Search Results

Search found 16035 results on 642 pages for 'connection pooling'.

Page 544/642 | < Previous Page | 540 541 542 543 544 545 546 547 548 549 550 551  | Next Page >

• (Win7) Gets stuck with ~1% CPU. Especially with multithreading

  - by meow

  Windows 7 32 bit, up to date, Intel i7 860. (For some reason the company runs 32bit Windows everywhere.) I tried to update all motherboard drivers etc. as far as possible. I have a performance issue with a machine which appears in connection with multithreading (or so I think). As an example (and where I most often see it, but it appears on other programs as well): ProteoWizard is a file conversion tool for mass spectrometry files. I can add a list of files and it will attempt to process up to 8 files in parallel (quadcore x 2 threads/core). If I choose 1 to 6 files, I start the process and it goes straight through. If I have =7 files in the queue, conversion goes to ~20%, then gets stuck for 15 seconds, then continues again, always in "chunks" of a few % before getting stuck again. During the time the process is stuck, CPU is at 1%. RAM is not limiting, it is maybe at 70% or so and not going up. I don't get the same problem on other, even slower machines. The computer gets also stuck at 1% CPU doing nothing on other occasions, but for multithreading it is most frequent. Where should I look for the problem?

  Read the article

• FTP Server upload and filesystem questions

  - by Alex

  I'm a photographer who mainly does event photography. A while ago I bought myself a Nikon WT-4 wireless transmitter, a small device which connects via USB to my Nikon D700 DSLR, and then establishes a WiFi connection to an existing WLAN. It can then upload any pictures I take via FTP to an FTP server somewhere in the network. On my laptop I then have a piece of software which will check a given folder on the disk regularly, this software is smart enough to look at the modified file timestamp, if this timestamp is less than 10 seconds ago, it will not attempt to import the folder and skip the file in this iteration of the import scan. The problem I've discovered seems to be inherent to the FTP protocol, as I have the same problem with Windows 7 built in IIS server, as I do with FileZilla FTP server. When the transmitter starts to upload a file, the FTP server will create a small 300-500 KB file with the correct filename on the disk, but then do nothing with the file until it has completely received the file via FTP. So it seems to create this small dummy file, and then buffer the remainder of the FTP upload until it's finished, and then dump the rest of the file into the dummy file making it the correct size. Problem is, these uploads take about 15-30 seconds depending on reception, but since the folder watch tool will already try to import any file older than 10 seconds, it will always try to import the small dummy files which obviously fails as they're not copmlete yet. Is there any way to 'disable' this behaviour? Ideally I would like my file only to show up once it's been completely uploaded. Or perhaps someone knows another FTP server application (it has to run on win7) which does not show this behaviour?

  Read the article

• iptables: How to combine DNAT and SNAT to use a secondary IP address?

  - by Que_273

  There are lots of questions on here about iptables DNAT/SNAT setups but I haven't found one that solves my current problem. I have services bound to the IP address of eth0 (e.g. 192.168.0.20) and I also have a IP address on eth0:0 (192.168.0.40) which is shared with another server. Only one server is active, so this alias interface comes and goes depending on which server is active. In order to get traffic accepted by the service a DNAT rule is used to change the destination IP. iptables -t nat -A PREROUTING -d 192.168.0.40 -p udp --dport 7100 -j DNAT --to-destination 192.168.0.20 I also wish all outbound traffic from this service to appear to come from the shared IP, so that return responses will work in the event of a active-standby failover. iptables -t nat -A POSTROUTING -p udp --sport 7100 -j SNAT --to-source 192.168.0.40 My problem is that the SNAT rule is not always run. Inbound traffic causes a connection tracking entry like this. [root]# conntrack -L -p udp udp 17 170 src=192.168.0.185 dst=192.168.0.40 sport=7100 dport=7100 src=192.168.0.20 dst=192.168.0.185 sport=7100 dport=7100 [ASSURED] mark=0 secmark=0 use=2 which means the POSTROUTING chain is not run and outbound traffic leaves with the real IP address as the source. I am thinking I can set up a NOTRACK rule in the raw table to prevent conntracking for this port number, but is there a better or more efficient way to make this work? Edit - Alternative question: Is there a way (in CentOS/Linux) to have an interface that can be bound to but not used, such that it can be attached to the network or detached when a shared IP address is swapped between servers?

  Read the article

• Enabling http access on port 80 for centos 6.3 from console

  - by Hugo

  Have a centos 6.3 box running on Parallels and I'm trying to open port 80 to be accesible from outside tried the gui solution from this post and it works, but I need to get it done from a script. Tried to do this: sudo /sbin/iptables -A INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT sudo /sbin/iptables-save sudo /sbin/service iptables restart This creates exactly the same iptables entries as the GUI tool except it does not work: $ telnet xx.xxx.xx.xx 80 Trying xx.xxx.xx.xx... telnet: connect to address xx.xxx.xx.xx: Connection refused telnet: Unable to connect to remote host UPDATE: $ netstat -ntlp (No info could be read for "-p": geteuid()=500 but you should be root.) Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN - tcp 0 0 127.0.0.1:6379 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN - tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN - tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:37439 0.0.0.0:* LISTEN - tcp 0 0 :::111 :::* LISTEN - tcp 0 0 :::22 :::* LISTEN - tcp 0 0 ::1:631 :::* LISTEN - tcp 0 0 :::60472 :::* LISTEN - $ sudo cat /etc/sysconfig/iptables # Generated by iptables-save v1.4.7 on Wed Dec 12 18:04:25 2012 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [5:640] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT # Completed on Wed Dec 12 18:04:25 2012

  Read the article

• Terratec Cinergy Hybrid T USB XS is not recognized anymore on Mac OS X

  - by Gabble

  I have used Terratec Cinergy Hybrid T USB XS for years now, alongside with Elgato EyeTV software. I am a happy and completely satisfied user! Since a couple of weeks the USB sitck stopped working on my MacPro1,1 (OS version 10.6.3): EyeTV does not see any device attached, and actually, the green led on the stick stays off. It is not a USB port fault: I have unplugged any other USB/Firewire device and tried with different USB ports, to no avail (any other USB devices work as expected on any port) I have completely uninstalled EyeTV software, including preferences and system daemons/extensions, rebooted and reinstalled the latest EyeTV. No way. Reset the PRAM. Nope. Checked the Apple System Profiler - USB: No device attached, The MacPro does not see it at all. I need to say that: a) The device worked as a charm even with the latest OS 10.6.x (so it's not a OS upgrade cause). b) I have plugged the Terratec Cinergy Hybrid T USB XS to my MacBook5,1 where EyeTV is not installed and was never installed: The green led on the stick turns on, the growl bubble pops up, and the device is perfectly recognized by the system. Apple System Profiler says (sorry, Italian language): Cinergy Hybrid T USB XS (2882): ID prodotto: 0x005e ID fornitore: 0x0ccd Versione: 1.10 Numero di serie: 061102005755 Velocità: Fino a 12 Mb/sec Produttore: TerraTec Electronic GmbH ID posizione: 0x04100000 Corrente disponibile (mA): 500 Corrente necessaria (mA): 500 At this point I am pretty sure the Terratec stick is not damaged and there is something wrong with my MacPro. I kindly ask you: Is there a way to force my MacPro recognize the USB device? What can I check? Is there something that caches USB connection that can be reset? A OS reinstall would be the very last resort for me. Thanks in advance for any help you will offer!

  Read the article

• How to detect/list rogue computers connected to a WIFI network without access to the Wifi Router interface? [migrated]

  - by JJarava

  This is what I believe to be an interesting challenge :) A relative (that leaves a bit too far to go there in person) is complaining that their WIFI/Internet network performance has gone down abysmally lately. She'd like to know if some of the neighbors are using her wifi network to access the internet but she's not too technically savvy. I know that the best way to prevent issues would be to change the Router password, but it's a bit of a PITA having to re-configure all wifi devices... and if the uninvited guest broke the password once, they can do it again... Her wifi router/internet connection is provided by the telco, and remotely managed so she can log-on to their telco account's page and remotely change the router's Wifi password, but doesn't have access to the router status page/config/etc unless she opts out of the telco's remote support and mainteinance service... So, how could she check if there are guests in the wifi with this restrictions and in the most "point and click way"? In this case I'd probably use nmap to look for other devices in the network, but I'm not sure if that's the easiest way to do it. I'm not a wifi expert, so I don't know if there are any wifi-scanning utils that can tell us who's talking to the router... Lastly, she's a Windows user as I guess that'll influence the choice of tools available Any suggestions more than welcome Regards!

  Read the article

• SSH to remote host (edgemarc 4200 or 4500 series routers) and pull arp data

  - by MaQleod

  I've been trying to think of a method to do this for days, but have not come up with anything yet. Ideally, this is what I'm looking to do: From a windows XP machine, I need to open an SSH connection to a remote host, send the arp command, and pull the text results of the command back for use on the client. I will need to parse this data and preferably produce a 2D array of IPs and MAC addresses. There will be no shared keys, this is all done with a username and password that will always be different, they will need to be fed into the command via variables that will be pulled from a database using an autoit script based on the WAN ip of the remote host. Now the actual parsing of the data and creation of the array will be easy if I can just get the text of the arp table. Is there any way to ssh to a remote host, run a command and return the data from that command to the client in a batch script or perl script (it is ok if it writes the text to a file, I can read it out of the file later, I just need it to get to the client)?

  Read the article

• Windows Share permissions

  - by Armando

  I have a SQL/File server that I am replicating a File Share and SQL instance, using ArcServer RHA, to a Replica server. Everything seems to work as far as the replication of the SLQ instance and Share is concerned. When I fail over to the Replica server the DNS Host A record is modified to point to the Replica Server IP Address so if I do an NSLOOKUP on ServerA it then points to the IP Address of ServerB. Ans since the SQL instance is named the same I can still map my ODBC connections to ServerA and I can still make a SQL connection. When I try to do a \ServerA\Share I get an error that says I do not have permissions to the Share. I think this is because it uses keberose authentication and the Share is tied to the actual sever host name. I have tried puting in a CNAME and pointing it to ServerA and Disabling Strict Name Checking on ServerB as well as adding the CNAME to the OptionalNames in the registry but I am still getting the error when I have the ServerA powered off. Is there a way to reset the Authentication of the Share to use the DNS Cname?

  Read the article

• Protect all XML-RPC calls with HTTP basic auth but one

  - by bodom_lx

  I set up a Django project for smartphone serving XML-RPC methods over HTTPS and using basic auth. All XML-RPC methods require username and password. I would like to implement a XML-RPC method to provide registration to the system. Obviously, this method should not require username and password. The following is the Apache conf section responsible for basic auth: <Location /RPC2> AuthType Basic AuthName "Login Required" Require valid-user AuthBasicProvider wsgi WSGIAuthUserScript /path/to/auth.wsgi </Location> This is my auth.wsgi: import os import sys sys.stdout = sys.stderr sys.path.append('/path/to/project') os.environ['DJANGO_SETTINGS_MODULE'] = 'project.settings' from django.contrib.auth.models import User from django import db def check_password(environ, user, password): """ Authenticates apache/mod_wsgi against Django's auth database. """ db.reset_queries() kwargs = {'username': user, 'is_active': True} try: # checks that the username is valid try: user = User.objects.get(**kwargs) except User.DoesNotExist: return None # verifies that the password is valid for the user if user.check_password(password): return True else: return False finally: db.connection.close() There are two dirty ways to achieve my aim with current situation: Have a dummy username/password to be used when trying to register to the system Have a separate Django/XML-RPC application on another URL (ie: /register) that is not protected by basic auth Both of them are very ugly, as I would also like to define a standard protocol to be used for services like mine (it's an open Dynamic Ridesharing Architecture) Is there a way to unprotect a single XML-RPC call (ie. a defined POST request) even if all XML-RPC calls over /RPC2 are protected?

  Read the article

• What differences are there between "home" switches and "professional" switches?

  - by pjreddie

  Our radio station uses a PtP wireless system to stream our radio and TV signals from our studio up a hill to our transmitter. We have been having problems with warbly sound and drop outs that come from some point in this system. An engineer that occasionally visits the station thinks it could be the switches we use on each side of the PtP wireless system to connect the PtP devices to the encoders and decoders and wants us to get two of these switches: http://www.amazon.com/Netgear-JGS516-ProSafe-16-Port-Ethernet/dp/B0002CWPOK/ref=dp_return_1 The encoder/decoder setup only streams 8Mbps total so it seems like the switches we have should not be stressed out, unless they are causing sufficient latency to degrade the performance of the encoder/decoder. At each end of the connection we only have 4 connections, is there any reason we couldn't get a cheaper, "home" quality switch like this: http://www.amazon.com/D-Link-DGS-1005G-5-Port-Gigabit-Desktop/dp/tech-data/B003X7TRWE/ref=de_a_smtd Is there a significant difference that we would notice in terms of latency between these two switches? How much does the quality of the switch actually matter in this scenario? Any help is appreciated, feel free to ask questions if anything needs clarification. Thanks

  Read the article

• System With Two Network Adapters

  - by Synetech inc.

  Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

  Read the article

• Use both OpenVPN & eth0 together

  - by shadyabhi

  I connect to a VPN using openVPN. Now, after the connection is established, all my traffic goes through tun0. My LAN gateway is 10.100.98.4... So, for apps to use my direct internet connnection I did sudo route add default gw 10.100.98.4 But, I cant use tun0 now. I know this because curl --interface tun0 google.com doesnt give me anything.. How do I go about using both connections simultaneously. How can I achieve that? ROUTING TABLES:- Without VPN running:- Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 default 10.100.98.4 0.0.0.0 UG 0 0 0 eth0 With VPN:- Destination Gateway Genmask Flags Metric Ref Use Iface 10.10.0.1 10.10.54.230 255.255.255.255 UGH 0 0 0 tun0 10.10.54.230 * 255.255.255.255 UH 0 0 0 tun0 free-vpn.torvpn 10.100.98.4 255.255.255.255 UGH 0 0 0 eth0 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 default 10.10.54.230 0.0.0.0 UG 0 0 0 tun0 After the route command- Destination Gateway Genmask Flags Metric Ref Use Iface 10.10.0.1 10.10.54.230 255.255.255.255 UGH 0 0 0 tun0 10.10.54.230 * 255.255.255.255 UH 0 0 0 tun0 free-vpn.torvpn 10.100.98.4 255.255.255.255 UGH 0 0 0 eth0 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 default 10.100.98.4 0.0.0.0 UG 0 0 0 eth0 default 10.10.54.230 0.0.0.0 UG 0 0 0 tun0

  Read the article

• realtek lan driver problem - win 7

  - by tango _123

  Hi, my new notebook (ACER TM 8371) with Win 7(x32) professional as OS, has strage behaviour with respect to LAN. when I plug or unplug my charger cable, or my notebook goes in stad-by, or just a do nothing, the netwrok connection is lost. All the energy savings functionbality have been in-activated. if i check the network adapter information, it says "a network cabel is unplugged or corrupted", but it is not true.....the cable is in and it is not corrupted (i tried several which works on other machines). if a tried to di-habilitate and hence re-habilitate, it allows di-habilitation and not to further re-habilitate (it says "no driver for the network card" are available). in some cases, also, the driver disappears (i cannot see it anylonger). if i restart the notebook, everything comes back to normality, but.....today in 3 hours i had to restart 6 times!!! can anyone help me? win 7 says the driver is the last one, so no need to update it. here are some techinical information aboiut network card and driver: Name [00000015] Realtek PCIe GBE Family Controller Adapter type Ethernet 802.3 Product type Realtek PCIe GBE Family Controller Installated YES ID device PNP PCI\VEN_10EC&DEV_8168&SUBSYS_02831025&REV_02\4&266E4C4F&0&00E2 last reset 20/11/2009 11:27 Index 15 Service name RTL8167 I/O Port 0x0000FF00-0x0000FFFF Memory address 0xE2500000-0xE2500FFF Memory address 0xE1400000-0xE140FFFF IRQ Channel IRQ 18 Driver c:\windows\system32\drivers\rt86win7.sys (7.3.522.2009, 164,00 KB (167.936 Byte), 28/08/2009 22:12)

  Read the article

• How can I start hostednetwork on Windows 7?

  - by Pirozek

  When I type in admin console command to start hostednetwork netsh wlan start hostednetwork it gives me this: The hosted network couldn't be started. The group or resource is not in the correct state to perform the requested operation. There is a hotfix from Microsoft but it didn't help me. Any advice? C:\Users\Pirozek>netsh wlan show driver Interface name: Wireless Network Connection 3 Driver : D-Link AirPlus DWL-G520 Wireless PCI Adapter(rev .B) Vendor : Atheros Communications Inc. Provider : Atheros Communications Inc. Date : 8.7.2009 Version : 8.0.0.171 INF file : C:\Windows\INF\oem108.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g FIPS 140-2 mode supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Shared WEP-40bit Open WEP-104bit Shared WEP-104bit Open WEP Shared WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP

  Read the article

• mysqldump isn't able to export a specific database, phpMyAdmin crashes

  - by Devils Child

  I'm experiencing problems with a database on my server (Note: All other databases work fine). Once I try to export it with mysqldump I get this error: # mysqldump -u root -pXXXXXXXXX databasename > /root/databasename.sql mysqldump: Couldn't execute 'show table status like 'apps'': Lost connection to MySQL server during query (2013) Also, phpMyAdmin throws an error when selecting this database and immediately logs out. However, the web site which uses this database works fine. I can also execute SELECT statements on the table named "apps" from the MySQL shell. I tried restarting the MySQL daemon as well as REPAIR DATABASE and REPAIR TABLE but the problem still persists. I had this problem before, then it disappeared somehow without me doing anything to resolve the issue. Now, the problem is back and I'm simply unable to create a backup of this database. Used software Debian 6.0.7 x64 MySQL 5.1.66-0 MySQL Version: mysql> SHOW VARIABLES LIKE "%version%"; +-------------------------+-------------------+ | Variable_name | Value | +-------------------------+-------------------+ | protocol_version | 10 | | version | 5.1.66-0+squeeze1 | | version_comment | (Debian) | | version_compile_machine | x86_64 | | version_compile_os | debian-linux-gnu | +-------------------------+-------------------+

  Read the article

• OpenSSL force client to use specific protocol

  - by Ex Umbris

  When subversion attempts to connect to an https URL, the underlying protocol library (openssl) attempts to start the secure protocol negotiation at the most basic level, plain SSL. Unfortunately, I have to connect to a server that requires SSL3 or TLS1, and refuses to respond to SSL or SSL2. I’ve done some troubleshooting using s_client and confirmed that if I let s_client start with the default protocol the server never responds to the CLIENT HELLO: $ openssl s_client -connect server.domain.com:443 CONNECTED(00000003) write:errno=104 --- no peer certificate available --- No client certificate CA names sent --- SSL handshake has read 0 bytes and written 320 bytes --- New, (NONE), Cipher is (NONE) Secure Renegotiation IS NOT supported Compression: NONE Expansion: NONE --- Watching this in Wireshark I see: Client Server -------syn----------> <------ack----------- ---CLIENT HELLO-----> <------ack----------- [60 second pause] <------rst----------- If I tell s_client to use ssl2 the server immediately closes the connection. Only ssl3 and tls1 work. Is there any way to configure openssl to skip SSL and SSL2, and start the negotiation with TLS or SSL3? I've found the OpenSSL config file, but that seems to control only certificate generation.

  Read the article

• SQL Server 2005 to 2008 DB attach elp please!

  - by Brandon

  I have SQL Server 2005 Standard on my personal machine. I created a very big DB about 21 gb. I made a backup and transferred the .bak file via an ftp program to my dedicated server. I have SQL Server 2008 Enterprise Edition on my dedicated server. I tried restore the transferred .bak file but got an error. I posted the error on here and was told the database is corrupt. How? I don't know. The connection was not interrupted during the ftp transfer. The DB works on my own machine. So then I detached the db on my own machine and transferred the mdf and ldf file to my dedicated server through ftp again and again there were not interruptions. Now I try to attach the db and get this error: The header for file 'DB.mdf' is not a valid database file header. The FILE SIZE property is incorrect. (Microsoft SQL Server, Error: 5172) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&ProdVer=10.00.1442&EvtSrc=MSSQLServer&EvtID=5172&LinkId=20476 I already wasted 21 gb transferring the .bak file. Now I used another 21 to transfer mdf and additional ldf file. Please tell me there's a solution. The db can detach and attach fine on my machine in sql server 2005 but not SQL server 2008 on my server.

  Read the article

• SQL Server 2005 SE SP3 on Windows Server 2008 R2 x64 premature query disconnections

  - by southernpost

  New Dell PowerEdge R910, 4x8 Intel X7560, 192GB RAM, hardware NUMA, local RAID, Broadcom NetExtreme II multiport NIC, unteamed, TCP Offload disabled, RSS disabled, NetDMA disabled, Hyperthreading disabled. SQL Server 2005 SE x64 SP3 on Windows Server 2008 R2 EE x64. No other apps on server. Max Mem = 180GB, Max DOP = 4. Existing Windows Server 2003 R2 EE x64 app server connecting to Dell via firewall using SQL Authenticated logins. Symptoms: Intermittent errors at the app server: A transport-level error has occurred when sending the request to the server. (provider: TCP Provider, error: 0 - An existing connection was forcibly closed by the remote host.) Findings: Running queries from SSMS located on another machine within the same domain as the SQL Server run without error. SQLIO showed good performance. Windows and SQL logs show no related messages. Microsoft reveiwed PssDiag trace and stated that "We are not seeing timeouts from SQL Side. The queries bring run against the database are timing out within 9secs. This is a database connectivity error." "we can also see from the AttnSeq column that we are also not seeing any Attentions from the SQL Side.". Dell has confirmed that we are using the latest Broadcom drivers.

  Read the article

• Trouble setting up incoming VPN in Microsoft SBS 2008 through a Cisco ASA 5505 appliance

  - by Nils

  I have replaced an aging firewall (custom setup using Linux) with a Cisco ASA 5505 appliance for our network. It's a very simple setup with around 10 workstations and a single Small Business Server 2008. Setting up incoming ports for SMTP, HTTPS, remote desktop etc. to the SBS went fine - they are working like they should. However, I have not succeeded in allowing incoming VPN connections. The clients trying to connect (running Windows 7) are stuck with the "Verifying username and password..." dialog before getting an error message 30 seconds later. We have a single external, static IP, so I cannot set up the VPN connection on another IP address. I have forwarded TCP port 1723 the same way as I did for SMTP and the others, by adding a static NAT route translating traffic from the SBS server on port 1723 to the outside interface. In addition, I set up an access rule allowing all GRE packets (src any, dst any). I have figured that I must somehow forward incoming GRE packets to the SBS server, but this is where I am stuck. I am using ADSM to configure the 5505 (not console). Any help is very much appreciated!

  Read the article

• pfSense routing between two routers with shared network

  - by JohnCC

  I have a network set-up using two pfSense routers arranged like this:- DMZ1 WAN1 WAN2 DMZ2 | | | | | | | | \___ PF1 PF2___/ | | | | \___TRUSTED___/ Each pfSense router has its own separate WAN connection, and a separate DMZ network attached to it. They share a common TRUSTED LAN between them. The machines on the trusted network have PF1 as their default gateway. PF1 has a static route defined to DMZ2 via PF2, and PF2 has a static route to DMZ1 via PF1. There is NAT to the WAN but internal networks (DMZ1/2 and TRUSTED) use different RFC1918 subnets. I inherited this arrangement, and all used to work fine. I made a config change to PF1 (relating to multicast), and machines on DMZ2 suddenly could not talk to TRUSTED. I rolled the change back, but the problem persisted. What I guess you'd hope would happen is that TCP packets would go DMZ2 - PF2 - TRUSTED and on return TRUSTED - PF1 - PF2 - DMZ2. That's the only way I can see it would have worked. However, PF1 drops the returning packets. I've verified this using tcpdump. I've worked around this by adding static routes to DMZ2 via PF2 to the servers on TRUSTED, but some devices on there do not support static routes so this is not ideal. Is there way to make this arrangement work decently, or is the design inherently flawed? Thanks!

  Read the article

• Is it possible to command a common router without using the web interface?

  - by MDeSchaepmeester

  Some background The internet arrangement in my student home is really weird. There is one ethernet outlet and several wifi hotspots. Either way requires a login through a web site to get internet access. This is annoying as each device needs to login seperately and with a PS3 for example, it is impossible to get connected at all since the web login procedure doesn't work. Therefore I have installed a D-Link DIR-635 router which is connected to the ethernet outlet. It has DHCP enabled so it uses NAT, but whatever it is connected to also uses NAT and I've read this should not work. A fellow student tried it with an Apple Airport but that keeps giving errors related to NAT after NAT. Anyway my setup does work so bonus points if you can clarify this. I need to login to the web site I mentioned earlier with any device, after which all devices in my LAN have connectivity. This is great. Except... In short From time to time, I lose internet connectivity and my D-Link DIR-635 router needs to do a DHCP renew. I can do this via the web interface but my life would be easier if I could just run a cmd file which tells my router to do this without all the hassle. This would setup a connection to my router and execute the proper command. I have tried googling but couldn't find much helpful stuff.

  Read the article

• SSH from ubuntu server to Windows 2008 repeatedly asks for password

  - by jrizos

  I am trying to setup GIT using SSH mode. The central GIT repository is on a NAS device running Windows 2008 server and the user GIT repository is on ubuntu 12.04. When I try to SSH to the windows machine however I am not able to successfully get in. SSH keays are not setup but I think the problem is even before that since I cant get in just by providing the correct password. The output from the SSH command is below. Any help would be appreciated. dba@clpserv01:~$ ssh -v -l administrator clpnas OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug1: Connecting to clpnas [***.***.***.***] port 22. debug1: Connection established. debug1: identity file /home/dba/.ssh/id_rsa type -1 debug1: identity file /home/dba/.ssh/id_rsa-cert type -1 debug1: identity file /home/dba/.ssh/id_dsa type -1 debug1: identity file /home/dba/.ssh/id_dsa-cert type -1 debug1: identity file /home/dba/.ssh/id_ecdsa type -1 debug1: identity file /home/dba/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.5p1 Debian-6+squeeze2 debug1: match: OpenSSH_5.5p1 Debian-6+squeeze2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9p1 Debian-5ubuntu1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA bd:37:d1:98:51:2a:d6:b5:f5:c7:98:d8:74:2c:4e:cd debug1: Host 'clpnas' is known and matches the RSA host key. debug1: Found key in /home/dba/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Trying private key: /home/dba/.ssh/id_rsa debug1: Trying private key: /home/dba/.ssh/id_dsa debug1: Trying private key: /home/dba/.ssh/id_ecdsa debug1: Next authentication method: keyboard-interactive Password: debug1: Authentications that can continue: publickey,password,keyboard-interactive Password:

  Read the article

• Viability of Mac OS X 10.9 Time Machine Server in office environment

  - by user197609

  Currently we have about 20 Mac OS 10.9 MacBook Pros (almost all with SSDs) backing up to individual USB drives. I'd like to consolidate these to one drobo thunderbolt drive array attached to a Mac Mini server (running 10.9 server) using time machine server. My question is, will this scale to 20 users? Examples I have seen seem to be 5 or 6 users tops, and this isn't easy for me to test (I'd rather not ask everyone to backup to the array and then switch back to USB drives if it brings our network to its knees). My primary concern is saturating our gigabit network, as time machine backs up every hour for every machine, so there would usually be a couple people backing up at any given time. We also have some people occasionally on our 802.11ac network and not on ethernet (usually connected via 802.11n until people upgrade to newer machines), but most of the time people are connected to our thunderbolt displays which have a gigabit ethernet connection on them. Our network topology is one 32 port gigabit switch with 5 smaller gigabit switches at each desk cluster. The mac mini server is connected directly to the top level switch. Update: Failing information from someone who has done this in practice, I suppose my question is really around how switches work. If three or four people are backing up simultaneously, and then other two (different) users transfer a file between each other, will they be able to transfer the file at gigabit speeds?

  Read the article

• Can't reliably ping 6224 router from directly-attached system

  - by David Mackintosh

  OK, here's my situation. This is on the internet. The 6224 is the router in this picture and physically resides in Kanata. Both VLAN 1697 and 3994 are provided by an internet service provider. These VLANs are provided through a single 1Gb ethernet wire. The Kanata hosts are directly attached to the 6224; the other two sites are remote. VLAN 3994 is a single IP address space, so theoretically it shouldn't matter physically where the hosts on that subnet are. Here's the problem. I have a monitoring system which is connected further into the internet, so probes from the monitor would come in to this diagram on the 1697 VLAN. When I ping hosts at Albert or Bells Corners from the internet, there is 0 loss. The connection looks perfect. When I ping hosts at Kanata, I lose anywhere from 10 to 40% of the pings. The loss is not predictable, but: when I do lose them, I always lose at least 3, usually 4, rarely more, pings in a bunch. I have attached a monitor directly to the 6224 in Kanata on 3994.. When the monitor pings the 6224 routing interface, I see exactly the same loss pattern -- but NOT at the same time as the loss from the remote system. Ping time is around 1ms. When the monitor pings another system directly attached to the 6224, there is 0 loss. Ping time is about 0.1ms, one-tenth of the time to ping the router. Anyone know what is going on here?

  Read the article

• Mysql server high trafic makes websites really slow or unable to load

  - by Holapress

  Lately we have been having a lot of problems with our mysql server, from websites being really slow or even unable to load them at all. The server is a dedicated server that only runs our mysql database. i have been running some test using a profiler (JetProfiler) and tool to stress test (loadUI). If I use loadUI to connect with 50 simultaneous connections to one of our websites that runs a resently big query it will already make the website be unable to load. One of the things that makes me worried is that when I look at Jetprofile it always shows a Treads_connected of 1.00 and it seems that when it hits around 2.00 that I'm unable to connect. The 3 big peaks are when I run a test with loadUI, first one was 15 simultaneous connections wich made it still able for me to load the website but just really slow, the second one was 40 simultaneous connections which already made it impossible to load and the third one was with 100 connection which also didn't make it load anymore. Another thing that worries me is that in JetProfiler it says all the queries that get used are full table scans, could this maybe be the problem? The website I run as a test runs 3 queries, one for a menu that outputs around 1000 rows, one for the adds that has around 560 rows and a big one to get posts that has around 7000 rows (see screenshot bellow) I also have monitored the cpu of the server and there seems to be no problem there, even when I make a lot of connections with loadui the cpu stays low. I can't seem to figure out what is the main cause of the websites being unable to load when there is a high amount of traffic, if anyone has other suggestions for testing or something that might cause the problem please let me know.

  Read the article

< Previous Page | 540 541 542 543 544 545 546 547 548 549 550 551  | Next Page >