Search Results

Search found 17081 results on 684 pages for 'body background'.

Page 537/684 | < Previous Page | 533 534 535 536 537 538 539 540 541 542 543 544  | Next Page >

• Disk Activity Alert Windows SBS 2003 on Dell PowerEdge 830 with Raid

  - by Ron Whites

  Background: I have a Dell PowerEdge 830 Server running Windows SB Server 2003. It has 4gbs of RAM and a ATA CERC SATA 6CH controller with 3 160gb drives in a Raid 5 configuration. The Problem I am seeing Admin ---"Disk Activity Alert on Server" emails These often occur when disk backups, de-frag or high disk usage is going on. Generally the server isn't over stressed. The Disk Alert emails say in part ... The following disk has low idle time, which may cause slow response time when reading or writing files to the disk. Disk: 0 C: F: D: Review the Disk Transfers/sec and % Idle Time counters for the PhysicalDisk performance object. If the Disk Transfers/sec counter is consistently below 150 while the % Idle Time counter remains very low (close to 0), there may be a problem with the disk driver or hardware. The Questions I have: With what utility can I review the Disk Transfers/sec and Idle Time? It appears there is no utility for that on the server! I think I may need to download a very large (two DVD) Dell "OpenManage" utility to be able to monitor the raid system and see what is a problem is that true?

  Read the article

• Ubuntu 10.04 network manager issues

  - by Shark

  I was using the default network manager to connect to my wi-fi network, but if the connection is dropped or router restarted the network manager wont reconnect automatically after i guess a couple of tries and just gives a pop-up to connect manually . To avoid this annoyance I installed WICD but though it does try to reconnect to the network after a drop in connection it is unable to resolve the ip address and i am left with an even bigger annoyance . 1. Is there a way to counter either of these issues ? 2. Something like a background process that will check network status periodically and then try to connect to a favored network ? Edit- out put of lshw -C network *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:18:9b:7f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=192.168.11.2 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbc00000-fbc03fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 02 serial: f0:4d:a2:94:2d:74 size: 10MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:29 ioport:e000(size=256) memory:d0b10000-d0b10fff(prefetchable) memory:d0b00000-d0b0ffff(prefetchable) memory:fb200000-fb21ffff(prefetchable)

  Read the article

• What Windows service binds a NIC to the network?

  - by Bigbio2002

  I have a server that takes several minutes for the NIC to bind itself to the network upon startup (it has a statically-configured IP). This causes DNS/WINS/Intersite Messaging to fail to start, since they're dependent on a network connection. While I'm still attempting to find a root cause to this issue (I've done firmware updates, checked for any odd drivers/services, no luck so far), but in the meantime, I want to adjust the load order of services to ensure that the NIC binds first before these services attempt to start. The only question is, which service is it? The server is running Server 2008 R2 and only has one NIC installed. (On a side note, there are two other small but odd problems occuring with the server. The server had the issue described in KB2298620, which I've fixed. The other problem occurs in Windows Server Backup. No events appear in the upper portion of the window, despite the fact that backups are running in the background. Whenever I attempt to modify the backup schedule, it gives me the error "Not enough storage is available to process this command" and appears to fail, when, in fact, it actually succeeds. These may be separate issues, but something tells me that some of these might share a common root cause.)

  Read the article

• DVI output only working on Windows, not during booting or on Linux

  - by Mononofu

  So yesterday I booted my laptop up and the external monitor I have it connected to just stayed black. At first, I thought the problem would go away when Ubuntu was loaded, but it didn't. I tried to reboot a few times, to no avail. Then I decided to give Windows 7 a try, and suddenly (at the login-screen), my external monitor turned on and worked like normal. I have connected the monitor via DVI, and this only seems to work with Windows now. I don't even get a signal in my BIOS! Mind you, everything was working fine before that, and I didn't change a single thing. I then tried to connect the monitor via VGA (from my DVI jack, which can output VGA using an adaptor), and it worked again. However, 1920x1200 using VGA looks like crap - black print on white background is basically illegible. Do you have any ideas how to fix this peculiar problem? I only use windows for gaming, so it's no real help that it still works normally. Please also excuse any spelling mistakes, I am practically typing this blindly. Edit: I only have one graphics card in my laptop, and I can't select anything related to that in my BIOS. In fact, I can pretty much do almost nothing there. My laptop is a Nexoc Osiris E703, graphics gard is a GeForce Go 7900 GTX. As I mentioned before, DVI output during booting and on Ubuntu was working fine for years before yesterday!

  Read the article

• Make reading more comfortable for the eyes

  - by Shiki

  First, I read the topics about displays. Sadly the "BenQ FP241WZ" is a no go, for ~715 eur it's way too much. I would need some ideas about how could I make reading less tiring. Basically I didn't have this problem back then. But now, I'm reading some books, and also, have to read a lot a day. (A LOT). I look like some hardcore 0-24 gamer when I "finish" :). Think about things like.. background color (like I read 'dark yellow' color + black tint helps), font size, fonts (!) cleartype settings (should be off?) and so on. Display: BenQ E2200 HD (yeah cheap, eek, etc. Poor-man's LCD. :)) My CRT display is far away at the minute. So that is out of question. Also, my ThinkPad is here (T500), but I don't know about it's display. It comes with 1280x800 resolution and that's all I know (you can search back from that the FRU number, but I couldn't find it now). What could I do? (Or basically everyone in such a situation?)

  Read the article

• Spam or exchange issue?

  - by John

  I am getting an error message to unknow user on my domain. I would like to know is this just a phishing spam email or it was really send from our domain? I have changed our domain name to OURDOMAIN.COM I have Exchange 2010 installed. Body of the email is Delivery has failed to these recipients or distribution lists: sales The recipient's e-mail address was not found in the recipient's e-mail system. Microsoft Exchange will not try to redeliver this message for you. Please check the e-mail address and try resending this message, or provide the following diagnostic text to your system administrator. Sent by Microsoft Exchange Server 2007 Diagnostic information for administrators: Generating server: murraygroup.local [email protected] #550 5.1.1 RESOLVER.ADR.RecipNotFound; not found ## Original message headers: Received: from ironport.mih.co.uk (10.10.29.9) by mih-exca-01.murraygroup.local (10.10.29.133) with Microsoft SMTP Server id 8.3.106.1; Fri, 29 Jun 2012 12:36:12 +0100 Received: from glamf04.netintelligence.com (HELO mailfilter.iomart.com) ([62.128.193.114]) by ironport.mih.co.uk with SMTP; 29 Jun 2012 12:42:48 +0100 Received: from glamta4.netintelligence.com(localhost.localdomain[127.0.0.1]) by mailfilter.iomart.com ; Fri, 29 Jun 2012 12:37:18 BST Received: from [195.43.137.66] ([195.43.137.66]) by glamta4.netintelligence.com (8.13.1/8.12.8) with ESMTP id q5TBbH4j022142 for <[email protected]>; Fri, 29 Jun 2012 12:37:18 +0100 Date: Fri, 29 Jun 2012 12:37:17 +0100 Message-ID: <20120629145229.4C2A817231D8A7958044@SONW> From: Ines Hampton <[email protected]> To: sales <[email protected]> Reply-To: Marguerite Soto <[email protected]> Subject: User sales MIME-Version: 1.0 Content-Type: text/plain; charset="utf-8" Content-Transfer-Encoding: 7bit Return-Path: [email protected] eporting-MTA: dns;murraygroup.local Received-From-MTA: dns;ironport.mih.co.uk Arrival-Date: Fri, 29 Jun 2012 11:36:12 +0000 Final-Recipient: rfc822;[email protected] Action: failed Status: 5.1.1 Diagnostic-Code: smtp;550 5.1.1 RESOLVER.ADR.RecipNotFound; not found X-Display-Name: sales

  Read the article

• What does Firefox do when "scanning for viruses" after download?

  - by Joey

  Never mind the fact that Firefox is a browser and not a AV tool, but what exactly does it do after a download? Even on systems that have an up-to-date AV this generates a pause of several seconds after download (where I can't open the file from within the DL manager) and I have no idea what FF might be trying there. I know I can turn it off (using FF only at work anyway) but I'm wondering. I can think of some things here what it might be: FF itself is a AV scanner and it loads signatures in the background and whatnot. Sounds highly unlikely and shouldn't need tens of seconds for 20 KiB files. FF tries to talk with the installed AV to munch the file. Sounds unneeded, given that most AV programs feature real-time protection anyway and therefore will have caught a virus already and also because FF does that on systems without AV installed too. FF uploads the file to some online virus checker. Unlikely and stupid. FF instructs some online virus checker to download the file and check it. Unlikely and would be a nice target for DoSing that service. FF generates a hash of the file and sends that somewhere (presumably Google) to check for. They then respond with either "Whoa, that hash is totally a virus" or "Nope, that MD5 doesn't look very virus-y to me". I'm running out of better ideas. Anyone have a clue?

  Read the article

• Can I configure Thunderbird 3 to refresh the folder list for an Exchange IMAP account?

  - by Howiecamp

  Background: When used as an IMAP client against Gmail, Thunderbird 3 (may be the case in v2 also, not sure) will refresh it's list of folders (the folders correspond to Gmail labels) when you do "Download/Sync Now..." or restart the Thunderbird client. Any new folders (labels) created in Gmail will sync to the client and any folders moved/changed/deleted folders in Gmail will move/change/delete on the client as well. (Note: Thunderbird has the concept of "subscribing" to IMAP folders (assumingly allowing you to determine which folders you want, rather than bringing all of them down and dragging loads of data across the wire). When used against Gmail, Thunderbird appears to automatically subscribe to all folders (including when folders are newly created in Gmail), so this might be why the refresh is happening properly.) This behavior is what I want with Exchange. When using Thunderbird with Exchange (2007), the folder list doesn't refresh when folders are added/changed/deleted on the server and/or from a different mail client. When I look at the subscription options, some are checked and some are not (not sure why Thunderbird picked some and not others). And when I add new folders on the server and/or from another client, they never even appear in Thunderbird's list of folders, preventing me from subscribing to them.

  Read the article

• Spotlight has stopped indexing/returning anything in /Applications

  - by pra

  After a recent kernel panic & restart, Spotlight no longer seems to know anything about the files under my /Applications folder. I used to launch Safari.app, Opera.app, Textedit.app, etc via Spotlight as a matter of routine. Now, I get "No results found" for all of them (except Textedit.app, which launches a demo text editor from a Qt installation). The programs are still there & still launch directly from Finder. I've already run disk utility & verified the disk, no issues. I repaired disk permissions, which made several changes, but to no effect. Is there anything else I can do, short of re-installing MacOS? Update: I already verified that "Applications" was still checked in my Spotlight preferences. It was still returning applications located elsewhere (the Qt textedit sample app), so that shouldn't have been the issue. A few hours later it resolved itself; I guess there's a background process running on some interval.

  Read the article

• Installing Visual Studio Express on Windows 8.1

  - by robrene

  I've been trying to install the latest version of Microsoft Visual Studio Express from their website to toy around with the IDE and C# development in general. I have a relatively fresh and completely vanilla installation of Windows 8.1 Professional x64 for this purpose. I come from a Linux background, where installing software (especially software distributed by the maintainer of the OS) is usually done with package managers. First, I tried to look for Visual Studio in the Windows 8 Store. There was one entry, but it did not have an installation button. Instead, it redirected me to their website. From all the products listed under the "Download" section on their website, I decided Visual Studio 2013 Express for Windows Desktop was the best for me. I selected it and clicked on "Install now". An installer program downloaded, and I'm assuming that the installer downloaded the necessary files as it was running. When it was done, it asked for a reboot, to which I obliged. However, I can't seem to find the IDE installed anywhere? It doesn't show up anywhere in the Start menu interface. I can't find any executables that look like they might be the IDE in its installation folder. Running the installer again and selecting "Repair" does download some files, but after its requested reboot, nothing has changed. The only thing that I can find is an advertisement link to "Try other Visual Studio 2013 Products" in my start menu. I suppose my question is what I have to do to run Visual Studio 2013 Express on Windows 8.1? Am I not looking in the right places? Am I doing the installation process wrong? Thanks in advance

  Read the article

• How to force the start and end date of a task in Microsoft Project to be on the same day?

  - by Hauke P.

  I have a task called "Interview person A about topic X". The task's duration is set to 2 hours. The start date of the task should automatically be calculated taking dependencies and resource availabilities into account. My question boils down to: How can I force this task to start and end on the same date? Background: In my case, Microsoft Project sets the start date to a Friday at 5pm. As my working hours are set to 8am to 12am and 1pm to 6pm (Mon-Fri), Microsoft Project "splits up" the task at 6pm on Friday and plans to continue it at 8am on the following Monday. However, it does not make any sense to stop the interview on a Friday and restart it on Monday. Therefore the automatic suggestion is not helpful in this case. That's why I'm looking for a way way to force the task to start and end on the very same day. (In my example, I'd like Microsoft Project to delay the start date of the task until Monday 8am as this is the first time slot in which the task "fits in completely".) By the way: I have lots of such cases... for that reason it would be really great if there was a solution that doesn't just deal with this single special case.

  Read the article

• How to install Red Hat Enterprise Linux on Apple Macbook Pro MacBookPro4,1

  - by Todd V. Rovito

  I have a one year old Mac Book Pro that I am trying to get RHEL 5.4 installed on via bootcamp. No matter what I do I can't get the installer to boot. I have tried multiple DVD's and even verified the install works on a new Mac Book Pro. Most of the time the installer simply locks up. I usually use Linux text with all-generic-ide on the boot line. I removed the ide parameter and I just used linux text. The results I get are that a bunch of kernel messages appear then the background turns blue and a thin text box pops up saying its loading ata..... something it disappears too fast for me to read. Then the machine freezes. I pressed the alt function keys to see if I could look at the system log, here is what it says: Alt-f3 says "trying to mount CD device hda" Alt-f4 says status error: hda: lastFailedSense Hda: Failed opcode was: unknown Hda: Lost interrupt Hda: Drive not ready for command Ide-cd: command 0x3 timed out Above this junk it looks like it found the partition because it knew it was 20 GB and listed as /dev/sda3. I think it has something to do with the CD drive, is that possible? Thanks again for the support. PS I posted in the apple support forums ( Apple.com Support Discussions Boot Camp Installation and Storage) and didn't get an answer.

  Read the article

• Apache displays error page half way through PHP page execution

  - by Shep

  I've just installed Zend Server Community Edition on a Windows Server 2003 box, however there's a bit of a problem with the display of a lot of our PHP pages. The code has previously running under the same version of PHP (5.3) on IIS without any issues. By the looks of things, Apache (installed as part of Zend Server) is erroring out during the rendering of the page when it comes across something it doesn't like in the PHP. Going through the code, I've been able to get past some of the problems by removing the error suppression operator (@) from function calls and by changing the format of some includes. However, I can't do this for the whole site! Weirdly, the error code is reported as "200 OK". The code snippet below shows how the Apache error HTML interrupts the regular HTML of the page. <p>Ma quande lingues coalesce, li grammatica del resultant lingue es plu simplic e regulari quam ti del coalescent lingues.</<!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>200 OK</title> </head><body> <h1>OK</h1> <p>The server encountered an internal error or misconfiguration and was unable to complete your request.</p> <p>Please contact the server administrator, [email protected] and inform them of the time the error occurred, and anything you might have done that may have caused the error.</p> <p>More information about this error may be available in the server error log The Apache error log doesn't offer any explanation for this, and I've exhausted my Googling skills, so any help would be greatly appreciated. Thanks.

  Read the article

• Playback random section from multiple videos changing every 5 minutes

  - by brian

  I'm setting up the A/V for a holiday party this weekend and have an idea that I'm not sure how to implement. I have a bunch of Christmas movies (Christmas Vacation, A Christmas Story, It's a Wonderful Life, etc.) that I'd like to have running continuously at the party. The setup is a MacBook connected to a projector. I want this to be a background ambiance thing so it's going to be running silently. Since all of the movies are in the +1 hour range, instead of just playing them all through from beginning to end, I'd like to show small samples randomly and continuously. Ideally the way it would work is that every five minutes it would choose a random 5-minute sample from a random movie in the playlist/directory and display it. Once that clip is over, it should choose another clip and do some sort of fade/wipe to the chosen clip. I'm not sure where to start on this, beginning with what player I should use. Can VLC do something like this? MPlayer? If there's a player with an extensive scripting language (support for rand(), video length discovery, random video access). If so, I will probably be able to RTFM and get it working; it's just that I don't have time to backtrack from dead-ends so I'd like to start off on the right track. Any suggestions?

  Read the article

• Can ZFS ACL's be used over NFSv3 on host without /etc/group?

  - by Sandra

  Question at the bottom. Background My server setup is shown below, where I have an LDAP host which have a group called group1 that contains user1, user2. The NAS is FreeBSD 8.3 with ZFS with one zpool and a volume. serv1 gets /etc/passwd and /etc/group from the LDAP host. serv2 gets /etc/passwd from the LDAP host and /etc/group is local and read only. Hence it doesn't not know anything about which groups the LDAP have. Both servers connect to the NAS with NFS 3. What I would like to achieve I would like to be able to create/modify groups in LDAP to allow/deny users read/write access to NFS 3 shared directories on the NAS. Example: group1 should have read/write to /zfs/vol1/project1 and nothing more. Question The problem is that serv2 doesn't have a LDAP controlled /etc/group file. So the only way I can think of to solve this is to use ZFS permissions with inheritance, but I can't figure out how and what the permissions I shall set. Does someone know if this can be solved at all, and if so, any suggestions? +----------------------+ | LDAP | | group1: user1, user2 | +----------------------+ | | | |ldap |ldap |ldap | v | | +-----------+ | | | NAS | | | | /zfs/vol1 | | | +-----------+ | | ^ ^ | | |nfs3 |nfs3| v | | v +-----------------------+ +----------------------------+ | serv1 | | serv2 | | /etc/passwd from LDAP | | /etc/passwd from LDAP | | /etc/group from LDAP | | /etc/group local/read only | +-----------------------+ +----------------------------+

  Read the article

• Nginx: Loopback connection via PHP's getimage size crashes server (Magento's CMS)

  - by Alex

  We were able to trace down a problem that is crashing our NGINX server running Magento until the following point: Background info: Magento Backend has a CMS function with a WYSIWYG editor. This editor loads some pictures via a controller in magento (cms/directive). When we set the NGINX error_log level to info, we get the following lines (line break inserted for better readability): 2012/10/22 18:05:40 [info] 14105#0: *1 client closed prematurely connection, so upstream connection is closed too while sending request to upstream, client: XXXXXXXXX, server: test.local, request: "GET index.php/admin/cms_wysiwyg/directive/___directive/BASEENCODEDIMAGEURL,,/ HTTP/1.1", upstream: "fastcgi://127.0.0.1:9024", host: "test.local" When checking the code in the debugger, the following call does never return (in ´Varien_Image_Adapter_Abstract::getMimeType()` # $this->_fileName is http://test.local/skin/adminhtml/base/default/images/demo-image-not-existing.gif` # $_SERVER['REQUEST_URI'] = http://test.local/admin/cms_wysiwyg/directive/___directive/BASEENCODEDIMAGEURL list($this->_imageSrcWidth, $this->_imageSrcHeight, $this->_fileType, ) = getimagesize($this->_fileName); The filename requests is an URL to the same server which is requesting the script a link to a static .gif that is not existing. Sample URL: http://test.local/skin/adminhtml/base/default/images/demo-image-not-existing.gif When the above line executed, any subsequent request to the NGNIX server does not respond any more. After waiting for around 10 minutes, the NGINX server starts answering requests again. I tried to reproduce the error with a simple test script that only calls getimagesize() with the given URL - but this not crash. It simple leads to an exception saying that the URL could not be loaded (which is fine as the URL is wrong)

  Read the article

• Trying to Set up SMTP Server on WIndows Server 2012

  - by datc

  I'm working on a website, and I need to test the functionality of sending email messages from ASP.NET, something like this: Dim msg As New MailMessage("email1", "email2") msg.Subject = "Subject"<br> msg.IsBodyHtml = True<br> msg.Body = "Click <a href='site'>here</a>." Dim client As SmtpClient = New SmtpClient() client.Host = "My-Server"<br> client.Port = 25<br> client.DeliveryMethod = SmtpDeliveryMethod.Network<br> client.Send(msg) This is running from a Windows 8 workstation. I've installed SMTP server on my Windows Server 2012 machine. The mail shows up in the mailroot/Queue folder and sits there, eventually getting deposited into Badmail. Now I have AT&T U-verse at home, and a few devices connected to the gateway, including let's call it "My-Server." When I run SmtpDiag from say, datc@... to [email protected] I get SOA serial number match passed, Local DNS (99-135-60-233.lightspeed.bcvloh.sbcglobal.net) & Remote DNS (hotmail.com) tests *not* passed, and ultimately, Connecting to the server failed. Error: 10060. Failed to submit mail to mx2.hotmail.com error. When I set My-Server's IP to static and equal to the external IP, 99.135.60.233, and again run SmtpDiag, I get SOA, Local DNS, and Remote DNS tests passed, but the same 10060 error. Same for yahoo.com, gmail.com, and so forth. Is it my ISP's job to fix this? Some PTR record missing somewhere? Is it at all possible to have a home-based SMTP server? All I want is to test my email code. Perhaps, my IP address is just not "trusted" somehow. Thanks.

  Read the article

• How do I enable Ubuntu Gnome system tools

  - by RussellW

  I am running Ubuntu 10 with Gnome 2.30.2. This is a VMWare workstation image provided by another company that I do not have support in this regard. I am trying to access the graphical tools for configuring the network, users, and services but the System-Administration menu does not have these options listed. The main issue I am trying to solve is to correct the problems with the gnome menu options and network settings I have the gnome-system-tools package installed, and I am unable to run command-line versions of the tools, such as nm-applet (I get no GUI if I run that command, the process is running in the background). I realize that I can perform many tasks command-line, but I would like to use the GUI for administrative functions as I am not overly proficient for all command for restarting services and setting a static IP with a specific gateway. Further, I can run gnome-nettool, but I cannot change the IP, I can only see my network card. nm-connection-editor does not show any network cards that I can configure to change the IP. Currently, I am getting a DHCP through my NAT in VMWare, I want to set it to a specific IP address though. Preferences Menu (note some missing options) ![Preferences Menu][1] Admin Menu (note some missing options) ![Admin Menu][2] Network Tools (I can view but not change IP address) ![Network Tools][3] Network Settings (Unable to change IP address) ![Network Settings][4] Network Connections (no connections listed, not even my existing ethernet NAT connection through VMWare) ![Network Connections][5] See images here that I have referenced: 1- http://i.imgur.com/kl8pP.png 2- http://i.imgur.com/K3Cjz.png 3- Iq7Xb.png 4- 7wheV.png 5- J2ad8.png

  Read the article

• One Way Sync with Dropbox?

  - by user244805

  Is there any way I can mirror a dropbox folder to my C drive by just running a portable file? Extra background information because I know you guys hate it when you don't get the entire situation: I go back to University in fall and I need a new storage solution. I decided to use DropBox to sync my tiny University files (< 5 MB). I need to access these files from 4 machines: Windows 7 Home machine Windows 7 University A machine Windows 7 University B machine Android tablet 1 and 4 are a non-issue. The problem lies with 2 and 3. I want to be able to edit my files on 2 and 3 but those machines are not mine. There is an easy fix. Run a portable version of the DropBox syncer on a USB drive. But the problem is that I don't want to carry a USB drive around with me all the time. In that case, I can just run the small portable DropBox syncer off the internet. But where will it to store the files? A temporary directory on the C drive. There is only one issue left: there are hundreds of machines that I will randomly use that fit in categories 2 and 3. My portable DropBox syncer will notice that the temporary directory is empty on each new PC I use and instead of downloading my DropBox folder to the machine, it syncs the other way around i.e. it deletes my entire DropBox. The solution is to mirror my DropBox onto the temporary directory before running the DropBox syncer.

  Read the article

• Fixed ruby/mysql connection with new libmysql.dll, and broke Apache in the process

  - by jmtoporek

  Ok so bit of background - all my development has been on a local Windows 7 machine. I had Apache with PHP/MySQL running with no issues. Been using ruby (1.9.3 and latest rails release 3.2.9) with built in webrick server, but had a devil of a time connecting to mysql. Did some research, updated my libmysql.dll file in c:/ruby/bin and it worked! Very happy... except now Apache stopped working. In my attempt to resolve the issue I found an older copy of libmysql.dll, renamed the new file, copied the old file back to c:ruby/bin and apache works, ruby does not. So I can take this ass backwards approach but obviously this seems pretty stupid. I was surprised that Apache was using the dll file in ruby/bin folder. I presume this is related to path variables perhaps? I guess I was hoping someone could direct me as to how I can use one dll file for apache and another for ruby. Or if you have some other smarter approach - I've smart enough to follow directions to install apache from scratch and enable php on windows as well as ubuntu, but I'm not much of a sys admin, just a semi competent web developer.

  Read the article

• Is it possible to record a screen-video from a VNC server?

  - by nikie

  I have a computer that's running VNC server. I would like to record a video of what's going on on this computer, if possible without installing additional software on that computer. Is there a program that can connect to the VNC server port and instead of displaying the screen save it to an (e.g. AVI) video file? Background: One of our customers sometimes has problems with the software he bought from us when he's performing a complex procedure. To help him, we offered that someone (a service technician or programmer) watches what he's doing during that procedure to find out if he's doing something wrong or if there's a bug in the software. Currently, this is done live via VNC. That has a few disadvantages: The service technician has to be in the office at the time. As the customers are in different time zones, that can be in the middle of the night. If the service technician forgets something or doesn't notice something, it's lost. There's no way to see what happened again. Only a single computer can be watched by one service technician at a time. I know I could install normal screen-grab software on the computer, but we're talking about an embedded system with limited RAM, CPU, HDD space, so installing something new is not an easy decision. And VNC is already there. I could of course open a VNC client on some office PC and capture that PC's screen, but I can only record one remote computer that way. I often have to watch up to 8 screens in parallel. (And I don't think that screen-grabbing VNC would improve image quality, either.)

  Read the article

• Questions about NGINX limit_req_zone

  - by Meteor

  I got a problem with NGINX limit_req_zone. Anyone can help? The problem is that, I want to limit user access to some specific URL, for example: /forum.php?mod=forumdisplay? /forum.php?mod=viewthread&*** But, I do want to add an exception for below URL, /forum.php?mod=image&* Below is the location section of my configuration, the problem is that, for URL started with /forum.php?mod=image&*, the limitation is still applied. Any body can help? location ~*^/forum.php?mod=image$ { root /web/www; fastcgi_pass unix:/tmp/nginx.socket; fastcgi_param SCRIPT_FILENAME /scripts$fastcgi_script_name; include fastcgi_params; } location ~*^/(home|forum|portal).php$ { root /web/www; limit_conn addr 5; limit_req zone=refresh burst=5 nodelay; fastcgi_pass unix:/tmp/nginx.socket; fastcgi_param SCRIPT_FILENAME /scripts$fastcgi_script_name; include fastcgi_params; } location ~ \.php$ { root /web/www; fastcgi_pass unix:/tmp/nginx.socket; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /scripts$fastcgi_script_name; include fastcgi_params; }

  Read the article

• Redis connection issue

  - by mre

  We are currently experiencing a lot of Redis errors with the message Unable to connect: read error on connection, trying next server We run Redis on FreeBSD using PHP Redis and we have a hard time reproducing the error on Ubuntu so this might be a hint. There's a long-running issue on that topic on github. Basically we get a socket from the operating system with a call to connect(host, port, timeout) in phpredis, but when we do a select(db_index) afterwards, we get an exception. Could there be an issue with persistance? I assume that connect does nothing in the background and select tries to access the connection, which is actually closed. We don't run into a timeout. We tried tuning TIME_WAIT without success. Any other ideas on where the problem might come from? What is the best way to track the issue down? dtrace maybe? Update We are currently looking into our BGSAVE settings. Interestingly it takes half a second and more to create a fork for the process which regularly writes the data to disk (persistence) and maybe redis can't respond to connect() requests during that timespan.

  Read the article

• Is it possible to command a common router without using the web interface?

  - by MDeSchaepmeester

  Some background The internet arrangement in my student home is really weird. There is one ethernet outlet and several wifi hotspots. Either way requires a login through a web site to get internet access. This is annoying as each device needs to login seperately and with a PS3 for example, it is impossible to get connected at all since the web login procedure doesn't work. Therefore I have installed a D-Link DIR-635 router which is connected to the ethernet outlet. It has DHCP enabled so it uses NAT, but whatever it is connected to also uses NAT and I've read this should not work. A fellow student tried it with an Apple Airport but that keeps giving errors related to NAT after NAT. Anyway my setup does work so bonus points if you can clarify this. I need to login to the web site I mentioned earlier with any device, after which all devices in my LAN have connectivity. This is great. Except... In short From time to time, I lose internet connectivity and my D-Link DIR-635 router needs to do a DHCP renew. I can do this via the web interface but my life would be easier if I could just run a cmd file which tells my router to do this without all the hassle. This would setup a connection to my router and execute the proper command. I have tried googling but couldn't find much helpful stuff.

  Read the article

• Active Directory FRS problems. 13508 error and other problems

  - by user59232

  I have 3 Domain Controllers. We will call them DC1, DC2 and DC3. DC3 and DC2 show Event ID 13508 in their FRS logs with no follow-up event(13509 I think) to say the error had been fixed. DC1's FRS log no matter what you do never shows any events besides FRS service stopped and started. DC1 holds the SYSVOL that needs to be replicated to the other DC's. The other DC's sysvol folders are empty. I have tried the burflag method of fixing this but I haven't had any luck. My procedure for that was to stop all FRS services on all DC's. Then set the burflag on DC1 to D4 and the other two DCs burflag to D2. Started FRS on DC1 and the only event's I see in DC1's FRS event logs are service stopped and service started messages. This fact is leading me to believe that something is wrong on FRS for DC1. I believe there should be events 13553 and 13516 in the FRS event logs after an authoritative sysvol restore. The other two DC's do not have anything in their SYSVOL, otherwise I would have made one of them the authoritative sysvol. DC1 is MS Server 2003 Enterprise Edition SP2 DC2 is MS Server 2003 Standard Edition SP1 DC3 is MS Server 2003 R2 Standard Edition SP2 I did not setup this domain originally but I am now the administrator of it, so I don't have a lot of background on why certain things may have been done in the past. My main goal is to try and fix these issues to get myself better prepared to decommision DC1 and add a DC running Server 2008 to my domain. Thanks.

  Read the article

< Previous Page | 533 534 535 536 537 538 539 540 541 542 543 544  | Next Page >