Search Results

Search found 19350 results on 774 pages for 'address book'.

Page 537/774 | < Previous Page | 533 534 535 536 537 538 539 540 541 542 543 544  | Next Page >

• How to set up Aptana Studio 3 with a Bitbucket private repo

  - by Titus

  I have just started playing around with Git and would like to push a personal project to a newly created, private repo on Bitbucket using Aptana Studio 3. I tried to use the Git integration in Aptana but I couldn't figure out where to enter my username and password for Bitbucket anywhere. I tried using the Team > Share Project context menu but that keeps throwing the following message: Warning: Permanently added the RSA host key for IP address '207.223.240.181' to the list of known hosts. Permission denied (publickey). fatal: The remote end hung up unexpectedly I'm pretty sure that's because my repo is private. However, I couldn't find a provision to provide any form of credentials for linking to a private repo. Any ideas?

  Read the article

• Sendmail /etc/hosts and DNS ... what is the correct way?

  - by ben

  I found one tutorial on setting up sendmail that says that in the /etc/hosts file, "The entry for 127.0.0.1 must always be followed by the fully qualified domain name (FQDN) of the server." Like so: 127.0.0.1 bigboy.my-site.com localhost.localdomain localhost bigboy (This tutorial is here). However, I can't find anyone else suggesting something like that. instead most people seem to put some combination of localhost and localdomain.localhost after 127.0.0.1, and then some variant of the fully qualified domain name after the public ip address. What is the correct way?

  Read the article

• DVD ROM not working only in windows?

  - by Behrooz A

  I have an Asus N53SV laptop, My DVD rom doesn't read any type of DVD in windows , but I just installed windows 7 from a bootable DVD , I think this problem occurred after I tried to change my partitioning with paragon partition magic , I was trying to shrink , join and so , after that my windows showed an error that windows cannot find [weird address] on hard disk every time on starts. windows itself says the DVD drive works correctly and driver is working properly, but no DVD or CD can be read , note that the DVD I'm trying to read is the same DVD which I used to install windows some minutes ago. I don't know what's the problem

  Read the article

• Setting up wifi router as a switch for Internet Connection Sharing

  - by William C

  Can my laptop with a 3G connection share its Internet via a Wifi router (Dlink DIR-615)? I turned Internet Connection Sharing on and Windows assigned 192.168.137.1 to my laptop's LAN adapter. Do I connect my laptop to the WAN port or to the LAN port of the router? What should I set as my router's IP address? Do I turn DHCP on my router on? Do I assign 192.168.137.x as static addresses on the other computers? If not, what? Is there anything else I need to set on my router? Thank you!

  Read the article

• Setting up Debian squirrelmail

  - by Muazam

  I'm new to networking. I need to set up a email server and I also need to create an email address. ex. [email protected] I've installed squirrelmail and dovecot. http://www.mydomain.com/squirrelmail/src/login.php Shows a log in screen, but when I try to log in I get this error: Error connecting to IMAP server: 127.0.0.1. 111 : Connection refused I have no experience with squirrelmail and dovecote. Anyone can help me out, I really appreciate it. Thanks!

  Read the article

• Amazon EC2 - Unable to connect to MySQL

  - by alexus

  I'm having issue connecting from one VM to another # nmap -p3306 ip-XX-XX-XX-XX.ec2.internal Starting Nmap 6.40 ( http://nmap.org ) at 2014-06-10 17:50 EDT Nmap scan report for ip-XX-XX-XX-XX.ec2.internal (XX.XX.XX.XX) Host is up (0.000033s latency). PORT STATE SERVICE 3306/tcp closed mysql Nmap done: 1 IP address (1 host up) scanned in 1.05 seconds # in my Security Group I allowed Inbound connectivity via port TCP, portrange 3306 and Source 0.0.0.0/0, so theoratically it should work, but in reality it doesn't( I'm running red hat enterprise linux 7 on both VMs. mariadb.service running fine on another VM and I am able to connect to it locally. DB's: # netstat -anp | grep 3306 tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 2324/mysqld # iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # Any ideas what else I missed?

  Read the article

• Removing occurrences of characters in a string

  - by DmainEvent

  I am reading this book, programming Interviews exposed by John Wiley and sons and in chapter 6 they are discussing removing all instances of characters in a src string using a removal string... so removeChars(string str, string remove) In there writeup they sey the steps to accomplish this are to have a boolean lookup array with all values initially set to false, then loop through each character in remove setting the corresponding value in the lookup array to true (note: this could also be a hash if the possible character set where huge like Unicode-16 or something like that or if str and remove are both relatively small... < 100 characters I suppose). You then iterate through the str with a source and destination index, copying each character only if its corresponding value in the lookup array is false... Which makes sense... I don't understand the code that they use however... They have for(src = 0; src < len; ++src){ flags[r[src]] == true; } which is turning the flag value at the remove string indexed at src to true... so if you start out with PLEASE HELP as your str and LEA as your remove you will be setting in your flag table at 0,1,2... t|t|t but after that you will get an out of bounds exception because r doesn't have have anything greater than 2 in it... even using there example you get an out of bounds exception... Am is there code example unworkable? Entire function string removeChars( string str, string remove ){ char[] s = str.toCharArray(); char[] r = remove.toCharArray(); bool[] flags = new bool[128]; // assumes ASCII! int len = s.Length; int src, dst; // Set flags for characters to be removed for( src = 0; src < len; ++src ){ flags[r[src]] = true; } src = 0; dst = 0; // Now loop through all the characters, // copying only if they aren’t flagged while( src < len ){ if( !flags[ (int)s[src] ] ){ s[dst++] = s[src]; } ++src; } return new string( s, 0, dst ); } as you can see, r comes from the remove string. So in my example the remove string has only a size of 3 while my str string has a size of 11. len is equal to the length of the str string. So it would be 11. How can I loop through the r string since it is only size 3? I haven't compiled the code so I can loop through it, but just looking at it I know it won't work. I am thinking they wanted to loop through the r string... in other words they got the length of the wrong string here.

  Read the article

• Electronic Postage provider compatible with Microsoft Word Mail Merge

  - by theguy

  We're looking for an e-postage provider that is capable of working with the Mail Merge function in Microsoft Word 2007. Every now and then we extract addresses from our database to mail letters or notices. We use Mail Merge in Word 2007 to print the address information straight to the envelopes and then run all the envelopes through a Pitney Bowes Postage Meter. It would save us a huge step if we could somehow get an e-postage provider where we can just print out the postage straight to the envelopes along with the addresses at the same time. Anyone know of such a provider or a better solution?

  Read the article

• Weird (?) issue with Exchange Forwarding

  - by abszero

  Hello everyone. Here is the long and short of it: the company I work for was purchased by another company who uses Gmail for domains as their email provider. We use an in house Exchange box. No big deal, I dropped into Active Directoy and created several Contact objects that represented our new email addresses at Gmail. I then went through each employees record and have their mail set to forward to this new address and not deliver locally. So I am forwarding email for me@domain1 to me@domain2 and this works great as long as I don't send an email from me@domain2 to me@domain1. If I log into my personal Gmail account and send an email to me@domain1 the email is properly forwarded to me@domain2. The mail coming from me@domain2 to me@domain1 seems to just get lost in the ether. Have I done something wrong or is this a quark with Exchange? Thanks!

  Read the article

• Prevent chrome from auto-hiding bookmark bar on google search

  - by Jeromy Anglim

  I am using Chrome 28.0.1500.20 beta on OSX 10.7. In this version, when you perform a google search using the address bar the bookmarks bar disappears. Toggling "always show bookmarks bar" does not restore the bookmark (see screenshot below). I want to always show the bookmark bar. In particular, I often use a bookmarklet that converts a current google search into a Google Scholar search. Is there a way to always show the bookmark bar even when performing a Google search in Chrome?

  Read the article

• Bizarre SSH Problem - It won't even start

  - by thallium85

  I recently got Ubuntu 12.04 Precise, got it up and running with some MediaWiki software, static IP on the box and router and was able to access the main page even from a cell phone. Everything seemed great... Then I wanted to finally get rid of the monitor and keyboard and login remotely via SSH. I installed openssh-server, let everything point to port 22 for a test run and installed putty on my Windows XP machine. I got a connection refused. Went back and started checking the Ubuntu install itself... (I'm under root from this point on) $ sudo -s $ service ssh status ssh stop/waiting $ service ssh start ssh start/running, process 2212 $ service ssh status ssh stop/waiting Apparently ssh has stopped or is waiting for something.... $ ssh localhost ssh: connect to host localhost port 22: Connection refused I can't even connect to myself... I checked ufw (firewall) to see if port 22 is doing alright... $ sudo ufw status Status: active To Action From 22 ALLOW Anywhere 22/tcp ALLOW Anywhere 22 ALLOW Anywhere (v6) 22/tcp ALLOW Anywhere (v6) sshd_config shows only Port 22 Is ssh not using the right IP address at all? I just don't get what I did wrong here. When this is up and running I will def change the port number, but for now, I don't want to mess with the default install too much until a test run with putty is successful. Edit: Here are my sshd_config file and my ssh_config file. The command /usr/sbin/sshd -p 22 -D -d -e returns: /etc/ssh/sshd_config line 159: Subsystem 'sftp' already defined. Edit: @phoibus moving the sshd_config file and reinstalling did the trick! service ssh status the above command shows that ssh is now running and I am now able to log in from my windows xp computer remotely via putty. Thanks so much! I can now use my monitor for other things!

  Read the article

• Computer never connects to the internet automatically on startup?

  - by RawR Crew

  I have my Windows Vista laptop connected directly to the router via an ethernet cable, and every time I switch the computer on, the computer cannot connect to the internet. It comes up as limited or no connectivity, I am assuming because it has not been assigned an IP address by the router - not too sure if this is right. The problem is usually fixed either by performing a repair through the networking control panel or removing and re-inserting the ethernet cable. It will also connect without doing any of these if the computer is left idle for about 20 minutes. It will connect fine wirelessly without the need for any of this, however I would prefer to connect via the cable. Any ideas how I can fix this? I have replaced the ethernet cable and router already (identical model) but these haven't helped. Thanks for any help on this.

  Read the article

• Untangle VPN setup, how to see internal addresses?

  - by NFS user

  So Untangle is setup as the default gateway at 192.168.100.1/24, it is the authorative DHCP server issuing addresses from 192.168.100.100 to 192.168.100.200 and is successfully connected to the Internet. Untangle uses OpenVPN for remote access. Accessing the VPN gives me the address 192.168.40.5. However, I cannot ping any machines on the internal 192.168.100.x network remotely. Clearly, there is something basic that I am missing. What is it and how is it solved? Update: The VPN was not setup with the internal network. Since Untangle only allows editing the VPN setup once, the VPN had to be removed and reinstalled with the internal network exported. Now it works. The lesson is that the internal network must be setup before configuring the VPN.

  Read the article

• Windows XP + PAE + 6GB RAM: See more than 3.5GB?

  - by nonot1

  Firstly let me say I've seen a number of similar questions on SuperUser, and I don't think this is a duplicate. (Most address 4GB RAM installed. I have 6GB) I have Windows XP 32-bit running on a i7-based Xeon system with 6GB of RAM. I only see 3.5GB of RAM in Windows. Is there any way to squeeze more visible RAM out of this set up? Even an extra 1GB would be great. Does having 6GB (vs 4GB) of RAM installed help at all? (I.e Even if I loose the 3.5-4.0 GB region, can I use the area above it?) P.S. Will eventually move to Windows 7 64-bit, but can't for now.

  Read the article

• How to efficiently dump a huge MySQL innodb database?

  - by Jagbir

  I got an Ubuntu 10.04 production MySQL database server where total size of database is 260 GB while size of root partition is itself 300 GB where DB is stored, essentially means around 96% of / is full and there's no space left for storing dump/backup etc. No other disk is attached to server as of now. My task is to migrate this database to other server sitting in different datacenter. Question is how to do that efficiently with minimum downtime? I'm thinking in line of: Request to attach an extra drive to server and take a dump in that drive. Transfer dump to new server, restore it and make new server slave of existing one to keep data in sync When migration is needed, break replication, update slave config to accept read/write requests and make old server read-only so it won't entertain any write requests and tell app developers to update there config with new IP address for db. What's your suggestions to improve this or any alternate better approach for this task?

  Read the article

• Routing from the DMZ to the interior network only

  - by Allan

  I have a home network connected to Verizon's FIOS service. Verizon's ActionTec router is connected to the ONT via coax to establish the MOCA network. My DD-WRT router's WAN port is connected to one of the ActionTec's LAN ports. The DD-WRT router is configured with a static IP address and assigned to the DMZ (this is done so I only have to configure port forwarding once). My issue is that this does not allow computers connected to the DD-WRT to serve streaming audio/video to the MOCA network using Verizon's Media Manager. I know that Media Manager uses ports 18001, 5050, and 5060, but I don't know how to forward those ports so that they are only available to the ActionTec's network and not the rest of the internet.

  Read the article

• Limit number of simultaneous connections squid makes to a single server

  - by Ben Voigt

  Note: I am asking about outbound concurrent connection limits, not inbound, which is sufficiently covered on existing questions Modern browsers typically open a large number of simultaneous connections, to take advantage of the fact that TCP fairly shares bandwidth between connections. Of course, this doesn't result in fair sharing between users, so some servers have started penalizing hosts which open too many connections. This limit can be configured client-side (e.g. IE MaxConnectionsPerServer, Firefox network.http.max-connections-per-server), but the method differs for each browser and version, and many users aren't competent to adjust it themselves. So we turn to a squid transparent HTTP proxy for central management of HTTP download. How can the number of simultaneous connections from squid to a remote webserver be limited, so the webserver doesn't perceive it as abuse of concurrent connections? Ideally the limit would be per source address. Squid should accept virtually unlimited concurrent requests from the client browser, and issue them sequentially to the remote server, only N at a time, delaying (but not dropping) the others.

  Read the article

• OpenVPN client on Amazon EC2

  - by Matt Culbreth

  I have an account with an OpenVPN service, and I'd like to get that running on my EC2 instance running Ubuntu 12.04. I have my config file in /etc/openvpn, and it connects fine when I run sudo openvpn --config matt.ovpn. However, I then lose connectivity to the EC2 machine, and I can't SSH back to it until I reboot. Previously I have done things like sudo ip rule add from IP_ADDRESS table 10 and then sudo ip route add default via GATEWAY_IP table 10, but that's not working on EC2. Any ideas? My private IP address right now is 10.209.29.XXX and my gateway is 10.209.29.1.

  Read the article

• why this routing configuration does not work?

  - by avs099

  I have 2 VMs in HyperV role: first is RRAS - it has 2 interfaces (both manually configured, no DHCP): 192.168.1.110 - "external" one, connected to the router 192.168.10.2 - that's internal interface which other VMs will be using as well also I added VPN connection to our main server - and it gets 192.168.2.136 IP address in 192.168.2.XXX network. And IP route is create on the server as well for this interface. second VM is called KITCHENER. It only has 1 interface 192.168.10.99 / 255.255.255.0, with default gateway set to RRAS server - 192.168.10.2 QUESTION: how can I ping "main server" - 192.168.2.1 - from the KITCHENER server when RRAS server is connected to VPN? please see screenshots with ipconfig /all, route print and ping 192.168.2.1 commands. What needs to be done to get this working? all servers are Windows 2008 R2 if that matters.

  Read the article

• Find computer names on a private network (with nmap?)

  - by paracaudex

  On a LAN, I want to find out the names of all the connected computers using a cross-platform program, preferably nmap. I know I can do nmap -sn xxx.xxx.xxx.xxx/24 (where xxx.xxx.xxx.xxx is a local IP address) to find hosts which are up, but how do I find the computers' hostnames? Do they broadcast this in a way that I can find using nmap? UPDATE: It looks like Angry IP Scanner can do this. How does it do this? Can I replicate it with nmap?

  Read the article

• Google Reader can read this RSS feed, why can't my RSS reader?

  - by Nicole

  I have a website that I would like to subscribe to via my RSS reader. The website itself doesn't publicize its RSS feed, however when I used Google Reader it was able to find one, and it works perfectly well. Google Reader cites http://www.stratfor.com/rss.xml as the address for the RSS feed. However, when I try to enter that feed, it says "Page not found". I suspect that this is because that file does exist on the website, but is forbidden; and that for some weird reason google reader has access to it. Is that the case? Anyways, I would really like my own RSS reader to be able to subscribe to it, because it has functionalities that Google reader does not. Besides, it intrigues me -- how come Google reader can read it, but other RSS reader cannot?

  Read the article

• Solution for lightweight LAN peer discovering?

  - by DevilWithin

  I built a library for purely cross-platform programming. My games made with it run fine in Android , Pc, Linux, Mac etc. The networking capabilities are provided by ENET library, therefore all communication between my apps is not TCP or UDP compatible, but only in the custom protocol, even tough its based on the UDP ultimately. I don't think its possible to do what i want with ENET, thats why I ask here for help! Lets say I have the same game running in my Android phone, my laptop and my pc. They are all in the same wifi network, and therefore in a LAN, whether its Wifi hotspot(?) or the household router. I need each of those 3 peers to discover the other two in the network. This is meant only to find the IP of alive apps in the LAN network, to be able to host multiplayer games between them. I can only think of one effective way to do this, UDP broadcast, wait responses, but if that is the solution, i need something small, since its the only purpose of the implementation. Other way could be to try to connect to all IPs in the LAN address subrange, but I don't think the OS would be with me on this one :p Sorry for the long question!

  Read the article

• impossible to connect.. days trying..

  - by dany

  I have a problem: I am on Debian. I configured my nic with a static ip (192.168.1.56). When I try to connect to a network, initially with ifconfig eth2 I get (correctly): eth2 inet addr:192.168.1.56 .... inet6 addr: fe80:221:ff:fe96:4598/64 but after a few seconds the 102.168.1.56 disappears and after some other seconds disappears the inet6 address too. When I press in the nm-applet it requires me the password but in the meantime it try to connect. At uni, the connection is a DHCP one. It works for the first few seconds but after it doesn't. Any possible solution? Here it is the relevant part of the syslog: (static ip configuration) http://pastebin.com/u3BPAsda

  Read the article

• Is 192.168.122.1 a valid IP?

  - by Louise Hoffman

  From my understanding the networks is as follows Class A: 10.0.0.1 - 10.255.255.254 Class B: 172.16.0.1 - 172.16.255.254 Class C: 192.168.0.1 - 192.168.0.254 But then I look at ifconfig virbr0 on my Linux computer: virbr0 Link encap:Ethernet HWaddr 42:40:99:CB:02:7F inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:2842 (2.7 KiB) Here the IP address is 192.168.122.1. Is that an allowed IP? And if so, is 192.168 than actually a Class B network?

  Read the article

• How to install Tor (Web Browser) in Ubuntu 12.10?

  - by Zignd

  I would like to install the Tor, but I'm having some problems. I know that someone will say "This question is a exactly duplication of How to install tor?", but it's not, because the another question can not be applied to Ubuntu 12.10 as the deb command is not available anymore. I did a research and even at the Tor's Official Website the available resource can not be applied to Ubuntu 12.10. I tried to use the deb command (as the above question says: deb http://deb.torproject.org/torproject.org <DISTRIBUTION> main) and the Terminal says deb: command not found and when I try to install it says E: Unable to locate package deb. I've also tried to use the ppa: ubun-tor, but it's not compatible with Quantal Quetzal, because it's too old. I've also tried to use sudo apt-get install tor, but browser icon don't shows up after installation and if you try to use the command tor in the Terminal I get the following error message: Nov 26 10:59:25.731 [notice] Tor v0.2.3.22-rc (git-4a0c70a817797420) running on Linux. Nov 26 10:59:25.731 [notice] Tor can't help you if you use it wrong! Learn how to be safe at https://www.torproject.org/download/download#warning Nov 26 10:59:25.731 [notice] Read configuration file "/etc/tor/torrc". Nov 26 10:59:25.737 [notice] Initialized libevent version 2.0.19-stable using method epoll (with changelist). Good. Nov 26 10:59:25.737 [notice] Opening Socks listener on 127.0.0.1:9050 Nov 26 10:59:25.737 [warn] Could not bind to 127.0.0.1:9050: Address already in use. Is Tor already running? Nov 26 10:59:25.737 [warn] Failed to parse/validate config: Failed to bind one of the listener ports. Nov 26 10:59:25.737 [err] Reading config failed--see warnings above. Thanks in advance.

  Read the article

< Previous Page | 533 534 535 536 537 538 539 540 541 542 543 544  | Next Page >