Search Results

Search found 18191 results on 728 pages for 'single board'.

Page 542/728 | < Previous Page | 538 539 540 541 542 543 544 545 546 547 548 549  | Next Page >

• SCM8014 to FVS338

  - by Jack

  I have a SMC8014 Router/Modem that Comcast provided me with their business class service. It was not filtering malicious traffic as aggressively as I had hoped, so I purchased a NetGear ProSafe FVS338, and put this behind the SMC8014, and all my machines behind that. After some brief configuration, all machines can see out to the internet. I also have a single web server, and I have not been able to configure things so that incoming requests can reach it. This is where I need help! I would like to have the FVS339 do NAT, so that I can assign a 192.168 address to my webserver. I've tried everything I know of, and I can't get things going. I set the SMC8014 to have a LAN facing IP of 10.0.0.1, and I assigned the FVS339 a WAN facing IP of 10.0.0.2. I would like to be able to tell the SMC8014 to just forward all traffic to 10.0.0.2, but I haven't had any success. In my (unfortunately limited) understanding, what I probably want here is a static route, but I don't know how to cofigure one, or if this is really what I want. The SMC8014 wants a Destination IP, a Subnet Mask and a Gateway IP. Any help would be appreciated.

  Read the article

• Struggling to set-up NLB cluster

  - by Chris W

  I'm trying to set up NLB on a couple of Windows 2008 R2 virtual servers running on top of Hyper V R2. The servers each have a single vNIC for LAN access (and a second vNIC for SAN access). I'm setting up the cluster to use Multicast mode. The vNICs are each set to allow MAC spoofing. Essentially I'm finding that i can add SERVER1 as a host and it will pick up and respond to the cluster IP from a remote subnet. If I then 'stop' the node in NLB manager it still responds when I would expect it to stop answering on that IP. If I recreate the cluster and add SERVER2 as the first host, the wizard completes correctly and an IPCONFIG on the server shows that it now has the cluster IP but I can't ping the cluster IP from a remote subnet but I can from another machine on the same subnet. As a final test - with both servers in the cluster, pinging from another machine on the same subnet I still get a response from the cluster IP when both nodes are stopped according to the NLB manager. The two VMs are sat on the same physical blade and are built up exactly the same as they'll be used as SharePoint web front end servers. I'm at a loss as to what could be wrong with the second VM that prevents it taking on the address just as the sole node in the cluster, never mind the strange behaviour of the cluster when I stop/start nodes.

  Read the article

• Kernel Logging disabled?

  - by Tiffany Walker

  uname -a Linux host 2.6.32-279.9.1.el6.i686 #1 SMP Tue Sep 25 20:26:47 UTC 2012 i686 i686 i386 GNU/Linux And start ups: ls /etc/init.d/ abrt-ccpp certmonger dovecot irqbalance matahari-broker mdmonitor nfs proftpd rpcbind single ypbind abrtd cgconfig functions kdump matahari-host messagebus nfslock psacct rpcgssd smartd abrt-oops cgred haldaemon killall matahari-network mysqld ntpd qpidd rpcidmapd sshd acpid cpuspeed halt ktune matahari-rpc named ntpdate quota_nld rpcsvcgssd sssd atd crond httpd lfd ma tahari-service netconsole oddjobd rdisc rsyslog sysstat auditd csf ip6tables lvm2-lvmetad matahari-sysconfig netfs portreserve restorecond sandbox tuned autofs cups iptables lvm2-monitor matahari-sysconfig-console network postfix rngd saslauthd udev-post But when I installed CSF/LFD I am getting nothing. LFD does not create lfd.log and nor are any blocks being logged in /var/log/messages either from the firewall. This is not natural. I looked for klogd but maybe I am looking in the wrong place for it to see if it is enabled? ls /etc/init.d/syslog ls: cannot access /etc/init.d/syslog: No such file or directory Also noticed no syslog? Also noticed this: csf -d 84.113.21.201 Adding 84.113.21.201 to csf.deny and iptables DROP... iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. I've never seen this before and this is a dedicated box. Also: ./csftest.pl Testing ip_tables/iptable_filter...OK Testing ipt_LOG...OK Testing ipt_multiport/xt_multiport...OK Testing ipt_REJECT...OK Testing ipt_state/xt_state...OK Testing ipt_limit/xt_limit...OK Testing ipt_recent...OK Testing xt_connlimit...OK Testing ipt_owner/xt_owner...OK Testing iptable_nat/ipt_REDIRECT...OK Testing iptable_nat/ipt_DNAT...OK RESULT: csf should function on this server iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination

  Read the article

• How to tell which process is hogging my CPU when they don't add up to 100%?

  - by endolith

  Ubuntu's System Monitor applet shows 100% CPU usage continuously. If I click it, the resources tab shows it at 100% continuously, too. If I go to processes, though, to find out which process is the culprit, there is nothing above 10%. If I run top there is nothing above 10%. The individual processes do not add up to 100%. I try killing lots of processes, but the overall usage continues to be 100%. How can I find out what's hogging the CPU? This is an unusual situation on a computer I use daily, which is never anywhere near 100% CPU unless I'm doing something that requires it (like loading 32 Firefox tabs), after which it goes back to a normal idle level. It's not a new install or anything. There is no reason the processor should be maxed out. I'm not sure when it started or if I changed something that caused it to happen. Normally I would use top or System Monitor and find the process that had gone out of control, but I can't find anything with those tools this time. It persists after reboots and everything. And the processor is obviously hot, so it's not an erroneous reading. Update: I tried killing every process, one at a time, until the problem went away, and killing vino-server finally fixed it, even though that process never went above 5%. I had enabled Remote Desktop a few days ago (and have obviously now disabled it). But the question remains: How did a single process manage to use 100% CPU while top only showed that process at 5%? How do I identify culprits like this in the future? Looks like I'm not the only one who's had this problem: Still a problem in both jaunty & karmic. Interestingly, both System Monitor & htop do not show the sum of individual processes being anywhere near 100% cpu.

  Read the article

• Apache Process question about RAM usage

  - by Andrew Fashion

  So everytime I load a new page, I notice a new HTTPD process opens, every time I click a page, and each process says it's using anywhere from 2-4.5% of memory. Does that mean every single process is running at that time using 2-4% of RAM? It's a brand new server and I'm the only one on the server at the moment. Or does it mean all the other processes are dying, and only the new one is active. Because 4% of my 2048MB of RAM is already 82MB for just one process!?!? Let me know, because I am trying to determine what I need to beef my server up in order to handle high loads of traffic. I'm expect to get 20,000 uniques per day on launch. I am currently running a Dual Quad Xeon server, with only 2GB of ram, I will upgrade to 8GB or more shortly. Let me know what you suggest! thank you [root@D18634 log]# top | grep 'httpd' 11315 apache 15 0 362m 82m 24m R 12.3 4.1 0:03.00 httpd 11310 apache 16 0 322m 41m 21m S 5.7 2.1 0:02.98 httpd 11315 apache 15 0 362m 83m 25m S 24.3 4.1 0:03.73 httpd 11319 apache 16 0 324m 42m 20m R 1.0 2.1 0:01.85 httpd 11319 apache 16 0 362m 82m 23m R 78.5 4.1 0:04.21 httpd 11321 apache 16 0 323m 44m 23m S 35.3 2.2 0:04.13 httpd 11319 apache 15 0 361m 82m 23m S 8.3 4.1 0:04.46 httpd 11321 apache 15 0 323m 44m 23m S 35.9 2.2 0:05.21 httpd 11313 apache 15 0 324m 41m 19m S 48.6 2.1 0:03.23 httpd 11322 apache 16 0 354m 72m 20m R 11.0 3.6 0:05.11 httpd 11322 apache 16 0 354m 72m 20m S 23.9 3.6 0:05.83 httpd 11314 apache 16 0 355m 75m 22m R 18.3 3.7 0:04.64 httpd

  Read the article

• Adobe Acrobat Reader don't zoom out the page enough in "one page" mode

  - by mbaitoff

  I'm using Adobe Acrobat Reader version 9.4 under Debian Lenny. I'm experiencing a problem: when I push the "Show one page at a time" button, I expect the page to zoom such that pressing PgUp/PgDn would turn to the next/previous page. However, the zoom seems to be not enough - very thin bottom portion of the page doesn't fit inside the reader window, and pressing PgUp/PgDn gives the jitter of the same page, and I have to push twice to get to the next page. It is even worse in continuous page mode - a roll of pages begin to be non-synced with window boundaries, ending up with page break right in the middle of the view after several turns of the pages. This behaviour doesn't occur on windows version - I have a page properly zoomed in single/continuous modes, so that turning the pages is performed as page-at-once, as intended. How to make the Acrobat Reader fit the page to window properly? Thats how it looks before pressing PgDn (notice the bottom edge of the "paper" hidden beneath the bottom window edge): Thats how it looks after pressing PgDn (notice the "paper" bottom edge emerged from beneath the window edge, while the "paper" upper edge hides behind the upper window edge, showing that the document window size is not enough to contain the whole page):

  Read the article

• Remote assistance from Remote Desktop sessions: unable to control

  - by syneticon-dj

  Since Remote Control (aka Session Shadowing) is gone for good in Server 2012 Remote Desktop Session hosts, I am looking for a replacement to support users in a cross-domain environment. Since Remote Assistance is supposed to work for Remote Desktop Sessions as well, I tried leveraging that for support purposes by enabling unsolicited remote assistance for all Remote Desktop Session Hosts via Group Policy. All seems to be working well except that the "expert" seems to be unable to actually excercise any mouse or keyboard control when the remote assistance session has been initiated from a Remote Desktop session itself. Mouse clicks and keyboard strokes from the "expert" session (Server 2012) seem to simply be ignored even after the assisted user has acknowledged the request for control. I would like to see this working through RD sessions for the support staff due to a number of reasons: not every support agent would have the appropriate client system version to support users on a specific terminal server (e.g. an agent might have a Windows Vista or Windows 7 station and thus be unable to offer assistance to users on Server 2012 RDSHs) a support agent would not necessarily have a station which is a member of the specific destination domain (mainly due to the reason that more than a single domain's users are supported) what am I missing?

  Read the article

• SQL server agent job to execute SSIS package fails, package succeds if run manually

  - by growse

  I've got a SSIS package installed on a SQL server (SQL Server 2012). It's fairly simple and just fetches data from a remote data source and adds it into a local table. The remote connection string is using SQL server authentication, while the local connection is using Windows auth. The remote connection password is protected, and the package was imported setting the protection level to Rely on server storage and roles for access control. If I run the SSIS package manually, it works. If I run it from the command line using dtexec, it works. If I use runas to switch to the domain account that the SQL server agent is running under, and then run the package using dtexec, it works. If I create a SQL Agent job with a single step to run the package, it fails, providing very little detail as to what's going on. I'm guessing it's not able to get the password to log into the remote SQL server, because it fails very quickly. Also, if I tick 'log to table' and view the resulting file, I get the following: Description: ADO NET Source has failed to acquire the connection {0D8F2CD4-A763-4AEB-8B52-B8FAE0621ED3} with the following error message: "Login failed for user 'username'.". If I try to add the password in the connection string manually under data sources in the job step dialog, it refuses to save it, always seeming to remove the 'password' bit of the connection string. I thought that SQL server agent jobs always ran under the context of the account which the SQL server agent is running under. This account is a sysadmin on the local SQL server, and the package works using dtexec under that account, so why would it fail when trying to run as an agent job?

  Read the article

• Password-protected sharing allows access to users who have no account?

  - by romkyns

  Running Win7 on two computers in my LAN. Computer A has password-protected sharing enabled, and shares a folder. It has a single user account "Bob", and the Guest account is turned off. The network is workgroup-based. According to the descriptions of the "password-protected sharing" I could find, the only people who can access the shared folder via the LAN are those who know the username+password for the "Bob" account. However a second computer on the LAN is able to view this shared folder by simply browsing to Computer A. They don't need to enter any passwords or anything. The only user account registered on that PC is called "Jim", and has a different password from "Bob". How on earth is computer B able to view this shared folder? Is the popular description of the "password-protected sharing" feature inaccurate / did I misunderstand it big time? P.S. There is a possibility that the password for "Bob" has been entered on that PC once, and possibly the "remember password" box was checked. I've looked in the "Credential Manager" on both computers and there is nothing saved anywhere.

  Read the article

• Automated Scanning for Corrupted Archive Files

  - by Synetech inc.

  Hi, I have all kinds of files that I have downloaded from everywhere over the years scattered around my hard drives. I’m in the process of trying to organize them all and have run into a problem. Sometimes a file was not downloaded correctly (this was a big issue when Chromium first came out) and is thus corrupt. For media files, this is relatively simple to determine (it requires actually opening and examining the file). For executables or other binaries, it is relatively difficult (executables may or may not crash, other binaries could be completely unknown). Archive files (eg zip, rar, 7z, exe, ace, etc.) however should be pretty simple, they have a built-in corruption detection facility. My problem now is that I really don’t want to open and test each and every single archived file throughout my drive; that would be a nightmare. I’m looking for a utility that can automate the process. Is there a program that can scan archive files on a drive and list the ones that are corrupt? Thanks a lot.

  Read the article

• CentOS - mdadm raid1 drive won't mount to default location

  - by danny

  I'm running CentOS 5.5, the system, boot, swap, etc. is all on /dev/sda and I have two identical single-partition drives /dev/sdb1 /dev/sdc1 that are configured in RAID1 (using mdadm). It was working fine (configured to mount to /mnt/data in the fstab file) and I recently let yum install a couple of automatic updates without paying attention to what they were, and now it doesn't work. Raid is working fine (dmesg shows it gets loaded correctly). mdstat shows: # cat /proc/mdstat Personalities : [raid1] md0 : active raid1 sdc1[1] sdb1[0] XXXX blocks [2/2] [UU] unused devices: <none> Additionally, I can mount it anywhere other than its default directory (i.e. the following works, and I can read data off the drives). # mount /dev/md0 /mnt/data2 EXT3-fs warning: mounting fs with errors, running e2fsck is recommended But when I run the following I get: # mount -a mount: /dev/sdb1 already mounted or /mnt/data busy It says nothing is mounted when I try to umount /dev/sdb1 or umount /mnt/data, so I assume it's the second of those errors. However, lsof | grep mnt shows nothing. The weird thing is that I can save files in /mnt/data. So something is obviously mounted there, but when I try to umount it I get the error that nothing is mounted. /etc/mtab doesn't mention any of the partitions or files I am trying to work with, and fstab just has that one line I mentioned above that is supposed to mount my raid partition. Again, it was all working fine until I On Google I've found a few things about dmraid interfering with mdadm after an update, but I yum remove'd dmraid and rebooted and it didn't help. I'm really confused and need to get this working to get on with my work!

  Read the article

• Unix: Files starting with a dash, -

  - by Svish

  Ok, I have a bunch of files starting with a dash, -. Which is not so good... and I want to rename them. In my particular case I would just like to put a character in front of them. I found the following line that should work, but because of it dash it doesn't: for file in -N*.ext; do mv $file x$file; done If I put an echo in front of the mv I get a bunch of mv -N1.ext x-f1.ext mv -N2.ext x-f2.ext Which is correct, except of course it will think the first filename is options. So when I remove the echo and run it I just get a bunch of mv: illegal option -- N I have tried to change it to for file in -N*.ext; do mv "$file" "x$file"; done but the quotes are just ignored it seems. Tried to use single quotes, but then the variable wasn't expanded... What do I do here? Update: I have now also tried to quote the quotes. Like this: for file in -N*.ext; do mv '"'$file'"' '"'x$file'"'; done And when I echo that, it looks correct, but when I actually run it I just get mv: rename "-N1.ext" to "x-n1.ext":: No such file or directory I have just no clue how to do this now... sigh

  Read the article

• Make isolinux 4.0.3 chainload itself

  - by chainloader

  I have a bootable iso which boots into isolinux 4.0.3 and I want to make it chainload itself (my actual goal is to chainload isolinux.bin v4.0.1-debian, which should start up the Ubuntu10.10 Live CD, but for now I just want to make it chainload itself). I can't get isolinux to chainload any isolinux.bin, no matter what version. It either freezes or shows a "checksum error" message. I'm using VMWare to test the iso. Things I have tried: .com32 /boot/isolinux/chain.c32 /boot/isolinux/isolinux-debug.bin (chainload self) this shows Loading the boot file... Booting... ISOLINUX 4.03 2010-10-22 Copyright (C) 1994-2010 H. Peter Anvin et al isolinux: Starting up, DL = 9F isolinux: Loaded spec packet OK, drive = 9F isolinux: Main image LBA = 53F00100 ...and the machine freezes. Then I've tried this (chainload GRUB4DOS 0.4.5b) chainloader /boot/isolinux/isolinux-debug.bin Result: Error 13: Invalid or unsupported executable format Next try: (chainload GRUB4DOS 0.4.5b) chainloader --force /boot/isolinux/isolinux-debug.bin boot Result: ISOLINUX 4.03 2010-10-22 Copyright (C) 1994-2010 H. Peter Anvin et al isolinux: Starting up, DL = 9F isolinux: Loaded spec packet OK, drive = 9F isolinux: No boot info table, assuming single session disk... isolinux: Spec packet missing LBA information, trying to wing it... isolinux: Main image LBA = 00000686 isolinux: Image checksum error, sorry... Boot failed: press a key to retry... I have tried other things, but all of them failed miserably. Any suggestions?

  Read the article

• VMware Server Host-Only Network Routing

  - by Chris

  I have a windows 2008 web server machine running VMware server. I have 3 VM's - All 3 are test servers so security isn't really a concern... each of them running windows 2008 standard and some of them serving web content. My ISP only allows one MAC address to access the physical switch, however they give me 10 public IP addresses to use. My question is, if I put each VM on their own Host only network, how can I route all traffic from a specific public IP on the host, to the corresponding host only adapter, therefore routing to the specific VM? For example: A single physical Adapter on the Host has the following public IP's assigned to it in windows networking: 74.208.14.10 74.208.14.20 74.208.14.30 Each VM is on a host-only network vm1 - 192.168.196.1 vm2 - 192.168.197.1 vm3 - 192.168.198.1 On the host, I want to route all traffic from 74.208.14.10 to VM1 and 74.208.14.20 to VM2 and 74.208.14.30 to vm3 without using VMware NAT, or bridged connections. I want each server to appear to have its own public IP address. My guess is i can modify the route tables somehow, or perhaps in ICS...but i'm not sure how.

  Read the article

• Hosting websites in our Workplace custom-built datacentre

  - by i.h4d35

  I'm faced with unique learning opportunity at work at the moment. Due to the slowdown (amongst other reasons), the powers that be at my office have decided to abandon our shared hosting providers (both shared and dedicated hosting) and have decided to host the websites at our office's datacentre. We're running 7 websites, wherein the average unique hits per day at the moment is about 900. We have 2 servers set aside for this - one is a DELL POWER EDGE 1850 (Intel Xeon 3 GHZ*2, 4GB RAM, 73GB HDD and the other is an HP DL 380 G3 (Intel Xeon 2.8 GHz, 6 GB RAM, 73 GB HDD) a) I would like to know the pros and cons of going ahead with this project.All the sites will be hosted on a single IP. In all probability, the OS is going to be CentOS. b) Do you think I should consider Virtualization into this equation (KVM/Xen)? I was thinking in terms of separate instances of the DB server and the frontend though I do not know if this is the best way to go. c) Should I be trying to use cloud stacks like OpenStack and try to make it look like websites hosted on some sort of Public Cloud? (something that I checked out here). Here is something else I came across, which looks similar to what needs to be done at our office. About the websites - Of the 7 websites, 4 are basic static websites which basically gives a whole lot of information about a few local institutions. The remaining 3 are local product-based websites developed in PHP wherein end user can view products and order them online. I am trying to take this as a learning experience wherein I can learn to build something from scratch and save the company a little something in the process. The migration needs to be completed by Easter so I guess it gives us some time (or am I being overly optimistic??). I am confused here and would appreciate all the help I can get. Thanks in advance.

  Read the article

• Windows XP periodically disconnects, reconnects; Windows 7 doesn't

  - by einpoklum

  My setup: I have a PC with a Gigabyte GA-MA78S2H motherboard (Realtek Gigabit wired Ethernet on-board). I have the latest drivers (at least the latest driver for the NIC. I'm connecting via an Edimax BR-6216Mg (again, wired connection). For some reason I experience short periodic disconnects and reconnects. Specifically, Skype disconnects, tries to connect, succeeds after a short while; incoming SFTP sessions get dropped; using a browser, I sometime get stuck in the DNS lookup or connection to the website and a page won't load. A couple of seconds later, a reload works. All this happens with Windows XP SP3. With Windows 7, it doesn't happen. The connection is smooth (OS is sluggish though, but never mind that). Like I said, I updated the NIC driver. I tried reducing the MTU (used something called Dr. TCP), thinking maybe that would help, but it didn't. (I'm a bit but not super-knowledgeable about TCP parameters.) I'm guessing it's either a problem with the driver or some settings which are different between the two OSes. ipconfig for my adapter: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1D-7D-E9-72-9E Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.0.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.254 DHCP Server . . . . . . . . . . . : 192.168.0.254 DNS Servers . . . . . . . . . . . : 192.117.235.235 62.219.186.7 Lease Obtained. . . . . . . . . . : Saturday, March 10, 2012 8:28:20 AM Lease Expires . . . . . . . . . . : Friday, January 26, 1906 2:00:04 AM

  Read the article

• Win 7 dual monitor: Don't move application windows when turn off second monitor

  - by codewaggle

  The title is correct, it should say "Don't" not "Doesn't". I Don't want the application windows to be moved to the main monitor when I turn off the monitors. On my Win XP dual monitor system, I can turn off the monitors and when I turn them back on, the application windows are in the same locations on the same monitors as when I turned the monitors off. On the Win 7 system, every time I turn off the monitors (or just the second monitor), all of the application windows are moved to the "main" monitor. After experimenting with the settings, I've found one process that enables me to turn off the monitors and still keep my application windows laid out in my chosen locations on the two monitors: 1) Switch the display setting to a single monitor. 2) Turn off the monitors. 3) Turn on the monitors. 4) Switch the display setting back to "Extend these Displays". After step 4, the application windows that I had laid out on the second monitor are moved back to their original locations on the second monitor. Is there a windows or nVidia setting that would leave the application windows on the second monitor so that I don't need to switch the display settings every time I turn off the monitors? Specs: Windows 7 64-bit dual monitors (1 DP, 1 DVI) Desktop (most questions seem to be about laptops) nVidia Quadro 2000 nVidia Control Panel nVidia nView Control Panel

  Read the article

• Simple options for port forwarding to a different port?

  - by Nick

  I have three network printers at our local office, all of which listen on port 9100. Non of them offer the option of changing the listening port. We have a single public static IP address, and access to our main network is through a Linksys WRT-54G. We need to be able to print to these printers from outside the office. The problem is, with the 54G, I can only forward a port to the SAME port on a particular IP address. What I really need though is a way to forward to an ip address and a DIFFERENT port. I need to do this: In port Destination 9100 192.168.1.1 : 9100 9101 192.168.1.2 : 9100 9102 192.168.1.3 : 9100 So I'm looking for options. I could setup an old computer with two network cards and IPtables I suppose, but that seems like a lot of overhead for something relatively simple. Is there a way a virtual machine (read: one network card) could do the advanced port forwarding? Where I forward all traffic to it, and it forwards it on to the right printer? Or what about those mini Linux distros that replace the WRT-54G's firmware? Do any of those support what I need "out of the box"? I have a spare WRT- could I make it an IP tables router? Recommendations for mini distros? Or is there an off-the-shelf product that does this (cheap/local preferred)? Any advice / options appreciated. Thanks!

  Read the article

• DNS-Based Environment Determination

  - by zvolkov

  Found the following here. The questions is: where can I find more details on how exactly implement this on Windows? Any guide or how-to anybody? Or maybe you can provide your invaluable suggestions? Specifically, how do I make so that "all QA servers would first resolve entries in qa.example.com first and then if that lookup failed they would try example.com" (I'm a dev, not a DNS specialist, but our IT Support has refused to help on this:() Use DNS Based Environment Determination for your servers. Do this by initially splitting your top level domain into a number of sub domains depending on their function, and then creating DNS Service Names in each of the sub domains pointing to the relevant server for that service. Based on the list above we would then have: * clientdb.prod.example.com for Production * clientdb.perf.example.com for Performance Testing * clientdb.qa.example.com for QA * clientdb.dev.example.com for Development Servers then resolve entries in their relevant sub domain by function. That is, all QA servers would first resolve entries in qa.example.com first and then if that lookup failed they would try example.com. This allows you to have a single configuration entry for your client database hostname (clientdb) that would resolve correctly in all environments. This technique has the added advantage of still having global services defined in a common top level domain. This seems to be related to Providing "split horizon" DNS service. Reading that, I see that I will probably need separate DNS Server for each environment. Is this true or does Windows support some form of "tagging" the records to be visible depending on the requestor's IP?

  Read the article

• Recommendations for colocation in the US

  - by Emil

  Hello serverfault I work for a European media company and we are currently looking for colocation in the US. I know the European market quite well unfortunately that is not the case for the US. I'm hoping for you guys to help me out a bit with a few questions, it would be much appreciated! I am looking for a data center that can deliver a high level of availability (tier 3 or better). The installation will be fairly large so capacity is important. Good internet connectivity/carrier presence. However most important is good customer support, skilled dedicated and responsive technical staff, since we won't have tech staff close by. I'm looking for a small and fast moving company that target internet businesses rather than big old enterprise hosting. What locations should we go for given that we want to reach all of the US from a single site and still maintain decent latency? (do we need east and west coast?) Where are the main internet hubs and should you try and get as close as possible? Are there any good online resources I should look at? Where do the large scale internet/media services colocate? Lastly I would be very happy to get some actual recommendations for companies to talk to P.S I'm happy to return the favor if anyone has question regarding data centers and colocation in Europe.

  Read the article

• What Wireless Router/ADSL Modem to get? N-band a must!!

  - by JJarava

  I'm looking for a Dual-N band Router OR ADSL Gateway and I'd like some recommendations. Situation: I have a 802.11b/g ADSL gateway provided by my telco, but the WIFI signal won't cover all the house (especially the living-room, so my tv-connected Mac Mini has poor to no internet access). So I'm looking to either replace the DSL modem with a N-enabled one, or to add a Router to the mix. I've had a modem+router setup for many years, and I know the advantatges (double NAT, double FW = more security) and issues (more complex to troubleshoot, two possible points of failure), so I'd rather live with a single (ADSL Gateway) device, if possible. Requirements: Dual-N Band (300 Mbs WIFI) 1 GB Ethernet ports ADSL2+ support (if it's a ADSL gateway, which would be desirable) "Best" range and speed possible Nice to have: USB port to share disks/printers on the network Media streaming I've been a long time user of Linksys, so googling around I found the WRT610N (http://www.linksysbycisco.com/US/en/products/WRT610N) for a "Pure Router" perspective, and it's one of those that Linksys styles "N++" (http://www.linksysbycisco.com/US/en/promo/Promotion-Go-Wireless?stepname=Promotion-Step-Go-Wireless-High-Performance) But I haven't been able to find similar "ADSL" gateways. I've found the WAG320N, but there is little to no info in the Linksys site (i.e., i don't know if it's Dual Band, or if it has GB ethernet) Any opinions/recommendations of other products/suggestions are more than welcome.

  Read the article

• Apple Mac OS X Mavericks inside Virtual Box

  - by John Sonderson

  I have a few questions regarding Mac OS X and OS virtualization. A. Given all the legal restrictions imposed by Apple on Apple products, I would like to know whether it is legal to install the new and freely downloadable Apple Mac OS X Mavericks inside Oracle Virtual Box. B. What about older OS X versions such as Mountain Lion? C. How many machines can I install it on. What if I don't use the Mac to which the OS is downloaded but only use it on Virtual Box, and prefer to, say, install Linux on the Mac computer so that it doesn't become unusable due to the single user license policy and me running the OS on Windows 7 within Virtual Box? D. I have a PC running Windows 7 but would like to get the OS off a second had Mac I'm planning to purchase for this purpose. How must we proceed to copy the OS to an ISO so that I can install it on Windows 7? I am unfamiliar with Macs and do not know what software to use for the purpose, nor where the OS is downloaded to (as an ISO, .app executable, .gz or .zip file or whatever). If anyone could provide some guidance with the process I would sincerely appreciate it. Thanks.

  Read the article

• Run command remotely on Windows computer from C#

  - by Bilal Aslam

  I have a Windows Server 2008 instance on Amazon EC2 (Amazon's cloud compute platform, which provides VMs in the cloud). It has an external IP, and I have an admin account on the box. I would like to 'bootstrap' this instance remotely i.e. I want to run commands to download, install and configure apps on it, all without having to log on even once. Also, I cannot use psexec on the source computer. I have figured out how to do this to a remote, domain-joined computer using WMI. However, I have NOT been able to do for a remote computer on EC2. Here are some specific restrictions: 1) The remote computer is not part of my domain, hence no Kerberos 2) The remote computer does not have a cert I trust, or vice versa I am sure I am running into to some auth/trust restriction. Is there any way I can run a single command on the remote, given that I have admin privileges? I'm not tied down to using WMI, but I do need to run a command somehow. Feels like this should be a solved problem.

  Read the article

• How to forceably unmount stuck network share in Mac OS X?

  - by Kyle Lowry

  Not long ago my Xserve failed (power loss) while an iMac was working with files on a particular network share (called "Work Share"). This volume, "Work Share", is now stuck. It can't be seen in the GUI, you can only detect it using the Terminal. Even after power cycling over the course of several days, ls -a still shows that it's there, but I can't unmount it using any command - not even as root in single user mode. Every time I attempt to unmount that volume, I get the message that the resource is busy (which it can't possibly be since nothing is using it), and error code 4915. The issue is that when I mount the real "Work Share", it internally is renamed to "Work Share-1", which breaks all my links, and several files in the share. If I can't unmount the false "Work Share", then that computer would be unuseable without a reformat, I would imagine - and I don't want it to have to come to that. I've tried everything I can think of - it looks like sudo can't save me now. Any ideas on how to unmount this stuck volume?

  Read the article

• IIS 7.5 Siteminder is not protecting ASP.net MVC requests

  - by HariM

  We are trying to use ASP.Net MVC with Siteminder for Single Sign on. This is on Windows Server 2008 R2 with IIS 7.5. Siteminder Agent version 6QMR6. Problem : Siteminder protects physical files that are exist. And it is not protecting the folder when we try to access a non existed file. It must redirect to login page even if the file doesn't exist when the user is accessing a protected folder. How to configure in IIS 7.5 that Do not verify a file exist, before authentication by siteminder. SiteMinderWebAgent is a Handler(WildCard Script Map) we created using the ISAPI6WebAgent.dll How to Protect ASP.Net MVC Request with Siteminder? (Added this as My previous question did not solve the problem). MVC Request shows up in IIS Log but not in Siteminder log. Update : Microsoft Support says currently IIS7.5, even in earlier versions doesnt support wildcard mappings on any two Isapi Handlers with * wild card. Currently in my case Siteminder has * wildcard and asp.net mvc (handler is aspnet_isapi) has * wildcard to handle the reqeusts. Ordered priority doesnt work in the wild card mappings case with Just *. Did not convinced with the answer but will wait till tomorrow for them to get back.

  Read the article

< Previous Page | 538 539 540 541 542 543 544 545 546 547 548 549  | Next Page >