roundrobin server <serverName> <IPv4 Address>:10080 check server <serverName> <IPv4 Address>:10080 check frontend http-servicedesk bind *:8081 default_backend servicedesk backend servicedesk balance roundrobin server <serverName> <IPv4 Address>:8081 check server <serverName> <IPv4 Address>:8081 check listen stats :1936 mode http stats enable stats hide-version stats realm Haproxy\ Statistics stats uri / stats auth haproxy:<Password> I have tried following the articles listed posted on http://stackoverflow.com/questions/13227544/haproxy-redirecting-http-to-https-ssl and http://parsnips.net/haproxy-http-to-https-redirect/ but that hasn't made any difference. Am I on the right track with this or are we trying to achieve the impossible?, I'm hoping I'm just being an idiot and one of you good people can point me in the right direction.

  Read the article

• Varnish default.vcl grace period

  - by Vladimir

  These are my settings for a grace period (/etc/varnish/default.vcl) sub vcl_recv { .... set req.grace = 360000s; ... } sub vcl_fetch { ... set beresp.grace = 360000s; ... } I tested Varnish using localhost and nodejs as a server. I started localhost, the site was up. Then I disconnected server and the site got disconnected in less than 2 min. It says: Error 503 Service Unavailable Service Unavailable Guru Meditation: XID: 1890127100 Varnish cache server Could you tell me what could be the problem? sub vcl_fetch { if (beresp.ttl < 120s) { ##std.log("Adjusting TTL"); set beresp.ttl = 36000s; ##120s; } # Do not cache the object if the backend application does not want us to. if (beresp.http.Cache-Control ~ "(no-cache|no-store|private|must-revalidate)") { return(hit_for_pass); } # Do not cache the object if the status is not in the 200s if (beresp.status >= 300) { # Remove the Set-Cookie header #remove beresp.http.Set-Cookie; return(hit_for_pass); } # # Everything below here should be cached # # Remove the Set-Cookie header ####remove beresp.http.Set-Cookie; # Set the grace time ## set beresp.grace = 1s; //change this to minutes in case of app shutdown set beresp.grace = 360000s; ## 10 hour - reduce if it has negative impact # Static assets - browser caches tpiphem for a long time. if (req.url ~ "\.(css|js|.js|jpg|jpeg|gif|ico|png)\??\d*$") { /* Remove Expires from backend, it's not long enough */ unset beresp.http.expires; /* Set the clients TTL on this object */ set beresp.http.cache-control = "public, max-age=31536000"; /* marker for vcl_deliver to reset Age: */ set beresp.http.magicmarker = "1"; } else { set beresp.http.Cache-Control = "private, max-age=0, must-revalidate"; set beresp.http.Pragma = "no-cache"; } if (req.url ~ "\.(css|js|min|)\??\d*$") { set beresp.do_gzip = true; unset beresp.http.expires; set beresp.http.cache-control = "public, max-age=31536000"; set beresp.http.expires = beresp.ttl; set beresp.http.age = "0"; } ##do not duplicate these settings if (req.url ~ ".css") { set beresp.do_gzip = true; unset beresp.http.expires; set beresp.http.cache-control = "public, max-age=31536000"; set beresp.http.expires = beresp.ttl; set beresp.http.age = "0"; } if (req.url ~ ".js") { set beresp.do_gzip = true; unset beresp.http.expires; set beresp.http.cache-control = "public, max-age=31536000"; set beresp.http.expires = beresp.ttl; set beresp.http.age = "0"; } if (req.url ~ ".min") { set beresp.do_gzip = true; unset beresp.http.expires; set beresp.http.cache-control = "public, max-age=31536000"; set beresp.http.expires = beresp.ttl; set beresp.http.age = "0"; } ## If the request to the backend returns a code other than 200, restart the loop ## If the number of restarts reaches the value of the parameter max_restarts, ## the request will be error'ed. max_restarts defaults to 4. This prevents ## an eternal loop in the event that, e.g., the object does not exist at all. if (beresp.status != 200 && beresp.status != 403 && beresp.status != 404) { return(restart); } if (beresp.status == 302) { return(deliver); } # Never cache posts if (req.url ~ "\/post\/" || req.url ~ "\/submit\/" || req.url ~ "\/ask\/" || req.url ~ "\/add\/") { return(hit_for_pass); } ##check this setting to ensure that it does not cause issues for browsers with no gzip if (beresp.http.content-type ~ "text") { set beresp.do_gzip = true; } if (beresp.http.Set-Cookie) { return(deliver); } ##if (req.url == "/index.html") { set beresp.do_esi = true; ##} ## check if this is needed or should be used # return(deliver); the object return(deliver); } sub vcl_recv { ##avoid leeching of images call hot_link; set req.grace = 360000s; ##2m ## if one backend is down - use another if (req.restarts == 0) { set req.backend = cache_director; ##we can specify individual VMs } else if (req.restarts == 1) { set req.backend = cache_director; } ## post calls should not be cached - add cookie for these requests if using micro-caching # Pass requests that are not GET or HEAD if (req.request != "GET" && req.request != "HEAD") { return(pass); ## return(pass) goes to backend - not cache } # Don't cache the result of a redirect if (req.http.Referer ~ "redir" || req.http.Origin ~ "jumpto") { return(pass); } # Don't cache the result of a redirect (asking for logon) if (req.http.Referer ~ "post" || req.http.Referer ~ "submit" || req.http.Referer ~ "add" || req.http.Referer ~ "ask") { return(pass); } # Never cache posts - ensure that we do not use these strings in our URLs' that need to be cached if (req.url ~ "\/post\/" || req.url ~ "\/submit\/" || req.url ~ "\/ask\/" || req.url ~ "\/add\/") { return(pass); } ## if (req.http.Authorization || req.http.Cookie) { if (req.http.Authorization) { /* Not cacheable by default */ return (pass); } # Handle compression correctly. Different browsers send different # "Accept-Encoding" headers, even though they mostly all support the same # compression mechanisms. By consolidating these compression headers into # a consistent format, we can reduce the size of the cache and get more hits. # @see: http:// varnish.projects.linpro.no/wiki/FAQ/Compression if (req.http.Accept-Encoding) { if (req.url ~ "\.(jpg|png|gif|gz|tgz|bz2|tbz|mp3|ogg|ico)$") { # No point in compressing these remove req.http.Accept-Encoding; } else if (req.http.Accept-Encoding ~ "gzip") { # If the browser supports it, we'll use gzip. set req.http.Accept-Encoding = "gzip"; } else if (req.http.Accept-Encoding ~ "deflate") { # Next, try deflate if it is supported. set req.http.Accept-Encoding = "deflate"; } else { # Unknown algorithm. Remove it and send unencoded. unset req.http.Accept-Encoding; } } # lookup graphics, css, js & ico files in the cache if (req.url ~ "\.(png|gif|jpg|jpeg|css|.js|ico)$") { return(lookup); } ##added on 0918 - check if it causes issues with user specific content if (req.request == "GET" && req.http.cookie) { return(lookup); } # Pipe requests that are non-RFC2616 or CONNECT which is weird. if (req.request != "GET" && req.request != "HEAD" && req.request != "PUT" && req.request != "POST" && req.request != "TRACE" && req.request != "OPTIONS" && req.request != "DELETE") { ##closing connection and calling pipe return(pipe); } ##purge content via localhost only if (req.request == "PURGE") { if (!client.ip ~ purge) { error 405 "Not allowed."; } return(lookup); } ## do we need this? ## return(lookup); }

  Read the article

• Cisco ASA - Enable communication between same security level

  - by Conor

  I have recently inherited a network with a Cisco ASA (running version 8.2). I am trying to configure it to allow communication between two interfaces configured with the same security level (DMZ-DMZ) "same-security-traffic permit inter-interface" has been set, but hosts are unable to communicate between the interfaces. I am assuming that some NAT settings are causing my issue. Below is my running config: ASA Version 8.2(3) ! hostname asa enable password XXXXXXXX encrypted passwd XXXXXXXX encrypted names ! interface Ethernet0/0 switchport access vlan 400 ! interface Ethernet0/1 switchport access vlan 400 ! interface Ethernet0/2 switchport access vlan 420 ! interface Ethernet0/3 switchport access vlan 420 ! interface Ethernet0/4 switchport access vlan 450 ! interface Ethernet0/5 switchport access vlan 450 ! interface Ethernet0/6 switchport access vlan 500 ! interface Ethernet0/7 switchport access vlan 500 ! interface Vlan400 nameif outside security-level 0 ip address XX.XX.XX.10 255.255.255.248 ! interface Vlan420 nameif public security-level 20 ip address 192.168.20.1 255.255.255.0 ! interface Vlan450 nameif dmz security-level 50 ip address 192.168.10.1 255.255.255.0 ! interface Vlan500 nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0 ! ftp mode passive clock timezone JST 9 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network DM_INLINE_NETWORK_1 network-object host XX.XX.XX.11 network-object host XX.XX.XX.13 object-group service ssh_2220 tcp port-object eq 2220 object-group service ssh_2251 tcp port-object eq 2251 object-group service ssh_2229 tcp port-object eq 2229 object-group service ssh_2210 tcp port-object eq 2210 object-group service DM_INLINE_TCP_1 tcp group-object ssh_2210 group-object ssh_2220 object-group service zabbix tcp port-object range 10050 10051 object-group service DM_INLINE_TCP_2 tcp port-object eq www group-object zabbix object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service http_8029 tcp port-object eq 8029 object-group network DM_INLINE_NETWORK_2 network-object host 192.168.20.10 network-object host 192.168.20.30 network-object host 192.168.20.60 object-group service imaps_993 tcp description Secure IMAP port-object eq 993 object-group service public_wifi_group description Service allowed on the Public Wifi Group. Allows Web and Email. service-object tcp-udp eq domain service-object tcp-udp eq www service-object tcp eq https service-object tcp-udp eq 993 service-object tcp eq imap4 service-object tcp eq 587 service-object tcp eq pop3 service-object tcp eq smtp access-list outside_access_in remark http traffic from outside access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www access-list outside_access_in remark ssh from outside to web1 access-list outside_access_in extended permit tcp any host XX.XX.XX.11 object-group ssh_2251 access-list outside_access_in remark ssh from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group ssh_2229 access-list outside_access_in remark http from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group http_8029 access-list outside_access_in remark ssh from outside to internal hosts access-list outside_access_in extended permit tcp any host XX.XX.XX.13 object-group DM_INLINE_TCP_1 access-list outside_access_in remark dns service to internal host access-list outside_access_in extended permit object-group TCPUDP any host XX.XX.XX.13 eq domain access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any access-list dmz_access_in extended permit tcp any host 192.168.10.29 object-group DM_INLINE_TCP_2 access-list public_access_in remark Web access to DMZ websites access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email) access-list public_access_in extended permit object-group public_wifi_group any any pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu public 1500 mtu dmz 1500 mtu inside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 60 global (outside) 1 interface global (dmz) 2 interface nat (public) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255 static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.13 192.168.10.10 netmask 255.255.255.255 dns static (dmz,outside) XX.XX.XX.11 192.168.10.30 netmask 255.255.255.255 dns static (dmz,inside) 192.168.0.29 192.168.10.29 netmask 255.255.255.255 static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns access-group outside_access_in in interface outside access-group public_access_in in interface public access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.9 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 20 console timeout 0 dhcpd dns 61.122.112.97 61.122.112.1 dhcpd auto_config outside ! dhcpd address 192.168.20.200-192.168.20.254 public dhcpd enable public ! dhcpd address 192.168.0.200-192.168.0.254 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 130.54.208.201 source public webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp !

  Read the article

• Problem installing Ubuntu 10.04 64 bit side by side with Vista by using a bootable USB drive. What n

  - by Adam Siddhi

  What happened I decided to install Ubuntu 10.04 64 bit side by side with Vista Home Premium (I guess on another partition) with a USB stick. I found instructions on how to do this here: https://help.ubuntu.com/community/Installation/FromUSBStick To create the bootable USB drive I had to download a program called Unetbootin. That process was simple enough. All I had to do was just choose the disk image option, select the ubuntu-10.04-desktop-amd64.iso image, make sure it recognizes my USB drive and then press OK. It takes only like a few minutes to create a working bootable USB drive. Then I have to restart my computer, enter the BIOS, select my USB drive as the first boot drive, save options and continue with booting up. After this Ubuntu actually loads up. I think this is known as the Live version of Ubuntu so you can try it out before fully installing it. Any ways, on the Ubuntu 10.04 desktop I saw an installer. I click it and begin the installation process. Just so you know, I tried installing it 2 times. I will explain what happened each time: The first time I tried installing Ubuntu 10.04 I got stuck at step 4 of 7. I remember selecting the last option in the window which was Specify Partitions Manually (Advanced) I made my partition for Ubuntu like 52 gigs. I clicked forward and a little pop up window appeared saying Please Wait. So the installation process stalled on this window so I closed out of it and quit the installation process. So at this point I was worried because I had already selected the partition size and assumed it started making it. Since it stalled I had to quit out though. Anyways, once again I reached step 4 of 7 a decided to select the first option which is Install them side by side choosing between them each startup. I figured this was the safe way to go. I did that and the pop up window saying Please Wait popped up again but lasted only like 10 seconds. Then I got to I guess step 6 where it asks you to enter your desired name and password. Did that and clicked forward. The Ubuntu 10.04 installation load screen appeared and the loading bar at the bottom started filling up. So I got to 83% and stalled during the Importing other profile information (I think it was called this. I had the option to do this during I think step 6) process. So at this point I decided to get stop the installation process. I was getting very nervous. I tried to restart the computer but all that happened was that Ubuntu restarted. I finally got the computer to restart. I was pretty sure I had screwed something up big time by this point. As my computer was restarting I entered BIOS again and switched back to it booting from my main hard drive containing Vista. Saved it and continued the boot process. My worst fears were confirmed as Vista would not boot up. I mean I saw the little Microsoft Windows choppy animated green loading bar at the bottom of the screen and then boom! It decided to restart. When it restarted I had the option to run a memory test check to see if there was anything that needed to be repaired. That took like 20 minutes and at the end I saw that I did indeed have to repair something. I had to go through 2 repair processes. After each I had to restart the computer. The 2nd time it went through the repair process it said that it could not fully repair the damage. I was scared and restarted but Vista did load up. I got to my desktop and saw a message saying something like Repairs have been made, Please restart for changes to take effect I noticed that some Notification icons were missing and I could not hear volume in a video. Things were a bit funky. So I did restart and here I am. Now what?! So since I got back into Vista and thankfully have a working Internet connection I am trying to find answers to my problem (that is why I am writing this post). I am scared that I have partioned my hard drive 2 times after researching Installing Ubuntu 10.04 and seeing this post http://techie-buzz.com/foss/ubuntu-10-04-lts-installation-guide.html The author shows screen shots of installing Ubuntu 10.04. He shows the image of step 4 of 7 with a caption at the bottom. I will recreate it below: Select a partitioning option. Unless you want to format all the hard drive and install Ubuntu afresh, select the last option and proceed. Questions If I have indeed partitioned my HD 2 times (which I am sure it is), how do I get to a point where I can see all my bad, unfinished Ubuntu partitions and get rid of them? How do I clean this big mess up? & How can I ensure that this mess will not happen next time I try installing Ubuntu 10.04? Thank you Adam

  Read the article

• puppet master REST API returns 403 when running under passenger works when master runs from command line

  - by Anadi Misra

  I am using the standard auth.conf provided in puppet install for the puppet master which is running through passenger under Nginx. However for most of the catalog, files and certitifcate request I get a 403 response. ### Authenticated paths - these apply only when the client ### has a valid certificate and is thus authenticated # allow nodes to retrieve their own catalog path ~ ^/catalog/([^/]+)$ method find allow $1 # allow nodes to retrieve their own node definition path ~ ^/node/([^/]+)$ method find allow $1 # allow all nodes to access the certificates services path ~ ^/certificate_revocation_list/ca method find allow * # allow all nodes to store their reports path /report method save allow * # unconditionally allow access to all file services # which means in practice that fileserver.conf will # still be used path /file allow * ### Unauthenticated ACL, for clients for which the current master doesn't ### have a valid certificate; we allow authenticated users, too, because ### there isn't a great harm in letting that request through. # allow access to the master CA path /certificate/ca auth any method find allow * path /certificate/ auth any method find allow * path /certificate_request auth any method find, save allow * path /facts auth any method find, search allow * # this one is not stricly necessary, but it has the merit # of showing the default policy, which is deny everything else path / auth any Puppet master however does not seems to be following this as I get this error on client [amisr1@blramisr195602 ~]$ sudo puppet agent --no-daemonize --verbose --server bangvmpllda02.XXXXX.com [sudo] password for amisr1: Starting Puppet client version 3.0.1 Warning: Unable to fetch my node definition, but the agent run will continue: Warning: Error 403 on SERVER: Forbidden request: XX.XXX.XX.XX(XX.XXX.XX.XX) access to /certificate_revocation_list/ca [find] at :110 Info: Retrieving plugin Error: /File[/var/lib/puppet/lib]: Failed to generate additional resources using 'eval_generate: Error 403 on SERVER: Forbidden request: XX.XXX.XX.XX(XX.XXX.XX.XX) access to /file_metadata/plugins [search] at :110 Error: /File[/var/lib/puppet/lib]: Could not evaluate: Error 403 on SERVER: Forbidden request: XX.XXX.XX.XX(XX.XXX.XX.XX) access to /file_metadata/plugins [find] at :110 Could not retrieve file metadata for puppet://devops.XXXXX.com/plugins: Error 403 on SERVER: Forbidden request: XX.XXX.XX.XX(XX.XXX.XX.XX) access to /file_metadata/plugins [find] at :110 Error: Could not retrieve catalog from remote server: Error 403 on SERVER: Forbidden request: XX.XXX.XX.XX(XX.XXX.XX.XX) access to /catalog/blramisr195602.XXXXX.com [find] at :110 Using cached catalog Error: Could not retrieve catalog; skipping run Error: Could not send report: Error 403 on SERVER: Forbidden request: XX.XXX.XX.XX(XX.XXX.XX.XX) access to /report/blramisr195602.XXXXX.com [save] at :110 and the server logs show XX.XXX.XX.XX - - [10/Dec/2012:14:46:52 +0530] "GET /production/certificate_revocation_list/ca? HTTP/1.1" 403 102 "-" "Ruby" XX.XXX.XX.XX - - [10/Dec/2012:14:46:52 +0530] "GET /production/file_metadatas/plugins?links=manage&recurse=true&&ignore=---+%0A++-+%22.svn%22%0A++-+CVS%0A++-+%22.git%22&checksum_type=md5 HTTP/1.1" 403 95 "-" "Ruby" XX.XXX.XX.XX - - [10/Dec/2012:14:46:52 +0530] "GET /production/file_metadata/plugins? HTTP/1.1" 403 93 "-" "Ruby" XX.XXX.XX.XX - - [10/Dec/2012:14:46:53 +0530] "POST /production/catalog/blramisr195602.XXXXX.com HTTP/1.1" 403 106 "-" "Ruby" XX.XXX.XX.XX - - [10/Dec/2012:14:46:53 +0530] "PUT /production/report/blramisr195602.XXXXX.com HTTP/1.1" 403 105 "-" "Ruby" thefile server conf file is as follows (and goin by what they say on puppet site, It is better to regulate access in auth.conf for reaching file server and then allow file server to server all) [files] path /apps/puppet/files allow * [private] path /apps/puppet/private/%H allow * [modules] allow * I am using server and client version 3 Nginx has been compiled using the following options nginx version: nginx/1.3.9 built by gcc 4.4.6 20120305 (Red Hat 4.4.6-4) (GCC) TLS SNI support enabled configure arguments: --prefix=/apps/nginx --conf-path=/apps/nginx/nginx.conf --pid-path=/apps/nginx/run/nginx.pid --error-log-path=/apps/nginx/logs/error.log --http-log-path=/apps/nginx/logs/access.log --with-http_ssl_module --with-http_gzip_static_module --add-module=/usr/lib/ruby/gems/1.8/gems/passenger-3.0.18/ext/nginx --add-module=/apps/Downloads/nginx/nginx-auth-ldap-master/ and the standard nginx puppet master conf server { ssl on; listen 8140 ssl; server_name _; passenger_enabled on; passenger_set_cgi_param HTTP_X_CLIENT_DN $ssl_client_s_dn; passenger_set_cgi_param HTTP_X_CLIENT_VERIFY $ssl_client_verify; passenger_min_instances 5; access_log logs/puppet_access.log; error_log logs/puppet_error.log; root /apps/nginx/html/rack/public; ssl_certificate /var/lib/puppet/ssl/certs/bangvmpllda02.XXXXXX.com.pem; ssl_certificate_key /var/lib/puppet/ssl/private_keys/bangvmpllda02.XXXXXX.com.pem; ssl_crl /var/lib/puppet/ssl/ca/ca_crl.pem; ssl_client_certificate /var/lib/puppet/ssl/certs/ca.pem; ssl_ciphers SSLv2:-LOW:-EXPORT:RC4+RSA; ssl_prefer_server_ciphers on; ssl_verify_client optional; ssl_verify_depth 1; ssl_session_cache shared:SSL:128m; ssl_session_timeout 5m; } Puppet is picking up the correct settings from the files mentioned because config print command points to /etc/puppet [amisr1@bangvmpllDA02 puppet]$ sudo puppet config print | grep conf async_storeconfigs = false authconfig = /etc/puppet/namespaceauth.conf autosign = /etc/puppet/autosign.conf catalog_cache_terminus = store_configs confdir = /etc/puppet config = /etc/puppet/puppet.conf config_file_name = puppet.conf config_version = "" configprint = all configtimeout = 120 dblocation = /var/lib/puppet/state/clientconfigs.sqlite3 deviceconfig = /etc/puppet/device.conf fileserverconfig = /etc/puppet/fileserver.conf genconfig = false hiera_config = /etc/puppet/hiera.yaml localconfig = /var/lib/puppet/state/localconfig name = config rest_authconfig = /etc/puppet/auth.conf storeconfigs = true storeconfigs_backend = puppetdb tagmap = /etc/puppet/tagmail.conf thin_storeconfigs = false I checked the firewall rules on this VM; 80, 443, 8140, 3000 are allowed. Do I still have to tweak any specifics to auth.conf for getting this to work?

  Read the article

• 500 Internal Server Error with PHP application

  - by James

  I have written a PHP application using Windows and XAMPP. I've been trying to run it on Ubuntu 10.10 with Lighttpd 1.4.26. Parts of the application work fine, but whenever I try to log in, I get a 500 - Internal Server Error page. The only thing that shows up in /var/log/lighttpd/error.log is 2011-02-25 13:43:13: (mod_fastcgi.c.2582) unexpected end-of-file (perhaps the fastcgi process died): pid: 1169 socket: unix:/tmp/php.socket-0 2011-02-25 13:43:13: (mod_fastcgi.c.3367) response not received, request sent: 1596 on socket: unix:/tmp/php.socket-0 for /~denton/customer-facing-portal/index.php?, closing connection If I had any output whatsoever from PHP, this would be a lot easier to debug. Any ideas on how to get some? Here is my /etc/lighttpd/lighttpd.conf file: # Debian lighttpd configuration file # ############ Options you really have to take care of #################### ## modules to load server.modules = ( "mod_alias", "mod_compress", # "mod_rewrite", # "mod_redirect", # "mod_usertrack", # "mod_expire", # "mod_flv_streaming", # "mod_evasive", "mod_setenv" ) ## a static document-root, for virtual-hosting take look at the ## server.virtual-* options server.document-root = "/var/www/" ## where to upload files to, purged daily. server.upload-dirs = ( "/var/cache/lighttpd/uploads" ) ## where to send error-messages to server.errorlog = "/var/log/lighttpd/error.log" ## files to check for if .../ is requested index-file.names = ( "index.php", "index.html", "index.htm", "default.htm", "index.lighttpd.html" ) ## Use the "Content-Type" extended attribute to obtain mime type if possible # mimetype.use-xattr = "enable" ## # which extensions should not be handle via static-file transfer # # .php, .pl, .fcgi are most often handled by mod_fastcgi or mod_cgi static-file.exclude-extensions = ( ".php", ".pl", ".fcgi" ) ######### Options that are good to be but not neccesary to be changed ####### ## Use ipv6 only if available. (disabled for while, check #560837) #include_shell "/usr/share/lighttpd/use-ipv6.pl" ## bind to port (default: 80) # server.port = 81 ## bind to localhost only (default: all interfaces) ## server.bind = "localhost" ## error-handler for status 404 #server.error-handler-404 = "/error-handler.html" #server.error-handler-404 = "/error-handler.php" ## to help the rc.scripts server.pid-file = "/var/run/lighttpd.pid" ## ## Format: <errorfile-prefix><status>.html ## -> ..../status-404.html for 'File not found' #server.errorfile-prefix = "/var/www/" ## virtual directory listings dir-listing.encoding = "utf-8" server.dir-listing = "enable" ### only root can use these options # # chroot() to directory (default: no chroot() ) #server.chroot = "/" ## change uid to <uid> (default: don't change) server.username = "www-data" ## change gid to <gid> (default: don't change) server.groupname = "www-data" #### compress module compress.cache-dir = "/var/cache/lighttpd/compress/" compress.filetype = ("text/plain", "text/html", "application/x-javascript", "text/css") #### url handling modules (rewrite, redirect, access) # url.rewrite = ( "^/$" => "/server-status" ) # url.redirect = ( "^/wishlist/(.+)" => "http://www.123.org/$1" ) #### expire module # expire.url = ( "/buggy/" => "access 2 hours", "/asdhas/" => "access plus 1 seconds 2 minutes") #### external configuration files ## mimetype mapping include_shell "/usr/share/lighttpd/create-mime.assign.pl" ## load enabled configuration files, ## read /etc/lighttpd/conf-available/README first include_shell "/usr/share/lighttpd/include-conf-enabled.pl" ## Set environment variables setenv.add-environment = ( "DB_URL__DEMO" => "192.168.1.231", "DB_NAME_DEMO" => "demo", "DB_USER_DEMO" => "user", "DB_PASS_DEMO" => "password", "DB_AGENCY_DEMO" => "demo" ) Here is my /etc/php5/cgi/php.ini file (sans 1641 lines of comments): [PHP] register_long_arrays = Off short_open_tag = Off engine = On short_open_tag = Off asp_tags = Off precision = 14 y2k_compliance = On output_buffering = 4096 zlib.output_compression = Off implicit_flush = Off unserialize_callback_func = serialize_precision = 100 allow_call_time_pass_reference = Off safe_mode = Off safe_mode_gid = Off safe_mode_include_dir = safe_mode_exec_dir = safe_mode_allowed_env_vars = PHP_ safe_mode_protected_env_vars = LD_LIBRARY_PATH disable_functions = disable_classes = expose_php = On max_execution_time = 30 max_input_time = 60 memory_limit = 128M error_reporting = E_ALL & ~E_DEPRECATED & ~E_STRICT display_errors = On display_startup_errors = On log_errors = On log_errors_max_len = 1024 ignore_repeated_errors = Off ignore_repeated_source = Off report_memleaks = On track_errors = On html_errors = On variables_order = "GPCS" request_order = "GP" register_globals = Off register_long_arrays = Off register_argc_argv = Off auto_globals_jit = On post_max_size = 8M magic_quotes_gpc = Off magic_quotes_runtime = Off magic_quotes_sybase = Off auto_prepend_file = auto_append_file = default_mimetype = "text/html" doc_root = user_dir = enable_dl = Off cgi.fix_pathinfo=1 file_uploads = On upload_max_filesize = 2M max_file_uploads = 20 allow_url_fopen = On allow_url_include = Off default_socket_timeout = 60 [Date] date.timezone = "America/Chicago" [filter] [iconv] [intl] [sqlite] [sqlite3] [Pcre] [Pdo] [Pdo_mysql] pdo_mysql.cache_size = 2000 pdo_mysql.default_socket= [Phar] [Syslog] define_syslog_variables = Off [mail function] SMTP = localhost smtp_port = 25 mail.add_x_header = On [SQL] sql.safe_mode = Off [ODBC] odbc.allow_persistent = On odbc.check_persistent = On odbc.max_persistent = -1 odbc.max_links = -1 odbc.defaultlrl = 4096 odbc.defaultbinmode = 1 [Interbase] ibase.allow_persistent = 1 ibase.max_persistent = -1 ibase.max_links = -1 ibase.timestampformat = "%Y-%m-%d %H:%M:%S" ibase.dateformat = "%Y-%m-%d" ibase.timeformat = "%H:%M:%S" [MySQL] mysql.allow_local_infile = On mysql.allow_persistent = On mysql.cache_size = 2000 mysql.max_persistent = -1 mysql.max_links = -1 mysql.default_port = mysql.default_socket = mysql.default_host = mysql.default_user = mysql.default_password = mysql.connect_timeout = 60 mysql.trace_mode = Off [MySQLi] mysqli.max_persistent = -1 mysqli.allow_persistent = On mysqli.max_links = -1 mysqli.cache_size = 2000 mysqli.default_port = 3306 mysqli.default_socket = mysqli.default_host = mysqli.default_user = mysqli.default_pw = mysqli.reconnect = Off [mysqlnd] mysqlnd.collect_statistics = On mysqlnd.collect_memory_statistics = Off [OCI8] [PostgresSQL] pgsql.allow_persistent = On pgsql.auto_reset_persistent = Off pgsql.max_persistent = -1 pgsql.max_links = -1 pgsql.ignore_notice = 0 pgsql.log_notice = 0 [Sybase-CT] sybct.allow_persistent = On sybct.max_persistent = -1 sybct.max_links = -1 sybct.min_server_severity = 10 sybct.min_client_severity = 10 [bcmath] bcmath.scale = 0 [browscap] [Session] session.save_handler = files session.use_cookies = 1 session.use_only_cookies = 1 session.name = PHPSESSID session.auto_start = 0 session.cookie_lifetime = 0 session.cookie_path = / session.cookie_domain = session.cookie_httponly = session.serialize_handler = php session.gc_probability = 1 session.gc_divisor = 1000 session.gc_maxlifetime = 1440 session.bug_compat_42 = Off session.bug_compat_warn = Off session.referer_check = session.entropy_length = 0 session.cache_limiter = nocache session.cache_expire = 180 session.use_trans_sid = 0 session.hash_function = 0 session.hash_bits_per_character = 5 url_rewriter.tags = "a=href,area=href,frame=src,input=src,form=fakeentry" [MSSQL] mssql.allow_persistent = On mssql.max_persistent = -1 mssql.max_links = -1 mssql.min_error_severity = 10 mssql.min_message_severity = 10 mssql.compatability_mode = Off mssql.secure_connection = Off [Assertion] [COM] [mbstring] [gd] [exif] [Tidy] tidy.clean_output = Off [soap] soap.wsdl_cache_enabled=1 soap.wsdl_cache_dir="/tmp" soap.wsdl_cache_ttl=86400 soap.wsdl_cache_limit = 5 [sysvshm] [ldap] ldap.max_links = -1 [mcrypt] [dba] Update: here is /etc/lighttpd/conf-enabled/15-fastcgi-php.conf As far as I know, it's just the default config file the Ubuntu package installed. ## FastCGI programs have the same functionality as CGI programs, ## but are considerably faster through lower interpreter startup ## time and socketed communication ## ## Documentation: /usr/share/doc/lighttpd-doc/fastcgi.txt.gz ## http://redmine.lighttpd.net/projects/lighttpd/wiki/Docs:ConfigurationOptions#mod_fastcgi-fastcgi ## Start an FastCGI server for php (needs the php5-cgi package) fastcgi.server += ( ".php" => (( "bin-path" => "/usr/bin/php-cgi", "socket" => "/tmp/php.socket", "max-procs" => 1, "idle-timeout" => 20, "bin-environment" => ( "PHP_FCGI_CHILDREN" => "4", "PHP_FCGI_MAX_REQUESTS" => "10000" ), "bin-copy-environment" => ( "PATH", "SHELL", "USER" ), "broken-scriptfilename" => "enable" )) )

  Read the article

• squid3 auth thru samba using ntlm to AD doesn't work

  - by derty

  some users here are spending to much time exploring the WWW. So big boss whats to get this under control. We use a squid3 just for some security reason and chace benefits. and now i'm trying to set up a new proxy on a different server (Debian 6) Permissions are defined in AC and the squid3 should get the auth thru samba/winbind by using the ntlm protocol. but i'll get all the time Access, denited. it only works by using LDAP but thats not the way i need it. here some log and confs squid access.log 1326878095.784 1 192.168.15.27 TCP_DENIED/407 4049 GET http://at.msn.com/? -NONE/- text/html 1326878095.791 1 192.168.15.27 TCP_DENIED/407 4294 GET http://at.msn.com/? - NONE/- text/html 1326878095.803 9 192.168.15.27 TCP_DENIED/403 4028 GET http://at.msn.com/? kavan NONE/- text/html 1326878095.848 0 192.168.15.27 TCP_DENIED/403 3881 GET http://www.squid-cache.org/Artwork/SN.png kavan NONE/- text/html 1326878100.279 0 192.168.15.27 TCP_DENIED/403 3735 GET http://www.google.at/ kavan NONE/- text/html 1326878100.296 0 192.168.15.27 TCP_DENIED/403 3870 GET http://www.squid-cache.org/Artwork/SN.png kavan NONE/- text/html 1326878155.700 0 192.168.15.27 TCP_DENIED/407 4072 GET http://ie9cvlist.ie.microsoft.com/IE9CompatViewList.xml - NONE/- text/html 1326878155.705 2 192.168.15.27 TCP_DENIED/407 4317 GET http://ie9cvlist.ie.microsoft.com/IE9CompatViewList.xml - NONE/- text/html 1326878155.709 3 192.168.15.27 TCP_DENIED/403 4026 GET http://ie9cvlist.ie.microsoft.com/IE9CompatViewList.xml kavan NONE/- text/html squid chace 2012/01/18 10:12:49| Creating Swap Directories 2012/01/18 10:12:49| Starting Squid Cache version 3.1.6 for x86_64-pc-linux-gnu... 2012/01/18 10:12:49| Process ID 17236 2012/01/18 10:12:49| With 65535 file descriptors available 2012/01/18 10:12:49| Initializing IP Cache... 2012/01/18 10:12:49| DNS Socket created at [::], FD 7 2012/01/18 10:12:49| DNS Socket created at 0.0.0.0, FD 8 2012/01/18 10:12:49| Adding nameserver 192.168.15.2 from /etc/resolv.conf 2012/01/18 10:12:49| Adding nameserver 192.168.15.19 from /etc/resolv.conf 2012/01/18 10:12:49| Adding nameserver 192.168.15.1 from /etc/resolv.conf 2012/01/18 10:12:49| Adding domain schoenbrunn.local from /etc/resolv.conf 2012/01/18 10:12:49| helperOpenServers: Starting 5/5 'squid_ldap_auth' processes 2012/01/18 10:12:49| helperOpenServers: Starting 10/10 'ntlm_auth' processes 2012/01/18 10:12:49| helperOpenServers: Starting 10/10 'squid_kerb_auth' processes 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| helperOpenServers: Starting 5/5 'squid_ldap_group' processes 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| Unlinkd pipe opened on FD 73 2012/01/18 10:12:49| Local cache digest enabled; rebuild/rewrite every 3600/3600 sec 2012/01/18 10:12:49| Store logging disabled 2012/01/18 10:12:49| Swap maxSize 0 + 262144 KB, estimated 20164 objects 2012/01/18 10:12:49| Target number of buckets: 1008 2012/01/18 10:12:49| Using 8192 Store buckets 2012/01/18 10:12:49| Max Mem size: 262144 KB 2012/01/18 10:12:49| Max Swap size: 0 KB 2012/01/18 10:12:49| Using Least Load store dir selection 2012/01/18 10:12:49| Set Current Directory to /var/spool/squid3 2012/01/18 10:12:49| Loaded Icons. 2012/01/18 10:12:49| Accepting HTTP connections at [::]:3128, FD 74. 2012/01/18 10:12:49| HTCP Disabled. 2012/01/18 10:12:49| Squid modules loaded: 0 2012/01/18 10:12:49| Adaptation support is off. 2012/01/18 10:12:49| Ready to serve requests. 2012/01/18 10:12:50| storeLateRelease: released 0 objects smb.conf # Domain Authntication Settings workgroup = <WORKGROUP> security = ads password server = <DOMAINNAME>.LOCAL realm = <DOMAINNAME>.LOCAL ldap ssl = no # logging log level = 5 max log size = 50 # logs split per machine log file = /var/log/samba/%m.log # max 50KB per log file, then rotate ; max log size = 50 # User settings username map = /etc/samba/smbusers idmap uid = 10000-20000000 idmap gid = 10000-20000000 idmap backend = ad ; template primary group = <ad group> template shell = /sbin/nologin # Winbind Settings winbind separator = + winbind enum users = Yes winbind enum groups = Yes winbind netsted groups = Yes winbind nested groups = Yes winbind cache time = 10 winbind use default domain = Yes #Other Globals unix charset = LOCALE server string = <SERVERNAME> load printers = no printing = cups cups options = raw ; printcap name = /etc/printcap #obtain list of printers automatically on SystemV ; printcap name = lpstat ; printing = cups squid.conf auth_param ntlm program /usr/bin/ntlm_auth --require-membership-of=<DOMAINNAME>\\INTERNETZ --helper-protocol=squid-2.5-ntlmssp auth_param ntlm children 10 auth_param basic program /usr/lib/squid3/squid_ldap_auth -R -b "dc=<dcname>,dc=local" -D "cn=administrator,cn=Users,dc=<domainname>,dc=local" -w "******" -f sAMAccountName=%s -h 192.168.15.19:3268 auth_param basic realm "Proxy Authentifizierung. Bitte geben Sie Ihren Benutzername und Ihr Passwort ein!" #means insert you PW in an other language - # external_acl_type InetGroup %LOGIN /usr/lib/squid3/squid_ldap_group -R -b "dc=<domainname>,dc=local" -D "cn=administrator,cn=Users,dc=<domainname>,dc=local" -w "******" -f "(&(objectclass=person)(sAMAccountName=%v) (memberof=cn=%a,cn=internetz,dc=<domainname>,dc=local))" -h 192.168.15.19:3268 auth_param negotiate program /usr/lib/squid3/squid_kerb_auth -d auth_param negotiate children 10 auth_param negotiate keep_alive on acl localnet proxy_auth REQUIRED acl InetAccess external InetGroup Internetz http_access allow InetAccess http_access deny all acl auth proxy_auth REQUIRED http_access allow auth and a very suspicious is that by adding the proxy server to the Domain i see 2 new entries in the PC one with the original computer-name leopoldine and one with leopoldine CNF:f8efa4c4-ff0e-4217-939d-f1523b43464d ?!? I tried a lot, really... but i stuck on this problem... i actually i even reinstalled all dependent programs and reconfigured them from default. Group exists and has me in it. Firefox running on the old proxy and i use IE for testing the new one. But i'll get all the time Access-Denited and to be honest i'm quite a beginner, so please don't be to prude. I'll interested in improving, i'll get the information we need to fix this but i started working 2 month ago and got only 1 1/2 year's training and not a single sec. in linux ;)

  Read the article

• Bandwidth Limit User

  - by user45611

  Hello, i'm saxtor i would like to know how to limit users bandwidth for 10gb per day however i dont want to limit them by ipaddress because if they where to go to an internet cafe the users at the cafe will be restricted with that quota, i need to log them via sockets, example the user request to download a file from http://localhost with there username and password, when they download the file sql will update there bandwidth they used, i have a script here but its not working my buffer doesnt work that rate when a user uses multiple connections thanks for the help!. /** * @author saxtor if you can improve this code email me @saxtorinc.com * @copyright 2010 / /* * CREATE TABLE IF NOT EXISTS max_traffic ( id int(255) NOT NULL AUTO_INCREMENT, limit int(255) NOT NULL, PRIMARY KEY (id) ) ENGINE=MyISAM DEFAULT CHARSET=latin1 AUTO_INCREMENT=0 ; */ //SQL Connection [this is hackable for testing] date_default_timezone_set("America/Guyana"); mysql_connect("localhost", "root", "") or die(mysql_error()); mysql_select_db("Quota") or die(mysql_error()); function quota($id) { $result = mysql_query("SELECT `limit` FROM max_traffic WHERE id='$id' ") or die(error_log(mysql_error()));; $row = mysql_fetch_array($result); return $row[0]; } function update_quota($id,$value) { $result = mysql_query("UPDATE `max_traffic` SET `limit`='$value' WHERE id='$id'") or die(mysql_error()); return $value; } if ( quota(1) != 0) $limit = quota(1); else $limit = 0; $multipart = false; //was a part of the file requested? (partial download) $range = $_SERVER["HTTP_RANGE"]; if ($range) { //pass client Range header to rapidshare // _insert($range); $cookie .= "\r\nRange: $range"; $multipart = true; header("X-UR-RANGE-Range: $range"); } $url = 'http://127.0.0.1/puppy.iso'; $filename = basename($url); //octet-stream + attachment = client always stores file header('Content-type: application/octet-stream'); header('Content-Disposition: attachment; filename="'.$filename.'"'); //always included so clients know this script supports resuming header("Accept-Ranges: bytes"); //awful hack to pass rapidshare the premium cookie $user_agent = ini_get("user_agent"); ini_set("user_agent", $user_agent . "\r\nCookie: enc=$cookie"); $httphandle = fopen($url, "r"); $headers = stream_get_meta_data($httphandle); $size = $headers["wrapper_data"][6]; $sizer = explode(' ',$size); $size = $sizer[1]; //let's check the return header of rapidshare for range / length indicators //we'll just pass these to the client foreach ($headers["wrapper_data"] as $header) { $header = trim($header); if (substr(strtolower($header), 0, strlen("content-range")) == "content-range") { // _insert($range); header($header); header("X-RS-RANGE-" . $header); $multipart = true; //content-range indicates partial download } elseif (substr(strtolower($header), 0, strlen("Content-Length")) == "content-length") { // _insert($range); header($header); header("X-RS-CL-" . $header); } } if ($multipart) header('HTTP/1.1 206 Partial Content'); flush(); $speed = 4128; $packet = 1; //this is private dont touch. $bufsize = 128; //this is private dont touch/ $bandwidth = 0; //this is private dont touch. while (!(connection_aborted() || connection_status() == 1) && $size > 0) { while (!feof($httphandle) && $size > 0) { if ($limit <= 0 ) $size = 0; if ( $size < $bufsize && $size != 0 && $limit != 0) { echo fread($httphandle,$size); $bandwidth += $size; } else { if( $limit != 0) echo fread($httphandle,$bufsize); $bandwidth += $bufsize; } $size -= $bufsize; $limit -= $bufsize; flush(); if ($speed > 0 && ($bandwidth > $speed*$packet*103)) { usleep(100000); $packet++; //update_quota(1,$limit); } error_log(update_quota(1,$limit)); $limit = quota(1); //if( $size <= 0 ) // exit; } fclose($httphandle); } exit; ?

  Read the article

• Windows installation repair option not showing up

  - by Carl

  I'm trying to repair an existing Windows XP installation. Following the instructions from http://www.microsoft.com/windowsxp/using/helpandsupport/learnmore/tips/doug92.mspx this should work: When the Press any key to boot from CD message is displayed on your screen, press a key to start your computer from the Windows XP CD. Press ENTER when you see the message To setup Windows XP now, and then press ENTER displayed on the Welcome to Setup screen. Do not choose the option to press R to use the Recovery Console. In the Windows XP Licensing Agreement, press F8 to agree to the license agreement. Make sure that your current installation of Windows XP is selected in the box, and then press R to repair Windows XP. Follow the instructions on the screen to complete Setup. On step 5 pressing R does nothing and there is nothing on the screen saying it would. When I just select to install I get a message that a previous installation is there and proceeding will destroy it and installed applications, I can optionally select a directory other than c:\windows, and I can optionally format before continuing. I had tried to go from SP2-SP3. It failed, and then I couldn't get to Safe Mode. I put the SP1 disk back in to do a repair, and I don't see that option. (I don't have an SP2 boot/install disk, I just have the non-boot upgrade package.) UPDATE: Upon loading the Recovery Console, I get a message saying The system registry does not appear to have an active ControlSet key. The system registry may be damaged. You can try restarting it with the Last Known Good configuration or you can try repairing the installation of Windows using the setup program's repair and recovery options. I then did bootcfg /scan - "successful" ... Total installs: 1 ... [1] c:\windows - with the c:\windows command prompt below it. bootcfg /list gives [1] Windows XP Pro; OS Load Options /noexecute=optin /fastdetect; OS Location: c:\windows I followed the instructions at http://michaelstevenstech.com/XPrepairinstall.htm - "Warning 2" link copy E:\i386\ntldr C:\ copy E:\i386\ntdetect.com C:\ attrib -h -r -s C:\boot.ini del C:\boot.ini BootCfg /Rebuild I added /fastdetect when it asked for options. I re-ran Windows setup - no change - no repair option. UPDATE: I followed the procedure at http://support.microsoft.com/default.aspx?scid=kb;en-us;307545 I rebooted. I now get a quick message on bootup to select the boot - 1: [blank] ; Windows XP Professional ; Windows Recover Console. The "1: " is new. The rest is the way it was when all was okay. Selecting 1: and the next one gives the same result - I get to a login icon, and then it asks for a password, with the blinking cursor, but I can't type anything. I reboot with the Windows CD. Now I see a repair option for installation "1: " I selected R on that, and it did "Setup is copying files..." and rebooted when it was done. Then it booted, and I got a window saying "Setup will complete in approximately 39 minutes." That's where I am now. I wasn't expecting this last part - I did a repair several months ago and I don't recall that. UPDATE: Booted up. Asked if I wanted to register Windows online. All my icons are there, and the old desktop documents. Good. All the applications I tried from the Start Menu work (tested a few), except Corel Photopaint - I get registry entry not found errors. Windows ran for a while, then froze. The mouse and keyboard don't work. Pressing the power button got Windows to shut down. I probably need to put SP2 on it, and then all the updates for my laptop for XP Pro SP2 (drivers), there's a bunch. The mouse and keyboard quit working again. That wasn't a problem when I first set up this laptop. I've ran 4 times now. Two mouse/keyboards hangs by pressing Ctrl-C (to copy text from a notepad document), and two by selecting Start-Run (wasn't able to type anything in the box).

  Read the article

• Why did my flash drive become "read only" and (how) can I fix it?

  - by Bob

  I have a brand new flash drive (one week old) that has become marked as read only, by Windows, Kubuntu and a bootable partitioner. Why did this happen? Is it fixable? If it is, how can I fix this? The problem Firstly, this drive is new. It's certainly not been used enough to die from normal wear and tear, though I would not discount defective components. The drive itself has somehow become locked in a read only state. Windows' Disk management: Diskpart: Generic Flash Disk USB Device Disk ID: 33FA33FA Type : USB Status : Online Path : 0 Target : 0 LUN ID : 0 Location Path : UNAVAILABLE Current Read-only State : Yes Read-only : No Boot Disk : No Pagefile Disk : No Hibernation File Disk : No Crashdump Disk : No Clustered Disk : No What really confuses me is Current Read-only State : Yes and Read-only : No. Attempted solutions So far, I've tried: Formatting it in Windows (in Disk management, the format options are greyed out when right clicking). DiskPart Clean (CLEAN - Clear the configuration information, or all information, off the disk.): DISKPART> clean DiskPart has encountered an error: The media is write protected. See the System Event Log for more information. There was nothing in the event log. Windows command line format >format G: Insert new disk for drive G: and press ENTER when ready... The type of the file system is FAT32. Verifying 7740M Cannot format. This volume is write protected. Windows chkdsk: see below for details Kubuntu fsck (through VirtualBox USB passthrough): see below for details Acronis True Image to format, to convert to GPT, to destroy and rebuild MBR, basically anything: failed (could not write to MBR) Details (and a nice story) Background This was a brand new, generic, 8GB flash drive I wanted to create a multiboot flash drive with. It came formatted as FAT32, though oddly a little larger than most 8 GIGAbyte flash drives I've come across. Approximately 127MB was listed as "used" by Windows. I never discovered why. The end usable space was about what I normally expect from a 8GB drive (approx 7.4 GIBIbytes). I had thrown quite a few Linux distros on, along with a copy of Hiren's. They would all boot perfectly. They were put on with YUMI. When I tried to put the Knoppix DVD on, YUMI added an odd video option to its boot comman which caused Knoppix to boot with a black screen on X. ttys 1 through 6 still worked as text only interfaces. A few days later, I took some time to take that odd video option off, making the boot command match the one that comes with Knoppix. On the attempt to boot, Knoppix reported some form of LZMA corruption. Leading up to the current issue I was thinking the Knoppix files may have been corrupted somehow, so I tried reloading it. The drive was nearly full (45MB free), so I deleted a generic ISO that also was not booting. That went fine. I then went through YUMI to 'uninstall' Knoppix, i.e. delete files and remove from the menus. The files went first, then the menus were cleared successfully. However, the free space was stuck at about 700MB, same as it was before removing Knoppix. In the old Knoppix folder, there was a 0 byte file named KNOPPIX that could not be deleted. I tried reinserting the drive to delete this file - without safely removing, if that made a difference (hey, first time for everything). Running the standard Windows chkdsk scan without /r or /f reported errors found. Running with /r just got it stuck. I decided to give fsck a shot, so I loaded up my Kubuntu VM and attached the drive to it with VirtualBox's USB 2.0 passthrough. I umounted it (/dev/sda1) and ran a fsck. There are differences between boot sector and its backup. I chose No action. It told me FATs differ and asked me to select either the first or second FAT. Whichever I selected, I got a notice of Free cluster summary wrong. If I chose Correct, it gave a list of incorrect file names. To try to fix something, at least, I ran it with the -p option. Halfway through fixing the files, the VM froze - I ended its process about ten minutes later. Cause? My next attempt was to use YUMI, again, to rebuild the whole drive. I used YUMI's built in reformat (to FAT32) option and installed a Kubuntu ISO (700MB). The format was successful, however, the extract and copy of Kubuntu (which YUMI uses a 7zip binary for) froze at about 60% done. After waiting for about fifteen minutes (longer than the 3.5GB Knoppix ISO took last time), I pulled the drive out. The drive at this point was already formatted, SYSLINUX already installed, just waiting on the unpacking of an ISO and the modifying of the boot menus. Plugging it back in, it came up as normal - however, any write action would fail. Disk management reported it as read only. On reconnect, it would come up as normal but a write operation would cause it to go read only again. After a few attempts, it started coming up as read only on insertion. Attempts to fix This is when I ran through the attempts listed above, to try and reformat it in case of a faulty format. However the inability to do so even on a bootable disk indicated something more serious is wrong. chkdsk now reports nothing is wrong, and fsck still reports MBR inconsistencies, but now always chooses first FAT automatically after telling me FATs differ. It still does the same Free cluster summary wrong afterwards. I cannot run with -p anymore because it is now marked as read only. It also managed to corrupt my VM's disk somehow on the first attempt (yes, I'm sure I chose sda, which is mapped to a 7.4GB drive - I triple checked). Thank god for snapshots? I'm just about out of ideas. To my inexperienced mind it looks like something in the drive's firmware set it to read only "permanently" somehow - is there any way to reset this? I don't particularly care about keeping data, considering I've reformatted it twice. Also, fixes that keep me in Windows are better; it reduces the risk of me accidentally nuking my main hard drive. Update 1: I pulled apart the drive out of curiosity. As you can see, there are no obvious write protect switches. There is an IC on the other side, ALCOR branded labelled AU6989HL, if that matters. If there appears to be no way to fix this, I'll probably pull out the (glued down) card and put it in a card reader to check if it's the card or the controller that died. Update 2: I've pulled the card off, Windows detects the drive as a card reader now. The contacts on the card don't appear to be used, and there are several rows of holes on the card itself. Putting it into the card reader only detects about 30MB total, RAW. It's probably either the reader incorrectly reporting the card as faulty (as if a real SD card's write protect was switched on) or a bad contact somewhere. If nothing else, I have a spare 8GB Micro SD card now... as soon as I figure out how to format it as 8GB.

  Read the article

• Three ways to upload/post/convert iMovie to YouTube [closed]

  - by alexyu2010

  For Mac users, iMovie is probably a convenient tool for making, editing their own home movies so as to upload to YouTube for sharing with more people. However, uploading iMovie files to YouTube can't be always a smooth run, I did notice many people complaining about it. This article is delivered for guiding those who are haunted by the nightmare by providing three common ways to upload iMovie files to YouTube. YouTube and iMovie YouTube is the most popular video sharing website for users to upload, share and view videos. It empowers anyone with an Internet connection the ability to upload video clips and share them with friends, family and the world. Users are invited to leave comments, pick favourites, send messages to each other and watch videos sorted into subjects and channels. YouTube accepts videos uploaded in most container formats, including WMV (Windows Media Video), 3GP (Cell Phones), AVI (Windows), MOV (Mac), MP4 (iPod/PSP), FLV (Adobe Flash), MKV (H.264). These include video codecs such as MP4, MPEG and WMV. iMovie is a common video editing software application comes with every Mac for users to edit their own home movies. It imports video footage to the Mac using either the Firewire interface on most MiniDV format digital video cameras, the USB port, or by importing the files from a hard drive where users can edit the video clips, add titles, and add music. Since 1999, eight versions of iMovie have been released by Apple, each with its own functions and characteristic, and each of them deal with videos in a way more or less different. But the most common formats handled with iMovie if specialty discarded as far as to my research are MOV, DV, HDV, MPEG-4. Three ways for successful upload iMovie files to YouTube Solution one and solution two suitable for those who are 100 certainty with their iMovie files which are fully compatible with YouTube. For smooth uploading, you are required to get a YouTube account first. Solution 1: Directly upload iMovie to YouTube Step 1: Launch iMovie, select the project you want to upload in YouTube. Step 2: Go to the file menu, click Share, select Export Movie Step 3: Specify the output file name and directory and then type the video type and video size. Solution 2: Post iMovie to YouTube straightly Step 1: Launch iMovie, choose the project you want to post in YouTube Step 2: From the Share menu, choose YouTube Step 3: In the pop-up YouTube windows, specify the name of your YouTube account, the password, choose the Category and fill in the description and tags of the project. Tick Make this movie more private on the bottom of the window, if possible, to limit those who can view the project. Click Next, and then click Publish. iMovie will automatically export and upload the movie to YouTube. Step 4: Click Tell a Friend to email friends and your family about your film. You are also allowed to copy the URL from Tell a Friend window and paste it into an email you created in your favourite email application if you like. Anyone you send to email to will be able to follow the URL directly to your movie. Note: Videos uploaded to YouTube are limited to ten minutes in length and a file size of 2GB. Solution 3: Upload to iMovie after conversion If neither of the above mentioned method works, there is still a third way to turn to. Sometimes, your iMovie files may not be recognized by YouTube due to the versions of iMovie (settings and functions may varies among versions), video itself (video format difference because of file extension, resolution, video size and length), compatibility (videos that are completely incompatible with YouTube). In this circumstance, the best and reliable method is to convert your iMovie files to YouTube accepted files, iMovie to YouTube converter will be inevitably the ideal choice. iMovie to YouTube converter is an elaborately designed tool for convert iMovie files to YouTube workable WMV, 3GP, AVI, MOV, MP4, FLV, MKV for smooth uploading with hard-to-believe conversion speed and second to none output quality. It can also convert between almost all popular popular file formats like AVI, WMV, MPG, MOV, VOB, DV, MP4, FLV, 3GP, RM, ASF, SWF, MP3, AAC, AC3, AIFF, AMR, WAV, WMA etc so as to put on various portable devices, import to video editing software or play on vast amount video players. iMovie to YouTube converter can also served as an excellent video editing tool to meet your specific program requirements. For example, you can cut your video files to a certain length, or split your video files to smaller ones and select the proper resolution suitable for demands of YouTube by Clip or Settings separately. Crop allows you to cut off unwanted black edges from your videos. Besides, you can also have a good command of the whole process or snapshot your favourite pictures from the preview window. More can be expected if you have a try.

  Read the article

• Server randomly freezes

  - by PsySkeletor

  Im facing a very strange issue, my debian squeeze freezes up always at night (Berlin, time). Here is what i get from a time and after doing this a few times, it becomes frozen and must be hard-reset. From /var/log/messages Dec 11 01:36:11 srv156 kernel: [125983.204251] CPU 1: Dec 11 01:36:11 srv156 kernel: [125983.204251] Modules linked in: xt_multiport nf_conntrack_ipv4 nf_defrag_ipv4 xt_recent xt_state nf_conntrack xt_tcpudp iptable_filter ip_tables x_tables hwmon_vid snd_hda_codec_atihdmi snd_hda_intel snd_hda_codec snd_hwdep snd_pcm radeon snd_timer ttm drm_kms_helper snd k10temp i2c_piix4 soundcore snd_page_alloc edac_core parport_pc drm i2c_algo_bit i2c_core shpchp pci_hotplug pcspkr edac_mce_amd parport wmi evdev processor button ext3 jbd mbcache raid1 md_mod sd_mod crc_t10dif ata_generic ahci ohci_hcd pata_atiixp e100 mii libata xhci floppy ehci_hcd thermal thermal_sys usbcore scsi_mod nls_base [last unloaded: i2c_dev] Dec 11 01:36:11 srv156 kernel: [125983.204251] Pid: 758, comm: flush-9:0 Tainted: G B 2.6.32-5-amd64 #1 GA-78LMT-USB3 Dec 11 01:36:11 srv156 kernel: [125983.204251] RIP: 0010:[<ffffffff810b3506>] [<ffffffff810b3506>] find_get_pages_tag+0x66/0xdd Dec 11 01:36:11 srv156 kernel: [125983.204251] RSP: 0018:ffff8804235e7b30 EFLAGS: 00000286 Dec 11 01:36:11 srv156 kernel: [125983.204251] RAX: ffffffffffffffff RBX: ffff8804235e7c00 RCX: 0000000000000000 Dec 11 01:36:11 srv156 kernel: [125983.204251] RDX: 0000000000040000 RSI: ffffea000496b2a8 RDI: ffffea000496b2a0 Dec 11 01:36:11 srv156 kernel: [125983.204251] RBP: ffffffff8101166e R08: ffff8804235e7af0 R09: 0000000000000000 Dec 11 01:36:11 srv156 kernel: [125983.204251] R10: 0000000000000000 R11: 0000000000040000 R12: ffff8804235e7c08 Dec 11 01:36:11 srv156 kernel: [125983.204251] R13: 0000000d22678a20 R14: ffff8804235e7af0 R15: 00000000091b9060 Dec 11 01:36:11 srv156 kernel: [125983.204251] FS: 0000000000000000(0000) GS:ffff880010440000(0000) knlGS:000000007ebf7b70 Dec 11 01:36:11 srv156 kernel: [125983.204522] CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b Dec 11 01:36:11 srv156 kernel: [125983.204522] CR2: 00000000dec86000 CR3: 0000000001001000 CR4: 00000000000006e0 Dec 11 01:36:11 srv156 kernel: [125983.204522] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 Dec 11 01:36:11 srv156 kernel: [125983.204522] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Dec 11 01:36:11 srv156 kernel: [125983.204522] Call Trace: Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff810bb792>] ? pagevec_lookup_tag+0x1a/0x21 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff810ba330>] ? write_cache_pages+0x162/0x327 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff810b9d48>] ? __writepage+0x0/0x25 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff8110758a>] ? writeback_single_inode+0xe7/0x2da Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff81108290>] ? writeback_inodes_wb+0x424/0x4ff Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff81108497>] ? wb_writeback+0x12c/0x1ab Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff8110870d>] ? wb_do_writeback+0x14f/0x165 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff81108754>] ? bdi_writeback_task+0x31/0xaa Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff810c8664>] ? bdi_start_fn+0x0/0xd0 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff810c86d4>] ? bdi_start_fn+0x70/0xd0 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff810c8664>] ? bdi_start_fn+0x0/0xd0 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff81064ac1>] ? kthread+0x79/0x81 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff81011baa>] ? child_rip+0xa/0x20 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff81064a48>] ? kthread+0x0/0x81 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff81011ba0>] ? child_rip+0x0/0x20 From /var/log/syslog Dec 10 21:20:29 srv156 kernel: [110625.162930] BUG: Bad page map in process java pte:14fa4f067 pmd:424b54067 Dec 10 21:20:29 srv156 kernel: [110625.162937] page:ffffea000496c148 flags:0200000000000878 count:2 mapcount:-1 mapping:ffff88014f8d7de8 index:2f4 Dec 10 21:20:29 srv156 kernel: [110625.162946] addr:0000000009096000 vm_flags:00100077 anon_vma:ffff880422410d40 mapping:(null) index:9096 Dec 10 21:20:29 srv156 kernel: [110625.162955] Pid: 21356, comm: java Tainted: G B 2.6.32-5-amd64 #1 Dec 10 21:20:29 srv156 kernel: [110625.162961] Call Trace: Dec 10 21:20:29 srv156 kernel: [110625.162966] [<ffffffff810ca4bf>] ? print_bad_pte+0x232/0x24a Dec 10 21:20:29 srv156 kernel: [110625.162973] [<ffffffff810cb56f>] ? unmap_vmas+0x62d/0x931 Dec 10 21:20:29 srv156 kernel: [110625.162980] [<ffffffff810cfc74>] ? exit_mmap+0xc4/0x148 Dec 10 21:20:29 srv156 kernel: [110625.162986] [<ffffffff8104bbc1>] ? mmput+0x3c/0xdf Dec 10 21:20:29 srv156 kernel: [110625.162992] [<ffffffff8104f81e>] ? exit_mm+0x102/0x10d Dec 10 21:20:29 srv156 kernel: [110625.162998] [<ffffffff81051243>] ? do_exit+0x1f8/0x6c9 Dec 10 21:20:29 srv156 kernel: [110625.163004] [<ffffffff81071abb>] ? futex_wake+0xd6/0xe7 Dec 10 21:20:29 srv156 kernel: [110625.163010] [<ffffffff8105178a>] ? do_group_exit+0x76/0x9d Dec 10 21:20:29 srv156 kernel: [110625.163016] [<ffffffff8105df9f>] ? get_signal_to_deliver+0x310/0x339 Dec 10 21:20:29 srv156 kernel: [110625.163023] [<ffffffff81010037>] ? do_notify_resume+0x87/0x73f Dec 10 21:20:29 srv156 kernel: [110625.163029] [<ffffffff810cc664>] ? handle_mm_fault+0x7aa/0x80f Dec 10 21:20:29 srv156 kernel: [110625.163036] [<ffffffff81073f14>] ? compat_sys_futex+0x10d/0x12b Dec 10 21:20:29 srv156 kernel: [110625.163043] [<ffffffff812fb546>] ? do_page_fault+0x2e0/0x2fc Dec 10 21:20:29 srv156 kernel: [110625.163049] [<ffffffff81010e0e>] ? int_signal+0x12/0x17 Dec 10 21:20:29 srv156 kernel: [110625.163114] BUG: Bad page state in process java pfn:14fa0c Dec 10 21:20:29 srv156 kernel: [110625.163120] page:ffffea000496b2a0 flags:020000000002001c count:0 mapcount:-1 mapping:ffff88039dc0db30 index:11e3 Dec 10 21:20:29 srv156 kernel: [110625.164563] Pid: 21356, comm: java Tainted: G B 2.6.32-5-amd64 #1 Dec 10 21:20:29 srv156 kernel: [110625.164570] Call Trace: Dec 10 21:20:29 srv156 kernel: [110625.164578] [<ffffffff810b71a9>] ? bad_page+0x116/0x129 Dec 10 21:20:29 srv156 kernel: [110625.164586] [<ffffffff810b7692>] ? free_pages_check+0x38/0x57 Dec 10 21:20:29 srv156 kernel: [110625.164595] [<ffffffff810b89cf>] ? free_hot_cold_page+0x46/0x190 Dec 10 21:20:29 srv156 kernel: [110625.164603] [<ffffffff810b8b82>] ? __pagevec_free+0x69/0x7f Dec 10 21:20:29 srv156 kernel: [110625.164611] [<ffffffff810bba3f>] ? release_pages+0x137/0x18d Dec 10 21:20:29 srv156 kernel: [110625.164620] [<ffffffff810d8559>] ? free_pages_and_swap_cache+0x57/0x73 Dec 10 21:20:29 srv156 kernel: [110625.164629] [<ffffffff810cb5ed>] ? unmap_vmas+0x6ab/0x931 Dec 10 21:20:29 srv156 kernel: [110625.164637] [<ffffffff810cfc74>] ? exit_mmap+0xc4/0x148 Dec 10 21:20:29 srv156 kernel: [110625.164644] [<ffffffff8104bbc1>] ? mmput+0x3c/0xdf Dec 10 21:20:29 srv156 kernel: [110625.164652] [<ffffffff8104f81e>] ? exit_mm+0x102/0x10d Dec 10 21:20:29 srv156 kernel: [110625.164660] [<ffffffff81051243>] ? do_exit+0x1f8/0x6c9 Dec 10 21:20:29 srv156 kernel: [110625.164667] [<ffffffff81071abb>] ? futex_wake+0xd6/0xe7 Dec 10 21:20:29 srv156 kernel: [110625.164675] [<ffffffff8105178a>] ? do_group_exit+0x76/0x9d Dec 10 21:20:29 srv156 kernel: [110625.164683] [<ffffffff8105df9f>] ? get_signal_to_deliver+0x310/0x339 Dec 10 21:20:29 srv156 kernel: [110625.164692] [<ffffffff81010037>] ? do_notify_resume+0x87/0x73f Dec 10 21:20:29 srv156 kernel: [110625.164700] [<ffffffff810cc664>] ? handle_mm_fault+0x7aa/0x80f The last piece of log, has been recently posted, because I've just found it. It seems Java process do something and began to slowly eat all the resources of the server. I don't know exactly if this could be the root cause. Im using Debian Squeeze. uname -a Linux srv156 2.6.32-5-amd64 #1 SMP Sun Sep 23 11:00:33 UTC 2012 x86_64 GNU/Linux I really will appreciate your help, i dont know what more to do.

  Read the article

• How to set up port forwarding and firewall settings for torrents using Transmsission on Mac OSX 10.5

  - by Liz

  I have picked up bits of advice here and there on the internet and got someway through this tortuous exercise (after it took 18 hours to download the first torrent I tried yesterday - magnet-link for a film). Where I have got stuck is with configuring the firewall on the Netgear Router but I am not sure if I have caused the problem myself by something else I have done configuring the Mac System Preferences for Security or Networking. I have been following the sections of these instructions that seem to apply, although they are written for a different OSX version (don't know which one, but the screen shots do not match what I see) and I am not wanting to set up my Mac as a server and attending to the parts that apply to port forwarding for Netgear rather than LinkSys: http://homepage.mac.com/car1son/static_port_fwd_intro.html I have been trying to follow these instructions: Instructions for DG834, DG834G, DG824M, FR114W, FM114P, FR114P, FR328S, FVL328, FVS328, FVS338, FVX538, FWAG114, FWG114P, or FVS318v3 These routers do port forwarding by assigning port numbers to a "service" associated with the application you want to run. "Rules" are set for particular services. Rules block or allow access, based on various conditions such as the time of day and the name of the service. To Create a New Inbound or Outbound Rule 1. Submit the router's address in an Internet browser. (The default is 192.168.0.1). 2. Enter the router's username and password. 3. From the main menu, click Security > Rules. 4. Click Add for inbound or outbound traffic, as appropriate to the application you are planning to run. 5. Select the Service. The services the router knows about are listed in the drop down. If the service you want is not listed, add it as described in the next section. 6. Select the Action, for example ALLOW always. 7. For Send to LAN Server, enter the IP address of the local server. Note that this is also the IP address the computers on your LAN will access. 8. For WAN User choose Any, or limit access to particular IP addresses. 9. For Log selection it is reasonable to turn logs on, especially at the beginning when you are unsure of the result of the changes you are making. Later, you may want to set logs to "Never" for performance reasons. 10. Click Apply. As noted in user manual for some models: * Consider using the Dynamic DNS feature on the Advanced menu, so that external users can find your network when the DHCP lease is renewed by your ISP. * If your own LAN server uses DHCP, and your IPs change on rebooting, consider using the Reserved IP Address feature in the LAN IP menu. To Add a Service for These Routers 1. Click Security > Services > Add Custom Service. 2. Enter any name you choose for the service. 3. Select whether the service is to use TCP or UDP. If you are unsure, select both. 4. Enter the lowest port number used by the service. 5. Enter the highest port number used. If the service uses only one port number, enter the same number. 6. Click Apply. There is no "Security - Rules" submenu in the Netgear page, so I have been trying to access "Security - Firewall Rules". I can access everthing else in the Netgear settings as Admin but I cannot get the "Firewall Rules" section to open up. (I am not 100% sure I will know exactly what to do if and when I do get it opened up!) I haven't managed to find though searching the internet any instructions that would seem to apply specifically to what I am trying to achieve, so would be very grateful if someone could either point me in the right direction or give me some advice directly. Best wishes, Liz

  Read the article

• Remote Desktop Services Gateway Issue

  - by AVandelay05

  Alright fellow techies here's the rundown. I have installed Server 2008 r2 Remote Dekstop Services on a VM in my network. I installed the following RD role services: RD Session Host, Licensing, Connection Broker, Gateway, Web Access. When I set things up originally, the gateway server and RDWeb worked as it should locally. After getting things running locally (remoteserver.domainname.local) I wanted to test things externally. From the outside, I couldn't get things running (meaning I could connect to rdweb access externally, but when I tried to run an app I would get the message "can't connect/find computer"). Here's my setup for external access The VM has every RD Services role services installed on it, meaning it acts as gateway, rd web access, session host, licensing, the whole bit. I made a self-signed certificate on the gateway server (gateway.domainname.net is the cert name). Internally, I have a secondary forward-lookup zone called domainname.net with an A record gateway pointing to the local IP of the gateway server. On our public DNS (domainname.net) I have an A record gateway. This is to access the RDWeb externally. In IIS I have the following authentication settings RDWeb: All disabled except for anonymous authentication Rpc: All disabled except for basic and windows RpcWithCert: All disbled except for windows authentication I have the necessary web access config in our sonicwall tz210 (https and rdp, external ip pointing to local ip of rds server) RAP and CAP have the correct user and computer groups, authentication, and allowed devices After all of this, here's what happens accessing externally. I can login correctly to RDWeb Access (I've tried a bogus login, I can't login to it so that's working properly). I see the Apps for use. I click on an app, click connect, the credential window opens, I put in the correct user creds, it tries to connect to the gateway server, but then the cred window comes back in view. I tried to reach a limit of failed logins, but never reached one, haha. So from the same external client machine I try to connect to the gateway through a Remote Desktop connection. I put in the correct gateway settings in the RD window, try to connect and get the same results as I did in RDWeb access. I checked the event logs on the RD Services machine and saw the following event IDs around the time I tried to login externally: ID 6037 with the message "The program svchost.exe, with the assigned process ID 2168, could not authenticate locally by using the target name host/gateway.domainname.net. The target name used is not valid. A target name should refer to one of the local computer names, for example, the DNS host name. Try a different target name." ID 10 RADWebAccess "RD Web Access was unable to access gateway.domainname.net, which is the server that is specified as running the RemoteApp and Desktop Connection Management service. Ensure that the computer account of the RD Web Access server is a member of the TS Web Access Computers security group on gateway.domainname.net" ID 4625 "An account failed to log on. Subject: Security ID: NULL SID Account Name: - Account Domain: - Logon ID: 0x0 Logon Type: 3 Account For Which Logon Failed: Security ID: NULL SID Account Name: Administrator Account Domain: gateway.domainname.net Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc000006a Process Information: Caller Process ID: 0x0 Caller Process Name: - Network Information: Workstation Name: USER-LAPTOP Source Network Address: External IP Source Port: 63125 Detailed Authentication Information: Logon Process: NtLmSsp Authentication Package: NTLM Transited Services: - Package Name (NTLM only): - Key Length: 0 This event is generated when a logon request fails. It is generated on the computer where access was attempted. The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe. The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network). The Process Information fields indicate which account and process on the system requested the logon. The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases. The authentication information fields provide detailed information about this specific logon request. - Transited services indicate which intermediate services have participated in this logon request. - Package name indicates which sub-protocol was used among the NTLM protocols." I don't think the VM has a null SID. The SID of the VM and it's physical host have different SIDS. I can access the blank page for rpc externally using the external gateway name. It seems like authentication is a problem. Also, is it a problem that the external name of the gateway server doesn't match the local name? The external name (which the cert is based on) is gateway.domainname.net and the internal name is remoteserver.domainname.local. That's the only thing I can think of that would be the problem, but the external name has to be different from the local right? Internally, I ping gateway.domainname.net and it gives me the correct local IP of the server. Now, there isn't an actual computer name in AD, but I don't know how I would achieve that? I hope I've been clear....any help would be appreciated. I think I'm close to achieving this. :)

  Read the article

• Optimize php-fpm and varnish for a powerfull server

  - by Jim

  My setup is: Intel® Core™ i7-2600 and RAM 16 GB DDR3 RAM varnish+nginx+php-fpm+apc for a not very heavy WordPress blog with W3 Total Cache and CDN My problem is that after 55 hits per second according to blitz.io varnish starts giving out timeouts. CPU usage at this time is hardly 1%. Free memory at all time remains 10GB+. I tried benchmarking php-fpm directly with result of 150hits/s without any timeouts. But after that the CPU usage goes 100% and it stops responding. Can you help me optimize it to handle more? As i understand nginx has nothing to do over here so i dont put its config. php-fpm config listen = /tmp/php5-fpm.sock listen.allowed_clients = 127.0.0.1 user = nginx group = nginx pm = dynamic pm.max_children = 150 pm.start_servers = 7 pm.min_spare_servers = 2 pm.max_spare_servers = 15 pm.max_requests = 500 slowlog = /var/log/php-fpm/www-slow.log php_admin_value[error_log] = /var/log/php-fpm/www-error.log php_admin_flag[log_errors] = on apc extension = apc.so apc.enabled=1 apc.shm_size=512MB apc.num_files_hint=0 apc.user_entries_hint=0 apc.ttl=7200 apc.use_request_time=1 apc.user_ttl=7200 apc.gc_ttl=3600 apc.cache_by_default=1 apc.filters apc.mmap_file_mask=/tmp/apc.XXXXXX apc.file_update_protection=2 apc.enable_cli=0 apc.max_file_size=1M apc.stat=1 apc.stat_ctime=0 apc.canonicalize=0 apc.write_lock=1 apc.report_autofilter=0 apc.rfc1867=0 apc.rfc1867_prefix =upload_ apc.rfc1867_name=APC_UPLOAD_PROGRESS apc.rfc1867_freq=0 apc.rfc1867_ttl=3600 apc.include_once_override=0 apc.lazy_classes=0 apc.lazy_functions=0 apc.coredump_unmap=0 apc.file_md5=0 apc.preload_path Varnish VCL backend default { .host = "127.0.0.1"; .port = "8080"; .connect_timeout = 6s; .first_byte_timeout = 6s; .between_bytes_timeout = 60s; } acl purgehosts { "localhost"; "127.0.0.1"; } # Called after a document has been successfully retrieved from the backend. sub vcl_fetch { # Uncomment to make the default cache "time to live" is 5 minutes, handy # but it may cache stale pages unless purged. (TODO) # By default Varnish will use the headers sent to it by Apache (the backend server) # to figure out the correct TTL. # WP Super Cache sends a TTL of 3 seconds, set in wp-content/cache/.htaccess set beresp.ttl = 24h; # Strip cookies for static files and set a long cache expiry time. if (req.url ~ "\.(jpg|jpeg|gif|png|ico|css|zip|tgz|gz|rar|bz2|pdf|txt|tar|wav|bmp|rtf|js|flv|swf|html|htm)$") { unset beresp.http.set-cookie; set beresp.ttl = 24h; } # If WordPress cookies found then page is not cacheable if (req.http.Cookie ~"(wp-postpass|wordpress_logged_in|comment_author_)") { # set beresp.cacheable = false;#versions less than 3 #beresp.ttl>0 is cacheable so 0 will not be cached set beresp.ttl = 0s; } else { #set beresp.cacheable = true; set beresp.ttl=24h;#cache for 24hrs } # Varnish determined the object was not cacheable #if ttl is not > 0 seconds then it is cachebale if (!beresp.ttl > 0s) { # set beresp.http.X-Cacheable = "NO:Not Cacheable"; } else if ( req.http.Cookie ~"(wp-postpass|wordpress_logged_in|comment_author_)" ) { # You don't wish to cache content for logged in users set beresp.http.X-Cacheable = "NO:Got Session"; return(hit_for_pass); #previously just pass but changed in v3+ } else if ( beresp.http.Cache-Control ~ "private") { # You are respecting the Cache-Control=private header from the backend set beresp.http.X-Cacheable = "NO:Cache-Control=private"; return(hit_for_pass); } else if ( beresp.ttl < 1s ) { # You are extending the lifetime of the object artificially set beresp.ttl = 300s; set beresp.grace = 300s; set beresp.http.X-Cacheable = "YES:Forced"; } else { # Varnish determined the object was cacheable set beresp.http.X-Cacheable = "YES"; if (beresp.status == 404 || beresp.status >= 500) { set beresp.ttl = 0s; } # Deliver the content return(deliver); } sub vcl_hash { # Each cached page has to be identified by a key that unlocks it. # Add the browser cookie only if a WordPress cookie found. if ( req.http.Cookie ~"(wp-postpass|wordpress_logged_in|comment_author_)" ) { #set req.hash += req.http.Cookie; hash_data(req.http.Cookie); } } # vcl_recv is called whenever a request is received sub vcl_recv { # remove ?ver=xxxxx strings from urls so css and js files are cached. # Watch out when upgrading WordPress, need to restart Varnish or flush cache. set req.url = regsub(req.url, "\?ver=.*$", ""); # Remove "replytocom" from requests to make caching better. set req.url = regsub(req.url, "\?replytocom=.*$", ""); remove req.http.X-Forwarded-For; set req.http.X-Forwarded-For = client.ip; # Exclude this site because it breaks if cached if ( req.http.host == "sr.ituts.gr" ) { return( pass ); } # Serve objects up to 2 minutes past their expiry if the backend is slow to respond. set req.grace = 120s; # Strip cookies for static files: if (req.url ~ "\.(jpg|jpeg|gif|png|ico|css|zip|tgz|gz|rar|bz2|pdf|txt|tar|wav|bmp|rtf|js|flv|swf|html|htm)$") { unset req.http.Cookie; return(lookup); } # Remove has_js and Google Analytics __* cookies. set req.http.Cookie = regsuball(req.http.Cookie, "(^|;\s*)(__[a-z]+|has_js)=[^;]*", ""); # Remove a ";" prefix, if present. set req.http.Cookie = regsub(req.http.Cookie, "^;\s*", ""); # Remove empty cookies. if (req.http.Cookie ~ "^\s*$") { unset req.http.Cookie; } if (req.request == "PURGE") { if (!client.ip ~ purgehosts) { error 405 "Not allowed."; } #previous version ban() was purge() ban("req.url ~ " + req.url + " && req.http.host == " + req.http.host); error 200 "Purged."; } # Pass anything other than GET and HEAD directly. if (req.request != "GET" && req.request != "HEAD") { return( pass ); } /* We only deal with GET and HEAD by default */ # remove cookies for comments cookie to make caching better. set req.http.cookie = regsub(req.http.cookie, "1231111111111111122222222333333=[^;]+(; )?", ""); # never cache the admin pages, or the server-status page, or your feed? you may want to..i don't if (req.request == "GET" && (req.url ~ "(wp-admin|bb-admin|server-status|feed)")) { return(pipe); } # don't cache authenticated sessions if (req.http.Cookie && req.http.Cookie ~ "(wordpress_|PHPSESSID)") { return(lookup); } # don't cache ajax requests if(req.http.X-Requested-With == "XMLHttpRequest" || req.url ~ "nocache" || req.url ~ "(control.php|wp-comments-post.php|wp-login.php|bb-login.php|bb-reset-password.php|register.php)") { return (pass); } return( lookup ); } Varnish Daemon options DAEMON_OPTS="-a :80 \ -T 127.0.0.1:6082 \ -f /etc/varnish/ituts.vcl \ -u varnish -g varnish \ -S /etc/varnish/secret \ -p thread_pool_add_delay=2 \ -p thread_pools=8 \ -p thread_pool_min=100 \ -p thread_pool_max=1000 \ -p session_linger=50 \ -p session_max=150000 \ -p sess_workspace=262144 \ -s malloc,5G" Im not sure where to start, should i for start optimize php-fpm and then go to varnish or php-fpm is at its max right now so i should start looking for the problem in varnish?

  Read the article

• How to set up linux watchdog daemon with Intel 6300esb

  - by ACiD GRiM

  I've been searching for this on Google for sometime now and I have yet to find proper documentation on how to connect the kernel driver for my 6300esb watchdog timer to /dev/watchdog and ensure that watchdog daemon is keeping it alive. I am using RHEL compatible Scientific Linux 6.3 in a KVM virtual machine by the way Below is everything I've tried so far: dmesg|grep 6300 i6300ESB timer: Intel 6300ESB WatchDog Timer Driver v0.04 i6300ESB timer: initialized (0xffffc900008b8000). heartbeat=30 sec (nowayout=0) | ll /dev/watchdog crw-rw----. 1 root root 10, 130 Sep 22 22:25 /dev/watchdog | /etc/watchdog.conf #ping = 172.31.14.1 #ping = 172.26.1.255 #interface = eth0 file = /var/log/messages #change = 1407 # Uncomment to enable test. Setting one of these values to '0' disables it. # These values will hopefully never reboot your machine during normal use # (if your machine is really hung, the loadavg will go much higher than 25) max-load-1 = 24 max-load-5 = 18 max-load-15 = 12 # Note that this is the number of pages! # To get the real size, check how large the pagesize is on your machine. #min-memory = 1 #repair-binary = /usr/sbin/repair #test-binary = #test-timeout = watchdog-device = /dev/watchdog # Defaults compiled into the binary #temperature-device = #max-temperature = 120 # Defaults compiled into the binary #admin = root interval = 10 #logtick = 1 # This greatly decreases the chance that watchdog won't be scheduled before # your machine is really loaded realtime = yes priority = 1 # Check if syslogd is still running by enabling the following line #pidfile = /var/run/syslogd.pid Now maybe I'm not testing it correctly, but I would expecting that stopping the watchdog service would cause the /dev/watchdog to time out after 30 seconds and I should see the host reboot, however this does not happen. Also, here is my config for the KVM vm <!-- WARNING: THIS IS AN AUTO-GENERATED FILE. CHANGES TO IT ARE LIKELY TO BE OVERWRITTEN AND LOST. Changes to this xml configuration should be made using: virsh edit sl6template or other application using the libvirt API. --> <domain type='kvm'> <name>sl6template</name> <uuid>960d0ac2-2e6a-5efa-87a3-6bb779e15b6a</uuid> <memory unit='KiB'>262144</memory> <currentMemory unit='KiB'>262144</currentMemory> <vcpu placement='static'>1</vcpu> <os> <type arch='x86_64' machine='rhel6.3.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <cpu mode='custom' match='exact'> <model fallback='allow'>Westmere</model> <vendor>Intel</vendor> <feature policy='require' name='tm2'/> <feature policy='require' name='est'/> <feature policy='require' name='vmx'/> <feature policy='require' name='ds'/> <feature policy='require' name='smx'/> <feature policy='require' name='ss'/> <feature policy='require' name='vme'/> <feature policy='require' name='dtes64'/> <feature policy='require' name='rdtscp'/> <feature policy='require' name='ht'/> <feature policy='require' name='dca'/> <feature policy='require' name='pbe'/> <feature policy='require' name='tm'/> <feature policy='require' name='pdcm'/> <feature policy='require' name='pdpe1gb'/> <feature policy='require' name='ds_cpl'/> <feature policy='require' name='pclmuldq'/> <feature policy='require' name='xtpr'/> <feature policy='require' name='acpi'/> <feature policy='require' name='monitor'/> <feature policy='require' name='aes'/> </cpu> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/mnt/data/vms/sl6template.img'/> <target dev='vda' bus='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </disk> <controller type='usb' index='0'> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x2'/> </controller> <interface type='bridge'> <mac address='52:54:00:44:57:f6'/> <source bridge='br0.2'/> <model type='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <interface type='bridge'> <mac address='52:54:00:88:0f:42'/> <source bridge='br1'/> <model type='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target type='serial' port='0'/> </console> <watchdog model='i6300esb' action='reset'> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0'/> </watchdog> <memballoon model='virtio'> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> </domain> Any help is appreciated as the most I've found are patches to kvm and general softdog documentation or IPMI watchdog answers.

  Read the article

< Previous Page | 531 532 533 534 535 536 537 538 539 540 541 542  | Next Page >