Search Results

Search found 17569 results on 703 pages for 'computer intelligence'.

Page 536/703 | < Previous Page | 532 533 534 535 536 537 538 539 540 541 542 543  | Next Page >

• Configuring an Engenius 3500

  - by dsiddens

  The title speaks to only half of the issue: the other half are the settings in Ubuntu and the sequences therein. The computer in this issue does receive internet with the external antenna jack at the back being fed with a simple magnetic base antenna designed for putting on the roof of an automobile. However, that signal is weak and the Engenius with an external antenna (Rootenna ~15db gain) and ehternet wire will supply a stronger, faster signal. I've set the Engenius to the desired source and entered the correct WEP password. The lights on the Engenius indicate that it's connected to the access point. At the Ubuntu side of this I've worked to no avail changing settings with "Edit Connections" to the point I'm Ask(ing)Ubuntu for help. I have and have RTFM for Engenius 3500 There is an embarrassing side note to this issue: At one time I had the Engenius working! It seems that I can't recall the settings and sequences I used way back when. And I may as well confess to not knowing the Command Line. I'm a GUI guy. Thank you for your time, Doug

  Read the article

• Why do VMs need to be "stack machines" or "register machines" etc.?

  - by Prog

  (This is an extremely newbie-ish question). I've been studying a little about Virtual Machines. Turns out a lot of them are designed very similarly to physical or theoretical computers. I read that the JVM for example, is a 'stack machine'. What that means (and correct me if I'm wrong) is that it stores all of it's 'temporary memory' on a stack, and makes operations on this stack for all of it's opcodes. For example, the source code 2 + 3 will be translated to bytecode similar to: push 2 push 3 add My question is this: JVMs are probably written using C/C++ and such. If so, why doesn't the JVM execute the following C code: 2 + 3..? I mean, why does it need a stack, or in other VMs 'registers' - like in a physical computer? The underlying physical CPU takes care of all of this. Why don't VM writers simply execute the interpreted bytecode with 'usual' instructions in the language the VM is programmed with? Why do VMs need to emulate hardware, when the actual hardware already does this for us? Again, very newbie-ish questions. Thanks for your help

  Read the article

• Is it possible to host a web server from behind a NAT

  - by iamrohitbanga

  My PC is behind a NAT router that has a public IP address. If I want to host a website then I believe I need a domain name which I can purchase from some site which would pledge to resolve all DNS requests for that domain name and send the IP address of my NAT router (assuming I do not want to host my domain name on their servers). Now I want to host a web server on my computer. What changes should be done to the NAT router's configuration to forward all HTTP requests for example.com to my PC in the internal network. Is the above strategy correct? Is it commonly used?

  Read the article

• X58 RAID 10 - Am I forced to use Sata2?

  - by Avi

  I'm building a new dev computer. It will be running a few VMWare Worksation virtual machines. I was advised on Serverfault to use Raid10 for performance. Raid 10 uses 4 disks. I contacted my supplier who suggested a gigabyte X58A motherboard and 4 Western Digital Caviar black 6Gb/s disks. I have checked the spec for the X58A board, however, and it says: SATA 3Gb/s: RAID 0, RAID 1, RAID 5, and RAID 10 SATA 6Gb/s: RAID 0, and RAID 1. I'm losing half the bandwidth because I'm forced to use SATA2! What should I do?

  Read the article

• How do I set up two existing disks with identical contents as a single mirrored volume in Windows 7 without losing data?

  - by Software Monkey

  I have two data disks that were, heretofore, in a mobo RAID configuration in Windows 7. They are now separate AHCI disks, visible in Computer Management. How to I go about making them a single mirrored volume in Windows? Note: The data is backed up up on two other separate disks, but it's a fair amount of work to do a restore (over 120'000 files, and I have to reset permissions). Note2: Currently the two disks are identical, and I can use the content of either one for this.

  Read the article

• DVI problem with LG L204WT

  - by Holgerwa

  I have a LG L204WT which has VGA and DVI connectors. Until recently, I have used the monitor via VGA, but now I have upgraded the graphics board and switched to DVI. The problem is that each time after the computer starts, the monitor either doesn't show anything (black screen, but doesn't go into standby) or the picture is distorted. I then switch the monitor off and on several times, and at some point it starts correctly and then I can work as usual. This only happens on startup. It is one out of 3 monitors, the other two work fine. It seems to me as if the monitor is not able to synchronize on the DVI signal and either shows a distorted picture or nothing at all. There are no settings in the monitor setup that would change anything. What could be the problem?

  Read the article

• Does installing windows format the hard disk?

  - by Jason

  My Google search for ""does installing windows format the hard disk" returns: No results found for "does installing windows format the hard disk". I was quite surprised. I'm hoping to get a quick answer here. Does an install format the hard disk, and destroy all data, including non-os/s data? -Or do you specifically have to say "format" at some point so you know you are losing everything? [I tried to go to SP3, but it doesn't work on my computer. My SP2 disk is fired. I only have a SP1 disk, with a seperate SP2 package. I can't get to Safe Mode to uninstall SP3 ("Windows XP Setup cann run under Safemode. Setup will restart now.). I don't want running the SP1 disk to destroy any non-o/s data.] Thanks.

  Read the article

• Powershell window preventing shutdown

  - by FrinkTheBrave

  If I have a PowerShell window (at the PS command prompt) on display it prevents the computer shutting down. i.e. if I open a powershell window and then try to shutdown the server, I get the End Program popup saying Windows cannot end this program I get the same result if I start the powershell from the start menu, from a cmd prompt and from a shortcut with -NoExit specified. Any ideas how I can get shutdown to automatically close a powershell window (if it is at the PS prompt) in the same way as it would for a CMD window? Alternatively, is it possible for PowerShell to detect when a shutdown has been initiated and therefore close itself?

  Read the article

• Ubuntu 11.04 64bits Keeps Randomly Freezing

  - by user971602

  This has been a real headache for me since the number of freezes has increase from twice a week to about 1 or twice a day. The system just halts and nothing can be done but hitting the restart button. At the beginning I thought it was related to Flash since I was getting random freezes when playing full screen flash videos online. I also thought it could be the wireless pci card. But the system has freezed using browsing around GNOME. The truth is, the freezes are really random and strange. I checked this thread Ubuntu keeps randomly freezing and try to ssh my computer using another one, but I could not ssh since it was really totally frozen. NumLock or CapsLock wasn't responding or blinking. Since I could not ssh I, also ignored this article https://wiki.ubuntu.com/X/Troubleshooting/Freeze According to my wife, the system has also halted under Win7 Pro 64bit but with less frequency. Here is my system configuration Intel Core i7 2600k ASRock Z68 Extreme3 gen3 Motherboard Crucial M4 128GB CT128M4SSD2 SSD WD Caviar Green WD10EADS 1TB SATA II G.SKILL Ripjaws X Series 8GB (2 x 4GB) DDR2 OCZ ModXStream 600W Power Supply Rosewill RNX-N300X PCI Wireless Adapter No external Graphics Card I remove the Wireless card and used Ethernet to see if the problem was the that, but I got a freeze after doing that. I also ran memtest86 and everything was ok. The only other thing I might suspect of is the SSD. I will try to clone the SSD to a HDD to see if that solve the problem. At this point I am stuck with the freezes. Do anyone have a clue of why this is happening and how can i solve this?

  Read the article

• Dual displays not working - NVidia - Ubuntu 12.4

  - by user75105

  Graphics Card: NVidia 460 GTX. Driver: NVIDIA accelerated graphics driver (version current) I have one DVI monitor, an old Dell LCD from 2005, and one VGA monitor, an Asus ML238H from 2010 whose HDMI port broke. The Asus is plugged into my graphics card's primary monitor slot and is the better monitor even though it is VGA but my computer defaults to the Dell. This happens when I boot as well; the loading screens, the motherboard brand image, etc. are all displayed on the Dell monitor until Windows loads. Then both monitors work. The same thing happened when I booted up Ubuntu 12.4 but I did not see the second monitor when the log-in screen popped up, nor did I when I logged in. I went to System Settings/Displays and my Asus monitor is not an option. I clicked Detect Displays and the Asus is not detected. I looked at the other questions regarding NVIDIA drivers and recalled my problems with Ubuntu a few years ago and decided to check the driver. I went to Additional Drivers to install the proprietary driver and it looks like it's installed and active but I'm still having this problem. There is another driver option, the post-release NVIDIA driver, but that does not fix the problem either. Also, under System Details/Graphics the graphics device is listed as Unknown, which might indicate that it is using an open source generic driver and not the proprietary NVidia driver. But under Additional Drivers it says that I am using the NVidia driver. Any help is appreciated.

  Read the article

• View changelog of all packages to be upgraded before upgrading

  - by Stein G. Strindhaug

  When using synaptic on my Ubuntu desktop computer i can review all changelog of all the packages to be upgraded, and unselect a package for upgrade if I want. On my desktop I usually install everything, but I like to at least review what the changes are so that I can delay the upgrade if I suspect it could cause problems with the development tools I use. On a server (Ubuntu Server) with no x-server how can I do the same thing on the console: list all packages that will be updated (apt-get --dry-run upgrade does this along with a lot of noisy simulated install messages), view the changelog (if any) from last upgrade to the version it will be upgraded to. select which packages I want to ignore, or which I want to upgrade I've searched a lot for this but I haven't found anything, possibly I'm not using the correct terminology; but surely this must be possible. Synaptic must get it's info from some some low-level tool I assume? Complicated shellscripts are welcome too, if this is not already easily done with the existing tools.

  Read the article

• Black screen with cursor after BIOS screen

  - by Radio

  Here is a weird one, Got computer with Windows XP. It's getting stuck on a black screen with cursor blinking. What did I do: - Boot from installation CD (recovery option - command line): chkdsk C: /R copy D:\i386\ntdetect.com c:\ copy D:\i386\ntldr c:\ fixmbr fixboot Chkdsk showed 0 bad sectors and no problems during scan. dir on C:\ shows all directories and files in place (Windows, Program Files, Documents and Settings). BIOS shows correct boot drive. Still does not boot. Not sure what to think of. Please help. UPDATE: Just performed these steps: Backed up current disk C: (without MBR) using True Image to external hard drive Ran Windows XP clean installation with deleting all partitions and creating new one. Hard drive booted fine into Windows GUI installation!!! Then: I interrupted installation. Booted from True Image recovery CD and restored archive of disk C to an new partition. Same issue with black screen.

  Read the article

• Software to create a virtual parallel port in Windows XP?

  - by drknexus

  I am writing a program that will eventually be used on a computer with a physical parallel port and will need to set certain pins high or low in order to signal to an external device. However, the development laptop I am using does not have any physical parallel ports and is too low powered to run a virtual machine. Is there any option available that will create a virtual parallel port within Windows XP? Ideally it would include a debug mode that would allow me to see what values have been pushed out on the parallel port.

  Read the article

• Lan DNS not working after reinstall of Ubuntu 13.10

  - by DrorCohen

  I upgrade my Ubuntu desktop to 13.10. When I say upgrade I mean installed on a new partition from scratch (old partition is available if To the problem: I'm trying to ping a host (Drobo-FS server) by it's host name. I get "Unknown Host". However pinging from another computer on the same lan - works fine (a laptop with 12.04 lts). for that matter every ping from the 13.10 to the local lan by hostname fails, ping with ip works. I don't have a local DNS server but somehow all the other computers in the network find each other by host name - only this new one fails... help appreciated...

  Read the article

• Access to local network machine

  - by Jirka Kopriva

  I have granted new setting from my domain provider. Domain with specific port is pointing on computer in local network (fixed ip) like: mydomain.com:87 -> 192.168.1.1 Local machine is running on win server 2008. Everything works fine on local network. But mydomain.com:87 is not working. Are there extra settings for win server to allow connection from outside? (Firewall is turned off while searching for working result.)

  Read the article

• What to do about "system running in low-graphics mode"?

  - by ubuntubabe

  My Dell which was 5 years old suddenly karked it and I had the "low graphics" black screen and useless dialogue box. As I believed it was a dead graphics card I went out and bought a brand new machine. I put aside the new machine and tried again in vain to open the Dell. I eventually got to the command line via Ctrl+Alt+F1. I logged into my account from there, and simply started a series of sudo apt-get remove of various softwares that I knew were installed on my PC (software without any great consequence like Google earth, tweak, Skype etc). Lo and behold after a sudo reboot my computer was fine again! So now I have 2 computers. BUT one week after buying the other one and installing 12.04 because I love Ubuntu, the SAME PROBLEM arrived! I once again deleted Google earth, Skype, and did a sudo reboot and everything worked as before. I think there is a bug or something in 12.04 as this problem has never arisen with any other versions of Ubuntu.

  Read the article

• Windows 7 - saved wifi access points disappear from list

  - by KáGé

  I'm having a weird issue with Windows 7 x64: I'm moving my notebook between two locations weekly, at each I have a wifi router. They both have hidden SSID-s, which are different. If I save one, the other one gets deleted from the list, as if overwritten, so I always have to retype the SSID and password, if I want to connect after moving my computer. At first I tought the problem was caused by both routers having the same password, but after I changed one (suffixed it with "_2") it persisted. What can I do about this? Thanks.

  Read the article

• Network card dies when trying to wake up laptop from sleep

  - by Bugmaster

  I have a Dell XPS 1640 laptop (aka Dell Studio XPS 16), running Vista. Whenever the laptop wakes up from sleep, my Broadcomm LAN card immediately dies. Any attempt to access it completely locks up whichever program I use to access it. There appears to be no way to re-awaken the card, other than rebooting; note that Vista does not even shut down properly if some program is waiting for the card. So far, I have tried the following: Disabled the "allow your computer to shut down this device to save power" in the device properties. This had no effect. Attempted to disable and then enable the card in the device properties. No effect. Tried ipconfig /renew: this locks up ipconfig to the point where I can't even kill its process. Force-install updated drivers from broadcomm: no effect. Does anyone have any other ideas ?

  Read the article

• Shares not working on boot need to reinstall "File and Printer Sharing for Microsoft Networks" on server every morning to fix

  - by Neaox

  I had a problem a few days ago see question here: Can no longer access computer or network shares to my server from any other computers on the network The fix that I found does in fact work however when I boot my PC in the morning the shares are no longer working, to fix this I need to remote desktop into the server and re-install "File and Printer Sharing for Microsoft Networks" on the main adaptor. Doing this makes the shares work again, however it is anoying to have to do this each and every morning. On top of this my offline files are no longer available offline: I store my user profile on the server and had them selected to be "Always Available" however since this has happened they are no longer available offline and the option to make them available offline from the context menu is no longer available. Another problem, and I don't know if this is the cause or just a tell of a deeper issue but this server runs hyper-v, since these problems I can no longer remote desktop into the hyper-v client. Thanks for any help anyone can give.

  Read the article

• Windows 7, how to get unlock (Press Ctrl+Alt+del) prompt on all monitors?

  - by Zugwalt

  I have a laptop that I keep shut in a docking station as I have two screens connected to the laptop and it cannot display to both of those AND its own screen. However, when my computer locks by itself (Not when I lock it using Ctrl+Alt+Del) the login prompt is ONLY on it screen (at least its there when I open it up) and my primary external monitor is off and my other one is all black. This means to log in I have to hit Ctrl+Alt+Del and blindly enter my password--which I don't mind too much, but would prefer if I could actually see the unlock/login prompt instead of typing on a black screen. Any way to have it show the login prompt on all monitors?

  Read the article

• Can't access server from external IP

  - by Mathias

  I have a problem with my web server; I can't access it from the external IP address. I'm using an IIS 7 server, but I've tried with apache on Linux as well. I have forwarded all traffic on port 80 to my computer, but it just won't work. I've done port forwarding with my Minecraft server, and it did work, but when I try it with a web server, no. I've been looking on many many forums, but their methods don't work for me. My router is a Speedport W 723V, if anyone knows that one. Any help is appreciated.

  Read the article

• Cannot access to any windows share including localhost

  - by user21936

  I can't access any share from my operating system, including \\localhost and \\127.0.0.1. I have Windows 7. NetBIOS over IP is enabled, other computers in the network can access my shares and other computer's shares, but my operating system cannot access any share. I have installed Windows XP within VMware, and the virtual windows xp can access all shares including the host shares. I can communicate in other ways like TCP, HTTP and gaming, but not access shares. How to solve this problem?

  Read the article

• Dual displays not working - NVidia - Ubuntu 12.04 - Second Monitor - Two Screens

  - by user75105

  Graphics Card: NVidia 460 GTX. Driver: NVIDIA accelerated graphics driver (version current) I have one DVI monitor, an old Dell LCD from 2005, and one VGA monitor, an Asus ML238H from 2010 whose HDMI port broke. The Asus is plugged into my graphics card's primary monitor slot and is the better monitor even though it is VGA but my computer defaults to the Dell. This happens when I boot as well; the loading screens, the motherboard brand image, etc. are all displayed on the Dell monitor until Windows loads. Then both monitors work. The same thing happened when I booted up Ubuntu 12.04 but I did not see the second monitor when the log-in screen popped up, nor did I when I logged in. I went to System Settings/Displays and my Asus monitor is not an option. I clicked Detect Displays and the Asus is not detected. I looked at the other questions regarding NVIDIA drivers and recalled my problems with Ubuntu a few years ago and decided to check the driver. I went to Additional Drivers to install the proprietary driver and it looks like it's installed and active but I'm still having this problem. There is another driver option, the post-release NVIDIA driver, but that does not fix the problem either. Also, under System Details/Graphics the graphics device is listed as Unknown, which might indicate that it is using an open source generic driver and not the proprietary NVidia driver. But under Additional Drivers it says that I am using the NVidia driver. Any help is appreciated.

  Read the article

• Compaq Presario Laptop Monitor Problems

  - by Nishant

  I am attaching a few pics of my laptop monitor now . Can you please tell me if this is a hardware error which can be rectified by replacing the monitor ? How this happened - I accidently hit my leg on the laptop and jammed it against the wall and ever since the monitor is like this .I plan to replace the Monitor by buying a spare parts laptop that sells in ebay . I wonder if this is a LCD HARDWARE problem or problem with the cable that goes to the monitor . THE OS works fine in the computer .I hope my question is clear . http://img163.imageshack.us/gal.php?g=good1z.jpg

  Read the article

• Windows 7 unreasonable ram usage

  - by Deus Deceit

  I have a fresh install of windows 7, and my ram in normal startup goes up to 2.5 GB. I looked at task manager, and there's at least 1.5 GB missing from there and in resource monitor as well. No indication of what's using that ram. Can someone tell me how I can find out what's consuming my memory? I believe it's a virus but none of the free antivirus programs tracked it down. EDIT I added the pictures bellow. If this is normal usage of windows 7 as some answers imply... then I don't get this at all. P.S My windows 8 Installation was running bellow 2.5 gb actually it was 1. something, until recently that I transferred some files from another computer which had the same problem that mine has now. I deleted windows 8 and installed 7, since i would do that anyway. And now I'm getting high memory usage in windows 7 as well.

  Read the article

< Previous Page | 532 533 534 535 536 537 538 539 540 541 542 543  | Next Page >