Search Results

Search found 14292 results on 572 pages for 'high integrity systems'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 537/572 | < Previous Page | 533 534 535 536 537 538 539 540 541 542 543 544  | Next Page >

  • Cisco 678 Will Not Work using PPPoE - Possibly Because I Configured it Incorrectly..?

    - by Brian Stinar
    I am attempting to configure a Cisco 678 because I am totally sick on my Actiontec. However, I am running into some problems. It seems as though the Cisco is able to train the line, but I am unable to ping out. I am all right at programming, but still learning a lot when it comes to being a system administrator. I apologize in advance if I did something ridiculous, or am attempting to configure this device to do something it was not designed to do. It is almost like I am not correctly configuring the device to grab it's IP using PPPoA (like my Actiontec.) The output from "show running" (below) makes me think this too. Below are the commands I ran in order to configure this: # en # set nvram erase # write # reboot # en # set nat enable # set dhcp server enable # set PPP wan0-0 ipcp 0.0.0.0 # set ppp wan0-0 dns 0.0.0.0 # set PPP wan0-0 login xxxxx // My actual login # set PPP wan0-0 password yyyyy // My actual password # set PPP restart enabled # set int wan0-0 close # set int wan0-0 vpi 0 # set int wan0-0 vci 32 # set int wan0-0 open # write # reboot Here is the output from a few commands I thought could provide some useful information: cbos#ping 74.125.224.113 Sending 1 8 byte ping(s) to 74.125.224.113 every 2 second(s) Request timed out cbos#show version Cisco Broadband Operating System CBOS (tm) 678 Software (C678-I-M), Version v2.4.9 - Release Software Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Nov 17 2004 15:26:29 DMT FULL firmware version G96 NVRAM image at 0x1030f000 cbos#show errors - Current Error Messages - ## Ticks Module Level Message 0 000:00:00:00 PPP Info IPCP Open Event on wan0-0 1 000:00:00:14 ATM Info Wan0 Up 2 000:00:00:14 PPP Info PPP Up Event on wan0-0 3 000:00:01:54 PPP Info PPP Down Event on wan0-0 Total Number of Error Messages: 4 cbos#show interface wan0 wan0 ADSL Physical Port Line Trained Actual Configuration: Overhead Framing: 3 Trellis Coding: Enabled Standard Compliance: T1.413 Downstream Data Rate: 1184 Kbps Upstream Data Rate: 928 Kbps Interleave S Downstream: 4 Interleave D Downstream: 16 Interleave R Downstream: 16 Interleave S Upstream: 4 Interleave D Upstream: 8 Interleave R Upstream: 16 Modem Microcode: G96 DSP version: 0 Operating State: Showtime/Data Mode Configured: Echo Cancellation: Disabled Overhead Framing: 3 Coding Gain: Auto TX Power Attenuation: 0dB Trellis Coding: Enabled Bit Swapping: Disabled Standard Compliance: T1.413 Remote Standard Compliance: T1.413 Tx Start Bin: 0x6 Tx End Bin: 0x1f Data Interface: Utopia L1 Status: Local SNR Margin: 19.0dB Local Coding Gain: 7.5dB Local Transmit Power: 12.5dB Local Attenuation: 46.0dB Remote Attenuation: 31.0dB Local Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 2 No Cell Delineation Interleaved: 0 Out of Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 Remote Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 1 No Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 cbos#show int wan0-0 WAN0-0 ATM Logical Port PVC (VPI 0, VCI 32) is configured. ScalaRate set to Auto AAL 5 UBR Traffic IP Port Enabled cbos#show running Warning: traffic may pause while NVRAM is being accessed [[ CBOS = Section Start ]] NSOS MD5 Enable Password = XXXX NSOS MD5 Root Password = XXXX NSOS MD5 Commander Password = XXXX [[ PPP Device Driver = Section Start ]] PPP Port User Name = 00, "XXXX" PPP Port User Password = 00, XXXX PPP Port Option = 00, IPCP,IP Address,3,Auto,Negotiation Not Required,Negotiable ,IP,0.0.0.0 PPP Port Option = 00, IPCP,Primary DNS Server,129,Auto,Negotiation Not Required, Negotiable,IP,0.0.0.0 PPP Port Option = 00, IPCP,Secondary DNS Server,131,Auto,Negotiation Not Require d,Negotiable,IP,0.0.0.0 [[ ATM WAN Device Driver = Section Start ]] ATM WAN Virtual Connection Parms = 00, 0, 32, 0 [[ DHCP = Section Start ]] DHCP Server = enabled [[ IP Routing = Section Start ]] IP NAT = enabled [[ WEB = Section Start ]] WEB = enabled cbos# wtf...? Thank you all very much for taking the time to read this, and the help.

    Read the article

  • What NAS setup for two-way syncing over the internet?

    - by Jamse
    I have family living a few hours away and have a lot of files that I would like to share - especially lots of folders of digital photos, but also documents etc. - partially so they can see them, partially so I can have access when I visit them and partially for backup / redundancy purposes. My current hard drives on my main machine are getting pretty full anyway, and I have a MythTV box where my music is currently stored, so I was thinking of getting a NAS anyway. And at the other end my family have a few computers, so they would probably benefit from a NAS too. My general idea (though I'm willing to shift on this if there are any bright ideas about other ways of achieving my objectives) is to get a matching pair of NASs and have them sync over the internet. (To cut down on bandwidth use I would get them in sync locally to start with.) Having read around as best I can it seems that syncing over the internet is generally only a feature on quite high end units. However, I have seen that QNAP seem to feature this on their TS-110 and TS-210 units, which might work (they call it "remote replication"). They seem pretty reasonably priced for what they are, but of course with buying 2 of them and then adding the drives (say 1TB or 2TB each) I'd be looking at about £400 total. So, I'm looking for recommendations really. I don't want to spend more than the QNAPs would cost me, but any other ideas would be most appreciated. I am comfortable with technology and tinkering around, but I don't have as much time for that as I would like, so I guess I would favour solutions that require less tinkering rather than more (even though that's less fun!). Any thoughts would be welcome, as would any comments from people who have used the QNAP boxes for this. Thanks in advance. Some specifications: Two-way syncing. Changes made at either end should be synced to the other. There shouldn't be one unit that is effectively a read-only mirror of the other. Not real time. The syncing doesn't need to be real time - if it updated, say, daily overnight that would be fine. Set and forget. I would prefer minimal user interaction once set up - it would be great if syncs were scheduled and automatic. OS independence. I am running Windows XP plus an Ubuntu-based MythTV box. At the other end there are Windows 7 and Windows XP machines, plus a networked TV set top box which I think can play files off the network. Machine independence. I would favour a system that is self-contained, i.e. not reliant on any particular PC being switched on. If the system had enough else going for it I could perhaps work around it at this end, where I only have one PC that's used as such, but it would be harder at the other where there are at least two PCs that might be accessing the files. Notifications. I guess things like getting an email notification if the syncing fell over for any reason would be useful, though it's not a deal breaker. Update I've been digging some more and it looks like QNAP's Remote Replication function is actually just Rsync, so only really suitable for one-way syncing. I've posted on their forum to double check, but I think that's the case. In which case, I think the focus of my question is now either: do any reasonably-priced NASs support bidirectional syncing over the internet?, or has anyone had any luck installing onto NASs for this purpose? (Also, updated question to clarify that I'm after two-way syncing.)

    Read the article

  • Drupal & nginx : a sound "general purpose" configuration?

    - by sbrattla
    After a bit back and forth with configuring Drupal and nginx to work together, I've come up with the below configuration for a site. It works well, both with private and public file systems. However, as I am fairly new to nginx I'd like to hear if there is something with this configuration that I should change (for Please note! I'm aiming towards getting feedback on a general purpose Drupal configuration. That is, a configuration which others who are trying out Drupal + nginx can "copy paste" to get up and running. server { listen 80; server_name www.example.* example.*; access_log /home/example/www/logs/access.log; error_log /home/example/www/logs/error.log; root /home/example/www/public_html; # Site Icon location = /favicon.ico { log_not_found off; access_log off; } # Search Engines location = /robots.txt { allow all; log_not_found off; access_log off; } # Drush location = /backup { deny all; } # Very rarely should these ever be accessed from outside # the local network. location ~* \.(txt|log)$ { allow 10.0.0.0/8; allow 172.16.0.0/12; allow 192.168.0.0/16; deny all; } location ~ \..*/.*\.php$ { return 403; } # Default location location / { try_files $uri @rewrite; } # Files managed by Drupal will be served via PHP. location ~* /system/files/ { access_log off; try_files $uri @rewrite; } ## Images and static content is treated different location ~* \.(jpg|jpeg|gif|css|png|js|ico|xml)$ { access_log off; expires 30d; } # Some Drupal modules enforce no slash (/) at the end # of the URL. location @rewrite { rewrite_log on; rewrite ^/(.*)$ /index.php?q=$1; } # PHP5-FPM is used to handle PHP. location ~ \.php$ { fastcgi_split_path_info ^(.+\.php)(.*)$; fastcgi_pass unix:/var/run/example.sock; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_intercept_errors on; fastcgi_ignore_client_abort off; fastcgi_connect_timeout 60; fastcgi_send_timeout 180; fastcgi_read_timeout 180; fastcgi_buffer_size 128k; fastcgi_buffers 4 256k; fastcgi_busy_buffers_size 256k; fastcgi_temp_file_write_size 256k; } ## Disable viewing .htaccess & .htpassword location ~ /\.ht { deny all; } }

    Read the article

  • Just a few questions about Hyper-V virtual machines and clustering

    - by René Kåbis
    I have been using Microsoft’s Hyper-V technology for a little while now, but I am just now dipping my toe into clustering. In particular, I am trying to implement a fault-tolerant SQL DB. This involves setting up two VMs, clustering them via Failover Cluster, and then installing SQL Server in some fashion. I have two physical machines - one high-end and rather beefy “heavy lifter” to contain the majority of the VMs, and another “backup” (a repurposed desktop) to hold the essential “secondary” (or failover) AD-DC, SQL and FS VMs. The main reason why I find the failover cluster at the VM level so attractive is that it presents a single IP and DNS entry to the network as a whole - if one machine (physical or virtual) goes down, you might loose some ping and the connections get reset, but the network applications (Microsoft RMS connection to backend SQL) can still connect to a viable DB without having to mess around with the settings at all. My first question is in terms of SQL Server itself. If I have a cluster between two VMs, does it make more sense to install the SQL Server in Failover Cluster configuration or should I simply install it in a stand-alone config and mirror the DBs? For example, this post suggests just mirroring the DBs, but do I just mirror standalone DBs on standalone VMs, or can I get the network and failover benefits of clustered VMs while still utilizing (on each clustered VM) standalone DBs that have been mirrored between each other? As well, I have come across a lot of documentation about SQL clustering, but most assume a number (#2) of physical machines to hold not only the actual SQL VMs but also the Quorum and Witness stores. I will not be able to muster more than two physical machines. As such, I will have to be satisfied with a VM cluster that does not exceed two VMs (one for each physical machine). Another issue involves MSDTC - the Distributed Transaction Coordinator. When attempting to install the SQL Failover Cluster (I never completed it for this reason) it threw a hissy fit because MSDTC had not been clustered. Search as I might, I have not yet found a way to do so under Windows Server 2012 R2. I have found plenty of docs for Windows 2008 and 2008 R2, but these instructions don’t align with 2012 R2 (at least, not in a way that allows me to successfully cluster MSDTC). Plus, some of the instructions that I have found for SQL Server Failover Cluster installation suggest that a third “network device” - shared network storage (a SAN) - is required for the DB itself (and other functionality). I do not have this, and won’t be getting this. Most of my storage exists on the “heavy lifter” that was designed for all of the “primary” VMs. If that physical machine goes down, so does the storage. The secondary server does have enough resources for an AD-DC Server, an SQL server and a File Server, so it will handle the “secondary” failover versions of those VMs (clustered or not). My final question involves file servers. If I cluster file servers between two VMs (one on my “heavy lifter” and another on my “backup”, how do I mirror the data between them? Clustering VMs only provides a single point of access on the network for a resource, it doesn’t exactly replicate data between the two - that is left to the services that serve up that data. I am unsure how I can ensure that file server data between two clustered file server VMs can be properly mirrored. Remember, I only have two devices to be used here - my primary machine and a backup secondary. There is no chance of me obtaining a SAN or any other type of network attached storage. What exists on the machines must act as the storage. Thanks in advance for any suggestions.

    Read the article

  • Samba doesnt require password on xbmc but does on ubuntu

    - by Chris
    I have samba setup on a fedora 13 machine, and I use it to share with my xbmc client in the family room. When I set this up there no password or anything was required I merely entered in paths such as: smb://<host>/<share> and all worked. Now on my ubuntu 10.04 machine when I try to access the same hosts, for example through smbmount though I receive an error. smbmount //media/Music ~/Music/ # media is in my /etc/hosts and resolves to # correct IP address for the machine I receive error: operation not permitted after pressing enter when it prompts for password. Here is my entry from /etc/samba/smb.conf: [global] workgroup = WORKGROUP server string = Samba Server Version %v # log files split per-machine: log file = /var/log/samba/log.%m # maximum size of 50KB per log file, then rotate: max log size = 50 security = user passdb backend = tdbsam ; security = domain ; passdb backend = tdbsam ; realm = MY_REALM ; password server = <NT-Server-Name> ; security = user ; passdb backend = tdbsam ; domain master = yes ; domain logons = yes ; logon script = %m.bat ; logon script = %u.bat ; logon path = \\%L\Profiles\%u ; logon path = ; add user script = /usr/sbin/useradd "%u" -n -g users ; add group script = /usr/sbin/groupadd "%g" ; add machine script = /usr/sbin/useradd -n -c "Workstation (%u)" -M -d /nohome -s /bin/false "%u" ; delete user script = /usr/sbin/userdel "%u" ; delete user from group script = /usr/sbin/userdel "%u" "%g" ; delete group script = /usr/sbin/groupdel "%g" ; local master = no ; os level = 33 ; preferred master = yes ; wins support = yes ; wins server = w.x.y.z ; wins proxy = yes ; dns proxy = yes load printers = yes cups options = raw ; printcap name = /etc/printcap # obtain a list of printers automatically on UNIX System V systems: ; printcap name = lpstat ; printing = cups ; map archive = no ; map hidden = no ; map read only = no ; map system = no ; store dos attributes = yes #============================ Share Definitions ============================== [homes] comment = Home Directories browseable = no writable = yes ; valid users = %S ; valid users = MYDOMAIN\%S # Un-comment the following and create the netlogon directory for Domain Logons: ; [netlogon] ; comment = Network Logon Service ; path = /var/lib/samba/netlogon ; guest ok = yes ; writable = no ; share modes = no # Un-comment the following to provide a specific roving profile share. # The default is to use the user's home directory: ; [Profiles] ; path = /var/lib/samba/profiles ; browseable = no ; guest ok = yes # A publicly accessible directory that is read only, except for users in the # "staff" group (which have write permissions): ; [public] ; comment = Public Stuff ; path = /home/samba ; public = yes ; writable = yes ; printable = no ; write list = +staff [tv] comment = TV path = /media/Isos/tv public = yes writable = yes printable = no write list = +media [music] comment = Music path = /media/Storage/music/ public = yes writable = yes printable = no write list = +media [pictures] comment = Pictures path = /media/Storage/pictures public = yes writable = yes printable = no write list = +media

    Read the article

  • How to stop windows resizing when the monitor display channel is turned off / switched to different source

    - by Heartspeace
    Have a new 6870 ati radeon adapter with its drivers set to 1080p 60hz resolution hooked up to a 2008 47" high end Samsung HDMI based TV. However, when the tv is turned to a different hdmi input -(when I come back into windows) somehow Windows decides to resize all the open apps to a lower resolution - including some of the side docked hidden pop-outs. When it resizes those though - it just sticked the pop-outs in the middle of the screen and all the resized windows from the open applications in the top left corner - all of them stacked on top of each other and resized to the smaller resolution. The things that seem to be ok after returning are the icons on the desktop, the taskbar, and the sidebar. Anyone have any knowledge of 1) how this happens 2) why it happens 3) how to stop it from resizing the applications and some of the docked pop-outs (they are not really resized after returning - they are just stuck in the middle of the screen approximately where they would be if the right or bottom sidebar should be if the screen was resized to that lower resolution). My hypothesis is that upon losing HDMI signal - that Windows is told by something (driver, or windows itself) that the resolution to be without a signal being present (noting that HDMI signals and handshakes are two way on HDMI devices. If it loses the signal or the tv is switched to another device - then the display adapter must figure that out and tell Windows or figures it out and designs randomly to change the display size). Any and all help is most appreciated. I asked AMD/ATI - but they said they don't know why or how this is happening. I was hoping that maybe this is THE place that the super users truly go to - those that develop display adapter drivers, or that dive deeply into these areas of windows. If there is better sites or just competing sites - please advise - noting I have already written AMD/ATI. HP Response / Additions 4/7/2011 It is really nice to get your reply Shinrai. (BTW is it proper etiquette on these forums to have a discussion?) Yet 'only one issue' - I am using a single display in this case - so Windows doesn't move application windows to another desktop. Windows (or something) decides to shrink the desktop it currently has and resize all windows to the maximum size of the desktop. As such I would be glad if Windows would just keep the current size of the one desktop that is in operation. I also know that this does NOT happen on monitors connected with DVI. There I have had one and two monitors setup and it doesn't resize those screens at all when disconnecting monitors, turning them off, whatever... they stay solid - everything in place - to such an extent that if you forgot the other monitor is off - you will have troubles finding some windows without using one of the control app utilities. So if I could even get the HDMI handling by Windows (or the display driver) ( 1] which is doing this anyway the display driver or Windows - and 2] where is that other resolution size (1024x768) coming from - its not the smallest and its not the largest?) to be having like DVI - Life would be golden (for this aspect anyway). ** found others with same problem in this thread: http://hardforum.com/showthread.php?t=1507324 Thanks, HP

    Read the article

  • what is best config for nginx worker_rlimit_nofile and worker_connections 28672

    - by Binh Nguyen
    i have issue of web-brower response ( especially on ie ) very slow, some time time out, and sometime hang out up to 20 seconds for one file redirect 301 when test with "f12 derverloper tool of ie" .. it report wait/start time very long. but after got connected the elements on web weill be dowload and show out fast ( test at xaluan.com ) It most happen when active user on web more than 2100 ( use google real time live analytic ). server running cenos 5 with ngix, apache, 32core cpu, 96G ram, raid 10 sas hdd.. == flowing is my config == user nobody; # no need for more workers in the proxy mode worker_processes 28; #old 32 #good at 24 error_log /var/log/nginx/error.log; #old add in end: info worker_rlimit_nofile 22528; events { worker_connections 22528; use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 25; #old 5 gzip on; #old on gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 6; gzip_buffers 16 8k; ignore_invalid_headers on; client_header_timeout 1m; #3m client_body_timeout 1m; #3m send_timeout 1m; #3m reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 100M; client_body_buffer_size 256k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; limit_conn_zone $binary_remote_addr zone=limit_per_ip:1m; limit_conn limit_per_ip 20; limit_req_zone $binary_remote_addr zone=allips:5m rate=200r/s; limit_req zone=allips burst=200 nodelay; include "/etc/nginx/vhosts/*"; } =========== I have play around with worker config 1- tried increase as some one suggess: worker_rlimit_nofile = worker_connections = worker_processes * 1024 = 32768 2- tried to set low: worker_processes = 28 and other worker at 22582 and other solution too .. but not work cause some time it make server load hight very quick 3- tried to comment out the # worker_rlimit_nofile . so it will be unlimited. it look like solved a bit about issue response time. but it also make server high load quick in peak time... Please help thanks PS: other apache you may have look for help me out thanks Listen 0.0.0.0:8081 User nobody Group nobody ExtendedStatus On ServerAdmin [email protected] ServerName server.xaluan.com LogLevel warn # These can be set in WHM under 'Apache Global Configuration' Timeout 100 TraceEnable Off ServerSignature Off ServerTokens ProductOnly FileETag None StartServers 15 <IfModule prefork.c> MinSpareServers 20 MaxSpareServers 50 #MaxSpareServers 40 </IfModule> ServerLimit 1572 MaxClients 1572 MaxRequestsPerChild 4000 # MaxRequestsPerChild 3000 KeepAlive On KeepAliveTimeout 3 MaxKeepAliveRequests 300 #MaxKeepAliveRequests 130

    Read the article

  • Where is my VMware-ws FreeNAS CIFS(ZFS) bottle-neck?

    - by maka
    Background: I'm building a quiet HTPC + NAS that is also supposed to be used for general computer usage. I'm so far generally happy with things, it was just that I was expecting a little better IO performance. I have no clue if my expectations are unreal. The NAS is there as a general purpose file storage and as a media server for XBMC and other devices. ZFS is a requirement. Question: Where is my bottle-neck, and is there anything I can do config wise, to improve my performance? I'm thinking VM-disk settings could be something but I really have no idea where to go since I'm neither experienced with FreeNAS nor VMware-WS. Tests: When I'm on the host OS and copy files (from the SSD) to the CIFS share, I get around 30 Mbytes/sec read and write. When I'm on my laptop laptop, wired to the network, I get about the same specs. The test I've done are with a 16 GB ISO, and with about 200 MB of RARs and I've tried avoiding the RAM-cache by reading different files than the ones I'm writing ( 10 GB). It feels like having less CPU cores is a lot more efficient, since the resource manager in Windows reports less CPU-usage. With 4 cores in VMware, CPU usage was 50-80%, with 1 core it was 25-60%. EDIT: HD ActiveTime was quite high on SSD so I moved the page file, disabled hibernate and enabled Win DiskCache both on SSD and RAID. This resulted in no real performance difference for one file, but if i transferred 2 files the total speed went up to 50 Mbytes/s vs ~40. The ActiveTime avg also went down a lot (to ~20%) but has now higher bursts. DiskIO is on ~ 30-35 Mbytes/s avgs, with ~100Mb bursts. Network is on 200-250Mbits/s with ~45 active TCP connections. Hardware Asus F2A85-M Pro A10-5700 16GB DDR3 1600 OCZ Vertex 2 128GB SSD 2x Generic 1tb 7200 RPM drives as RAID0 (in win7) Intel Gigabit Desktop CT Software Host OS: Win7 (SSD) VMware Worksation 9 (SSD) FreeNAS 8.3 VM (20GB VDisk on SSD) CPU: I've tried 1, 2 and 4 cores. Virtualisation engine, Preferred mode: Automatic 10,24Gb ram 50Gb SCSI VDisk on the RAID0, VDisk is formatted as ZFS and exposed through CIFS through FreeNAS. NIC Bridge, Replicate physical network state Below are two typical process print-outs while I'm transfering one file to the CIFS share. last pid: 2707; load averages: 0.60, 0.43, 0.24 up 0+00:07:05 00:34:26 32 processes: 2 running, 30 sleeping Mem: 101M Active, 53M Inact, 1620M Wired, 2188K Cache, 149M Buf, 8117M Free Swap: 4096M Total, 4096M Free PID USERNAME THR PRI NICE SIZE RES STATE TIME WCPU COMMAND 2640 root 1 102 0 50164K 10364K RUN 0:25 25.98% smbd 1897 root 6 44 0 168M 74808K uwait 0:02 0.00% python last pid: 2746; load averages: 0.93, 0.60, 0.33 up 0+00:08:53 00:36:14 33 processes: 2 running, 31 sleeping Mem: 101M Active, 53M Inact, 4722M Wired, 2188K Cache, 152M Buf, 5015M Free Swap: 4096M Total, 4096M Free PID USERNAME THR PRI NICE SIZE RES STATE TIME WCPU COMMAND 2640 root 1 76 0 50164K 10364K RUN 0:52 16.99% smbd 1897 root 6 44 0 168M 74816K uwait 0:02 0.00% python I'm sorry if my question isn't phrased right, I'm really bad at these kind of things, and it is the first time I post here at SU. I also appreciate any other suggestions to something, I could have missed.

    Read the article

  • can't access nginx server from IP

    - by EquinoX
    So 2 days ago I can see that page where it saya "Welcome to nginx", however as of now when I tried to access it, it says 404 page not found... Why is this? Inside my sites-enabled folder I have a file named default and it has the following: # You may add here your # server { # ... # } # statements for each of your virtual hosts server { listen 80; server_name 127.0.0.1; access_log /var/log/nginx/localhost.access.log; location / { root /var/www/nginx-default; index index.html index.htm; } location /doc { root /usr/share; autoindex on; allow 127.0.0.1; deny all; } location /images { root /usr/share; autoindex on; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # #error_page 500 502 503 504 /50x.html; #location = /50x.html { # root /var/www/nginx-default; #} # proxy the PHP scripts to Apache listening on 127.0.0.1:80 # #location ~ \.php$ { #proxy_pass http://127.0.0.1; #} # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www/nginx-default$fastcgi_script_name; include fastcgi_params; } # deny access to .htaccess files, if Apache's document root # concurs with nginx's one # location ~ /\.ht { deny all; } } # another virtual host using mix of IP-, name-, and port-based configuration # #server { #listen 8000; #listen somename:8080; #server_name somename alias another.alias; #location / { #root html; #index index.html index.htm; #} #} # HTTPS server # #server { #listen 443; #server_name localhost; #ssl on; #ssl_certificate cert.pem; #ssl_certificate_key cert.key; #ssl_session_timeout 5m; #ssl_protocols SSLv2 SSLv3 TLSv1; #ssl_ciphers ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP; #ssl_prefer_server_ciphers on; #location / { #root html; #index index.html index.htm; #} #} Here's my nginx.conf file: user www-data; worker_processes 4; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } # mail { # # See sample authentication script at: # # http://wiki.nginx.org/NginxImapAuthenticateWithApachePhpScript # # # auth_http localhost/auth.php; # # pop3_capabilities "TOP" "USER"; # # imap_capabilities "IMAP4rev1" "UIDPLUS"; # # server { # listen localhost:110; # protocol pop3; # proxy on; # } # # server { # listen localhost:143; # protocol imap; # proxy on; # } # } What am I doing wrong here? I have other virtual host setup in the sites-enabled as well... UPDATE: The server_name directives are: -admin.api.frapi -api.frapi -default -example.com -php.example.com

    Read the article

  • Postfix not sending/allowing receiving of messages after server (hardware) changed

    - by 537mfb
    We had na old notebook runing Ubuntu 12.04 working as a web/ftp/mail server and it worked but since the notebook was a notebook and pretty old and unreliable, a desktop was bought to replace it before it stopped working all together. Due to issues with the new desktop's vídeo card, we couldn't use Ubuntu 12.04 so we installed Ubuntu 13.10 and wen't about configuring it. Since we removed the notebook from the network, we kept the same Computer Name and local IP address to make things as close to the old server as possible configuration-wise. However, something has gone wrong since Postfix is throwing error 451 4.3.0 lookup faillure on every attempt to send a mail, and no email can be received either. Our main.cf file is a copy of the one we were using (and working) on the old server (notice we use EHCP) # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name powered by Easy Hosting Control Panel (ehcp) on Ubuntu, www.ehcp.net biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no myhostname = m21-traducoes.com.pt relayhost = mydestination = localhost, 89.152.248.139 mynetworks = 127.0.0.0/8, 192.168.0.0/16, 172.16.0.0/16, 10.0.0.0/8, 89.152.248.0/24 virtual_alias_domains = virtual_alias_maps = proxy:mysql:/etc/postfix/mysql-virtual_forwardings.cf, proxy:mysql:/etc/postfix/mysql-virtual_email2email.cf transport_maps = proxy:mysql:/etc/postfix/mysql-virtual_transports.cf virtual_mailbox_domains = proxy:mysql:/etc/postfix/mysql-virtual_domains.cf virtual_mailbox_maps = proxy:mysql:/etc/postfix/mysql-virtual_mailboxes.cf virtual_mailbox_base = /home/vmail virtual_uid_maps = static:5000 virtual_gid_maps = static:5000 smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous broken_sasl_auth_clients = yes smtpd_recipient_restrictions = permit_mynetworks,permit_sasl_authenticated,check_client_access hash:/var/lib/pop-before-smtp/hosts,reject_unauth_destination smtp_use_tls = yes smtpd_use_tls = yes smtpd_tls_auth_only = no smtpd_tls_CAfile = /etc/postfix/cacert.pem smtpd_tls_cert_file = /etc/postfix/smtpd.cert smtpd_tls_key_file = /etc/postfix/smtpd.key smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_session_cache_timeout = 3600s tls_random_source = dev:/dev/urandom virtual_create_maildirsize = yes virtual_mailbox_extended = yes virtual_mailbox_limit_maps = proxy:mysql:/etc/postfix/mysql-virtual_mailbox_limit_maps.cf virtual_mailbox_limit_override = yes virtual_maildir_limit_message = "The user you are trying to reach is over quota." virtual_overquota_bounce = yes debug_peer_list = sender_canonical_maps = debug_peer_level = 1 proxy_read_maps = $local_recipient_maps $mydestination $virtual_alias_maps $virtual_alias_domains $virtual_mailbox_maps $virtual_mailbox_domains $relay_recipient_maps $canonical_maps $sender_canonical_maps $recipient_canonical_maps $relocated_maps $mynetworks $virtual_mailbox_limit_maps $transport_maps alias_maps = hash:/etc/aliases smtpd_relay_restrictions = permit_mynetworks, permit_sasl_authenticated,check_client_access hash:/var/lib/pop-before-smtp/hosts,reject_unauth_destination smtpd_destination_concurrency_limit = 2 smtpd_destination_rate_delay = 1s smtpd_extra_recipient_limit = 10 disable_vrfy_command = yes smtpd_delay_reject = yes smtpd_helo_required = yes smtpd_error_sleep_time = 1s smtpd_soft_error_limit = 10 smtpd_hard_error_limit = 20 This configuration was working before but now everytime i try to send a mail in squirrelmail it reports: Message not sent. Server replied: Requested action aborted: error in processing 451 4.3.0 <[email protected]>: Temporary lookup failure And i can't send mail to it from outsider either. Any ideas? EDIT: Here are some issues MXToolBox reports to my domain, answering hopefully to @Teun Vink: BlackList Mail Server Web Server DNS Error 4 0 2 0 Warnings 0 0 0 3 Passed 0 6 3 12 So the domain is on some blacklist, but that doesn't explain the error at all No mail server issues found (except it's not working) Those two web server errors it's because i don't have HTTPS workin (No SSL Certificate) so the test fails Those 3 DNS warnings we're already there when it was working with the other machine and are related to stuff i can't control: SOA Refresh Value is outside of the recommended range SOA Expire Value out of recommended range SOA NXDOMAIN Value too high I've searched and as far as i can tell only the guys who sold the retail can change those values and they won't. Edit2: I half solved the issue.on the new machine postfix was installed but postfix-mysql waasn't so he couldn't connect to the database (rookie mistake). After fixing that, i can now send mails to the outsider without any issues, however i am still not able to receive mails from utside. The sender doesn't get any message warning about the non-delivery but the message doesn't fall in the inbox and the log shows: Nov 13 15:11:57 m21-traducoes postfix/smtpd[5872]: NOQUEUE: reject: RCPT from re lay4.ptmail.sapo.pt[212.55.154.24]: 451 4.3.5 <relay4.ptmail.sapo.pt[212.55.154. 24]>: Client host rejected: Server configuration error; from=<[email protected]> to=<[email protected]> proto=SMTP helo=<sapo.pt> Nov 13 15:11:57 m21-traducoes postfix/smtpd[5872]: disconnect from relay4.ptmail .sapo.pt[212.55.154.24]

    Read the article

  • Static file download from browser breaking in varnish but works fine in Apache

    - by Ron
    I would at first like to thank everyone at serverfault for this great website and I also come to this site while searching in google for various server related issues and setups. I also have an issue today and so I am posting here and hope that the seniors would help me out. I had setup a website on a dedicated server a few days ago and I used Varnish 3 as the frontend to Apache2 on a Debian Lenny server as the traffic was a bit high. There are several static file downloads of around 10-20 MB in size in the website. The website looked fine in the last few days after I setup. I was checking from a 5mbps + broadband connection and the file downloads were also completed in seconds and working fine. But today I realized that on a slow internet connection the file downloads were breaking off. When I tried to download the files from the website using a browser then it broke off after a minute or so. It kept on happening again and again and so it had nothing to do with the internet connection. The internet connection was around 512 kbps and so it was not dial up level speed too but decent speed where files should easily download though not that fast. Then I thought of trying out with the apache backend port and used the port number to check out if the problem occurs. But then on adding the apache port in the static file download url, the files got downloaded easily and did not break even once. I tried it several times to make sure that it was not a coincidence but every time I was using the apache port in the file download url then it was downloading fine while it was breaking each time with the normal link which was routed through Varnish I suppose. So, it seems Varnish has somehow resulted in the broken file downloads. Could anyone give any idea as to why it is happening and how to fix the problem. For more clarification, take this example: Apache backend set on port 8008, Varnish frontend set on port 80 Now when I download say http://mywebsite.com/directory/filename.extension Then the download breaks off after a minute or so. I cannot be sure it is due to the time or size though and I am just assuming. May be some other reason too. But when I download using: http://mywebsite.com:8008/directory/filename.extension Then the file download does not break at all and it gets download fine. So, it seems that varnish is somehow creating the file download breaking and not apache. Does anybody have any idea as to why it is happening and how can it be fixed. Any help would be highly appreciated. And my varnish default.vcl is backend apache { set backend.host = "127.0.0.1"; set backend.port = "8008"; } sub vcl_deliver { remove resp.http.X-Varnish; remove resp.http.Via; remove resp.http.Age; remove resp.http.Server; remove resp.http.X-Powered-By; }

    Read the article

  • USB connection is unstable with Nexus S 2.3.4 on AMD 64 running 64-bit Windows 7, but works with 32-bit Windows Vista

    - by Mike
    The USB connection is unstable with Nexus S (Android 2.3.4) on AMD 64 running 64-bit Windows 7, but it works with 32-bit Windows Vista. Problem Description: On the 64-bit Windows 7 machine my Nexus S appears to connect, but then it disconnects moments later. Neither accessing USB storage or loading an Android application package file (APK) using the Android Debug Bridge (ADB) work. On 32-bit Windows Vista using the same USB cable, USB storage works. I haven't tried the ADB on 32-bit Windows Vista. Reproduction steps for USB storage: (I have provided the reproduction steps for USB storage and not ADB, because if one isn't working, then the other isn't working either and the USB storage reproduction steps are shorter to document.) Connect the USB cable to the Nexus S and my Windows 7 machine. Effect: The "USB Mass Storage, USB Connected" dialog appears with the button "Turn on USB storage." Click "Turn on USB Storage" Effect: The "working circle" appears. A dialog briefly appears saying "USB storage in use," then it either returns me to Step 1 (now that I am running 2.3.4) or is replaced with the Nexus S's application homepage (while I was running 2.3.3). I'm not sure if the version matters, but I mention it for completeness. On the 32-bit Windows Vista machine the connection is stable. I am able to navigate through the Nexus S file system create, read, update, and delete files, etc. I haven't tried connecting with the ADB. Troubleshooting summary: Tried and failed: Uninstalling and reinstalling the Android USB drivers including removing the files. Uninstalling my custom software Pulling the Nexus S's battery Restarting the Nexus S Restarting 64-bit Windows 7 Changing USB ports on the 64-bit Windows 7 box Compared the dates and file size on the DLLs in my google-usb_driver\amd64 directory and the windows\System32 directory. They match. The sizes for the google-usb_driver\i386 directory do not match (expected). Turning off Debugging mode on the Nexus S does not resolve the problem. Searching Google. Tried and succeeded: Connecting to another machine (Windows Vista) using the same USB cable and Nexus S phone. Troubleshooting observations: I notice that uninstalling the device drivers and deleting the files, then reinstalling the drivers, then rebooting 64-bit Windows 7 then unplugging the Nexus S, then plugging it back in occasionally helps for a short amount of time (minutes to hours, not days). When it is working, I can both access the Nexus S's drive and load/test applications using the ADB. I have observed some wonky behavior in the Device Manager that I haven't tracked down. Sometimes the black Nexus S image appears in the list of devices. Sometimes the image displays as a computer with a green ISA card. Sometimes it neither appears on the top level of devices nor under “other devices,” but it does appear under "disk drives" as "Android UMS Composite USB Device." System configuration: The Nexus S is running Android OS 2.3.4's "Settings\about phone\System updates" indicates that it is up to date as of May 21st 2011. Both 32-bit Windows Vista and 64-bit Windows 7 are up to date. The Windows Vista system is running on an Intel 32-bit processor. Windows 7 is running on an AMD 64-bit processor. I have done Android development on both systems, but I usually develop on the 64-bit Windows 7 machine.

    Read the article

  • Choice of an OS for a home ZFS NAS

    - by OlafM
    I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post. UPDATES Given the first answers, I will strongly suggest the person paying the hardware to insert a second HD. Better 2x2TB than 1x3TB (3 TB is oversized anyway). I was trying to keep the initial costs down to spread them over a longer period, but better having something good from the beginning.

    Read the article

  • BSOD Code 16, artifacts all over the place (gtx 260)

    - by belinea
    I have a following, quite dated rig E8400 Core 2 Duo cpu Intel Dragontail Peak DP35DP motherboard on Intel Bearlake P35 chipset 4GB ram Geforce 260gtx Corsair 650W PSU Windows 7 64 bit The following things has happened in the last few days. I first decided to update my Nvidia drivers to the latest version. That was 4 days ago. PC worked fine for 2 days and I was able to play few games as well without any problems. Then 2 days ago a first crash happened while playing the new XCOM game. BSOD code 16. Just the blue screen, no artifacts. PC rebooted and worked well again, I continued playing this game for another 2 hours and went to sleep. Next evening I tried to play some BF3 multiplayer (use to play on LOW settings). Approx. 10 minutes into the game red/pink-ish artifacts appeared on the screen and game quit to desktop. Restarted the game and another 3-4 minutes afterwards another crash to desktop but this time followed shortly by BSOD Code 16. From that moment I started to seeing artifacts on random startups, including Windows loading screen and the BIOS itself. Windows would still load but soon enough it would BSOD on a simple task like opening a Internet browser. Today I get tons of artifacts (little small red dashes all over the screen) on BIOS, loading screen, normal Windows mode as well as safe mode. I suspect it wouldn't be drivers but I tried removing and sweeping them entirely in the safe mode. PC would still start with artifacts all over the place but would load the normal mode, just without the driver, in the default lowest resolution. As soon as proper Nvidia drivers are installed though and PC rebooted, Windows doesn't load at all as BSOD now appears on loading screen. However, again, if I go to safe mode and remove drivers, normal mode launches fine. So obviously crash happens only on high resolution. I opened my machine this morning and gave it a proper cleaning even though it wasn't heavily dusted. It didn't help and number of artifacts seems to increase with every PC restart. I write these words in safe mode, which works, but I have to look through all the red dots and dashes. I don't have built in GPU chipset so I can't try removing my Geforce card nor can I borrow A GPU from anyone else. What are my options? I was looking into getting a completely new rig around Christmas so I'm not freaking out about this. If everything points to hardware issue I may simply decide to get the new machine earlier and don't bother with fixing this one. However it would be great to learn more if this is indeed situation that has slim chances of getting sorted. I realize BSOD Code 16 is rather popular topic online but every story seems a bit different and there can be number of issues with it. Hence a new thread.

    Read the article

  • Configuring a PIX 506e for Asterisk

    - by orthogonal3
    Hi all! I'm having problems configuring a old Cisco PIX running 6.3 and wondered if anyone can lend a hand? Simply put I have a PIX 506e that I want to put in my VoIP data path. I can't update it and getting a compat version of Java for that version of PIX is tough so I can't log onto the web interface. The PIX straddles two networks..... 192.168.5.0 on the inside, ...50.0 on the outside both net masks are 255.255.255.0 I have a local Asterisk server cluster with a single service IP (<local asterisk>) SIP is on UDP 5060 and RTP (for the voip data) is on UDP 18000-18999 I know thats a big range but hey may as well. I need the 192.168.5.0 net to have web and ftp access for updates and the like. DHCP, DNS and NTP is already provided on that network so I don't need external DNS access. So I think I want the following rules: SIP or RTP from <my itsp> arriving at <outside voip ip> NATed to <local asterisk> SIP or RTP able to do the reverse route (should be covered by high sec - low sec??) HTTP and FTP access outbound for software update for the servers etc I have the following config at the minute - and I think I'm almost there (I hope)... interface ethernet0 auto interface ethernet1 auto nameif ethernet0 outside security0 nameif ethernet1 inside security100 enable password wouldyouliketobeapeppertoo encrypted passwd wouldyouliketobeapeppertoo encrypted hostname afirewall domain-name adomain fixup protocol dns maximum-length 512 fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 access-list acl_ping permit icmp any any access-list voip permit ip host <my itsp> host <local asterisk> mtu outside 1500 mtu inside 1500 ip address outside <outside pix ip> 255.255.255.0 ip address inside <inside pix ip> 255.255.255.0 arp timeout 14400 global (outside) 1 <outside generic ip> nat (inside) 1 192.168.5.0 255.255.255.0 0 0 static (inside,outside) <outside voip ip> <local asterisk> netmask 255.255.255.255 0 0 static (outside,inside) <local asterisk> <outside voip ip> netmask 255.255.255.255 0 0 access-group acl_ping in interface outside access-group acl_ping in interface inside route outside 0.0.0.0 0.0.0.0 <my next hop router> 1 route outside <my itsp> 255.255.255.255 <my next hop router> 1 I think I just need a hand with the access-lists and NAT/static rules. Would anyone be able to help as I've RTFM'd the Cisco docs a few times and they're heavy. Wishing I'd completed my CCNA now! Thanks all for any help, Phil

    Read the article

  • What NAS setup for syncing over the internet?

    - by Jamse
    I have family living a few hours away and have a lot of files that I would like to share - especially lots of folders of digital photos, but also documents etc. - partially so they can see them, partially so I can have access when I visit them and partially for backup / redundancy purposes. My current hard drives on my main machine are getting pretty full anyway, and I have a MythTV box where my music is currently stored, so I was thinking of getting a NAS anyway. And at the other end my family have a few computers, so they would probably benefit from a NAS too. My general idea (though I'm willing to shift on this if there are any bright ideas about other ways of achieving my objectives) is to get a matching pair of NASs and have them sync over the internet. (To cut down on bandwidth use I would get them in sync locally to start with.) Having read around as best I can it seems that syncing over the internet is generally only a feature on quite high end units. However, I have seen that QNAP seem to feature this on their TS-110 and TS-210 units, which might work (they call it "remote replication"). They seem pretty reasonably priced for what they are, but of course with buying 2 of them and then adding the drives (say 1TB or 2TB each) I'd be looking at about £400 total. So, I'm looking for recommendations really. I don't want to spend more than the QNAPs would cost me, but any other ideas would be most appreciated. I am comfortable with technology and tinkering around, but I don't have as much time for that as I would like, so I guess I would favour solutions that require less tinkering rather than more (even though that's less fun!). Any thoughts would be welcome, as would any comments from people who have used the QNAP boxes for this. Thanks in advance. Some specifications: Two-way syncing. Changes made at either end should be synced to the other. There shouldn't be one unit that is effectively a read-only mirror of the other. Not real time. The syncing doesn't need to be real time - if it updated, say, daily overnight that would be fine. Set and forget. I would prefer minimal user interaction once set up - it would be great if syncs were scheduled and automatic. OS independence. I am running Windows XP plus an Ubuntu-based MythTV box. At the other end there are Windows 7 and Windows XP machines, plus a networked TV set top box which I think can play files off the network. Machine independence. I would favour a system that is self-contained, i.e. not reliant on any particular PC being switched on. If the system had enough else going for it I could perhaps work around it at this end, where I only have one PC that's used as such, but it would be harder at the other where there are at least two PCs that might be accessing the files. Notifications. I guess things like getting an email notification if the syncing fell over for any reason would be useful, though it's not a deal breaker.

    Read the article

  • Pushing DNSSEC updates with offline keys

    - by eggyal
    In a non-professional capacity, I look after the DNS of some 18 domains: mostly personal/vanity domains for immediate family. I outsource the whole shebang to an inexpensive managed hosting provider with a web interface through which I manage the zones; since the provider also offers DNSSEC, I have successfully deployed that too. These domains are so unimportant that an attack targetted against them seems much less likely than a general compromise of my provider's systems, at which point the records of all their customers might be changed to misdirect traffic (perhaps with extremely long TTLs). DNSSEC could protect against such an attack, but only if the zone's private keys are not held by the hosting provider. So, I wonder: how can one keep DNSSEC private keys offline yet still transfer signed zones to an outsourced DNS host? The most obvious answer (to me, at least) is to run one's own shadow/hidden master (from which the provider can slave) and then copy offline-signed zonefiles to the master as required. The problem is that the only machine I (want to*) control is my personal laptop, which usually connects from a typical home ADSL (behind NAT over a dynamically-assigned IP address). Having them slave from that (e.g. with a very long Expiry time on the zone for periods when my laptop is offline/unavailable) would not only require a Dynamic DNS record from which they can slave (if indeed they can slave from a named host rather than a static IP address), but would also involve me running a DNS server on my laptop and opening both it and my home network up to the incoming zone transfer requests: not ideal. I would prefer a much more push-oriented design, whereby my laptop initiates transfer of offline-signed zonefiles/updates to the provider's servers. I looked into whether nsupdate could fit the bill: documentation is a little sketchy, but my testing (with BIND 9.7) suggests it can indeed update DNSSEC zones, but only where the server holds the keys to perform the zone signing; I have not found a way to have it take an update including the relevant RRSIG/NSEC/etc. records and have the server accept them. Is this a supported use-case? If not, I suspect the only solutions which could fit the bill will involve non-DNS-based transfer of the zone updates and would welcome recommendations that are supported by (hopefully inexpensive) hosting providers: SFTP/SCP? rsync? RDBMS replication? Proprietary API? Finally, what would be the practical implications of such a setup? Key rotation is jumping out at me as being an obvious difficulty, especially if my laptop is offline for extended periods. But the zones are extremely stable, so perhaps I could get away with long-lived ZSKs**...? * Whilst I could run a shadow/hidden master on e.g. an outsourced VPS, I dislike the overhead of having to secure / manage / monitor / maintain yet another system; not to mention the additional financial costs of so doing. ** Okay, this would enable a concerted attacker to replay outdated records—but the risk and impact of such are both tolerable in the case of these domains.

    Read the article

  • IPv6: Should I have private addresses?

    - by AlReece45
    Right now, we have a rack of servers. Every server right now has at least 2 IP addresses, one for the public interface, another for the private. The servers that have SSL websites on them have more IP addresses. We also have virtual servers, that are configured similarly. Private Network The private range is currently just used for backups and monitoring. Its a gigabit port, the interface usage does not usually get very high. There are other technologies we're considering using that would use this port: iSCSI (implementations usually recommends dedicating an interface to it, which would be yet another IP network), VPN to get access to the private range (something I'd rather avoid) dedicated database servers LDAP centralized configuration (like puppet) centralized logging We don't have any private addresses in our DNS records (only public addresses). For our servers to utilize the correct IP address for the right interface (and not hard code the IP address) probably requires setting up a private DNS server (So now we add 2 different dns entries to 2 different systems). Public Network Our public range has a variety of services include web, email, and ftp. There is a hardware firewall between our network and the "public" network. We have (relatively secure) method to instruct the firewall to open and close administrative access (web interfaces, ssh, etc) for our current IP address. With either solution discussed, the host-based firewalls will be configured as well. The public network currently runs at a dedicated 20Mbps link. There are a couple of legacy servers with fast-ethernet ports, but they are scheduled for decommissioning. All of the other production boxes have at least 2 Gigabit Ethernet ports. The more traffic-heavy servers have 4-6 available (none is using more than the 2 Gigabit ports right now). IPv6 I want to get an IPv6 prefix from our ISP. So at least every "server" has at least one IPv6 interface. We'll still need to keep the IPv4 addressees up and available for legacy clients (web servers and email at the very least). We have two IP networks right now. Adding the public IPv6 address would make it three. Just use IPv6? I'm thinking about just dumping the private IPv4 range and using the IPv6 range as the primary means of all communications. If an interface starts reaching its capacity, utilize the newly free interfaces to create a trunk. It has the advantage that if either the public or private traffic needs to exceed 1Gbps. The traffic for each interface is already analyzed on a regular basis to predict future bandwidth use. In the rare instances where bandwidth unexpected peaks: utilize QoS to ensure traffic (like our limited SSH access) is prioritized correctly so the problem can be corrected (if possible, our WAN is the bottleneck right now). It also has the advantage of not needing to make an entry for every private address. We may have private DNS (or just LDAP), but it'll be much more limited in scope with less entries to duplicate. Summary I'm trying to make this network as "simple" as possible. At the same time, I want to make sure its reliable, upgradeable, scalable, and (eventually) redundant. Having one IPv6 network, and a legacy IPv4 network seems to be the best solution to me. Regarding using assigned IPv6 addresses for both networks, sharing the available bandwidth on one (more trunked if needed): Are there any technical disadvantages (limitations, buffers, scalability)? Are there any other security considerations (asides from firewalls mentioned above) to consider? Are there regulations or other security requirements (like PCI-DSS) that this doesn't meet? Is there typical software for setting up a Linux network that doesn't have IPv6 support yet? (logging, ldap, puppet) Some other thing I didn't consider?

    Read the article

  • phpMyAdmin setup issues

    - by EquinoX
    I am trying to follow the tutorial here to setup the user and pass. It says there that "this section is only applicable if your MySQL server is running with --skip-show-database". First question is, how do I check if MySQl server is running with --skip-show-database? Is there any way I can access phpMyAdmin SQL query window without logging in? Otherwise I'd have to execute this SQL from command line. I am also getting this: Cannot load mcrypt extension. Please check your PHP configuration. I have added mcrypt.so to php.ini and doing the following command proves that I have it. [root@DT html]# rpm -qa | grep mcrypt mcrypt-2.6.8-1.el5 php-mcrypt-5.3.5-1.1.w5 libmcrypt-2.5.8-4.el5.centos [root@DT html]# php -v PHP 5.3.5 (cli) (built: Feb 19 2011 13:10:09) Copyright (c) 1997-2010 The PHP Group Zend Engine v2.3.0, Copyright (c) 1998-2010 Zend Technologies Now when I go to phpinfo() and search for mcrypt it can find it inside the Configure Command row ('--with-mcrypt=shared,/usr'). So, what to do next?. UPDATE: I didn't put extension=mcrypt.so in php.ini as it will complain the following: PHP Warning: Module 'mcrypt' already loaded in Unknown on line 0 Here's my nginx.conf: #user nobody; worker_processes 2; #error_log logs/error.log; #error_log logs/error.log notice; #error_log logs/error.log info; #pid logs/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; #log_format main '$remote_addr - $remote_user [$time_local] "$request" ' # '$status $body_bytes_sent "$http_referer" ' # '"$http_user_agent" "$http_x_forwarded_for"'; #access_log logs/access.log main; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; gzip on; server { listen 80; root /usr/share/nginx/html; server_name localhost; #charset koi8-r; #access_log logs/host.access.log main; location / { #root html; index index.html index.htm; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # error_page 500 502 503 504 /50x.html; location = /50x.html { #root html; } # proxy the PHP scripts to Apache listening on 127.0.0.1:80 # #location ~ \.php$ { # proxy_pass http://127.0.0.1; #} # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { #root /usr/local/nginx/html; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /usr/share/nginx/html$fastcgi_script _name; include fastcgi_params; } # deny access to .htaccess files, if Apache's document root # concurs with nginx's one location ~ /\.ht { deny all; } } # another virtual host using mix of IP-, name-, and port-based configuration # #server { # listen 8000; # listen somename:8080; # server_name somename alias another.alias; # location / { # root html; # index index.html index.htm; # } #} # HTTPS server # #server { # listen 443; # server_name localhost; # ssl on; # ssl_certificate cert.pem; # ssl_certificate_key cert.key; # ssl_session_timeout 5m; # ssl_protocols SSLv2 SSLv3 TLSv1; # ssl_ciphers ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP; # ssl_prefer_server_ciphers on; # location / { # root html; # index index.html index.htm; # } #} }

    Read the article

  • Make exact mp4 (H264) format for uploading to youtube

    - by WHITECOLOR
    With ffmpeg I'm converting video from mp3 and picture to upload it to youtube. After upload, conversion fails. Reasons are unknown. I believe the problem is in format. By the way If I'm uploading file 5 minutes length, it fails if I upload 30 seconds of this file it succeeds. I have donwload mp4 file from youtube. Then I uploaded it, it is done very fast. So a nice solution would be to convert videos to the same format that is done by google. I got the following output by mpeg: ffmpeg version N-44264-g070b0e1 Copyright (c) 2000-2012 the FFmpeg developers built on Sep 7 2012 17:38:57 with gcc 4.7.1 (GCC) configuration: --enable-gpl --enable-version3 --disable-pthreads --enable-runt ime-cpudetect --enable-avisynth --enable-bzlib --enable-frei0r --enable-libass - -enable-libcelt --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-l ibfreetype --enable-libgsm --enable-libmp3lame --enable-libnut --enable-libopenj peg --enable-librtmp --enable-libschroedinger --enable-libspeex --enable-libtheo ra --enable-libutvideo --enable-libvo-aacenc --enable-libvo-amrwbenc --enable-li bvorbis --enable-libvpx --enable-libx264 --enable-libxavs --enable-libxvid --ena ble-zlib libavutil 51. 72.100 / 51. 72.100 libavcodec 54. 55.100 / 54. 55.100 libavformat 54. 25.105 / 54. 25.105 libavdevice 54. 2.100 / 54. 2.100 libavfilter 3. 16.100 / 3. 16.100 libswscale 2. 1.101 / 2. 1.101 libswresample 0. 15.100 / 0. 15.100 libpostproc 52. 0.100 / 52. 0.100 Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'youtubetrack0.mp4': Metadata: major_brand : mp42 minor_version : 0 compatible_brands: isommp42 creation_time : 2012-10-02 22:58:57 Duration: 00:06:46.66, start: 0.000000, bitrate: 176 kb/s Stream #0:0(und): Video: h264 (Constrained Baseline) (avc1 / 0x31637661), yu v420p, 450x360, 78 kb/s, 6 fps, 6 tbr, 12 tbn, 12 tbc Metadata: creation_time : 1970-01-01 00:00:00 handler_name : VideoHandler Stream #0:1(und): Audio: aac (mp4a / 0x6134706D), 44100 Hz, stereo, s16, 95 kb/s Metadata: creation_time : 2012-10-02 22:58:57 handler_name : IsoMedia File Produced by Google, 5-11-2011 Is it possible to construct ffmpeg parameters so that that would give the same format that google internally does? Is the information above sufficient? I couldn't construct needed params. For example I don't understand how to set tbn and what 95 kb/s mean in "Stream #0:1(und): Audio:". Now I just do: ffmpeg -i videoimage.jpg -i audio.mp3 video.mp4 Info I've got: ffmpeg version N-44998-gdf82454 Copyright (c) 2000-2012 the FFmpeg developers built on Oct 2 2012 23:03:12 with gcc 4.7.1 (GCC) configuration: --disable-static --enable-shared --enable-gpl --enable-version3 --disable-pthreads --enable-runtime-cpudetect --enable-avisynth --enable-bzlib --enable-frei0r --enable-libass --enable-libcelt --enable-libopencore-amrnb --en able-libopencore-amrwb --enable-libfreetype --enable-libgsm --enable-libmp3lame --enable-libnut --enable-libopenjpeg --enable-librtmp --enable-libschroedinger - -enable-libspeex --enable-libtheora --enable-libutvideo --enable-libvo-aacenc -- enable-libvo-amrwbenc --enable-libvorbis --enable-libvpx --enable-libx264 --enab le-libxavs --enable-libxvid --enable-zlib libavutil 51. 73.101 / 51. 73.101 libavcodec 54. 63.100 / 54. 63.100 libavformat 54. 29.105 / 54. 29.105 libavdevice 54. 3.100 / 54. 3.100 libavfilter 3. 19.102 / 3. 19.102 libswscale 2. 1.101 / 2. 1.101 libswresample 0. 16.100 / 0. 16.100 libpostproc 52. 1.100 / 52. 1.100 Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'video.mp4': Metadata: major_brand : isom minor_version : 512 compatible_brands: isomiso2avc1mp41 encoder : Lavf54.25.105 Duration: 00:06:46.81, start: 0.000000, bitrate: 129 kb/s Stream #0:0(und): Video: h264 (High) (avc1 / 0x31637661), yuvj420p, 450x360, 3392 kb/s, 25 fps, 25 tbr, 25 tbn, 50 tbc Metadata: handler_name : VideoHandler Stream #0:1(und): Audio: aac (mp4a / 0x6134706D), 44100 Hz, stereo, s16, 127 kb/s Metadata: handler_name : SoundHandler This video fails the conversion on youtube. I also tried to use other vcode parmam and extensions of output file (mp4, wmv, avi) but failed too. Would be greatful for help.

    Read the article

  • What seems to be plaguing my hard drives?

    - by Craig
    In a little bit of a tech nightmare here. I know oodles about software, not so much more than the above average user about hardware. I recently had to toss an old desktop of mine. It was gradually getting slower and slower, and after shutting the desktop down for long periods of time, it would choke up upon startup. Sometimes it'd give a disk read error, sometimes say no OS was found, etc. Restarting it about 5-15 times would eventually boot properly. Weird. I also noticed that startup programs were going missing, Dropbox was reindexing my entire folder, and Backblaze was backing up less than the number of files that it should. This lead me to believe it was probably a hard drive issue. I began to wonder why I'd have hard drive issues, and came to closure when I assumed it was because of recent power surges and outages. I'm sure that does a number on the drive. I bought a new desktop recently. It's not a beast or anything, but it's enough for what I do. It's an eMachines (I know, I know) Ultra-Slim (http://www.amazon.com/eMachines-Ultra-Slim-ER1401-57-Desktop-PC/dp/B00475OG9U). This is ideal for me because it's small and portable. It comes with an AC adapter and battery, like a laptop. Just to be safe, I bought an uninterruptable power supply on top of that. It's basically protected completely from any outages that might scramble the drive. I set this up a few days ago and for the past few days I've been perfecting settings, downloading the usual applications, etc. Two days ago, I noticed Dropbox was reindexing my entire Dropbox folder. I installed both Dropbox and Backblaze on this system, but it is very much more lightweight than the other. Only about 15 third-party applications installed. I thought that maybe Dropbox and Backblaze were stressing my system, so I turned off Backblaze. Still, Dropbox runs and comes across this infinite reindex issue. I noticed that upon a reboot recently, two applications did not start on startup either. Also, much like my old desktop, every 3rd or 4th reboot, I'll be forced into a chkdsk. This makes me incredibly nervous. What could possibly be going wrong with my old, years-old desktop that is immediately causing the same issues to my new one? I've considered all of the basics. I'm in a very air conditioned room. I take run routine virus scans. I'd like to think I take care of my systems very well. What is this issue that is haunting me? There's always the possibility that this new desktop has a junk hard drive, but it just seems way too coincidental.

    Read the article

  • Weird Apache Access Logs

    - by user38480
    I see repeated requests like these in my Apache Access Logs and they have been eating up all my CPU. I have a normal WordPress installation. All i changed in the Apache Configuration was changing the DocumentRoot from /var/www/html to /var/www for both ssl and the default configuration. Also, the file referenced in the requests(updatedll.jpeg) does not exist on my server and also isn't referenced in the source code served by any page of the web application. Could this be a security threat? What are these actually and what can i do to stop them. I changed the ip address of my server. They still kept coming. Meaning that somebody is actually hitting the domain name and not the ip address. Why does my server send a 301 for these requests? Shouldn't it be sending a 404? Is it because Wordpress is installed in my root directory and the .htaccess file present for Wordpress is sending a 301 redirect? My disk access logs also seem to have high peaks intermittently. But nobody is actually accessing the site. I see no access logs except these below. Also, i see that all the requests seem to be coming from one of the following 5 ip addresses. 201.4.132.43 - - [05/Jun/2014:07:35:08 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; WOW64; Trident/4.0; BTRS103681; GTB7.5; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; InfoPath.2; OfficeLiveConnector.1.3; OfficeLivePatch.0.0; AskTbATU3/5.15.29.67612; BRI/2)" 187.40.241.48 - - [05/Jun/2014:07:35:08 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; Trident/4.0; GTB7.5; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729)" 186.56.134.132 - - [05/Jun/2014:07:35:10 -0400] "GET /updatedll.jpg HTTP/1.0" 301 428 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1; .NET CLR 1.1.4322)" 71.223.252.14 - - [05/Jun/2014:07:35:13 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; Trident/4.0; BTRS31756; GTB7.5; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729; .NET4.0C; .NET4.0E; InfoPath.2)" 85.245.229.167 - - [05/Jun/2014:07:35:14 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; Trident/7.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; MAAU; .NET4.0C; BRI/2; .NET4.0E; MAAU)"

    Read the article

  • 1600+ 'postfix-queue' processes - OK to have this many?

    - by atomicguava
    I have a Plesk 9.5.4 CentOS server running Postfix. I had been having massive problems with the mailq being full of 'double-bounce' email messages containing errors relating to 'Queue File Write Error', but I believe these are now fixed thanks to this thread. My new problem is that when I run top, I can see lots of processes called 'postfix-queue' and have fairly high load: top - 13:59:44 up 6 days, 21:14, 1 user, load average: 2.33, 2.19, 1.96 Tasks: 1743 total, 1 running, 1742 sleeping, 0 stopped, 0 zombie Cpu(s): 5.1%us, 8.8%sy, 0.0%ni, 85.3%id, 0.8%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3145728k total, 1950640k used, 1195088k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1324 apache 16 0 344m 33m 5664 S 21.7 1.1 0:03.17 httpd 32443 apache 15 0 350m 36m 6864 S 14.4 1.2 0:13.83 httpd 1678 root 15 0 13948 2568 952 R 2.0 0.1 0:00.37 top 1890 mysql 15 0 689m 318m 7600 S 1.0 10.4 219:45.23 mysqld 1394 apache 15 0 352m 41m 5972 S 0.7 1.3 0:03.91 httpd 1369 apache 15 0 344m 33m 5444 S 0.3 1.1 0:02.03 httpd 1592 apache 15 0 349m 37m 5912 S 0.3 1.2 0:02.52 httpd 1633 apache 15 0 336m 20m 1828 S 0.3 0.7 0:00.01 httpd 1952 root 19 0 335m 28m 10m S 0.3 0.9 1:35.41 httpd 1 root 15 0 10304 732 612 S 0.0 0.0 0:04.41 init 1034 mhandler 15 0 11520 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1036 mhandler 15 0 11516 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1041 mhandler 17 0 11516 1156 884 S 0.0 0.0 0:00.00 postfix-queue 1043 mhandler 15 0 11512 1116 860 S 0.0 0.0 0:00.00 postfix-queue 1063 mhandler 16 0 11516 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1068 mhandler 15 0 11516 1128 860 S 0.0 0.0 0:00.00 postfix-queue 1071 mhandler 17 0 11512 1152 884 S 0.0 0.0 0:00.00 postfix-queue 1072 mhandler 15 0 11512 1116 860 S 0.0 0.0 0:00.00 postfix-queue 1081 mhandler 16 0 11516 1156 884 S 0.0 0.0 0:00.00 postfix-queue 1082 mhandler 15 0 11512 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1089 popuser 15 0 33892 1972 1200 S 0.0 0.1 0:00.02 pop3d 1116 mhandler 16 0 11516 1164 884 S 0.0 0.0 0:00.00 postfix-queue 1117 mhandler 15 0 11516 1124 860 S 0.0 0.0 0:00.00 postfix-queue 1120 mhandler 16 0 11516 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1121 mhandler 15 0 11512 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1130 mhandler 17 0 11516 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1131 mhandler 15 0 11516 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1149 root 17 -4 12572 680 356 S 0.0 0.0 0:00.00 udevd 1181 mhandler 16 0 11516 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1183 mhandler 15 0 11512 1116 860 S 0.0 0.0 0:00.00 postfix-queue 1224 mhandler 16 0 11516 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1225 mhandler 15 0 11516 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1228 apache 15 0 345m 34m 5472 S 0.0 1.1 0:04.64 httpd 1241 mhandler 16 0 11516 1156 884 S 0.0 0.0 0:00.00 postfix-queue 1242 mhandler 15 0 11512 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1251 mhandler 17 0 11516 1156 884 S 0.0 0.0 0:00.00 postfix-queue 1252 mhandler 15 0 11516 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1258 apache 15 0 349m 37m 5444 S 0.0 1.2 0:01.28 httpd When I run ps -Al | grep -c postfix-queue it returns 1618! My question is this: is this normal or is there something else going wrong with Postfix? Right now, if I run mailq it is empty, and qshape deferred / qshape active are empty too. Thanks in advance for your help.

    Read the article

  • Log transport and aggregation at scale

    - by markdrayton
    How're you analysing log files from UNIX/Linux machines? We run several hundred servers which all generate their own log files, either directly or through syslog. I'm looking for a decent solution to aggregate these and pick out important events. This problem breaks down into 3 components: 1) Message transport The classic way is to use syslog to log messages to a remote host. This works fine for applications that log into syslog but less useful for apps that write to a local file. Solutions for this might include having the application log into a FIFO connected to a program to send the message using syslog, or by writing something that will grep the local files and send the output to the central syslog host. However, if we go to the trouble of writing tools to get messages into syslog would we be better replacing the whole lot with something like Facebook's Scribe which offers more flexibility and reliability than syslog? 2) Message aggregation Log entries seem to fall into one of two types: per-host and per-service. Per-host messages are those which occur on one machine; think disk failures or suspicious logins. Per-service messages occur on most or all of the hosts running a service. For instance, we want to know when Apache finds an SSI error but we don't want the same error from 100 machines. In all cases we only want to see one of each type of message: we don't want 10 messages saying the same disk has failed, and we don't want a message each time a broken SSI is hit. One approach to solving this is to aggregate multiple messages of the same type into one on each host, send the messages to a central server and then aggregate messages of the same kind into one overall event. SER can do this but it's awkward to use. Even after a couple of days of fiddling I had only rudimentary aggregations working and had to constantly look up the logic SER uses to correlate events. It's powerful but tricky stuff: I need something which my colleagues can pick up and use in the shortest possible time. SER rules don't meet that requirement. 3) Generating alerts How do we tell our admins when something interesting happens? Mail the group inbox? Inject into Nagios? So, how're you solving this problem? I don't expect an answer on a plate; I can work out the details myself but some high-level discussion on what is surely a common problem would be great. At the moment we're using a mishmash of cron jobs, syslog and who knows what else to find events. This isn't extensible, maintainable or flexible and as such we miss a lot of stuff we shouldn't. Updated: we're already using Nagios for monitoring which is great for detected down hosts/testing services/etc but less useful for scraping log files. I know there are log plugins for Nagios but I'm interested in something more scalable and hierarchical than per-host alerts.

    Read the article

  • My PC suddenly doesn't detect the primary drive (SSD)

    - by smoth190
    My computer has been working fine for months, and it worked today, but tonight I went to start it up to find that my OCZ Vertex 2 isn't being found. When I turn on my computer, the loading screen gets stuck at "Detecting IDE drives...". After a while, it keeps going and lists the drives it finds. The first one in the list should be my Vertex 2, but it just says "None". The computer proceeds to get stuck on "Loading operating system...", which is understandable because the drive with the OS is "gone". My first thought was drive failure, but every time drives have crashed on me, they're still detected--they just don't work. This drive is an SSD, it's pretty new, and I had no problems beforehand. I find it hard to believe it failed. I'm sure it's possible, but I hope this isn't the case. There has been nothing strange going on at all with my PC, it's been running perfect until now. I was just about to do my monthly dskchk and defrag today. I popped in my Windows 7 Home Premium disk and booted from it. When I launched the repair tool, it didn't list any operating systems (because the drive is 100% missing...). When I've had disks crash before, it still listed the OS, you just couldn't do anything with it. I tried to restore from an image, but I don't have any of those, either. I opened the command console and listed the drivers with wmic logicaldisk get name. Only C: and D: came up. C: was my 1TB storage driver (luckily, all my stuff is here--only the OS is on the SSD!) and D: was the disk driver. So I still had an MIA drive... The SSD didn't come with any driver disks, so I can't install drivers. If there's a way to do this from a CD I can burn with my other PC, please let me know. What the heck do I do? Although only the OS is on my SSD, a new SSD is expensive. I'll probably also have to buy a new copy of Windows (an upgrade would be nice, though...) because I've found it eats my registration key when my PC crashes (and my thousands of dollars of Adobe programs, I'll be on the phone with tech support for a week to get those keys back). And I'll lose my registry, all my settings, all sorts of other stuff that I'll spend weeks restoring. My computer is a pain in the butt to take out and open up, so if I can't fix it, I'll try fiddling with the plug or putting it into a new computer, but not right now. Any help is greatly appreciated! The day when they make crash-less drives will be the day I live without worry.

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 533 534 535 536 537 538 539 540 541 542 543 544  | Next Page >