Search Results

Search found 34971 results on 1399 pages for 'st even'.

Page 538/1399 | < Previous Page | 534 535 536 537 538 539 540 541 542 543 544 545  | Next Page >

• Installing Windows XP sp3 into USB 2.0 WD 320Gb Hard Drive

  - by NetKabuki

  I have a HP laptop with support for 3 USB 2.0 ports. I also have a clean 320Gb WD USB 2.0 drive. The HP can boot from USB (Bios options). I used the install disk (XP SP3 bootable) and after a few stutters, was actually able to load up a partition on the 320Gb drive with Windows. I cannot consistently get the system to boot up off the USB drive. I am able to drop Ubuntu on that same WD drive and boot up. I can even get Grub2 on Ubuntu to recognize the Win OS. But booting the Win OS is an impossible task. What can I do differently - if anything?

  Read the article

• What version of SCO Open Server are guys using out there and on what hardware?

  - by Gath

  I have some old applications which are running on SCO Open Server 5.0.5, and i would love to move them to SCO Open Server 5.0.7 and on modern hardware(servers), currently am running SCO on old IBM PL 300 personal computer, on 92MB Memory, one processor, and it has been serving the clients pretty well. Now i have New Modern IBM xseries Servers and i would love to migrate the same applications to those new servers. Problem is, SCO 5.0.5 is unable to detect some of the hardware components in the new servers. I read somewhere that SCO 5.0.7 is able to detect the newer hardware even the USB ports etc. Is there anyone running SCO Openserver out there, and on what hardware architecture are they running on? Gath

  Read the article

• Unable to resolve hostname on a proxy network

  - by ali

  I can browse sites using firefox configured with proxy 172.1.6.0.6:3128 resolv.conf domain pudhcp.ac.in search pudhcp.ac.in nameserver 172.16.0.7 I checked with Windows and I found the same DNS server settings 127.0.0.1 bt 127.0.1.1 bt Above is the hosts file I modified the top line from localhost to bt still not working bt is the hostname Still I can't ping to google.com - it is showing unable to resolv hostname I tried all solutions,I guess proxy is used even for DNS resolution root@bt:~# dhclient There is already a pid file /var/run/dhclient.pid with pid 7157 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ Listening on LPF/eth1/5c:ac:4c:b1:0c:7c Sending on LPF/eth1/5c:ac:4c:b1:0c:7c Listening on LPF/eth0/60:eb:69:18:4d:3d Sending on LPF/eth0/60:eb:69:18:4d:3d Sending on Socket/fallback DHCPREQUEST of 172.16.6.87 on eth0 to 255.255.255.255 port 67 DHCPACK of 172.16.6.87 from 172.16.6.1 bound to 172.16.6.87 -- renewal in 79432 seconds.

  Read the article

• TCP/IP- what is it exactly?

  - by OckhamsRazor

  I know that this question sounds stupid, but over all these years, I still have difficulty explaining TCP/IP to people. I don't completely get it myself, and even after reading up on it, the distinction is not very clear. What I get so far is that IP deals with networks while TCP involves delivery of messages over that network. I'm not totally convinced though. Also, they reside on different layers of the Internet architecture. Could anyone disambiguate this distinction using a simple analogy or examples? Also, I read this somewhere The difference is that TCP is responsible for the data delivery of a packet and IP is responsible for the logical addressing. In other words, IP obtains the address and TCP guarantees delivery of data to that address. Is this correct? Thanks for helping me out. One last thing- Where does the ethernet come in all of this?

  Read the article

• Create Webmin user for an EC2 Instance

  - by Dean

  I've setup an Amazon EC2 Instance, using the Ubuntu 12.04 AMI (ubuntu/images/ebs/ubuntu-precise-12.04-amd64-server-20120424 (ami-a29943cb)), and I'd like to get Webmin working (so I can setup a DNS). After following the installation instructions on Webmin's site, the installer says I can login with any username/pass of a user who has superuser access. The problem is that the EC2 instance only has 1 user "ubuntu", which can only login using SSH keys -- not a password! I've tried creating users manually and I can't login as those users (even via SSH), so I think it might be a permission thing provided by the AMI. Does anyone know the best way around setting up a login to my webmin?

  Read the article

• Ubuntu Server 12.04 LTS on Hyper-V 2012

  - by user137533

  I have the following scenario: Hyper-V 2012 server core installation. On top of this i created a virtual machine on which i tried installing Ubuntu Server 12.04 which should not have any compatibility issues according to what Microsoft and Ubuntu are saying (although it is not officially supported). I start, run the installation and everything is ok, no problems detecting the network device or the hard drive (unlike debian which didn't even detect the hard drive). Once the installation is complete it asks me to reboot, it unmounts the "dvd drive" and reboots. Once it tries to start again i get the following error: Boot failure. Reboot and Select proper Boot device or Insert Boot Media in the selected Boot device. It seems to not be booting up from the virtual hard drive. The hard drive is set up in SCSI mode, nothing mounted on the IDE controller (no iso image or anything else. Does anyone have any ideas on what i can do to solve this?

  Read the article

• Wordpress site on EC2 instance suddenly superslow

  - by Emil

  Set up a wordpress page the other day following this guide. The site was up and running, loading quickly and all was well, until today. Suddenly, loading the site takes forever and doesn't even work properly, the page shows up in an incomplete fashion. I tried rebooting the instance but that didn't help. The only actions I've taken on the server is to create an elastic IP, and to point a domainname to that IP. But I don't see how that could've slowed down the page. Any thoughts on what could have caused this and on a solution to the problem?

  Read the article

• Authenticating Mountain Lion over Ubuntu 12 LDAP [closed]

  - by Sam Hammamy

  Possible Duplicate: Ubuntu OpenLDAP and Mac OS X Roaming Profiles I've installed slapd on Ubuntu 12 after a long long day of trial and error. I've added the apple.ldif schema, and the samba.ldif schema, plus a test user. Last week, I had installed slapd on Ubuntu 11, and was able to authenticate against it from OS X Lion after finding the following blog post: Fixing OpenLDAP Authentication on OS X Lion This suggests running the following commands to fix the authentication problem /usr/libexec/PlistBuddy -c "add ':module options:ldap:Denied SASL Methods:' string CRAM-MD5" /Library/Preferences/OpenDirectory/Configurations/LDAPv3/yourldapserver.plist /usr/libexec/PlistBuddy -c "add ':module options:ldap:Denied SASL Methods:' string NTLM" /Library/Preferences/OpenDirectory/Configurations/LDAPv3/yourldapserver.plist /usr/libexec/PlistBuddy -c "add ':module options:ldap:Denied SASL Methods:' string GSSAPI" /Library/Preferences/OpenDirectory/Configurations/LDAPv3/yourldapserver.plist However, I ran these commands on OS X Mountain Lion, and I am still unable to authenticate. I can't even use the Directory Editor app to examine the AD. I am however able to bind to the server via python-ldap's ldap.simple_bind_s('cn=admin,dc=foo,dc=net,'secret'). The error I am getting when trying to use Director Editor is Error Code (5000)

  Read the article

• Socksify TCP connections reaching a gateway IP -- preferably without iptables

  - by Alexandra Neagu

  I have Virtualbox installed on Debian with a few virtual machines. I can't install anything in the guests, and I use host only networking, vboxnet0. The host IP in the host network is 192.168.56.1, and the guests have static IPs in 192.168.56.0/24. I access Internet with a SOCKS proxy (without authentication) and I would like the Virtualbox guests TCP connections to be sent through the SOCKS proxy. This would also be useful for socksifying external TCP reaching a gateway network card or wireless access point. I looked at transocks, tun2socks, with dante-client, etc., but I don't know how can I achieve this without enabling IP forwarding in the host and using iptables. Maybe to attach somehow the Virtualbox vboxnet0 network to the tunnel tun0 used by tun2socks? Or maybe there is a way to do NAT to tun0 in Virtualbox? I only need TCP traffic and I don't need UDP, not even for DNS.

  Read the article

• How to get rid of InternetCorkboard.com virus (specifically)?

  - by ADSMarko

  The other day I picked up the new version of InternetCorkboard.com virus, the one that doesn't come with any program I've installed (as far as I can tell) and that doesn't show among Firefox add-ons. I've tried as much as I could google and even installed brand new version of Microsoft Security Essentials. I did the full scan with MSE and it didn't find anything. ATM I'm back at three-years old Firefox, but I wanna kick the bastard out. I got redirected here from Stack Overflow, but I need an answer since everything I could google is worse than useless. So anyone has any idea how to kick InternetCorkboard virus specifically?

  Read the article

• Flash Media Server 3.5 Installation Problem.

  - by prateeksaluja20

  Hello Experts, I installed Flash media server 3.5 in windows 7 home basic.it installed properly. When i try to open the media server,and not showing in its FMS ADMIN CONSOLE there. I have beeen checking the windows services, it shows flash media server is running.i have installed FMS in Default port (1935,1111).i have MCAFEE Antivirus.1st time it blocks the My FMs then i Allowed it & after that there is no issue.i am not getting what is the problem,is anything blocking the FMS.Even I am not able to start/see the control panel of FMS (Flash media server). I am guessing it is a port problem,Is it or any firewall issue?Please Suggest.

  Read the article

• Recovering OS X Mail Accounts Lost in Crash

  - by Tim

  I had a hard crash on my Mac PowerBook and when I restarted, Mail came up with only my MobileMe account still available and I cannot figure out how to restore the other eight email accounts I have. The directories in ~/Library/Mail all seem to be there. I even did an rsync of the modified .plist files from a TimeMachine backup of the directory from before the crash (unfortunately, I was on travel, so the backup is more than a week old and I'd like to try and recover from that point without having to entirely restore from TimeMachine). I also did a fix permissions. So my questions are where exactly is the account information for Mac Mail kept? Any thoughts of what might have caused the failure? Why does only MobileMe come up? Any other thoughts on how to fix things?

  Read the article

• Why no "da-doomp" (disconnect notification sound) sometimes when unplugging wireless mouse receiver?

  - by DanH

  Sometimes (maybe one case in 3), when I unplug the wireless mouse receiver on my Sony VGN-CS215J laptop, there is no "da-doomp" sound, even after a minute or two. And if I plug the receiver back in there is no corresponding "du-dump" sound and the mouse is still (immediately) "live". This can happen when the activity light is out and there's nothing obviously going on -- it's not simply that the box is too busy. Other times one gets the expected behavior (and usually I get the correct behavior if I plug the receiver back in a few seconds and then unplug it after a "failure"). The reason this is significant is that if I get no "da-doomp" then the laptop will not sleep properly -- it will go to sleep initially, but then reawaken a few minutes later inside my laptop case and proceed to run the battery down (and no doubt overheat the unit). Any ideas?

  Read the article

• NetBSD as VMware workstation guest: `startx` hangs and maxes all CPUs utilization

  - by Howard Guo

  I am using VMware workstation 8. I have attempted to install and run NetBSD 5.1.2 and 6.0. Installations all went OK and the system was usable until I install a window manager. After installed xfce4, in NetBSD 5.1.2, I could startx and used xfce4 two times, however consecutive startx will hang and max all CPU to 100%. In NetBSD 6.0 RC2, I could not even start xfce4 once, startx hangs and max all CPU to 100%. I have tried to use both vmwlegacy and vmware device drivers, they don't help. I have also tried both 32bit and 64bit NetBSD, they behave in the same way. I also tried to catch the output of startx, however system was already hanging before the output gets flushed. Apparently no one else has encountered these troubles on Google search, did I miss any configuration piece? Any other suggestions please?

  Read the article

• Unable to setup ssh tunnel on mac

  - by prashant

  On my office windows XP laptop I use a program called Bitvise Tunnelier to establish ssh tunnel to a in-house MySQL database. In the Tunnelier program I also need to provide address of corporate http proxy server in order to establish tunnel. On my personal mac laptop, I use Cisco Anywhere client to establish a VPN connection to my corporate network. But i'm unable to establish ssh tunnel to mysql database using ssh. How do I specify the proxy server address in the ssh command? As additional info when i'm using office laptop (whether in home or office) I can successfully ping to the server address specified in the Tunnelier program. But i cannot ping the same server using my mac machine (even after connecting via VPN). So basically i'm unable to understand what's going on and what steps i can take to debug this problem .

  Read the article

• Can I completely remove the Windows DNS in favour of BIND9 in an AD network?

  - by Vinícius Ferrão

  I would like to remove the DNS feature of Windows Domain Controllers and point the DNS servers to our BIND9 servers. I know it's possible to setup coexistence but this requires a number of extra Windows DNS Servers equals to the number of Domain Controllers in the network. Active Directory expects the _msdcs zone and other things like _tcp, _udp; etc. The main question is: how to make BIND9 takes care of all this AD specific data? And with dynamic updating to make AD even more happier. Thanks, PS: Making BIND9 points to the Windows DNS Servers to resolve the Active Directory specific zones isn't an option. We already do this... EDIT: As today, I'm running without Windows DNS. I'm writing up a guide on how to do this, and I'll update this topic.

  Read the article

• Slow network file access with VMWare Server and Windows 7

  - by garethm

  I have Windows 7 32-bit virtual machine running in a VMWare Server virtual machine. The host is Windows 7 64-bit. When I copy files between them it is extremely slow - it will take several minutes to copy even a 1 MB file. I can upload the file to an website and then download it again almost instantaneously by comparison. Browsing the network is quite zippy and has no problems. I have been unable to set up a HomeGroup between the computers though - the guest always times out without managing to get setup. Any ideas on how I should go about tracking down where the problem is?

  Read the article

• OSX: Selecting default application for all unknown and different file types (extensions)

  - by Leo

  I work in cluster computing and am using Mac OS X 10.6. I send off hundreds of computing jobs a day, and each one comes back with with a different extension. For example, svmGeneSelect.o12345 which is the std output of my svmGeneSelect job which is job number 12345. I don't control the extensions. All files are plain text. I want OSX to open any file extension that it hasn't seen before with my favorite text editor when I click on it. Or even better set up file association defaults for extension patterns ie textEdit for extensions matching *.o*. I do NOT want to create file associations for individual files since this extension will only ever exist once, and I do not want to go through the process of selecting the application to use for each file. Thanks for any help you can offer.

  Read the article

• Windows 7 won't read from NAS on LAN

  - by Alfy

  I've got a Linkstation NAS drive on a local network. Having just got a new laptop with Windows 7 Home Professional, I can no longer read anything of the drive. I've tried accessing the drive using \192.168.1.55\share, using ftp programs such as WinSCP, filezilla and even using firefox to hit ftp://192.168.1.55. The really annoying thing is that through these methods I can see the files on the drive, counting out any kind of connection issues. I can navigate through the NAS file system, but as soon as I try and copy a file off the NAS, things just stop working. Accessing the drive through a Windows XP machine works fine. So far I've tried: Disabling firewalls Adding the LmCompatibilityLevel key to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Lsa Using the 40 - 56 bit encryption instead of the 128 bit. Has anyone got any suggestions of what I can check or try? This is driving me crazy and I'm totally out of ideas?

  Read the article

• Adaptec 2420SA RAID 1 rebuild 66% after 1 week

  - by moss

  We're running a 500GB RAID 1 on an Adaptec 2420SA - 2x500GB Hitachi Drives. It suddenly crashed and required a rebuild -- was not even booting. It's only at 66% after about a week. Very frustrated. This is the second box with the same card and drives that has had issues with the RAID/drives. Another box had this happen twice. Both machines are Linux boxes. CentOS and Fedora. I dunno if it's the firmware -- which currently needs an update (any help doing this over PXE would be great- I have used UDA to do PXE boots in the past). Anyway, would love to hear about experiences with this card and firmware. I thinking of going google and just using cheap boxes no raid and have server redundancy instead.

  Read the article

• Is it possible to stream input into RAR

  - by Dscoduc

  I'm using RARLABS RAR.exe to archive/backup my server data. I am familiar with using RAR for creating an archive and adding files from a folder, but what about streaming data directly into an archive? For example, when backing up my MySQL databases I use the mysqldump command that includes a pipe command into a text file. It would be nice to skip the file step and go directly into an archive file using something like the following syntax: mysqldump -uUserName -pPassword --all-databases > rar.exe newarchivename.rar Does anyone know if what I have described, or something similar, is even possible?

  Read the article

• Why would the IIS UrlRewrite module continue redirecting requests after the rule is removed?

  - by Jon Norton

  Our application uses the IIS UrlRewrite module to temporarily redirect requests during upgrades to a maintenance site. We have seen a few instances where even though the redirect rule has been removed, the server continues to redirect all requests according to the removed rule. There does not seem to be any pattern with this, and has only occurred once or twice. We have taken the following steps to try and determine the cause of this behavior. Verified that the original rule was a 307 temporary redirect Requested the application from machines that had never requested it before Used a different browser Added and removed a dummy rule from the IIS management console Checked the http kernel cache using netsh http show cachestate Modified the applicationHost.config file by hand (the rule was not still in the file, we just added a superfluous space) In the past when this has happened, we have been able to restart IIS and it solves the problem but that is not always an option and we really want to figure out what the root cause is. How or why would UrlRewrite be caching the response and not responding to configuration changes?

  Read the article

• Trying to mount NFS share on Windows Machien at startup with Z: letter for all users

  - by ScottC

  Windows Server 2008 We are trying to mount a specific drive letter on a windows machine from a unix machine. We need the mount to be available to the server even if no users are logged in and to users who are logged in with If we run the command from the command prompt manually it conencts and we have access to the NFS share, and can open it and see and edit files. mount -o fileaccess=777 anon \\127.0.0.1\nav z: (ip address replaced with 127.0.0.1 for security reasons) However if we try to automate the task by making an entry in the task schedule for boot time, to execute the batch script, it adds a disconencted drive to the list in 'My Computer' but it is disconencted and when trying to access the drive an error is produced: Z: is not accessible The data area passed to a system call is too small.| Tried as administrator with highest privelidges, as SYSTEM (group) and as my user (adminstator level user) same results. Is there another way to do this? Most of the help I have found online suggest this way but it keeps failing.

  Read the article

• Minidump folder cannot be found

  - by Saxtus

  Although I have enabled the creation of minidump files in my system, it appears that either Windows doesn't create them where the Startup and recovery dialog points to (%SystemRoot%\Minidump) or at least I can't find them. Even the Minidump folder under Windows directory is missing and I had numerous BSODs till now. I've searched all my HDs for mini*.dmp files only to find some old ones in a backup folder from my Vista x86 installation, before I install Windows 7 x64. Any thoughts of why this is happening and how to fix it? Pre-thanx!

  Read the article

• What is the simplest way to build your own .deb package?

  - by Calvin Fisher

  Having used Ubuntu for several years now, I've assembled a short list of scripts and packages that I always install on my computers. I would like to pack them up into a .deb to make it easier to get set up on a fresh OS installation. I'm imagining, for instance, one package that would install all of my custom BASH scripts that I've made for common tasks, and another one that would depend on other packages (like w64codecs) that I always install but forget that I need to until I go to do something and it's not there. It doesn't even have to be by-the-book; I'm not looking to deploy these publicly. I'm just looking to roll up all these tasks into one sudo dpkg --install. To quantify "simple" or "easy," I mean to say that I'm looking for the method with the fewest steps requiring the least technical knowledge and, most importantly, taking the least time.

  Read the article

< Previous Page | 534 535 536 537 538 539 540 541 542 543 544 545  | Next Page >